Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

Temperature is a critical factor that influences the proliferation of pathogens in hosts. The impact of temperature on pathogens is commonly explored in controlled and constant temperatures. Experiments under varying environmental temperature are becoming more frequent, however, testing every temperature scenario à la carte is unachievable. One example of this is the human pathogen Vibrio parahaemolyticus (Vp) in oysters. Here, a predictive model was developed for predicting the growth of Vp in oysters under varying ambient temperature. The model was fitted and evaluated against data from experiments studying growth and inactivation of Vp in oysters at eight constant temperatures. Once evaluated, Vp dynamics in oysters were estimated at different post-harvest varying temperature scenarios affected by water and air temperature, and different ice treatment timing. The model performed adequately under varying temperature, reflecting that (i) increasing temperature, particularly in hot summers, favors a rapid Vp growth in oysters, resulting in a very high risk of gastroenteritis in humans after consumption of a serving of raw oysters, (ii) pathogen inactivation due to day/night oscillations, and more evidently, due to ice treatments, (iii) ice treatment is much more effective limiting risk of illness when applied immediately onboard compared to dockside. The model results to be a promising tool for improving the understanding of the Vp-oyster system and support studies on public health impact of pathogenic Vp associated with raw oyster consumption. Although robust validation of the model predictions is needed, initial results and evaluation show the potential of the model to be easily modified to match similar systems where the temperature is a critical factor shaping the proliferation of pathogens in hosts.

The impact of cyclic heat stress (CHS) and lighting events on pig feeding behavior (FB) was investigated. The FB of 90 gilts was recorded in real time under two ambient temperatures (AT): thermoneutrality (TN, 22 °C) or CHS (22°/35 °C). The day was divided into four periods: PI (06-08 h); PII (08-18 h); PIII (18-20 h); and PIV (20-06 h). Automatic and Intelligent Precision Feeders recorded each feed event for each pig. An estimated meal criterion (49 minutes) was used to calculate the FB variables. Feed behavior in both ATs followed a circadian pattern. The CHS reduced the feed intake by 6.9%. Pigs prioritized feed intake during the coolest hours of the day; however, nocturnal cooling did not allow the pigs to compensate for the reduced meal size due to CHS. The highest meal size and most of the meals were observed during the lighting-on period. Pigs reduced their interval between meals during periods II and III. The lighting program increased the meal size when the lights were switched on and reduced the meal size when the lights were switched off. Thus, the dynamics of the FB were largely influenced by AT, while the meal size was affected by the lighting program.

In CCS projects, the transportation of CO₂ by ship can be an attractive alternative to transportation using a pipeline, particularly when the distance between source and disposal location is large. However, the energy consumption of the liquefaction process can be significant, making the selection of an energy-efficient design an important factor in the minimization of operating costs. Since the liquefaction process operates at low temperature, its energy consumption will vary with ambient temperature, which could be a factor that influences the trade-off point between pipelines and shipping in different geographic locations. A consistent set of data showing the relationship between energy consumption and cooling temperature is therefore potentially useful to CCS system modelling. This study compares the performance of a wide range of CO₂ liquefaction schemes. It applies a methodical approach to the optimization of process operating parameters and studies performance across a range of operating temperatures. A set of data for the minimum energy consumption cases is presented. The main findings are that open-cycle CO₂ processes often offer minimum energy consumption; NH₃ based schemes often offer better performance at higher ambient temperatures; and that for the cooling temperature range 15 to 50 °C, the energy consumption for the best performing liquefaction process rises by around 40%.

Abstract: Metal-air batteries provide a most promising battery technology given their outstanding potential energy densities, which are desirable for both stationary and mobile applications in a ‘beyond lithium-ion’ battery market. Silicon- and iron-air batteries underwent less research and development compared to lithium- and zinc-air batteries. Nevertheless, in the recent past, the two also-ran battery systems made considerable progress and attracted rising research interest due to the excellent resource-efficiency of silicon and iron. Silicon and iron are among the top five of the most abundant elements in the earth’s crust, which ensures almost infinite material supply of the anode materials, even for large scale applications. Furthermore, primary silicon-air batteries are set to provide one of the highest energy densities among all batteries, while iron-air batteries are frequently considered as a highly rechargeable system with decent performance characteristics. Considering fundamental aspects for the anode materials, i.e., the metal electrodes, in this review, we will first outline the challenges, which explicitly apply to silicon- and iron-air batteries and prevented them from a broad implementation so far. Afterwards, we provide an extensive literature survey regarding state-of-the-art experimental approaches, which are set to resolve the aforementioned challenges and might enable the introduction of silicon- and iron-air batteries into the battery market in the future.

Grazing incidence X-Ray Diffraction spectroscopy was employed to characterize crystallinity of Iron, Nickel, Copper and Tungsten, prepared by sparking discharge process in presence of 0.4 T magnetic field at ambient temperature 25 °C. Iron thin film preserved crystallinity even after one year of ageing. Nickel exhibit higher crystallinity when sparked in nitrogen gas flow from the one sparked in oxygen. Tungsten was successfully crystalized after just 40 minutes of sparking inside of magnetic field.

The Human immunodeficiency virus-1 (HIV-1) matrix (MA) domain is involved in the highly regulated assembly process of the virus particles that occur at the host cell’s plasma membrane. High-resolution structures of the MA domain determined using cryo X-ray crystallography have provided initial insights into the possible steps in the viral assembly process. However, these structural studies have relied on large and frozen crystals in order to reduce radiation damage caused by the intense X-rays. Here, we report the first XFEL study of the HIV-1 MA domain’s interaction with inositol hexaphosphate (IP6), a phospholipid headgroup mimic. We also describe the purification, characterization and microcrystallization of two MA crystal forms obtained in the presence of IP6. In addition, we describe the capabilities of serial femtosecond X-ray crystallography (SFX) using X-ray free-electron laser (XFEL) to elucidate the diffraction data of MA-IP6 complex microcrystals in liquid suspension at ambient temperature. Two different microcrystal forms of MA-IP6 complex both diffracted to beyond 3.5 Å resolution, demonstrating the feasibility of using SFX to study the complexes of MA domain of HIV-1 Gag polyprotein with IP6 at near-physiological temperatures. Further optimization of the experimental and data analysis procedures will lead to better understanding of the MA domain of HIV-1 Gag and IP6 interaction at high resolution and provide basis for optimization of the lead compounds for efficient inhibition of the Gag protein recruitment to the plasma membrane prior to virion formation.

Worldwide emission standards are now required to cover engine operation under extreme ambient conditions, which affect the raw emissions and the efficiency of the exhaust aftertreatment systems. These regulations also target new combustion technologies for decarbonization, such as neat hydrogen (H2) combustion or dual-fuel strategies, which involve a challenge to the analysis of exhaust aftertreatment systems requirements and performance. This work addresses the impact of high altitude and low ambient temperature conditions on the reactivity of an oxidation catalyst in the presence of H2. A reaction mechanism is proposed to cover the main conversion paths of CO, HC, and H2, including the formation and consumption of high-energy surface reaction intermediates. The mechanism has been implemented into a faster-than-real-time reduced-order model for multi-layer washcoat honeycomb catalytic converters. The model was utilized to investigate the effect of H2 concentration on the reactivity of CO and HC within the catalyst under various operating and ambient conditions. By applying the model and examining the selectivity towards different reaction pathways in the presence H2, insights into surface intermediates and reactivity across different cross-sections of the monolith were obtained. This analysis discusses the underlying causes of reactivity changes promoted by H2 and its relative importance as a function of driving boundary conditions.

Hydrogen used as an energy carrier can provide an important route to the decarbonization of energy supplies. However, realizing this opportunity requires a significant increase in both production and transportation capacity. Part of the increase in transportation capacity could be provided by the shipping of liquid hydrogen, but this introduces an energy-intensive liquefaction step into the supply-chain. The energy required for liquefaction can be reduced by developing improved process designs, but since all low-temperature processes are affected by the available heat-sink temperature, local ambient conditions will also affect the energy penalty. This work studies how the energy consumption associated with liquefaction varies with heat-sink temperature through the optimization of design parameters for a typical next-generation hydrogen liquefaction process. The results show that energy consumption increases by around 20%, across the cooling temperature range 5 to 50 °C. Considering just the range 20 to 30 °C there is a 5% increase, illustrating the significant impact ambient temperature can have on energy consumption.

Recently Kawashima has reported that, when wetted with alkanes, several forms of graphite and single-layer graphene exhibit superconductor-like properties above room temperature under ambient pressure [AIP Adv. 2013, 3, 052132; arXiv:1612.05294; arXiv:1801.09376]. Under the assumption that these seemingly unlikely properties arise from the presence of paired electrons brought about by the alkane-wetting, we explored their implications to arrive at a probable mechanism for strong electron-pairing driven by Fermi surface nesting and acoustic phonon. This mechanism explains why alkane-wetting is essential for the graphene systems to become “superconductor-like” above room temperature and why the “T_c” of alkane-wetted pitch-based graphite fibers increases almost linearly from ~363 to ~504 K with increasing the molecular weight of alkane from heptane to hexadecane. It also provides a number of experimentally-verifiable predictions, the confirmation of which will provide a strong support for the superconductivity driven by Fermi surface nesting and acoustic phonon.

As of now, anthropogenic habitat injury via dissemination of manufactured chemicals is injuring the world’s ecosystems, but doctors have yet to recognize its consequences to humans. Recognition of overt toxicity due to chronic low-dose exposure will open the door to diagnosis, sequential elimination studies, and prescriptions for preventive cure that represent a first step in preventing escalating chronic diseases. This paper offers a diagnostic construct for such use: chronic ambient poisoning. Incorporating it into clinical practice can reduce misdiagnosis of gastro- and near-toxicity that doctors and patients presently suppress rather than remove, and reduce patient co-dependence with proton-pump inhibitors, anxiolytics, and antidepressants—and the thriving “alternative” health industry. This diagnostic elephant-in-the-room is presently missed for reasons of habit (when an ailment is not recognized, it cannot be included in the differential diagnosis) and of poor conduct and interpretation of non-clinical research studies that are taken to mean an absence of evidence is evidence of absence. Moreover, modern methods fail when: the exposure comprises a “daily cocktail” of poisons acting additively, interactively, and cumulatively over a lifetime; when there is no normal, unexposed comparison group; and when absence of a robust etiopathogenetic model disallows inapt statistics. Only patient-led, consultant-informed sequential elimination studies can “peel the onion” of toxicity and its recognition and “preventive cure”. Clinical use of the chronic ambient poisoning diagnosis can thus open the door to stemming and reversing anthropogenic epidemics.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

Natural gas combined cycle power plants (CCPPs) are widely used to meet peak loads in electric energy production. Continuous monitoring of the output electrical power of CCPPs is a requirement for power performance. In this study, the role of ambient temperature change having the greatest effect on electric production is investigated for a natural gas CCPP. The plant has generated electricity for fourteen years and setup at 240 MW in Aliağa, İzmir, Turkey. Depending on the seasonal temperature changes, the study data were obtained from each gas turbine (GT), steam turbine (ST) and combined cycle blocks (CCBs) in the ambient temperature range of 8-23°C. It has been found that decreases of the electric energy in the GTs because of the temperature increase and indirectly diminishes of the electricity production in the STs. As a result, the efficiency of each GT, ST and CCB reduced, although the quantity of fuel consumed by the controllers in the plant was decreased. As a result of this data, it has been recommended and applied that additional precautions have been taken for the power plant to bring the air entering the combustion chamber to ideal conditions and necessary air cooling systems have been installed.

The purpose of this study is to assess the concentration-response relations between conjunctivitis and exposure to ambient ozone. This retrospective study includes emergency department (ED) visits for conjunctivitis in Edmonton, Canada, for the period April 1992–March 2002. Daily average levels of ozone (range: 1.2–50.9, ppb), of temperature, and of relative humidity were estimated and used for the period of the study. For each of the considered exposure lags, (from 0 to 9 days), six different models were fitted to estimate the concentration-response function. The goodness of fit was assessed using the Akaike information criterion. During the period of the study, 17,211 ED visits for conjunctivitis were recorded and used. For all subjects together, a positive statistically significant association was obtained for the exposure lagged by 5 days. For female subjects, lags 1, 3, and 9 had positive statistically significant associations (lag 2 had negative associations). For male subjects, only lag 5 had a positive statistically significant association. The estimated non-linear concentration-response functions for the considered groups (all, males, females) and lags, revealed the associations along the exposure levels. The fitted shapes are described by algebraic functions and may have various forms. The estimated functions are useful to determine the risk associated with exposure to ground-level ozone.

Negative temperature coefficient (NTC) materials are usually based on ceramic semiconductors and electrons are involved in their transport mechanism. A new type of NTC material, adequate for alternating current (AC) applications, is represented by zeolites. Indeed, zeolites are single-charge carrier ionic conductors with a temperature-dependent electrical conductivity. In particular, electrical transport in zeolites is due to the monovalent charge-balancing cations, like K⁺, capable of hopping between negatively charged sites in the aluminosilicate framework. Owing to the highly non-linear electrical behavior of the traditional electronic NTC materials, the possibility to have alternative types of materials, showing linearity in the electrical behavior, is very desirable. Among different zeolites, the natural clinoptilolite has been selected for investigating the NTC behavior since it is characterized by high zeolite content, convenient Si/Al atomic ratio, good mechanical strength, due to its compact microstructure, and low toxicity. Clinoptilolite has shown a rapid and quite reversible impedance change under heating, characterized by a linear dependence on temperature. X-ray diffraction (XRD) has been used to identify the natural zeolite, to establish all types of crystalline phases present in the mineral, and to investigate the thermal stability of these phases up to 150°C. X-ray photoelectron spectroscopy (XPS) analysis has been used for the chemical characterization of the natural clinoptilolite sample, providing important information on the cationic content and framework composition. In addition, since electrical transport takes place in the zeolite free-volume, a Brunauer–Emmett–Teller (BET) analysis of the mineral has been also performed.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

A proposed low-temperature forging method aims to enhance stainless steel bearings by creating a martensitic subsurface layer, significantly boosting bearing fatigue life due to increased surface hardness. This technique induces beneficial residual stresses, particularly in axial bearings, streamlining their construction and improving machine elements. Challenges persist, especially with radial bearings, but simplicity in axial bearing forging promotes compact, resource-efficient facility construction. Future research will focus on applying this technique to axial bearing washers, potentially replicating success in other bearing components. Despite the energy ex-penditure for cooling during forging, the substantial increase in bearing fatigue life offsets this, enhancing overall longevity and reliability of critical machine components. Integration of this forging technique into bearing fabrication appears seamless, offering a promising trade-off be-tween energy use and enhanced performance.

Ecuador is an important center of biodiversity of the plant family Amaryllidaceae, specially the subfamily Amaryllidoideae, known as a source of important bioactive molecules. The aim of this study was to assess the chemical and biological potential of four different species of Amaryllidoideae collected in Ecuador: Urceolina formosa, Urceolina ruthiana, Clinanthus incarnatus, and Stenomesson aurantiacum. Sixteen alkaloids were identified in the bulb extract of these species by GC-MS, which the extract of S. aurantiacum exhibiting the greatest structural diversity. The potential of these three genera against Alzheimer’s disease was evaluated by measuring their AChE and BuChE inhibitory activity, revealing that C. incarnatus and U. formosa (from Sucumbíos province) showed the best results with IC50 values of 1.73 ± 0.25 and 30.56 ± 1.56 g·ml-1, respectively. Molecular dynamic assays were conducted to elucidate the possible interactions that occurs among 2-hydroxyanhydrolycorine and AChE enzyme, suggesting some similarity with those observed for galanthamine. This study enhances our understanding of the biodiversity of Amaryllidoideae species from Ecuador, highlighting their potential as a source of chemical compounds with pharmaceutical potential.

Cities exemplify the evolving world with changing demographics and climates. Urban green spaces play a crucial role in improving the quality of life of people through their potential to mitigate temperatures. Therefore, comprehending their impact is of para-mount interest. Given the challenges in obtaining temperature data from urban locations, this study develops Artificial Neural Networks (ANNs) to predict daily and hourly temperatures in Valladolid, Spain, with a particular focus on urban allotment gardens and a forested urban park. ANNs were built and evaluated from various combinations of inputs (X), hidden neurons (Y) and outputs (Z) under the practical rule of "making net-works simple, to obtain better results". The best performing model was 6-Y-1 ANN archi-tecture with an impressive result of Root Mean Square Error (RMSE) = 0.42°C in the urban garden called Valle de Arán. However, other five ANN architectures were also tested (7-Y-5; 6-Y-5; 7-Y-1; 3-Y-Z and 2-Y-1). ANNs dedicated to urban temperature analysis hold immense potential for urban planning and research, aiding in under-standing the urban climate, forecasting future temperatures, identifying temperature mitigation strategies and even for managing urban crops

Nanoparticles (NP), Nanoaerosols (NA), ultrafine particles (UFP), and PM0.1 (particles with a diameter ≤ 0.1 µm or 100 nm) are interchangeably used in the field of atmospheric studies. PM0.1 are emitted from both natural and anthropogenic sources. The main emission sources of PM0.1 are combustion processes, including biomass and fossil fuel. Moreover, secondary formation via atmospheric photochemical reactions can also occur depending on meteorological conditions and the suspended pollutant species. Identifying the physical and chemical characteristics and spatial and temporal variations is vital in terms of understanding the effect of NPs on the environment, the global climate, and human health risks. This review article summarizes recent research on PM0.1 in Thailand. The review involves peer-reviewed papers from Scopus and the Web of Science databases, and includes the most recently published articles in the past ten years (2013-2022). UFPs mainly come from the combustion processes such as motor vehicles. The high mass concentration of PM0.1 that occurs during the dry season in which open fires depend on the specific region of Thailand. Particulate pollution from local and cross-border countries also needs to be considered in terms of the concentrations of ambient nanoparticles. The overall conclusions reached will likely have a beneficial long-term impact on achieving a blue sky over Thailand through the development of coherent policies and managing new air pollution challenges and sharing knowledge with a broader audience.

The static formation temperature (SFT) is required to determine the thermophysical properties and production parameters in geothermal and oil reservoirs. However, the SFT is not easy to be obtained by both experimental and physical methods. In this paper, a mathematical approach to predicting SFT based on a new model describing the relationship between bottom hole temperature (BHT) and shut-in time was proposed. The unknown coefficients of the model were derived from least squares fit by Particle Swarm Optimization (PSO) algorithm. Besides, the ability to predict SFT based on a few BHT data (such as first 3, 4, or 5 ones of a data set) was evaluated. The accuracy of the proposed method to predict SFT was testified with a deviation percentage less than ±4% and high values of regression coefficient R² (>0.98). The proposed method could be used as a practical tool to predict SFT in both geothermal and oil wells.

A revised reversed Carnot cycle without external heat source and temperature gap is proposed to challenge the classic reversed Carnot cycle, heat pumps based on the proposed cycle with super energy efficiency works just like electric heater fitted for any climate including extreme cold weather, the application of these new heat pumps is discussed with conclusion that little real obstacles exist for scale application to address the heating related climate change, also a demonstration case shows a remarkable results to encourage the applications of these new heat pumps.

Heavy rains have created significant threats to human health and life. Floods and other natural disasters, which have a global impact annually, can be attributed to extended durations of intense precipitation. Accurate rainfall predictions are crucial in nations such as Bangladesh, where agriculture is the predominant occupation. The efficiency of machine learning (ML) methods is enhanced by the non-linearity of rainfall, surpassing the effectiveness of other alternative ways. Machine learning techniques show that individual classifiers exhibit worse accuracy than ensemble learning (EL) methodologies. Ensemble Learning techniques are utilized for rainfall prediction and estimating rainfall quantity and daily average temperature to enhance comprehension of the diverse Machine Learning algorithms. This research implements the machine learning techniques and ensemble-based classifier to predict the rainfall occurrence, along with the machine learning regressor models and ensemble-based regressor for the rainfall amount prediction and daily average temperature prediction, using Bangladesh Weather Dataset. The results of the machine learning and ensemble-based models are compared using the Accuracy and F1 score for rainfall occurrence prediction. In contrast, MAE and RMSE evaluation metrics are used for ensemble regressor and regression algorithms for the rainfall amount and daily average temperature prediction. With an accuracy of 83.41% and a recall of 78.17%, the Ensemble Classifier is the best at predicting when it will rain, but its precision of 51.16% stands in for the lowest. The Ensemble Regression model outperforms Linear Regression, Random Forest, and SVR in rainfall amount prediction, with the lowest MAE of 0.36 and RMSE of 0.90. The Ensemble Regression provides the most precise results for daily average temperature prediction with the lowest MAE 0.42 and RMSE 0.54 highlighting its superiority over the other regression models in forecasting temperature with less error. Ensemble approaches consistently lead task performance metrics.

Long term Precipitation and temperature variations are one of the main determinants of climate variability of one’s area. The aim of this study is to determine trends variation in climatic elements of temperature and precipitation in the southern zone of Tigray regional state, Ethiopia. The station is assumed for the study of climatic records over southern zone of the region in detection for probable trends. The daily, monthly and annual precipitation totals and temperature observed at korem meteorological station were used for the period of 1981-2010 for Precipitation and 1985 – 2010 for minimum and maximum temperature. Summary of descriptive statistics and Mann Kendall test methods were employed for the observed data analysis to demonstrate any existence of possible trends. The main findings of the study indicated that the mean and maximum temperature had a general increasing trend; however, minimum temperature showed decreasing trend. In general annual temperature from 1985 – 2010 of the area showed a warming trend. Moreover analysis of the 30 years (1981-2010) annual precipitation showed a coefficient of variation ranging from 33.77 – 233 %. It indicated that the precipitation dissemination is not normal with large year to year variances.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

Ethylene Oxide (EtO) is a colorless, flammable gas at room temperature, produced by the catalytic oxidation of ethylene. EtO is widely used by medical sterilization facilities to clean medical supplies and equipment. Recent epidemiological studies showed that EtO is a more potent carcinogen than previously documented, leading the Environmental Protection Agency (EPA) to update, in December 2016, the inhalation unit risk estimate for EtO. This resulted in the identification of EtO as a potential health concern in several areas across the US, including the state of Utah. The geography surrounding Salt Lake Valley creates a bowl; ideal for collecting air pollution emissions. The region often experiences inversion episodes which inhibit vertical mixing and cause an accumulation of air pollutants, leading to unhealthy pollution levels. Using the EPA's dispersion modeling software, AERMOD, this study estimated EtO concentrations through facility stack and fugitive emissions modeling results. These values were compared with those of canister-based concentrations from ambient air samples taken near a medical device sterilization facility in the Salt Lake Valley. Stainless steel, whole-air passivated canisters were used to collect 24-hour ambient concentration samples of EtO. Eight locations surrounding a Salt Lake Valley medical device sterilization facility and four background sites were chosen to measure the ambient concentrations. Accounting for potential atmospheric impacts on EtO, measurements were sampled in winter 2022 (January-March) and summer 2022 (July-September). The modeled EtO concentrations were adjusted to account for background values associated with the winter or summer data. Then the two methodologies were compared using a Wilcoxon Sign-ranked, paired test. The statistical analysis resulted in six of the eight sample locations surrounding the sterilization facility being significantly different when comparing canister-based measurements of ambient EtO to modeled estimates. Canister-based measurements taken at sites one, three, and four were statistically greater than the modeled estimates, while sites two, five, and seven were statistically less than the modeled estimates. Also, the summer background value calculated was almost 2.5 times greater than the winter. The results do not suggest whether one method is more or less conservative than the other. In conclusion, the five of the closest sites and site seven were statistically different when comparing measured and modeled ambient concentrations of EtO. The comparison results do not clearly indicate if a correction factor could be derived for future human exposure to cancer risk assessment modeling. However, it is reasonable that the closer to the sterilization facility, the more total EtO exposure will be realized.

The non-contact patient monitoring paradigm moves patient care into their homes and enables long-term patient studies. The challenge, however, is to make the system non-intrusive, privacy-preserving, and low-cost. To this end, we describe an open-source edge computing and ambient data capture system, developed using low-cost and readily available hardware. We describe five applications of our ambient data capture system. Namely: (a) Estimating occupancy and human activity phenotyping; (b) Medical equipment alarm classification; (c) Geolocation of humans in a built environment; (d) Ambient light logging; and (e) Ambient temperature and humidity logging. We obtained an accuracy of 94% for estimating occupancy from video. We stress-tested the alarm note classification in the absence and presence of speech and obtained micro averaged F1 scores of 0.98 and 0.93, respectively. The geolocation tracking provided a room-level accuracy of 98.7%. The root mean square error in the temperature sensor validation task was 0.3°C and for the humidity sensor, it was 1% Relative Humidity. The low-cost edge computing system presented here demonstrated the ability to capture and analyze a wide range of activities in a privacy-preserving manner in clinical and home environments and is able to provide key insights into the healthcare practices and patient behaviors.

Abstract: Mass spectrometry research laboratories reported multiple probes for ambient ionization in the last years. Combining them with a mechanical moving stage enables automated sampling and imaging applications. We developed a robotic platform, which is based on RepRap 3D-printer components, and therefore easy to reproduce and to adopt for custom prototypes. The minimal step width of the Open LabBot is 12.5 μm, and the sampling dimensions (x, y, z) are 18 × 15 × 20 cm. Adjustable rails in an aluminium frame construction facilitate the mounting of additional parts such as sensors, probes, or optical components. The Open LabBot uses industry-standard G-code for its control. The simple syntax facilitates the programming of the movement. We developed two programs: 1) LABI-Imaging, for direct control via a USB connection and the synchronization with MS data acquisition. 2) RmsiGUI, which integrates all steps of mass spectrometry imaging: The creation of G-code for robot control, the assembly of imzML files from raw data and the analysis of imzML files. We proved the functionality of the system by the automated sampling and classification of essential oils with a PlasmaChip probe. Further, we performed an ambient ionization mass spectrometry imaging (AIMSI) experiment of a lime slice with laser desorption low-temperature plasma (LD-LTP) ionization, demonstrating the integration of the complete workflow in RmsiGUI. The design of the Open LabBot and the software are released under open licenses to promote their use and adoption in the instrument developers’ community.

We suppose that a Cooper pair (CP) will experience a damping force exerted by the condensed matter. A Langevin equation of a CP in two dimensional condensed matter is established. Following a method similar to Nelson's stochastic mechanics, generalized Schr\"{o}dinger equation of a CP in condensed matter is derived. If the CPs move with a constant velocity, then the corresponding direct current (DC) electrical conductivity can be calculated. Therefore, a Drude like formula of resistivity of CPs is derived. We suppose that the damping coefficient of CPs in two dimensional cuprate superconductors is a linear function of temperature. Then the resistivity and scattering rate of CPs turn out to be also linear-in-temperature. The origin of linear-in-temperature resistivity and Planckian dissipation in cuprate superconductors may be the linear temperature dependence of the damping coefficient of CPs.

(1) Background: A simple approach to map irrigated landcover has been introduced by using measures derived from optical spectral range as an alternative to thermal range. It has been demonstrated that substituting surface temperature (Ts, ‘thermal approach’) with SWIR transformed reflectance (STR, ‘optical approach’) to detect surface moisture is feasible with comparable results. (2) Methods: Using an iterative thresholding procedure to minimize within-class variance, the bilevel segmentation of variables derived from Landsat-8 representing surface moisture and vegetation cover was achieved for the 2020-21 summer for a key irrigation district in Australia. (3) Results: The results of irrigated landcover by optical approach found to be comparable with those by thermal approach. The classification accuracy was assessed using water delivery records at farm level. Though the overall accuracy is high in both cases, the optical approach (97.6%) performed slightly better than the thermal approach (93.9%). (4) Conclusions: The feasibility of using STR to map irrigated landcover has been confirmed by a high-level overall accuracy assessment. This has broader implications in terms of irrigated landcover assessment, as the use of satellite imagery in these applications may not necessarily be limited to microwave or thermal sensors.

Nowadays a recognized need for accurate observations of atmospheric aerosols (AEs) and reactive gases (RGs) exists in the framework of regional, national and global near-surface networks based on permanent or mobile measurement stations. In this context, a paramount and not-trivial issue is related to the correct execution of continuous sampling of ambient air and its subsequent distribution to measurement analyzers hosted inside the stations. Sampling artifacts must be minimized for obtaining reliable pictures of ambient air composition. To respond to this need, a suite of novel “smart” and relatively low-cost systems for the continuous sampling of ambient air was developed in the framework of the Project I-AMICA (2012 – 2015, www.i-amica.eu). These systems were designed to execute AE and RG measurements according with WMO/GAW and ACTRIS recommendations and standard operation procedures. A particular attention was dedicated to the stabilization and control of the sampling flow rates and temperatures. The analysis of one full year of operations at the WMO/GAW regional station of Capo Granitola (GAW ID: CGR, Italy), allowed to conclude that these systems are effective in meeting the technical requirements for correct execution of AE and RG measurements

The Eastern Kunlun Fault Zone (EKFZ) is located in a seismic blank area. This study investigates the hydrogeochemical characteristics of varied-temperature springs in the EKFZ to understand the relationship between fractures, fluids and earthquakes. It aids in establishing their induction mechanisms and assists in monitoring the earthquake precursors of the EKFZ. In this study, the main elements, trace elements, hydrogen and oxygen isotopes and strontium isotopes of 23 varied-temperature springs in the EKFZ were analyzed. The results reveal the source of groundwater recharge, hydrochemical types, mineral saturation, and for a select few springs indicative of geothermal activity, collected geothermal reservoir temperatures. The study also explores the relationship between earthquakes and springs, identifying sensitive chemical indicators. Based on continuous monitoring at Maqu Station, we found that before the occurrence of the Maerkang Ms 6.0 earthquake, the concentration of Cl− rose by 2.9 times, and 46 days before the Gande earthquake (Ms = 4.7), the concentrations of Na+ and SO42− significantly increased. Finally, a conceptual model of the hydrogeochemistry of springs is presented to describe the groundwater circulation in the study area. This research is of great significance for the analysis of fluid geochemistry in this area and for assessing the seismic hazards of the EKFZ.

The use of artificial intelligence technologies may help companies obtain the optimal use of resources and accomplish more activities with an increase in productivity by 40%. With access to real-time data and the ability to learn from patterns and behaviors, AI can perform these routine tasks more efficiently. Ambient intelligence, Ami, is one of the applications of artificial intelligence, which is called artificial environmental intelligence, which is a concept that focuses on using technology to create an environment that is intelligent and responsive to the needs of its users. This technology has the potential to revolutionize disaster response and management, which in turn facilitates access to necessary information and resources. necessary vitality in the event of a crisis. It may use ambient intelligence to create a network of sensors that can detect and respond to changes in the environment. So that this network can be used to monitor the environment for potential disasters, such as floods, fires and earthquakes. Sensors can also be used to detect changes in temperature, humidity, and other environmental factors that may indicate a potential disaster. This information can then be used to alert emergency responders and provide them with the information needed to respond quickly and effectively. Ambient intelligence can also be used to create a comprehensive database of resources and information that can be accessed in times of crisis. This database may include information about the location of shelters, medical facilities, and other resources that can be used to assist those affected by a disaster. It may also provide information about the condition of roads, bridges, and other infrastructure that may be affected by a disaster. This information can be used to inform response and management decisions, helping to ensure that resources are used in the most efficient way possible. Ambient intelligence can be used to create a communication platform between emergency responders and those affected by a disaster. This platform can also be used to provide updates on the emergency situation, in addition to providing information about available resources to those affected. This can help ensure that those affected by a disaster can access the resources they need in a timely manner.

We examined whether the ambient illuminance during extended wakefulness modulates the homeostatic increase in human deep sleep [i.e. slow wave sleep (SWS) and electroencephalographic (EEG) slow-wave activity (SWA)] in healthy young and older volunteers. Thirty-eight young and older participants underwent 40 hours of extended wakefulness [i.e. sleep deprivation (SD)] once under dim light (DL: 8 lux, 2800K), and once under either white light (WL: 250 lux, 2800K) or blue-enriched white light (BL: 250 lux, 9000K) exposure. Subjective sleepiness was assessed hourly and polysomnography was quantified during the baseline night prior to the 40-h SD and during the subsequent recovery night. Both the young and older participants responded with a higher homeostatic sleep response to 40-h SD after WL and BL than after DL. This was indexed by a significantly faster intra-night accumulation of SWS and a significantly higher response in relative EEG SWA during the recovery night after WL and BL than after DL for both age groups. No significant differences were observed between the WL and BL condition for these two particular SWS and SWA measures. Subjective sleepiness ratings during the 40-h SD were significantly reduced under both WL and BL compared to DL, but were not significantly associated with markers of sleep homeostasis in both age groups. Our data indicate that not only the duration of prior wakefulness, but also the experienced illuminance during wakefulness affects homeostatic sleep regulation in humans. Thus, working extended hours under low illuminance may negatively impact subsequent sleep intensity in humans.

As the rapid development of communication industry, especially the 5G communication and IOT, there will be plenty of electromagnetic (EM) waves in the free space, which carry lots of energies. However, some of these energies are wasted in free space. To reuse these wasted energies, significantly growing interests are towards to the energy harvesting antennas. This paper is aimed to investigate a wearable antenna which can transfer RF energy from ambient sources to direct current by a soft and portable textile antenna. Among the numerous signals in mobile network, the GSM 1800, 3G, WiFi and 4G/5G will be chosen due to the city signal intensity distribution. Hence, a corresponding triple bands antenna has been designed to cover those frequency bands. The CST STUDIO SUITE is used in whole process of antenna design and simulation. The proposed antenna is a hooked dipole antenna with tuning bar (HATB) whose ends have small folded part in each side for better bandwidth performance. The presented antenna provides a wide operating band from 1.8 GHz to 2.5 GHz below -10 dB in return loss. And methods to overcome interference between antennas is found. Furthermore, using the corresponding rectifier to achieve the RF/DC conversion. The overall efficiency of whole rectifier is about 56.8 %, and output power level of the antenna system is 45.92nW. The experimental results could indicate that my textile hooked antenna harvester is a good choice for the charging system of personal wearable attachment, which could achieve low power absorbing for long distance anytime and anywhere.

Microwave radiation diagnosis technology can detect thermal changes in skin tissue earlier than anatomical changes, but its detection accuracy is limited by non-target radiation interference in the measurement environment, additional measurement errors of system units, and energy scattering and transmission between skin tissues. This paper aims to address the scientific challenges of analyzing the forward and inversion modelling detection mechanism of layered accurate temperature measurement of human skin tissue based on multi-band. The study focuses on the construction of a pencil beam antenna optimization system, the optimization strategy of high-sensitivity correlated radiometer architecture, and the high-precision multi-band forward and inversion modelling detection algorithm. The key technologies include: (1) A new method of integrated modeling and multi-index optimization of antenna with high directivity and small aperture is proposed, and a priori knowledge-guided neural network of pencil beam distribution is constructed to realize the inversion model of antenna structural parameters; (2) The influence mechanism of high sensitivity correlated radiometer architecture error is analyzed, and a periodic phase shift error correction algorithm based on uniform polar circle is designed; (3) Combining deep learning theory and hyperparameter optimization framework, an iterative model is established, and the objective function modified by the penalty factor is defined to realize a new detection method combining forward and inversion. This paper presents a theoretical foundation for the industrialization of microwave radiation diagnostic technology.

In recent years the number of available chemical pesticides has been significantly reduced and there have been an urgent need for discovery of alternative to chemical pesticides products, as among others the natural zeolites (zeolitic rocks). We determined the mineralogical and chemical composition of a specific and continuous layers of zeolitic rock sample (ZeotP) from Petrota, Ev-ros, Greece and evaluated its oviposition deterrent effect for the olive fruit fly Bactrocera oleae (Diptera: Terphritidae). The tested natural zeolite contained 70 wt. % Clinoptilolite, 18 wt. % Amorphous material, 7 wt. % Feldspars, 4 wt. % Cristobalite and 1 wt. % Quartz. We tested the oviposition deterrent effect of ZeotP mixed or not with an emulsifier adjuvant NU-FILM-P® in water and applied on the surface of olive fruits. The ZeotP oviposition deterrent effect for the ol-ive fly was very high under a series of tested temperatures (17°C, 20°C, 25°C and 30°C) and RHs (23%, 33%, 55%, 75%, 94%). In addition, the ZeotP residual deterrent effect after equable water spraying was high and similar to the respective effect of a pyrethroid insecticide (Decis®). Our results may contribute to an effective control of the olive fruit fly using an alternative to chemical pesticides natural zeolite (zeolitic rocks) product.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

Agaricus bisporus is one of the most popular mushroom species in the world; however, mushrooms are highly susceptible to browning due to the absence of a protective cuticle layer and high respiration rate. The molecular mechanism underlying the process of mushroom browningneeds to be explored. Here, we analyzed the transcriptomic and metabolomic data from A. bisporusat ambient temperature. Specifically, a total of 263 significantly changed metabolites and 4492 differentially expressed genes were identified. Lipid metabolites associated with cell membrane degradation were predominantly up-regulated during ambient storage. Transcriptomic data further revealed the alterations of the expression of membrane lipid metabolism-related enzymes. Additionally, energy metabolic processes and products such as glycolysis and linoleic acid changed significantly during ambient storage, indicating their potential roles in the quality deterioration of A. bisporus. These findings provide new insights into the underlyingl ipidmetabolic mechanism of A. bisporus during postharvest ambient storage and will provide values for mushroom preservation techniques.

This study investigates the effects of ambient illumination and negatively polarized text color on visual fatigue, exploring the issue of visual fatigue when using visual display terminals in low-illumination environments. The research methodology utilized an experimental design to collect data on changes in pupil accommodation and blink rate through an eye tracker. Partici-pants completed a reading task while exposed to various text colors and ambient light conditions to evaluate visual fatigue and cognitive performance. The study's findings suggest that text color significantly affects visual fatigue, with red text causing the highest level of visual fatigue and yellow text causing the lowest level of visual fatigue. Improvements in ambient lighting reduce visual fatigue, but the degree of improvement varies depending on the text color. Additionally, cognitive performance is better when using yellow and white text but worse when using red text. Yellow text is the most effective choice for reducing visual fatigue under negative polarity. In-creasing ambient lighting can also improve visual fatigue in low-illumination conditions. These findings will offer valuable guidance for designing visual terminal device interfaces, especially for low-illumination or night environments, to minimize visual fatigue and improve the user ex-perience.

Elaborate sound design, including background music, ambient sounds (sounds describing the game world), and character sounds (sounds generated by the character’s actions), plays a pivotal role in modern videogames. However, the influence of these different types of sound on the player experience has not been extensively researched. This study examines the influence of these sound types on immersion, avatar identification, fun and perceived competence. In two experiments, participants played League of Legends in four different sound conditions. The first experiment revealed a non-significant trend in the effect of character sound on avatar identification. Ambient sounds, however, were limited in this experiment because the task restricted participants’ movement across the game map. Consequently, we adapted the task to allow for a wider variety of ambient sounds in the second experiment. Here, a significant impact of character sounds on immersion, avatar identification, and fun, was observed, as well as an interaction effect of character sounds and ambient sounds on fun. Furthermore, we observed a trend, though not statistically significant, suggesting that ambient sounds may influence the player’s sense of flow. These findings underline the distinct effects of different sound types and we discuss implications for the design of sound in video games.

Findings from studies of prenatal exposure to pesticides and adverse birth outcomes have been equivocal so far. We examined prenatal exposure to agricultural pesticides in relation to preterm birth and term low birthweight, respectively, in children born between 1998 and 2010 randomly selected from California birth records. We estimated residential exposures to agriculturally applied pesticides within 2 km of residential addresses at birth by pregnancy trimester for 17 individual pesticides and 3 chemical classes (organophosphates, pyrethroids, and carbamates). Among maternal addresses located within 2 km of any agricultural pesticide application, we identified 24,693 preterm and 220,297 term births, and 4,412 term low birthweight and 194,732 term normal birthweight infants. First or second trimester exposures to individual pesticides (e.g., glyphosates, paraquat, imidacloprid) or exposures to 2+ pesticides in the three chemical classes were associated with small increases (3-7%) in risk for preterm birth; associations were stronger for female offspring. We did not find associations between term low birthweight and exposures to pesticides other than for myclobutanil (OR: 1.11; 95% CI: 1.04-1.20) and possibly pyrethroids as a class. Our improved exposure assessment revealed that first and second trimester exposures to pesticides were associated with preterm delivery but few affected term low birthweight.

The bipartite entanglement is comprehensively investigated in the mononuclear molecular complex (Et3NH)[Ni(hfac)2L], where HL denotes 2-(2-hydroxy-3-methoxy-5-nitrophenyl)-4,4,5,5-tetramethyl-4,5-dihydro-1H-imidazol-3-oxide-1-oxyl and hfacH stands for hexafluoroacetylacetone. From the magnetic point of view, the molecular compound (Et3NH)[Ni(hfac)2L] consists of an exchange-coupled spin-1 Ni2+ magnetic ion and a spin-12 nitronyl-nitroxide radical substituted nitrophenol. The nickel-radical molecular complex affords an experimental realization of a mixed spin-(12, 1) Heisenberg dimer with a strong antiferromagnetic exchange coupling J/kB= 505 K and two distinct g-factors gRad=2.005 and gNi=2.275. By adopting this set of magnetic parameters we demonstrate that the Zeeman splitting of a quantum ferrimagnetic ground-state doublet due to a weak magnetic field may substantially reinforce the strength of bipartite entanglement at low temperatures. The molecular compound (Et3NH)[Ni(hfac)2L] maintains sufficiently strong thermal entanglement even at room temperature, vanishing only above 546 K. Specifically, the thermal entanglement in the nickel-radical molecular complex retains approximately 40% of the maximum value corresponding to perfectly entangled Bell states at room temperature, which implies that this magnetic compound provides suitable platform of a molecular qubit with potential implications for room-temperature quantum computation and quantum information processing.

Pakistan relies mostly on fossil fuel for fulfilling its energy demand which is expensive as 11 well as not friendly for the environment. The need of the hour is to shift from fossil fuels to renew-12 able energy resources like geothermal, wind, solar etc. to cater for global warming issues. Pakistan 13 has a lot of potential geothermal sites because of several fault lines and hot springs. A sound 14 knowledge of ground temperature is essential to use geothermal energy, which is obtained by drill-15 ing boreholes and putting sensors making it an expensive procedure. Thus, to avoid huge cost for 16 drilling bore holes, particularly for ground temperature analysis, a numerical approach has been 17 considered for determining ground temperature. Furthermore, correlation charts between air and 18 ground temperatures have been developed as there were no proper studies on the ground temper-19 ature of Pakistan. Then, with the help of a boreholes drilled in National University of Sciences and 20 Technology Islamabad Pakistan, the actual ground and numerically calculated temperatures have 21 been compared which shows an error margin in the range between 0.27% for higher depths to 7.3% 22 near surface. Thus, it is shown that the proposed method is easy to implement and better than large 23 scale testing methods for the depths at which geothermal energy is extracted.

The predatory mirids Macrolophus pygmaeus Ramber and Nesidiocoris tenuis Reuter (Heteroptera: Miridae) are used for the biological control of Tuta absoluta Meyrick (Lep.: Gelechiidae) and other pests in tomato greenhouses. The functional response of 1 (young) and 10 (old) days old adult females and males of M. pygmaeus and N. tenuis on eggs of T. absoluta, was determined on tomato at two temperatures (20° and 25°C) and LD 16:8 and found to be Type II. M. pygmaeus females exhibited higher predation efficiency, than males at both tested temperatures. Young M. pygmaeus females had a higher efficiency than old ones, whereas males had a low efficiency irrespective of age. The predation efficiency of N. tenuis was high (but lower than M. pygmaeus) in both young females and males, although old females had a higher efficiency than the respective males. Our results show that the two predatory species have different functional response characteristics to their prey depending mainly on sex and age which may affect their role as biological control agents.

This study determined the temporal variation of PM2.5 in ambient air in Thohoyandou and further assessed the associated health risks. The levels of PM2.5 were quantified for a period of 1 year (April 2017-April 2018) using the gravimetric method. There was no significant difference (P-value = 0.18) in concentrations of both PM2.5 samples collected during weekdays (11.29 µg.m-3) and weekends (9.86 µg.m-3). However, higher concentrations of PM2.5 were measured in spring and the lowest was measured in summer. The cancer risk obtained for PM2.5 (2.21 × 10−5, 3 × 10-4, and 5 × 10-4 for infants, children, and adults respectively) in the outdoor air of Thohoyandou has exceeded the limit values by the USEPA and WHO, implying a significant risk for the whole population. For non-carcinogenic risks, the HQ values were 2.60, 4.81, and 2.60 for infants, children, and adults respectively. The HQ value >1 indicates a non-carcinogenic risk to the residents in Thohoyandou and a higher risk to children. Moreover, PM2.5 in Thohoyandou is responsible for 0.15% and 0.13% of deaths resulting from cardiovascular disease and lung cancer respectively for adults above 30 years. PM2.5 is causing adverse health effects in Thohoyandou as deduced from the health risk assessment. Therefore, it is recommended that further epidemiological studies be conducted in Thohoyandou to estimate the burden of disease due to exposure to particulate matter and suitable controlling policies be arranged to reduce particulate matter.

With the widespread of embedded sensing capabilities of mobile devices, there has been unprecedented development of context-aware solutions. This allows the proliferation of various intelligent applications such as those for remote health and lifestyle monitoring, intelligent personalized services, etc. However, activity context recognition based on multivariate time series signals obtained from mobile devices in unconstrained conditions is naturally prone to imbalance class problems. This means that recognition models tend to predict classes with the majority number of samples whilst ignoring classes with the least number of samples, resulting in poor generalization. To address this problem, we propose to augment the time series signals from inertia sensors with signals from ambient sensing to train deep convolutional neural networks (DCNN) models. DCNN provides the characteristics that capture local dependency and scale invariance of these combined sensor signals. Consequently, we developed a DCNN model using only inertial sensor signals and then developed another model that combined signals from both inertia and ambient sensors aiming to investigate the class imbalance problem by improving the performance of the recognition model. Evaluation and analysis of the proposed system using data with imbalanced classes show that the system achieved better recognition accuracy when data from inertial sensors are combined with those from ambient sensors such as environment noise level and illumination, with an overall improvement of 5.3% accuracy.

This paper investigates the influence of magnetic field for a two dimensional deformations on a two temperature problem at the free surface of a semi-infinite semiconducting medium under the effect of mechanical force during a photothermal theory and the effect of hydrostatic initial stress on the medium. The Harmonic Wave Method (Normal Mode Analysis) has been used to obtain the equations of elastic waves, heat conduction equation, quasi-static electric field, carrier density, two temperature coefficient, ratios, and constitutive relationships for the thermo-magnetic-electric medium. The effects of several parameters as thermoelastic and thermoelectric coupling parameters and two temperature parameter of this force on the displacement component, force stress, carrier density and temperature distribution has been depicted graphically.

Black soldier fly larvae (BSFL) can use food by-products or residues as a growth substrate, and their use is considered a strategic solution to improve the sustainability and efficiency of animal production. BSFL need to be reared under controlled environmental conditions, as temperature can affect the welfare of the larvae and the efficiency of their bioconversion. The goal of this experiment was to test different diets: control, vegetable, carnivorous, omnivorous and to assess their effect on larval growth performance, chemical composition, and substrate temperature. BSFL (6-days-old) were randomly selected and allocated to one of the four diets for the entire experiment (8 days). The temperature in each container was measured twice daily using a thermal imaging camera. The vegetable diet led to significantly lower growth performance (p

Drivers of L3 automated vehicles (AVs) are not required to continuously monitor the AV system. However, they must be prepared to take over when requested. Therefore, it is necessary to design an in-vehicle environment that allows drivers to adapt their levels of preparedness to the likelihood of control transition. This study evaluates ambient in-vehicle lighting that continuously communicates the current level of AV reliability, specifically on how it could influence drivers' take-over performance and mental workload (MW). We conducted an experiment in a driving simulator with 42 participants who experienced 10 take-over requests (TORs). The experimental group experienced a four-stage ambient light display that communicated the current level of AV reliability, which was not provided to the control group. The experimental group demonstrated better take-over performance, based on lower vehicle jerks. Notably, perceived MW did not differ between the groups, and the EEG indices of MW (frontal theta power, parietal alpha power, Task-Load Index) did not differ between the groups. These findings suggest that communicating the current level of reliability using ambient light might help drivers be better prepared for TORs and perform better without increasing their MW.

In hospitals and smart nursing homes, ambient-intelligent care rooms are equipped with many sensors. They can monitor environmental and body parameters, and detect wearable devices of patients and nurses. Hence, they continuously produce data streams. This offers the opportunity to collect, integrate and interpret this data in a context-aware manner, with a focus on reactivity and autonomy. However, doing this in real-time on huge data streams is a challenging task. In this context, cascading reasoning is an emerging research approach that exploits the trade-off between reasoning complexity and data velocity by constructing a processing hierarchy of reasoners. Therefore, a cascading reasoning framework is proposed in this paper. A generic architecture is presented allowing to create a pipeline of reasoning components hosted locally, in the edge of the network, and in the cloud. The architecture is implemented on a pervasive health use case, where medically diagnosed patients are constantly monitored, and alarming situations can be detected and reacted upon in a context-aware manner. A performance evaluation shows that the total system latency is mostly lower than 5 seconds, allowing for responsive intervention by a nurse in alarming situations. Using the evaluation results, the benefits of cascading reasoning for healthcare are analyzed.

The aim of this research work is to study the influence of temperature, solar irradiation and wind dust on the production of solar energy. In addition, it aims to study the assessment of water quality, in particular groundwater used for cooling and cleaning photovoltaic panels (quality analysis). it's an important source, stable and sustainable can be used entirely for cooling and cleaning PV modules from the sales dust, in order to improve their performance. To date, all research studies carried out in this context of cooling and cleaning using water have not taken account of the nature of this water. We have taken a sample of water from a well in a rural area in the Darra Tafilalet region of Morocco. This region has an arid and semi-arid climate, with very high temperatures and dust-laden winds, particularly in summer. These meteorological characteristics influence the efficiency of cells, particularly photovoltaic (PV) panels, reducing their performance. Next, the water sample was analysed in the laboratory. The results obtained show that the groundwater in this area is very sensitive to cooling and cleaning photovoltaic panels. Moreover, these results indicate that the temperature, solar irradiation and wind-blown dust have a significant influence on energy production.

The temperature effect plays an important role for an accurate determination of the polar free energy, polar thermodynamic parameters, and enthalpic and entropic Lewis’s acid base properties of oxides, polymers and composites polymers/oxides. The adsorption of polymers on other solid surfaces is crucial in many industrial applications, coatings, paints, catalysis, colloids and adhesion processes. (1) Background: Inverse gas chromatography at infinite was used for the physico-chemical characterization of solid substrates by determining the thermodynamic parameters of adsorption of model organic solvents on solid surfaces such as polymers, metallic oxides, carbon fibers, pharmaceutical or 3D/4D printing substrates. (2) Methods: A new method based on the London dispersion equation was applied with a new parameter associating the deformation po-larizability and the harmonic mean of the ionization energies of solvent. More accurate values of the dispersive and polar interaction energies of the various organic solvents adsorbed on PMMA in bulk phase and PMMA/silica at different recovery fractions were obtained as well as the Lewis acid-base parameters and the transition temperatures of the different composites. (3) Results: This new methodology gave very interesting results on the behavior of PMMA adsorbed on silica. An important effect of the temperature and the recovery fraction on the various physicochemical and thermodynamic properties was highlighted. The variations of all interaction parameters showed the presence of three transition temperatures for the different PMMA adsorbed on silica with the various coverage rates with a shift of these temperatures for a recovery fraction of 31% (4) Con-clusions: An important variation of the polar enthalpy and entropy of adsorption, the Lewis ac-id-base parameters and the intermolecular separation distance as a function of the temperature and the recovery fraction of PMMA on silica.

PM_0.1 (particles diameter ≤ 0.1 µm), nanoparticles (NPs), and ultrafine particles (UFPs), were interchangeably used in the scientific communities. PM_0.1 originated from both natural and human sources. However, investigations of PM_0.1 and its effects on the environment, visibility, and human health risk to understand the levels of air pollution, sources, and impacts in South East Asia (SEA) countries continue to be lacking. The concentration of PM_0.1 in most SEA countries are much worse than those in western countries environment. A further motivation of this reviewed article is to provide a critical synthesis of the current knowledge and study of ambient PM_0.1 in SEA cities. The main influence of characteristics of PM_0.1 appears to be local sources including biomass burning and motor vehicles. Continuous monitoring of PM_0.1 in terms of both mass and number concentration should be further understood. A critical review is of great importance to facilitating air pollution control policies and predicting the behavior of PM_0.1 in SEA.

Background: Lung cancer is one of the leading causes of morbidity and mortality worldwide with 25% of deaths due to lung cancer occurring in Europe. This study therefore sought to assess the burden of lung cancer by country and to evaluate the magnitude of fine Particulate Matter (PM2.5) and cigarette smoking by country in Europe. Methods: An ecological study nested on the World Health Organization air pollution database 2016 was conducted. We sampled 30 European Countries, with a total of 1625 mean annual samples of Particulate Matter (PM2.5) collected from 1625 designated sites (n = 1625). We further used the ‘World Health Disease Rankings’ database to extract Lung Cancer Morbidity and Mortality Rate by country. We used SAS version 9.4 to indicate the distribution of PM2.5 and Lung Cancer Mortality Rate. Results: Lung cancer Relative Risk (RR) was 1.0 in all never- smokers. RR for Ex-smokers for Adeno carcinoma was 3.5 in males and 1.1 in females, small cell carcinoma was 16.2 in males and 3.8 in females. RR for current smokers for Adeno carcinoma was 8.0 in males and 4.1 in females, small cell carcinoma was 57.9 in males and 18.2 in females. Mean annual PM2.5 by country ranged from 6.01 to 37.28µg/m3 whereas lung cancer mortality rate by country ranged from 19.67 to 54.26 deaths per 100,000 population. Conclusion: Cigarette smoking and exposure to both second hand smoke and high concentration of PM2.5 resulted into increased burden of lung cancer in Europe. Countries should re-strategize to reduce the burden of lung cancer in Europe.

Pulmonary hypertension (PH) has a high mortality, and few treatment options. Adaptive immune mediators of PH in mice challenged with antigen/particulate matter (antigen/PM) has been the focus of our prior work. We identified key roles of type 2 and type 17 responses in C57BL/6 mice. Here, we focused on type 2 response related cytokines, specifically Resistin-like-molecule (RELM)α, a critical mediator of hypoxia-induced PH. Because of strain differences in the immune responses to type 2 stimuli, we compared C57BL/6J and BALB/c mice. A model of intraperitoneal antigen sensitization with subsequent, intranasal challenges with antigen/PM (ovalbumin and urban ambient PM2.5) or saline was used in C57BL/6 and BALB/c wild type or RELMα-/- mice. Vascular remodeling was assessed by histology, right ventricular (RV) pressure, RV weights and cytokines were quantified. Upon challenge with antigen/PM2.5, both C57BL/6 and BALB/c mice developed pulmonary vascular remodeling; these changes were more prominent in the C57BL/6 strain. Compared to wild type mice, RELMα-/- had significantly reduced pulmonary vascular remodeling in BALB/c, but not in C57BL/6 mice. RV weights, RV IL-33 and RV ST2-IL-33-receptor were significantly increased in BALB/c wild type mice, but not in BALB/c-RELMα-/- or in C57BL/6-wild type or C57BL/6-RELMα-/- mice. RV systolic pressures (RVSP) were higher in BALB/c compared to C57BL/6J mice, and RELMα-/- were not different from their respective wild type controls. In BALB/c mice, RELMα was a key contributor to antigen/PM2.5 induced pulmonary vascular remodeling, RV thickening and RV cytokine responses, highlighting the significance of the genetic background. The RELMα-/- animals demonstrated significantly decreased expression of RELMβ and RELM which makes these mice comparable to a situation where human RELMα levels would be significantly modified, as humans only have one RELM molecule.

The previous studies on the diversion pipe of pumped storage power stations (PSPS) primarily focused on numerical simulations of pulsating pressure propagation within the pipe and its inducing factors. However, there was a lack of field monitoring and analysis of measured data to support surface ambient vibration, resulting in insufficient credibility and practicality of the numerical results. Based on ambient monitoring and data analysis, this paper examines the factors contributing to the ambient vibration of the water diversion pipeline in Changlongshan (CLS) PSPS. It is concluded that: (1) The primary source of vibration originates from units operation-induced ambient vibrations; (2) Vibration during pumping conditions exceeds that during power generation conditions; (3) The ground measuring point's vibration acceleration primarily depends on the distance from the vibration source; (4) Different types of units have varying effects on water diversion pipeline vibrations.

(1) Background: Environmental and public health research has given considerable attention to the impact of air quality on brain health, with systematic reviews widespread. No literature review has been done for cognitive frailty – a multidimensional syndrome combining physical frailty and cognitive impairment and their apparent co-dependence, linked to increased vulnerability and adverse health outcomes, including dementia. Instead, cognitive decline and frailty is implicitly explored through research on air quality and comorbid cognitive and physical decline in elderly populations. (2) Methods: A scoping review was conducted to explore the need for a systematic review. Combining Arksey and O’Malley [1] and PRISMA-ScR checklist [2], a scoping review of SCOPUS using ‘cogniti*’ + ‘resilience’ + ‘air quality’ or ‘cogniti*’ + ‘ageing’ + ‘air quality’ resulted in N=2503 articles, screened and reduced using inclusion and exclusion criteria, to N=16 articles. (3) Results: Air quality appears to be a critical risk factor for cognitive decline, even at air quality levels below WHO targets. Moderate long-term ambient air pollution appears linked to increased risk of cognitive frailty, suggesting earlier and more active interventions to protect older people. There are varied effects on cognition across the life course, with both emotional and functional impacts. Effects may be more detrimental to elderly people with existing conditions, including economic and health inequalities. Generalisation of results is limited due to the absence of a dose-response, variations in methods, controlling for comorbid effects, and variance across studies. (4) Conclusions: The findings support the need for more research and a more extensive summary of the literature.

For the first time, it is shown that inhaled ambient air-dust particles settled in the human lower respiratory tract induce lung calcification. Chemical- and mineral compositions of pulmonary calcium precipitates in the lung right lower-lobe (RLL) tissues of 12 individuals who lived in Upper Silesia Conurbation in Poland and who had died from causes not related to lung disorder were determined by transmission- and scanning electron microscopy. Whereas calcium salts in lungs are usually reported as phosphates, calcium salts precipitated in RLL are almost exclusively carbonates, i.e. Mg-calcite and calcite. These constitute 37% of 1652 mineral particles examined. Mg-calcite predominates in the submicron size range with the MgCO3 content up to 50 mol%. Magnesium plays a significant role in the lung mineralization, a fact so far overlooked. The calcium phosphate (hydroxyapatite) content in RLL is negligible. The predominance of carbonates is explained by increased CO2 fugacity in RLL. Carbonates enveloped inhaled mineral-dust particles, including uranium-bearing oxides, quartz, aluminosilicates, and metal sulfides. Three possible pathways for the carbonates precipitation on the dust particles are postulated: (1) precipitation of amorphous calcium carbonate (ACC) followed by its transformation to calcite; (2) precipitation of Mg-ACC followed by its transformation to Mg-calcite; (3) precipitation of Mg-free ACC causing a localized relative enrichment in Mg ions and subsequent heterogeneous nucleation and crystal growth of Mg-calcite. The actual number of inhaled dust particles may be significantly greater than observed because of the masking effect of the carbonate coatings. There is no simple correlation between smoking habit and lung calcification.

A temperature-modulated pyroelectricity measurement system for a small single crystal is developed and applied to standard sample measurements performed on a thin single crystal of lithium niobate. The modulation measurement is based on the AC technique, in which the temperature of the sample is periodically oscillated, and the synchronized pyroelectric signal is extracted using a lock-in amplifier. Temperature modulation is applied by irradiating periodic light on the sample placed in the heat exchange gas. To apply this technique to the transparent reference sample, a commercially available black resin is coated on the sample’s surface to absorb the light energy and transmits it to the specimen. The experimental results are analyzed using a two-layer heat transfer model to verify the effect of the light-absorbing layer as well as the non-contact temperature modulation system.

The results of numerical experiments with the chemistry-climate model of the Institute of Numerical Mathematics of the Russian Academy of Sciences - Russian State Hydro-Meteorological University (INM-RSHU CCM) in comparison with the MERRA2 reanalysis data are presented. To assess the impact of sea surface temperature (SST) on stratospheric processes and the ozone layer, numerical experiments were carried out for scenarios corresponding to the El Niño and La Niña Southern Oscillation phases. It is shown that the El Niño phase contributes to the enhancement of heat and mass transfer to the polar stratosphere, which strengthen the Brewer-Dobson circulation and the flux of wave activity that affect the zonal wind. As a result, during El Niño, the probability of sudden stratospheric warming increases and the stratospheric polar vortex (SPV) weakens, re-sulting in an increase in total polar stratospheric ozone. The La Niña phase, on the contrary, is accompanied by a weakening of heat and mass transfer from the troposphere to the stratosphere, as a result of which the stratospheric polar vortex strengthens and the total column ozone decreases. It is shown that the effect associated with the Southern Oscillation is more pronounced in the Northern Hemisphere than in the Southern Hemisphere. Numerical experiments were also carried out for scenarios in which the sea surface temperature was set corresponding to the early 1980s, and the results were compared with calculations in which the SST was set corresponding to the late 2010s. This allowed us to assess the influence of the multiyear trend in the SST increase on stra-tospheric processes and the ozone layer. It was shown that the SST increase is most pronounced in the Arctic, which corresponds to the phenomenon of "Arctic amplification", and therefore, the heat and mass transfer to the stratosphere increases in the Northern Hemisphere, which contributes to some weakening of the SPV and increase of the total column ozone. But, compared to the Southern Oscillation, the influence of the SST trend on the SPV and total column ozone is much weaker and is observed mainly in the Northern Hemisphere.

The new Internet of Things (IoT) applications are enabling the development of projects that help monitoring people with different diseases in their daily lives. Alzheimer’s is a disease that affects neurological functions and needs support to maintain maximum independence and security of patients during this stage of life, as the cure and reversal of symptoms have not yet been discovered. The IoT-based monitoring system provides the caregivers’ support in monitoring people with Alzheimer’s Disease (AD). This paper presents an ontology-based computational model which receives physiological data from external IoT applications, allowing to identify of potentially dangerous behaviors for patients with AD. The main scientific contribution of this work is the specification of a model focusing on Alzheimer’s disease using the analysis of Context Histories and Context Prediction, which considering the state of the art, it is the only one that uses analysis of Context Histories to perform predictions. The research also proposes a simulator to generate activities of the daily life of patients allowing the creation of datasets. These datasets were used to evaluate the contributions of the model and were generated according to the standardization of the ontology. The simulator generated 1025 scenarios applied to guide the predictions, which achieved average accurary of 97.44%. The experiments also allowed the learning of 20 relevant lessons on technological, medical and methodological aspects of DCARE that are recorded in this article.

Continuous in-home monitoring of older adults living alone aims to improve their quality of life and independence, by detecting early signs of illness and functional decline or emergency conditions. To meet requirements for technology acceptance by seniors (unobtrusiveness, non-intrusiveness, privacy-preservation), this study presents and discusses a new smart sensor system for the detection of abnormalities during daily activities, based on ultra-wideband radar providing rich, not privacy-sensitive, information useful for sensing both cardiorespiratory and body movements, regardless of ambient lighting conditions and physical obstructions (through-wall sensing). The radar sensing is a very promising technology, enabling the measurement of vital signs and body movements at a distance, and thus meeting both requirements of unobtrusiveness and accuracy. In particular, impulse-radio ultra-wideband radar has attracted considerable attention in recent years thanks to many properties that make it useful for assisted living purposes. The proposed sensing system, evaluated in meaningful assisted living scenarios by involving 30 participants, exhibited the ability to detect vital signs, to discriminate among dangerous situations and activities of daily living, and to accommodate individual physical characteristics and habits. The reported results show that vital signs can be detected also while carrying out daily activities or after a fall event (post-fall phase), with accuracy varying according to the level of movements, reaching up to 95% and 91% in detecting respiration and heart rates, respectively. Similarly, good results were achieved in fall detection by using the micro-motion signature and unsupervised learning, with sensitivity and specificity greater than 97% and 90%, respectively.

Keywords: keyword 1; keyword 2; keyword 3 (List three to ten pertinent keywords specific to the article yet reasonably common within the subject discipline.)

Chronic heat stress (CHS) has been exerting great pressure on the poultry industry due to the global warming. CHS-induced negative impacts deeply change the physiology, metabolism, egg production and meat quality of ducks. To reduce the increasing economic loss, different environmental strategies have been adopted. Here, we comprehensively compared three rearing modes for Cherry-Valley ducks (CVds) mainly by changing the environmental temperature. Plus, the transcriptome analysis and physiological anatomy were implied to investigate the underlying molecular biology and pneumonocyte dynamics. It turns out that the CVds affected by CHS have poor growth performance and bad carcass traits. In addition, the irreversible damage caused by CHS in the lung tissue of CVds was observed. Furthermore, several potential genes related to CHS have been found, such as HSPA8, IGF1, FGFR1, ACSL3, ACSL6, NR1H3 and GAPDH. This study strongly indicates the severe injury of CHS from the high-temperature environment and points out one of the adopting directions for duck rearing.

Several studies have identified a relationship between air pollution and depression, particularly in relation to fine particulate matter (PM2.5) exposure. However, the strength of this association appears to be moderated by variables such as age, gender, genetic vulnerability, physical activity and climatic conditions, and has not been assessed at a cross-national level to date. The current study examines the association between the prevalence of depression in each country, based on the most recent Global Burden of Disease Study data, and the average national level of PM2.5 based on the World Health Organization’s database. The observed associations were adjusted for age, gender, level of physical activity, income, education, population density, climate, and type of depression. It was observed that there was a modest but significant positive correlation between PM2.5 level and the prevalence of depression even after adjusting for the above confounders. This association was more marked above a certain threshold and applied chiefly to major depressive episodes. These findings are of significant public health importance in terms of preventive strategies aimed at reducing the population-level burden of depression.

Exposure to traffic-related air pollution is linked with acute alterations in blood pressure (BP). We examined the cumulative short-term effect of black carbon (BC) exposure on systolic (SBP) and diastolic (DBP) BP and assessed effect modification by participant characteristics. SBP and DBP were repeatedly measured on 152 traffic enforcers. Using a linear mixed-effects model with random intercepts, quadratic (QCDL) and cubic (CCDL) constrained distributed lag models were fitted to estimate the cumulative effect of BC concentration on SBP and DBP during the 10-hours (daily exposure) and 7-days (weekly exposure) before the BP measurement. Ambient BC was related to increased BP with QCDL models. An interquartile range change in BC cumulative during the 7-days before the BP measurement was associated with increased BP [1.2% change in mean SBP, 95% confidence interval (CI), 0.1 to 2.3; and 0.5% change in mean DBP, 95% CI, –0.8 to 1.7]. Moreover, the association between the 10-hours cumulative BC exposure and SBP was stronger for females (4.0% change, 95% CI: 2.1–5.9) versus males, and for obese (2.9% change, 95% CI: 1.0–4.8) vs. non-obese traffic enforcers. Short-term cumulative exposure to ambient traffic-related BC could bring about cardiovascular diseases through mechanisms involving increased BP.

The accurate wellbore pressure control not only prevents from lost circulation/blowout and fracturing formation by managing density of drilling fluid, but also improves productivity by mitigating reservoir damage. The geothermal pressure calculated by constant parameters for geothermal well would bring big error easily, as the changes of physical, rheological and thermal properties of drilling fluids with temperature were neglected. This paper researches the wellbore pressure coupling by calculating the temperature distribution with existed model, fitting the rule of density of drilling fluid with temperature and establishing mathematical models to stimulate the wellbore pressures, which is expressed as the variation of Equivalent Circulating Density (ECD) under different conditions. With this method, temperature and ECDs in the wellbore of the first medium-deep geothermal well ZK212 Yangyi Geothermal Field in Tibet were determined, and the sensitivity analysis was simulated by assumed parameters, i.e. circulating time, flow rate, geothermal gradient, diameters of wellbore, rheological models and regimes, the results indicated the geothermal gradient and flow rate were the most influence parameters on the temperature and ECD distribution, and additives added in drilling fluid should be careful which would change the properties of drilling fluid and induce the temperature redistribution. To make sure the safe drilling, velocity of pipes tripping into the hole, depth and diameter of wellbore are considered to control the surge pressure.

Photonic sensors are innovative devices that leverage the principles of light-matter interaction to enable precise and efficient detection of various physical parameters. These sensors operate by exploiting the interaction between photons, the fundamental particles of light, and matter. The light propagates through an optical waveguide, and a portion of the electromagnetic field extends beyond the waveguide surface, forming the evanescent field. This evanescent field interacts with the surrounding medium, allowing for highly sensitive detection of changes in the refractive index or properties of nearby substances. The underlying concept involves the modulation of light properties, such as intensity, wavelength, or phase, when it interacts with a target substance or undergoes changes in the surrounding environment. The advancements in photonic sensor technology have paved the way for enhanced sensitivity, selectivity, and miniaturization, making them invaluable tools in diverse industries. The ability to harness light-matter interactions for sensing purposes not only facilitates highly sensitive measurements but also allows for non-intrusive and remote monitoring, contributing to the evolution of smart and connected systems. In this overview, the material platforms and waveguide structures are explored that can make highly sensitive photonic devices applied to gas and biosensing applications.

Deep neural networks (DNNs) have gained prominence in addressing regression problems, offering versatile architectural designs that cater to various applications. In the field of earthquake engineering, seismic response prediction is a critical area of study. Simplified models such as single-degree-of-freedom (SDOF) and multi-degree-of-freedom (MDOF) systems have traditionally provided valuable insights into structural behavior, known for their computational efficiency facilitating faster simulations. However, these models have notable limitations in capturing the nuanced nonlinear behavior of structures and the spatial variability of ground motions. This study focuses on leveraging ambient vibration (AV) measurements of buildings, combined with earthquake (EQ) time-history data, to create a predictive model using a neural network (NN) in image format. The primary objective is to predict a specific building's earthquake response accurately. The training dataset consists of 1,197 MDOF 2D shear models, generating a total of 32,319 training samples. To evaluate the performance of the proposed model, termed MLPER (Machine Learning based Prediction of building structures' Earthquake Response), several metrics are employed. These include mean absolute percentage error (MAPE) and mean deviation angle (MDA) for comparisons in the time domain. Additionally, we assess magnitude-squared coherence values and phase differences (Δφ) for comparisons in the frequency domain. This study underscores the potential of MLPER as a reliable tool for predicting building earthquake response, addressing the limitations of simplified models. By integrating AV measurements and EQ time-history data into a neural network framework, MLPER offers a promising avenue for enhancing our understanding of structural behavior during seismic events, ultimately contributing to improved earthquake resilience in building design and engineering.

The ambient air quality data for particulate matter as well as criteria of gaseous pollutants were assembled during December 2013 to December 2015 from the Continuous Air Quality Monitoring Station (CAMS) located at Agrabad, Chittagong. The observation showed that during April- October, 24 hour average concentration of PM10 and PM2.5 were within the National Ambient Air Quality Standard (NAAQS) level but it increased occasionally by more than two and a half times during the whole non-monsoon period (November-March). The highest values found of PM2.5 were 321.1 µg/m³ in January, 2013 and 220.34 µg/m³ in December 2015. Whether, the highest alarming concentration of PM10 was reported as 474 µg/m3 in January 2007. The other gaseous pollutants such as SO₂, NO₂, O₃, CO and Hydrocarbons remain well within the permissible limit except dry non-monsoon period. The yearly average increase of Air Quality Index (AQI) value indicates the growth rate of air pollution in Chittagong city. The main responsible pollutant for air pollution is found PM_2.5.

The meaning and evolution of the notion of “temperature” (which is a key concept for the condensed and gaseous matter theories) is addressed from the different points of view. The concept of temperature turns out to be much more fundamental than it is conventionally thought. In particular, the temperature may be introduced for the systems built of “small” number of particles and particles in rest. The Kelvin temperature scale may be introduced into the quantum and relativistic physics due to the fact, that the efficiency of the quantum and relativistic Carnot cycles coincides with that of the classical one. The relation of the temperature to the metrics of the configurational space describing the behavior of system built from non-interacting particles is demonstrated. The Landauer principle asserts that the temperature of the system is the only physical value defining the energy cost of isothermal erasing of the single bit of information. The role of the temperature the cosmic microwave background in the modern cosmology is discussed.

Introduction: Ambient air pollution is major global health problem and commercial drivers are particularly exposed to it. No systematic assessment of the health risks associated with occupational exposure to ambient air pollution in this population has been carried out. Methods: We conducted a systematic review using a protocol-driven strategy. Papers published from inception to 20th April 2018 in MEDLINE, EMBASE, CINAHL, African journals online, Cochrane library, ISRCTN and WHO ICTRP databases were screened for inclusion by two independent reviewers. Original articles with at least an available abstract in English or French were included. Results: The initial search retrieved 1454 published articles of which 20 articles were included. 3 Studies reported a significant difference in white blood cells (106/L) among commercial motorcyclists compared to rural inhabitants (5.041±1.209 vs 5.900±1.213,p=0.001), an increased risk of lung cancer (RR=1.6, 95%CI 1.5-1.8) in bus drivers and an increased standardized mortality ratio (SMR) in bus drivers from Hodgkin’s lymphoma (SMR 2.17, 95%CI 1.19-3.87) compared to white collar workers. Other studies also found that drivers had more oxidative DNA damage and chromosome breaks. 4 papers failed to demonstrate that the drivers were more exposed to air pollution than the controls. 3 other studies also reported no significant difference in lung function parameters and respiratory symptoms. The genetic polymorphisms of detoxifying enzymes were not also homogeneously distributed compared to the controls. Conclusion: There is some evidence that occupational exposure to ambient air pollution among commercial drivers is associated with adverse health outcomes but the existing literature is limited with few studies of small sample size, methodological weaknesses and contradictory findings. Further research is recommended.

Based on a constant volume combustion chamber, the initial ambient pressure effect on combustion performance and flame propagation of the active and passive pre-chamber ignition systems were studied. Compared with the passive pre-chamber, the active pre-chamber can significantly expand the lean combustion limit, enhance the ignition and combustion performance, and speed up the combustion of the main combustion chamber. At slightly lean combustion conditions, the heat release performance has a positive correlation with the initial ambient pressure. As the premixed λ increases, the heat release performance and the initial ambient pressure begin to become negatively correlated. Ignition delay can be minimized by controlling the excess air coefficient in the pre-chamber close to the stoichiometric ratio. The high ambient pressure in the constant volume chamber greatly reduces the mixture entrainment ability of the jet flame at lean combustion conditions, thereby reducing the combustion speed and peak heat release rate.

The purpose of this study is to characterize atmospheric pollution and its sources in two West African urban sites during the dry season (January 2009 in Bamako, Mali, and December 2009 in Dakar, Senegal). Particulate Matter (PM) source apportionment was performed using Principal Component Analysis (PCA) and Positive Matrix Factorization (PMF). Carbonaceous components, water-soluble inorganic compounds, and trace elements were analyzed from PM (TSP, PM10, and PM2.5) samples. The measured PM2.5 and PM10 concentrations were 5 to 10 times and 3 to 8 times higher than the 2005 WHO 24-hour standards, respectively. PCA and PMF analyses identify five sources in both cities. The sources contributing to aerosol concentrations (PM2.5 - PM10) in Bamako are motor vehicles (20-13%), solid fuel combustion (16-13%), crustal dust (24-30%), resuspended road dust (26-30%) and secondary aerosols (10-16%). During the sampling period in Bamako, dust was the most prevalent source, accounting for 63% of the total PM10 mass. In Dakar, the main identified sources were motor vehicles (28-19%), mineral dust (16-25%), industries and oil burn-ing (11-10%), sea salts (15-20%), and resuspended road particles (21-29%). The findings also indicate that anthropogenic emissions contribute significantly to the PM2.5 fraction, implying that populations are highly exposed to fine particles.

Falls, highly common in the constantly increasing global aging population, can have a variety of negative effects on their health, well-being, and quality of life, including restricting their capabilities to conduct Activities of Daily Living (ADLs), which are crucial for one’s sustenance. Timely assistance during falls is highly necessary, which involves tracking the indoor location of the elderly during their diverse navigational patterns associated with ADLs to detect the precise location of a fall. With the decreasing caregiver population on a global scale, it is important that the future of intelligent living environments can detect falls during ADL.s while being able to track the indoor location of the elderly in the real world. Prior works in these fields have several limitations, such as – the lack of functionalities to detect both falls and indoor locations, high cost of implementation, complicated design, the requirement of multiple hardware components for deployment, and the necessity to develop new hardware for implementation, which make the wide-scale deployment of such technologies challenging. To address these challenges, this work proposes a cost-effective and simplistic design paradigm for an Ambient Assisted Living system that can capture multimodal components of user behaviors during ADLs that are necessary for performing fall detection and indoor localization in a simultaneous manner in the real world. Proof of concept results from real-world experiments are presented to uphold the effective working of the system. The findings from two comparison studies with prior works in this field are also presented to uphold the novelty of this work. The first comparison study shows how the proposed system outperforms prior works in the areas of indoor localization and fall detection in terms of the effectiveness of its software design and hardware design. The second comparison study shows that the cost for the development of this system is the least as compared to prior works in these fields, which involved real-world development of the underlining systems, thereby upholding its cost-effective nature.

Urban cities in sub-Saharan Africa (SSA) are faced with ambient air pollution. This is an important public health problem with models and limited monitoring data indicating high concentrations of pollutants such as fine particulate matter (PM_2.5). Going through most global air quality index maps, however, information about ambient pollution from SSA is scarce. We evaluated the feasibility and practicality of longitudinal measurements of ambient PM_2.5 using low-cost air quality sensors (Purple Air-II-SD) across thirteen locations in seven countries in SSA. Devices were used to gather data over a 30-day period with the aim of assessing the efficiency of its data recovery rate and identifying challenges experienced by users in each location. The median data recovery rate was 94% (range: 72% to 100%). The mean 24-hour concentration measured across all sites was 38 µg/m³ with the highest PM_2.5 period average concentration of 91 µg/m³ measured in Kampala, Uganda and lowest concentrations of 15 µg/m³ measured in Faraja, The Gambia. Kampala-Uganda and Nnewi-Nigeria recorded the longest periods with concentrations>250µg/m³. Power outages, SD memory card issues, internet connectivity problems and device safety concerns were important challenges experienced when using Purple Air-II-SD sensors. Despite some operational challenges, this study demonstrated that it is reasonably practicable and feasible to establish a network of low-cost devices to provide data on local PM_2.5 concentrations in SSA countries. Such data are crucially needed to raise public-, societal and policymaker awareness about air pollution across SSA.

Air pollution is a leading cause of death in the United States, and is associated with adverse health outcomes, including increased vulnerability to coronavirus disease 2019 (COVID-19). The AirBeam2 was used to measure particulate matter with a diameter of 2.5 micrometers or smaller (PM2.5), to investigate differences between indoor and ambient levels at seven private homes in New York during and after the COVID-19 lockdown. Measurements taken in 2020 winter, spring and fall and in fall 2022 showed that 90% of the time, indoor PM2.5 levels exceeded outdoor levels both during and after the COVID-19 lockdown, p = 0.03, and exceeded safety levels. Higher indoor PM2.5 levels attributed to little or no ventilation from cooking and smoke in the kitchen and basements, were significantly greater in fall than in winter. Higher ambient PM2.5 levels were attributed to vehicular traffic at a street-facing sampling site. PM2.5 sources identified in this study may help in devising control strategies to improve indoor air quality (IAQ), and consequently alleviate respiratory health effects. These findings may be used as a basis for in-house modifications including natural ventilation and use of air purifiers to reduce exposures, mitigate future risks, and prevent potential harm to vulnerable residents.

Magnetic sensors are widely used in health management systems for turbomachinery, but their applications in the hot zone are limited due to the loss of magnetic properties by permanent magnets with increasing temperature. The paper presents and verifies models and design solutions aimed at improving the performance of an inductive sensor for measuring the motion of rotating objects operating at elevated temperatures (200-1000C), such as compressor and turbine blades. Physical, analog and mathematical models of the interaction of blades with the sensor were developed. A prototype of the sensor was made and its tests were carried out on the RK-4 rotor rig for the speed of 7000 rpm, in which the temperature of the sensor head was gradually increased to 1100C. The sensor signal level was compared to that of an identical sensor operating at room temperature. The heated sensor works continuously producing the output signal whose level does not change significantly. What is more, a set of six probes passed an initial engine test in an SO-3 turbojet. It was confirmed that the proposed design of the inductive sensor is suitable for blade health monitoring of the last stages of compressors, steam turbines as well as previous generation gas turbines operating below 1000C, even without a dedicated cooling system. In real-engine applications, sensor performance will depend on how the sensor is installed and the available heat dissipation capability

By taking advantage of a stability criterion established recently, the critical temperature T_c is reckoned with help of the microscopic parameters, characterising the normal and superconducting electrons, namely the independent-electron band structure and a repulsive two-electron force. The emphasis is laid on the sharp T_c dependence upon electron concentration and inter-electron coupling, which might offer a practical route toward higher T_c values and help to understand why high-T_c compounds exhibit such remarkable properties.

ZnO has many technological applications which largely depend on its properties that can be tuned by controlled synthesis. Ideally, the most convenient ZnO synthesis is carried out at room temperature in aqueous solvent. However, the correct temperature values are often loosely defined. In the current paper we performed synthesis of ZnO in aqueous solvent, by varying reaction and drying temperature by 10°C steps and monitored the synthesis products primarily by XRD. We found out that a simple direct synthesis of ZnO, without additional surfactant, pumping of freezing, required both a reaction (TP) and a drying (TD) temperature of 40°C. Higher temperatures also afford ZnO, but lowering any of the TP or TD below the threshold value results either in the achievement of Zn(OH)2 or in a mixture of Zn(OH)2/ZnO. A more detailed Rietveld analysis of the ZnO samples reveals a density variation with the synthesis temperature and an increase of the nanoparticles average size also verified by SEM images. The optical properties of ZnO obtained by UV-Vis reflectance spectroscopy indicate a red shift of the band gap by ~0.1 eV.

Rice production, owing to its high-water requirement for cultivation, is very vulnerable to the threat of changing climate, particularly prolonged drought and high temperature. Such threats heighten the need for abiotic stress-resilient rice varieties with better yield potential. This review examines the physiological and molecular mechanisms of rice varieties to cope with stress conditions of drought (DS), high temperature (HTS) and their combination (DS-HTS). It appraises research studies in rice about its various phenotypic traits, genetic loci and response mechanisms to stress conditions to help craft new breeding strategies for rice varieties with improved resilience to abiotic stresses. This review consolidates available information on promising rice cultivars with desirable traits as well as advocates synergistic and complementary approaches in molecular and systems biology to develop new rice breeds that favorably respond to climate-induced abiotic stresses. The development of new breeding and cultivation strategies for climate-resilient rice varieties is a challenging task. It requires a comprehensive understanding of the various morphological, biochemical, physiological, and molecular components governing yield under drought and high temperature, but possible by implementing cohesive approaches involving molecular and systems biology approaches in genomics and molecular breeding, including genetic engineering.

The concentration of total suspended particles (TSP) and nanoparticles (PM0.1) over Hat Yai city, Songkhla province, southern Thailand was measured in 2019. Organic carbon (OC) and elemental carbon (EC) were evaluated by carbon aerosol analyzer (IMPROVE-TOR) method. Thirteen trace elements including Al, Ba, K, Cu, Cr, Fe, Mg, Mn, Na, Ni, Ti, Pb, and Zn were evaluated by ICP-OES. Annual average TSP and PM0.1 mass concentrations were determined to be 58.3 ± 7.8 and 10.4 ± 1.2 µg/m3, respectively. The highest levels of PM occurred in the wet season with the corresponding values for the dry seasons being lower. The annual average OC/EC ratio ranged from 3.8 - 4.2 (TSP) and 2.5 - 2.7 (PM0.1). The char to soot ratios were constantly less than 1.0 for both TSP and PM0.1, indicating that land transportation is the main emission source. A principal component analysis (PCA) revealed that road transportation, industry, and biomass burning are the key sources of these particles. However, PM arising from Indonesian peatland fires causes an increase in the carbon and trace element concentrations in southern Thailand. The findings make useful information for air quality management and strategies for controlling this problem, based on a source apportionment analysis.

The subtropical forest soil plays a pivotal role in terrestrial carbon (C) cycling. Although global warming is expected to influence subtropical soil C cycling, a consensus on its impact on soil C dynamics remains elusive. Given the significant response of soil microbial respiration to temperature in subtropical soils, understanding its behavior under varying temperature regimes is critical for predicting soil organic C (SOC) responses to climate warming. We conducted a short-term laboratory soil warming incubation experiment, sampling both warmed and un-warmed soils from a subtropical plantation in southeastern China, incubating them at 20 °C, 30 °C, and 40 °C. Our aim was to study the SOC mineralization response to increasing temperatures. Our findings revealed that the temperature sensitivity (Q10) of SOC mineralization to short-term experimental warming varied between the warmed soil and the un-warmed soil. The Q10 of the un-warmed soil escalated with the temperature treatment (20-30 ℃: 1.31, 30-40℃: 1.63). Conversely, the Q10 of the warmed soil decreased (20-30 ℃:1.57, 30-40 ℃:1.41). Increasing temperature treatments enhanced hydrolytic enzyme activity but decreased soil substrate availability in both un-warmed and warmed soil. The Q10 of un-warmed soil was positively correlated with the response ratio of DOC. Additionally, soil microbial biomass exhibited a significant decline, leading to a reduced total amount of PLFAs and a decreased abundance of bacteria, fungi, and Gram-negative bacteria (GN). The changes in temperature also considerably altered the composition of the warmed soil microbial community. A drop in the microbial quotient coupled with a rise in the metabolic quotient indicated that warming amplified microbial respiration over microbial growth. The differential Q10 of SOC mineralization, in response to temperature across varying soil, can largely be attributed to shifts in soil nutrients, C-degrading enzyme activities, and microbial communities (the ratio of fungal to bacterial PLFAs).

Living walls (LWs) are a climate change adaptation strategy for cities, as they have a cooling effect. Previous studies of the cooling effect of LWs were carried out in different climatic zones. These studies differed in their experimental design, or simulated data via models. Plants’ cooling capacity is explained by shading and transpiration, and depends on physical plant parameters, environmental factors, and system-related influences. A three-year-long trial was carried out between 2017 and 2019 at an experimental garden in Geisenheim, Germany. We chose a textile-based LW system with high water demand and plants from a wet/fresh habitat. We assumed that this would achieve high evaporative cooling. The experimental setup included four experimental walls which were exposed to the north, south, east, and west, respectively. The plant choice was divided into three plant mix variants (Cascade, Ground cover, and Meadow) and a Control with no vegetation. We measured the temperature with sensors and a thermal imaging (IR) camera in different setups. The main results were that the measured vegetation temperature (TV) depends on air temperature (TA), measurement position, plant mix variant, and plant species. We could detect the cooling effect only at a small distance from the LW (microclimatic). Our methodological approaches should be continued in further studies.

Silicone rubber formulations in the form of thin discs have been studied under room ambient conditions for their surface characteristics. The samples were silicone rubber manufactured in laboratory and those industrially manufactured. The measurements were done using an electrometer high resistance meter, applying dc voltage under normal room ambient conditions. The results show that the silicone rubber samples show higher values of surface resistivity when the dc voltage was applied. Silicone rubber samples manufactured in laboratory seem to exhibit erratic behaviour unlike their corresponding silicone rubbers manufactured in industry; this could be due to manufacturing shortcomings in laboratory and the irregularities in the way the silicone rubber adhered to the concentric ring electrodes. The empirical current traversing the surface of the silicone rubbers does not decay exponentially but rather it decays as an exponential power of the energization time.

Saprotrophic fungi are key in global carbon cycling, capable of decomposing lignocellulose in wood. This study, for the first time, explores the influence of oxygen (O2) and temperature on methane (CH4) production by two fungi, Laetiporus sulphureus and Pleurotus sapidus. We examined CH4 formation under varying O2 levels (0 to 98%) and temperatures (17, 27, and 40 °C) when the fungi grew on pine wood, beech wood, and grass under sterile conditions. Our findings reveal a strong dependency of fungal CH4 production on O2 mixing ratios. Methane formation was highest when O2 levels exceeded 5%, whilst no CH4 formation was observed after complete O2 consumption by the fungi. Reintroducing O2 immediately resumed fungal CH4 production. When CH4 formation was normalized to O2 consumption (CH4_norm) a different pattern between species was observed. L. sulphureus showed higher CH4_norm rates with higher O2 levels, whereas P. sapidus showed elevated rates between 0-5% O2. Temperature also significantly influenced CH4 and CH4_norm rates, with the highest production at 27 °C, and comparatively lower rates at 17 and 40 °C. These results demonstrate that O2 levels and temperature are critical in controlling fungal CH4 emissions, a consideration necessary for future CH4 source predictions.

AgW materials exhibit excellent properties and are widely used as contact materials in low- and medium-voltage switches. In this study, a pre-sintering and infiltration method was employed to pre-sinter W powder with Cu, Ni, and (Cu+Ni) addition in the low temperature range of 950–1050 °C. The low-temperature sintering behaviours of W skeletons with different additives were investigated. Subsequently, AgW70, AgW75, AgW80, and AgW85 materials were prepared through infiltration at 1050 °C. The microstructure morphology and physical properties of high-W contact materials were investigated using a metallographic microscope and scanning electron microscope. The mechanism of low-temperature sintering-infiltration of high-W contact materials was elucidated. The results indicated that pure W and 1% Cu-added W skeletons experience minimal linear shrinkage within the temperature range of 950–1050 °C. The linear shrinkage curves of W skeletons with different additives coincided under the conditions of 950–1000 °C/90 min. At 1050 °C, after sintering for 150 min, the particle boundaries in the W skeleton were fully spheroidised, with a dihedral angle of 120°. At 1050 °C and after 150 min of infiltration, cross-sectional micrographs of the AgW material revealed the presence of irregular Ni layers, where Ni spatially enveloped/encapsulated Ag. With an increase in the W content, the electrical conductivity and relative density of AgW(70–85) materials decreased, whereas the hardness of the materials increased.

ZnO was synthesized by Sol gel method using zinc nitrate as precursor at different calcination temperatures. Nucleation of ZnO crystallites and their growth with rise in temperature was observed. Exciton bands and lattice imperfections affected the absorption spectra. The decrease in band gap with temperature was due to the formation of defect energy levels. Phonon assisted non-radiative transitions caused broadening of the peaks. The possibility of tuning the band gap of ZnO by changing the temperature was explored. Simulation studies showed transition to single phase with rise in temperature.

We describe electron temperature measurements in the SSX MHD wind tunnel using two different methods. First, we estimate T_e along a chord by measuring the ratio of the C__III 97.7 nm to C_IV 155 nm line intensities using a vacuum ultraviolet monochrometer. Second, we record a biasing scan to a double Langmuir probe to obtain a local measurement of T_e. The aim of these studies is to increase the Taylor state lifetime, primarily by increasing the electron temperature. Also, a model is proposed to predict magnetic lifetime of relaxed states and is found of predict the lifetime satisfactorily. Furthermore, we find that proton cooling can be explained by equilibration with the electrons.

Various theoretical studies have shown that highly diluted plutonium solutions could have a positive temperature effect, but up to now, no experimental program has confirmed this effect. The French Plutonium Temperature Effect Experimental Program (or PU+ in short) aims to effectively show that such a positive temperature effect exists for diluted plutonium solutions. The PU+ experiments were conducted in the “Apparatus B” facility at the CEA VALDUC research center in France. It involved several sub-critical approach type experiments using plutonium nitrate solutions with concentrations of 14.3, 15, and 20 g/l at temperatures ranging from 20 to 40 °C. Fourteen (five at 20 g/l, four at 15 g/l, and five at 14.3 g/l) phase-I experiments (consisting in independent subcritical approaches) were performed between 2006 and 2007. The impact of the uncertainties on solution acidity and plutonium concentration made it difficult to demonstrate the positive temperature effect, requiring an additional phase-II experiment (with a unique plutonium solution) from 22 to 28 °C, that were performed in July 2007. This phase-II experiment has shown the existence of a positive temperature effect of ~ +2.2 pcm/°C (from 22 to 28 °C for a plutonium concentration of 14.3 g/l). It has been recently possible to confirm the results of this program with MORET 5 calculations by generating thermal scattering data S(α,β) at the correct experimental temperatures.

A drinking strategy aiming to replace a given percentage of the sweat losses incurred during exercise should result in reproducible fluid intake volume and, hence, fluid balance from one exercise session to the other performed under similar scenarios. Whether this may also be the case with ad libitum drinking during exercise is unclear. We characterized the repeatability of ad libitum fluid intake during repeated 1 h exercise sessions and examine its effect over time on fluid balance and selected physiological functions and perceptual sensations. Twelve (3 women) healthy individuals participated in this study. At weekly intervals, they completed 4, 2 x 30 min walking/jogging exercise bouts (55% VO2max, 40°C, 20-30% relative humidity) interspersed by a 3 min recovery period. During exercise, participants replaced water (20°C) ad libitum. There were no significant differences among the 4 exercise sessions for absolute fluid intake volume (~ 1000 mL · h-1), percent body mass loss (~ 0.4%), sweat rate (~ 1300 mL · h-1) and percent of sweat loss replaced by fluid intake (~ 80%). Heart rate, rectal temperature and perceived thirst and heat stress did not differ significantly between the first and fourth exercise session. Perceived exertion was significantly lower during the fourth vs. the first exercise session, but the difference was trivial, < 1 arbitrary unit. In conclusion, ad libitum fluid intake during 4 successive identical 1 h walking/jogging sessions conducted in the heat will result in similar fluid intake volumes and perturbations in fluid balance, heart rate, rectal temperature and perceived thirst, heat stress and exertion.

Abstract: An Al-Co-Y diffusion coating was prepared on a TiAl alloy by pack cementation process at a low temperature range of 650-720 ℃. The influence of different activators and co-deposition temperatures on the coating’s microstructure and formation process, and high temperature oxida-tion performance was studied. The results showed that NaF was a more suitable activator for preparing the Al-Co-Y diffusion coating on TiAl alloy compared to NH4Cl and AlCl3. A more compact coating structure can be obtained when deposition was performed at 680 ℃ using NaF as the activator. The coating was mainly composed of a TiAl3 outer layer, a TiAl2 inner layer, and a thin Al-rich TiAl inter-diffusion layer. The growth of the coating exhibited a positive linear correlation between coating thickness increase and the square root of deposition time. The high-temperature oxidation tests showed that a dense scale mainly composed of Al2O3 and a small amount of TiO2 formed on the coating after oxidation at 950 ℃ for 100 h. The scale possessed excellent high-temperature oxidation resistance, with a parabolic rate constant of the oxidation weight gain approximately 4.9×10-3 mg2/cm4 h, which is lower than that of the TiAl substrate by about three orders of magnitude, and lower than that of the pure Al diffusion coating more than one order of magnitude.

In this short communication, a concept has been presented to model geographical data to predict future temperature of Tabuk, region. Machine learning has been applied to the weather station data to develop a prediction model. The preliminary results are promising and encouraging and are envisaging to further this research towards the determination of unknown temperature rise in the region. This is important to mention here, that the problem has been formulated as a Regression problem, NOT as a classification problem. Hence, applying Convolutional neural networks is not possible, due to the non-existence of classes or converting the temperature values to classes does not make any sense. Hence, this is defined as a regression problem which achieved encouraging desirable results.

In the investment casting process, the pattern made of wax is obtained in a die for further formation of shell mold. This work investigates commercial pattern waxes fluidity with a newly developed injection fluidity test. A good correlation between wax fluidity and its viscosity is observed, which is different from metallic alloys, where the solidification behavior is more critical. The difference in investigated filled waxes fluidity can be associated with the type and amount of filler.

Surface temperature influences human health directly and alters the biodiversity and productivity of the environment. While previous research has identified that the composition of urban landscapes influences the physical properties of the environment such as surface temperature, a generalizable and flexible framework is needed that can be used to compare cities across time and space. This study employs the Structure of Urban Landscapes (STURLA) classification combined with remote sensing of New York City’s (NYC) surface temperature. These are then linked using machine learning and statistical modeling to identify how greenspace and the built environment influence urban surface temperature. It was observed that areas with urban units composed of largely the built environment hosted the hottest temperatures while those with vegetation and water were coolest. Likewise, this is reinforced by borough-level spatial differences in both urban structure and heat. Comparison of these relationships over the period between2008 and 2017 identified changes in surface temperature that are likely due to the changes in prevalence in water, lowrise buildings, and pavement across the city. This research reinforces how human alteration of the environment changes ecosystem function and offers units of analysis that can be used for research and urban planning.

: This paper presents a couple of meal monitoring systems for senile dementia patients by using electronic weight and temperature sensors. These monitoring systems enable to convey the information of the amount of meal taken by the patients in real-time via wireless communication networks onto the mobile phones of their families or nurses in charge. Thereby, the nurses can easily spot the most desperate patient to take care of while the families can have relief to see the crucial information for survival of their parents at least three times a day. Meanwhile, the senile dementia patients tend to suffer the burn of their tongues because they can hardly recognize the temperature of hot meals served and therefore avoid the burn of tongues. This phenomenon can be discarded by utilizing the meal temperature monitoring system which displays alarm to the patients when the meal temperature is above the reference. These meal monitoring systems can be easily implemented by utilizing low-cost sensor chips and Arduino UNO boards so that elder-care hospitals and nursing homes can afford to exploit them with no additional cost. Hence, we believe that the proposed monitoring systems would be a potential solution to provide a great help and relief not only for the professional nursing nurses working in elder-care hospitals and nursing homes, but also for the families of the dementia patients.

Recent observations of the dark energy density have demonstrated the fine-tuning problem, and the challenges faced by theoretical modeling. In this study, we apply the self-similar symmetry (SSS) model, describing the hierarchical structure of the universe based on the Dirac large numbers hypothesis, to Einstein's cosmological term. We introduce a new similarity dimension, D_B, in the SSS model. Using the D_B SSS model, the cosmological constant Λ is simply expressed as a function of the cosmic microwave background (CMB) temperature. The result shows that both the gravitational constant G and Λ are coupled with the CMB temperature, which simplifies the solution of Einstein's field equations for the variable Λ-G model.

This work presents the computation of reliable warming trends for central Australia around Alice Springs within a circle of radius 1,000 km. Between 1880 and 2011, the average warming for the centre of Australia is +0.166 ºC/century, slightly smaller than the warming of Alice Springs, that is +0.176 ºC/century. Over a shorter time between 1910 and 2011, the centre of Australia is warming +0.794 ºC/century, slightly more than the warming of Alice Springs, that is +0.719 ºC/century.

The physical and mechanical properties of rocks will change significantly after being subjected to high temperatures, which poses safety hazards to underground projects such as coal underground gasification. In order to investigate the effect of temperature on the macroscopic and microscopic properties of rocks, this paper has taken sandstone as the research object and conducted uniaxial compression tests on sandstone specimens at different temperatures (20-1000 ℃) and different heating rates (5-30 ℃/min) at 1200 ℃. At the same time, the acoustic emission (AE) test system was used to observe the acoustic emission characteristics of the rock damage process, and the microstructural changes after high temperature were analyzed with the help of a scanning electron microscope (SEM). The test results show that the effect of temperature on sandstone is mainly divided into three stages: Ⅰ (20-500 ℃) stage is the strengthening zone, the evaporation of water and the contraction of primary fissures, sandstone densification is enhanced. Specifically, the compressive strength and elastic modulus increase, the macroscopic damage mode is dominated by shear damage, and the fracture micro-morphology is mainly brittle fracture. Stage II (500-600°C) is the transition zone, 500°C is the threshold temperature for compressive strength and modulus of elasticity, and the damage mode changes from shear to cleavage damage, and the sandstone undergoes brittle-ductile transition in this temperature interval. Stage III is the physicochemical deterioration stage. The changes in physical and chemical properties make the sandstone compressive strength and modulus of elasticity continue to decline, the macroscopic damage mode is mainly dominated by cleavage damage, and the fracture microscopic morphology is more toughness fracture. The effect of different heating rates on the mechanical properties of sandstone was further studied, and it was found that the mechanical properties of the rock were more deteriorated under higher heating rates.