In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

The application of smartphone-based color evaluation of passive sampling devices for gases has only been sparsely reported. The present review aims to compile available publications with respect to the configuration of the passive samplers, conditions of smartphone photographing, analytical procedure for color detection and quantification (including calibration processes), and their application to different target gases. The performance of the methods - whenever available - is presented regarding the analytical specifications selectivity, sensitivity, and limit of detection in comparison with other color evaluation methods of passive samplers. Practical aspects like requirements of instrumentation and ease of use will be outlined in view of the potential employment in education and citizen science projects. In one section of the review the inconsistent terminology of passive and diffusive sampling is discussed in order to clarify the distinction of information obtained from the uptake of the passive samplers between gas-phase concentration and the accumulated deposition flux of gaseous analytes. Colorimetric gas sensors are included in the review when applied in passive sampling configurations and evaluation is performed with smartphone-based color evaluation. Differences in the analytical procedures employed after the passive sampling step and prior to the detection of the colored compounds are also presented.

In the paper, a study of the performance of unmanned ground vehicle (UGV), establishes numerical simulation model of the chassis system by three-dimensional software and finite element analysis software. Based on the numerical modelling and analysis, the work focuses on study of the strength and stiffness of the vehicle's chassis and researched the distribution of stress and deformation under the extremal condition. The paper also presents an autopilot design with new cascade control system for an autonomous motion of an unmanned ground vehicle based on Proportional-Integral-Derivative (PID) and Feed-Forward (FF) control. The PID-FF controller is a part of dedicated for presented UGV used in a hybrid control system for precise control and stabilization, necessary to increase the vehicle motion stability and maneuvers precision. The hybrid PID-FF control system proposed for the ground vehicle model gives a satisfactory quality of control, while maintaining the simplicity of the control system. Presented tests performed in area of mechanical design and control analysis gives good results and proves usefulness of designed unmanned device.

We introduce the Symplectic Structure of Information Geometry based on Souriau’s Lie Group Thermodynamics model, with a covariant definition of Gibbs equilibrium via invariances through co-adjoint action of a group on its moment space, defining physical observables like energy, heat, and moment as pure geometrical objects. Using Geometric (Planck) Temperature of Souriau model and Symplectic cocycle notion, the Fisher metric is identified as a Souriau Geometric Heat Capacity. Souriau model is based on affine representation of Lie Group and Lie algebra that we compare with Koszul works on G/K homogeneous space and bijective correspondence between the set of G-invariant flat connections on G/K and the set of affine representations of the Lie algebra of G. In the framework of Lie Group Thermodynamics, an Euler-Poincaré equation is elaborated with respect to thermodynamic variables, and a new variational principal for thermodynamics is built through an invariant Poincaré-Cartan-Souriau integral. The Souriau-Fisher metric is linked to KKS (Kostant-Kirillov-Souriau) 2-form that associates a canonical homogeneous symplectic manifold to the co-adjoint orbits. We apply this model in the framework of Information Geometry for the action of an affine Group for exponentiel families, and provide some illustrations of use cases for multivariate Gaussian densities. Information Geometry is presented in the context of seminal work of Fréchet and his Clairaut-Legendre equation. Souriau model of Statistical Physics is validated as compatible with Balian gauge model of thermodynamics. We recall the precursor work of Casalis on affine group invariance for natural exponential families.

Research results of the relationships between air-volume in air-entrained cement paste, mortar and concrete, all designed according to PN-EN 480-1 guidelines are presented in the paper. The cement paste, mortar and concrete, with w/c=0,5 ratio, were prepared using innovative air-entraining cement CEM II/B-V. The air-entraining cement CEM II/B-V was produced using two methods: mixed together with natural or synthetic aerated admixture. The air volume test of the volumetric method was carried out in case of fresh cement paste, mortar and concrete mix. Fresh concretes were evaluated in terms of stability of air entrainment and consistency for 5, 20 and 40 min. The porosity structure parameters, like summarized air-content, specific surface of air voids, air-voids spacing factor and micropores content of hardened concrete, were estimated using computed tomography with a resolution of 2-5 μm. The aim of the research was to determine the dependence between air-content of cement paste, mortar and concrete on the measurement of air-entrainment of cement paste or mortar with the same w/c ratio and type of cement, all designed according to PN-EN 480-1 guidelines. Test results proved that there is a good correlation between the measured air-content of the cement paste, mortar and concrete. Therefore, it is possible to predict the aeration of concrete on the air-entrainment of the mortar.

The author demonstrates a stable Lagrangian solid modeling method, tracking the interactions of solid mass particles rather than using a meshed grid. This numerical method avoids the problem of tensile instability often seen with smooth particle applied mechanics by having the solid particles apply stresses expected with Hooke's law, as opposed to using a smoothing function for neighboring solid particles. This method has been tested successfully with a bar in tension, compression, and shear, as well as a disk compressed into a flat plate, and the numerical model consistently matched the analytical Hooke's law as well as Hertz contact theory for all examples. The solid modeling numerical method was then built into a 2-D model of a pressure vessel, which was tested with liquid water particles under pressure and simulated with smoothed particle hydrodynamics. This simulation was stable, and demonstrated the feasibility of Lagrangian specification modeling for fluid–solid interactions.

Particulate matter (PM) is one of the problems faced in environmental science. It has health effects on man and animals in both developed and developing countries. Research and efforts have been on it several years back. Policy statements and efforts have been published. This review paper is an added information on air pollution. In it, efforts were made in discussing these: classification, effects, methodology, case studies and source apportionment. It is hoped that this paper would contribute to existing knowledge on PM.

Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

Diesel is consistently a very popular fuel for internal combustion engines. Its consumption in the European Union has been rising over recent years, as has the number of engines increasingly sensitive to fuel contamination. One of the most important parameters affecting diesel quality is water content. Although its exceedances of the standard’s permissible amount are not common, they carry the risk of serious damage to expensive, modern fuel injection systems. Current methods of measuring water content require both specialised personnel and equipment, as well as transporting the sample to a suitable laboratory. The research presented in this paper was aimed at verifying whether it would be possible to test the moisture content of diesel using impedance spectroscopy. Once refined, such measurement method could be used in situ. Analysing the properties of diesel is challenging, mainly because many types of the fuel are sold, the chemical composition of which is always a well-guarded manufacturer’s secret. The experimental results obtained on many types of commercially available diesel show that it is possible to use impedance spectroscopy to estimate the water content of different types of diesel fuel. The measurement accuracy achieved makes it possible to detect approaching or exceeding the permissible water content.

Although the water absorption feature (WAF) at 970 nm is not very well-defined, it may be used alongside other indices to estimate the canopy water content. The individual performance of a number of existing vegetation water content (VWC) indices against the WAF is assessed using linear regression model. We developed a new Combined Vegetation Water Index (CVWI) by merging indices to boost the weak absorption feature. CVWI showed a promise in assessing the vegetation water status derived from the 970 nm absorption wavelength. CVWI was able to differentiate two groups of dataset when regressed against the absorption feature. CVWI could be seen as an easy and robust method for vegetation water content studies using hyperspectral field data.

In this data deposit, I describe a dataset that is the result of content mining 167,318 published articles for statistical test results. As a result of this content mining, 688,112 results from 50,845 articles were extracted. In order to provide a comprehensive set of data, the statistical results are supplemented with metadata from the article they originate from. The dataset is provided in a comma separated file (CSV) in long-format. For each of the 688,112 results, 20 variables are included, of which seven are article metadata and 13 pertain to the individual statistical results (e.g., reported and recalculated p-value). A five-pronged approach was taken to generate the dataset: (i) collect journal lists, (ii) spider journal pages for articles, (iii) download articles, (iv) add article metadata, and (v) mine articles for statistical results.

This research study focuses on addressing practical optimization challenges in audio-visual content using advanced computational intelligence methods, with a specific emphasis on privacy-preserving issues. The research will be presented as a proposal and can be conducted based on the provided ideas. Computational intelligence encompasses various approaches, including evolutionary algorithms, learning methods, fuzzy systems, and neural networks, which have become essential tools for tackling complex engineering optimization problems due to computational expenses, dimensional complexities, and interdisciplinary integration. The research objectives include a thorough investigation of optimization challenges in audio-visual content, the delineation of problem characteristics, and the development of relevant methodologies based on these specifications. The main goals of the study, titled "Advanced Computational Intelligence Assisted Less-Expensive Privacy-Preserving Optimization," encompass the development of a metamodel-based learning algorithm integrated with evolutionary computation for privacy-preserving optimization, less-expensive signal watermarking optimization using hybrid metamodeling and evolutionary algorithms, and a closed-loop robust intelligent PID control system applied in real-time dynamic signal watermarking. Additional objectives may be defined as the research progresses and further background review is conducted.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

Acute and chronic respiratory diseases impose a significant economic and health burden. Distal small airway assessment requires invasive procedures such as a bronchoscopy and bronchoalveolar lavage. The Particles in Exhaled Air (PExA) device provides a non-invasive means of assessing small airways; it captures distal airway particles sized around 0.5-7m and contains particles of respiratory tract lining fluid (RTLF) that originate during airway closure and opening. The PExA device can measure particle count and mass according to particle size. Subsequent capture of particles in a thin membrane enables application of various analytical methods to assess a broad range of biomolecules including phospholipids, proteins, inflammatory profile, and other metabolites to characterise inflammation and diseases processes such as asthma, chronic obstructive pulmonary disease, acute respiratory distress syndrome, lung cancer, and more recently acute infections such as COVID-19. PExA analysis provides a promising alternative to traditional investigative methods in the assessment, diagnosis, and management of respiratory conditions. By evaluating specific biomarkers in the RTLF associated with airway inflammation, PExA may offer a more accurate and comprehensive understanding of the molecular-level changes in the small airways of patients with acute and chronic lung diseases.

It is concerning that Cameroon's urban centers are experiencing an alarming rise in air pollution as a result of urbanization, population growth, industrial activity, and transportation emissions. We examined the causes, health impacts, research methodology, case studies, and government measures to address the urgent issue of air pollution in Cameroon's urban regions. We have emphasized how Cameroon's air pollution levels have significantly increased as a result of causes like population expansion, urbanization, industrial emissions, and automobile exhaust A thorough discussion of the negative health impacts of extended exposure to air pollution is included, with special attention to the sensitivity of the old and young. These effects include respiratory disorders, cardiovascular ailments, and early mortality. We emphasized the pressing need for all-encompassing strategies to address air pollution, such as increased public awareness campaigns, stronger emissions regulations, the development of renewable energy sources, and better waste management. The techniques employed in studies on air pollution, like as epidemiological research and air quality monitoring, are also explained to provide light on the unique health dangers that Cameroonian urban dwellers must contend with. We emphasized in our conclusion the significance of joint efforts by legislators, medical professionals, and the general people to reduce air pollution and protect public health in Cameroon in order to create a cleaner and healthier future. In order to protect public health in the future, it is imperative that Cameroon's air pollution be addressed.

The article delves into the intricate phase transitions of 1-Octadecanol and n-Nonadecane within a binary system, unveiling dynamic structural changes under varying conditions. Through Fouri-er-transform infrared (FTIR) analysis, specific molecular vibrations were identified, shedding light on the molecular composition and interactions. The study highlights the challenges in detecting subtle phase transitions and emphasizes the individuality of molecular behaviours in closely related compounds. The findings underscore the complexity of phase transitions in binary systems and advocate for a nuanced approach to studying molecular structures and behaviours. Addi-tionally, the research contributes valuable insights into the molecular dynamics of Organic Polymer Functional Adsorption Materials, offering implications for synthetic waxy layers in plant epidermis.

Retiring coal power plants can reduce air pollution and health damages. However, the spatial distribution of those impacts remains unclear due to complex power system adjustments and pollution chemistry and transport. Focusing on coal retirements in Pennsylvania (PA), we analyze six counterfactual scenarios for 2019 that differ in retirement targets (e.g., reducing 50% of coal-based installed capacity vs. generation) and priorities (e.g., closing plants with higher cost, closer to Environmental Justice Areas, or with higher CO₂ emissions). Using a power system model of the PJM Interconnection, we find that coal retirements in PA shift power generation across PA and the Rest of PJM region leading to scenario-varying changes in the plant-level release of several air pollutants. Due to air pollution chemistry and transport and socio-demographics, these changes in turn give rise to a reduction of 10 to 182 PM_2.5-attributable deaths in PJM across the six scenarios, with most reductions occurring in PA. Scenarios that reduce more coal power generation yield greater aggregate health benefits due to air quality improvements in PA and adjacent downwind regions. In addition, vulnerable populations—in both PA and Rest of PJM—benefit most in scenarios that prioritize plant closures in PA near Environmental Justice Areas. These results demonstrate the importance of considering cross-regional linkages and socio-demographics in designing equitable retirement strategies.

Giant unilamellar vesicles (GUVs) are membrane model used to study membrane properties. Electroformation is one of the methods used to produce GUVs. During electroformation protocol dry lipid film is formed. Drying of the lipid film induce Cholesterol (Chol) demixing artifact, in which Chol forms anhydrous crystals, where these crystals does not participate in formation of vesicles. This leads to a lower Chol concentration in the vesicle bilayers compared to the Chol concentration in the initial lipid solution. To address this problem, we propose novel electroformation protocol that includes rapid solvent exchange, plasma cleaning and spin-coating methods to produce GUVs. We tested the protocol focusing on vesicles with high Chol content using different spin-coating durations and vesicle types deposition. Additionally, we compared the novel protocol using completely dry lipid film. The optimal spin-coating duration for vesicles made out of phosphatidylcholine/Chol mixture was 30 s. Mulitlamellar vesicles (MLVs), large unilamellar vesicles (LUVs) obtained by extrusion of MLVs through 100 nm membrane pores and LUVs obtained by extrusion of previously obtained LUVs through 50 nm membrane pores were deposited on electrode for 1.5/1 Chol/phosphatidylcholine lipid mixture and the results were compared. Electroformation using all three deposited vesicle types gave a high GUVs yield, but deposition of LUVs obtained by extrusion of MLVs through 100 nm membrane pores gave the most reproducible results. Using deposition of these LUVs, we produced GUVs with high yield for 6 different Chol concentrations (from 0 % to 71.4%). Using protocol that includes dry lipid film GUVs yield was lower and Chol demixing artifact was induced, proving that the lipid film should never undergo drying when Chol content is high.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

Proteins have the ability to adsorb on the surface of materials, such as soft contact lenses (SCLs), and can affect the hydrophobicity, roughness and surface properties of the contact lenses (CLs), which, in turn, can influence the friction between the lenses and the ocular surface. Excessive friction between contact lenses and the ocular surface can lead to discomfort for the wearer and may cause irritation or inflammation of the cornea, better known as corneal ulcers (keratitis). Bovine serum albumin (BSA) is often used as a standard protein in biocompatibility testing of materials, including contact lenses. One standard commercial contact lenses was tested under lubricated conditions to access the coefficient of friction (CoF), being the contact lubricated with a tear like fluid (TLF) solution containing six different concentrations of BSA. In all cases, a good linearity of the results of the friction force was verified, so the first friction law can be applied to determine the value of the coefficient of friction. It was found that friction increases with increasing protein concentration.

Genetic enhancement of grain production and quality is a priority in wheat breeding projects. In this study, we assessed two key agronomic traits - grain protein content (GPC) and thousand kernel weight (TKW) - across 179 Bulgarian contemporary and historic varieties, and landraces in three growing seasons. Significant phenotypic variation existed for both traits among genotypes and seasons, and no discernible difference was evident between the old and modern accessions. To understand the genetic basis of the traits, we conducted a genome-wide association study with MLM using phenotypic data from the crop seasons, best linear unbiased estimators, genotypic data from the 25K Infinium iSelect array, and a Bonferroni-adjusted p-value. As a result, 776 significant quantitative trait nucleotides (QTNs) organized into quantitative trait loci were discovered, including 25 loci associated with GPC, and 35 loci linked to TKW. Additionally, 14 environmentally stable QTNs were identified for TKW. Certain loci on chromosomes 2A, 3A, and 6B favorably in-fluenced GPC, while the locus on chromosome 6D impacted TKW positively. These loci may reflect novel associations to the two traits. Annotations for proteins involved in the remobilization of carbon and nitrogen from vegetative tissues to developing grain during senescence, as well as in the following buildup of resources required for seed germination, have been found for selected pu-tative candidate genes. These include genes coding for 11S globulin seed storage protein, glutamine synthetase, metalloendopeptidase, components of the ubiquitin/proteasome system, sucrose transporter, alpha-amylase, NAC and bZIP transcription factors. Our findings highlight promising genomic regions for targeted breeding programs aimed at improving grain yield and protein content.

Background: Asthma is a widespread chronic respiratory disease that poses a significant public health challenge. The current study investigated the associations between air pollution and asthma severity among individuals residing near the Sohar industrial port (SIP) in Oman. Despite the presence of multiple major industrial complexes in Oman, limited knowledge regarding their impact on respiratory health is accredited. Hence, the primary objective of this study is to offer valuable insights into the respiratory health consequences of industrial air pollution in Al Batinah North. Methods: The state health clinics' records for patient visits related to asthma were collected for the timeframe spanning 2014 to 2022. Exposure was defined as the distance from SIP, Majan Industerial Area (MIA) and Sohar Industerial Zone (SIZ) to determine high, intermediate, and low exposure zones (12 km, respectively). Exposure effect modifications by age, gender, and smoking status were also examined. Results: The conducted cross-sectional study of 410 patients (46.1% males and 53.9% females) living in over 17 areas around SIP revealed that 73.2% of asthmatics were under 50 years old, with severity significantly associated with closeness to the port. Risk ratios were estimated to be (RR:2.42; CI95%: 1.01–5.78), (RR:1.91; CI95%: 1.01–3.6), and (RR:1.68; CI95%: 0.92–3.09) for SIP, MIP and SIZ areas, respectively, compared to the control area. Falaj Al Qabail (6.4 km) and Majees (6 km) had the highest number of asthma patients (N. 69 and N. 72), and highest percentages of severe asthma cases among these patients (28% and 24%) with significant risk ratios (RR:2.97; CI95%: 1.19–7.45 and RR:2.55; CI95%: 1.00–6.48), correspondingly. Moreover, severe asthma prevalence peaked in the 25-50 age group (RR:2.05; CI95%: 1.26–3.33), and this linkage between asthma and age was much more pronounced in males than females. Smoking and exposure to certain contaminant (dust and smoke) increased also the risk of severe asthma symptoms, but their effects were less important in the high risk zone, suggesting much more important risk factor. A neural network model accurately predicted asthma risk (94.8% accuracy), with proximity to Sohar Industrial Port as the most influential predictor. Conclusion: The study highlights the High asthma burden near Sohar Industrial Port, linked to port proximity and smoking and wind direction as major risk factors. These findings inform vital public health policies to reduce air pollution and improve respiratory health in the region, prompting national policy review.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

To improve efficacy and safety of sunscreen emulsions, UV‐filter skin permeation could be kept as low as possible by reducing UV‐filter content or changing emulsion composition. In this work, different lipid phase ratio (12, 14 and 16% w/w) were assessed for their ability to affect the technological and sensory properties of O/W emulsions in which bemotrizinol (BMTZ), a broad spectrum sunscreen agent, was incorporated free or loaded into nanostructured lipid nanocarriers (NLC) to reduce its release from the vehicle and, hence, its skin permeation. The following technological properties were evaluated in vitro by suitable methodologies: spreadability, viscosity, pH, occlusion factor, BMTZ release, sun protection factor (SPF). Sensory attributes were assessed by trained panelists in three different phases: before/during pick‐up, rub‐in, after application. Raising the lipid phase ratio led to an increase of viscosity and to a corresponding drop of spreadability while the incorporation of BMTZ‐loaded NLC determined a decrease of occlusion factor and an increase of SPF. No BMTZ release was observed from all emulsions. Sensory attributes were mainly affected by lipid phase ratio. These results suggest that lipid phase ratio and BMTZ incorporation into NLC could contribute to determine technological and sensory properties of O/W emulsions.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

Conventional fertilization practices can lead to many ecological problems, such as nutrient imbalance, soil acidity, and reduced soil fertility in natural rubber plantations. To address these challenges, a field investigation was strategically carried out to substitute inorganic fertilizer with organic fertilizers consisted of six treatments, i.e., no fertilization (CK), inorganic fertilizer (NPK), 25 % replacement of inorganic through organic (25%M), 50 % replacement of inorganic through organic (50%M), 75 % replacement of inorganic through organic (75%M), and 100% organic fertilizer (100%M). The soil physicochemical properties (SOC, TN, AN, C:N, pH, NH4+-N, and NO3--N) and carbon and nitrogen converting enzymes (BG, NAG, and LAP) were all determined. The partial substitution of inorganic fertilizers with organic fertilizers (i.e., 75%M at surface soil layer) showed higher SOC (14.52 g.kg-1), TN (1.06 g.kg-1), AN (20.07 mg.kg-1), C:N (14.63), NH4+-N (10.63 mgkg-1), and NO3--N(11.06 mg.kg-1) than NPK and CK. Such increase in physicochemical properties in partial replacement of inorganic with organic fertilizers plots resulted from higher carbon and nitrogen enzymes activities (BG (143.17 nmol.g-1.h-1), NAG (153.96 nmol.g-1.h-1), and LAP (153.48 nmol.g-1.h-1)) compared to NPK and CK, and further the person correlation and RDA analysis confirmed a significant positive correlation between SOC, AN, and soil enzymes. This study presents a new strategy for assessing the impact of partially replacing inorganic fertilizers with organic fertilizers in rubber plantations, mainly by modifying the soil nutrient composition in tropical regions.

Perilla frutescens leaves are expected to exhibit antioxidant activity and amyloid-β (Aβ) aggregation inhibitory activity due to the presence of polyphenol-type compounds, etc. These activities fluctuate daily; however, measuring the contents of constituents and functionalities is cumbersome and unsuitable for instantaneous measurements in the field. In this study, we developed a facile method to analyze the activity and content of the components in leaves on-site based on the fluorescence spectra obtained by irradiating the perilla leaves with excitation light. The constituent contents (Chlorophyl (Chl), Total polyphenol content (TPC), Total flavonoid content (TFC), rosmarinic acid (RA) and functional properties DPPH radical scavenging activity, ferric reducing antioxidant power (FRAP), oxygen radical absorbance capacity (ORAC), Aβ aggregation inhibitory activity) were evaluated using established analytical techniques. The correlation between the fluorescence spectrum and the contents and activities was calculated using normalized difference spectral index (NDSI), ratio spectral index (RSI), and difference spectral index (DSI) analyses. We identified a predictive model with a high coefficient of determination R² ≥ 0.57 for content of the constituents, and R² ≥ 0.49 for functional properties. This allows convenient, simultaneous, and non-destructive monitoring of the constituent contents and the functionalities of perilla leave and a simple harvest-time diagnosis. The model established using this method is simple and suggesting that it can simultaneously infer the constituents and functionalities of perilla leaves.

The use of unmanned aerial aircrafts (UAVs) is governed by strict regulatory frameworks that prioritize safety. To guarantee safety, it is necessary to acquire and maintain situational awareness (SA) throughout the operation. Existing Canadian regulations require pilots to operate their aircrafts in visual line-of-sight. Therefore, the task of acquiring and maintaining SA primary falls to the pilots. However, the development of aerial transport is entering a new era with the adoption of a highly dynamic and complex system known as advanced air mobility (AAM), which involves UAV operating autonomously beyond visual line-of-sight. SA must therefore be acquired and maintained primarily by each UAV through specific technologies and procedures. In this paper, we review these technologies and procedures in order to decompose the SA of the UAV in the AAM. We then use the system modeling language to provide a high-level structural and behavioral representation of the AAM as a system having UAV as its main entity. In a case study, we analyze one of the flagships UAVs of our industrial partner. Results show that this UAV doesn’t have all the technologies and methodologies necessary to achieve all the identified SA goals identified for the safety of the AAM. This work is a theoretical framework intended to contribute to the realization of the AAM, and we also expect to impact the future design and utilization of UAVs.

Variable and sometimes contrasting effects of using artificial rhizobium inocula to increase grain legume performance have been reported. The objectives of this systematic review and meta-analysis were therefore to (i) estimate the overall effect of rhizobium inocula on grain yield and protein content and (ii) identify potential confounding factors that explain the observed variation. A web of Science database literature search was carried out in 2016. Data from all field experiments, greenhouse and pot experiments that compared grain yields and protein contents in Rhizobium/Bradyrhizobium-inoculated with non-inoculated control crops were extracted and analyzed using previously described unweighted and weighted meta-analysis protocols. GRADE assessments of the strength of evidence of results from the weighted meta-analyses were carried which included an assessment of the risk of publication bias. Results: For unweighted meta-analyses we identified eligible data in 236 and 36 studies for grain yield and protein content respectively. For weighted meta-analyses we identified eligible data in 92 and 8 studies for grain yield and protein content respectively. Rhizobium inoculation was found to (i) significantly increase grain yield in both the unweighted (mean percent difference: 41%, 95%CI 36,46, p<0.0001) and weighted meta-analysis (Standardized mean difference: 1.56, 95%CI 1.26,1.87, p<0.0001) and (ii) significantly increase protein content in the unweighted meta-analysis (mean percent difference: 11%, 95%CI 5,18, p<0.0001), but not the weighed meta-analyses which only detected a trend (0.1>p>0.05) towards higher protein content in inoculated grain legume crops. Multi-level model-based weighted meta-analyses suggest that the (i) type of experiment, (ii) type of fertilizer used in experiments, (iii) grain legume type/species and (iv) the country in which experiments were carried out, were confounding factors. The main limitation of the evidence is that a large number of publications did not report measures of variation and could therefore not be included in the more scientifically sound weighted meta-analyses. However based on the large evidence-base available for grain yield it can be concluded that overall Bradyrhizobium/Rhizobium seed inoculation results can increase grain yield by ~40% compared with non-inoculated grain legume crops.

The Upper Hunter Valley is a major coal mining area in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. The early part of this study identified two air quality subregions in the valley. This paper aims to provide a holistic summarisation of the relationships between elevated PM10 pollution in two subregions and the local- and synoptic-scale meteorological conditions for spring and summer, when PM10 pollution is relatively high. A catalogue of twelve synoptic types and a set of six local meteorological patterns have been quantitatively derived and linked to each other using the self-organising map (SOM) technique. The complex meteorology-air pollution relationships have been visualised/interpretated on the SOM planes for two representative locations. It was found that the influence of local meteorological patterns differed significantly for mean PM10 levels vs the occurrence of elevated pollution events and between air quality subregions. In contrast, synoptic types showed generally similar relationships with mean vs elevated PM10 pollution in the valley. Two local meteorological patterns, the hot-dry-northwesterly wind conditions and the hot-dry-calm conditions, were found most PM10 pollution conducive in the valley when combined with a set of synoptic counterparts. These synoptic types are featured with the influence of eastward migrating continental high pressure system and westerly troughs, or a ridge extending northwest towards coastal northern NSW or southern Queensland from the Tasman Sea. The method and results can be used in air quality research for other locations of NSW, or similar regions elsewhere.

This study investigates the mean annual water temperature trends at the confluence of the Sava and Danube Rivers, along with air temperature trends at the Belgrade meteorological station, spanning from 1956 to 2020. Results reveal a consistent increase in temperature across all three measuring stations, with the Danube experiencing a rise of 0.34°C/10 years, the Sava at 0.44°C/10 years, and Belgrade's air temperature increasing by 0.39°C/10 years. Employing the RAPS method, sharp rises in water temperature were pinpointed in 1989 for the Sava and 1990 for the Danube, while Belgrade's air temperature surge began in 1998. The highest intensity of air temperature increase within the recent period (1998-2020) was observed at the Belgrade observatory, reaching 0.76°C/10 years. Notably, the Sava exhibited a faster increase in water temperature over the last thirty years compared to the Danube. August marked the peak average water temperature for both rivers, while July recorded the highest average air temperature in Belgrade. Despite differing flow rates, both rivers exhibit similar hydrological regimes, with maximum flows occurring in April and minimum flows in August for the Sava, and October for the Danube. Seasonal temperature increases were most pronounced in summer, notably in August, with the smallest rises occurring during cold periods. Additionally, an inverse proportional relationship between mean annual water temperatures and discharges was observed at both river stations.

New flaxseed cultivars differing in seed mucilage content (MC) with low hull content (HC) represent an attractive option to simultaneously target the food and feed markets. Here, a genome-wide association study (GWAS) was conducted for MC and HC in 200 diverse flaxseed accessions genotyped with 1.7 million SNP markers. The data obtained for MC and HC indicated a broad phenotypic variation and high (~70%) and a moderate (~49%) narrow sense heritability, respectively. MC and HC did not differ statistically between fiber and oil morphotypes, but yellow-seeded accessions had 2.7% less HC than brown-seeded ones. The genome wide linkage disequilibrium (LD) decayed to r2 = 0.1 at a physical distance of ~100 Kb. Seven and four QTL were identified for MC and HC, respectively. Promising candidate genes included Linum usitatissimum orthologs of the Arabidopsis thaliana genes TRANSPARENT TESTA 8, SUBTILISIN-LIKE SERINE PROTEASE, GALACTUROSYL TRANSFERASE-LIKE 5, MUCILAGE-MODIFIED 4, AGAMOUS-LIKE MADS-BOX PROTEIN AGL62, GLYCOSYL HYDROLASE FAMILY 17 and UDP-GLUCOSE FLAVONOL 3-O-GLUCOSYLTRANSFERASE that have been shown to play a role in mucilage synthesis and release, seed coat development and anthocyanin biosynthesis in A. thaliana were identified. The favorable alleles will be useful in flaxseed breeding towards the goal of achieving the ideal flaxseed cultivars for food and feed by genomic-based breeding.

Traffic congestion is one of the foremost problems confronted by the urban and suburban tenants of today. Traffic congestion increases vehicle emissions and degrades air quality. Urban planners and policy makers have consequently been always investigating choices to alleviate traffic congestion and to enhance air quality. Teleworking is one option that has received significant consideration and has been studied in the recent past. The aim of the study is to explore the relationship between teleworking, air quality and traffic in Switzerland. The analysis relies on panel individual and household level data over the period 2002-2013. We examine five main air pollutants; the sulphur dioxide (SO₂), the ground-level ozone (O₃) the nitrogen dioxide (NO₂), the carbon monoxide (CO) and the particulate matter less than 10 microns (PM₁₀). Based on the fixed effects estimates, teleworking reduces traffic volume by 1.9 per cent. Furthermore, the reduction observed on air pollution is higher for NO₂, CO and PM₁₀ ranging between 3.3-3.7 per cent, followed by O₃ at 2.3 per cent and SO₂ at 2.1 per cent. According to instrumental variable (IV) approach and the two stage least squares (2SLS) method, the effect is higher ranging between 2.6-4.1 per cent. The respective reduction on traffic becomes 2.7 per cent. Overall, the main concluding remark of the study is that teleworking can be a promising tool for urban planning and development, focusing at the traffic volume reduction, and the air quality improvement. Additional policy implications of teleworking and its beneficial effects for the society are further discussed.

Nowadays, speed up development and use of digital devices such as smartphones have put people at risk of internet crimes. The evidence of present crimes in a computer file can be easily unreachable by changing the prefix of a file or other algorithms. In more complex cases, either file divided into different parts or the parts of a file that has information about the file type are deleted, where the file fragment recognition issue is discussed. The known files are divided into different fragments, and different classification algorithms to solve the problems of file fragment recognition. A confusion matrix measures the accuracy of type recognition. In the present study, first, the file is divided into different fragments. Then, the file fragment features, which are obtained from Binary Frequency Distribution (BFD), are reduced by 2 feature reduction algorithms; Sequential Forward Selection algorithm (SFS) as well as Sequential Floating Forward Selection algorithm (SFFS) to delete sparse features that result in increased accuracy and speed. Finally, the reduced features are given to 3 classifier algorithms, Multilayer Perceptron (MLP), Support Vector Machines (SVM), and K-Nearest Neighbor (KNN) for classification and comparison of the results. In this paper, we proposed the algorithm of file type recognition that can recognize 6 types of useful files ( pdf, txt, jpg, doc, html, exe), which may distinguish a type of file fragments with higher accuracy than the similar works done.

No doubt pollution is a global problem which must be holistically tackled. In doing this, adequate knowledge of the sources of pollution is important, therefore the aim of this paper is to review source apportionment with reference to top-down and bottom-up methods. In this paper, dispersion modeling, emissions inventory, and sampling methods were discussed. Also, analytical methods involved in top-down source apportionment were mentioned. The two techniques are needed to evaluate pollutants and their sources. Based on these two approaches, pollution control strategy would be developed and decisions can be made in deciding the right approach to solve or reduce the pollution problems.

Air pollution is a man-made environmental-related problem and has importance globally among all environmental issues. It is described as an atmospheric situation in which several components appear at high attention above their ambient level and generate a quantifiable effect on vegetation, animals, and people. Air pollution and its control are a universal problem and have become an issue of great trouble for us in current years. However, monitoring and measurement of the concentration of air pollutants are most difficult in assessment to monitoring other components in the environment. Air pollutants are transported to polar regions by different mechanisms such as long-range atmospheric transport or grasshopper effects and via anthropogenic activities. After reaching the polar regions, they settle down and remain as such for a long-time due to their persistent nature. They can distress the environment and wildlife of the polar regions. Generally, dangerous chemicals may cause a risk of well-being effects, whereas lethal pollutants focus on one physiological reaction. We reviewed the available information on air pollution (occurrence, sources, and harmful effects) in the polar regions.

Shenzhen is China’s top ten clean air city and the cleanest air megacity. Even so, epidemiologic studies have shown ambient air pollution had significant adverse impacts on human health in this less polluted city. In this study, the concentrations of six criteria air pollutants (PM2.5, PM10, O3, NO2, SO2, and CO) from 2014 to 2017 were analyzed and compared to thresholds of both national and international air quality standards. The results showed concentrations of all air pollutants were below target values of current national air quality standard, but levels of particulate matter (PM) and O3 were still much higher than the recommended levels by the World Health Organization. Within national air quality standards, the number of over-limit days was rare with few variations between highly polluted and low pollution areas. The air quality improvement was slowing down recently. Our results suggest annual and daily thresholds for PM are too loose for air quality improvement in Shenzhen. Hence, we call for evaluation and establishment of tougher air quality standard.

Understanding the physical properties of ultramafic rocks is important for evaluating awide variety of petrologic models of the oceanic lithosphere, particularly upper mantle and lower crust. Hydration of oceanic peridotites results in increasing serpentine content, which affects lithospheric physical properties and the global bio/geochemical cycles of various elements. In understanding tectonic, magmatic and metamorphic history of the oceanic crust, interpreting seismic velocities, rock composition and elastic moduli are of fundamental importance. In this study we show that as serpentine content increases, density decreases linearly with a slope of 7.85. We also correlate increase in serpentine content with a linear decline in shear, bulk and Young’s moduli with slopes of 0.48, 0.77, 0.45 respectively. Our results show that increase in serpentine content of lower crust and forearc mantle could decrease elasticity of lithospehere and result in break-offs. Therefore tectonic processes at peridotite rich slow spreading ridges may be strongly affected by serpentine content, particularly serpentinization may be responsible for discontinuities in thin crust, and formation of weak fault zones.

The development effect of water flooding in ultra-low permeability reservoir was poor due to its poor physical property and high shale content, the experimental study of air flooding which help to complement producing energy was carried out. Based on the Accelerating Rate Calorimeter experimental results, the crude oil of N block in L oilfield can produce low-temperature oxidation reaction, which was the basic condition of air flooding. Three groups of experiment natural cylinder core were designed for oil displacement, water flooding and air flooding were used respectively, and the relationship of differential pressure, oil recovery, injection capacity with injection volume was investigated. It has been showed on the result that the recovery efficiency improved sharply than water flooding, the effect of depressurization and augmented injection was obvious, and the air displacement was validation.

The ambient air quality data for particulate matter as well as criteria of gaseous pollutants were assembled during December 2013 to December 2015 from the Continuous Air Quality Monitoring Station (CAMS) located at Agrabad, Chittagong. The observation showed that during April- October, 24 hour average concentration of PM10 and PM2.5 were within the National Ambient Air Quality Standard (NAAQS) level but it increased occasionally by more than two and a half times during the whole non-monsoon period (November-March). The highest values found of PM2.5 were 321.1 µg/m³ in January, 2013 and 220.34 µg/m³ in December 2015. Whether, the highest alarming concentration of PM10 was reported as 474 µg/m3 in January 2007. The other gaseous pollutants such as SO₂, NO₂, O₃, CO and Hydrocarbons remain well within the permissible limit except dry non-monsoon period. The yearly average increase of Air Quality Index (AQI) value indicates the growth rate of air pollution in Chittagong city. The main responsible pollutant for air pollution is found PM_2.5.

Walking School Buses (WSBs) provide a safe alternative to being driven to school. Children benefit from the contribution the exercise provides towards their daily exercise target, it gives children practical experience with respect to road safety and helps to relieve traffic congestion around the entrance to their school. Walking routes are designed largely based in road safety considerations, catchment need and the availability of parent support. However, little attention is given to the air pollution exposure experienced by children during their journey to school, despite the commuting microenvironment being an important contributor to a child’s daily air pollution exposure. This study aims to quantify the air pollution exposure experienced by children walking to school and those being driven by car. A school was chosen in Bradford, UK. Three adult participants carried out the journey to and from school each carrying a P-Trak ultrafine particle (UFP) count monitor. One participant travelled the journey to school by car while the other two walked, each on opposite sides of the road for the majority of the journey. Data collection was carried out over a period of two weeks, for a total of five journeys to school in the morning and five on the way home at the end of the school day. Results of the study suggest that car commuters experience lower levels of air pollution dose due to lower exposures and reduced commute times. The largest reductions in exposure for pedestrians can be achieved by avoiding close proximity to traffic queuing up to intersections, and, where possible, walking on the side of the road opposite the traffic, especially during the morning commuting period. Major intersections should also be avoided as they were associated with peak exposures. Steps to ensure that the phasing of lights is optimized to minimize pedestrian waiting time would also help reduce exposures. If possible, busy roads should be avoided altogether. By the careful design of WSB routes, taking into account air pollution, children will be able to experience the benefits that walking to school brings while minimizing their air pollution exposure during their commute to and from school.

This study investigated the effects of exogenous gibberellic acid (GA) treatments (elongating cluster + seedless + expanding, T1; seedless + expanding, T2; expanding, T3 and water, CK) on the content of sugars, organic acids, and endogenous hormones and sink strength.Results showed that T2 treatment displayed the highest fructose and glucose levels at 100 days after treatment (DAT), whereas its effect on tartaric acid, malic acid, and citric acid concentrations at 80 and 100 DAT was relatively weak. Under GA3 treatments, both GA3, IAA, and CTK contents increased, whereas ABA contents decreased at 1, 2, 4, 8, and 48 h. Analysis of sugar phloem unloading revealed that T2 treatment exhibited the highest values during softening and ripening stages. Our findings indicate that appropriate GA3 application can positively influence sink strength by regulating sink size and activity, including berry size enlargement, sugar phloem unloading and sugar accumulation in grape sink cells.

Eye movements support memory encoding by binding distinct elements of the visual world into coherent representations. However, the role of eye movements in memory retrieval is less clear. We propose that eye movements play a functional role in retrieval by reinstating the encoding context. By overtly shifting attention in a manner that broadly recapitulates the spatial locations and temporal order of encoded content, eye movements facilitate access to, and reactivation of, associated details. Such mnemonic gaze reinstatement may be obligatorily recruited when task demands exceed cognitive resources, as is often observed in older adults. We review research linking gaze reinstatement to retrieval, describe the neural integration between the oculomotor and memory systems, and discuss implications for models of oculomotor control, memory, and aging.

Air corridors are an integral part of the advanced air mobility infrastructure. They are the virtual highways in the sky for transportation of people and cargo in the controlled airspace at an altitude of around 1000 ft. to 2000 ft. above the ground level. This paper presents fundamental insights into the design of air corridors with high operational efficiency as well as zero collisions. It begins with the definitions of air cube, skylane or track, intersection, vertiport, gate, and air corridor. Then, a multi-layered air corridor model is proposed. Traffic at intersections is analyzed in detail with examples of vehicles turning in different directions. The concept of capacity of an air corridor is introduced along with the nature of distribution of locations of vehicles in the air corridor and collision probability inside the corridor are discussed. Finally, the results of simulations of traffic flows are presented.

Since electrical resistivity of concrete can be measured in a more rapid and simple way than chloride diffusivity, it should be primarily regular quality control of the electrical resistivity of concrete which provides the basis for indirect of quality control of concrete durability during the concrete construction. If this is realized, the electrical resistivity of concrete can be a crucial parameter to establish maintenance strategy for marine concrete structures. Electrical resistivity of concrete is important to estimate two processes involved in corrosion of reinforcement: initiation (chloride penetration) and propagation (corrosion rate). The resistivity of concrete structure exposed to chloride indicates the risk of early corrosion damage, because a low resistivity is related to rapid chloride penetration and to high corrosion rate. Concrete resistivity is a geometry-independent material property that describes the electrical resistance, which is the ratio between applied voltage and resulting current in a unit cell. The current is carried by ions dissolved in the pore liquid. While some data exist on the relationship between moisture content on electrical resistivity of concrete, very little research has been conducted to evaluate the effect of chloride on the conduction of electricity through concrete. The purpose of this study is to examine and quantify the effect of pore water and chloride content on surface electrical resistivity measurement of concrete. It was obvious that chloride content had influenced the resistivity of concrete and the relationship showed a linear function. That is, concrete with chloride ions had a comparatively lower resistivity. Chloride can lead to underestimate the electrical resistivity of concrete. Conclusively, this paper suggested the quantitative solution to depict the electrical resistivity of concrete with various chloride contents.

This work aims to investigate the effect of catalyst content and reaction time by catalytic upgrading from pyrolysis vapors of residual fat at 450 °C and 1.0 atmosphere, on the yields of reaction products, physicochemical properties (density, kinematic viscosity, refractive index, and acid value) and chemical composition of organic liquid products (OLP), over a catalyst fixed bed reactor, in semi pilot scale. Pellets of Red Mud chemically activated with 1.0 M HCl were used as catalysts. The experiments were carried out at 450 °C and 1.0 atmosphere, using a process schema consisting of a thermal cracking reactor of 2.0 L coupled to a catalyst fixed bed reactor of 53 mL, without catalyst and using 5.0, 7.5, and 10.0% (wt.) Red Mud pellets activated with 1.0 M HCl, in batch mode. Samples of liquid phase products were withdrawn during the course of reaction at 40, 50, 60, 70 and 80 min in order to analyze the process kinetics. The physicochemical properties (density, kinematic viscosity, acid value, and refractive index) of OLP were determined by official methods. The chemical functions present in OLP determined by FT-IR and the chemical composition by GC-MS. The thermal catalytic cracking of residual fat show OLP yields from 54.4 to 84.88 (wt.%), aqueous phase yields between 2.21 and 2.80 (wt.%), solid phase yields (coke) between 1.30 and 8.60 (wt.%), and gas yields from 11.61 to 34.22 (wt.%). The yields of OLP increases with increasing catalyst content while those of aqueous, gaseous and solid phase decreases. For all the thermal and thermal catalytic cracking experiments, the density, kinematic viscosity, and acid value of OLP decreases with increasing reaction time. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, cycloalkanes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, and aldehydes). For all the thermal and thermal catalytic cracking experiments, the hydrocarbon content within OLP increases with reaction time, while those of oxygenates decrease, reaching concentrations of hydrocarbons up to 95.35% (area.). The best results for the physicochemical properties (density, kinematic viscosity, and acid value) and the maximum hydrocarbon content of OLP were obtained at 450 °C and 1.0 atmosphere, using a catalyst fixed bed reactor, with 5.0% (wt.) Red Mud pellets activated with 1.0 M HCl as catalyst.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

The interest in flying wings dates as far the early years of the aviation age. Over the 20th century, numerous attempts were made to investigate the feasibility of the concept, which demonstrated numerous early benefits: increased aerodynamic efficiency, reduced fuel consumption and lower noise and pollutant emissions compared to conventional tube and wing aircraft. However, major technical challenges prevented that type of design from entering mass production, especially with regards to structural design and manufacturing, stability and control and ride quality. In the 1990’s, a new concept, the blended wing body (BWB), was created to alleviate some of the concerns of flying wings while maintaining increased efficiency. Despite the promise, technical hurdles once again proved to be a deal breaker, and as of 2024, the only flying wing to enter serial production is the B-2 Spirit, an extremely complex and expensive aircraft. Thirty years later, as the world is quickly transitioning towards cleaner energy, the interest in the blended wing body has been renewed. The latest technological advancements in the aerospace industry should make the development of the BWB more plausible, however passenger comfort issues remain. Surprisingly, the BWB development may come from an unexpected application: as a tanker aircraft. As the U.S. Air Force is seeking a replacement to hundreds of aging tankers, a startup company was recently funded to develop the concept and build a prototype. In this study, we explore the history of blended designs from its early days, highlighting its opportunities and challenges – and why the design is an intriguing fit for application as a tanker aircraft.

This comprehensive critical review shows how green buildings and energy optimization solutions improve indoor air quality as well as environmental quality (IEQ) and human health. Electricity-efficient green buildings create a better indoor atmosphere and save electricity. Green buildings improve occupant well-being through IAQ, thermal comfort, acoustics, and lighting. Renewable energy, green construction materials, and intelligent technologies increase sustainability and reduce environmental impact. Environmental hazards, architectural design, and societal variables can improve indoor air quality and subsequently reduce health risks linked with poor air quality. The evaluation highlights the pros and cons of low-cost IAQ sensors and equipment. These devices provide valuable insights, but calibration and validation using reference equipment are necessary to ensure accuracy and reliability. Architects, engineers, environmentalists, and policymakers are essential in creating green buildings with high IEQ. Prioritizing occupant comfort, health, and productivity ensures a sustainable and healthy future for future generations. However, continual monitoring and research are needed to improve green building practices and overcome construction problems. Intelligent models for continual on-field calibration of low-cost sensors may improve performance. Green buildings benefit occupants and the environment by optimizing energy use and using IAQ monitoring technologies.

This article examines air sampling as an environmental surveillance strategy for early pathogen detection and offers a preliminary comparison of air and wastewater surveillance. Air sampling involves collecting bioaerosols to analyze the microbial composition of the air, utilizing techniques like PCR and metagenomic sequencing. Air sampling appears especially promising for detecting respiratory pathogens and highly transmissible pandemic agents, as these spread primarily via aerosols and droplets. The article details various air sampling techniques, their efficiency, and practical considerations, categorizing them into filtration, impaction, impingement, electrostatic precipitation, and condensation methods. It also explores the composition of airborne microbes, emphasizing the low concentration of viral nucleic acids and the challenges this poses for metagenomic sequencing. The selection of sampling locations, including indoor environments and airplanes, is discussed as critical for effective pathogen detection. Finally, the article contrasts air and wastewater sampling, concluding that while both methods should ideally be explored as layered defenses, air sampling does not collectively appear more promising than wastewater sampling.

Urban air quality is increasingly becoming a cause for concern for the health of the human population. The poor air quality is already wreaking havoc in major cities of the world, where serious health issues and reduction of average human life by a factor of years are reported. The air quality in developing countries can become worse as they undergo development. The urban air quality varies non-linearly depending upon the various factors such as land use, industrialization, waste disposal, traffic volume, etc. To address this problem, it is necessary to look at the plethora of available literature from multiple perspectives such as types and sources of pollutants, meteorology, urban mobility, urban planning and development, health care, economics, etc. In this paper, we provide a comprehensive survey of the state-of-the-art in urban air quality. We first review the fundamental background on air quality and present the emerging landscape of urban air quality. We then explore the available literature from multiple urban air quality measurement projects and provides the insights uncovered in them. We then take a look at the sources that are significantly contributing to polluting the air quality. Finally, we highlight open issues and research challenges in dealing with urban air pollution.

Environment pollution is the major problem for all the sectors. In environment pollution there are different types of pollution is included such as air pollution, water pollution, soil pollution etc. In these types of pollution most of it is air pollution. There are many reasons for pollution of air. Human advance in science but one of the major draw backs of science is the pollution of air rapidly. Air pollution is injurious to health. Every year a large number of people died for the effects of air pollution. It can be improved in many ways among these ways technology upgradation plays a major role here. There are various method that prevent air pollution. Many researchers tried and is trying to prevent the air pollution in many ways. In this review paper I summarise the existing research on different ways for preventing air pollution in addition I will discuss the gaps and future aspect on this topic.

Pyrolysis is a combustion process of woody biomass conducted under low or no oxygen conditions. New innovations and the need to limit open burning has resulted in numerous mobile and fixed plant pyrolysis methods that burn a variety of woody residues. Production technologies that reduce the need for open burning, the main source of potential pollutants, fall under the regulations in the Clean Air Act of 1990. This Act is the legal instrument to regulate air pollution at its source across the United States of America and it is implemented and enforced through the Environmental Protection Agency, in coordination with sister agencies. One newer innovation for reducing woody residues and emissions is an air curtain incinerator. Currently, the Clean Air Act regulates stationary solid waste incinerators, and this is also applied to mobile air curtain incinerators burning woody biomass. However, other woody biochar production methods (e.g., flame cap kilns) are not subject to these regulations. Discrepancies in the interpretation of definitions related to incineration and pyrolysis and the myriad of differences related to stationary and mobile air curtain incinerators, type of waste wood from construction activities, forest residues, and other types of clean wood make the permitting regulations confusing as permits can vary by jurisdiction. This review summarizes the current policies, regulations, and directives related to in-woods biochar production and the required permits.

In this work, a novel heterojunction based on ZnSnO3/ZnO nanofibers was prepared using electrospinning method. The crystal, structural and surface compositional properties of sample based on ZnSnO3 and ZnSnO3/ZnO composite nanofibers were investigated by X-ray diffractometer (XRD), Scanning electron microscope (SEM), X-ray photoelectron spectrometer (XPS) and Brunauer-Emmett-Teller (BET). Compared to pure ZnSnO3 nanofibers, the ZnSnO3/ZnO heterostructure nanofibers display high sensitivity and selectivity response with fast response towards ethanol gas at low operational temperature. The sensitivity response of sensor based on ZnSnO3/ZnO composite nanofibers were 19.6 towards 50 ppm ethanol gas at 225°C, which was about 1.5 times superior than that of pure ZnSnO3 nanofibers, which can be owed mainly to the presence of oxygen vacancies and the synergistic effect between ZnSnO3 and ZnO.

In this study, the relationship between air diffusivity and permeability in cementitious materials was investigated. First, we derived an equation to correlate air diffusivity and permeability in a straight circular tube. Then, we reviewed existing studies that measured both air diffusivity and permeability and compared reported data and calculated values to verify the applicability of the derived equation to cementitious materials. Although a correction factor was not used, the two sets of data showed good agreement quantitatively. This indicates that the derived equation can be applied to cementitious materials including concrete, and measured air diffusivity can be converted to permeability of concrete and vice versa using the derived equation.

This paper investigates the effects of air void topology on hydraulic conductivity in asphalt mixtures with porosity in the range 14%-31%. Virtual asphalt pore networks were generated using the Intersected Stacked Air voids (ISA) method, with its parameters being automatically adjusted by the means of a differential evolution optimisation algorithm, and then 3D printed using transparent resin. Permeability tests were conducted on the resin samples to understand the effects of pore topology on hydraulic conductivity. Moreover, the pore networks generated virtually were compared to real asphalt pore networks captured via X-ray Computed Tomography (CT) scans. The optimised ISA method was able to generate realistic 3D pore networks corresponding to those seen in asphalt mixtures in term of visual, topological, statistical and air void shape properties. It was found that, in the range of porous asphalt materials investigated in this research, the high dispersion in hydraulic conductivity at constant air void content is a function of the average air void diameter. Finally, the relationship between average void diameter and the maximum aggregate size and gradation in porous asphalt materials was investigated.

The objective of this study was to assess the effects of parity and lactation stage on the content and conversion rate of DHA in milk from dairy cows fed ruminally protected algae powder. A total of 800 cows were blocked by parity and divided into eight groups (n = 100, three groups of primiparous cows and five groups of multiparous cows) in a six-month experimental period. The lactation period was divided into three stages: 16 – 100 d, 101 – 200 d, and 201–305 d. All cows were fed 100 g of DHA-rich algae powder twice a day, with the DHA content > 13%. Milk samples were collected monthly, and daily milk yield and dry matter intake were recorded. Using infrared spectroscopy, we determined the content of protein, fat, lactose, and total solids in milk and calculated the DHA conversion rate. The results showed that parity and lactation stage had no significant effects on milk composition. However, milk yield and dry matter intake were higher in multiparous cows than in primiparous cows. The DHA content and conversion rate in milk were not significantly different between parity groups but were positively correlated with lactation stage and negatively correlated with milk fat content.

Optical sensor data can be used to determine changes in anthocyanins, chlorophyll and soluble solids content (SSC) in apple production. In this study, visible and near-infrared spectra (729 to 975 nm) were transformed to SSC values by advanced multivariate calibration models i.e. partial least square regression (PLSR) in order to test the substitution of destructive chemical analyses through non-destructive optical measurements. Spectral field scans were carried out from 2016 to 2018 on marked ’Braeburn’ apples in Southwest Germany. The study combines an in-depth statistical analyses of longitudinal SSC values with horticultural knowledge to set guidelines for further applied use of SSC predictions in the orchard to gain insights into apple carbohydrate physiology. The PLSR models were investigated with respect to sample size, seasonal variation, laboratory errors and the explanatory power of PLSR models when applied to independent samples. As a result of Monte Carlo simulations, PLSR modelled SSC only depended to a minor extent on the absolute number and accuracy of the wet chemistry laboratory calibration measurements. The comparison between non-destructive SSC determinations in the orchard with standard destructive lab testing at harvest on an independent sample showed mean differences of 0.5 % SSC over all study years. SSC modelling with longitudinal linear mixed-effect (LME) models linked high crop loads to lower SSC values at harvest and higher SSC values for fruit from the top part of a tree.

Implementation of waterflood is with injected pressured water to reservoir to escalation oil production. Produced water is the dominated result from oil and gas mechanism in this world meanwhile 65% of water is injected back to the well for pressure maintenance, 30% for discharge aquifier condition and surface. For shaly sand, produced water usually bring coarse and suspended sand to the surface. Therefore, this sand level is needed to declining to avoid plugging in injection well until certain economic condition.

International literature data report that the increase of infectious risk may be due to heating, ventilation and air conditioning (HVAC) systems contaminated by airborne pathogens. Moreover, the presence of complex rotating dehumidification wheels (RDWs) may complicate the cleaning and disinfection procedures of the HVAC systems. We evaluated the efficacy of a disinfection strategy applied to the RDW of two hospitals HVAC systems. Hospitals have 4 RDW systems related to the surgical areas (SA1 and SA2) and to the intensive and sub-intensive cares (IC and sIC). Microbiological air and surfaces analysis were performed in HVAC systems, before and after the disinfection treatment. Hydrogen peroxide (12%) with silver ions (10 mg/L) was aerosolized in all the air sampling points, located close to the RDW device. After the air disinfection procedure, reductions of total microbial counts at 22°C and fungi were achieved in SA2 and IC HVAC systems. An Aspergillus fumigatus contamination (6 CFU/500L), detected in one air sample collected in the IC HVAC system, was eradicated after the disinfection. Surface samples proved a good microbiological quality. Results suggest the need of a disinfection procedure aimed to improve the microbiological quality of the complex HVAC systems, mostly in surgical and intensive care areas.

In the literature, the chemical composition of Rhododendron tomentosum is mainly represented by the study of isoprenoid compounds of essential oil. In contrast, the study of the content of flavonoids will contribute to the expansion of the pharmacological action and the use of the medicinal plant for medical purposes. The paper deals with the technology of extracts from Rhododendron tomentosum shoots using ethanol of various concentrations and purified water as an extractant. Extracts from Rhododendron tomentosum were obtained by a modified method that combined the effects of ultrasound and temperature to maximize the extraction of biologically active substances from the raw material. By the method of high-performance thin-layer chromatography in the system of solvents ethyl acetate: formic acid: water (15:1:1) the following substances have been separated and identified: rutin, hyperoside, quercetin, and chlorogenic acid in all the extracts obtained. To quantify the total flavonoids content, a method of spectrophotometric determination based on the reaction of complexation with aluminum chloride has been developed. It has been proved that the course of the complexation reaction and, accordingly, the quantification of the flavonoid structure substances by the spectrophotometric method is influenced by some factors, including the environment, pH, the structure of the complexes, etc. Regardless of the chosen method, for the further production of Rhododendron tomentosum extracts with a higher content of flavonoid structure substance, it is advisable to use 60%, 70%, and 80% ethyl alcohol as extractant.

Every (multimedia) service needs to be accessible. Accessibility for multimedia content is typically provided by means of access services, of which subtitling is likely the most widespread one. Up to date, many recommendations and solutions for subtitling classical 2D audiovisual services are available. Likewise, recent efforts have been devoted to devising adequate subtitling solutions for VR360 video content. This paper, for the first time, goes a step beyond, by exploring two key requirements to fulfill remaining challenges towards efficiently subtitling 3D Virtual Reality (VR) content: presentation modes, and guiding methods. By leveraging insights from earlier work on VR360 content, the paper proposes novel presentation modes and guiding methods to not only deal with the freedom to explore the omnidirectional scenes, but also with additional specificities of 3D VR compared to VR360 content: depth, 6 Degrees of Freedom (6DoF), and viewing perspectives. The obtained results prove that always-visible and a novel proposed comic-style presentation mode are far more appropriate than state-of-the-art fixed-positioned subtitles, mainly in terms of immersion, ease and comfort of reading, and identification of speakers, when applied to professional pieces of content with limited displacement of speakers and with limited 6DoF (i.e. users are not expected to largely navigate around the virtual environment). Likewise, even in such limited movement scenarios, the results show that the use of indicators (arrows), as guiding methods, is well received. Overall, the paper provides relevant insights and paves the way toward efficiently subtitling 3D VR content.

Dietary supplements are more and more often used to increase daily intake of essential vitamins and minerals. These preparations are classified as special category of foods and are subject to food law, not pharmaceutical regulations. As a result the requirements to dietary supplements are much less restrictive than to medications. Also simple and inexpensive procedure of registration causes that the number of dietary supplements is widely spread every year. On every manufacturing phases of dietary supplements, there is a risk of contamination. One of the pollutions might be mercury which is classified as heavy metal. Its inorganic compounds damage kidneys and liver and methylmercury is easily absorbed from gastrointestinal system. Methylmercury is distributed in all tissues, also in nervous system. The aim of study was to determine the level of mercury in multivitamins and multiminerals preparations and to analyze the results. The study included 22 dietary supplements containing vitamins and minerals available on Polish market. Mercury was analyzed with atomic absorption spectrometry using AMA 254. The concentrations of Hg was 0.22–5.85 µg/kg (the average content was 2.40 µg/kg). The highest average mercury content was 4.51 µg/kg, whereas the lowest one was 0.31 µg/kg. The results was also analyzed in individual groups depending on main component and indication for use as well as pharmaceutical formulation. Also according to manufacturer’s recommendation, the dose of mercury taken with a single medicine was estimated for time of a day, a week, a month, 3 months and also a year. The findings were compared to limits defined in regulations of European Union and PTWI set by JECFA to assess the health risk. The results presented in this study proved that the amount of mercury in tested dietary supplements is much lower than the value of valid regulations. Analyzed supplements as long as they are used with the recommendation of manufacturer, do not pose a threat to human health.

The lipid fraction of margarines and fast-food French-fries, two types of foods traditionally high in trans fatty acids (TFA), is assessed. TFA data reported worldwide during the last 20 years have been gathered, and show that some countries still report high TFA amounts in these products. The content of TFA was analysed in margarines (2 store and 4 premium brands) and French-fries from fast-food restaurants (5 chains). Margarines showed mean values of 0.68% and 0.43% (gTFA/100g fat) for store and premium brands, respectively. French-fries values ranged from 0.49% to 0.89%. All samples were lower than the 2% set by some European countries as the maximum legal content of TFA in fats, and contained less than 0.5g/serving, so they could also be considered “trans free products”. This work confirmed that the presence of TFA is not significant in the two analysed products and contributes to update food composition tables, key tools for epidemiological and nutrition studies.

: During the period of COVID-19, the Chinese government implemented a series of actions to prevent the spread of the virus. It is noticed that these preventive actions have generated positive effects on air pollution in Wuhan and Beijing. And, due to the differences in city functions, geographic locations, meteorological conditions, and preventive action details between the two cities, noticeable difference is observed on how they reduced air pollution. This unfortunate incident has become a social sample for studying the industrial and livelihood activities impact on air pollution, otherwise would be highly impossible. This paper starts from observing data from NASA's real-time fine particulate matter (PM2.5) and NO2, and comparing the air pollution in this special time domain with previous years. It is discovered that both PM2.5 and NO2 have been reduced in Wuhan, while only NO2 has significant reduction in Beijing, during the COVID-19 responses. This suggests that the human activity suppression by the COVID-19 control yields different effects on different pollutants and in different cities. Possible reasons for such effects are analysed by considering the public health control levels as well as the pollutant migration, industrial activities, and the weather conditions.

Alzheimer´s disease (AD) is characterized by the brain deposition of senile plaques composed by amyloid-β peptides (Aβ) that increase inflammation. An endogenous peptide derived from the insulin-like growth factor (IGF)-I, glycine-proline-glutamate (GPE) has IGF-I-sensitizing and neuroprotective actions. Here, we examined the effects of GPE on Aβ levels and hippocampal inflammation generated by the intracerebroventricular infusion of Aβ25-35 during 2 weeks (300 pmol/day) in ovariectomized rats and the signaling-related pathways and levels of Aβ-degrading enzymes associated with these GPE-related effects. GPE prevented the Aβ-induced increase in the phosphorylation of p38 mitogen-activated protein kinase and the reduction in activation of signal transducer and activator of transcription 3, insulin receptor substrate-1 and Akt, as well as on interleukin (IL)-2 and IL-13 levels in the hippocampus. The functionality of somatostatin, measured as the percentage of inhibition of adenylate cyclase activity and the levels of insulin-degrading enzyme were also preserved by GPE co-treatment. These findings indicate that GPE co-administration may protect from Aβ insult by changing hippocampal cytokine content and somatostatin functionality through regulation of leptin- and IGF-I-signaling pathways that could influence the reduction in Aβ levels through modulation of levels and/or activity of Aβ proteases.

Mental wellness can be related to healthier living, the learning process and working environments for people in the university community. A wide range of mental wellness programmes have been explored to provide students with pleasant and satisfying experiences. The purpose of this study is to explore the effects of integrating Zen meditation(禪)and music listening on the mindfulness and happiness levels of university music therapy students. Qualitative methodology was used, and data were collected through surveys and semi-structured interviews. To investigate various aspects of data regarding the role of meditation and music (MM) programme for mindfulness and happiness, this study used thematic analysis within a qualitative research design. The results of this study indicate that the 8-week MM programme is effective in enhancing mindfulness and happiness and has positive responses to daily life stress (e.g., exam anxiety, financial difficulties, and emotional distress during the COVID-19 pandemic). The role of meditation and music in promoting mental health and well-being has long been discussed and the combination of the two has been recognised as a beneficial intervention. This paper could contribute to the support of mental health resources and coping strategies in higher education, as well as expand the potential range of integrating practices involving music and meditation.

The aim of the study was to determine the maximum safe concentration of calcium and phosphate in neonatal parenteral nutrition (PN) solutions when various combinations of inorganic and organic salts are applied. Twelve PN solutions for neonatal use were aseptically prepared. Increasing concentration of inorganic and organic calcium and phosphate were added to the standard formulas. Each admixture was separately tested according to following conditions; after mixing, 37°C for 24 h, and maximum safe combination of calcium and phosphate were stored at 4°C for 30 days and followed by 24 h at 37°C. Visual inspections against a black and white contrast background, microscopic observation of undiluted PN solutions as well as the membrane filter after filtration of the PN solution, pH evaluation, and spectrophotometry at 600 nm were examined in triplicate. Safe maximum concentration of organic and inorganic calcium and phosphate was proposed individually for each composition of parenteral nutrition solutions. Surprisingly organic calcium with organic phosphate showed precipitation but over the therapeutic range. The protective effect of amino acid was observed and higher concentrations of calcium and phosphate were free of precipitation.

This work investigates spatial and temporal distributions of hydroxyl, OH, in laser-plasma in laboratory air at standard ambient temperature and pressure. Of interest are determination of temperature and density of OH and establishment of a correlation of molecular OH emission spectra with shadow graphs for time delays of 50 to 100 microsecond, analogous to previous work on shadow graph and emission spectroscopy correlation for cynaide, CN, in gas mixtures and for time delays of the order of 1 microsecond. Wavelength- and sensitivity- corrected spatiotemporal data analysis focuses on temperature inferences using molecular OH emission spectroscopy. Near-ir radiation from a Q-switched laser device initiates optical breakdown in laboratory air. The laser device provides 6 nanosecond, up to 850 milli Joule pulses at a wavelength of 1064 nanometer, and focal irradiance in the range of 1 to 10 Tera Watt per centimeter-squared. Frequency doubled beams are utilized for capturing shadow graphs for visualization of the breakdown kernel at time delays in the range of 0.1 to 100 microsecond. OH emission spectra of the laser plasma, spatially resolved along the slit dimension, are recorded in the wavelength range of 298 nm to 321 nm, and with gate widths adjusted to 10 microsecond for the intensified charge-coupled device that is mounted at the exit plane of a 0.64 m Czerny-Turner configuration spectrometer. Diatomic OH signals occur due to recombination of the plasma and are clearly distinguishable for time delays larger than 50 microsecond, but are masked by spectra of N2 early in the plasma decay.

We describe a novel machine that uses the greater-than-100% efficiency of air/ground-source heat pumps to recursively generate electricity via steam-powered generators, taking thermal energy from the ambient environment to convert into electrical power. The invention of a machines that generate clean power at low costs will be fundamental to the future of electricity. We estimate efficiency and calculate minimum efficiencies for unknown parts to consider the applicability of this machine to the real world.

Growing popularity of buildings with integrated sub-systems, requires a review of methods to optimize the preheat of ventilation air. An integrated system permits using geothermal heat storage parallel to the direct outdoor air intake with additional treatment in the mechanical room as a part of building automatic control system. Earth Air Heat Exchanger (EAHX) has many advantages but also has many unanswered questions. Some of the drawbacks are: a possible entry of radon gas, high humidity in the shoulder seasons as well as the need for two different air intake sources with a choice that depends on the actual weather conditions. While in winter, the EAHX may be used continuously to ensure thermal comfort, in other seasons, its operation must be automatically controlled. To generate the missing information about the EAHX technology we have examined two nearly identical EAHX systems, one placed in ground next to the building and the other under the basement slab. In another project, we have reinforced the ground storage action by heat exchanger placed on the return pipes of the hydronic heating system. Effectively, the information provided in this paper, shows advantages of merging both these approaches while the EAHX could be placed under the house or near the basement foundation that is using an exterior basement insulation.

Growing popularity of smart and integrated buildings requires a review of methods to optimize the preheat of ventilation air. An integrated system permits using heat ex-changers located in the mechanical room or in the future even using an exterior wall as a heat exchanger. One may ask the question how does the earth-air heat exchanger (EAHX) technology fitts into this function. EAHX has many advantages but also has many unanswered questions. Some of the drawbacks are: a possible entry of radon gas, high humidity in the shoulder seasons as well as the need for two different air intake sources with a choice that depends on the actual weather conditions. While in winter, the EAHX may be used continuously to ensure thermal comfort, in other seasons, its operation must be automatically controlled. To generate the missing information about the EAHX technology we reviewed literature and examined two nearly identical EAHX systems, placed either in ground next to the building or under the basement slab. Effectively, the information provided in this paper, shows advantages of merging both these approaches while the EAHX shoud be placed under the house or near the basement foundation.

Abstract: The air pollution dispersion modelling via spatial analyses (Land Use Regression – LUR) is an alternative approach to the air quality assessment to the standard air pollution dispersion modelling techniques. Its advantages are mainly much simpler mathematical apparatus, quicker and simpler calculations and a possibility to incorporate other factors affecting pollutant’s concentration. The goal of the study was to model the PM10 particles dispersion modelling via spatial analyses v in Czech-Polish border area of Upper Silesian industrial agglomeration and compare results with results of the standard Gaussian dispersion model SYMOS’97. Results show that standard Gaussian model with the same data as the LUR model gives better results (determination coefficient 71% for Gaussian model to 48% for LUR model). When factors of the land cover and were included into the LUR model, the LUR model results were significantly improved (65% determination coefficient) to the level comparable with Gaussian model. The hybrid approach combining the Gaussian model with the LUR gives superior quality of results (65% determination coefficient).

Air pollution knows no boundaries, which means for a city or a region to attain clean air standards, must not only look at the emission sources within its own administrative boundary, but also at sources in the immediate vicinity and those originating from long-range transport. And there is a limit to how much area can be explored to evaluate, govern, and manage as designated airsheds for cities and larger regions. This paper discusses the need from an official airshed framework for India’s air quality management, urban airsheds designated for India’s 131 non-attainment cities under the national clean air programme, and proposes climatically and geographically appropriate regional airsheds to support long-term planning. Between 28 states, eight union territories, 36 meteorological sub-regional divisions, and six regional meteorological departments, establishing the proposed 15 regional airsheds for integrated and collaborative air quality management across India is a unique opportunity.

The educational and play-related activities of children are proceeded mainly indoors in a kin-dergarten. The exposure of children to high concentrations of PM2.5 and CO2 indoors have leaded to various harmful effects and negatively impact educational outcomes in a kindergarten. Therefore, this study presents a numerical model of CO2 and PM2.5 concentration based on two classrooms in a kindergarten. Using this numerical model, we present different scenarios of oper-ating mechanical ventilation and air purifiers in kindergartens with the aim of optimizing for reducing the concentrations of CO2 and PM2.5. We found that the amount of ventilation required to maintain good air quality, per child, was approximately 20.4 m3/h. However, we also found that as the amount of ventilation increased, so did the concentration of indoor PM2.5; we found that this issue can be resolved through the use of a high-grade filter (i.e., a MERV 13 grade filter with a collection efficiency of 75%). This study provides a scientific basis for reducing PM2.5concentrations in kindergartens, while keeping CO2 levels low.

This study proposes an image recognition method to assist swine farm managers in collecting health data related to pig feeding and excretion. Analyzing the correlation between sow health data and indoor air quality in the pigsties revealed significant influences of air quality indicators on sow health. Increased levels of TVOC, CO2, and temperature were found to negatively affect feeding health, while increased temperature, humidity, and PM10 were found to negatively impact excretion health. These findings provide a basis for evaluating variables when constructing future sow disease prediction models. Analyzing the correlation between pig health status and air quality can help swine farm managers improve sow production environments, reduce disease risks, enhance production efficiency, and provide valuable insights for future research on disease prediction models.

Multiple social and environmental justice concerns are linked to urban form such as the distribution of socioeconomic class populations, healthcare spending, air pollution exposure, and human mobility. This study used 1m resolved LIDAR data to characterize land use in Salt Lake County, Utah and associate it with sociodemographic and air quality data at the census block group and zip code levels. We found that increasing tree cover was associated with higher per capita income and lower minority populations while increasing built cover was linked to lower per capita income and higher minority populations. Air quality showed less strong correlations, however, decreased non irrigated cover, increased built cover, and higher amounts of households living under poverty was related to higher long-term PM2.5 exposure. Several policy efforts have been undertaken to improve air quality and reduce negative health outcomes in Utah which are being informed by regulatory and research grade air quality sensors.

This research uses the computing of conceptual distance to measure information content in Wikipedia categories. The proposed metric, generality, relates information content to conceptual distance by determining the ratio of information a concept provides to others compared to the information it receives. The DIS-C algorithm calculates generality values for each concept, considering each relationship's conceptual distance and distance weight. The findings of this study were compared to current methods in the field and found to be comparable to results obtained using the WordNet corpus. This method offers a new approach to measuring information content applied to any relationship or topology in conceptualization.

Water plays a crucial role in maintaining plant functionality and drives many ecophysiological processes. The distribution of water resources is in a continuous change due to global warming affecting the productivity of ecosystems around the globe, but there is a lack of non-destructive methods capable of continuous monitoring of plant and leaf water content that would help us in understanding the consequences of the redistribution of water. We studied the utilization of novel small hyperspectral sensors in the 1350-2450 nm spectral range in non-destructive estimation of leaf water content in laboratory and field conditions. We found that the sensors captured up to 96% of the variation in equivalent water thickness (EWT, g/m²) and up to 90% of the variation in relative water content (RWC). These laboratory findings were supported by field measurements, where repeated leaf spectra measurements were in good agreement (R²=0.79) with a time-lagged change of tree xylem diameter. Further tests were done with an indoor plant (Dracaena marginate Lem.) by continuously measuring leaf spectra while drought conditions developed, which revealed detailed diurnal dynamics of leaf water content. We conclude that close-range hyperspectral spectroscopy can provide a novel tool for continuous measurement of leaf water content at the single leaf level and help us to better understand plant responses to varying environmental conditions.

Carbon capture and storage has gotten increased attention during the last decade, and several full-scale projects are currently being planned. This requires transportation of large quantities of CO2 from the capturing plant to the end point. From economic and public acceptance point of view it is important to ensure that the transportation system is operated in a safe manner. Thus, avoiding threats like corrosion or formation of particles are important. It is therefore required to monitor that the transported CO2 fulfils the required specifications, and in practice this means that the impurity content of the CO2 must be analysed. CO2 will in most cases be transported in the liquid or supercritical state (high pressure), which makes the practicalities around chemical analysis more difficult. Phase transition from liquid or supercritical state to gaseous state may also introduce several physiochemical effects that may affect the analysis. This paper discusses technical and practical challenges with such types of analysis. Most of this work is based on experience that was gained during development of analytical system for dense phase CO2 in a joint industry project that studied corrosion and chemical reactions in a simulated CO2 transport system.

The importance of detecting bacteria in various food products is ever-increasing, due to recent food trends that lend themselves to food contamination. Additionally, the detection of probiotics in food products is of increasing importance to consumers, who realize the benefits of probiotics on one’s diet. Existing technologies for detection of bacteria in food are accurate, but most are slow, increasingly costly and unsuitable for applications outside of research laboratories. Optic approaches have recently emerged as an alternative, allowing rapid detection of bacterial presence. This study employs a portable kinetics fluorometer, fabricated in-house, in conjunction with NADH sensitive fluorescence reporter for analysis of various food products. The presence of bacteria is detected in 5 minutes. Both pathogenic and probiotic bacteria were detected in food products, such as raw chicken and beef, spoiled lettuce and contaminated water, yogurt, and kombucha tea. The cellular activity of two probiotic pills was also verified. All samples displayed varying levels of bacterial activity. The study indicates the viability of biosensors being used as an alternate method to detect bacteria in food products – and the viability of a fluorescence-based biosensor to detect viable bacteria. The approach is suitable for both laboratory and field determinations.

1) Background: the budget of non-thermal energy in galaxy clusters is not well constrained, owing to the observational and theoretical difficulties in studying these diluted plasmas on large scales. 2) Method: we use recent cosmological simulations with complex physics in order to connect the emergence of non-thermal energy to the underlying evolution of gas and dark matter. 3) Results: the impact of non-thermal energy (e.g. cosmic rays, magnetic fields and turbulent motions) is found to increase in the outer region of galaxy clusters. Within numerical and theoretical uncertainties, turbulent motions dominate the budget of non-thermal energy in most of the cosmic volume. 4) Conclusion: assessing the distribution non-thermal energy in galaxy clusters is crucial to perform high-precision cosmology in the future. Constraining the level of non-thermal energy in cluster outskirts will improve our understanding of the acceleration of relativistic particles by cosmic shocks and of the origin of extragalactic magnetic fields.

According to their nutritional value, their ability to adapt to the various environmental conditions, and their versatility, cereals are among the most cultivated plants in the world. However, the ongoing climate changes subject crops to important environmental stress that for some varieties leads to high production losses. Therefore, selection of species and varieties more versatile and adaptable to different environmental conditions can be important. However, the characteristics of some cereals are not completely known, this is a priority before to improve their cultivation. The aim of this study is to characterize select species of potential suitable for local environmental conditions, nutritional value.

The moisture content of maize seed is an important indicator for evaluating seed quality and a fundamental item in grain testing. The experiment used direct drying method to measure the moisture content of 80 different varieties of maize samples, and captured their images using a hyperspectral imaging (HSI) system in the spectral range of 1100~2498nm. By comparing seven spectral preprocessing methods, the PLSR model established after Normalize pretreatment had the best effect. The characteristic wavelengths were selected by Successive Projections Algorithm (SPA), Competitive Adaptive Reweighted Sampling (CARS) and Uninformative Variable Elimination (UVE). Twelve prediction models were established for full band spectra and characteristic wavelengths based on PLSR, PCR and SVM. By comparing the performance of the prediction models, it was found the Normalize-SPA-PLSR algorithm was optimized. The values of RC2 and RP2 in the model were higher, which were 0.9936 and 0.9933, respectively, while the values of RMSEP and RMSECV were lower, which were 0.0357 and 0.0380, respectively. The Normalize-SPA-PLSR model was used as a visual prediction model for moisture content of maize seed, the 20 maize varieties in the prediction set were visualized to obtain visualized color images of moisture content. The color differences between different moisture content images were significant. The result indicated that hyperspectral imaging could accurately, rapidly, and non-destructive predict moisture content of maize seed, which provided technical support for moisture content detection in the process of maize harvest, storage and processing.

In recent years, there has been an increasing demand for personalized experiences in various domains, including the cultural and educational sectors. Museums, as custodians of art, history, and scientific knowledge, are seeking innovative ways to engage their visitors and provide tailored content that enhances their understanding and appreciation of the exhibits. This article presents ExhibitXplorer, a distributed architecture service that leverages geofencing, artificial intelligence, and microservices to enable personalized content delivery in museums. By combining implicit and explicit segmentation of museum visitors and utilizing the GPT API for content generation, ExhibitXplorer offers a dynamic experience to different visitor segments, including researchers, students, casual visitors, and children. The system utilizes push notifications triggered by visitor location changes, allowing seamless delivery of personalized information both indoors and outdoors. Tests were conducted to evaluate the user experience of visitors to an outdoor ethnographic museum. The results showed that 55% of the test participants were satisfied and 45% very satisfied with the way personalized content was delivered.

The pandemic has accentuated the power that influencers have to influence their followers. Various scientific approaches highlight the lack of moral and ethical responsibility of these creators when disseminating content under highly sensitive tags such as health. This article presents a correlational statistical study of 443 Instagram accounts with more than one million followers belonging to health-related categories. This study aims to describe the content of these profiles and their authors and to determine whether they promote health as accounts that disseminate health-related content, identifying predictive factors of their content topics. In addition, it aims to portray their followers and establish correlations between the gender of the self-described health influencers, the characteristics of their audience and the messages that these prescribers share. Health promotion is not the predominant narrative among these influencers, who tend to promote beauty and normative bodies over health matters. A correlation is observed between posting health content, the gender of the influencers and the average age of their audiences. The study concludes with a discussion on the role of public media education and the improvement of ethical protocols on social networks to limit the impact of misleading and false content on sensitive topics, increasing the influence of real health prescribers.

The nutraceutical value of pomegranate in the treatment of many neoplastic, cardiovascular, viral, inflammatory, metabolic, microbial, intestinal, reproductive and skin diseases is well-documented and is linked to its richness in phenolic compounds. This study aims to evaluate nutraceutical and genetic diversity of novel pomegranate genotypes (G1-G5) in comparison to leading commercial pomegranate varieties i.e. ‘Wonderful’, ‘Primosole’, ‘Dente di Cavallo’ and ‘Valenciana’. Morphometric measurements were carried out on fruits, accompanied by chemical characterization and the development of four new polymorphic SSR markers involved in the flavonoid pathway. The cultivars displayed a marked variability in the weight and shape of fruits, as well as in the weight of arils and juice yield. The highest level of total phenolic content and antioxidant activity was found in ‘Wonderful’ and G4, while the lowest was in ‘Dente di Cavallo’. Furthermore, the results showed that the pomegranate juice, is an excellent source of minerals, especially potassium, which plays a key role in organ functioning. The new flavonoid-related markers effectively differentiated the cultivars with the same diversity pattern as morpho-chemical characterization, so the SSRs developed in the present study can be used as a rapid tool for the identification of pomegranate cultivars with relevant nutraceutical traits.

The article explores the task of making higher education more profession-oriented. In this context, we consider the technology of structuring and matching professional activities and content of professional education curricula with the help of ontology. This technology employs intelligent analysis of labor market and educational content matching with the aim to organize educational programs and verify professional competences based on their ontological properties. The article also considers development of a professional training cognitive map that can help design the student’s personalized educational trajectory factoring in the given parameters.

In many image processing and computer vision applications, the main aim is to describe image contents. So, different visual properties such as color, texture and shape are extracted to make aim. In this respect, texture information play important role in image description and visual pattern classification. Texture is referred to a specific local distribution of intensities that is repeated throughout the image. Since now different operations or descriptors have been proposed to analysis texture characteristics. In the multi object images specific texture operators usually doesn’t provide accurate results. So, in many cases, combination of texture operators are used to achieve more discriminant features. In this paper, some combination methods are survived to analysis effect of combinational texture features in image content description. Also, in the result part, different related methods are compared in terms of accuracy and computational complexity.

An increasing global aridification due to climate change has made the health monitoring of vegetation indispensable to maintaining the food supply chain. Cost-effective and smart irrigation systems are required not only to ensure the efficient distribution of water, but also to track the moisture of plant leaves, which is an important marker of the overall health of the plant. This paper presents a novel electromagnetic method to monitor the water content (WC) and characterization in plant leaves utilizing the absorption spectra of water molecules in the terahertz (THz) frequency for four consecutive days. We extracted the material properties of leaves of eight types of pot herbs from the scattering parameters, measured using a material characterization kit in the frequency range of 0.75 to 1.1 THz. From the computed permittivity, it is deduced that the leaf specimens increasingly become transparent to the THz waves as they dry out with the passage of days. Moreover, the loss in weight and thickness of leaves were observed due to the natural evaporation of leaf moisture cells and change occurred in the morphology of fresh and water-stressed leaves. It is also illustrated that loss observed in WC on day 1 was in the range of 5\% to 22\%, and increased from 83.12\% to 99.33\% on day 4. Furthermore, we observed an exponential decaying trend in the peaks of the real part of the permittivity from day 1 to 4, which was reminiscent of the trend observed in the weight of all leaves. Thus, results in paper demonstrated that timely detection of water stress in leaves can help to take proactive action in relation to plants health monitoring, and for precision agriculture applications, which is of high importance to improve the overall productivity.

Like the rest of the globe, Forests in Sub-Saharan Africa (SSA) continue to play a vital role when it comes to food security from the perspective of forest function of climate regulation, water provision, and soil protection. Nevertheless, most of the recent deforestation practices in various countries indicate that the region could face severe food insecurity in the near future since there are already signs of shortage in food production. This study, therefore, examines deforestation, climate change, and food security nexus in SSA while exploring a wide range of examples of food insecurity in the region. Content analysis and a synthetic literature study were conducted using data from scientific data banks. The study links deforestation, climate change to food security while citing examples from various SSA countries such as Cameroon, Nigeria, Kenya to mention but a few. More so, the study investigates how deforestation contributes to climate change, and how such change directly affects agricultural output and hence food security. Lastly, the study discusses the various implication of deforestation in relation to food security.

Objective: Lipids are secreted into milk as bilayer-coated structures: milk lipid globules (MLGs). Adipophilin (ADRP) and perilipin 3 (TIP47) are associated with MLGs in human breast milk; however, the role of these proteins in milk lipid secretion is not fully understood. The aim of the study was to investigate levels of ADRP, TIP47 and total lipid content in human breast milk, their mutual correlations and dynamics during lactation. Research Methods & Procedures: Milk samples from 22 healthy lactating women (Caucasian, Central European) were collected at five time points during lactation (1–3, 12–14, 29–30, 88–90 and 178–180 days postpartum). Mass spectrometry-based method was used for quantification of ADRP and TIP47 in the samples. The gravimetric method was used to determine milk total lipid content. Results: We observed distinctive trends in ADRP, TIP47 levels and lipid content in human breast milk during the first 6 months of lactation. We also found a significant association between lipid content and ADRP, lipid content and TIP47, and ADRP and TIP47 concentrations in breast milk at all sampling points. Moreover, we derived an equation for estimating the mean lipid content of milk based on ADRP concentration in human breast milk. Conclusions: A mass spectrometry-based method was developed for quantifying ADRP and TIP47 in human breast milk. Strong mutual correlations were found between ADRP, TIP47 and total lipid content in human breast milk.

Vitamin D has previously been quantified in some plants and algae, particularly in leaves of the Solanaceae family. We measured the vitamin D content of Australian native food plants and Australian-grown edible seaweed. Using liquid chromatography with triple quadrupole mass spectrometry, 13 samples (including leaf, fruit and seed) were analysed in duplicate for vitamin D₂, vitamin D₃, 25-hydroxyvitamin D₂ and 25-hydroxyvitamin D₃. Five samples contained vitamin D₂: raw wattleseed (Acacia victoriae) (0.03 µg/100 g dry weight (DW)); fresh and dried lemon myrtle (Backhousia citriodora) leaves (0.03 and 0.24 µg/100 g DW, respectively); dried leaves and berries of Tasmanian mountain pepper (Tasmannia lanceolata) (0.67 and 0.05 µg/100 g DW, respectively). Fresh kombu (Lessonia corrugata) contained vitamin D₃ (0.01 µg/100 g DW). Detected amounts were low; however, it is possible that exposure to ultraviolet radiation may increase the vitamin D content of plants and algae if vitamin D precursors are present.

One of the challenges in Content-Based Image Retrieval (CBIR) is to reduce the semantic gaps between low-level features and high-level semantic concepts. In CBIR, the images are represented in the feature space and the performance of CBIR depends on the type of selected feature representation. Late fusion also known as visual words integration is applied to enhance the performance of image retrieval. The recent advances in image retrieval diverted the focus of research towards the use of binary descriptors as they are reported computationally efficient. In this paper, we aim to investigate the late fusion of Fast Retina Keypoint (FREAK) and Scale Invariant Feature Transform (SIFT). The late fusion of binary and local descriptor is selected because among binary descriptors, FREAK has shown good results in classification-based problems while SIFT is robust to translation, scaling, rotation and small distortions. The late fusion of FREAK and SIFT integrates the performance of both feature descriptors for an effective image retrieval. Experimental results and comparisons show that the proposed late fusion enhances the performances of image retrieval.

Sorghum has become increasingly popular for diverse applications, including food, feed, and bioenergy. The present study aimed to perform a bibliometric and content analysis on sorghum research in the industrial-agricultural sector to evaluate global research patterns, emerging topics, and future trends. The bibliometric analysis of the Scopus bibliographic metadata was done using Bibliometrix and Vosviewer. The results of this investigation show the descriptive analysis underscored fluctuation in research output and citation impact over the years. The identified four patterns through co-occurrence analysis encompassed central themes of sorghum research, including genetic expression and plant stress cluster, cereal crop and yield cluster, biomass and microbial bioprocessing, and metabolism and antioxidant cluster. The thematic map portrays a comprehensive view of cereal crops and yields, biomass and microbial bioprocessing, metabolism and antioxidant research, environmental remediation and sustainable agriculture practices, and the declining theme of starch. The findings provide valuable insights into the global pattern of sorghum research and emerging trends, thus directing future multidisciplinary research efforts for enhanced knowledge and sustainable practices in the industrial-agricultural sector.

Most people living in Europe's cities are still exposed to levels of air pollution deemed harmful by the World Health Organization. In the modern world, air pollution is the foremost concern because of its impact in human health and economy. This strong connection appears gaining a lot of concern, driven by new installed low-cost electrochemical sensors monitoring systems. Highly accuracy, real-time monitoring, daily and yearly statistics, data access from experts or simple users, low-cost equipment and forecasting needs, enforce the market to develop new air quality monitoring systems using advanced technologies and protocols. In this study, a comparison via low-cost electrochemical sensors and of static, fixed site measurement monitoring station, is taking place in Athens, Greece, along with the data quality and Air Quality Index (AQI) including data accuracy and quality of data concerning adverse health effects due to air pollution. The findings presented in this work, relate to different flexible and affordable alternatives adopted during the evaluation and calibration of low-cost gas sensors for the monitoring. The significance of the positive results is particularly useful, especially considering the founding for interference, environmental conditions affections and air quality information including indexes and health recommendations for a specific location.

Ethylene Oxide (EtO) is a colorless, flammable gas at room temperature, produced by the catalytic oxidation of ethylene. EtO is widely used by medical sterilization facilities to clean medical supplies and equipment. Recent epidemiological studies showed that EtO is a more potent carcinogen than previously documented, leading the Environmental Protection Agency (EPA) to update, in December 2016, the inhalation unit risk estimate for EtO. This resulted in the identification of EtO as a potential health concern in several areas across the US, including the state of Utah. The geography surrounding Salt Lake Valley creates a bowl; ideal for collecting air pollution emissions. The region often experiences inversion episodes which inhibit vertical mixing and cause an accumulation of air pollutants, leading to unhealthy pollution levels. Using the EPA's dispersion modeling software, AERMOD, this study estimated EtO concentrations through facility stack and fugitive emissions modeling results. These values were compared with those of canister-based concentrations from ambient air samples taken near a medical device sterilization facility in the Salt Lake Valley. Stainless steel, whole-air passivated canisters were used to collect 24-hour ambient concentration samples of EtO. Eight locations surrounding a Salt Lake Valley medical device sterilization facility and four background sites were chosen to measure the ambient concentrations. Accounting for potential atmospheric impacts on EtO, measurements were sampled in winter 2022 (January-March) and summer 2022 (July-September). The modeled EtO concentrations were adjusted to account for background values associated with the winter or summer data. Then the two methodologies were compared using a Wilcoxon Sign-ranked, paired test. The statistical analysis resulted in six of the eight sample locations surrounding the sterilization facility being significantly different when comparing canister-based measurements of ambient EtO to modeled estimates. Canister-based measurements taken at sites one, three, and four were statistically greater than the modeled estimates, while sites two, five, and seven were statistically less than the modeled estimates. Also, the summer background value calculated was almost 2.5 times greater than the winter. The results do not suggest whether one method is more or less conservative than the other. In conclusion, the five of the closest sites and site seven were statistically different when comparing measured and modeled ambient concentrations of EtO. The comparison results do not clearly indicate if a correction factor could be derived for future human exposure to cancer risk assessment modeling. However, it is reasonable that the closer to the sterilization facility, the more total EtO exposure will be realized.

Air pollution has been a major environmental issue worldwide from the last few decades. It is a man-made issue that has a serious harmful impact on the environment and the health of humans. There are different sources of emission, but industrial processes and motor vehicles contribute to a chief part of air pollution. It has acute as well as chronic effects on the health of humans and affects different organs. It is thought the main environmental risk factor in the incidence and progression of several diseases such as lung cancer, asthma, Alzheimer's and Parkinson's diseases. Long-term exposure to air pollution has different toxicological impacts on humans such as respiratory and cardiovascular diseases, neuropsychiatric complications, eye irritation and skin diseases. As per the study by the World Health Organization (WHO), nitrogen oxides (NOx), carbon monoxide (CO), ozone (O₃), sulfur dioxide (SO₂), volatile organic compounds (VOCs) and heavy metals are the major air contaminants. These pollutants are different in their properties, composition and time of disintegration. The aim of this study is to review the different sources, types, impacts, challenges and mitigation of air pollution in detail.

Cigarette smoking and air pollution (particulate matter) are recognized as two major etiological factors for lung cancer. Of all the risk factors, cigarette smoking is significantly associated with lung carcinogenesis. The main mechanism lies in the metabolically activated carcinogens (majorly polycyclic aromatic hydrocarbons and nitrosamines), which could covalently bind with DNA molecules and lead to irreversible mutations in pivotal cancer genes, such as TP53 and KRAS. Another major etiological factor for lung cancer is air pollution, which is with complex compositions and ubiquitous in daily life, especially in developing countries as China and India. The latest literatures on lung cancer epidemiology and etiology have been briefly summarized and reviewed in this work.