In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

Ethylene Oxide (EtO) is a colorless, flammable gas at room temperature, produced by the catalytic oxidation of ethylene. EtO is widely used by medical sterilization facilities to clean medical supplies and equipment. Recent epidemiological studies showed that EtO is a more potent carcinogen than previously documented, leading the Environmental Protection Agency (EPA) to update, in December 2016, the inhalation unit risk estimate for EtO. This resulted in the identification of EtO as a potential health concern in several areas across the US, including the state of Utah. The geography surrounding Salt Lake Valley creates a bowl; ideal for collecting air pollution emissions. The region often experiences inversion episodes which inhibit vertical mixing and cause an accumulation of air pollutants, leading to unhealthy pollution levels. Using the EPA's dispersion modeling software, AERMOD, this study estimated EtO concentrations through facility stack and fugitive emissions modeling results. These values were compared with those of canister-based concentrations from ambient air samples taken near a medical device sterilization facility in the Salt Lake Valley. Stainless steel, whole-air passivated canisters were used to collect 24-hour ambient concentration samples of EtO. Eight locations surrounding a Salt Lake Valley medical device sterilization facility and four background sites were chosen to measure the ambient concentrations. Accounting for potential atmospheric impacts on EtO, measurements were sampled in winter 2022 (January-March) and summer 2022 (July-September). The modeled EtO concentrations were adjusted to account for background values associated with the winter or summer data. Then the two methodologies were compared using a Wilcoxon Sign-ranked, paired test. The statistical analysis resulted in six of the eight sample locations surrounding the sterilization facility being significantly different when comparing canister-based measurements of ambient EtO to modeled estimates. Canister-based measurements taken at sites one, three, and four were statistically greater than the modeled estimates, while sites two, five, and seven were statistically less than the modeled estimates. Also, the summer background value calculated was almost 2.5 times greater than the winter. The results do not suggest whether one method is more or less conservative than the other. In conclusion, the five of the closest sites and site seven were statistically different when comparing measured and modeled ambient concentrations of EtO. The comparison results do not clearly indicate if a correction factor could be derived for future human exposure to cancer risk assessment modeling. However, it is reasonable that the closer to the sterilization facility, the more total EtO exposure will be realized.

The ambient air quality data for particulate matter as well as criteria of gaseous pollutants were assembled during December 2013 to December 2015 from the Continuous Air Quality Monitoring Station (CAMS) located at Agrabad, Chittagong. The observation showed that during April- October, 24 hour average concentration of PM10 and PM2.5 were within the National Ambient Air Quality Standard (NAAQS) level but it increased occasionally by more than two and a half times during the whole non-monsoon period (November-March). The highest values found of PM2.5 were 321.1 µg/m³ in January, 2013 and 220.34 µg/m³ in December 2015. Whether, the highest alarming concentration of PM10 was reported as 474 µg/m3 in January 2007. The other gaseous pollutants such as SO₂, NO₂, O₃, CO and Hydrocarbons remain well within the permissible limit except dry non-monsoon period. The yearly average increase of Air Quality Index (AQI) value indicates the growth rate of air pollution in Chittagong city. The main responsible pollutant for air pollution is found PM_2.5.

The application of smartphone-based color evaluation of passive sampling devices for gases has only been sparsely reported. The present review aims to compile available publications with respect to the configuration of the passive samplers, conditions of smartphone photographing, analytical procedure for color detection and quantification (including calibration processes), and their application to different target gases. The performance of the methods - whenever available - is presented regarding the analytical specifications selectivity, sensitivity, and limit of detection in comparison with other color evaluation methods of passive samplers. Practical aspects like requirements of instrumentation and ease of use will be outlined in view of the potential employment in education and citizen science projects. In one section of the review the inconsistent terminology of passive and diffusive sampling is discussed in order to clarify the distinction of information obtained from the uptake of the passive samplers between gas-phase concentration and the accumulated deposition flux of gaseous analytes. Colorimetric gas sensors are included in the review when applied in passive sampling configurations and evaluation is performed with smartphone-based color evaluation. Differences in the analytical procedures employed after the passive sampling step and prior to the detection of the colored compounds are also presented.

Nowadays a recognized need for accurate observations of atmospheric aerosols (AEs) and reactive gases (RGs) exists in the framework of regional, national and global near-surface networks based on permanent or mobile measurement stations. In this context, a paramount and not-trivial issue is related to the correct execution of continuous sampling of ambient air and its subsequent distribution to measurement analyzers hosted inside the stations. Sampling artifacts must be minimized for obtaining reliable pictures of ambient air composition. To respond to this need, a suite of novel “smart” and relatively low-cost systems for the continuous sampling of ambient air was developed in the framework of the Project I-AMICA (2012 – 2015, www.i-amica.eu). These systems were designed to execute AE and RG measurements according with WMO/GAW and ACTRIS recommendations and standard operation procedures. A particular attention was dedicated to the stabilization and control of the sampling flow rates and temperatures. The analysis of one full year of operations at the WMO/GAW regional station of Capo Granitola (GAW ID: CGR, Italy), allowed to conclude that these systems are effective in meeting the technical requirements for correct execution of AE and RG measurements

In the paper, a study of the performance of unmanned ground vehicle (UGV), establishes numerical simulation model of the chassis system by three-dimensional software and finite element analysis software. Based on the numerical modelling and analysis, the work focuses on study of the strength and stiffness of the vehicle's chassis and researched the distribution of stress and deformation under the extremal condition. The paper also presents an autopilot design with new cascade control system for an autonomous motion of an unmanned ground vehicle based on Proportional-Integral-Derivative (PID) and Feed-Forward (FF) control. The PID-FF controller is a part of dedicated for presented UGV used in a hybrid control system for precise control and stabilization, necessary to increase the vehicle motion stability and maneuvers precision. The hybrid PID-FF control system proposed for the ground vehicle model gives a satisfactory quality of control, while maintaining the simplicity of the control system. Presented tests performed in area of mechanical design and control analysis gives good results and proves usefulness of designed unmanned device.

This study determined the temporal variation of PM2.5 in ambient air in Thohoyandou and further assessed the associated health risks. The levels of PM2.5 were quantified for a period of 1 year (April 2017-April 2018) using the gravimetric method. There was no significant difference (P-value = 0.18) in concentrations of both PM2.5 samples collected during weekdays (11.29 µg.m-3) and weekends (9.86 µg.m-3). However, higher concentrations of PM2.5 were measured in spring and the lowest was measured in summer. The cancer risk obtained for PM2.5 (2.21 × 10−5, 3 × 10-4, and 5 × 10-4 for infants, children, and adults respectively) in the outdoor air of Thohoyandou has exceeded the limit values by the USEPA and WHO, implying a significant risk for the whole population. For non-carcinogenic risks, the HQ values were 2.60, 4.81, and 2.60 for infants, children, and adults respectively. The HQ value >1 indicates a non-carcinogenic risk to the residents in Thohoyandou and a higher risk to children. Moreover, PM2.5 in Thohoyandou is responsible for 0.15% and 0.13% of deaths resulting from cardiovascular disease and lung cancer respectively for adults above 30 years. PM2.5 is causing adverse health effects in Thohoyandou as deduced from the health risk assessment. Therefore, it is recommended that further epidemiological studies be conducted in Thohoyandou to estimate the burden of disease due to exposure to particulate matter and suitable controlling policies be arranged to reduce particulate matter.

(1) Background: Environmental and public health research has given considerable attention to the impact of air quality on brain health, with systematic reviews widespread. No literature review has been done for cognitive frailty – a multidimensional syndrome combining physical frailty and cognitive impairment and their apparent co-dependence, linked to increased vulnerability and adverse health outcomes, including dementia. Instead, cognitive decline and frailty is implicitly explored through research on air quality and comorbid cognitive and physical decline in elderly populations. (2) Methods: A scoping review was conducted to explore the need for a systematic review. Combining Arksey and O’Malley [1] and PRISMA-ScR checklist [2], a scoping review of SCOPUS using ‘cogniti*’ + ‘resilience’ + ‘air quality’ or ‘cogniti*’ + ‘ageing’ + ‘air quality’ resulted in N=2503 articles, screened and reduced using inclusion and exclusion criteria, to N=16 articles. (3) Results: Air quality appears to be a critical risk factor for cognitive decline, even at air quality levels below WHO targets. Moderate long-term ambient air pollution appears linked to increased risk of cognitive frailty, suggesting earlier and more active interventions to protect older people. There are varied effects on cognition across the life course, with both emotional and functional impacts. Effects may be more detrimental to elderly people with existing conditions, including economic and health inequalities. Generalisation of results is limited due to the absence of a dose-response, variations in methods, controlling for comorbid effects, and variance across studies. (4) Conclusions: The findings support the need for more research and a more extensive summary of the literature.

Background: Lung cancer is one of the leading causes of morbidity and mortality worldwide with 25% of deaths due to lung cancer occurring in Europe. This study therefore sought to assess the burden of lung cancer by country and to evaluate the magnitude of fine Particulate Matter (PM2.5) and cigarette smoking by country in Europe. Methods: An ecological study nested on the World Health Organization air pollution database 2016 was conducted. We sampled 30 European Countries, with a total of 1625 mean annual samples of Particulate Matter (PM2.5) collected from 1625 designated sites (n = 1625). We further used the ‘World Health Disease Rankings’ database to extract Lung Cancer Morbidity and Mortality Rate by country. We used SAS version 9.4 to indicate the distribution of PM2.5 and Lung Cancer Mortality Rate. Results: Lung cancer Relative Risk (RR) was 1.0 in all never- smokers. RR for Ex-smokers for Adeno carcinoma was 3.5 in males and 1.1 in females, small cell carcinoma was 16.2 in males and 3.8 in females. RR for current smokers for Adeno carcinoma was 8.0 in males and 4.1 in females, small cell carcinoma was 57.9 in males and 18.2 in females. Mean annual PM2.5 by country ranged from 6.01 to 37.28µg/m3 whereas lung cancer mortality rate by country ranged from 19.67 to 54.26 deaths per 100,000 population. Conclusion: Cigarette smoking and exposure to both second hand smoke and high concentration of PM2.5 resulted into increased burden of lung cancer in Europe. Countries should re-strategize to reduce the burden of lung cancer in Europe.

Abstract: Metal-air batteries provide a most promising battery technology given their outstanding potential energy densities, which are desirable for both stationary and mobile applications in a ‘beyond lithium-ion’ battery market. Silicon- and iron-air batteries underwent less research and development compared to lithium- and zinc-air batteries. Nevertheless, in the recent past, the two also-ran battery systems made considerable progress and attracted rising research interest due to the excellent resource-efficiency of silicon and iron. Silicon and iron are among the top five of the most abundant elements in the earth’s crust, which ensures almost infinite material supply of the anode materials, even for large scale applications. Furthermore, primary silicon-air batteries are set to provide one of the highest energy densities among all batteries, while iron-air batteries are frequently considered as a highly rechargeable system with decent performance characteristics. Considering fundamental aspects for the anode materials, i.e., the metal electrodes, in this review, we will first outline the challenges, which explicitly apply to silicon- and iron-air batteries and prevented them from a broad implementation so far. Afterwards, we provide an extensive literature survey regarding state-of-the-art experimental approaches, which are set to resolve the aforementioned challenges and might enable the introduction of silicon- and iron-air batteries into the battery market in the future.

We introduce the Symplectic Structure of Information Geometry based on Souriau’s Lie Group Thermodynamics model, with a covariant definition of Gibbs equilibrium via invariances through co-adjoint action of a group on its moment space, defining physical observables like energy, heat, and moment as pure geometrical objects. Using Geometric (Planck) Temperature of Souriau model and Symplectic cocycle notion, the Fisher metric is identified as a Souriau Geometric Heat Capacity. Souriau model is based on affine representation of Lie Group and Lie algebra that we compare with Koszul works on G/K homogeneous space and bijective correspondence between the set of G-invariant flat connections on G/K and the set of affine representations of the Lie algebra of G. In the framework of Lie Group Thermodynamics, an Euler-Poincaré equation is elaborated with respect to thermodynamic variables, and a new variational principal for thermodynamics is built through an invariant Poincaré-Cartan-Souriau integral. The Souriau-Fisher metric is linked to KKS (Kostant-Kirillov-Souriau) 2-form that associates a canonical homogeneous symplectic manifold to the co-adjoint orbits. We apply this model in the framework of Information Geometry for the action of an affine Group for exponentiel families, and provide some illustrations of use cases for multivariate Gaussian densities. Information Geometry is presented in the context of seminal work of Fréchet and his Clairaut-Legendre equation. Souriau model of Statistical Physics is validated as compatible with Balian gauge model of thermodynamics. We recall the precursor work of Casalis on affine group invariance for natural exponential families.

Introduction: Ambient air pollution is major global health problem and commercial drivers are particularly exposed to it. No systematic assessment of the health risks associated with occupational exposure to ambient air pollution in this population has been carried out. Methods: We conducted a systematic review using a protocol-driven strategy. Papers published from inception to 20th April 2018 in MEDLINE, EMBASE, CINAHL, African journals online, Cochrane library, ISRCTN and WHO ICTRP databases were screened for inclusion by two independent reviewers. Original articles with at least an available abstract in English or French were included. Results: The initial search retrieved 1454 published articles of which 20 articles were included. 3 Studies reported a significant difference in white blood cells (106/L) among commercial motorcyclists compared to rural inhabitants (5.041±1.209 vs 5.900±1.213,p=0.001), an increased risk of lung cancer (RR=1.6, 95%CI 1.5-1.8) in bus drivers and an increased standardized mortality ratio (SMR) in bus drivers from Hodgkin’s lymphoma (SMR 2.17, 95%CI 1.19-3.87) compared to white collar workers. Other studies also found that drivers had more oxidative DNA damage and chromosome breaks. 4 papers failed to demonstrate that the drivers were more exposed to air pollution than the controls. 3 other studies also reported no significant difference in lung function parameters and respiratory symptoms. The genetic polymorphisms of detoxifying enzymes were not also homogeneously distributed compared to the controls. Conclusion: There is some evidence that occupational exposure to ambient air pollution among commercial drivers is associated with adverse health outcomes but the existing literature is limited with few studies of small sample size, methodological weaknesses and contradictory findings. Further research is recommended.

Urban cities in sub-Saharan Africa (SSA) are faced with ambient air pollution. This is an important public health problem with models and limited monitoring data indicating high concentrations of pollutants such as fine particulate matter (PM_2.5). Going through most global air quality index maps, however, information about ambient pollution from SSA is scarce. We evaluated the feasibility and practicality of longitudinal measurements of ambient PM_2.5 using low-cost air quality sensors (Purple Air-II-SD) across thirteen locations in seven countries in SSA. Devices were used to gather data over a 30-day period with the aim of assessing the efficiency of its data recovery rate and identifying challenges experienced by users in each location. The median data recovery rate was 94% (range: 72% to 100%). The mean 24-hour concentration measured across all sites was 38 µg/m³ with the highest PM_2.5 period average concentration of 91 µg/m³ measured in Kampala, Uganda and lowest concentrations of 15 µg/m³ measured in Faraja, The Gambia. Kampala-Uganda and Nnewi-Nigeria recorded the longest periods with concentrations>250µg/m³. Power outages, SD memory card issues, internet connectivity problems and device safety concerns were important challenges experienced when using Purple Air-II-SD sensors. Despite some operational challenges, this study demonstrated that it is reasonably practicable and feasible to establish a network of low-cost devices to provide data on local PM_2.5 concentrations in SSA countries. Such data are crucially needed to raise public-, societal and policymaker awareness about air pollution across SSA.

Air pollution is a leading cause of death in the United States, and is associated with adverse health outcomes, including increased vulnerability to coronavirus disease 2019 (COVID-19). The AirBeam2 was used to measure particulate matter with a diameter of 2.5 micrometers or smaller (PM2.5), to investigate differences between indoor and ambient levels at seven private homes in New York during and after the COVID-19 lockdown. Measurements taken in 2020 winter, spring and fall and in fall 2022 showed that 90% of the time, indoor PM2.5 levels exceeded outdoor levels both during and after the COVID-19 lockdown, p = 0.03, and exceeded safety levels. Higher indoor PM2.5 levels attributed to little or no ventilation from cooking and smoke in the kitchen and basements, were significantly greater in fall than in winter. Higher ambient PM2.5 levels were attributed to vehicular traffic at a street-facing sampling site. PM2.5 sources identified in this study may help in devising control strategies to improve indoor air quality (IAQ), and consequently alleviate respiratory health effects. These findings may be used as a basis for in-house modifications including natural ventilation and use of air purifiers to reduce exposures, mitigate future risks, and prevent potential harm to vulnerable residents.

The author demonstrates a stable Lagrangian solid modeling method, tracking the interactions of solid mass particles rather than using a meshed grid. This numerical method avoids the problem of tensile instability often seen with smooth particle applied mechanics by having the solid particles apply stresses expected with Hooke's law, as opposed to using a smoothing function for neighboring solid particles. This method has been tested successfully with a bar in tension, compression, and shear, as well as a disk compressed into a flat plate, and the numerical model consistently matched the analytical Hooke's law as well as Hertz contact theory for all examples. The solid modeling numerical method was then built into a 2-D model of a pressure vessel, which was tested with liquid water particles under pressure and simulated with smoothed particle hydrodynamics. This simulation was stable, and demonstrated the feasibility of Lagrangian specification modeling for fluid–solid interactions.

The concentration of total suspended particles (TSP) and nanoparticles (PM0.1) over Hat Yai city, Songkhla province, southern Thailand was measured in 2019. Organic carbon (OC) and elemental carbon (EC) were evaluated by carbon aerosol analyzer (IMPROVE-TOR) method. Thirteen trace elements including Al, Ba, K, Cu, Cr, Fe, Mg, Mn, Na, Ni, Ti, Pb, and Zn were evaluated by ICP-OES. Annual average TSP and PM0.1 mass concentrations were determined to be 58.3 ± 7.8 and 10.4 ± 1.2 µg/m3, respectively. The highest levels of PM occurred in the wet season with the corresponding values for the dry seasons being lower. The annual average OC/EC ratio ranged from 3.8 - 4.2 (TSP) and 2.5 - 2.7 (PM0.1). The char to soot ratios were constantly less than 1.0 for both TSP and PM0.1, indicating that land transportation is the main emission source. A principal component analysis (PCA) revealed that road transportation, industry, and biomass burning are the key sources of these particles. However, PM arising from Indonesian peatland fires causes an increase in the carbon and trace element concentrations in southern Thailand. The findings make useful information for air quality management and strategies for controlling this problem, based on a source apportionment analysis.

Particulate matter (PM) is one of the problems faced in environmental science. It has health effects on man and animals in both developed and developing countries. Research and efforts have been on it several years back. Policy statements and efforts have been published. This review paper is an added information on air pollution. In it, efforts were made in discussing these: classification, effects, methodology, case studies and source apportionment. It is hoped that this paper would contribute to existing knowledge on PM.

As of now, anthropogenic habitat injury via dissemination of manufactured chemicals is injuring the world’s ecosystems, but doctors have yet to recognize its consequences to humans. Recognition of overt toxicity due to chronic low-dose exposure will open the door to diagnosis, sequential elimination studies, and prescriptions for preventive cure that represent a first step in preventing escalating chronic diseases. This paper offers a diagnostic construct for such use: chronic ambient poisoning. Incorporating it into clinical practice can reduce misdiagnosis of gastro- and near-toxicity that doctors and patients presently suppress rather than remove, and reduce patient co-dependence with proton-pump inhibitors, anxiolytics, and antidepressants—and the thriving “alternative” health industry. This diagnostic elephant-in-the-room is presently missed for reasons of habit (when an ailment is not recognized, it cannot be included in the differential diagnosis) and of poor conduct and interpretation of non-clinical research studies that are taken to mean an absence of evidence is evidence of absence. Moreover, modern methods fail when: the exposure comprises a “daily cocktail” of poisons acting additively, interactively, and cumulatively over a lifetime; when there is no normal, unexposed comparison group; and when absence of a robust etiopathogenetic model disallows inapt statistics. Only patient-led, consultant-informed sequential elimination studies can “peel the onion” of toxicity and its recognition and “preventive cure”. Clinical use of the chronic ambient poisoning diagnosis can thus open the door to stemming and reversing anthropogenic epidemics.

The purpose of this study is to assess the concentration-response relations between conjunctivitis and exposure to ambient ozone. This retrospective study includes emergency department (ED) visits for conjunctivitis in Edmonton, Canada, for the period April 1992–March 2002. Daily average levels of ozone (range: 1.2–50.9, ppb), of temperature, and of relative humidity were estimated and used for the period of the study. For each of the considered exposure lags, (from 0 to 9 days), six different models were fitted to estimate the concentration-response function. The goodness of fit was assessed using the Akaike information criterion. During the period of the study, 17,211 ED visits for conjunctivitis were recorded and used. For all subjects together, a positive statistically significant association was obtained for the exposure lagged by 5 days. For female subjects, lags 1, 3, and 9 had positive statistically significant associations (lag 2 had negative associations). For male subjects, only lag 5 had a positive statistically significant association. The estimated non-linear concentration-response functions for the considered groups (all, males, females) and lags, revealed the associations along the exposure levels. The fitted shapes are described by algebraic functions and may have various forms. The estimated functions are useful to determine the risk associated with exposure to ground-level ozone.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

An important aspect of the new sustainable development goals (SDGs) is a greater emphasis on reducing the health impacts of urban ambient air pollution (AAP) in developing countries. Meanwhile, the burden of disease attributable to AAP in sub-Saharan Africa (SSA) is growing, yet estimates of its impact in the region are likely underestimated due to a lack of air quality monitoring, the paucity of epidemiological studies, and important population vulnerabilities in the region. The lack of studies in the SSA region also represents an important global health disparity and environmental justice issue because thousands of air pollution health effects studies have been conducted in Europe and North America rather than in some of the most polluted regions of the world, such as SSA. In this review, we synthesize all of the ambient air pollution epidemiological studies that have been conducted in SSA to date. We highlight the gaps in AAP epidemiological studies conducted in different sub-regions of SSA and provide methodological recommendations for future environmental epidemiology studies addressing AAP in the SSA region.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

Acute and chronic respiratory diseases impose a significant economic and health burden. Distal small airway assessment requires invasive procedures such as a bronchoscopy and bronchoalveolar lavage. The Particles in Exhaled Air (PExA) device provides a non-invasive means of assessing small airways; it captures distal airway particles sized around 0.5-7m and contains particles of respiratory tract lining fluid (RTLF) that originate during airway closure and opening. The PExA device can measure particle count and mass according to particle size. Subsequent capture of particles in a thin membrane enables application of various analytical methods to assess a broad range of biomolecules including phospholipids, proteins, inflammatory profile, and other metabolites to characterise inflammation and diseases processes such as asthma, chronic obstructive pulmonary disease, acute respiratory distress syndrome, lung cancer, and more recently acute infections such as COVID-19. PExA analysis provides a promising alternative to traditional investigative methods in the assessment, diagnosis, and management of respiratory conditions. By evaluating specific biomarkers in the RTLF associated with airway inflammation, PExA may offer a more accurate and comprehensive understanding of the molecular-level changes in the small airways of patients with acute and chronic lung diseases.

It is concerning that Cameroon's urban centers are experiencing an alarming rise in air pollution as a result of urbanization, population growth, industrial activity, and transportation emissions. We examined the causes, health impacts, research methodology, case studies, and government measures to address the urgent issue of air pollution in Cameroon's urban regions. We have emphasized how Cameroon's air pollution levels have significantly increased as a result of causes like population expansion, urbanization, industrial emissions, and automobile exhaust A thorough discussion of the negative health impacts of extended exposure to air pollution is included, with special attention to the sensitivity of the old and young. These effects include respiratory disorders, cardiovascular ailments, and early mortality. We emphasized the pressing need for all-encompassing strategies to address air pollution, such as increased public awareness campaigns, stronger emissions regulations, the development of renewable energy sources, and better waste management. The techniques employed in studies on air pollution, like as epidemiological research and air quality monitoring, are also explained to provide light on the unique health dangers that Cameroonian urban dwellers must contend with. We emphasized in our conclusion the significance of joint efforts by legislators, medical professionals, and the general people to reduce air pollution and protect public health in Cameroon in order to create a cleaner and healthier future. In order to protect public health in the future, it is imperative that Cameroon's air pollution be addressed.

Ecuador is an important center of biodiversity of the plant family Amaryllidaceae, specially the subfamily Amaryllidoideae, known as a source of important bioactive molecules. The aim of this study was to assess the chemical and biological potential of four different species of Amaryllidoideae collected in Ecuador: Urceolina formosa, Urceolina ruthiana, Clinanthus incarnatus, and Stenomesson aurantiacum. Sixteen alkaloids were identified in the bulb extract of these species by GC-MS, which the extract of S. aurantiacum exhibiting the greatest structural diversity. The potential of these three genera against Alzheimer’s disease was evaluated by measuring their AChE and BuChE inhibitory activity, revealing that C. incarnatus and U. formosa (from Sucumbíos province) showed the best results with IC50 values of 1.73 ± 0.25 and 30.56 ± 1.56 g·ml-1, respectively. Molecular dynamic assays were conducted to elucidate the possible interactions that occurs among 2-hydroxyanhydrolycorine and AChE enzyme, suggesting some similarity with those observed for galanthamine. This study enhances our understanding of the biodiversity of Amaryllidoideae species from Ecuador, highlighting their potential as a source of chemical compounds with pharmaceutical potential.

The article delves into the intricate phase transitions of 1-Octadecanol and n-Nonadecane within a binary system, unveiling dynamic structural changes under varying conditions. Through Fouri-er-transform infrared (FTIR) analysis, specific molecular vibrations were identified, shedding light on the molecular composition and interactions. The study highlights the challenges in detecting subtle phase transitions and emphasizes the individuality of molecular behaviours in closely related compounds. The findings underscore the complexity of phase transitions in binary systems and advocate for a nuanced approach to studying molecular structures and behaviours. Addi-tionally, the research contributes valuable insights into the molecular dynamics of Organic Polymer Functional Adsorption Materials, offering implications for synthetic waxy layers in plant epidermis.

Retiring coal power plants can reduce air pollution and health damages. However, the spatial distribution of those impacts remains unclear due to complex power system adjustments and pollution chemistry and transport. Focusing on coal retirements in Pennsylvania (PA), we analyze six counterfactual scenarios for 2019 that differ in retirement targets (e.g., reducing 50% of coal-based installed capacity vs. generation) and priorities (e.g., closing plants with higher cost, closer to Environmental Justice Areas, or with higher CO₂ emissions). Using a power system model of the PJM Interconnection, we find that coal retirements in PA shift power generation across PA and the Rest of PJM region leading to scenario-varying changes in the plant-level release of several air pollutants. Due to air pollution chemistry and transport and socio-demographics, these changes in turn give rise to a reduction of 10 to 182 PM_2.5-attributable deaths in PJM across the six scenarios, with most reductions occurring in PA. Scenarios that reduce more coal power generation yield greater aggregate health benefits due to air quality improvements in PA and adjacent downwind regions. In addition, vulnerable populations—in both PA and Rest of PJM—benefit most in scenarios that prioritize plant closures in PA near Environmental Justice Areas. These results demonstrate the importance of considering cross-regional linkages and socio-demographics in designing equitable retirement strategies.

Nanoparticles (NP), Nanoaerosols (NA), ultrafine particles (UFP), and PM0.1 (particles with a diameter ≤ 0.1 µm or 100 nm) are interchangeably used in the field of atmospheric studies. PM0.1 are emitted from both natural and anthropogenic sources. The main emission sources of PM0.1 are combustion processes, including biomass and fossil fuel. Moreover, secondary formation via atmospheric photochemical reactions can also occur depending on meteorological conditions and the suspended pollutant species. Identifying the physical and chemical characteristics and spatial and temporal variations is vital in terms of understanding the effect of NPs on the environment, the global climate, and human health risks. This review article summarizes recent research on PM0.1 in Thailand. The review involves peer-reviewed papers from Scopus and the Web of Science databases, and includes the most recently published articles in the past ten years (2013-2022). UFPs mainly come from the combustion processes such as motor vehicles. The high mass concentration of PM0.1 that occurs during the dry season in which open fires depend on the specific region of Thailand. Particulate pollution from local and cross-border countries also needs to be considered in terms of the concentrations of ambient nanoparticles. The overall conclusions reached will likely have a beneficial long-term impact on achieving a blue sky over Thailand through the development of coherent policies and managing new air pollution challenges and sharing knowledge with a broader audience.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

Background: Asthma is a widespread chronic respiratory disease that poses a significant public health challenge. The current study investigated the associations between air pollution and asthma severity among individuals residing near the Sohar industrial port (SIP) in Oman. Despite the presence of multiple major industrial complexes in Oman, limited knowledge regarding their impact on respiratory health is accredited. Hence, the primary objective of this study is to offer valuable insights into the respiratory health consequences of industrial air pollution in Al Batinah North. Methods: The state health clinics' records for patient visits related to asthma were collected for the timeframe spanning 2014 to 2022. Exposure was defined as the distance from SIP, Majan Industerial Area (MIA) and Sohar Industerial Zone (SIZ) to determine high, intermediate, and low exposure zones (12 km, respectively). Exposure effect modifications by age, gender, and smoking status were also examined. Results: The conducted cross-sectional study of 410 patients (46.1% males and 53.9% females) living in over 17 areas around SIP revealed that 73.2% of asthmatics were under 50 years old, with severity significantly associated with closeness to the port. Risk ratios were estimated to be (RR:2.42; CI95%: 1.01–5.78), (RR:1.91; CI95%: 1.01–3.6), and (RR:1.68; CI95%: 0.92–3.09) for SIP, MIP and SIZ areas, respectively, compared to the control area. Falaj Al Qabail (6.4 km) and Majees (6 km) had the highest number of asthma patients (N. 69 and N. 72), and highest percentages of severe asthma cases among these patients (28% and 24%) with significant risk ratios (RR:2.97; CI95%: 1.19–7.45 and RR:2.55; CI95%: 1.00–6.48), correspondingly. Moreover, severe asthma prevalence peaked in the 25-50 age group (RR:2.05; CI95%: 1.26–3.33), and this linkage between asthma and age was much more pronounced in males than females. Smoking and exposure to certain contaminant (dust and smoke) increased also the risk of severe asthma symptoms, but their effects were less important in the high risk zone, suggesting much more important risk factor. A neural network model accurately predicted asthma risk (94.8% accuracy), with proximity to Sohar Industrial Port as the most influential predictor. Conclusion: The study highlights the High asthma burden near Sohar Industrial Port, linked to port proximity and smoking and wind direction as major risk factors. These findings inform vital public health policies to reduce air pollution and improve respiratory health in the region, prompting national policy review.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

The non-contact patient monitoring paradigm moves patient care into their homes and enables long-term patient studies. The challenge, however, is to make the system non-intrusive, privacy-preserving, and low-cost. To this end, we describe an open-source edge computing and ambient data capture system, developed using low-cost and readily available hardware. We describe five applications of our ambient data capture system. Namely: (a) Estimating occupancy and human activity phenotyping; (b) Medical equipment alarm classification; (c) Geolocation of humans in a built environment; (d) Ambient light logging; and (e) Ambient temperature and humidity logging. We obtained an accuracy of 94% for estimating occupancy from video. We stress-tested the alarm note classification in the absence and presence of speech and obtained micro averaged F1 scores of 0.98 and 0.93, respectively. The geolocation tracking provided a room-level accuracy of 98.7%. The root mean square error in the temperature sensor validation task was 0.3°C and for the humidity sensor, it was 1% Relative Humidity. The low-cost edge computing system presented here demonstrated the ability to capture and analyze a wide range of activities in a privacy-preserving manner in clinical and home environments and is able to provide key insights into the healthcare practices and patient behaviors.

Abstract: Mass spectrometry research laboratories reported multiple probes for ambient ionization in the last years. Combining them with a mechanical moving stage enables automated sampling and imaging applications. We developed a robotic platform, which is based on RepRap 3D-printer components, and therefore easy to reproduce and to adopt for custom prototypes. The minimal step width of the Open LabBot is 12.5 μm, and the sampling dimensions (x, y, z) are 18 × 15 × 20 cm. Adjustable rails in an aluminium frame construction facilitate the mounting of additional parts such as sensors, probes, or optical components. The Open LabBot uses industry-standard G-code for its control. The simple syntax facilitates the programming of the movement. We developed two programs: 1) LABI-Imaging, for direct control via a USB connection and the synchronization with MS data acquisition. 2) RmsiGUI, which integrates all steps of mass spectrometry imaging: The creation of G-code for robot control, the assembly of imzML files from raw data and the analysis of imzML files. We proved the functionality of the system by the automated sampling and classification of essential oils with a PlasmaChip probe. Further, we performed an ambient ionization mass spectrometry imaging (AIMSI) experiment of a lime slice with laser desorption low-temperature plasma (LD-LTP) ionization, demonstrating the integration of the complete workflow in RmsiGUI. The design of the Open LabBot and the software are released under open licenses to promote their use and adoption in the instrument developers’ community.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

The use of artificial intelligence technologies may help companies obtain the optimal use of resources and accomplish more activities with an increase in productivity by 40%. With access to real-time data and the ability to learn from patterns and behaviors, AI can perform these routine tasks more efficiently. Ambient intelligence, Ami, is one of the applications of artificial intelligence, which is called artificial environmental intelligence, which is a concept that focuses on using technology to create an environment that is intelligent and responsive to the needs of its users. This technology has the potential to revolutionize disaster response and management, which in turn facilitates access to necessary information and resources. necessary vitality in the event of a crisis. It may use ambient intelligence to create a network of sensors that can detect and respond to changes in the environment. So that this network can be used to monitor the environment for potential disasters, such as floods, fires and earthquakes. Sensors can also be used to detect changes in temperature, humidity, and other environmental factors that may indicate a potential disaster. This information can then be used to alert emergency responders and provide them with the information needed to respond quickly and effectively. Ambient intelligence can also be used to create a comprehensive database of resources and information that can be accessed in times of crisis. This database may include information about the location of shelters, medical facilities, and other resources that can be used to assist those affected by a disaster. It may also provide information about the condition of roads, bridges, and other infrastructure that may be affected by a disaster. This information can be used to inform response and management decisions, helping to ensure that resources are used in the most efficient way possible. Ambient intelligence can be used to create a communication platform between emergency responders and those affected by a disaster. This platform can also be used to provide updates on the emergency situation, in addition to providing information about available resources to those affected. This can help ensure that those affected by a disaster can access the resources they need in a timely manner.

We examined whether the ambient illuminance during extended wakefulness modulates the homeostatic increase in human deep sleep [i.e. slow wave sleep (SWS) and electroencephalographic (EEG) slow-wave activity (SWA)] in healthy young and older volunteers. Thirty-eight young and older participants underwent 40 hours of extended wakefulness [i.e. sleep deprivation (SD)] once under dim light (DL: 8 lux, 2800K), and once under either white light (WL: 250 lux, 2800K) or blue-enriched white light (BL: 250 lux, 9000K) exposure. Subjective sleepiness was assessed hourly and polysomnography was quantified during the baseline night prior to the 40-h SD and during the subsequent recovery night. Both the young and older participants responded with a higher homeostatic sleep response to 40-h SD after WL and BL than after DL. This was indexed by a significantly faster intra-night accumulation of SWS and a significantly higher response in relative EEG SWA during the recovery night after WL and BL than after DL for both age groups. No significant differences were observed between the WL and BL condition for these two particular SWS and SWA measures. Subjective sleepiness ratings during the 40-h SD were significantly reduced under both WL and BL compared to DL, but were not significantly associated with markers of sleep homeostasis in both age groups. Our data indicate that not only the duration of prior wakefulness, but also the experienced illuminance during wakefulness affects homeostatic sleep regulation in humans. Thus, working extended hours under low illuminance may negatively impact subsequent sleep intensity in humans.

As the rapid development of communication industry, especially the 5G communication and IOT, there will be plenty of electromagnetic (EM) waves in the free space, which carry lots of energies. However, some of these energies are wasted in free space. To reuse these wasted energies, significantly growing interests are towards to the energy harvesting antennas. This paper is aimed to investigate a wearable antenna which can transfer RF energy from ambient sources to direct current by a soft and portable textile antenna. Among the numerous signals in mobile network, the GSM 1800, 3G, WiFi and 4G/5G will be chosen due to the city signal intensity distribution. Hence, a corresponding triple bands antenna has been designed to cover those frequency bands. The CST STUDIO SUITE is used in whole process of antenna design and simulation. The proposed antenna is a hooked dipole antenna with tuning bar (HATB) whose ends have small folded part in each side for better bandwidth performance. The presented antenna provides a wide operating band from 1.8 GHz to 2.5 GHz below -10 dB in return loss. And methods to overcome interference between antennas is found. Furthermore, using the corresponding rectifier to achieve the RF/DC conversion. The overall efficiency of whole rectifier is about 56.8 %, and output power level of the antenna system is 45.92nW. The experimental results could indicate that my textile hooked antenna harvester is a good choice for the charging system of personal wearable attachment, which could achieve low power absorbing for long distance anytime and anywhere.

The use of unmanned aerial aircrafts (UAVs) is governed by strict regulatory frameworks that prioritize safety. To guarantee safety, it is necessary to acquire and maintain situational awareness (SA) throughout the operation. Existing Canadian regulations require pilots to operate their aircrafts in visual line-of-sight. Therefore, the task of acquiring and maintaining SA primary falls to the pilots. However, the development of aerial transport is entering a new era with the adoption of a highly dynamic and complex system known as advanced air mobility (AAM), which involves UAV operating autonomously beyond visual line-of-sight. SA must therefore be acquired and maintained primarily by each UAV through specific technologies and procedures. In this paper, we review these technologies and procedures in order to decompose the SA of the UAV in the AAM. We then use the system modeling language to provide a high-level structural and behavioral representation of the AAM as a system having UAV as its main entity. In a case study, we analyze one of the flagships UAVs of our industrial partner. Results show that this UAV doesn’t have all the technologies and methodologies necessary to achieve all the identified SA goals identified for the safety of the AAM. This work is a theoretical framework intended to contribute to the realization of the AAM, and we also expect to impact the future design and utilization of UAVs.

The Upper Hunter Valley is a major coal mining area in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. The early part of this study identified two air quality subregions in the valley. This paper aims to provide a holistic summarisation of the relationships between elevated PM10 pollution in two subregions and the local- and synoptic-scale meteorological conditions for spring and summer, when PM10 pollution is relatively high. A catalogue of twelve synoptic types and a set of six local meteorological patterns have been quantitatively derived and linked to each other using the self-organising map (SOM) technique. The complex meteorology-air pollution relationships have been visualised/interpretated on the SOM planes for two representative locations. It was found that the influence of local meteorological patterns differed significantly for mean PM10 levels vs the occurrence of elevated pollution events and between air quality subregions. In contrast, synoptic types showed generally similar relationships with mean vs elevated PM10 pollution in the valley. Two local meteorological patterns, the hot-dry-northwesterly wind conditions and the hot-dry-calm conditions, were found most PM10 pollution conducive in the valley when combined with a set of synoptic counterparts. These synoptic types are featured with the influence of eastward migrating continental high pressure system and westerly troughs, or a ridge extending northwest towards coastal northern NSW or southern Queensland from the Tasman Sea. The method and results can be used in air quality research for other locations of NSW, or similar regions elsewhere.

This study investigates the mean annual water temperature trends at the confluence of the Sava and Danube Rivers, along with air temperature trends at the Belgrade meteorological station, spanning from 1956 to 2020. Results reveal a consistent increase in temperature across all three measuring stations, with the Danube experiencing a rise of 0.34°C/10 years, the Sava at 0.44°C/10 years, and Belgrade's air temperature increasing by 0.39°C/10 years. Employing the RAPS method, sharp rises in water temperature were pinpointed in 1989 for the Sava and 1990 for the Danube, while Belgrade's air temperature surge began in 1998. The highest intensity of air temperature increase within the recent period (1998-2020) was observed at the Belgrade observatory, reaching 0.76°C/10 years. Notably, the Sava exhibited a faster increase in water temperature over the last thirty years compared to the Danube. August marked the peak average water temperature for both rivers, while July recorded the highest average air temperature in Belgrade. Despite differing flow rates, both rivers exhibit similar hydrological regimes, with maximum flows occurring in April and minimum flows in August for the Sava, and October for the Danube. Seasonal temperature increases were most pronounced in summer, notably in August, with the smallest rises occurring during cold periods. Additionally, an inverse proportional relationship between mean annual water temperatures and discharges was observed at both river stations.

Agaricus bisporus is one of the most popular mushroom species in the world; however, mushrooms are highly susceptible to browning due to the absence of a protective cuticle layer and high respiration rate. The molecular mechanism underlying the process of mushroom browningneeds to be explored. Here, we analyzed the transcriptomic and metabolomic data from A. bisporusat ambient temperature. Specifically, a total of 263 significantly changed metabolites and 4492 differentially expressed genes were identified. Lipid metabolites associated with cell membrane degradation were predominantly up-regulated during ambient storage. Transcriptomic data further revealed the alterations of the expression of membrane lipid metabolism-related enzymes. Additionally, energy metabolic processes and products such as glycolysis and linoleic acid changed significantly during ambient storage, indicating their potential roles in the quality deterioration of A. bisporus. These findings provide new insights into the underlyingl ipidmetabolic mechanism of A. bisporus during postharvest ambient storage and will provide values for mushroom preservation techniques.

This study investigates the effects of ambient illumination and negatively polarized text color on visual fatigue, exploring the issue of visual fatigue when using visual display terminals in low-illumination environments. The research methodology utilized an experimental design to collect data on changes in pupil accommodation and blink rate through an eye tracker. Partici-pants completed a reading task while exposed to various text colors and ambient light conditions to evaluate visual fatigue and cognitive performance. The study's findings suggest that text color significantly affects visual fatigue, with red text causing the highest level of visual fatigue and yellow text causing the lowest level of visual fatigue. Improvements in ambient lighting reduce visual fatigue, but the degree of improvement varies depending on the text color. Additionally, cognitive performance is better when using yellow and white text but worse when using red text. Yellow text is the most effective choice for reducing visual fatigue under negative polarity. In-creasing ambient lighting can also improve visual fatigue in low-illumination conditions. These findings will offer valuable guidance for designing visual terminal device interfaces, especially for low-illumination or night environments, to minimize visual fatigue and improve the user ex-perience.

Elaborate sound design, including background music, ambient sounds (sounds describing the game world), and character sounds (sounds generated by the character’s actions), plays a pivotal role in modern videogames. However, the influence of these different types of sound on the player experience has not been extensively researched. This study examines the influence of these sound types on immersion, avatar identification, fun and perceived competence. In two experiments, participants played League of Legends in four different sound conditions. The first experiment revealed a non-significant trend in the effect of character sound on avatar identification. Ambient sounds, however, were limited in this experiment because the task restricted participants’ movement across the game map. Consequently, we adapted the task to allow for a wider variety of ambient sounds in the second experiment. Here, a significant impact of character sounds on immersion, avatar identification, and fun, was observed, as well as an interaction effect of character sounds and ambient sounds on fun. Furthermore, we observed a trend, though not statistically significant, suggesting that ambient sounds may influence the player’s sense of flow. These findings underline the distinct effects of different sound types and we discuss implications for the design of sound in video games.

Findings from studies of prenatal exposure to pesticides and adverse birth outcomes have been equivocal so far. We examined prenatal exposure to agricultural pesticides in relation to preterm birth and term low birthweight, respectively, in children born between 1998 and 2010 randomly selected from California birth records. We estimated residential exposures to agriculturally applied pesticides within 2 km of residential addresses at birth by pregnancy trimester for 17 individual pesticides and 3 chemical classes (organophosphates, pyrethroids, and carbamates). Among maternal addresses located within 2 km of any agricultural pesticide application, we identified 24,693 preterm and 220,297 term births, and 4,412 term low birthweight and 194,732 term normal birthweight infants. First or second trimester exposures to individual pesticides (e.g., glyphosates, paraquat, imidacloprid) or exposures to 2+ pesticides in the three chemical classes were associated with small increases (3-7%) in risk for preterm birth; associations were stronger for female offspring. We did not find associations between term low birthweight and exposures to pesticides other than for myclobutanil (OR: 1.11; 95% CI: 1.04-1.20) and possibly pyrethroids as a class. Our improved exposure assessment revealed that first and second trimester exposures to pesticides were associated with preterm delivery but few affected term low birthweight.

With the widespread of embedded sensing capabilities of mobile devices, there has been unprecedented development of context-aware solutions. This allows the proliferation of various intelligent applications such as those for remote health and lifestyle monitoring, intelligent personalized services, etc. However, activity context recognition based on multivariate time series signals obtained from mobile devices in unconstrained conditions is naturally prone to imbalance class problems. This means that recognition models tend to predict classes with the majority number of samples whilst ignoring classes with the least number of samples, resulting in poor generalization. To address this problem, we propose to augment the time series signals from inertia sensors with signals from ambient sensing to train deep convolutional neural networks (DCNN) models. DCNN provides the characteristics that capture local dependency and scale invariance of these combined sensor signals. Consequently, we developed a DCNN model using only inertial sensor signals and then developed another model that combined signals from both inertia and ambient sensors aiming to investigate the class imbalance problem by improving the performance of the recognition model. Evaluation and analysis of the proposed system using data with imbalanced classes show that the system achieved better recognition accuracy when data from inertial sensors are combined with those from ambient sensors such as environment noise level and illumination, with an overall improvement of 5.3% accuracy.

Temperature is a critical factor that influences the proliferation of pathogens in hosts. The impact of temperature on pathogens is commonly explored in controlled and constant temperatures. Experiments under varying environmental temperature are becoming more frequent, however, testing every temperature scenario à la carte is unachievable. One example of this is the human pathogen Vibrio parahaemolyticus (Vp) in oysters. Here, a predictive model was developed for predicting the growth of Vp in oysters under varying ambient temperature. The model was fitted and evaluated against data from experiments studying growth and inactivation of Vp in oysters at eight constant temperatures. Once evaluated, Vp dynamics in oysters were estimated at different post-harvest varying temperature scenarios affected by water and air temperature, and different ice treatment timing. The model performed adequately under varying temperature, reflecting that (i) increasing temperature, particularly in hot summers, favors a rapid Vp growth in oysters, resulting in a very high risk of gastroenteritis in humans after consumption of a serving of raw oysters, (ii) pathogen inactivation due to day/night oscillations, and more evidently, due to ice treatments, (iii) ice treatment is much more effective limiting risk of illness when applied immediately onboard compared to dockside. The model results to be a promising tool for improving the understanding of the Vp-oyster system and support studies on public health impact of pathogenic Vp associated with raw oyster consumption. Although robust validation of the model predictions is needed, initial results and evaluation show the potential of the model to be easily modified to match similar systems where the temperature is a critical factor shaping the proliferation of pathogens in hosts.

The impact of cyclic heat stress (CHS) and lighting events on pig feeding behavior (FB) was investigated. The FB of 90 gilts was recorded in real time under two ambient temperatures (AT): thermoneutrality (TN, 22 °C) or CHS (22°/35 °C). The day was divided into four periods: PI (06-08 h); PII (08-18 h); PIII (18-20 h); and PIV (20-06 h). Automatic and Intelligent Precision Feeders recorded each feed event for each pig. An estimated meal criterion (49 minutes) was used to calculate the FB variables. Feed behavior in both ATs followed a circadian pattern. The CHS reduced the feed intake by 6.9%. Pigs prioritized feed intake during the coolest hours of the day; however, nocturnal cooling did not allow the pigs to compensate for the reduced meal size due to CHS. The highest meal size and most of the meals were observed during the lighting-on period. Pigs reduced their interval between meals during periods II and III. The lighting program increased the meal size when the lights were switched on and reduced the meal size when the lights were switched off. Thus, the dynamics of the FB were largely influenced by AT, while the meal size was affected by the lighting program.

Drivers of L3 automated vehicles (AVs) are not required to continuously monitor the AV system. However, they must be prepared to take over when requested. Therefore, it is necessary to design an in-vehicle environment that allows drivers to adapt their levels of preparedness to the likelihood of control transition. This study evaluates ambient in-vehicle lighting that continuously communicates the current level of AV reliability, specifically on how it could influence drivers' take-over performance and mental workload (MW). We conducted an experiment in a driving simulator with 42 participants who experienced 10 take-over requests (TORs). The experimental group experienced a four-stage ambient light display that communicated the current level of AV reliability, which was not provided to the control group. The experimental group demonstrated better take-over performance, based on lower vehicle jerks. Notably, perceived MW did not differ between the groups, and the EEG indices of MW (frontal theta power, parietal alpha power, Task-Load Index) did not differ between the groups. These findings suggest that communicating the current level of reliability using ambient light might help drivers be better prepared for TORs and perform better without increasing their MW.

In CCS projects, the transportation of CO₂ by ship can be an attractive alternative to transportation using a pipeline, particularly when the distance between source and disposal location is large. However, the energy consumption of the liquefaction process can be significant, making the selection of an energy-efficient design an important factor in the minimization of operating costs. Since the liquefaction process operates at low temperature, its energy consumption will vary with ambient temperature, which could be a factor that influences the trade-off point between pipelines and shipping in different geographic locations. A consistent set of data showing the relationship between energy consumption and cooling temperature is therefore potentially useful to CCS system modelling. This study compares the performance of a wide range of CO₂ liquefaction schemes. It applies a methodical approach to the optimization of process operating parameters and studies performance across a range of operating temperatures. A set of data for the minimum energy consumption cases is presented. The main findings are that open-cycle CO₂ processes often offer minimum energy consumption; NH₃ based schemes often offer better performance at higher ambient temperatures; and that for the cooling temperature range 15 to 50 °C, the energy consumption for the best performing liquefaction process rises by around 40%.

In hospitals and smart nursing homes, ambient-intelligent care rooms are equipped with many sensors. They can monitor environmental and body parameters, and detect wearable devices of patients and nurses. Hence, they continuously produce data streams. This offers the opportunity to collect, integrate and interpret this data in a context-aware manner, with a focus on reactivity and autonomy. However, doing this in real-time on huge data streams is a challenging task. In this context, cascading reasoning is an emerging research approach that exploits the trade-off between reasoning complexity and data velocity by constructing a processing hierarchy of reasoners. Therefore, a cascading reasoning framework is proposed in this paper. A generic architecture is presented allowing to create a pipeline of reasoning components hosted locally, in the edge of the network, and in the cloud. The architecture is implemented on a pervasive health use case, where medically diagnosed patients are constantly monitored, and alarming situations can be detected and reacted upon in a context-aware manner. A performance evaluation shows that the total system latency is mostly lower than 5 seconds, allowing for responsive intervention by a nurse in alarming situations. Using the evaluation results, the benefits of cascading reasoning for healthcare are analyzed.

Traffic congestion is one of the foremost problems confronted by the urban and suburban tenants of today. Traffic congestion increases vehicle emissions and degrades air quality. Urban planners and policy makers have consequently been always investigating choices to alleviate traffic congestion and to enhance air quality. Teleworking is one option that has received significant consideration and has been studied in the recent past. The aim of the study is to explore the relationship between teleworking, air quality and traffic in Switzerland. The analysis relies on panel individual and household level data over the period 2002-2013. We examine five main air pollutants; the sulphur dioxide (SO₂), the ground-level ozone (O₃) the nitrogen dioxide (NO₂), the carbon monoxide (CO) and the particulate matter less than 10 microns (PM₁₀). Based on the fixed effects estimates, teleworking reduces traffic volume by 1.9 per cent. Furthermore, the reduction observed on air pollution is higher for NO₂, CO and PM₁₀ ranging between 3.3-3.7 per cent, followed by O₃ at 2.3 per cent and SO₂ at 2.1 per cent. According to instrumental variable (IV) approach and the two stage least squares (2SLS) method, the effect is higher ranging between 2.6-4.1 per cent. The respective reduction on traffic becomes 2.7 per cent. Overall, the main concluding remark of the study is that teleworking can be a promising tool for urban planning and development, focusing at the traffic volume reduction, and the air quality improvement. Additional policy implications of teleworking and its beneficial effects for the society are further discussed.

PM_0.1 (particles diameter ≤ 0.1 µm), nanoparticles (NPs), and ultrafine particles (UFPs), were interchangeably used in the scientific communities. PM_0.1 originated from both natural and human sources. However, investigations of PM_0.1 and its effects on the environment, visibility, and human health risk to understand the levels of air pollution, sources, and impacts in South East Asia (SEA) countries continue to be lacking. The concentration of PM_0.1 in most SEA countries are much worse than those in western countries environment. A further motivation of this reviewed article is to provide a critical synthesis of the current knowledge and study of ambient PM_0.1 in SEA cities. The main influence of characteristics of PM_0.1 appears to be local sources including biomass burning and motor vehicles. Continuous monitoring of PM_0.1 in terms of both mass and number concentration should be further understood. A critical review is of great importance to facilitating air pollution control policies and predicting the behavior of PM_0.1 in SEA.

No doubt pollution is a global problem which must be holistically tackled. In doing this, adequate knowledge of the sources of pollution is important, therefore the aim of this paper is to review source apportionment with reference to top-down and bottom-up methods. In this paper, dispersion modeling, emissions inventory, and sampling methods were discussed. Also, analytical methods involved in top-down source apportionment were mentioned. The two techniques are needed to evaluate pollutants and their sources. Based on these two approaches, pollution control strategy would be developed and decisions can be made in deciding the right approach to solve or reduce the pollution problems.

Pulmonary hypertension (PH) has a high mortality, and few treatment options. Adaptive immune mediators of PH in mice challenged with antigen/particulate matter (antigen/PM) has been the focus of our prior work. We identified key roles of type 2 and type 17 responses in C57BL/6 mice. Here, we focused on type 2 response related cytokines, specifically Resistin-like-molecule (RELM)α, a critical mediator of hypoxia-induced PH. Because of strain differences in the immune responses to type 2 stimuli, we compared C57BL/6J and BALB/c mice. A model of intraperitoneal antigen sensitization with subsequent, intranasal challenges with antigen/PM (ovalbumin and urban ambient PM2.5) or saline was used in C57BL/6 and BALB/c wild type or RELMα-/- mice. Vascular remodeling was assessed by histology, right ventricular (RV) pressure, RV weights and cytokines were quantified. Upon challenge with antigen/PM2.5, both C57BL/6 and BALB/c mice developed pulmonary vascular remodeling; these changes were more prominent in the C57BL/6 strain. Compared to wild type mice, RELMα-/- had significantly reduced pulmonary vascular remodeling in BALB/c, but not in C57BL/6 mice. RV weights, RV IL-33 and RV ST2-IL-33-receptor were significantly increased in BALB/c wild type mice, but not in BALB/c-RELMα-/- or in C57BL/6-wild type or C57BL/6-RELMα-/- mice. RV systolic pressures (RVSP) were higher in BALB/c compared to C57BL/6J mice, and RELMα-/- were not different from their respective wild type controls. In BALB/c mice, RELMα was a key contributor to antigen/PM2.5 induced pulmonary vascular remodeling, RV thickening and RV cytokine responses, highlighting the significance of the genetic background. The RELMα-/- animals demonstrated significantly decreased expression of RELMβ and RELM which makes these mice comparable to a situation where human RELMα levels would be significantly modified, as humans only have one RELM molecule.

The previous studies on the diversion pipe of pumped storage power stations (PSPS) primarily focused on numerical simulations of pulsating pressure propagation within the pipe and its inducing factors. However, there was a lack of field monitoring and analysis of measured data to support surface ambient vibration, resulting in insufficient credibility and practicality of the numerical results. Based on ambient monitoring and data analysis, this paper examines the factors contributing to the ambient vibration of the water diversion pipeline in Changlongshan (CLS) PSPS. It is concluded that: (1) The primary source of vibration originates from units operation-induced ambient vibrations; (2) Vibration during pumping conditions exceeds that during power generation conditions; (3) The ground measuring point's vibration acceleration primarily depends on the distance from the vibration source; (4) Different types of units have varying effects on water diversion pipeline vibrations.

For the first time, it is shown that inhaled ambient air-dust particles settled in the human lower respiratory tract induce lung calcification. Chemical- and mineral compositions of pulmonary calcium precipitates in the lung right lower-lobe (RLL) tissues of 12 individuals who lived in Upper Silesia Conurbation in Poland and who had died from causes not related to lung disorder were determined by transmission- and scanning electron microscopy. Whereas calcium salts in lungs are usually reported as phosphates, calcium salts precipitated in RLL are almost exclusively carbonates, i.e. Mg-calcite and calcite. These constitute 37% of 1652 mineral particles examined. Mg-calcite predominates in the submicron size range with the MgCO3 content up to 50 mol%. Magnesium plays a significant role in the lung mineralization, a fact so far overlooked. The calcium phosphate (hydroxyapatite) content in RLL is negligible. The predominance of carbonates is explained by increased CO2 fugacity in RLL. Carbonates enveloped inhaled mineral-dust particles, including uranium-bearing oxides, quartz, aluminosilicates, and metal sulfides. Three possible pathways for the carbonates precipitation on the dust particles are postulated: (1) precipitation of amorphous calcium carbonate (ACC) followed by its transformation to calcite; (2) precipitation of Mg-ACC followed by its transformation to Mg-calcite; (3) precipitation of Mg-free ACC causing a localized relative enrichment in Mg ions and subsequent heterogeneous nucleation and crystal growth of Mg-calcite. The actual number of inhaled dust particles may be significantly greater than observed because of the masking effect of the carbonate coatings. There is no simple correlation between smoking habit and lung calcification.

Air pollution is a man-made environmental-related problem and has importance globally among all environmental issues. It is described as an atmospheric situation in which several components appear at high attention above their ambient level and generate a quantifiable effect on vegetation, animals, and people. Air pollution and its control are a universal problem and have become an issue of great trouble for us in current years. However, monitoring and measurement of the concentration of air pollutants are most difficult in assessment to monitoring other components in the environment. Air pollutants are transported to polar regions by different mechanisms such as long-range atmospheric transport or grasshopper effects and via anthropogenic activities. After reaching the polar regions, they settle down and remain as such for a long-time due to their persistent nature. They can distress the environment and wildlife of the polar regions. Generally, dangerous chemicals may cause a risk of well-being effects, whereas lethal pollutants focus on one physiological reaction. We reviewed the available information on air pollution (occurrence, sources, and harmful effects) in the polar regions.

Shenzhen is China’s top ten clean air city and the cleanest air megacity. Even so, epidemiologic studies have shown ambient air pollution had significant adverse impacts on human health in this less polluted city. In this study, the concentrations of six criteria air pollutants (PM2.5, PM10, O3, NO2, SO2, and CO) from 2014 to 2017 were analyzed and compared to thresholds of both national and international air quality standards. The results showed concentrations of all air pollutants were below target values of current national air quality standard, but levels of particulate matter (PM) and O3 were still much higher than the recommended levels by the World Health Organization. Within national air quality standards, the number of over-limit days was rare with few variations between highly polluted and low pollution areas. The air quality improvement was slowing down recently. Our results suggest annual and daily thresholds for PM are too loose for air quality improvement in Shenzhen. Hence, we call for evaluation and establishment of tougher air quality standard.

The new Internet of Things (IoT) applications are enabling the development of projects that help monitoring people with different diseases in their daily lives. Alzheimer’s is a disease that affects neurological functions and needs support to maintain maximum independence and security of patients during this stage of life, as the cure and reversal of symptoms have not yet been discovered. The IoT-based monitoring system provides the caregivers’ support in monitoring people with Alzheimer’s Disease (AD). This paper presents an ontology-based computational model which receives physiological data from external IoT applications, allowing to identify of potentially dangerous behaviors for patients with AD. The main scientific contribution of this work is the specification of a model focusing on Alzheimer’s disease using the analysis of Context Histories and Context Prediction, which considering the state of the art, it is the only one that uses analysis of Context Histories to perform predictions. The research also proposes a simulator to generate activities of the daily life of patients allowing the creation of datasets. These datasets were used to evaluate the contributions of the model and were generated according to the standardization of the ontology. The simulator generated 1025 scenarios applied to guide the predictions, which achieved average accurary of 97.44%. The experiments also allowed the learning of 20 relevant lessons on technological, medical and methodological aspects of DCARE that are recorded in this article.

Grazing incidence X-Ray Diffraction spectroscopy was employed to characterize crystallinity of Iron, Nickel, Copper and Tungsten, prepared by sparking discharge process in presence of 0.4 T magnetic field at ambient temperature 25 °C. Iron thin film preserved crystallinity even after one year of ageing. Nickel exhibit higher crystallinity when sparked in nitrogen gas flow from the one sparked in oxygen. Tungsten was successfully crystalized after just 40 minutes of sparking inside of magnetic field.

Continuous in-home monitoring of older adults living alone aims to improve their quality of life and independence, by detecting early signs of illness and functional decline or emergency conditions. To meet requirements for technology acceptance by seniors (unobtrusiveness, non-intrusiveness, privacy-preservation), this study presents and discusses a new smart sensor system for the detection of abnormalities during daily activities, based on ultra-wideband radar providing rich, not privacy-sensitive, information useful for sensing both cardiorespiratory and body movements, regardless of ambient lighting conditions and physical obstructions (through-wall sensing). The radar sensing is a very promising technology, enabling the measurement of vital signs and body movements at a distance, and thus meeting both requirements of unobtrusiveness and accuracy. In particular, impulse-radio ultra-wideband radar has attracted considerable attention in recent years thanks to many properties that make it useful for assisted living purposes. The proposed sensing system, evaluated in meaningful assisted living scenarios by involving 30 participants, exhibited the ability to detect vital signs, to discriminate among dangerous situations and activities of daily living, and to accommodate individual physical characteristics and habits. The reported results show that vital signs can be detected also while carrying out daily activities or after a fall event (post-fall phase), with accuracy varying according to the level of movements, reaching up to 95% and 91% in detecting respiration and heart rates, respectively. Similarly, good results were achieved in fall detection by using the micro-motion signature and unsupervised learning, with sensitivity and specificity greater than 97% and 90%, respectively.

The development effect of water flooding in ultra-low permeability reservoir was poor due to its poor physical property and high shale content, the experimental study of air flooding which help to complement producing energy was carried out. Based on the Accelerating Rate Calorimeter experimental results, the crude oil of N block in L oilfield can produce low-temperature oxidation reaction, which was the basic condition of air flooding. Three groups of experiment natural cylinder core were designed for oil displacement, water flooding and air flooding were used respectively, and the relationship of differential pressure, oil recovery, injection capacity with injection volume was investigated. It has been showed on the result that the recovery efficiency improved sharply than water flooding, the effect of depressurization and augmented injection was obvious, and the air displacement was validation.

Worldwide emission standards are now required to cover engine operation under extreme ambient conditions, which affect the raw emissions and the efficiency of the exhaust aftertreatment systems. These regulations also target new combustion technologies for decarbonization, such as neat hydrogen (H2) combustion or dual-fuel strategies, which involve a challenge to the analysis of exhaust aftertreatment systems requirements and performance. This work addresses the impact of high altitude and low ambient temperature conditions on the reactivity of an oxidation catalyst in the presence of H2. A reaction mechanism is proposed to cover the main conversion paths of CO, HC, and H2, including the formation and consumption of high-energy surface reaction intermediates. The mechanism has been implemented into a faster-than-real-time reduced-order model for multi-layer washcoat honeycomb catalytic converters. The model was utilized to investigate the effect of H2 concentration on the reactivity of CO and HC within the catalyst under various operating and ambient conditions. By applying the model and examining the selectivity towards different reaction pathways in the presence H2, insights into surface intermediates and reactivity across different cross-sections of the monolith were obtained. This analysis discusses the underlying causes of reactivity changes promoted by H2 and its relative importance as a function of driving boundary conditions.

Chronic heat stress (CHS) has been exerting great pressure on the poultry industry due to the global warming. CHS-induced negative impacts deeply change the physiology, metabolism, egg production and meat quality of ducks. To reduce the increasing economic loss, different environmental strategies have been adopted. Here, we comprehensively compared three rearing modes for Cherry-Valley ducks (CVds) mainly by changing the environmental temperature. Plus, the transcriptome analysis and physiological anatomy were implied to investigate the underlying molecular biology and pneumonocyte dynamics. It turns out that the CVds affected by CHS have poor growth performance and bad carcass traits. In addition, the irreversible damage caused by CHS in the lung tissue of CVds was observed. Furthermore, several potential genes related to CHS have been found, such as HSPA8, IGF1, FGFR1, ACSL3, ACSL6, NR1H3 and GAPDH. This study strongly indicates the severe injury of CHS from the high-temperature environment and points out one of the adopting directions for duck rearing.

Several studies have identified a relationship between air pollution and depression, particularly in relation to fine particulate matter (PM2.5) exposure. However, the strength of this association appears to be moderated by variables such as age, gender, genetic vulnerability, physical activity and climatic conditions, and has not been assessed at a cross-national level to date. The current study examines the association between the prevalence of depression in each country, based on the most recent Global Burden of Disease Study data, and the average national level of PM2.5 based on the World Health Organization’s database. The observed associations were adjusted for age, gender, level of physical activity, income, education, population density, climate, and type of depression. It was observed that there was a modest but significant positive correlation between PM2.5 level and the prevalence of depression even after adjusting for the above confounders. This association was more marked above a certain threshold and applied chiefly to major depressive episodes. These findings are of significant public health importance in terms of preventive strategies aimed at reducing the population-level burden of depression.

Exposure to traffic-related air pollution is linked with acute alterations in blood pressure (BP). We examined the cumulative short-term effect of black carbon (BC) exposure on systolic (SBP) and diastolic (DBP) BP and assessed effect modification by participant characteristics. SBP and DBP were repeatedly measured on 152 traffic enforcers. Using a linear mixed-effects model with random intercepts, quadratic (QCDL) and cubic (CCDL) constrained distributed lag models were fitted to estimate the cumulative effect of BC concentration on SBP and DBP during the 10-hours (daily exposure) and 7-days (weekly exposure) before the BP measurement. Ambient BC was related to increased BP with QCDL models. An interquartile range change in BC cumulative during the 7-days before the BP measurement was associated with increased BP [1.2% change in mean SBP, 95% confidence interval (CI), 0.1 to 2.3; and 0.5% change in mean DBP, 95% CI, –0.8 to 1.7]. Moreover, the association between the 10-hours cumulative BC exposure and SBP was stronger for females (4.0% change, 95% CI: 2.1–5.9) versus males, and for obese (2.9% change, 95% CI: 1.0–4.8) vs. non-obese traffic enforcers. Short-term cumulative exposure to ambient traffic-related BC could bring about cardiovascular diseases through mechanisms involving increased BP.

Walking School Buses (WSBs) provide a safe alternative to being driven to school. Children benefit from the contribution the exercise provides towards their daily exercise target, it gives children practical experience with respect to road safety and helps to relieve traffic congestion around the entrance to their school. Walking routes are designed largely based in road safety considerations, catchment need and the availability of parent support. However, little attention is given to the air pollution exposure experienced by children during their journey to school, despite the commuting microenvironment being an important contributor to a child’s daily air pollution exposure. This study aims to quantify the air pollution exposure experienced by children walking to school and those being driven by car. A school was chosen in Bradford, UK. Three adult participants carried out the journey to and from school each carrying a P-Trak ultrafine particle (UFP) count monitor. One participant travelled the journey to school by car while the other two walked, each on opposite sides of the road for the majority of the journey. Data collection was carried out over a period of two weeks, for a total of five journeys to school in the morning and five on the way home at the end of the school day. Results of the study suggest that car commuters experience lower levels of air pollution dose due to lower exposures and reduced commute times. The largest reductions in exposure for pedestrians can be achieved by avoiding close proximity to traffic queuing up to intersections, and, where possible, walking on the side of the road opposite the traffic, especially during the morning commuting period. Major intersections should also be avoided as they were associated with peak exposures. Steps to ensure that the phasing of lights is optimized to minimize pedestrian waiting time would also help reduce exposures. If possible, busy roads should be avoided altogether. By the careful design of WSB routes, taking into account air pollution, children will be able to experience the benefits that walking to school brings while minimizing their air pollution exposure during their commute to and from school.

Air corridors are an integral part of the advanced air mobility infrastructure. They are the virtual highways in the sky for transportation of people and cargo in the controlled airspace at an altitude of around 1000 ft. to 2000 ft. above the ground level. This paper presents fundamental insights into the design of air corridors with high operational efficiency as well as zero collisions. It begins with the definitions of air cube, skylane or track, intersection, vertiport, gate, and air corridor. Then, a multi-layered air corridor model is proposed. Traffic at intersections is analyzed in detail with examples of vehicles turning in different directions. The concept of capacity of an air corridor is introduced along with the nature of distribution of locations of vehicles in the air corridor and collision probability inside the corridor are discussed. Finally, the results of simulations of traffic flows are presented.

Photonic sensors are innovative devices that leverage the principles of light-matter interaction to enable precise and efficient detection of various physical parameters. These sensors operate by exploiting the interaction between photons, the fundamental particles of light, and matter. The light propagates through an optical waveguide, and a portion of the electromagnetic field extends beyond the waveguide surface, forming the evanescent field. This evanescent field interacts with the surrounding medium, allowing for highly sensitive detection of changes in the refractive index or properties of nearby substances. The underlying concept involves the modulation of light properties, such as intensity, wavelength, or phase, when it interacts with a target substance or undergoes changes in the surrounding environment. The advancements in photonic sensor technology have paved the way for enhanced sensitivity, selectivity, and miniaturization, making them invaluable tools in diverse industries. The ability to harness light-matter interactions for sensing purposes not only facilitates highly sensitive measurements but also allows for non-intrusive and remote monitoring, contributing to the evolution of smart and connected systems. In this overview, the material platforms and waveguide structures are explored that can make highly sensitive photonic devices applied to gas and biosensing applications.

Deep neural networks (DNNs) have gained prominence in addressing regression problems, offering versatile architectural designs that cater to various applications. In the field of earthquake engineering, seismic response prediction is a critical area of study. Simplified models such as single-degree-of-freedom (SDOF) and multi-degree-of-freedom (MDOF) systems have traditionally provided valuable insights into structural behavior, known for their computational efficiency facilitating faster simulations. However, these models have notable limitations in capturing the nuanced nonlinear behavior of structures and the spatial variability of ground motions. This study focuses on leveraging ambient vibration (AV) measurements of buildings, combined with earthquake (EQ) time-history data, to create a predictive model using a neural network (NN) in image format. The primary objective is to predict a specific building's earthquake response accurately. The training dataset consists of 1,197 MDOF 2D shear models, generating a total of 32,319 training samples. To evaluate the performance of the proposed model, termed MLPER (Machine Learning based Prediction of building structures' Earthquake Response), several metrics are employed. These include mean absolute percentage error (MAPE) and mean deviation angle (MDA) for comparisons in the time domain. Additionally, we assess magnitude-squared coherence values and phase differences (Δφ) for comparisons in the frequency domain. This study underscores the potential of MLPER as a reliable tool for predicting building earthquake response, addressing the limitations of simplified models. By integrating AV measurements and EQ time-history data into a neural network framework, MLPER offers a promising avenue for enhancing our understanding of structural behavior during seismic events, ultimately contributing to improved earthquake resilience in building design and engineering.

The Human immunodeficiency virus-1 (HIV-1) matrix (MA) domain is involved in the highly regulated assembly process of the virus particles that occur at the host cell’s plasma membrane. High-resolution structures of the MA domain determined using cryo X-ray crystallography have provided initial insights into the possible steps in the viral assembly process. However, these structural studies have relied on large and frozen crystals in order to reduce radiation damage caused by the intense X-rays. Here, we report the first XFEL study of the HIV-1 MA domain’s interaction with inositol hexaphosphate (IP6), a phospholipid headgroup mimic. We also describe the purification, characterization and microcrystallization of two MA crystal forms obtained in the presence of IP6. In addition, we describe the capabilities of serial femtosecond X-ray crystallography (SFX) using X-ray free-electron laser (XFEL) to elucidate the diffraction data of MA-IP6 complex microcrystals in liquid suspension at ambient temperature. Two different microcrystal forms of MA-IP6 complex both diffracted to beyond 3.5 Å resolution, demonstrating the feasibility of using SFX to study the complexes of MA domain of HIV-1 Gag polyprotein with IP6 at near-physiological temperatures. Further optimization of the experimental and data analysis procedures will lead to better understanding of the MA domain of HIV-1 Gag and IP6 interaction at high resolution and provide basis for optimization of the lead compounds for efficient inhibition of the Gag protein recruitment to the plasma membrane prior to virion formation.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

The interest in flying wings dates as far the early years of the aviation age. Over the 20th century, numerous attempts were made to investigate the feasibility of the concept, which demonstrated numerous early benefits: increased aerodynamic efficiency, reduced fuel consumption and lower noise and pollutant emissions compared to conventional tube and wing aircraft. However, major technical challenges prevented that type of design from entering mass production, especially with regards to structural design and manufacturing, stability and control and ride quality. In the 1990’s, a new concept, the blended wing body (BWB), was created to alleviate some of the concerns of flying wings while maintaining increased efficiency. Despite the promise, technical hurdles once again proved to be a deal breaker, and as of 2024, the only flying wing to enter serial production is the B-2 Spirit, an extremely complex and expensive aircraft. Thirty years later, as the world is quickly transitioning towards cleaner energy, the interest in the blended wing body has been renewed. The latest technological advancements in the aerospace industry should make the development of the BWB more plausible, however passenger comfort issues remain. Surprisingly, the BWB development may come from an unexpected application: as a tanker aircraft. As the U.S. Air Force is seeking a replacement to hundreds of aging tankers, a startup company was recently funded to develop the concept and build a prototype. In this study, we explore the history of blended designs from its early days, highlighting its opportunities and challenges – and why the design is an intriguing fit for application as a tanker aircraft.

This comprehensive critical review shows how green buildings and energy optimization solutions improve indoor air quality as well as environmental quality (IEQ) and human health. Electricity-efficient green buildings create a better indoor atmosphere and save electricity. Green buildings improve occupant well-being through IAQ, thermal comfort, acoustics, and lighting. Renewable energy, green construction materials, and intelligent technologies increase sustainability and reduce environmental impact. Environmental hazards, architectural design, and societal variables can improve indoor air quality and subsequently reduce health risks linked with poor air quality. The evaluation highlights the pros and cons of low-cost IAQ sensors and equipment. These devices provide valuable insights, but calibration and validation using reference equipment are necessary to ensure accuracy and reliability. Architects, engineers, environmentalists, and policymakers are essential in creating green buildings with high IEQ. Prioritizing occupant comfort, health, and productivity ensures a sustainable and healthy future for future generations. However, continual monitoring and research are needed to improve green building practices and overcome construction problems. Intelligent models for continual on-field calibration of low-cost sensors may improve performance. Green buildings benefit occupants and the environment by optimizing energy use and using IAQ monitoring technologies.

This article examines air sampling as an environmental surveillance strategy for early pathogen detection and offers a preliminary comparison of air and wastewater surveillance. Air sampling involves collecting bioaerosols to analyze the microbial composition of the air, utilizing techniques like PCR and metagenomic sequencing. Air sampling appears especially promising for detecting respiratory pathogens and highly transmissible pandemic agents, as these spread primarily via aerosols and droplets. The article details various air sampling techniques, their efficiency, and practical considerations, categorizing them into filtration, impaction, impingement, electrostatic precipitation, and condensation methods. It also explores the composition of airborne microbes, emphasizing the low concentration of viral nucleic acids and the challenges this poses for metagenomic sequencing. The selection of sampling locations, including indoor environments and airplanes, is discussed as critical for effective pathogen detection. Finally, the article contrasts air and wastewater sampling, concluding that while both methods should ideally be explored as layered defenses, air sampling does not collectively appear more promising than wastewater sampling.

Urban air quality is increasingly becoming a cause for concern for the health of the human population. The poor air quality is already wreaking havoc in major cities of the world, where serious health issues and reduction of average human life by a factor of years are reported. The air quality in developing countries can become worse as they undergo development. The urban air quality varies non-linearly depending upon the various factors such as land use, industrialization, waste disposal, traffic volume, etc. To address this problem, it is necessary to look at the plethora of available literature from multiple perspectives such as types and sources of pollutants, meteorology, urban mobility, urban planning and development, health care, economics, etc. In this paper, we provide a comprehensive survey of the state-of-the-art in urban air quality. We first review the fundamental background on air quality and present the emerging landscape of urban air quality. We then explore the available literature from multiple urban air quality measurement projects and provides the insights uncovered in them. We then take a look at the sources that are significantly contributing to polluting the air quality. Finally, we highlight open issues and research challenges in dealing with urban air pollution.

Environment pollution is the major problem for all the sectors. In environment pollution there are different types of pollution is included such as air pollution, water pollution, soil pollution etc. In these types of pollution most of it is air pollution. There are many reasons for pollution of air. Human advance in science but one of the major draw backs of science is the pollution of air rapidly. Air pollution is injurious to health. Every year a large number of people died for the effects of air pollution. It can be improved in many ways among these ways technology upgradation plays a major role here. There are various method that prevent air pollution. Many researchers tried and is trying to prevent the air pollution in many ways. In this review paper I summarise the existing research on different ways for preventing air pollution in addition I will discuss the gaps and future aspect on this topic.

Pyrolysis is a combustion process of woody biomass conducted under low or no oxygen conditions. New innovations and the need to limit open burning has resulted in numerous mobile and fixed plant pyrolysis methods that burn a variety of woody residues. Production technologies that reduce the need for open burning, the main source of potential pollutants, fall under the regulations in the Clean Air Act of 1990. This Act is the legal instrument to regulate air pollution at its source across the United States of America and it is implemented and enforced through the Environmental Protection Agency, in coordination with sister agencies. One newer innovation for reducing woody residues and emissions is an air curtain incinerator. Currently, the Clean Air Act regulates stationary solid waste incinerators, and this is also applied to mobile air curtain incinerators burning woody biomass. However, other woody biochar production methods (e.g., flame cap kilns) are not subject to these regulations. Discrepancies in the interpretation of definitions related to incineration and pyrolysis and the myriad of differences related to stationary and mobile air curtain incinerators, type of waste wood from construction activities, forest residues, and other types of clean wood make the permitting regulations confusing as permits can vary by jurisdiction. This review summarizes the current policies, regulations, and directives related to in-woods biochar production and the required permits.

In this work, a novel heterojunction based on ZnSnO3/ZnO nanofibers was prepared using electrospinning method. The crystal, structural and surface compositional properties of sample based on ZnSnO3 and ZnSnO3/ZnO composite nanofibers were investigated by X-ray diffractometer (XRD), Scanning electron microscope (SEM), X-ray photoelectron spectrometer (XPS) and Brunauer-Emmett-Teller (BET). Compared to pure ZnSnO3 nanofibers, the ZnSnO3/ZnO heterostructure nanofibers display high sensitivity and selectivity response with fast response towards ethanol gas at low operational temperature. The sensitivity response of sensor based on ZnSnO3/ZnO composite nanofibers were 19.6 towards 50 ppm ethanol gas at 225°C, which was about 1.5 times superior than that of pure ZnSnO3 nanofibers, which can be owed mainly to the presence of oxygen vacancies and the synergistic effect between ZnSnO3 and ZnO.

In this study, the relationship between air diffusivity and permeability in cementitious materials was investigated. First, we derived an equation to correlate air diffusivity and permeability in a straight circular tube. Then, we reviewed existing studies that measured both air diffusivity and permeability and compared reported data and calculated values to verify the applicability of the derived equation to cementitious materials. Although a correction factor was not used, the two sets of data showed good agreement quantitatively. This indicates that the derived equation can be applied to cementitious materials including concrete, and measured air diffusivity can be converted to permeability of concrete and vice versa using the derived equation.

This paper investigates the effects of air void topology on hydraulic conductivity in asphalt mixtures with porosity in the range 14%-31%. Virtual asphalt pore networks were generated using the Intersected Stacked Air voids (ISA) method, with its parameters being automatically adjusted by the means of a differential evolution optimisation algorithm, and then 3D printed using transparent resin. Permeability tests were conducted on the resin samples to understand the effects of pore topology on hydraulic conductivity. Moreover, the pore networks generated virtually were compared to real asphalt pore networks captured via X-ray Computed Tomography (CT) scans. The optimised ISA method was able to generate realistic 3D pore networks corresponding to those seen in asphalt mixtures in term of visual, topological, statistical and air void shape properties. It was found that, in the range of porous asphalt materials investigated in this research, the high dispersion in hydraulic conductivity at constant air void content is a function of the average air void diameter. Finally, the relationship between average void diameter and the maximum aggregate size and gradation in porous asphalt materials was investigated.

International literature data report that the increase of infectious risk may be due to heating, ventilation and air conditioning (HVAC) systems contaminated by airborne pathogens. Moreover, the presence of complex rotating dehumidification wheels (RDWs) may complicate the cleaning and disinfection procedures of the HVAC systems. We evaluated the efficacy of a disinfection strategy applied to the RDW of two hospitals HVAC systems. Hospitals have 4 RDW systems related to the surgical areas (SA1 and SA2) and to the intensive and sub-intensive cares (IC and sIC). Microbiological air and surfaces analysis were performed in HVAC systems, before and after the disinfection treatment. Hydrogen peroxide (12%) with silver ions (10 mg/L) was aerosolized in all the air sampling points, located close to the RDW device. After the air disinfection procedure, reductions of total microbial counts at 22°C and fungi were achieved in SA2 and IC HVAC systems. An Aspergillus fumigatus contamination (6 CFU/500L), detected in one air sample collected in the IC HVAC system, was eradicated after the disinfection. Surface samples proved a good microbiological quality. Results suggest the need of a disinfection procedure aimed to improve the microbiological quality of the complex HVAC systems, mostly in surgical and intensive care areas.

Hydrogen used as an energy carrier can provide an important route to the decarbonization of energy supplies. However, realizing this opportunity requires a significant increase in both production and transportation capacity. Part of the increase in transportation capacity could be provided by the shipping of liquid hydrogen, but this introduces an energy-intensive liquefaction step into the supply-chain. The energy required for liquefaction can be reduced by developing improved process designs, but since all low-temperature processes are affected by the available heat-sink temperature, local ambient conditions will also affect the energy penalty. This work studies how the energy consumption associated with liquefaction varies with heat-sink temperature through the optimization of design parameters for a typical next-generation hydrogen liquefaction process. The results show that energy consumption increases by around 20%, across the cooling temperature range 5 to 50 °C. Considering just the range 20 to 30 °C there is a 5% increase, illustrating the significant impact ambient temperature can have on energy consumption.

Based on a constant volume combustion chamber, the initial ambient pressure effect on combustion performance and flame propagation of the active and passive pre-chamber ignition systems were studied. Compared with the passive pre-chamber, the active pre-chamber can significantly expand the lean combustion limit, enhance the ignition and combustion performance, and speed up the combustion of the main combustion chamber. At slightly lean combustion conditions, the heat release performance has a positive correlation with the initial ambient pressure. As the premixed λ increases, the heat release performance and the initial ambient pressure begin to become negatively correlated. Ignition delay can be minimized by controlling the excess air coefficient in the pre-chamber close to the stoichiometric ratio. The high ambient pressure in the constant volume chamber greatly reduces the mixture entrainment ability of the jet flame at lean combustion conditions, thereby reducing the combustion speed and peak heat release rate.

The purpose of this study is to characterize atmospheric pollution and its sources in two West African urban sites during the dry season (January 2009 in Bamako, Mali, and December 2009 in Dakar, Senegal). Particulate Matter (PM) source apportionment was performed using Principal Component Analysis (PCA) and Positive Matrix Factorization (PMF). Carbonaceous components, water-soluble inorganic compounds, and trace elements were analyzed from PM (TSP, PM10, and PM2.5) samples. The measured PM2.5 and PM10 concentrations were 5 to 10 times and 3 to 8 times higher than the 2005 WHO 24-hour standards, respectively. PCA and PMF analyses identify five sources in both cities. The sources contributing to aerosol concentrations (PM2.5 - PM10) in Bamako are motor vehicles (20-13%), solid fuel combustion (16-13%), crustal dust (24-30%), resuspended road dust (26-30%) and secondary aerosols (10-16%). During the sampling period in Bamako, dust was the most prevalent source, accounting for 63% of the total PM10 mass. In Dakar, the main identified sources were motor vehicles (28-19%), mineral dust (16-25%), industries and oil burn-ing (11-10%), sea salts (15-20%), and resuspended road particles (21-29%). The findings also indicate that anthropogenic emissions contribute significantly to the PM2.5 fraction, implying that populations are highly exposed to fine particles.

Falls, highly common in the constantly increasing global aging population, can have a variety of negative effects on their health, well-being, and quality of life, including restricting their capabilities to conduct Activities of Daily Living (ADLs), which are crucial for one’s sustenance. Timely assistance during falls is highly necessary, which involves tracking the indoor location of the elderly during their diverse navigational patterns associated with ADLs to detect the precise location of a fall. With the decreasing caregiver population on a global scale, it is important that the future of intelligent living environments can detect falls during ADL.s while being able to track the indoor location of the elderly in the real world. Prior works in these fields have several limitations, such as – the lack of functionalities to detect both falls and indoor locations, high cost of implementation, complicated design, the requirement of multiple hardware components for deployment, and the necessity to develop new hardware for implementation, which make the wide-scale deployment of such technologies challenging. To address these challenges, this work proposes a cost-effective and simplistic design paradigm for an Ambient Assisted Living system that can capture multimodal components of user behaviors during ADLs that are necessary for performing fall detection and indoor localization in a simultaneous manner in the real world. Proof of concept results from real-world experiments are presented to uphold the effective working of the system. The findings from two comparison studies with prior works in this field are also presented to uphold the novelty of this work. The first comparison study shows how the proposed system outperforms prior works in the areas of indoor localization and fall detection in terms of the effectiveness of its software design and hardware design. The second comparison study shows that the cost for the development of this system is the least as compared to prior works in these fields, which involved real-world development of the underlining systems, thereby upholding its cost-effective nature.

: During the period of COVID-19, the Chinese government implemented a series of actions to prevent the spread of the virus. It is noticed that these preventive actions have generated positive effects on air pollution in Wuhan and Beijing. And, due to the differences in city functions, geographic locations, meteorological conditions, and preventive action details between the two cities, noticeable difference is observed on how they reduced air pollution. This unfortunate incident has become a social sample for studying the industrial and livelihood activities impact on air pollution, otherwise would be highly impossible. This paper starts from observing data from NASA's real-time fine particulate matter (PM2.5) and NO2, and comparing the air pollution in this special time domain with previous years. It is discovered that both PM2.5 and NO2 have been reduced in Wuhan, while only NO2 has significant reduction in Beijing, during the COVID-19 responses. This suggests that the human activity suppression by the COVID-19 control yields different effects on different pollutants and in different cities. Possible reasons for such effects are analysed by considering the public health control levels as well as the pollutant migration, industrial activities, and the weather conditions.

This work investigates spatial and temporal distributions of hydroxyl, OH, in laser-plasma in laboratory air at standard ambient temperature and pressure. Of interest are determination of temperature and density of OH and establishment of a correlation of molecular OH emission spectra with shadow graphs for time delays of 50 to 100 microsecond, analogous to previous work on shadow graph and emission spectroscopy correlation for cynaide, CN, in gas mixtures and for time delays of the order of 1 microsecond. Wavelength- and sensitivity- corrected spatiotemporal data analysis focuses on temperature inferences using molecular OH emission spectroscopy. Near-ir radiation from a Q-switched laser device initiates optical breakdown in laboratory air. The laser device provides 6 nanosecond, up to 850 milli Joule pulses at a wavelength of 1064 nanometer, and focal irradiance in the range of 1 to 10 Tera Watt per centimeter-squared. Frequency doubled beams are utilized for capturing shadow graphs for visualization of the breakdown kernel at time delays in the range of 0.1 to 100 microsecond. OH emission spectra of the laser plasma, spatially resolved along the slit dimension, are recorded in the wavelength range of 298 nm to 321 nm, and with gate widths adjusted to 10 microsecond for the intensified charge-coupled device that is mounted at the exit plane of a 0.64 m Czerny-Turner configuration spectrometer. Diatomic OH signals occur due to recombination of the plasma and are clearly distinguishable for time delays larger than 50 microsecond, but are masked by spectra of N2 early in the plasma decay.

We describe a novel machine that uses the greater-than-100% efficiency of air/ground-source heat pumps to recursively generate electricity via steam-powered generators, taking thermal energy from the ambient environment to convert into electrical power. The invention of a machines that generate clean power at low costs will be fundamental to the future of electricity. We estimate efficiency and calculate minimum efficiencies for unknown parts to consider the applicability of this machine to the real world.

Growing popularity of buildings with integrated sub-systems, requires a review of methods to optimize the preheat of ventilation air. An integrated system permits using geothermal heat storage parallel to the direct outdoor air intake with additional treatment in the mechanical room as a part of building automatic control system. Earth Air Heat Exchanger (EAHX) has many advantages but also has many unanswered questions. Some of the drawbacks are: a possible entry of radon gas, high humidity in the shoulder seasons as well as the need for two different air intake sources with a choice that depends on the actual weather conditions. While in winter, the EAHX may be used continuously to ensure thermal comfort, in other seasons, its operation must be automatically controlled. To generate the missing information about the EAHX technology we have examined two nearly identical EAHX systems, one placed in ground next to the building and the other under the basement slab. In another project, we have reinforced the ground storage action by heat exchanger placed on the return pipes of the hydronic heating system. Effectively, the information provided in this paper, shows advantages of merging both these approaches while the EAHX could be placed under the house or near the basement foundation that is using an exterior basement insulation.

Growing popularity of smart and integrated buildings requires a review of methods to optimize the preheat of ventilation air. An integrated system permits using heat ex-changers located in the mechanical room or in the future even using an exterior wall as a heat exchanger. One may ask the question how does the earth-air heat exchanger (EAHX) technology fitts into this function. EAHX has many advantages but also has many unanswered questions. Some of the drawbacks are: a possible entry of radon gas, high humidity in the shoulder seasons as well as the need for two different air intake sources with a choice that depends on the actual weather conditions. While in winter, the EAHX may be used continuously to ensure thermal comfort, in other seasons, its operation must be automatically controlled. To generate the missing information about the EAHX technology we reviewed literature and examined two nearly identical EAHX systems, placed either in ground next to the building or under the basement slab. Effectively, the information provided in this paper, shows advantages of merging both these approaches while the EAHX shoud be placed under the house or near the basement foundation.

Abstract: The air pollution dispersion modelling via spatial analyses (Land Use Regression – LUR) is an alternative approach to the air quality assessment to the standard air pollution dispersion modelling techniques. Its advantages are mainly much simpler mathematical apparatus, quicker and simpler calculations and a possibility to incorporate other factors affecting pollutant’s concentration. The goal of the study was to model the PM10 particles dispersion modelling via spatial analyses v in Czech-Polish border area of Upper Silesian industrial agglomeration and compare results with results of the standard Gaussian dispersion model SYMOS’97. Results show that standard Gaussian model with the same data as the LUR model gives better results (determination coefficient 71% for Gaussian model to 48% for LUR model). When factors of the land cover and were included into the LUR model, the LUR model results were significantly improved (65% determination coefficient) to the level comparable with Gaussian model. The hybrid approach combining the Gaussian model with the LUR gives superior quality of results (65% determination coefficient).

Recently Kawashima has reported that, when wetted with alkanes, several forms of graphite and single-layer graphene exhibit superconductor-like properties above room temperature under ambient pressure [AIP Adv. 2013, 3, 052132; arXiv:1612.05294; arXiv:1801.09376]. Under the assumption that these seemingly unlikely properties arise from the presence of paired electrons brought about by the alkane-wetting, we explored their implications to arrive at a probable mechanism for strong electron-pairing driven by Fermi surface nesting and acoustic phonon. This mechanism explains why alkane-wetting is essential for the graphene systems to become “superconductor-like” above room temperature and why the “T_c” of alkane-wetted pitch-based graphite fibers increases almost linearly from ~363 to ~504 K with increasing the molecular weight of alkane from heptane to hexadecane. It also provides a number of experimentally-verifiable predictions, the confirmation of which will provide a strong support for the superconductivity driven by Fermi surface nesting and acoustic phonon.

Air pollution knows no boundaries, which means for a city or a region to attain clean air standards, must not only look at the emission sources within its own administrative boundary, but also at sources in the immediate vicinity and those originating from long-range transport. And there is a limit to how much area can be explored to evaluate, govern, and manage as designated airsheds for cities and larger regions. This paper discusses the need from an official airshed framework for India’s air quality management, urban airsheds designated for India’s 131 non-attainment cities under the national clean air programme, and proposes climatically and geographically appropriate regional airsheds to support long-term planning. Between 28 states, eight union territories, 36 meteorological sub-regional divisions, and six regional meteorological departments, establishing the proposed 15 regional airsheds for integrated and collaborative air quality management across India is a unique opportunity.

The educational and play-related activities of children are proceeded mainly indoors in a kin-dergarten. The exposure of children to high concentrations of PM2.5 and CO2 indoors have leaded to various harmful effects and negatively impact educational outcomes in a kindergarten. Therefore, this study presents a numerical model of CO2 and PM2.5 concentration based on two classrooms in a kindergarten. Using this numerical model, we present different scenarios of oper-ating mechanical ventilation and air purifiers in kindergartens with the aim of optimizing for reducing the concentrations of CO2 and PM2.5. We found that the amount of ventilation required to maintain good air quality, per child, was approximately 20.4 m3/h. However, we also found that as the amount of ventilation increased, so did the concentration of indoor PM2.5; we found that this issue can be resolved through the use of a high-grade filter (i.e., a MERV 13 grade filter with a collection efficiency of 75%). This study provides a scientific basis for reducing PM2.5concentrations in kindergartens, while keeping CO2 levels low.

This study proposes an image recognition method to assist swine farm managers in collecting health data related to pig feeding and excretion. Analyzing the correlation between sow health data and indoor air quality in the pigsties revealed significant influences of air quality indicators on sow health. Increased levels of TVOC, CO2, and temperature were found to negatively affect feeding health, while increased temperature, humidity, and PM10 were found to negatively impact excretion health. These findings provide a basis for evaluating variables when constructing future sow disease prediction models. Analyzing the correlation between pig health status and air quality can help swine farm managers improve sow production environments, reduce disease risks, enhance production efficiency, and provide valuable insights for future research on disease prediction models.

Multiple social and environmental justice concerns are linked to urban form such as the distribution of socioeconomic class populations, healthcare spending, air pollution exposure, and human mobility. This study used 1m resolved LIDAR data to characterize land use in Salt Lake County, Utah and associate it with sociodemographic and air quality data at the census block group and zip code levels. We found that increasing tree cover was associated with higher per capita income and lower minority populations while increasing built cover was linked to lower per capita income and higher minority populations. Air quality showed less strong correlations, however, decreased non irrigated cover, increased built cover, and higher amounts of households living under poverty was related to higher long-term PM2.5 exposure. Several policy efforts have been undertaken to improve air quality and reduce negative health outcomes in Utah which are being informed by regulatory and research grade air quality sensors.

Most people living in Europe's cities are still exposed to levels of air pollution deemed harmful by the World Health Organization. In the modern world, air pollution is the foremost concern because of its impact in human health and economy. This strong connection appears gaining a lot of concern, driven by new installed low-cost electrochemical sensors monitoring systems. Highly accuracy, real-time monitoring, daily and yearly statistics, data access from experts or simple users, low-cost equipment and forecasting needs, enforce the market to develop new air quality monitoring systems using advanced technologies and protocols. In this study, a comparison via low-cost electrochemical sensors and of static, fixed site measurement monitoring station, is taking place in Athens, Greece, along with the data quality and Air Quality Index (AQI) including data accuracy and quality of data concerning adverse health effects due to air pollution. The findings presented in this work, relate to different flexible and affordable alternatives adopted during the evaluation and calibration of low-cost gas sensors for the monitoring. The significance of the positive results is particularly useful, especially considering the founding for interference, environmental conditions affections and air quality information including indexes and health recommendations for a specific location.

Silicone rubber formulations in the form of thin discs have been studied under room ambient conditions for their surface characteristics. The samples were silicone rubber manufactured in laboratory and those industrially manufactured. The measurements were done using an electrometer high resistance meter, applying dc voltage under normal room ambient conditions. The results show that the silicone rubber samples show higher values of surface resistivity when the dc voltage was applied. Silicone rubber samples manufactured in laboratory seem to exhibit erratic behaviour unlike their corresponding silicone rubbers manufactured in industry; this could be due to manufacturing shortcomings in laboratory and the irregularities in the way the silicone rubber adhered to the concentric ring electrodes. The empirical current traversing the surface of the silicone rubbers does not decay exponentially but rather it decays as an exponential power of the energization time.

Air pollution has been a major environmental issue worldwide from the last few decades. It is a man-made issue that has a serious harmful impact on the environment and the health of humans. There are different sources of emission, but industrial processes and motor vehicles contribute to a chief part of air pollution. It has acute as well as chronic effects on the health of humans and affects different organs. It is thought the main environmental risk factor in the incidence and progression of several diseases such as lung cancer, asthma, Alzheimer's and Parkinson's diseases. Long-term exposure to air pollution has different toxicological impacts on humans such as respiratory and cardiovascular diseases, neuropsychiatric complications, eye irritation and skin diseases. As per the study by the World Health Organization (WHO), nitrogen oxides (NOx), carbon monoxide (CO), ozone (O₃), sulfur dioxide (SO₂), volatile organic compounds (VOCs) and heavy metals are the major air contaminants. These pollutants are different in their properties, composition and time of disintegration. The aim of this study is to review the different sources, types, impacts, challenges and mitigation of air pollution in detail.