It is known that ammonium has a higher permeability through anion-exchange and bipolar membranes compared to K+ cation that has the same mobility in water. However, the mechanism of this high permeability is not clear enough. We develop a mathematical model based of the Nernst-Planck and Poisson equations for diffusion of ammonium chloride through an anion-exchange membrane; proton exchange reactions between ammonium, water and ammonia are taken into account. It is assumed that ammonium, chloride and OH− ions can only pass through membrane hydrophilic pores, while ammonia can also dissolve in membrane matrix fragments not containing water and diffuse through these fragments. It is found that due to the Donnan exclusion of H+ ions as coions, the pH in the membrane internal solution increases when approaching the membrane side facing distilled water. Consequently, there is a change in the principal nitrogen-atom carrier in the membrane: in the part close to the side facing the feed NH4Cl solution (pH<8.8), it is the NH4+ cation, and in the part close to distilled water, NH3 molecules. The concentration of NH4+ reaches almost zero at a point close to the middle of the membrane cross-section, which approximately halves the effective thickness of the diffusion layer for the transport of this ion. When NH3 takes over the nitrogen transport, it only needs to pass through the other half of the membrane. Leaving the membrane, it captures an H+ ion from water, and the released OH− goes towards the membrane side facing the feed solution to meet the NH4+ ions. The comparison of the simulation with experiment shows a satisfactory agreement.

The research on calcium leaching of 3D printed cement pastes (3DPC) exposed in aggressive water is limited, and the mechanism underlying its effect needs to be better understood. The performance anisotropy of degraded 3DPC due to calcium leaching is investigated in this paper. Samples with aggregate micro fines (AMF) and fly ash (FA) were prepared. A 6 mol/L NH₄Cl solution was used in the accelerated experiment. At specific leaching durations, performances were tested on the samples in different leaching directions. Results show that the performances of 3DPC in aggressive water have a significant anisotropic behavior. The evolution of pore defects and hydration products mainly governs the performance anisotropy of degraded 3DPC. The remaining hydration products of the surface of 3DPC leached in the Z direction are less than the other two directions because calcium ions leached in the Z direction are difficult to be compensated through weak interfaces between layers.

In this research, a novel collector cetyl trimethyl ammonium chloride (CTAC) was used to separate hematite from quartz via reverse flotation for the first time. Micro-flotation tests showed that CTAC had a strong ability to selectively collect quartz and a separation of hematite from quartz could be accomplished with a concentration of 0.00263 mmol/L CTAC. Zeta-potential measurements indicated that the positive CTAC+ species could selectively increase the surface potential of quartz, but it had rather a weak effect on the hematite surface. X-ray photoelectron spectroscopy (XPS) detection indicated that CTAC had a stronger binding affinity to oxygen sites on the surface of quartz than that of hematite, resulting in a large amount of CTAC predominantly adsorbed on quartz rather than hematite.

Ammonium sulfate has been utilized in agriculture; however, there is a dearth of research on its application in maize cultivation subsequent to the implementation of nitrification inhibitors or coating. This study aims to analyze the impacts of various combinations of ammonium sulfate fertilizers on soil nutrients, plant nutrient uptake, yield, and fertilizer utilization efficiency in maize cultivation to ascertain the optimal and stabilized disposal method for ammonium sulfate. A completely randomized design was employed with five treatments (AU, the control using urea; AS, treatment using ammonium sulfate; ASN, treatment using ammonium sulfate with a nitrification inhibitor; ASG, treatment using oil-coated ammonium sulfate; ASD, treatment using oil-humic acid-coated ammonium sulfate). Results showed that: (1) Compared with AU and AS, ASN, ASG and ASD decreased the leaching rates of TN, NH4+-N and NO3-N to the 10-20 cm soil layer, and more residual N was obtained in 0-10 cm soil layer. The first-order kinetic equation Nt=N0(1-e-kt) can better fit the process of nitrogen accumulation and release, and the N release rate constant is AU>CK>AS>ASH>ASN>ASD; (2) Compared with AU and AS treatments, the plant dry weight, grain dry weight, spike width, spike length, and yields of maize increased by 8.85-11.08%, 12.98-14.15%, 2.95-3.52%, 5.50-5.65%, and 43.21-51.10% under ASG treatment respectively. The impact of effective spike number on maize yield was found to be significant, as demonstrated by the path analysis conducted in this study. Furthermore, the accumulation levels of nitrogen, phosphorus, and potassium within above-ground plants significantly increased under the ASG treatment compared to the AU and AS treatments. The partial productivity of nitrogen, phosphorus, and potassium increased by 1.43-1.51-fold under ASG treatment, while grain nitrogen balance, grain phosphorus balance, and grain potassium balance increased by 1.41-1.58-fold, 1.51-1.95-fold, and 1.15-l.96-fold respectively. The oil-coated ammonium sulfate, therefore, exhibited the optimal slow-release effect of nutrients, thereby achieving superior performance in enhancing maize production and efficiency.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

Sewage sludge was utilized into biochar using the slow pyrolysis method. The biochar was then being used for ammonium removal. The sewage sludge biochar was produced at temperature of 550°C, 600°C, 650°C, 700°C and 750°C. A few characterization tests were carried out to study about the physical and chemical properties of the biochar. For instance, moisture and ash content analysis, FTIR spectroscopy, pH Zero Point Charge, biochar yield and SEM. As the pyrolysis temperature increased, the moisture content of SSB decreased while the ash content increased. The FTIR spectra of sewage sludge biochar showed that there were various organic functional groups on the surface of the biochar which were responsible for ammonium adsorption. Furthermore, through pH Zero Point Charge analysis, pH 7.0 was the most optimum pH for the adsorption test of ammonium. The optimum adsorbent dosage was 0.01g while optimum contact time was 150 minutes. Furthermore, 1.2ppm was the most optimum concentration for adsorption process. Based on the result of the characterization tests, SSB700 was the most effective biochar for ammonium adsorption. Based on the result of kinetic and isotherm analysis, the adsorption of ammonium ions usign sewage sludge biochar was a monolayer chemisorption process.

Bare titania and metal promoted TiO2 catalysts were employed in the treatment of nitrates, which are ubiquitous pollutants of wastewater. The results show that the process can be carried out under visible light (from white light LED lamp) and, in the best case, 23.5% conversion of nitrate was obtained over 4 hours with full selectivity towards N2 by employing 0.1 mol% Ag/TiO2 prepared by flame spray pyrolysis. Moreover, the performance was worse when testing the same catalysts with tap water (11.3% conversion), due to the more complex composition of the matrix. At last, it was found that the photoreduction of nitrate can be effectively performed in combina-tion with the photo-oxidation of ammonium without loss in the activity, opening to the possi-bility to treat highly polluted wastewater with a single process. The latter treatment employs the two contaminants simultaneously as electron and holes scavengers, with very good selectiv-ity, in a completely new process that we may call Photo-Selective Catalytic Reduction (Pho-to-SCR).

Nanoporous membranes promise energy-efficient water desalination. Hexagonal boron nitride (h-BN), like graphene, exhibits outstanding physical and chemical properties, making it a promising candidate for water treatment. We employed Car–Parrinello molecular dynamics simulations to establish accurate modeling of Na+ and Cl- permeation through hydrogen passivated nanopores in graphene and h-BN membranes. In these complex systems the classical potentials cannot properly account for the physics at play. We demonstrate that ion separation works well for the h-BN by imposing a barrier of 0.13 eV and 0.24 eV for Na+ and Cl- permeation respectively, compared to the graphene where the Cl- ion faces a negative barrier of 0.68 eV and is prone toward blockade and Na+ permeation is associated with a slightly negative barrier of 0.03 eV. From the change in the solvation shell, we get the following trend: Na/h-BN > Na/G > Cl/G > Cl/h-BN. We argue that the trend in the permeation barrier changes to Cl-h-BN > Na-h-BN > Na-G > Cl-G due to a combination of several interactions, including the distortion of the water network induced by the ions, the ion-water interaction, and the ion-nanopore interaction. Overall, the desalination performance of h-BN surpasses that of their graphene counterparts.

A good optical quality crystal of 2-aminopyridine (2AP) metal complex crystals was grown by slow evaporation technique at room temperature. The transparent and defect less bulk size of 2-aminopyridine potassium dihydrogen orthophosphate metal complex crystals have been grown by solution growth method. The molecular structure and morphology of grown crystals was drawn and planes are indexed using WINXMORPH software. A optical absorption spectrum, the UV cut-off wavelength, Band gap (Eg), Reflectance (R), Refractive Index (n), Extinction coefficient (K) and Electrical susceptibility (χc) are calculated for 2AP metal complex crystals.

Nitrogen (N) strongly affects plant growth and metabolism. For shikonin biosynthesis, although the ammonium toxicity phenomenon has been reported, the effects of nitrogen on the shikonin synthesis remains obscure. In this study, we carried out four different concentrations of NH4+ treatments on Arnebia euchroma hairy roots (AEHR) to clarify the influence of NH4+ on the growth and shikonin accumulation in A. euchroma and the possible mechanism. The results showed that compared with the 0% NH4+ treatment (only nitrate as nitrogen source), 10% NH4+ treatment increased the fresh weight and the dry weight of AEHR, and promoted the synthesis of shikonins; 20% NH4+ treatment started to show the inhibition effects on growth and shikonin accumulation of AEHR and 30% NH4+ treatment exhibited the strongest inhibition effects. With increased percentage of NH4+, AEHRs became shorter and thicker with more branches. To further elucidate the mechanism, we analyzed the time-course of nitrogen assimilation, gene expression level of key enzymes involved in the shikonin biosynthesis pathway, and contents of various endogenous hormones under NH4+ toxicity condition. Results indicated that auxin and cytokinin might regulate the growth and architecture of AEHR under NH4+ toxicity, and jasmonate level was reduced along with the inhibition of shikonin biosynthesis. This first comprehensive investigation into the effects of ammonium/nitrate ratio on shikonin biosynthesis not only provided valuable data for optimizing the in vitro culture and shikonin production in A. euchroma, but also suggested potential fertilizer strategies for its cultivation.

The corrosion inhibition behavior of cetyl pyridinium chloride (CPC) on mild steel (MS) in 0.5 M H₂SO₄ solution was examined using the weight loss method and potentiodynamic polarization method. The experimented MS surface was characterized by Fourier Transform Infrared Spectroscopy (FTIR), Field Emission Scanning Electron Microscopy (FESEM), and Atomic Force Microscopy (AFM). Corrosion rate and corrosion efficiency was calsulated via weight loss and potentiodynamic polarization methods where the corrosion rate in 0.5 M H₂SO₄ , 0.000192 M, and 0.0077 M of CPC solution was 12.09×10^-3, 8.23×10^-3, 6.63×10^-5 (mm/Year), respectively and the inhibition efficiency of 94.42% and 98.54%. FESEM studies demonstrated the corrosion attack on MS surface. Also, the EDX showed the presence of nitrogen of CPC. Thus, CPC acts as an important corrosion inhibitor.

With the current increase in the demand from animal and agricultural products, management of agrowaste has become critical to avoid greenhouse gas emissions. The present article investigates the applicability of ammonium bicarbonate synthesis via flash distillation to valorize and stabilize several types of anaerobic digestate produced from individual fermentations of amino acids. Prior to the development of the model in Aspen Plus v12, the description of the system aqua-ammonia-carbon dioxide provided by the electrolyte non-random two-liquid property method was validated with empirical data available in the literature. The content of CO₂ in the digestate was found to be responsible of the OH alkalinity (0.4 equivalents of acid/kg digestate), while the partial and total alkalinities (0.8 eq/kg digestate) were essentially derived from the content of NH₃. The most suitable conditions for the flash distillation were 95 ⁰C and 1 bar with the condensation occurring at 25 ⁰C. However, in order to attain the precipitation of NH₄HCO₃ in the distillate, it was necessary to consider digestates with a moisture content of 50 wt.%, since the minimum levels of inorganic nitrogen and inorganic carbon were not attained otherwise. Even under these conditions, few amino acids (i.e. arginine, glycine, and histidine) were able to provide an anaerobic digestate, upon fermentation, that would be suitable for NH₄HCO₃ stabilization. Despite alanine digestate and glutamine digestate presented sufficient concentrations of inorganic nitrogen and inorganic carbon, the NH₄HCO₃-stabilization was not feasible due to the limited volatilization of NH₃. The process of stabilization with a capacity of a tonne of digestate per hour was improved by adding hydrochloric acid or sodium hydroxide at rates 44 kg/h, leading to production of 34 kg NH₄HCO₃/h. The economic viability of this process needs to be investigated considering not only the market value of the isolated inorganic fertilizer but the carbon credits saved, resulting from handling a more stabilized organic manure. Furthermore, given the role of the volatile elements of the biogas as endogenous stripping agents, it is recommended to use a fresh and saturated digestate as feed for the flash distillation.

Hydrothermal carbonization of cellulose was examined at 240 ℃ for 1 h. Ammonium sulfate and thiourea were selected as the doping sources of inorganic nitrogen and organic nitrogen for the preparation of supercapacitor carbon. The effect of boric acid on the properties of the resulting hydrochar after KOH activation was examined. The results showed that the proportion of functional groups and the specific surface area of the activated hydrochar would be reduced after the addition of boric acid, and the pore-forming process of the micropores would be inhibited. The hydrochar obtained from the reaction of cellulose and organic nitrogen compounds had better pore size distribution and electrochemical properties after activation. The largest specific surface area (952.27 m2 g-1) was obtained when only thiourea was used as the only doping source. In the three-electrode system, the specific capacitance resulting activated hydrochar reached 236.25 F g-1 at a current density of 1 A g-1. After 20,000 cycles of charging and discharging at a current density of 10 A g-1, the capacitance retention rate reached 99.96%. Therefore, this study proves that the supercapacitor carbon with good electrochemical properties could be obtained by the direct reaction of cellulose with organic nitrogen compounds.

A sensitive and robust electrochemical cholinesterase-based sensor was developed to detect the quaternary ammonium (QAs) biocides most frequently found in agri-food industry wash waters: benzalkonium chloride (BAC) and didecyldimethylamonium chloride (DDAC). To reach the maximum residue limit of 2.8 10-8 M imposed by the European Union (EU), two types of cholinesterases were tested, acetylcholinesterase (AChE, from Drosophila melanogaster) and butyrylcholinesterase (BChE, from horse serum). The sensors were designed by entrapping AChE or BChE on cobalt-phthalocyanine-modified screen-printed carbon electrodes. The limits of detection (LOD) of the resulting biosensors were 3.8 10-8 M for DDAC and 3.2 10-7 M for BAC, using respectively AChE and BChE. A simple solid phase extraction step was used to concentrate the samples before biosensor analysis, allowing the accurate determination of DDAC and BAC in tap water with limits of quantification (LOQ) as low as 1.3 10-9 M and 5.3 10-9 M, respectively. The biosensor was shown to be stable during 3-months storage at 4°C.

Arsenic, an element of environmental impact, can be incorporated into jarosite–type compounds and remain stabilised within the structure under a wide range of environmental conditions. In this study, a sample of ammonium–arsenic jarosite was synthesised by precipitation in sulphate medium at controlled pH of 1.2–1.8. The behaviour of arsenic during the thermal and chemical decomposition of jarosite was analysed; the degradation in alkaline medium of jarosite was also studied. According to the results, the synthesised jarosite is composed of joined rhombohedral crystals, forming tightly spherical shaped particles, 37–54 μm size. The ammonium jarosite produced possessed a high arsenic concentration; its calculated stoichiometry being (NH₄)Fe_2.45[(SO₄)_1.80(AsO₄)_0.20][(OH)_4.15(H₂0)_1.85]. It was found that arsenic is stabilised in the jarosite structure; upon heating, it remains in residual solids above 700°C, whilst in alkaline medium an incongruent dissolution takes place, with the arsenic retained in the solid phase along with iron. These solids, when exposed to high temperatures (1200°C), transform into a type of iron oxide known as hematite, so with arsenic it is retained an iron compound forming a stable compound which withstands high temperatures.

Since electrical resistivity of concrete can be measured in a more rapid and simple way than chloride diffusivity, it should be primarily regular quality control of the electrical resistivity of concrete which provides the basis for indirect of quality control of concrete durability during the concrete construction. If this is realized, the electrical resistivity of concrete can be a crucial parameter to establish maintenance strategy for marine concrete structures. Electrical resistivity of concrete is important to estimate two processes involved in corrosion of reinforcement: initiation (chloride penetration) and propagation (corrosion rate). The resistivity of concrete structure exposed to chloride indicates the risk of early corrosion damage, because a low resistivity is related to rapid chloride penetration and to high corrosion rate. Concrete resistivity is a geometry-independent material property that describes the electrical resistance, which is the ratio between applied voltage and resulting current in a unit cell. The current is carried by ions dissolved in the pore liquid. While some data exist on the relationship between moisture content on electrical resistivity of concrete, very little research has been conducted to evaluate the effect of chloride on the conduction of electricity through concrete. The purpose of this study is to examine and quantify the effect of pore water and chloride content on surface electrical resistivity measurement of concrete. It was obvious that chloride content had influenced the resistivity of concrete and the relationship showed a linear function. That is, concrete with chloride ions had a comparatively lower resistivity. Chloride can lead to underestimate the electrical resistivity of concrete. Conclusively, this paper suggested the quantitative solution to depict the electrical resistivity of concrete with various chloride contents.

In this study, literature on pore structure and chloride ion diffusivity was collected to investigate the correlation of pore structure indicators with diffusivity. Good correlation between total porosity and chloride ion diffusivity was found when the samples did not contain admixture materials and diffusion test was conducted without acceleration. Pore diameter indicators did not correlate with diffusivity. The diffusivity of cement paste was reduced by admixture materials compared to that without admixture materials even if the total porosity is the same. On the other hand, the diffusivity of concrete was not reduced by admixture materials.

Repair mortar is commonly used to rehabilitate reinforced concrete structures or components that exhibit a relatively high level of distresses. Yet, this repair mortar can be contaminated by salt from its service environment. This work employs a two-dimensional finite element model to investigate the transport behavior of ionic species in salt-contaminated and water-saturated repair mortar under an externally applied electric field. The model was experimentally validated and then utilized to evaluate the effectiveness of electrochemical chloride extraction (ECE) with or without electrical injection of corrosion inhibitor (EICI). In the case study, both the ECE alone and the ECE+EICI treatment was found effective in decontaminating the zone in front of the steel rebar. In both techniques, the magnitude of current density has a significant effect on removing chloride out of the mortar and increasing the pH of the pore solution near the rebar, whereas the treatment time any not have a significant effect under some scenarios. The injection of the organic corrosion inhibitor significantly slowed down the removal of chloride. Changes in the ionic distribution in the mortar were generally beneficial in reducing the corrosion risk of the steel rebar and thus extending the service life of the repair mortar.

Elevated ammonium (NH4+) concentrations in untreated waterways contribute to eutrophication and dissolved oxygen depletion, which cause severe degradation of water quality. Ion exchange processes are a robust, low operational cost and efficient option for ammonium removal with zeolites being the most widely used. Geopolymers are a sustainable and low-cost option compared to zeolites that follows the same ion exchange technology. In the present study, a metakaolin-based porous geopolymer was synthetized, characterised and validated as adsorbent material. The laboratory batch tests showed a maximum adsorption capacity (Qm) of 18.35 mg/g being 27% higher than reference zeolites. Kinetics followed the Weber-Morris rate equation being the intraparticle diffusion the limiting process and continuous experiments indicated a maximum removal of 97% in the first hours. The material was validated in a wastewater treatment pilot plant where values in pH, electrical conductivity and NH4+ concentration were monitored. The obtained data indicated that the material achieved up to 80% NH4+ removal which is similar to traditional zeolites. The results demonstrate that this sustainable, low-cost and easy-to-install metakaolin-based geopolymer can be used effectively for NH4+ treatment.

As a hazardous waste, pickling waste liquor must be properly treated. An alternative consists in promoting the formation of ferrous salts from this residue, due to its higher ferrous content. Since FeCl2·4H2O is widely used in several applications, obtaining pure crystals of this material appears to be an interesting prospect. However, this compound has scarcely been investigated. In the present work, FeCl2·4H2O crystals have been obtained from pickling waste liquors. Their structural and morphological characteristics have been investigated by X-ray diffraction, scanning electron microscopy as well as Mössbauer spectroscopy. In addition, the photoluminescence study of the obtained samples was also assessed. It was observed that after some aging time, the obtained crystals change in colour from green to more yellowish. So, the aged sample has also been evaluated, and their structural characteristics are compared with the original crystals. Despite this, the obtained crystals exhibit a FeCl2·4H2O structure, which is not modified with the aging of the sample.

Chloride (Cl-) is applied in coffee in rates as a “macronutrient” due that potassium (K+) is one of the most demanded nutrients by the coffee plant, and the potassium muriate (KCl) bases fertilizer is one the most used by the coffee growers. Does not exist scientific evidence that addresses the question regarding with which is the influences of the Cl- applied in the K fertilization base on MOP on coffee growth, nutrient uptake, and nitrogen use efficiency (NUE). Over four years, two trials were conducted on greenhouse and field conditions to address these questions. The trials set up were designed to test the influence of increased Cl- and reduced S rates on biomass accumulation, nutrient uptake, and NUE. A significant effect of the Cl- rates on growth was observed under greenhouse conditions but a non-significant effect on yield under field conditions. Cl- and S significantly influence the NUE in coffee. The result allows us to conclude that Cl- rates need to be balanced with S rates and that Cl- applied as a macronutrient can improve the NUE in coffee when those rates do not exceed 180 mg. L-1 Cl- and 80 mg.L-1 S in the greenhouse and 150 kg.ha-1.year-1 Cl- and 50 kg. ha-1.year-1 S in field conditions. In practical terms, coffee farmers need to balance the K base fertilizers sources to improve the nutrient use efficiency, especially the NUE.

The SLC12 family of cation-chloride-cotransporters (CCCs), comprising potassium chloride cotransporters (KCCs)-mediated Cl- extrusion relative to sodium chloride cotransporters (NKCCs)-mediated Cl- loading, play vital roles in cell volume regulation and ion homeostasis. These functions of the CCCs influence a variety of physiological processes, many of which overlap with the pathophysiology of cardiovascular disease. Although not all of the cotransporters have been linked to Mendelian genetic disorders, recent studies have provided new insights into their functional role in vascular and renal cells along with their contribution to cardiovascular diseases. Particularly, an imbalance in potassium levels promote the pathogenesis of atherosclerosis and disturbances in sodium homeostasis are one of the causes of hypertension. Recent findings even suggest hypothalamic signalling as a key signalling pathway in the pathophysiology of hypertension. In this review, we summarize and discuss the role of CCCs in cardiovascular disease with particular emphasis on knowledge gained in recent years on NKCCs and KCCs.

We report the influence of ammonium hydroxide (NH4OH), as growth additive, on zinc oxide nanomaterial through the optical response obtained by photoluminescence (PL). A low-temperature hydrothermal process is employed for the growth of ZnO nanowires (NWs) on seedless Au surface. A more than two order of magnitude change in ZnO NW density is demonstrated via careful addition of NH4OH in the growth solution. Further, we show by systematic experimental study and PL characterization data that the addition of NH4OH can degrade the optical response of ZnO NWs produced. The increase of growth solution basicity with the addition of NH4OH may slowly degrade the optical response of NWs by slowly etching its surfaces, increasing the point defects in ZnO NWs. The present study demonstrates the importance of growth nutrients to obtain quality controlled density tunable ZnO NWs on seedless conducting substrates.

Polyvinyl chloride (PVC) electric wires were subjected to dechlorination in subcritical water at three different temperatures in a high-pressure reactor. About 2.09, 73.08 and 95.96 wt. % of chlorine in PVC wires was removed during dechlorination at 200, 250 and 300 °C, respectively. The solid residues were analyzed and characterized by thermogravimetry, at three different heating rates (5, 10 and 20 °C/min) in inert and oxidizing atmosphere. With the purpose of studying the emission of chlorinated pollutants, pyrolysis experiments at 850 °C were also performed in a laboratory scale reactor with the dechlorinated materials, as well as with the original PVC electric wire. Polycyclic aromatic hydrocarbons (PAH) formation increased, but chlorobenzenes (ClBz) and chlorophenols (ClPh) formation decreased as the temperature of dechlorination increased; naphthalene was the most abundant PAH and monochlorobenzene and monochlorinated phenols (3-+4-) were the most abundant chlorinated compounds.

Stable half-sandwich iron(II) dihalido complexes of the type [Fe(5-Cp’)X2] are extremely scarce, being limited to congeners containing the bulky C5H2-1,2,4-tBu3 ligand. We have extended this to homologues [Fe(5-Cp*)X2] (X = Cl – I) containing the particularly popular C5Me5 (Cp*) ligand. Corresponding ionic compounds ER4[Fe(5-Cp*)X2] are easily accessible from FeX2, MCp* (M = Li, K) and a suitable halide source R4EX (E = N, P) in THF. The new compounds NnPr4[Fe(5-Cp*)X2] (X = Cl, Br), NnPr4[Fe(5-Cp*)BrCl] and PPh4[Fe(5-Cp*)X2] (X = Cl, Br, I) have been structurally characterised by single-crystal X-ray diffraction. NnPr4[Fe(5-Cp*)Cl2] reacts readily with CO to afford [Fe(5-Cp*)Cl(CO)2], indicating the synthetic potential of ER4[Fe(5-Cp*)X2] in FeCp* half-sandwich chemistry.

The present study concerns the application of electrochemical chloride extraction to concrete designed with partial replacements of Ordinary Portland Cement (OPC) from different binders, namely ground granulated blast furnace (GGBS), pulverized fly ash (PFA) and Silica Fume (SF), to attend the need of corrosion repair for modern constructions. Electrochemical Chloride Extraction (ECE) was applied to the specimens at a current density of 2A/m2 for 4 weeks. The chloride types and binding mechanisms appeared to have important implications on the different performance of treatment perceived for all binders. Considering total chlorides, removal was more significant for OPC and GGBS when compared to others. The main difference noted was that for GGBS the removal of bound chlorides was more significant due to a possible release of adsorbed chlorides from the silicate hydrates, present at higher intensities in this case. However, even though GGBS had greater rates of bound chloride removal it had still the same percentage as OPC for total efficiency due to the fact that in OPC the removal of free chlorides is more expressive.

Biocidal compositions based on interpolyelectrolyte complexes and a low molecular weight antibiotic can become a promising material for creating biocidal coatings, as they combine wash-off resistance and dual biocidal action due to the biocide and the polycation. Molecular mass characteristics of polymers play essential role in physics and mechanical properties of the coatings. In this work, the properties of polydiallyldimethylammonium chloride (PDADMAC) coatings of various molecular weights are investigated and assumptions are made about the optimal molecular weight needed to create antibacterial compositions. To study the resistance to washing off and moisture saturation of the coatings, the gravimetric method was used, the adhesive properties of the coatings were studied by dynamometry. It has been established that an increase in molecular weight affects the wash-off resistance of coatings, but does not affect moisture absorption and adhesion mechanics of coatings. All samples of PDADMAC were demonstrated to exhibit the same antibacterial activity. Thus, when developing systems for creating antibacterial coatings, it must be taken into account that in order to create stable coatings. The requirement to use PDADMAC with a high degree of polymerization is necessary for control the desorption of coating during wash off-but not mandatory for the control of mechanical and antibacterial properties of the coating.

The corrosion morphology in grade 2205 duplex stainless steel wire has been studied to understand the nature of pitting and the causes of the ferrite phase's selective corrosion in acidic NaCl solution. It is shown that the corrosion mechanism is always pitting, which either manifests lacy cover perforation or densely-arrayed selective cavities developing on the ferrite phase. Pits with a lacy metal cover form in concentrated chloride solutions, whereas the ferrite phase's selective corrosion develops in diluted electrolytes, showing dependency on the chloride-ion concentration. The pit perforation is probabilistic and occurs on both austenite and ferrite grains. The lacy metal covers collapse in concentrated solutions but remain intact in diluted electrolytes. The collapse of the lacy metal cover happens due to hydrogen embrittlement. Pit evolution is deterministic and occurs selectively in the ferrite phase in light chloride solutions.

Modified ammonium polyphosphate (MAPP) as a novel mono-component intumescent flame retardant (IFR) was prepared via the ionic exchange between ammonium polyphosphate (APP) and piperazine sulfonate, which is synthesized by self-assembly using 1-(2-Amioethyl) piperazine (AEP) and p-amino benzene sulfonic acid (ASC) as raw materials. This all-in-one IFR integrating three functional elements (carbon, acid, and gas source) showed more efficient flame retardancy and excellent smoke suppression as well as better mechanical properties than the conventional APP. The incorporation of 22.5 wt.% MAPP into polypropylene (PP) eliminated the melt dripping phenomenon and passed the UL-94 V-0 rating. The results of the cone calorimetry test (CCT) revealed that the release of heat, smoke, and CO is significantly decreased, demonstrating that this novel IFR endows PP with excellent fire safety more effectively. For PP/MAPP composites, a possible IFR mechanism was proposed based on the analysis of the pyrolysis gas and char residues.

In this study, the extraction of rare earth elements (REEs) from chloride solutions containing mixtures of these metals with solutions of the mixtures of P507 and Cyanex 272 (1:1) of various concentrations was experimentally studied. It was shown that the distribution coefficients of all REEs decrease with increasing concentration of these metals in the initial solution, which is associated with the loading of the organic phase. The most significant improvement in the extraction is observed for heavy group of rare earth elements. The extractability of REEs enhances with increasing atomic number of the element, as is typical for the extraction of these metals with acidic organophosphorus extractants. The data obtained show that separation factors of adjacent rare earth elements mainly decrease with increasing concentration of metals in the initial aqueous solution. Increasing the concentration of the extractant mixture does not have a significant effect on the values of the adjacent REE separation factors. Analysis of the experimental results shows that two commercial products can be obtained from a concentrate of the medium-heavy group. In the first cascade, yttrium can be separated, in the second, a concentrate of dysprosium and terbium can be obtained.

Salinity substantially affects plant growth and crop productivity worldwide. Plants adopt several biochemical mechanisms including regulation of antioxidant biosynthesis to protect themselves against the toxic effects induced by the stress. One-year-old Pistachio rootstock exhibiting different degrees of salinity tolerance were subjected to sodium chloride induced salt stress to identify genetic diversity among cultivated pistachio rootstock for their antioxidant responses, and to determine the correlation of these enzymes to salinity stress. Leaves and roots were harvested following NaCl-induced stress. Results show that a higher concentration of NaCl treatment induced oxidative stress in the leaf tissue and to a lesser extent in the roots. Both tissues showed an increase in ascorbate peroxidase, superoxide dismutase, catalase, glutathione reductase, peroxidase and malondialdehyde. Responses of antioxidant enzymes were cultivar dependent, as well as temporal and dependent on the salinity level. Linear and quadratic regression model analysis revealed significant correlation of enzyme activities to salinity treatment in both tissues. The variation in salinity tolerance reflected their capabilities in orchestrating antioxidant enzymes at the roots and harmonized across the cell membranes of the leaves. The study provides a better understanding of root and leaf coordination in regulating the antioxidant enzymes to NaCl induced oxidative stress.

PVC-based materials are bad in terms of biodegradability. To enhance the ecological property of such materials, the fabrication of PVC-based composites using biofillers with acceptable performance characteristics could be considered. In this work, plant-filled PVC-based composite materials were obtained and study their optical, structural, thermal, and mechanical properties depending on the nature of the filler (spruce flour, birch flour, and rice husk) were studied. Increasing the proportion of plant filler somewhat reduces the strength characteristics and reduces the flexibility of the samples. But samples with plant filler allows them to be used at low temperatures without changing the operating characteristics. Some of the fillers affected the thermal stability of composites by increasing their thermal decomposition resistance. So, results have shown that plant-filled polymer composites based on PVC can be used on an equal basis with unfilled PVC plastic compound for some applications such as construction.

The service life of the reinforced concrete structure in the marine environment can be impaired significantly due to chloride-induced corrosion. However, how the chloride diffusion in pre-cracked concrete structures is affected by the hydrostatic pressure magnitude is poorly understood. This study experimentally examined the effect of hydrostatic pressure on the chloride diffusion in pre-cracked concrete. Cracks with five different widths, i.e., 20 μm, 40 μm, 60 μm, 80 μm, and 100 μm, were manually created using a splitting tensile apparatus respectively. The chloride diffusion in the concrete with a certain crack was then studied under four different hydrostatic pressures of 0 MPa, 0.1 MPa, 0.3 MPa, and 0.5 MPa. Experimental results show that the chloride diffusion in concrete with a crack greatly relies on both the hydrostatic pressure and the crack width. The chloride concentration increases as the hydrostatic pressure grows, particularly for the wider cracks with width ranging from 60 μm to 100 μm. Surprisingly, the hydrostatic pressure has a negligible effect on the chloride distribution in the concrete with a crack width no larger than 40 μm. Both the chloride diffusion coefficient and the surface chloride concentration of concrete increased gradually as the hydrostatic pressure increased. The experimental findings enrich our understanding of the behavior of pre-cracked concrete when exposed to chloride-induced corrosion at different depths of marine environments.

The paper presents a synthesis of deep eutectic solvents (DESs) based on choline chloride (ChCl) as hydrogen bond acceptor and phenol (Ph), glycol ethylene (EG), and levulinic acid (Lev) as hydrogen bond donors in 1:2 molar ratio. DESs were successfully used as absorption solvents for removal of dimethyl disulfide from (DMDS) from model biogas steam. Several parameters affecting the absorption capacity and absorption rate has been optimized including kind of DES, temperature, the volume of absorbent, model biogas flow rate, and initial concentration of DMDS. Furthermore, reusability and regeneration of DESs by means of adsorption and nitrogen barbotage followed by the mechanism of absorptive desulfurization by means of density functional theory (DFT) as well as FT-IR analysis were investigated. Experimental results indicate that the most promising DES for biogas purification is ChCl:Ph, due to high absorption capacity, relatively long absorption rate, and easy regeneration. The research on the absorption mechanism revealed that van der Waal interaction is the main driving force for DMDS removal from model biogas.

In order to assess the human exposure risks from the release of contaminants from water pipes made of polyvinyl chloride (PVC), experiments were carried out by subjecting the PVC pipe material to burning and leaching conditions followed by analysis of the emission and leachate samples. The emissions of burning pipes were analyzed by both infrared spectrometry and gas chromatography-mass spectrometry (GC-MS). The emission results indicate the presence of chlorinated components including chlorine dioxide, methyl chloride, methylene chloride, allyl chloride, vinyl chloride, ethyl chloride, 1-chlorobutane, tetrachloroethylene, chlorobenzene, and hydrogen chloride were detected in the emissions of burning PVC pipes. Furthermore, the concentrations of benzene, 1,3-butadiene, methyl methacrylate, carbon monoxide, acrolein, and formaldehyde were found at levels capable of affecting human health adversely. The analysis of PVC pipe leachates using GC-MS shows that there are 40-60 tentatively identified compounds, mostly long-chain hydrocarbons such as tetradecane, hexadecane, octadecane, and docosane, were released when the burned PVC materials were soaked in deionized water for one week. Quantitative analysis shows that 2-butoxyethanol, 2-ethyl-1-hexanol, and diethyl phthalate were found in the burned PVC polymer at the average levels of 2.7, 14.0, and 3.1 micrograms per gram (g/g) of pipe material. This study has significant implications for understanding the benzene contamination of drinking water in the aftermath of wildfires that burned polymer pipes in California.

Tomato is considered moderately sensitive to salinity, which detracts from the quality and yield of its fruit; therefore, wild populations have been used as a genetic resource. The aim of this research was to identify lines derived from wild tomato populations with tolerance to salinity during the germination and seedling stages. During germination, 52 wild lines and 2 commercial hybrids (Imperial®, Reserva®) were subjected to 150 mM and 0 mM NaCl and evaluated. The test was carried out for 20 days in a germination chamber with constant darkness, temperature of 25±2 °C and relative humidity of 80±4%. At the seedling stage, 22 wild tomato lines with the best performance in the germination test and 2 commercial hybrids (Imperial®, Topanga®) were evaluated for 12 days in a floating raft system. Concentrations of 175 mM and 0 mM NaCl were used. During germination, the saline condition decreased germination percentage (65.2%), speed of germination (88.2%), steam length (72.5%), root length (46.56%), normal plants number (59.5%), stem dry matter (68.78%), root dry matter (61.99%), and total dry matter (67.1%). At the seedling stage, this condition decreased (P<0.05) the aerial part dry matter (46.37%), leaf area (59.35%), root length (42.43%), final plant height (40.24%), and growth rate (71.42%). Seventeen tolerant genotypes were identified at one of both developmental stages, while one genotype showed tolerance at both stages. These results indicate that there are different response mechanisms in each developmental stage. Native tomatoes play an important role in the identification of tolerant genotypes since they can be used as genetic resources for obtaining commercial genotypes with salt tolerance.

The use of disinfectants, particularly those containing quaternary ammonium compounds (QUACs), has dramatically escalated globally since the coronavirus disease 2019 pandemic. We report a case that highlights the risks associated with the ingestion of a low-concentration QUACs solution and emphasizes the importance of effective management in resolving severe lesions without sequelae. A 17-month-old boy experienced severe respiratory failure after ingesting a disinfectant containing benzalkonium chloride (BAC). The child was initially treated in a local emergency department and was subsequently transferred to a pediatric poison center. Upon evaluation, the child was found to have grade III-A corrosive esophageal lesions and chemical pneumonitis. Several complications, including massive pneumothorax and candidemia, occurred during the clinical course of the disease. However, with timely medical intervention and appropriate supportive care, the patient completely recovered without any long-term sequelae. The properties of BAC and a comprehensive management approach may have been responsible for the patient's full recovery despite the potential life-threatening effects of the ingestion of disinfectants.

The present research intents to study the evolution of the skin fatty acids and physiological disorders through cold storage in ‘Golden Delicious’ apples treated with 1-MCP and calcium. Harvested fruit were treated with calcium chloride (Ca), 1-MCP (MCP), Ca+MCP or no treatment (control) then subjected to cold storage at 0.5 ºC for 6 months. Fatty acids composition, Malondialdehyde (MDA) and the physiological disorders bitter pit (BP), superficial scald and diffuse skin browning (DSB) were measured at harvest and after storage plus 7 days shelf-life at room temperature ≈22 ºC. Palmitic acid decreased and linoleic acid increased through time, while oleic and stearic acids had few changes. Unsaturated/saturated fatty acids and MDA increased through time, despite Ca and Ca+MCP were related to lower MDA and lower BP and rotten fruit, after cold storage and shelf-life. In those treatments, the unsaturated/saturated fatty acids were higher, mainly due to higher linoleic acid and lower palmitic acids. Further research is needed to clarify the changes in membrane properties and the effect of some treatments in response to chilling injury through storage.

A novel prediction model for crack development of reinforced concrete (RC) piles with localized chloride corrosion in marine environment is proposed. A discrete method is used to solve the corrosion pit radius model and a crack extension model is developed to investigate the initiation and extension of cracks. The maximum corrosion degree of reinforced concrete pile is predicted according to the limit crack criterion, and finally a sensitivity analysis is carried out on the important parameters of crack extension. The results show that the radius of corrosion pit, the depth corrosion pit and cross-sectional area loss of reinforcement gradually increase as the corrosion level increases. The loss of local reinforcement section at crack initiation decreases with the increase of the ratio of concrete cover to initial diameter, and increases with the increase of pitting factor. The required pit depth for reinforcement cracking increases with the increase of the ratio of concrete cover thickness to diameter. The loss of cross-sectional area of reinforcement and the radius of corrosion pit increase with the increase of initial diameter of reinforcement. Increasing the pitting factor will reduce the pit depth and make the crack width develop faster before reaching the limit crack width. Increasing the concrete cover thickness can provide an improvement in the propagation of cracks. A comparative analysis shows that the localized corrosion pattern is more in conformity with marine engineering practice.

Molten salt reactors have gained substantial interest in the last years due to their flexibility and their potential for simplified closed fuel cycle operation for massive net-zero energy production. However, a zero-power reactor experiment will be an essential first step into the process of delivering this technology. The topic of the control and shut down for a zero power reactor is for the first time introduced through a literature review and the reduction of the control approaches to a limited number of basic functions with different variations. In the following, the requirements for the control and shutdown system for a reactor experiment are formulated, and based on these assessments, an approach for the shutdown – splitting the lower part of the core with reflector, and an approach for the control – a vertically movable radial reflector are proposed. Both systems will be usable for a zero-power system with a liquid as well as with as a solid core and even more importantly, both systems somehow work on the integral system level without disturbing the central part of the core which will be the essential area for the experimental measurements. Both approaches have been investigated as a singular system as well as their interactions with one another and the sensitivity of the control system. The study has demonstrated that both proposed systems are able to deliver the required characteristics with sufficient shutdown margin and a sufficiently wide control span. The interaction of the system has been shown to be manageable and the sensitivity is on a very good level. The multi-group Monte-Carlo approach has been cross evaluated by a continuous energy test leading to good results, but they also demonstrate that there is room for improvement.

Immersion in salt-lake solution was adopted to periodically test the concrete chloride-ion diffusion coefficient. The regression analysis was also completed. Also investigated was the time-dependent law of concrete chloride-ion diffusion coefficient with time. The influence of chloride-ion concentration in solution, water-to-cement ratio, and corrosion time on the largeness and accumulation rate of the concrete chloride-ion diffusion coefficient was also analyzed. Test results show that the concrete chloride-ion diffusion coefficient gradually decreased with increasing time and increased with increasing chloride-ion concentration in a salt lake . Taking into account the influence of factors such as water–binder ratio, chloride-ion concentration, and time-varying characteristics, a multi-factor calculation model for the concrete chloride-ion diffusion coefficient was established. Combining the prediction results and the measured data reported in this paper, the effectiveness and applicability of the established concrete chloride-ion diffusion coefficient calculation model were compared and verified, and the durability design and service life of a concrete structure under cool chlorine were compared. The results of analysis provide important boundary conditions.

Water quality monitoring was an important objective in the surroundings. In this study, we investigated the sensing characteristics of the arrayed flexible chloride sensor with XBee wireless sensing system. The sensitivity and linearity of the wireless chloride sensing devices were 91.6 mV/pCl and 0.988, respectively. The hysteresis voltages were 50.14 mV and 36.71 mV during the cycles of 1 M → 10⁻¹ M → 1 M → 10⁻³ M → 1 M and 1 M → 10⁻³ M → 1 M → 10⁻¹ M → 1 M, respectively. The selectivity coefficients of the ClO⁻ ion, ClO₄⁻ ion, NO₃⁻ ion and I⁻ ion for Cl⁻ ion were 5.0 × 10⁻², 1.0 × 10⁻¹, 5.9 × 10⁻³ and 5.6×10⁻¹, respectively. The sensing characteristics of real time measurement were investigated for dynamic microfluidic. The arrayed flexible chloride sensor was integrated with the microfluidic device, syringe pump and wireless sensing system. The sensitivity and linearity were 273.1 mV/pCl and 0.978 at 35 μL/min, respectively.

Considering the important demand of fresh water and its scarce availability, water desalination is an interesting technology, producing about 44 Mm³/year worldwide, but, in general the most common desalination techniques are highly energy demanding. Freezing-Melting (F/M) desalination uses just up to 70% less thermal energy, but is the least used process mainly, due to the difficulty of the salt separation. This study proposes a model able to analyses the thermodynamic potential that allows the salt diffusion during the F/M process, using an aqueous solution of sodium chloride. This should allow to obtain a sensitive analysis of the process to promote the separation between the high concentration brine and the ice with liquid separation by physical process. The unidimensional model is based on the evolution of both processes: thermal and mass diffusions, depending on temperature and saline gradients, predicting whether the salt will remain inside the ice or not. Thus, the thermal potential is adjusted to frozen only when the salt has been "pushed" towards the brine. Mostly models have base their results on the assumption of a “certain value of saline concentration of the liquid fraction”, value in which there is great disagreement. In this paper the calculations are based on the concentration in the solid-liquid interface, which has been extensively studied and there is a coincidence in those results, being the main advantage of the proposed model.

An efficient, eco-compatible and very cheap method for the construction of triazoles via eliminative azide–olefin cycloaddition (EAOC) reaction has been developed by a catalytic system IL/FeCl3, offering an highly regioselective approach to structurally diverse 1,5-disubstituted 1,2,3-triazoles in up to 95% yield. This strategy features the reuse of catalytic system through simple operations. Mechanistic studies indicated that an asynchronous concerted dipolar cycloaddition-elimination process might be involved.

For concrete structures exposed to offshore areas, chloride ion erosion is one of the main factors affecting the durability. It is crucial to evaluate chloride ion permeability resistance of concrete structures. In this article, a finite element simulation of the chloride ion diffusion process in concrete is conducted. A mass diffusion finite element model based on random aggregate approach is established to investigate the influence of aggregate, interface transition zone, and micro-cracks on chloride ion diffusion coefficients in concrete. The results show that the mass diffusion finite element analysis based on the exponential function model and power function model can effectively simulate the chloride ion diffusion process in concrete. In addition, the data reveal that coarse aggregate is the most important factor affecting chloride ion diffusivity in concrete. However, the interface transition zone significantly accelerates chloride ion diffusion in concrete. Moreover, this acceleration effect exceeds the barrier effect of aggregate.

Molten salt reactors have gained substantial interest in the last years due to their flexibility and their potential for simplified closed fuel cycle operation for massive net-zero energy production. The importance of a zero-power reactor for the process of developing a new, innovative rector concept like molten salt fast reactor is described here. It is based on historical developments as well as the current demand for experimental results and key factors that are relevant to the success of the next step in the development process of all innovative reactor types. In the systematic modelling & simulation of a zero-power molten salt reactor, the radius and the feedback effects are studied for a eutectic based system, while a heavy metal rich chloride-based system are studied depending on the uranium enrichment accompanied with the effects on neutron flux spectrum and spatial distribution. These results are used to support the relevant decision for the narrowing down of the configurations supported by considerations on cost and proliferation for the follow up 3D analysis to provide for the first time a systematic modelling & simulation approach for a new reactor physics experiment. The expected core volumes for these configurations have been studied using multi-group and continuous energy Monte-Carlo simulations identifying the 35% enriched systems as the most attractive and finally leading to the choice of the heavy metal rich compositions 35% enrichment as the reference system for future studies of the next steps in the zero power reactor investigation. The inter-comparison of the different applied codes and approaches available in the SCALE package has delivered a very good agreement between the results creating trust into the developed and used models and methods.

Triglycerides of waste cooking oil reacted with methanol in refluxing toluene to yield mixtures of diglycerides, monoglycerides and fatty acid methyl esters (FAMEs) in the presence of 20% (w/w) catalyst/oil using the hydrophilic sulfonated silica (SiO₂-SO₃H) catalyst alone or with the addition of 10% (w/w) co-catalyst/oil [(Bun4N)](BF₄) or Aliquat 336]. The addition of the ammonium salts to the catalyst lead to a decrease in the amounts of diglycerides in the products, but the concentrations of monoglycerides increased. Mixtures of [(Bun4N)](BF4)/catalyst were superior to catalyst alone or Aliquat 336/catalyst for promoting the production of mixtures with high concentrations of FAMEs. The same experiments were repeated using DMSO as the solvent. The use of the more polar solvent resulted in excellent conversion of the triglycerides to FAME esters with all three-catalyst media. A simplified mechanism is presented to account for the experimental results.

Clinker production is being reduced worldwide in response to the need to drastically lower greenhouse gas emissions. The trend began in the nineteen seventies with the advent of mineral additions to replace clinker. Blast furnace slag and fly ash, industrial by-products that were being stockpiled in waste heaps at the time, have not commonly been included in cements. Supply of these additions is no longer guaranteed, however, due to restrained activity in the source industries for the same reasons as in clinker production. The search is consequently on for other additions that may lower pollutant gas emissions without altering cement performance. In this research bentonite, a very common clay, was used as such an addition directly, with no need for pre-calcination, an still novel approach that has gone little explored to date for reinforced concrete with structural applications. The results of the mechanical strength and chemical resistance (to sulfates, carbonation and chlorides) tests conducted are promising. The carbonation findings proved to be of particular interest, for that is the area where cement with mineral additions tend to be least effective. In the bentonite-bearing material analysed here, however, carbonation resistance was found to be low as or lower than observed in plain Portland cement.

Molecular and morphological properties of poly(vinyl chloride) grains produced by suspension polymerization of VCM in the presence of a mixture of three kind of initiators (i.e. fast, mild and slow) (named as Cok process) was experimentally investigated in a pilot-scale reactor. The results obtained here were initially compared with a isothermal regular process (named as control process) and then with those obtained already for other productivity-enhancing polymerization techniques (i.e. nonisothermal and fast initiator dosage process). The results showed that, in contrast to nonisothermal and fast initiator dosage process, the addition of initators mixture at the beginning of the reaction has the smallest influence on molecular weight and polydispersity index compared to control process. It is obvioused that Cok-PVC grains have the lowest cold plasticizer absorption and porosity among these mentioned processes. Scanning electron microscopy (SEM) showed that the particles produced by Cok process are more regularly shaped, with a smoother surface compared with the control product. According to the literatures, all three productivity-enhancing techniques lead to an apparent quality enhancement, higher flowability and greater bulk density of final grains. While both processes of continous initiator dosage and nonisothermal polymerization broaden the particle size distribution of final PVC grains, applying initiator mixture produces particles with the same particle size distribution as control process. The SEM images processing showed that Cok process deccelerates the formation of a three-dimensional skeleton of primary particles relative to the control polymerization. In comparison with nonisothermal trajectory and continous fast initiator dosage system, the Cok polymerization process leads to the most delay of motionless conversions and fusion time as well.

One of the influential factors in estimating the service life of reinforced concrete bridges (RCB) is determining the long-term seismic performance of these structures. Corrosion due to chloride ion diffusion leads to the destruction of critical members of the RCB during the useful life of the structure. So, the long-term seismic performance of the bridge deteriorates as a result. It is essential to study the effect of corrosion deterioration on the long-term seismic performance of bridges in the southern regions of Iran, near the coasts of the Persian Gulf and the Oman Sea, because of the seismicity of the region and high corrosion rate of reinforced concrete (RC) members is the result of environmental conditions. In order to investigate this issue, considering studies about environmental conditions of southern Iran, the onset time of corrosion in the columns, as seismic critical members of the bridge, was determined. Based on that, the corrosion's effect on characteristics of RC at specific time points during the bridge's useful life (0, 15, 30, 45, 60, 75 and 90 years) have been calculated. The effects of corrosion include deterioration of the core and cover concrete properties, steel bar and the connection between concrete and steel bar. In the next step, at each time point, according to the modified stress-strain relationships, the moment-curvature analysis of the bridge pier was done, and the properties of the plastic hinge were determined. Finally, based on the obtained data about plastic hinge characteristics at each time point, overload analysis of the bridge was performed in both longitudinal and transverse directions. Then the capacity curves of RCB were compared at the mentioned time-points. The results show that the capacity of the bridge deteriorates over time due to corrosion. Therefore, a proposal to increase the value of base shear design has been made to ensure the long-term seismic performance of RCB in corrosive environments.

We discuss the electrodeposition of two-dimensional (2D) Pt-nanostructures on HOPG achieved under constant applied potential versus a Pt counter electrode (Eappl = ca. - 2.2 V vs RHE). The deposition conditions are discussed in terms of the electrochemical behavior of the electrodeposition precursor (H2PtCl6). We performed cyclic voltammetry (CV) of the electrochemical Pt deposit on HOPG and on Pt substrates to study the relevant phenomena that affect the morphology of Pt deposition. Under conditions where the Pt deposition occurs and H2 evolution is occurring at the diffusion-limited rate (- 0.3 V vs RHE), Pt forms larger structures on the surface of HOPG, and the electrodeposition of Pt is not limited by diffusion. This indicates the need for large overpotentials to direct the 2D growth of Pt. Investigation of the possible effect of Cl- showed that Cl- deposits on the surface of Pt at low overpotentials, but strips from the surface at potentials more positive than the electrodeposition potential. The CV of Pt on HOPG is a strong function of the nature of the surface. We propose that during immersion of HOPG in the electrodeposition solution (3 mM H2PtCl6, 0.5 M NaCl, pH 2.3) Pt islands are formed spontaneously, and these islands drive the growth of the 2D nanostructures.

The selective extraction of metals from aqueous solutions is very important stage in hydrometallurgical processing of metallic waste. Leach solutions are usually a multi-component mixture. The main impurity of aqueous solutions obtained after leaching using inorganic acids is iron. In this work, the membrane separation of iron(III) from nickel(II), cobalt(II) and lithium(II) was studied. The facilitated transport of metal ion using the polymer inclusion membranes (PIMs) with tetrabutylammonium bromide (TBAB) as an ion carrier under various conditions was analyzed in detail. The several factors such as the ion carrier concentration in the membrane as well as the effect of the inorganic acids concentration in the source/receiving phases on the kinetic parameters were investigated. The results show that ionic liquid TBAB is a very selective ion carrier of Fe(III) towards Ni(II), Co(II) and Li(I) .

In this study, the effect of extraction conditions on the total phenolic content of clove buds was investigated. Clove buds were extracted using a deep eutectic solvents like mixtures choline chloride: lactic acid in the 1:2 molar ratio. Additionally, the HPLC-DAD method was used to determine the main components of the clove extracts, including eugenol, eugenol acetate, and β-caryophyllene. The conditions used in the extraction with choline chloride: lactic acid (molar ratio 1:2) included extraction temperature (t = 40 – 80°C), water addition (5.6 – 40%), and extraction time (30 – 90 min). Determination of the phenolic compounds was done by the Folin-Ciocalteu method. The optimum operating conditions for the total phenolic content were identified at 77°C, 30 min, and a water addition of 40%. Based on the results, the highest amount of eugenol (307.26 ± 8,44 mg/g dry raw material) was determined in clove extracts which were extracted under condition of 60°C, 22.8%, and 30 min.

The interfacial polymerization (IP) of piperazine (PIP) and trimesoyl chloride (TMC) has been extensively utilized to synthesize nanofiltration (NF) membranes. However, it is still a huge challenge to monitor the IP reaction, because of the fast reaction rate and the formed ultra-thin film. Herein, two effective strategies were applied to reduce the IP reaction rate: (1) the introduction of hydrophilic interlayers between the porous substrate and the formed polyamide layer, and (2) the addition of macromolecular additives in the aqueous solution of PIP. As a result, in situ Fourier transform infrared (FT-IR) spectroscopy was firstly used to monitor the IP reaction of PIP/TMC with hydrophilic interlayers or macromolecular additives in the aqueous solution of PIP. Moreover, the formed polyamide layer growth on the substrate was studied in a real-time manner. The in situ FTIR experimental results confirmed that the IP reaction rates were effectively suppressed and that the formed polyamide thickness was reduced from 138 ± 24 nm to 46 ± 2 nm according to TEM observation. Furthermore, an optimized NF membrane with excellent performance was consequently obtained, which included boosted water permeation of about 141–238 (L/m²·h·MPa) and superior salt rejection of Na₂SO₄ > 98.4%.

In cold-climate regions, road salt is used as a de-icer for winter road maintenance. The applied road salt melts ice and snow on roads, being washed off through storm sewer systems into nearby urban streams, harming the freshwater ecosystem. Addressing the gap in the knowledge regarding the use of deep learning approaches for urban stream water quality forecasting, the present work discusses our implementation of a “Graph Neural Network” - “Sample and Aggregate” (GNN-SAGE) model for forecasting chloride concentrations in the Credit River in Ontario, Canada. The proposed GNN-SAGE is compared to other models, including a Deep Neural Network based transformer (DNN-Transformer) and a benchmarking persistence model for 6 hours forecasting horizon. Ac-cording to the results, the GNN-SAGE model surpasses other models in providing accurate predic-tions of chloride concentrations within the assessed prediction window. Also, a SHAP analysis provides insight into the variables that influence the model’s forecasting, showing the impact of the spatiotemporal neighbouring data from the network and the seasonality variables on the model’s result. The GNN-SAGE model shows potential for use in real-time forecasting of water quality in urban streams, aiding in the development of regulatory policies to protect the vulnerable freshwater ecosystems in urban areas.

Deep eutectic solvents (DESs) have emerged as novel alternatives to common solvents and VOCs. Their employment as electrolytes in battery has been an area of intense research. In this context, understanding changes in physicochemical properties of DESs in the presence of Li salts becomes of utmost importance. Solvatochromic probes have potential to gauze such changes. It is reported herein that one such uv-vis molecular absorbance probe, Reichardt’s betaine dye 33, effectively manifests changes taking place in a DES Glyceline, composed of H-bond accepting salt choline chloride and H-bond donor glycerol in 1 : 2 molar ratio, as salt LiCl is added. Lowest energy intramolecular charge-transfer absorbance band of this dye exhibits 17 nm hypsochromic shift as up to 3.0 molal LiCl is added to Glyceline. The estimated ETN parameter shows linear increase with LiCl mole fraction. Spectroscopic responses of betaine dye 33, N,N-diethyl-4-nitroaniline and 4-nitroaniline are used to assess empirical Kamlet-Taft parameters of dipolarity/polarizability (π*), H-bond donating acidity (α) and H-bond accepting basicity (β) as a function of LiCl concentration in Glyceline. LiCl addition to Glyceline results in increase in α and no change in π*and β. It is proposed that added lithium interacts with oxygen of the –OH functionalities on the glycerol rendering the solvent with increased H-bond donating acidity. It is observed that pyrene, a popular fluorescence probe of solvent polarity, does respond to the addition of LiCl to Glyceline, however, the change in pyrene response starts to become noticeable only at higher LiCl concentration (mLiCl ≥ 1.5 m). Reichardt’s betaine dye is found to be highly sensitive and versatile in gauzing physicochemical properties of DESs in the presence of LiCl.

Background. Traumatic brain injury (TBI) is the main cause of disabilities over the industrialized countries. Cognitive decline appears in the chronic phase of the pathology consecutively to cellular and molecular processes. Here we described the use of KCC2, a neuronal-specific potassium-chloride transporters as potent biomarker to predict cognitive dysfunctions after TBI. Methods. Using neuronal and total exosomes collection from blood serum in control and TBI subjects we were able to anticipate the decline of cognitive performance. Results. After TBI, we observed a significative and persistant loss of KCC2 expression in the blood exosomes that is correlated to changes in network activity and cellular processes such as secondary neurogenesis. Also we correlated this KCC2 loss in expression to the appearance of the cognitive decline observed in mice and more particularly we correlate the KCC2 loss of expression to the appearance of the depressive-like behavior. Conclusion. According to our protocol, we were able to confirm our previous findings in agreement with the potential therapeutic effect of bumetanide in the prevention of the post traumatic depression after TBI, by restoring the KCC2 expression thus preventing the massive neuronal death of interneurons and the secondary neurogenesis effect observed in such model.

The seeds of red clover are heteromorphic and two color morphs can be visually recognized, light purple and yellow, resulting from heterozygosity and recessive homozygosity at two loci. Here, we report the responses of seed imbibition, seed germination, and early seedling growth of the two morphs to distilled water, sodium chloride, and complete nutrient solution. The sensitivity of red clover seeds to treatments increased with the stage of development in what seems to be a cumulative process. No differences were found in seed imbibition between morphs or between treatments. In seedling growth, on the contrary, treatments were always effective, but differences between morphs were only observed in seeds that were treated with nutrient solution, whereas in the intermediate stage of seed germination, the effects by treatments were observed together with the appearance of differences between morphs in distilled water and in the treatment by sodium chloride solution. Simultaneously, the superior performance of the yellow morph that was found in germination, which appears to be a trait stable across cultivars of red clover seeds, turned into a superior performance of the light purple morph in seedling growth.

Nitrogen is the most commonly managed mineral nutrient in olive groves because it is essential for plant growth. The precise management of N fertilization in olive cultivation is still not fully clarified, but it is now essential for providing sustainable production. A nitrogen fertilizer ex-periment with olive trees (cv. Kalinioti) was carried out over a six-year period. Seven levels of nitrogen fertilizer given as ammonium nitrate (control, 1, 2, 3, 4, 5, and 6 kg/tree) were annually applied in order to determine the effect of nitrogen on vegetative growth, fruit set, fruit weight, yield, maturation index and leaf N,P, and K concentrations. The results indicate that, under these conditions, application of up to 4 kg NH4NO3/tree significantly increased yield to 62.5 kg/tree compared to the control. The positive effect was attributed to the initial and final fruit set increases (7.63 and 3.73%, respectively). However, the weight of 100 olives (337 g) at the same fertilizer rate was considerably lower compared to the control. Higher nitrogen rates decreased yield while increasing overall shoot growth. Nitrogen fertilization did not significantly influence the oil content of olive fruit. Fruit weight, maturation index and concentration of oil reached maximum levels in the beginning of December, indicating a suitable start to olive harvesting with reduced yield losses due to unfavorable weather conditions. With increasing fertilizer levels from 0 to 6 kg NH4NO3,/tree concentration of N in olive leaves also increased from 1.23% to 2.38%. Maximum yield was achieved at a level of 6 kg NH4NO3/tree, which corresponded to 2.01% N in leaves. The results suggest that application of 3 kg NH4NO3/tree can be recommended for table olive pro-duction due to the fact that fruit weight was not decreased, while fertilization with 4 kg NH4NO3/tree was suitable for oil olives.

In recent years, technical processes for the sequestration of CO2 through industrial waste mineral carbonation have been explored and developed. There is a large portfolio of Carbon Capture, Uti-lisation and Storage (CCUS) techniques that have been employed on a laboratory and at pilot scale. These include geological storage, ocean storage and mineralisation by carbonate ores. In view of this, the main purpose of this research was to investigate and explore chemical variables, particularly ammonium salts as lixiviants for calcium mineral extraction from iron making slag. The slag in use was acquired from a Steel Mill in the Vaal Triangle Region in Gauteng, South Af-rica. The experimental test work was conducted using different ammonium lixiviants, namely, NH4NO3, NH4Cl and CH3COONH4 to understand the influence of anion type as well as possible differences in mechanisms of interactions. Lixiviant concentration as well as the reaction time were varied in this research study. The three selected ammonium based lixiviants showed different extents of calcium extraction owing to differences in the anion groups. NH4NO3, NH4Cl and CH3COONH4 were found capable of dissolving 50% to 80% of calcium from the selected slag for different molar concentrations. Anion type and leaching time also had significant influences on the leaching of calcium from the slag. Rapid pH degradation resulted in better calcium extraction ca-pabilities. This work has shown that the selected ammonium salts have a potential as lixiviants for calcium dissolution from iron making blast furnace slags. These lixiviants would therefore be important to consider during calcium mineral carbonation for CO2 sequestration.

Synthesis and antitumour activity of a palladium compound, [Bis (quinoline) palladium (II) chloride] (coded as NH1) alone and in combination along with its proposed mechanism of action has been described in the present study. Antitumour activity has been performed in seven different cancer cell lines using colorimetric 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl-2H-tetrazolium bromide (MTT) assay. The investigated palladium compound demonstrated superiority over clinical standard cisplatin against drug resistant ovarian cancer cell lines. NH1 also demonstrates 4.4 times greater activity than cisplatin against breast cancer model. Binary sequenced combination study showed that NH1 in combination with curcumin is mostly additive to antagonistic. However, combination of NH1 with 6-shogaol demonstrated synergism depending on dose and sequence. Proteomic study revealed that changes in expression of 14 proteins were significantly associated with anticancer mechanism of NH1. In vivo anticancer activity of NH1 at a dose of 0.75 mg/kg was also evaluated using Erlich Ascites Carcinoma (EAC) cell lines in Swiss-albino mice model. Preliminary toxicity study in Swiss-albino mice proved that NH1 is comparatively less toxic at both of the administered doses, either 2.5 mg/kg or 5 mg/kg. However, cisplatin demonstrated significant toxicity at both of the administered doses. Biochemical investigations also supported that NH1 demonstrated lesser toxicity profile towards liver or kidney compared to clinical standard cisplatin.

The anodic polarization response of magnesium alloy AZ31 was characterized during exposure to aerated 0.1M NaCl solutions with millimolar additions of NaVO₃, Na₃PO₄, Na₂HPO₄, NaF and various pairings to assess their ability to inhibit corrosion kinetics and retard localized corrosion. Each of the candidate inhibitors reduced the corrosion rate of the alloy to some degree. A Na₃PO₄ - NaVO₃ pair produced a powerful inhibiting response decreasing the corrosion rate to about 10^-7 A/cm², which was two orders of magnitude lower than the uninhibited control case. A Bliss Independence assessment indicated that this inhibitor pair acted synergistically. A Na₂HPO₄ - NaVO₃ pair reduced the corrosion rate to 10^-6 A/cm² but was not assessed to be acting synergistically. The NaVO₃ - NaF pair did not reduce the corrosion rate significantly compared to the control case and was an antagonistic pairing. SEM imaging showed film formation due to exposure, which appears to be the origins of the observed inhibition. The resistance to localized corrosion was assessed as the difference in the breakdown potential and the corrosion potential with larger values indicating a lower probability of localized corrosion during free corrosion exposures. Effects of the inhibitors on this characteristic were mixed, but each of the inhibitor pairs yielded potential differences in excess of 100mV. A conceptual conversion coating process based on a mixture of vanadate and phosphate compounds were demonstrated. A fluoride-bearing formulation produced coatings whose total impedance was increased by a factor or 2 compared to an uncoated control. A fluoride-free formulation produced coatings whose corrosion resistance was increased by more than a factor of 3.

Nitriding has long been used to engineer the surfaces of engineering steels to improve their surface and subsurface properties. The role of the surface compound layer (’-Fe4N and/or -Fe2-3N) in improving the tribological and corrosion resistant properties of nitrided steels has been established. However, there have been very few studies on the response of the compound layer to tribocorrosion in corrosive environments. In this work, the tribocorrosion behaviour of a 5 m thick ’-Fe4N nitride layer produced on mild steel (MS) by plasma nitriding has been studied in a NaCl containing solution under various electrochemical conditions. The results show that at a cathodic potential, where mechanical wear is predominant, the total material removal (TMR) from the ’-Fe4N layer is 37% smaller than that from the untreated MS, and at open circuit potential, TMR from the layer is 35% smaller than that from the untreated MS, while at an anodic potential, the ’-Fe4N layer can reduce TMR from mild steel by 87%. The beneficial effect of the ’-Fe4N nitride layer in improving the tribocorrosion behaviour of mild steel is derived from its high hardness and good corrosion resistance in the test solution and its ability to resist both mechanical wear and chemical wear.

Molten salt reactors have gained substantial interest in the last years due to their flexibility and their potential for simplified closed fuel cycle operation for massive net-zero energy production. However, a zero-power reactor experiment will be an essential first step into the process delivering this technology. The choice of the optimal reflector material is one of the key issues for such experiments since on the one hand it offers huge cost saving potential due to reduced fuel demand, on the other hand an improper choice of the reflector material can have negative effects on the quality of the experiments. The choice of the reflector material is for the first time introduced through a literature review and a discussion of potential roles of the reflector. The 2D study of different potential reflector materials has delivered a first down selection with SS 304 as representative for stainless steel, lead, copper, graphite, and beryllium oxide. A deeper look identified in addition iron-based material with high Si content. The following evaluation of the power distribution has shown the strong influence of the moderating reflectors creating a massively disturbed power distribution with a peak at the core boundary. This effect has been confirmed through a deeper analysis of the 2D multi-group flux distribution which lead to the exclusion of the BeO and the graphite reflector. The most promising materials identified have been SS 304, lead, and copper. The final 3D Monte-Carlo study demonstrated that all three materials have the potential to reduce the required amount of fuel by up to 60% compared NaCl which has been used in previous studies and is now taken as reference A first cost analysis has identified the SS 304 reflector as the most attractive solution. The results of the 2D multi group deterministic study and the 3D multi group Monte-Carlo study have been confirmed through a continuous energy Monte-Carlo reference calculation showing only minor differences.

Nasopharyngeal carcinoma (NPC) has not been thoroughly studied, and the pathogenesis of NPC is unclear. Scientists have neither discovered effective therapies nor achieved a desirable prognosis. Some studies have found that the regulation of intra- and extracellular ion channels hinges directly on cell apoptosis, and treatment with Gambogenic acid (GNA) brings changes to the volume-sensitive outwardly rectifying chloride (VSOR Cl-) current of CNE-2Z cells recorded by the patch clamp method. Nevertheless, rarely have any researchers probed into the relevance between this variation and the anti-tumor mechanism of GNA. This paper is suggested that GNA activates the VSOR Cl- current on the CNE-2Z cell membrane, and the activation of VSOR Cl- currents by GNA in CNE-2Z cells is blocked by the chloride channel blockers DIDS and DCPIB. GNA induces the down-regulation of GRP78 and up-regulation of ATF4 as well as chop proteins, which is evidence for the induction of CNE-2Z cell apoptosis, and this correlates with ER stress. GNA can activate the VSOR Cl- channel and lead to the occurrence of ER stress, thus inducing the apoptosis of CNE-2Z cells and inhibiting the proliferation of CNE-2Z cells.

Ionic liquids (ILs) have gained interest among researchers due to its tunable properties that can be used in wide applications. However, toxicity and bio-degradation studies of ILs proved that most of the aromatic ILs, such as imidazolium is highly toxic and non-biodegradable. Several advance oxidation processes (AOPs) have been investigated by researchers to evaluate the efficiency of the systems for the removal of ILs from wastewater. However, the issue on relative high cost and environmental concern has limited the application of these AOPs in industry. In this research, photocatalytic study using hybrid nano-materials was conducted to evaluate the efficiency of this system as an alternative AOP system for removal of ILs from wastewater. The synergistic effect of adsorption-photodegradation was introduced by depositing Fe-TiO₂ onto the functionalized activated carbon (AC). Nano-TiO₂ was synthesized using micromulsion method before modification with transition metal and deposited onto the oxidized AC. Photodegradation reaction of 1-butyl-3-methylimidazolium chloride [bmim]Cl was investigated under simulated visible light irradiation. It was observed that the overall efficiency of the system was increased with the increasing amount of Fe dopant. Investigation on the extrinsic factors such as solution pH, initial concentration of ILs and photocatalyst dosage showed to significantly affect the overall efficiency of the systems where the optimum condition for the system was observed at pH 10, with initial ILs at 1mM at 1 g/L of photocatalyst. The best performance photocatalyst was 0.2Fe-TiO₂/AC.

The steady-state dissolution rates of basaltic glass and labradorite have been measured in the presence of 10 to 700 x 10-3 mol kgw-1 aqueous NaCl, KCl, CaCl2, and MgCl2 at 25 oC. All rates were measured in mixed flow reactors, and at pH~3.6 by the addition of HCl to the reactive fluids. Steady-state basaltic glass dissolution rates based on Si release increased by ~0.3 log units in the presence of 1 x 10-2 mol kgw-1 of CaCl2 or MgCl2, compared to their rates in 10 x 10-3 mol kgw-1 of NaCl, and KCl. In contrast, the steady-state dissolution rates of labradorite decreased by ~0.4 log units in the presence of 10 x 10-3mol kgw-1 of CaCl2 or MgCl2, compared to their rates in 10 x 10-3 mol kgw-1 of NaCl, and KCl. These contrasting behaviours likely reflect the varying effects of these cations on the stability of rate controlling Si-rich activated complexes on the surface of the solids. On average, the Si release rates of these solids are similar to each other and increase slightly with increasing ionic strength. As the pH of water charged with 10 to 30 bars CO2 is ~3.6, the results of this study indicate that both basaltic glass and labradorite dissolution will likely be effective at increasing pH and adding Ca to the aqueous phase in saline fluids. This observation supports potential efforts to store carbon through its mineralization in saline aquifers containing Ca-bearing feldspar and in submarine basalts.

The dessert banana is a popular fruit worldwide, but its ripening process is greatly accelerated by high temperatures, which eventually leads to an unpleasant taste and the appearance of spots on the skin of the fruit. To slow down the ripening of bananas, expensive strategies are used, which are usually not practical for conventional farmers in less developed countries. In this study, we try to find a less costly alternative. Therefore, the effects of coatings of lemon peel extract (2.5 %, 5 %, and 10 %), calcium chloride (4 %), and glycerol (2 %) on the shelf life and postharvest quality of banana fruit (Cavendish) stored at 20 ± 3 °C and 50 – 70 % relative humidity were investigated. Treatment with a mixture of 2.5 % lemon peel extract and 2 % glycerol resulted in an extension of the shelf life of the dessert banana by up to 6 days and no detectable fungal infestation. The mixture is an effective alternative to extend the shelf life and reduce quality losses in bananas.

The thermal stabilizers, lubricant, and plasticizers are three crucial additives for processing poly (vinyl chloride) (PVC). In this study, a new mannitol stearate ester-based aluminum alkoxides (MSE-Al) was designed and synthesized as a novel additive for PVC. The thermal stability and processing performance of PVC stabilized by MSE-Al were evaluated by Congo red test, conductivity measurement, thermal aging test, ultravioletevisible (UV-vis) spectroscopy test, and torque rheometer test. Results showed that the addition of MSE-Al can not only markedly improve the long-term thermal stability of PVC, but also greatly accelerate the plasticizing and decrease the balance torque which demonstrated that MSE-Al possesses the lubricating property. Thus, MSE-Al was demonstrated to be able to provide tri-functional additive roles, e.g., thermal stabilizer, plasticizer, and lubricant. The test results for the thermal stability of PVC indicated that the initial whiteness of PVC stabilized with MSE-Al was not good enough, thus the synergistic effect of MSE-Al with zinc stearates (ZnSt₂) on the thermal stability of PVC was also investigated. The results showed that there exhibited an appreciable synergistic effect between MSE-Al and ZnSt₂. The thermal stabilization mechanism and synergism effect of MSE-Al with ZnSt₂ were then discussed.

Regulation (EU) No 305/2011 lays down harmonized conditions for marketing construction products in the European Union. One of its consequences has been the introduction of the product standard EN 50575 and standard EN 130501-6, concerning power, control, and communication cables permanently installed in buildings to prevent the risk of a fire and its consequences. EN 13501-6 provides the reaction to fire classifications for cables, the test methods to be performed, the requirements to meet a specific reaction to fire, and additional classifications for smoke production, flaming droplets, and acidity. EN 60754-2 is the technical standard used to assess acidity, and it defines three classes: a1, a2, and a3 (the less performant), based on pH and conductivity measurements. Due to the release of hydrogen chloride during the combustion, acidity is the weak point of PVC cables, which are not yet capable of achieving the a1 or a2 classes required in specific locations according to a fire risk assessment. EN 13501-6 does not include EN 60754-1. Both EN 60754-1 and EN 60754-2 are common standards for determining halogen gas content, acidity, and conductivity, respectively. They involve the same type of tube furnace but with different heating regimes, final temperatures, and detection methods. EN 60754-2 must be performed at temperatures between 935 – 965 °C. The paper demonstrates that, when EN 60754-2 is carried out with the thermal profile of EN 60754-1 or at 500 °C in isothermal conditions, the evolution of hydrogen chloride changes significantly if potent acid scavengers are utilized in the PVC compounds. The reason lies behind the kinetic of hydrogen chloride release during the combustion of PVC compounds: the higher the temperature or faster the heat release, the quicker hydrogen chloride evolution and the lower the probability for the acid scavenger to trap it. That further highlights the "fragility" of EN 60754-2 as a tool for assessing the risks associated with the release of hydrogen chloride in case of fire

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

The combustion of PVC cables in fires results in the release of hydrogen chloride gas. In the European Union, Regulation (EU) No 305/2011, in force since 2017, requires the classification of cables permanently installed in buildings for reaction to fire, smoke, flaming droplets, and acidity. The additional classification for acidity is evaluated through EN 60754-2, involving pH and conductivity measurements. This study focuses on the essential research and development of low-smoke acidity PVC compounds for cables, mainly aiming to meet the stringent additional classifications for acidity, a1 or a2, which cannot be achieved with traditional PVC cables. Understanding the chemistry of thermal decomposition and combustion, especially in the presence of hydrogen chloride scavengers, is crucial for meeting the best acidity classification. The article reviews the current tube furnace tests used in the European Union for cable halogen and acidity assessments. It discusses the limitations of the existing method (EN 60754-2) and highlights the potential of emerging tests such as IEC EN 60754-3, which employs ion chromatography for improved sensitivity and specificity. In the experimental part of the article, various standard and low-smoke acidity cable compounds are tested using tube furnace experiments with different heating regimes. The concentrations of cations and anions in solution are measured through ion chromatography and inductively coupled plasma–optical emission spectrometry. This detailed analysis aims to identify the species influencing pH and conductivity, which is crucial for designing effective acid scavengers that do not impact conductivity. The conclusive results emphasize that HCl from PVC thermal decomposition is the primary driver of pH and conductivity, and the contribution from the decomposition of additives and byproducts from combustion is found to be negligible in most of the tested PVC compounds for cables. The findings underscore the importance of understanding the thermal decomposition of PVC compounds to design acid scavengers capable of trapping hydrogen chloride without adversely impacting conductivity.

Redox-flow batteries are rechargeable batteries that store energy in two liquid electrolytes, separated by a membrane. During charging and discharging, the electrolytes flow through the membrane and undergo chemical reactions that generate or consume electrical energy. These batteries are known for their scalability and long cycle life and are versatile energy storage technologies developed to enhance efficiency and lower costs. Deep Eutectic Solvents (DES) are eco-friendly alternatives to traditional electrolytes, and their properties have been studied to improve the performance of redox-flow batteries. We investigated choline chloride/ethylene glycol (ChlCl/Eg) mixtures with LiPF6 salt at four concentrations through experimental and MD simulations. The thermophysical and transport properties of the mixture, including density, diffusion coefficient, viscosity, and ionic conductivity, were calculated across a temperature range of 298.15–398.5 K. Our findings indicate that an increase in salt concentration leads to a decrease in diffusion coefficients and ionic conductivity, while increasing the viscosity of the deep eutectic solvent. This research provides valuable insights into the behavior of DES mixtures and can aid in the design and optimization of DES-based processes for use in redox-flow batteries.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

To secure logic circuits against the illegal copying the insertion of the so-called key bit inputs using XOR/XNOR gates has been proposed in . The inserted gates modify (lock) the behavior of the original circuit and only the correct choice of the secret key bits guarantees the equivalent behaviour of the locked circuit to the original circuit. To break this kind of security, i.e. to find the secret key bits, there was a SAT solver based attack proposed in . The aim of this work is to experimentally verify this attack on several locked circuits with various number of primary inputs and outputs and with various number of gates. Except for the random placement of the key gates we evaluate also the positioning with chaining elimination. The obtained and presented results show that we were able to unlock 10 of 11 circuits within few minutes on a common PC.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Early discharge after childbirth has led to a rise in neonatal readmission, becoming a major concern in recent decades. Our research aimed to identify the risk factors and incidence of neonatal readmission, as well as explore preventive measures. Our study at the Clinical Hospital of Pediatrics in Ploiești, Romania included 108 neonates admitted during the neonatal period. This accounted for 2.06% of all admissions (5226). The most prevalent cases were malnutrition (25%), fever (20.3%) and bronchiolitis (17.5%). Diarrhea and infectious gastroenteritis were also observed (14.8%), along with acute rhinoconjunctivitis (9.2%) and late onset sepsis (3.7%). No deaths were recorded. The most significant characteristics identified were number of children (p&lt;0.001) and age at maternity discharge (p&lt;0.001). By following the prevention rules, malnutrition, feeding errors, and infections can be avoided. This includes practicing proper hand hygiene for both mothers and medical staff, as well as educating and demonstrating to mothers the benefits of breastfeeding. In addition, all newborns discharged from the maternity ward should benefit from follow-up at 7-10 days of life. Our results confirm the effectiveness of a multidisciplinary team and endorse promoting breastfeeding. Implementing quality control measures and regularly evaluating the surveillance program will help improve its effectiveness.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Brain aging causes a wide variety of changes at molecular and cellular levels, leading to the decline of cognitive functions and increased vulnerability to neurodegenerative disorders. The research aimed at understanding the aging of the brain has made much progress in recent decades. Technological innovations such as single-cell RNA-sequencing (scRNA-seq), proteomic analyses, and spatial transcriptomic analyses have facilitated the research on the dynamic changes occurring within neurons, glia, and other cells along with their impacts on intercellular communication during aging. In this review, we introduce recent trends of how neurons and glia change during aging and discuss the impact of the brain microenvironment such as the blood-brain barrier (BBB).

Museums are called to respond to contemporary challenges and contribute to the formation of more progressive societies. One of the major challenges of our time is climate change and museums could construct cocreated narratives around climate and implement targeted actions for the audiences through their sensorial and affective experiences. More specifically, Geology and Palaeontology museums are repositories of knowledge on geoheritage and geoconservation, recognized for their scientific, pedagogical, cultural and recreational values. The educational potential of geological and paleontological exhibits could be used in informal education activities regarding the climate emergency. Taking the above into consideration, this study focuses on both the creation and evaluation of an educational program for the Natural History Museum of Arsakeio Campus at Psychicko.

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

At 12:28 UTC (8:28 PM, local time) on 15 January 2023, a shallow, moderate earthquake with a magnitude (Mw) of 4.7 and a depth of one (1) kilometer shook the northern part of Leyte Island in the central part of the Philippines. The ground shaking was felt at PHIVOLCS Earthquake Intensity Scale (PEIS) VI, (very strong) equivalent to Modified Mercalli Intensity (MMI) VI in areas along the strike of the Leyte segment of the Philippine Fault. Even though this earthquake is classified as moderate in size, significant geologic, structural, and socio-economic impacts were documented. Most of the earthquake impacts that include surface rupture, liquefaction, and mass movements are limited near the epicentral area. The earthquake produced an 8-km-long surface rupture, the first documented rupture generated by a magnitude &lt;6 along the Philippine Fault, and is unusual in other surface rupturing earthquakes worldwide. It injured 18 persons and damaged 434 residential buildings and 26 public infrastructures which amounts to about 500 thousand US dollars. Structural damages were caused by surface rupture and/or poor engineering construction practices. Analysis of the seismic waveform and recorded peak ground acceleration (PGA) suggests that the subsurface geology influenced the ground motion amplification in an area near the epicenter. Based on the hypocenter, focal mechanism solution, aftershock distribution, and actual field observation, the causative fault for this event is the northern end of the Philippine Fault – Leyte segment. Moderate in size, this earthquake emphasizes the need and importance of documenting moderate-sized earthquakes as a tool and guide for medium and long-term earthquake risk assessment and resiliency.