This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

A sustainable low cost activated carbon substitute was produced based on pretreated lignocellulosic biomass, especially spruce sawdust. A harmful liquid waste, desalination brine was used for the treatment of a solid wood industry waste, spruce sawdust. This approach is in the circular economy theory and aims to the decarbonization of the economy. The pretreated sawdust was tested as an adsorbent appropriate for the removal of a commonly used pollutant, methylene blue, from industrial wastewater. The adsorption capacity of the pretreated material was found to increased four times comparing to the untreated one in the case that the Freundlich equation was fitted to the isotherms’ data. The treatment experimental conditions with desalination brine that gave maximum adsorption capacity correspond to 1.97 combined severity factor in logarithmic form value. The same adsorption capacity was found to increase five to six times comparing to the untreated spruce sawdust in the case that the Langmuir isotherm model was applied at the same data. Moreover, kinetic experiment was cried out as regards the methylene blue adsorption process. The desalination brine pretreated sawdust adsorption capacity increased 1.4 times comparing to the untreated one, in the case of the Lagergren kinetic equation fitting. Furthermore, the adsorption capacity of the same material was increased 1.6 times when the second order kinetic model was applied to the same data. Industrial scale applications can be based on the kinetic data findings as they have to do with a very shorter adsorption period comparing to the isotherm data.

Large-scale hydrological modeling in China is challenging given the sparse meteorological stations and large uncertainties associated with atmospheric forcing data.Here we introduce the development and use of the China Meteorological Assimilation Driving Datasets for the SWAT model (CMADS) in the Heihe River Basin(HRB) for improving hydrologic modeling, by leveraging the datasets from the China Meteorological Administration Land Data Assimilation System (CLDAS)(including climate data from nearly 40000 area encryption stations, 2700 national automatic weather stations, FengYun (FY) 2 satellite and radar stations). CMADS uses the Space Time Multiscale Analysis System (STMAS) to fuse data based on ECWMF ambient field and ensure data accuracy. In addition, compared with CLDAS, CMADS includes relative humidity and climate data of varied resolutions to drive hydrological models such as the Soil and Water Assessment Tool (SWAT) model. Here, we compared climate data from CMADS, Climate Forecast System Reanalysis (CFSR) and traditional weather station (TWS) climate forcing data and evaluatedtheir applicability for driving large scale hydrologic modeling with SWAT. In general, CMADS has higher accuracy than CFRS when evaluated against observations at TWS; CMADS also provides spatially continuous climate field to drive distributed hydrologic models, which is an important advantage over TWS climate data, particular in regions with sparse weather stations. Therefore, SWAT model simulations driven with CMADS and TWS achieved similar performances in terms of monthly and daily stream flow simulations, and both of them outperformed CFRS. For example, for the three hydrological stations (Ying Luoxia, Qilian Mountain, and ZhaMasheke) in the HRB at the monthly and daily Nash-Sutcliffe efficiency ranges of 0.75-0.95 and 0.58-0.78, respectively, which are much higher than corresponding efficiency statistics achieved with CFSR (monthly: 0.32-0.49 and daily: 0.26 – 0.45). The CMADS dataset is available free of charge and is expected to a valuable addition to the existing climate reanalysis datasets for deriving distributed hydrologic modeling in China and other countries in East Asia.

Fungi play important roles in the process of material cycling and energy transfers in aquatic ecosystems. Yet little is known about the fungal community in lake sediment. In this study, sediment samples from five habitat types in Baiyangdian Lake (BYD Lake) were collected across three seasons. High-throughput sequencing techniques were used to determine the compositions of fungal communities. Fungi are highly diverse in the sediment of BYD Lake, although some important fungi have not been accurately identified. The fungal diversity was highest in winter and lowest in summer, while the variations of species richness among sampling sites were not significant. The compositions of fungal community differed among seasons and habitats. Physicochemical properties of sediments were measured and the influence of the environmental factors on fungal communities were analyzed. Temperature, P, N, and heavy metals explained 48.98% of the variations of fungal communities across three seasons. Human activities have affected the species and biomass of fungi to some extent. Temperature is the most influential factor and is negative to fungal diversity. Nutrient element in different forms have different effects on shaping the fungal community. The effect of heavy metals is not clear.

Crop production in Afghanistan suffers from limited phosphorus (P) availability, which severely hinders national agriculture sustainability. This present study hypothesized that deep fertilizer placement could significantly enhance uptake of immobile P and thus tissue P accumulation and crop yield. A two-year pot experiment growing two maize (Zea mays) hybrid cultivars (Xida-789 and Xida-211) was therefore conducted to test these hypotheses under three contrasting fertilizer placement methods (broadcast, side band, and deep band). In doing so, P concentrations in both maize tissues and soils were compared at 45, 60, and 115 days after sowing (DAS) under nine combinations of nitrogen (N) and P fertilizer rates (kg ha-1: N112P45, N112P60, N112P75, N150P45, N150P60, N150P75, N187P45, N187P60, N187P75). Results have shown that deep band placement significantly increased P uptake efficiency, leading to greater P concentration and accumulation in maize tissues compared to other two fertilization methods. This improved P uptake was attributed to several factors associated with deep placement, including reduced P fixation, enhanced root access to P, and moisture availability for P uptake. Additionally, deep band placement combined with higher N application rates (N187 and N150) further enhanced plant P uptake by promoting P availability and utilization mechanisms. Deep band placement also resulted in significantly higher total soil P, Olsen-P, and P use efficiency than broadcast and side band methods, indicating a more efficient P fertilization strategy for maize that can improve growth and yield. This present study also found positive correlations between P concentration in plant organs and soil Olsen-P, highlighting the importance of adequate soil P levels for optimal plant growth. Overall, our results have showed that deep band fertilizer placement emerged as a superior strategy for enhancing P uptake efficiency, utilization, and maize productivity compared to broadcast and side band placement. This approach can potentially optimize P fertilizer utilization, improve maize growth and yield, while minimizing environmental P losses associated with broadcast applications.

Conditions under which compositions of component systems form a well-defined system-of-systems here are formulated at a fundamental level. Statement of what defines a well-defined composition and sufficient conditions guaranteeing such a result offers insight into exemplars that can be found in special cases such as differential equation and discrete event systems. For any given global state of a composition, two requirements can be stated informally as: 1) the system can leave this state, i.e., there is at least one trajectory defined that starts from the state, and 2) the trajectory evolves over time without getting stuck at a point in time. Considered for every global state, these conditions determine whether the resultant is a well-defined system and if so, whether it is non-deterministic or deterministic. We formulate these questions within the framework of iterative specifications for mathematical system models that are shown to be behaviorally equivalent to the Discrete Event System Specification (DEVS) formalism. This formalization supports definitions and proofs of the afore-mentioned conditions. Implications are drawn at the fundamental level of existence where the emergence of a system from an assemblage of components can be characterized. We focus on systems with feedback coupling where existence and uniqueness of solutions is problematic.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

Using numerical simulation method, combined with the pre-branch material characteristics of the measurement results, based on the LS-DYNA software to simulate the branch crushing process, the analysis found that not only the existence of the cutter cutting in the branch destruction process, there is also the cutting of the opposing surface of the bending fracture, with the increase in the speed of the knife rollers, the cutter cutting resistance increases, the cutting resistance reaches 2690 N when the cutter at 2500 r/min, the cutter cutting resistance is the smallest in the cutting simulation at the blade angle of 55°, the blade angle is more suitable for the cutting of the branch. In the cutting simulation under different cutting edge angles, the cutting resistance of the tool is the smallest when the edge angle is 55°, which is 1860 N. This edge angle is more suitable for branch crushing and cutting. Using Fluent software to analyse the airflow characteristics of the crushing device, it was found that with the increase of the knife roller speed, the inlet flow and negative pressure of the crushing chamber are increasing, the speed of 2500 r/min, the inlet flow and negative pressure were 1.92 kg/s and 37.16 Pa, which will be conducive to the feeding of branches, but the speed is too high and it will also lead to the enhancement of the vortex of part of the area in the crushing device, which will affect the feeding of branches and the throwing of the crushed material. affect the feeding of branches and the throwing out of crushed materials, and finally determined the speed range of the crushing knife roller is 1800 ~ 2220 r/min. Based on ANSYS/Model module modal analysis of the crushing knife roller, the knife roller of the first six orders of the intrinsic frequency and vibration pattern, crushing knife roller of the lowest order of the modal intrinsic frequency of 137.42 Hz, much larger than the crushing knife roller operating frequency of 37 Hz, the machine will not resonate during operation.

The origin of a product, consumer familiarity, and purchasing identity are factors that affect perception of cheese consumption. The present study aims at identifying consumers’ conceptualizations and attitudes towards local Greek cheeses of the North-Aegean Sea islands, such as Ladotyri, Graviera, Kasseri, Kaskavali, Melichloro, and Kalathaki, some of which have a Protected Designation of Origin (PDO) status, as opposed to cheeses of non-Greek origin, such as Cheddar, Regatto, and Gouda. Sensory and emotional attributes of local, local PDO, and imported cheeses, and drivers associated with consumers’ choice and acceptance above and beyond their sensory attributes were studied, using three methods: a) Flash Profile to gain insight into the sensory positioning of products and description of samples, b) qualitative analysis of focus groups to pinpoint consumer knowledge, preference, and consumption criteria, and c) a new methodology for natural language processing and sentiment analysis of social media posts to determine consumer conceptualizations. Social media posts have proven to be a valuable source of linguistic and cultural data for cheeses. Local cheeses, including PDO products, were found to be linked to village life and family gatherings, home, tradition, and childhood memories, with saltiness and hardness being their main sensory attributes. Imported cheeses were linked to fast food, pizza, and snacking, with elasticity and gumminess as prominent sensory qualities. The main criterion of purchase was intended usage and versatility, taste and texture, price, and familiarity. The findings provide key sensory attributes, information about consumer purchasing criteria, and relevant vocabulary for the promotion of cheeses as agri-food and gastronomic identity key products.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

Ti-Al based alloys, particularly TiAl and Ti3Al two-phase alloys, have garnered significant attention as potential replacements for various high-temperature structural materials due to their exceptional properties, including low density, oxidation resistance, and high strength at elevated temperatures. Despite these advantages, experimental studies on the microstructure evolution of Ti-Al based alloys under complex conditions remain challenging to observe and characterize. This review article examines the current research on molecular dynamics (MD) simulations of Ti-Al based alloys, focusing on two-phase Ti-Al alloys, Ti-Al amorphous alloys, Ti-Al composite materials, and the welding and multi-layer/film applications of Ti-Al alloys. The review highlights the unique capabilities of MD simulations in predicting the behavior of Ti-Al based alloys and addresses existing scientific challenges. Furthermore, the article discusses future research directions and development prospects in this field.

The development of virtual models has recently been generalized in the field of complex mechatronic product design. Virtual models have various advantages such as: the systemic design approach, most often parametric, the implementation of extreme, expensive, and perhaps risky scenarios for the operation of the designed product, the testing of a large number of variants, etc. The main contribution of the paper consists of the development of an interface family called DeSeRoI (Dedicated Serial Robot Interface). Each member of the interface family integrates Simulink libraries and is created by the programmer in accordance with user requests. It follows that the interfaces composing the DeSeRoI family can have different levels of complexity depending on user needs and constraints. We are implementing a MATLAB-based application with user-provided configuration for serial robots in order to automatically visualize the kinematics data and simulation. Within MATLAB, two scripts are created responsible for generating Simulink models that compute the kinematics problem. One of the scripts (Main) saves information about the configuration of the robot and the other one (Generates_Simulink_Models) computes the kinematics problem. Different types of functions (software module) have been developed. Using these functions, the Simulink models result as modular entities. The automated approach eases user’s interaction and understanding of serial robots’ kinematics by performing the simulation procedure in a shorter amount of time and with higher efficiency, assuring a precise outcome despite the chosen parameters.

This study examines geothermal energy extraction potential from the basement rock within the Denver-Julesburg (DJ) Basin, focusing on flow performance and heat extraction efficiency of different geothermal well configurations. It specifically compares U-Shaped, V-Shaped, Inclined V-Shaped, and Pipe-in-Pipe configurations against Enhanced Geothermal Systems (EGS) setups. Through numerical modeling, we evaluated the thermal behavior of these systems under various operational scenarios and fracture conditions. Results suggest that while closed-loop systems offer moderate temperature increases, EGS configurations show substantial potential for high-temperature extraction. This underscores the importance of evaluating well configurations in complex geological settings like the DJ Basin. The insights from this study aid in strategic geothermal energy planning and development, marking significant advancements in geothermal technology and setting a foundation for future explorations and optimizations.

Driven by the growing interest of the scientific community and the proliferation of research in this field, cranial implants have seen significant advancements in recent years regarding design techniques, structural optimisation, appropriate material selection and fixation system method. Custom implants not only enhance aesthetics and functionality but are also crucial for achieving proper biological integration and optimal blood irrigation, critical aspects in bone regeneration and tissue health. This research aims to optimize the properties of implants designed from triply periodic minimal surface structures. The gyroid architecture is employed for its balance between mechanical and biological properties. Experimental samples were designed varying three parameters of the surface model: cell size, isovalue and shape factor. Computational simulation tools were used for determining the relationship between those parameters and the response variables: the surface area, permeability, porosity and Young modulus. These tools include computer aided design, finite element method and computational fluid dynamics. With the simulated values, the corresponding regression models were fitted. Using the NSGA-II, a multi-objective optimisation was carried out, finding the Pareto set which includes surface area and permeability as targets, and fulfil the constraints related with the porosity and Young modulus. From these non-dominated solutions, the most convenient for a given application was chosen, and an optimal implant was designed, from a patient computed tomography scan. An implant prototype was additively manufactured for validating the proposed approach.

In this paper we report a new development on the numerical model for aluminum-steam combustion. This model is based on diffusion flame of continuum regime and the thermal equilibrium between the particle and the flow field, which can be used to calculate the aluminum particle combustion model for two phase calculation conditions. The model prediction is in good agreement with the experimental data. A new type of vortex combustor was proposed for the combustion of aluminum and steam, and the mathematical model of the two phase reacting flow with in this combustor was established. The turbulence effects are modeled using the Reynolds Stress Model (RSM) with Linear Pressure-Strain approach, and the Eddy-Dissipation model is used to simulate the gas phase combustion. Aluminum particles are injected into the vortex combustor and form a swirling flow around the chamber and their trajectories are traced using the Discrete Phase Model (DPM). The simulation results show that the vortex combustor can achieve high efficient combustion of aluminum and steam. The influencing factors, such as the eccentric distance of the inlet of aluminum particles, particle size and steam inlet diameter, etc., are studied. The work described in this paper represents an attempt to the design of a vortex combustor in order to increase aluminum combustion efficiency.

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

The majority of existing numerical simulations of the effect of bridge piers on water movement are based on a limited number of bridge piers at a laboratory scale. Furthermore, some 2D numerical simulations for actual bridge projects have deficiencies, including the use of overly large mesh sizes and an inadequate treatment of bridge piers. In this study, we compare three methods of structural mesh encryption, suspension mesh, and nonstructural mesh based on Delft3D, and apply the optimization scheme to a real bridge project. It is demonstrated that optimal results can be achieved by utilising a grid size comparable to the pier diameter (Dp) in the region away from the piers. In the vicinity of the piers, the grid cell size should be no larger than 1/9 Dp. The suspended grid technique (DD Boundary) can yield results consistent with those obtained using a full-area high-resolution grid, provided that the total number of grids can be reduced and the computational time is considerably reduced. In this study, the unstructured mesh (Deflt3D Flexible Mesh) scheme was unable to capture the oscillations of the wake flow behind the bridge piers. However, the application of the optimized scheme in bridge engineering has demonstrated its practical value. The findings of this study on mesh resolution and suspension mesh scheme can be applied to the Delft3D software and are also useful for other numerical simulation work.

Questionnaires for self-report of food-elicited emotions are an established practice in consumer studies. However, most tools are originally developed in English and translated into other languages, which limits their use. The aim of this study was to develop the first Greek emotion lexicon and measurement tool for consumers, using standard methodology and extending it. The lexicon was compiled using linguistic sources and extended using the World Wide Web and a popular social media platform for the collection of authentic language and usage data. Terms were also collected from consumers using questionnaires and a variety of stimuli. Terms collected from consumers only comprise: healthy, distrustful, curious, childish, impressed, tolerant, impatient It was validated by application in various case studies, providing discrimination across and within food categories, and by comparison to the Greek translation of a standard tool in English, the EsSense Profile. The comparison was conducted by measuring emotions elicited by six food categories and demonstrated that it is preferable to use emotion measurement tools developed in the linguistic and cultural context of intended use, as they convey consumers’ emotions naturally and more accurately. This tool can be used as a Check- or Rate- All-That-Apply questionnaire to measure consumer responses to food categories and products. The methodology and validation presented can be applied for the compilation of emotion lexicons in languages less studied than English.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

The control of the fine particle emission from the coal-fired power plants has been a big challenge in china. Either the conventional electrostatic precipitator or the fabric filter has some shortages. The electrostatic precipitator is hard to keep high efficiency for the submicron particles. The fabric filter could keep high efficiency but with very high pressure drop. One solution is to combine them together. Several types of hybrid particle collectors (HPC) combining the electrostatic precipitator and the fabric filter together have been developed and applied in a number of projects in China. In recent years, numerical simulation technology has been widely used in the design of the collectors. In this paper, an unsteady numerical model is used to investigate the particle deposition characteristics in a scale hybrid collector. The fluid field is modeled by using incompressible Navier-Stokes equations with the RNG turbulence equations. The corona discharge is solved by using a finite volume method. The particle charging is modeled by using a filed-diffusing combined model. And an unsteady cake formation model is used to simulate the filtration process.

This paper presents a biologically inspired flocking-based aggregation behaviour of a swarm of mobile robots. Aggregation behaviour is essential to many swarm systems, such as swarm robotics systems, in order to accomplish complex tasks that are impossible for a single agent. We developed a robot controller using Reynolds’ flocking rules to coordinate the movements of multiple e-puck robots during the aggregation process. To improve aggregation behaviour among these robots and address the scalability issues in current flocking-based aggregation approaches, we used a K-means algorithm to identify clusters of agents. Using the developed controller, we simulated the aggregation behaviour among the swarm of robots. Five experiments were conducted using Webots simulation software. The performance of the developed system was evaluated under a variety of environments and conditions, such as various obstacles, agent failure, different numbers of robots and arena sizes. The results of the experiments demonstrated that the proposed algorithm is robust and scalable. Moreover, we compared our proposed algorithm with another implementation of the flocking-based self-organizing aggregation behaviour based on Reynolds’ rules in a swarm of e-puck robots. Our algorithms outperformed this method in terms of cohesion performance and aggregation completion time.

Molten salt electrolysis stands as an indispensable technique for the production of rare earth metals, where the judicious distribution of the electric field within the electrolytic cell is paramount for ensuring the seamless operation of the electrolysis process. This study introduces a pioneering approach by integrating the Nernst-Planck equation with the Butler-Volmer equation, thereby devising a holographic electric field model tailored for the electrolysis of the NdF3-LiF molten salt system. The paper presents pioneering experimental measurements concerning the potential distribution and voltage drop characteristics within a 6kA rare earth electrolytic cell, elucidating the interplay between decomposition voltage and current density, which substantiates the model's precision. Our findings unveil that, under operational conditions of 4010 amperes, the 6kA electrolytic cell incurs a total voltage drop of 6.3 volts, delineating a melt voltage drop of 4.43 volts, an ohmic voltage drop of 0.248 volts, and an interfacial voltage drop of 1.622 volts at the electrode-electrolyte junction. The discrepancy in error is confined to within 0.3% of the actual measured voltage of 6.28 volts.The simulation outcomes from the holographic electric field model have been confirmed to precisely and comprehensively reflect the characteristics of the electric field distribution during the rare earth molten salt electrolysis process, offering valuable theoretical insights for practical manufacturing applications.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

Nowadays, rotor-stator mixers are widely used in the chemical process industry to carry out the dispersion and de-agglomeration processes for manufacturing the homogenous electrode slurries. Development of the process simulation models for the turbulent mixing of these slurries helps to optimize the mixing parameters such as rotational speed and dispersion time. In this work, computational fluid dynamics (CFD) approach through ANSYS Fluent are explored to determine and analyze the flow patterns, velocity fields and viscosity distribution during the dispersion of anode slurries. It utilizes a non-homogeneous Eulerian multiphase approach and the typical k-ε model to create turbulence fields and compute the mixing rate. This work significantly improves our understanding of the relationship between rotor speed, dispersion time, viscosity distribution, and mixer geometry in rotor-stator mixers.

Shear dynamics simulation under extreme pressure was used to optimise the composition of ester-based lubricant base oil and extreme pressure additives. As a result, the ester-based lubricant in the weak-gel drilling fluid achieves reduction and increases the efficiency in drilling construction, and the field operation efficiency improves. The results of base oil lubrication simulation show that three base oils, namely, methyl oleate, ethyl oleate and butyl oleate, can be stably adsorbed on the surface layer of the shear surface. Methyl oleate has the lowest system temperature after shear stabilisation and has a high load-bearing capacity. The shear stress of methyl oleate decreases by changing the initial shear temperature and speed. It increases by 6.36 MPa when the speed increases from 10 m/s to 30 m/s. At this time, the shear stress of butyl oleate increases by 10.11 MPa. The results of the four-ball friction experiments show that the radius of the abrasion spot of methyl oleate is 179.83 μm, which is smaller than that of the other two base oils. Moreover, the friction coefficient of methyl oleate is 0.0018, which is approximately 1/3 of that of butyl oleate. Methyl oleate has better lubrication efficiency. The shear simulation results are consistent with the experimental results. The simulation can be used for the molecular design of lubricant materials. The oleic acid amide–containing amine group and the glyceride oleic–containing hydroxyl group were selected as the extreme pressure functional components for shear simulation. Results show that the shear stress of oleic acid amide is much lower than that of oleic acid glyceride when the initial shear temperature and speed change. The extreme pressure lubrication component–containing amine group is better than the extreme pressure lubrication material–containing hydroxyl group. The effects of different oleamide contents in the two-component mixtures on the lubricating properties were investigated through shear simulation, with methyl oleate as the base oil and oleamide as the extreme pressure functional component. The simulation results show that the lubricant has the optimal shear stress when 10% oleamide is added to the lubricant. The base properties of the lubricant were tested using a mixture of 90% methyl oleate and 10% oleamide, formulated as a lubricant. Results show that the friction coefficient can be reduced to 0.03 when 0.5% of the lubricant is added to the base mud. Moreover, the lubricant film formed shows high strength. Then, 1% lubricant was added to the weak-gel drilling fluid to evaluate the effect of the lubricant on the gel structure of the drilling fluid. Results show that adding lubricant does not affect the rheological properties of the drilling fluid. The gel structure of the system also remains stable even after 7 days of continuous ageing. The results of the field experiments in Hua3-01 well show that adding 1% ester-based lubricant to the field drilling fluid reduces the drilling friction by 33%. Thus, the efficiency of directional side drilling can be effectively improved, complicated accidents, such as poor starting and stopping of drilling and stuck jamming, can be avoided, and the goals of reducing quantity and increasing efficiency can be completed.

Two coupled climate models which participated the CMIP6 project (Coupled Model Intercomparison Project Phase 6), the Earth System Model of Chinese Academy of Sciences version 2 (CAS-ESM2-0) and the Nanjing University of Information Science and Technology Earth System Model version 3 (NESM3), were assessed in terms of the impact of four new sea ice parameterization schemes. These four new schemes are related to air-sea heat flux, radiation penetration and absorption, melt ponds, ice-ocean flux, respectively. To evaluate the effectiveness of these schemes, key sea ice variables with and without these new schemes, such as sea ice concentration (SIC) and sea ice thickness (SIT), were compared against observation and reanalysis product from 1980 to 2014. The simulations followed the design of historical experiments within the CMIP6 framework. The results revealed that both models demonstrated improvements in simulating Arctic SIC and SIT when the new parameterization schemes were implemented. The model bias of SIC in some marginal sea ice zones of Arctic was reduced, especially during March. The SIT was increased and the transpolar gradient of SIT was reproduced. The changes of spatial pattern of SIC and SIT after adding new schemes bear similarities between the two coupled models. This suggests that the new schemes have potential for broad application in climate models, especially for those with underestimated SIT.

Maintaining the optimal microclimate in broiler houses is crucial for bird productivity, yet enabling efficient temperature control remains a significant challenge. This study developed and validated a computational fluid dynamics (CFD) model to predict temporal changes in indoor air temperature in response to variable ventilation operations in a commercial broiler house. The model accurately simulated air velocity and airflow distribution for different numbers of tunnel fans in operation, with air-velocity errors ranging from -0.22 to 0.32 m s-1. The predicted airflow rates through inlets and cooling pads showed good agreement with measured values with an accuracy of up to 108.1%. Additionally, the CFD model effectively predicted temperature dynamics, accounting for chicken heat production and ventilation effect. The model successfully predicted the longitudinal temperature gradients and their variations during ventilation cycles, validating its reliability through comparison with experimental data. The study also explored different variable inlet configurations to mitigate the temperature gradient. The variable inlet adjustment showed the potential to relieve the high temperatures but may reduce overall ventilation efficiency or intensify temperature gradients, which confirms the importance of optimising ventilation strategies. This CFD model provides a valuable tool for evaluating and improving ventilation systems and contributes to enhanced indoor microclimates and productivity in poultry houses.

Modern automotive systems should must satisfy strict reliability requirements. Most of the real vehicle systems and safety-critical networks have complex interconnections. Sensitivities and probabilistic uncertainties of reliability of System with Complex Interconnections (SwCI) can be investigated by the Monte-Carlo Simulation (MCS). The paper focuses on sensitivities and parametrical uncertainties of SwCIs reliability. The proposed method can be used forimplemented in the investigation of uncertainties of SwCIs reliability – in other wordsi.e., for in the determination of critical system elements and to estimateion of the Required Number of Spare Parts (RNSP) of the system, which depends on the probability of allowable spare equipment shortage.

This study presents the design and comprehensive 3D multiphysics simulation of a novel microfluidic immunosensor for real-time, non-invasive monitoring of pro-inflammatory biomarkers in human sweat. The patch-like device, designed using COMSOL Multiphysics, integrates magnetofluidic manipulation with direct-field capacitive sensing. The sensor comprises two distinct units: an immunocomplex enhancement unit, employing a series of microcoils to optimize the binding efficiency, reaction kinetics, and homogeneity of biomarker-magnetic nanoparticle (MNP) interactions, thereby enhancing the sensor's specificity; and a layered capacitive sensing unit, designed to concentrate and detect biomarker-tagged MNPs, thus amplifying sensitivity. Simulations of the capacitive sensing unit revealed a substantial sensitivity increase of up to 42.48\% at an 85\% MNP concentration within the detection zone. These findings highlight the potential of the proposed immunosensor for efficient and precise real-time biomarker monitoring, which may facilitate early disease diagnosis and enable personalized healthcare interventions.

Advanced Finite Element (FE) modeling and simulations were performed on vehicular crashes into a Three-bar Metal Bridge Rail (TMBR). The FE models of a sedan, a pickup truck, and a TMBR section were adopted in the crash simulations subject to Manual for Assessing Safety Hardware (MASH) Test Level 2 (TL-2) and Test Level 3 (TL-3) requirements. The test vehicle models were first validated using full-scale physical crash tests conducted on a two-bar metal bridge using a sedan and a pickup truck with similar overall physical properties and sizes to their respective vehicles used in the simulations. The validated vehicular models were then used to evaluate the crash performance of the TMBR using MASH Evaluation Criteria for structural adequacy, occupant risk, and post-impact trajectory. The TMBR met all MASH TL-2 requirements but failed to meet the MASH TL-3 Criteria H and N requirements when impacted by the sedan. The TMBR was also evaluated under in-service conditions (behind a 1.52-m wide sidewalk) and impacted by the sedan under MASH TL-3 conditions. The simulation results showed that the TMBR behind a sidewalk met all safety requirements except for the occupant impact velocity in the longitudinal direction, which exceeded the MASH limit by 3.93%.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

The fractional advection-dispersion equation FADE plays an important role, especially in explaining the process of solute-transport in natural porous media with different degrees of heterogeneity. However, studies of the flow and transport of contaminants in the underground environment are based on the knowledge of many functional parameters of the subsoil. The delay factor caused by nonlinear absorption is one of these parameters inheriting significant ambiguities in its estimation in heterogeneous media. In the study, a fractional advection-dispersion FADE model was developed by the implicit Euler method, based on a Grunwald and Caputo-Liousville approximation to explicitly evaluate and simulate the transport mechanism of contaminants in media with unsaturated porous materials subjected to a nonlinear sorption model. Better solute mass retention was observed for fractional advection-dispersion FADE model. Moreover, the absorption parameter of the retardation coefficient has a better impact on the motion of the solute in a saturated porous medium. In other words, it has a significant effect on the dispersion of pollutants in aquifers. This study highlights the need to characterize the aquifer to predict solute transport in porous media.

Addressing the significant challenge in high-speed cotton dibbling operations in Xinjiang—specifically, the duck bill’s ("Duck bill" is a type of duck-billed bunch planting mechanism or component). shortened opening duration leading to seed throwing and floating—a new crawler-type delayed hole-forming mechanism has been designed. This mechanism extends the duck bill horizontally, thereby prolonging its opening time, enabling cotton sowing speeds of up to 6 km/h. Following agronomic principles for cotton planting, the overall layout of the crawler-type hole-forming mechanism, the structural parameters of the key components and the trajectory of the hole-forming are determined. We use the Discrete Element Method (DEM) and multi-body dynamics coupling method to simulate and analyze the motion process of the device. The fixed the tilt angle of the duck bill α(A), the depth of the duck bill hole-forming into the soil h(B), and the angle of rotation of the moving duck bill β(C) were taken as the experimental factors, with the longitudinal length of cotton seed hole (Y1) and the hole-forming depth of cotton seed hole (Y2) as the response values. The parameter range of each factor and the preliminary influence on the response value were determined through pre-experiments and single-factor simulation test. Based on RecurDyn-EDEM coupling, a quadratic regression orthogonal rotation combination simulation test was carried out. The results show that the order of the primary and secondary factors affecting the Y1 of the time-lapse hole-forming device was: A > C > B. The order of primary and secondary factors affecting the Y2 of the delayed hole forming device was: B > C > A. When the A was 2.4 °, the B was 42.4 mm, and the C was 30.5 °, the performance of the hole-forming was the best, and the Y1 was 26.4 mm, and the Y2 was 25.0 mm. The bench verification test results show that under the optimized combination of operating parameters, the average Y1 was 29.1 mm, and the average Y2 was 23.2 mm. Compared with the results of the previous coupled simulation model, the average relative errors of the two are 7.23 % and 4.36 %, respectively, indicating the accuracy and effectiveness of the established DEM simulation model and virtual test analysis. The hole-forming area and the opening time of the duck bill after the stable operation of the machine were recorded and measured. The calculated hole dislocation rate Hc was 4.33 %, which did not exceed the national standard requirement of 6 %. The qualified rate of hole distance Hx was 94.33 %, which was much higher than the national standard requirement of 80 %. The average opening time of the duck bill at a speed of 6 km/h is 0.45 s, which is much longer than the time required for cotton seeds to fall from the duck bill 0.11 s. It meets the requirements of high-speed cotton planting in China and facilitating advancements in future high-speed planter technology.

A novel approach to optimizing turbomachinery performance is presented in this chapter, which integrates Computational Fluid Dynamics (CFD) simulations, an artificial neural network (ANN) with a modified Non-dominated Sorting Genetic Algorithm II (NSGA-II). Using this enhanced algorithm, substantial performance improvements can be achieved through geometric optimization. The effectiveness of this method is demonstrated in two case studies: an inducer for a centrifugal pump and a Savonius wind turbine. The inducer is designed to maximize head coefficient, hydraulic efficiency, and net positive suction head by optimizing factors such as inlet and outlet blade angles. The optimization process employs the Group Method of Data Handling (GMDH) for objective function modeling, followed by Pareto front plotting and TOPSIS for identifying trade-off optimal points. Results indicate significant improvements in head coefficient, hydraulic efficiency, and NPSHR by 14.3%, 0.3%, and 30.2%, respectively. Twist angle, aspect ratio, and overlap ratio are also optimized for wind turbine blades. The power coefficient is enhanced by 5.32%, the torque coefficient by 13.74%, and the rotational speed by 0.071% through multi-objective optimization. As a result of this approach, efficiency improves, and valuable insights into the optimal design principles for turbomachinery components are also gained.

The shear stress generated by wall turbulence is the main cause of wall friction resistance in turbulent flow through pipes. This paper investigates the impact of inserting rest periods (regions of constant Reynolds number) within the pulsating operating cycle of velocity on the fully turbulent flow at large time-averaged Reynolds numbers, using the Large Eddy Simulation (LES) method. The study aims to explore the effect of increasing rest periods within pulsations on drag resistance. The dimensionless shear stress and drag reduction rates during different time periods of rest were analyzed. Numerical simulation results indicate that the pulsating velocity operation mode does not necessarily lead to drag reduction; it may even result in increased resistance. Inserting rest periods within the pulsation cycle can achieve drag reduction effects, with the maximum drag reduction rate reaching 21.8\%. Comparisons with experimental data and Direct Numerical Simulation (DNS) from the literature validate the feasibility of using the LES method for pipe pulsating operation modes.

This paper proposed a three-layer distributed simulation network architecture: 1. Distributed virtual simulation network, 2. Perception and control sub-network, and 3. Collaborative communication service network. This simulation architecture runs on a distributed platform. The platform can provide a unique virtual scenario and several simulation services to verify the individual robot system's basic perception, control, and planning algorithms and the distributed collaborative algorithms of heterogeneous multi-robot systems. Furthermore, we designed a simulation experiment scenario for classical heterogeneous robot systems such as unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs). At last, We gave a rough estimation model of the bandwidth.

Tinnitus is a common phantom auditory percept, believed to be related to plastic changes in the brain due to hearing loss. However, tinnitus can also occur in absence of any clinical hearing loss. Then, since there is no hearing loss, the mechanisms that drive plastic changes remain largely enigmatic. Previous studies showed subtle differences in sound-evoked brain activity associated with tinnitus in subjects with tinnitus and otherwise, normal hearing, but the results are not consistent across studies. Here, we aim to investigate those differences using monaural rather than binaural stimuli. Sound-evoked responses were measured using functional magnetic resonance imaging (MRI) in participants with and without tinnitus. All participants had clinically normal audiograms. The stimuli were pure tones with frequencies between 353 and 8000 Hz, presented monaurally. A Principal Component Analysis (PCA) of the response in the auditory cortex revealed no difference in tonotopic organization, which confirmed earlier studies. A GLM analysis showed hyperactivity in the lateral areas of the bilateral auditory cortex. Consistent with the tonotopic map, this hyperactivity mainly occurred in response to low stimulus frequencies. This may be related to hyperacusis, which was associated with tinnitus found in the parahippocampus. This may reflect an interference between tinnitus and spatial orientation.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

In this work, two plasmonic structures with two different periodic nanostructures (nanodisk and nanostrip arrays) separated from the gold layer by an ultrathin dielectric Al2O3 layer are proposed, and their optical properties are simulated as 3-dimensional models using COMSOL Multiphysics software tool. The optical responses, such as the amplification of the electric field and the scattering, absorption and extinction cross sections of the two structures, are investigated and compared. The results show that both structures show strong field enhancement in their gap layer, and the structure with the periodic array of metal nanodisks shows stronger field enhancement and larger absorption, extinction, and scattering cross sections in its dipole resonance wavelength, which is defined as a bright plasmonic mode. In addition, some weaker resonant modes are observed for both structures and the reason for their generation is dis-cussed. The analysis of different possible modes in such structures is crucial for their application in various fields.

Although, promotion of urbanization culture in recent decades has made inevitable development of cities in the world, however, the development can be guided in a direction that leave, to the extent possible, minimum socioeconomic and environmental impacts. For this, it is required to first forecast auto-spreading orientation of cities and suburbs in rural areas over time and then avoid shapeless growth of cities. This paper is an attempt to develop a dynamic hybrid model based on logistic regression (LR), Markov chain (MC), and cellular automata (CA) for prediction of future urban sprawl in fast-growing cities. The model was developed using 12 widely-used urban development criteria, whose significant coefficient was determined by logistic regression, and validated by relative operating characteristic (ROC) analysis. The validated model was run in Guilan, a tourist province in northern Iran with a very high rate of urban development. For this, changes in the area of urban land use were detected over the period of 1989 to 2013 and then, future sprawl of the province was forecasted by the years 2025 and 2037. The analysis results revealed that the area of urban land use was increased by more than 1.7 % from 36012.5 ha in 1989 to 59754.8 ha in 2013, and the area of Caspian Hyrcanian forestland was reduced by 31628 ha. The results also predicted an alarming increase in the rate of urban development in the province by the years 2025 and 2037, during which urban land use is predicted to develop 0.9 % and 1.38 %, respectively. The development pattern is expected to be uneven and scattered, without following any particular direction. The development will occur close to the existing or newly-formed urban basements as well as around major roads and commercial areas. This development, if not controlled, will lead to the loss of 13863 ha of Hyrcanian forests and if the trend continues, 21013 ha of Hyrcanian forests and 20208 ha of Barren/open lands are expected to be destroyed by the year 2037. In general, the proposed model is an efficient tool for the support of urban planning decisions and facilitates the process of sustainable development of cities by providing decision-makers with an overview on future development of cities where the growth rate is very fast.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

In this paper, the boiling flow inside a nanochannel with 700000 argon particle has been simulated by molecular dynamics (MD) simulation. This approach has been employed to analysis the superheated flow and its heat transfer pattern as well. For all simulations an external thrust force varying from 1 PN to 12 PN is exerted on inlet nanoparticles along the channel to have the forced annular boiling flow. Computations reveal that saturation condition and superheat degree have significant impacts on the liquid-vapor interface. Furthermore, because of the major influence of surface tension throughout a nanochannel, the x-velocity of liquid film and vapor core has not considerable fluctuations and stay smooth. All provided results show the behaviors completely similar to the available outcomes in the literature.

Surgical simulators are crucial in early craniofacial and plastic surgical training, necessitating synthetic materials that accurately replicate tissue properties. Recent critiques of our lab’s currently deployed silicone surrogate have highlighted numerous areas for improvement. To further refine our models, our group's objective is to find a composition of materials that is closest in fidelity to native oral mucosa during surgical rehearsal by expert craniofacial surgeons. Fifteen platinum silicone-based surrogate samples were constructed with variable hardness and slacker percentages. These samples underwent evaluation of tactile sensation, hardness, needle puncture, cut resistance, suture retention, defect repair, and tensile elasticity. Expert craniofacial surgeon evaluators provided focused qualitative feedback on selected top-performing samples for further assessment and statistical comparisons. Evaluation revealed surrogate characteristics with satisfactory to good performance. Sample 977 exhibited the highest performance, and comparison with the original surrogate (sample 810) demonstrated significant improvements in critical areas, emphasizing the efficacy of the refined composition. The study identified a silicone composition that directly addresses the feedback received by our team’s original silicone surrogate. The study underscores the delicate balance between biofidelity and practicality in surgical simulation. The need for ongoing refinement in surrogate materials is evident to optimize training experiences for early surgical learners.

Surgical simulators are crucial in early craniofacial and plastic surgical training, necessitating synthetic materials that accurately replicate tissue properties. Recent critiques of our lab’s currently deployed silicone surrogate have highlighted numerous areas for improvement. To further refine our models, our group's objective is to find a composition of materials that is closest in fidelity to native oral mucosa during surgical rehearsal by expert craniofacial surgeons. Fifteen platinum silicone-based surrogate samples were constructed with variable hardness and slacker percentages. These samples underwent evaluation of tactile sensation, hardness, needle puncture, cut resistance, suture retention, defect repair, and tensile elasticity. Expert craniofacial surgeon evaluators provided focused qualitative feedback on selected top-performing samples for further assessment and statistical comparisons. Evaluation revealed surrogate characteristics with satisfactory to good performance. Sample 977 exhibited the highest performance, and comparison with the original surrogate (sample 810) demonstrated significant improvements in critical areas, emphasizing the efficacy of the refined composition. The study identified a silicone composition that directly addresses the feedback received by our team’s original silicone surrogate. The study underscores the delicate balance between biofidelity and practicality in surgical simulation. The need for ongoing refinement in surrogate materials is evident to optimize training experiences for early surgical learners.

To address the requirements of sonar imaging, such as high receiving sensitivity, wide bandwidth, wide receiving angle, an AlN PMUT with an optimized ratio of 0.6 for the piezoelectric layer diameter to backside cavity diameter is proposed in this paper. A sample AlN PMUT is designed and fabricated with SOI substrate-based bulk MEMS process. The characterization test result of the sample demonstrates a -6 dB bandwidth of approximately 500 kHz and a measured receiving sensitivity per unit area of at 1.37 V/μPa/mm2, which significantly surpasses the performance of previously reported PMUTs. The -6 dB horizontal angles of the AlN PMUT at 300 kHz and 500 kHz are measured 68.30° and 54.24°, respectively. To achieve an accurate prediction of its characteristics when being packaged and assembled in a receive array, numerical simulations with the consideration of film stress are conducted. The numerical result shows a maximum deviation of ±7% in the underwater receiving sensitivity across the frequency range of 200 kHz to 1000 kHz and a deviation of about 0.33% in the peak of underwater receiving sensitivity comparing to the experimental data. By such good agreement, the simulation method reveals its capability of providing theoretical foundation for enhancing the uniformity of the AlN PMUTs in future studies.

This study investigates the impact of vertical greenery systems (VGS) applied to heavyweight walls on indoor thermal conditions in a building module situated in the Mediterranean climate of Catania, Italy. Using dynamic simulations in TRNSYS, the research compares the thermal behavior of walls constructed from hollow clay blocks (Poroton) and lava stone blocks with a lightweight wall setup already in place at the University of Catania. The primary focus is on evaluating the VGS’s effect on reducing peak inner surface temperatures and moderating heat flux fluctuations entering the building. The findings indicate that adding a vertical greenery layer to heavyweight walls can decrease the peak inner surface temperature by up to 1.0°C compared to the same wall without vegetation. However, the greenery’s impact on mitigating heat flux fluctuations is less pronounced than in the case of the lightweight wall. This research underscores the potential of green facades in enhancing indoor thermal comfort in regions with climates similar to the Mediterranean, providing valuable insights for sustainable building design and urban planning.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

Hydraulic fracturing has enabled production from unconventional reservoirs in the U.S., but production rates often decline sharply, limiting recovery factors to under 10%. This study optimizes the CO2 huff-n-puff process for multistage-fractured horizontal wells in Wolfcamp A formation in the Delaware Basin. The potential for enhanced oil recovery and CO2 sequestration simultaneously was addressed using a coupled geomechanics-reservoir simulation. Geomechanical properties were derived from a 1D mechanical earth model and integrated into reservoir simulation to replicate hydraulic fracture geometries. The fracture model was validated using a robust production history matching. Fluid phase behavior analysis refined the equation of state, and 1D slim tube simulations determined a minimum miscibility pressure of 4300 psi for CO2 injection. After the primary production phase, various CO2 injection rates were tested from 1 to 25 MMSCFD/well, resulting in incremental oil recovery ranging from 6.3% to 69.3%. Different injection, soaking, and production cycles were analyzed to determine the ideal operating condition. The optimal scenario improved cumulative oil recovery by 68.8% while keeping the highest CO2 storage efficiency. The simulation approach proposed by this study provides a systematic workflow for evaluating and optimizing CO2 huff-n-puff in hydraulically fractured wells, enhancing the recovery factor of unconventional reservoirs.

: In this paper we present an optimization of the planar manufacturing scheme for stretch-free, shape induced metal interconnects to simplify the fabrication with the aim of maximizing the flexibility in the structure regarding to stress and strain. The Formation of trenches between silicon islands are actively used in the lithographic process to create arc shape structures by spin coating resist into the trenches. The resulting resist form is used as a template for the metal lines, which are structured on top. Because this arc shape is beneficial for the flexibility of these bridges. The trench depth as a key parameter for the stress distribution is investigated by applying numerical simulations. The simulated results show that the increase in penetration depth of the metal bridge into the trench increases the tensile load which is converted into a shear Force Q(x), that usually leads to increased strains the structure can generate. For the fabrication the filling of the trenches with resist is optimized by varying the spin speed. Compared to the theoretical resistance, the current-voltage measurements of the metal bridges show a similar behavior and almost every structural variation is capable of functioning as a flexible electrical interconnect in a complete island-bridge array.

This paper presents a study on developing of a new exoskeleton for ankle joint rehabilitation with three degrees of freedom (3 DOFs). The primary attention is paid to the process of designing and modelling the device aimed at restoring the lost functions of joint mobility. The authors carried out a complex analysis of the functional requirements of the exoskeleton based on the research of potential user’s needs, which allowed them to develop a conceptual model of the proposed de-vice. In this study, a prototype of the exoskeleton is designed using modern additive technolo-gies. A prototype of the proposed device underwent virtual testing in conditions maximally close to the real one, which confirmed its effectiveness and comfort of use. The main results of the work indicate the promising potential of the proposed solution for application in rehabilitation practice, especially for patients with ankle joint injuries and diseases.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

Decision sciences (DSC) involve studying complex dynamic systems and processes to aid informed choices subject to constraints in uncertain conditions. It integrates multidisciplinary methods, techniques, and strategies to evaluate decision engineering processes, identifying alternatives and providing insights towards enhancing prudent decision-making. This study analyzes the evolutionary trends and innovation in DSC education and research to uncover the transformations over the years. We employ the science mapping method, text analytics, and metadata from bibliographic databases to evaluate thematic and social structures. The results highlight data science methods, including data mining and business/learning analytics as essential components. The evolutionary trends in DSC education and research mirror the development in practice, including technological transformation, computer science advances, and engineering processes. Sustainable education through virtual/online learning also constitutes a significant component of scientific production. The evolutionary trends in DSC education and research highlight innovative pedagogical approaches and strategies, including computer simulation and games ('play and learn'). The current era witnessed generative artificial intelligence (GenAI) adoption (e.g., ChatGPT) in teaching, learning, and scholarly activities amidst challenges (academic integrity, plagiarism, intellectual property violations, and other ethical and legal issues). Future research will implement and integrate AI automatic detection systems to address some GenAI adoption challenges.

This study uses simulation and experimental methodologies to explore the efficacy of bi-sectional horizontal kinetic shading systems (KSS) featuring horizontal fins in enhancing daylight comfort across various climates. Given the increasing energy demands and shifting climatic patterns, optimizing daylight levels while minimizing solar heat gain is vital. The paper introduces a bespoke horizontal bi-sectional KSS, simulated in three distinct climates—Wroclaw, Tehran, and Bangkok—using Climate Based Daylight Modelling methods with Ladybug and Honeybee tools in Rhino software. The study employs standard daylight metrics such as Useful Daylight Illuminance (UDI) and Daylight Glare Probability (DGP), along with custom metrics designed to capture the specific dynamics of the bi-sectional KSS. Initial simulations indicated that the KSS significantly improved daylight distribution and uniformity, reducing glare and over-illumination risks by av. 42.34%. Including KSS switching schedules, which are seldom detailed in similar research, enhances the reproducibility and understanding of findings. Subsequently, a physical reduced-scale mock-up of the bi-sectional KSS was tested under real-weather conditions in Wroclaw (lat. 51° N) during June-July 2024. The mock-up utilized two chambers: one equipped with the prototype of bi-sectional KSS and the second without any protection. The operation of fins was guided by two stepper motors controlled by a Python script running on a Raspberry Pi 3 minicomputer. The control chamber served to benchmark the bi-sectional KSS's efficiency by providing results that would be expected if no shading system were installed. The experimental outcomes supported the simulations, demonstrating the KSS's robustness in reducing high illuminance levels to the target comfort level, thus enhancing indoor visual comfort. The values below 3,000 lux were maintained for 68% of the time. However, it must be explicitly stated that during the June-July 2024 heat waves, the illuminance levels inside the test room momentarily exceeded the comfort threshold of 3,000 lux, reaching up to 4,674 lux. Through quantitative and qualitative analyses, the paper advocates for the broader application and further development of KSS as a climate-responsive shading system in diverse architectural contexts.

Perovskite solar cells (PSCs) are vital for their optical and electrical properties, with lead-based PSCs reaching a remarkable efficiency of 26.1%, while tin-based counterparts achieve 18.71%. Due to lead's toxicity, there's a push for alternatives like tin. However, tin-based PSCs suffer from stability issues and high defect density states, necessitating the development of cost-effective, high-performance, and eco-friendly alternatives. In this study, we designed a hetero-junction architecture using MASnI3-based Perovskite, opti-mized with SCAPs-1D. After exhaustive analysis, our device achieved a power conversion efficiency of 24.18%, with enhanced parameters including Voc of 0.09323V, Jsc of 30.8360 mA/cm2, and FF of 84.10%. Recombination rates, particularly Shockley-Read Hall recom-bination, were significantly reduced. Parametric analyses, encompassing absorber layer thickness, band gap, defect density, doping concentration, and operating temperature, in-dicate potential efficiency enhancements. This underscores the viability of Sn-based PSCs as a cost-effective, efficient, and environmentally benevolent alternative to lead-based counterparts, promising advancements in future research and development efforts.

Agricultural greenhouse is largely answered in the agricultural sphere, despite the shortcomings it has, including overheating during the day and night cooling which sometimes results in the thermal inversion mainly due to its low inertia. The glasshouse dressed chapel is relatively more efficient than the conventional tunnel greenhouse. Its proliferation on the ground is more or less timid because of its relatively high cost[14-22]. Agricultural greenhouse aims to create a favorable microclimate to the requirements of growth and development of culture, from the surrounding weather conditions, produce according to the cropping calendars fruits, vegetables and flower species out of season and widely available along the year. It is defined by its structural and functional architecture, the quality thermal, mechanical and optical of its wall, with its sealing level and the technical and technological accompanying[12-13]. The greenhouse is a very confined environment, where multiple components are exchanged between key stakeholders and them factors are light, temperature and relative humidity[8]. This state of thermal evolution is the level sealing of the cover of its physical characteristics to be transparent to solar, absorbent and reflective of infrared radiation emitted by the enclosure where the solar radiation trapping effect otherwise called "greenhouse effect" and its technical and technological means of air that accompany. The socio-economic analysis of populations in the world leaves appear especially the last two decades of rapid and profound transformations These changes are accompanied by changes in eating habits, mainly characterized by rising consumption spread along the year[14]. To effectively meet this demand, greenhouse-systems have evolved, particularly towards greater control of production conditions (climate, irrigation, ventilation techniques, CO2 supply, etc ...). Technological progress has allowed the development of greenhouses so that they become increasingly sophisticated and of an industrial nature (heating, air conditioning, control, computer, regulation, etc ...). New climate driving techniques have emerged, including the use of control devices from the classic to the use of artificial intelligence[10-11] such as neural networks and / or fuzzy logic, etc... As a result, the greenhouse growers prefer these new technologies while optimizing the investment in the field to effectively meet the supply and demand of these fresh products cheaply and widely available throughout the year.

A better understanding of high temperature processes in slags contributes to facilitate knowledge based design of the solidified product. Here, a slag analogue with a nominal composition of 17 wt% LiMnO2 and 83 wt% Ca2SiO4 was synthesized encountering fairly high cooling rates. The Mn species from 1223 K to 1773 K was simulated using a thermodynamic model assuming a homogeneous melt. The micro-composition including the Mn species of the solidified slag was determined experimentally and was used as basis for molecular dynamics (MD) simulation. The MD simulation provides information on structure and viscosity at high temperatures, otherwise difficult to access. These parameters significantly influence oxidation state of redox-active elements and the solidified product. The micro-composition analyzed by electron probe micro analysis (EPMA) and synchrotron based micro-X-ray fluorescence (micro-XRF) showed that Mn-rich and Ca-Si-rich phases are separated. While the Mn-O phases did not contain noticeable Ca, the Ca2SiO4 phase had incorporated 0.6 wt% of Mn. The slag solidified into round shaped and droplet shaped grains of a Li-Mn-oxide, some Mn3O4 and Ca2SiO4. The powder X-ray diffraction (PXRD) confirmed the formation of larnite, the identity of the Li-Mn-oxide however remained inconclusive. The Mn oxidation state (OS) was identified using synchrotron based micro-X-ray absorption near edge spectroscopy (micro-XANES). The Mn-O grains, matched well with Li-Mn-oxides and a Mn OS: +3 e.g. LiMn3+O2. Small areas matching Hausmannite (Mn2+Mn23+O4) were also identified. The OS of Mn in the silicate phase could not be identified. For comparison a slowly cooled slag analogue with similar composition however higher Si content, was also subjected to micro-XANES. The slowly cooled slag formed long Mn-rich needles in a matrix of large calcium silicate crystals. The Mn-rich crystals matched well with the XANES spectrum of a Mn3+ Li-oxide like LiMn3+O2. At the rim of the needles the Mn-spectra matched well the Hausmannite (Mn2+Mn23+O4) reference. In the silicate phases Mn had a OS: +2, unambiguously. The melt structure at different temperatures of two compositions i.e. LiMn3+O2 and Ca2SiO4 was simulated using molecular dynamics (MD). They serve as model compositions assuming a heterogeneous melt. The results show significant different degrees of polymerization and viscosity. Information from MD simulations can support the identification of potentially different oxygen permeability and with that prediction of oxidation states. The bulk composition was identified by inductively coupled plasma optical emission spectrometry (ICP-OES), bulk structure by PXRD and bulk species by lab-XANES. The synchrotron micro analysis including micro-XRD were performed at the microfocus beamline I18 at the Diamond Light Source. Pure reference compounds were prepared and characterized with the same multi-modal approach.

The material properties and structural characteristics of ballistic composites are crucial to their ballistic performance. Investigation for the influence of the material and structural parameters of UHMWPE body armor on anti-fragmentation penetration performance has been made by numerical simulation in this paper, with a numerical modeling simulating the penetration of a 1.1 g FSP into the target plate of UHMWPE body armor, by which the simulation results demonstrate that the failure process of the body armor target plate primarily involves shear damage, interlayer delamination, and tensile damage. Furthermore, the study evaluates the effects of elastic modulus, tensile strength, shear strength, number of layers, and interlayer strength on the ballistic limit velocity of UHMWPE body armor. The findings reveal that the ballistic limit velocity is most sensitive to changes in shear strength, with variation rates ranging from -18.02% to 10.81%, showing an approximate positive correlation, while the elastic modulus has the smallest impact on ballistic limit velocity, with variation rates ranging from -1.8% to 3.6%. Additionally, appropriate interlayer strength can improve the ballistic limit velocity of the body armor to a certain extent. This study provides theoretical methods and recommendations for optimizing anti-penetration performance of UHMWPE body armor.

In this study, in order to determine the effect of matrices shape on percolation threshold values, computer simulations were performed using the Monte Carlo method for a 200x200 square-shaped matrix and rectangular matrices containing the same number of nodes as the square matrix. Based on the simulations, the average values of percolation thresholds and standard deviations for current flow along and across the matrices were determined. It was determined that for a square-shaped matrix, the average values of percolation thresholds in both directions of current flow were the same. Extending the rectangular matrix while reducing its height causes the average value of the percolation threshold in the direction of current flow along the matrix to increase from 0.592740 to 0.759847, while in the transverse direction it decreases from 0.592664 to 0.403614. The values of the classical asymmetry coefficients of the probability distributions of percolation thresholds for both directions of current flow were determined. Histograms of the probability distributions of percolation threshold values for square-shaped matrix and rectangular matrices were made and compared with normal distributions. It was found that the occurrence of two percolation thresholds in rectangular layers should be considered when analyzing electrical conductivity measurements of nanocomposite thin films.

The advanced industrial systems are characterized by complex event-driven processes. The specification and computer analysis are illustrated by the common problem of a servo drive with the PWM controller. A mathematical model from the class of Cauchy problems with non-liner control logic is presented to resolve the task discussed. The designed model is performed in two stages: the mathematical model specification (modeling) and implementation (simulation). Two approaches to make a model specification are considered, the first one is the traditional structural technique, and the advanced method is based on the finite state machine paradigm. Structural and finite state software models are built in progressive simulation tools. Computer implementation of the software models of hybrid systems is performed using platform built-in libraries with numerical methods and algorithms for correct event detection. The results of computational experiments for transient processes of phase variables are qualitatively identical, that proves the adequacy of the developed models. The algorithm for asymptotic event detection is considered in detail. This technique demonstrated the best results by the one-sidedness criterion, which is explained by using the author’s algorithm for the integration step determining and the event function dynamics monitoring in the vicinity of the event limits.

In the context of energy conversion from renewable sources to distribution grids (insulated or not), a converter is often required to transfer energy from a low voltage source, towards three-phase grids. This paper presents the HW design, the simulation results and the conversion performance of a CSI converter intended to interface low voltages renevable sources to three-phase grids. The main focus of this paper is to obtain the best performance in terms of voltage increase towards the output stage while maximizing the conversion efficiency. In comparison with the currently used energy conversion systems for small photovoltaic systems, hereafter some solutions were adopted to level and maximize the energy flow from the source to the DC-link and improve the quality of current supplied in terms of harmonic distortion. The proposed system is composed of two conversion stages: the first, voltage-to-current, the second current-to-current via a three-phase CSI bridge modulated with SVM technique. The stages are not completely decoupled from an electrical point of view, therefore, in order to mitigate the effects of these interactions, synchronization strategies have been adopted.

The object of study in the article is the auxiliary variable-frequency electric drive onboard of an AC electric locomotive, and more precisely, the structure and parameters of the control system of the active corrector of power factor (ACPF), which is part of the electric drive, as a unit that ensures electromagnetic compatibility of the electric drive with other equipment on board the electric locomotive and catenary and its energy efficiency. The topic of the article's research is the substantiation of the structure of the ACPF control system, the choice of types (transfer functions) of controllers and the calculation of their parameters. The research method chosen was the calculation of the transfer functions of the controllers of the cascaded loops control system, followed by computer simulation using the OrCAD software. The results of simulating a cascaded two loops control system of an ACPF with different types of controllers are presented and analytically compared. It is concluded that it is advisable to use a cascaded two loops control system, containing a voltage control loop and a current control loop. The best results show the simulation when using an aperiodic current controller (A-controller) and a proportional-integral voltage controller (PI-controller). The data obtained serve as the basis for further improvement of the operation of the ACPF by enhancing and optimizing the settings, structure and algorithms of the control system, which, with the selected hardware of power converter unit, will allow the ACPF to perform its functions with a high degree of reliability in an entire range of disturbing and control influences.

The Xihan River basin is located in the southern part of Gansu Province, where flood disasters occur frequently in summer and autumn, which easily pose significant risks to human life. In order to improve the accuracy of flood disaster predictions and early warnings, a flood model suitable for this region was constructed based on the HEC-HMS (Hydrologic Engineering Center's-hydrologic modeling system) model and used to determine the critical areal rainfall for flood disasters. Calibration of this model was performed using data of four flood events from May to October between 2020 and 2021, reserving data of two additional flood events for model validation. Using the calibrated HEC-HMS model, the critical areal rainfall was determined for the Pingluo and Tanjiaba hydrological stations in the basin through the model testing method. The results indicate that: (1) The stable infiltration rate of the XiHanShui River Basin was between 0.06 and 0.10 mm/h, with runoff concentration times primarily varying from 22.5 to 24.1 hours, a direct runoff storage coefficient was 0.2 hours, and a base flow index decay constant seted at 0.03 hours. (2) During the calibration and validation periods, the average peak flow relative error was 7.56%, the average runoff volume relative error was 14.76%, the average peak occurrence time difference was -0.5 hours, and the Nash efficiency coefficient was 0.769. (3) The warning areal rainfall for the Pingluo and Tanjiaba hydrological stations were 108.1mm and 128.5mm, and the guaranteed areal rainfall were 230.8mm and 184.6mm. The HEC-HMS model demonstrated high applicability and accuracy in simulating flood events in the XiHanShui River Basin, providing technical support for hydrological research and operational applications in the region.

The dynamic response of the shed-tunnel structure under rockfall impact attracts much attention in recent years. However, the research on the dynamic response of the shed-tunnel structure under rockfall impact mostly focuses on the rockfall single impact, while in practical engineering, the shed-tunnel structure often encounters the rockfall repeated impacts during its service life. Therefore, this research focuses on exploring the dynamic response characteristics of the shed-tunnel structure under the rockfall repeated impacts. First of all, based on the model test of the shed-tunnel under rockfall impact as a reference, the FEM (Finite Element Method)-SPH (Smoothed Particle Hydrodynamics) coupling numerical calculation model is established based on ANSYS/LS-DYNA finite element code. The numerical simulation of the dynamic response of the shed-tunnel structure under rockfall impact is realized, and the rationality of the model is verified. Then, with this model and the full restart technology of LS-DYNA code, the effects of four factors, e.g. rockfall mass, rockfall impact velocity, rockfall impact angle and rockfall shape, on the impact force and impact depth of the buffer layer, the maximum plastic strain and axial force of the rebar, the shed roof vertical displacement and the shed-tunnel plastic strain are studied. These results show that the cumulative deformation and damage of the shed-tunnel structure caused by the rockfall repeated impacts play an important role in the destruction of the shed-tunnel structure, and the special attention should be paid to this issue.

Due to the optical properties of the Electron Transport Layer (ETL) and Hole Transport Layer (HTL), inverted perovskite solar cells can perform better than traditional perovskite solar cells. It is essential to compare both types to understand their efficiencies. In this article, we studied inverted perovskite solar cells with NiOx/CH3NH3Pb3/ETL (ETL = MoO3, TiO2, ZnO) structures. Our results showed that the optimal thickness of NiOx is 80 nm for all structures. The optimal perovskite thickness is 600 nm for solar cells with ZnO and MoO3, and 800 nm for those with TiO2. For the ETLs, the best thicknesses are 100 nm for ZnO, 80 nm for MoO3, and 60 nm for TiO2. We found that the efficiencies of inverted perovskite solar cells with ZnO, MoO3, and TiO2 as ETLs, and with optimal layer thicknesses, are 30.16%, 18.69%, and 35.21%, respectively. These efficiencies are 1.5%, 5.7%, and 1.5% higher than those of traditional perovskite solar cells. Our study highlights the potential of optimizing layer thicknesses in inverted perovskite solar cells to achieve higher efficiencies than traditional structures.

The increasing adoption of student-centred learning environs by the institutions of higher education in business, has led to new mechanisms and methodologies such as the Simulation-Based Learning (SBL), Problem-Based Learning (PBL) and Challenge-Based Learning (CBL). Literature has shown evidence of raising interest in these methodologies towards a more experiential paradigm with regard to upcoming events from the surrounding real-world context. This paper presents a Systematic Bibliographic Literature Review (SBLR) with respect to the integration and application of these innovative and collaborative methodologies in higher education. It aimed to identify its relevant advantages, challenges, and consequences for the future of business education. Bibliographic databases were searched for documents published up to May 2024 to categorize key topics discussed in the literature on SBL, PBL and CBL. The review process identified 89 empirical and non-empirical papers on SBL, PBL and CBL, business related paperwork, which resulted from the PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) method. PRISMA is a framework with evidence-based data designed to help authors perform a systematic literature review. Data analysis revealed diverse subthemes for those methodologies uses in business higher education institutions. The research questions “What are the advantages, challenges and implications of SBL, PBL and CBL altogether, in the training of business students?” guided the study. The central output of the research is the discovery of the varying uses of SBL, PBL and CBL overall, to cope with diverse demands arising within environmental context. Future research directions are suggested.

Nowadays, unmanned vehicles are widely used in various fields. However, the safety of unmanned vehicles is directly determined by the autopilot systems, and sensor faults are a very critical factor that affects the normal operation of the autopilot systems. To efficiently and comprehensively test unmanned systems for sensor faults, this paper proposes a chip-level testing platform for unmanned vehicle autopilot systems based on FPGA hardware-in-the-loop simulation. Unlike existing testing platforms, the introduction of FPGA technology allows us to achieve nanosecond real-time simulation frequency, thus realizing chip-level simulation of sensors and black-box automated testing. Firstly, we propose a set of general platform and modeling methods, and the paper presents a detailed application of the four most common necessary sensors in autopilot systems as examples. Secondly, we propose for the first time a chip-level fault testing method for unmanned systems, and build a test platform with a quadrotor vehicle, the PX4 software platform, and the Pixhawk4 hardware platform as examples. Finally, the experimental results verify that the testing platform proposed in this paper can adapt to various autopilot systems and has high simulation test reliability.

The paper explores the features of numerical simulation to analyze the dynamic behavior of drives controlled by pulse-width modulators. Modern motor control systems widely use pulse width modulation. Effective numerical modeling of such systems has specific features because the models employed are continuous-event and have hybrid behavior due to the presence of nonlinear links with discontinuities of the first kind. Therefore, it is essential to have special integration methods with variable steps, which should be factored in when developing the model. The paper shows how these problems are solved when modeling an electric drive with a DC motor in the SimInTech software.

This study aimed to solve the problems of sealing and tearing failure of packer’s rubber cylinders during CO2 downhole injection. Using the simulation software, Comsol, a rubber cylinder model in a supercritical CO2 (SC-CO2) environment was established. The thermal analogy method was used to simulate the CO2 diffusion and rubber cylinder swelling process, thus we analyzed the deformation and stress of the rubber cylinder caused by temperature, pressure and CO2 as swelling agent. Results showed that, in the SC-CO2 environment, under the influence of CO2 diffusion and the consequent swelling, the rubber cylinder body is prone to large deformation, and the maximum shear stress is significantly increased, leading to shear failure of the rubber cylinder. The reduction of the initial seating pressure can alleviate the impact of deformation, whereas the reduction of the maximum contact pressure could cause the rubber cylinder to lose its seal. We also analyzed the change rules between various factors and the maximum contact pressure of the rubber cylinder, which provides a theoretical basis and technical support for improving the sealing performance of the packer’s rubber cylinder in the SC-CO2 environment.

: Suicide is a serious public health problem, with a global mortality rate of 1.4% of all deaths worldwide, and the leading cause of unnatural death in Spain. The use of clinical simulation has proven to be a beneficial tool in the training of nursing students. Such experiences allow them to develop cognitive and affective skills that are fundamental for the detection of warning signs and use of interventions in cases of people who want to take their own lives. Working in a mental health environment can be difficult for nursing students; therefore, the purpose of this study was to explore the perceptions of nursing students on the approach, management and intervention of suicidal crisis through clinical mental health simulation. Methods: qualitative descriptive phenomenological study through focus groups and reflective narratives in a sample of 45 students. A thematic analysis was performed using ATLAS-ti. Results: After the analysis, three themes were obtained: (a) management and handling of emotions (b) identification of suicide motives (c) intervention in suicidal crisis. Discussion: Clinical simulation in mental health allows students to exercise clinical judgment reasoning, detect warning signs for a better treatment approach, and provide tools for effective intervention and management of patient care. The results of this study indicate that nursing students face challenges in approaching mental health clinical simulation due to lack of prior exposure.

Childhood overweight/obesity (OV/OB) is a major public health problem, of greater concern when accompanied with comorbidities such as hypertension and insulin resistance leading to metabolically unhealthy obesity (MUO). Aetiologic associations between meal patterns, OV/OB risk and MUO are limited. The aim of this systematic review was to explore associations between meal patterns and the risk of childhood OV/OB and MUO. Longitudinal studies and randomised controlled trials from PUBMED and Scopus published between January 2013 - April 2024 were retrieved. Twenty-eight studies were included, all of which reported on OV/OB risk; none on MUO risk. Regular consumption of breakfast and family meals and avoiding dining while watching TV may be protective factors against childhood OV/OB, whereas meal skipping (primarily breakfast) may be a detrimental factor. Mixed effects of meal frequency on OV/OB risk were observed; no effects of frequency of lunch or of fast-food consumption and of meals served at school were found. There was insufficient evidence to support the role of other patterns (meal timing, eating in other social contexts). Meals were mainly participant-identified, leading to increased heterogeneity. Research focusing on childhood MUO and improved methodological approach (e.g. harmonised definitions) regarding the assessment of meal patterns are highly warranted.

Finding sustainable renewable energy sources for energy conversion and management is still an obscure topic. This paper presents a model-based simulation for an energy conversion system using piezoelectric energy harvester (PEH) technology. A dynamic mathematical model of a PEH device consists of a piezoelectric transducer, a controlled PWM rectifier, and a closed-loop buck boost converter is developed. A piezoelectric transducer converts mechanical vibrations from a wind force into an oscillating train of electrical charges. The sinewave peak-to-peak level relationship describes the changeable values of these charges, which depend on the severity of the wind vibration. The controlled PWM rectifier, in conjunction with a closed-loop buck-boost converter, converts this train of sinewave cycles into DC voltages. The control blocks of the closed-loop buck-boost converter use the perturbation and observation (P&O) algorithm based on maximum power point tracking (MPPT), which adapts the operational voltage of the piezoelectric source to deliver the maximum power to load and improves the PEHS output voltage stability. A simulation program is employed to perform mathematical analysis on various wind vibration scenarios, piezoelectric sources without PWM converters, and piezoelectric vibration sources connected to a closed-loop P&O converter. The crucial results of this paper demonstrate that the proposed dynamic PEHS model effectively feeds low-power electronic loads by directly adjusting the output voltage level to the set voltage, even under different vibration severity levels. As a result, the proposed PEHS dynamic model serves as a guideline for researchers in the development of self-powered sensors, which contributes to understanding sustainable energy alternatives.

The medium-voltage DC (MVDC) technology has gained increasing interests in recent years. Power electronics devices dominate those grids. Accurate simulation of such a grid, with detailed models of switching semiconductors, can quickly became very time-consuming, according to the number of connected devices to be simulated. A simulation approach based on interactions on a continuous time model can be very interesting, especially for developing a system level control model of such a modern MVDC distribution grid. Aim of this paper is to present all the steps required for obtaining a continuous time modelling of a +/- 10 kV MVDC grid case study, including Solid State Transformer (SST) and Modular Multilevel Converter (MMC) based Active Front End (AFE). Additional aim of this paper is to supply an educational content about the use of the continuous time simulation approach, thanks to a detailed description of the various devices modelled into the presented MVDC grid. The results of a certain number of simulation scenarios are eventually presented.

Muon tomography leverages cosmic muons’ exceptional penetration capabilities to reconstruct detailed tomographic images via multiple Coulomb scattering interactions, making it invaluable for detecting High-Z materials critical to homeland security. This study introduces the Slope Intercept (SI) algorithm, a novel approach for rapid and precise tomographic image reconstruction. Implemented using Geant4 simulations in a standard-sized container tomography station, SI demonstrates superior performance in speed and simplicity compared to traditional methods. While the imaging results of SI and the Point of Closest Approach (POCA) algorithm are nearly identical, the SI algorithm is simpler to implement, requires shorter CPU time, and exhibits a smaller margin of error. Its computational efficiency and simplicity make it a robust alternative to the POCA algorithm. These findings highlight SI’s suitability for applications demanding robust imaging and efficient data processing, which are crucial for advancing security measures and scientific research.

This paper explores the dynamics of political competition, resource availability, and conflict through a simulation-based approach. Utilizing agent-based models (ABMs) within an evolutionary game theoretical framework, we investigate how individual behaviors and motivations influence collective outcomes in civil conflicts. Our study builds on the theoretical model developed by Basuchoudhary et al. (2023), which integrates factors such as resource availability, state capacity, and political entrepreneurship to explain the evolution of civil conflict. By simulating boundedly rational agents, we demonstrate how changes in resource availability and state capacity can alter the nature of civil conflict, leading to different equilibrium outcomes. The findings highlight the importance of understanding individual motivations and adaptive behaviors in predicting the stability and resolution of conflicts. This research contributes to the growing body of literature on the use of agent-based models in evolutionary game theory and provides valuable insights into the complex interactions that drive civil violence.

Sources are classified into two depending upon the factor of reviving. These sources, which cannot be revived into their original shape once they are consumed, are considered as nonrenewable energy resources, i.e., (coal, fuel) Moreover, those energy resources which are revivable to the original condition even after being consumed are known as renewable energy resources, i.e., (wind, solar, hydel) Renewable energy is a cost-effective way to generate clean and green electrical energy Now a day’s majority of the countries are paying heed to energy generation from RES Pakistan is mostly relying on conventional energy resources which are mostly nonrenewable in nature coal, fuel is one of the major resources, and with the advent of time their prices are increasing on the other hand RES have great potential in the country with the deployment of RES greater reliability and an effective power system can be obtained In this thesis, a similar concept is being used and a hybrid power system is proposed which is composed of intermixing of renewable and nonrenewable sources The Source side is composed of solar, wind, fuel cells which will be used in an optimal manner to serve load The goal is to provide an economical, reliable, uninterruptable power supply. This is achieved by optimal controller (PI, PD, PID, FOPID) Optimization techniques are applied to the controllers to achieve the desired results. Advanced algorithms (Particle swarm optimization, Flower Pollination Algorithm) will be used to extract the desired output from the controller Detailed comparison in the form of tables and results will be provided, which will highlight the efficiency of the proposed system.

The aim of this work is to introduce a mathematical model representing the evolution of the temperature in a vegetation cover and the ground underneath it. Vegetation, and its interaction with soil, plays a very important role in the protection of soil surface from the action of sun and precipitations. A reduction in the vegetated mass increase the risk of desertification, soil erosion or surface runoffs which which can give rise to soil loss and sediment retention. These processes can favour climate change and global warming, which are major concerns nowadays. The mathematical model presented takes into account the main processes involved in vegetation cover and the interaction with the soil, among which, we can mention the Leaf Area Index, which is a dimensionless quantity defined as the one-sided green leaf area per unit ground surface area, or albedo and co-albedo which are clearly influenced by the vegetation. It is also considered a nonlinear heat capacity in the soil which incorporates the latent heat of fusion, when the phase change takes place. The numerical technique used to solve the mathematical model is based on a finite volume scheme with Weighted Essentially Non Oscillatory technique for spatial reconstruction and the third order Runge-Kutta Total Variation Diminishing numerical scheme is used for time integration. Some numerical examples are solved to obtain the distribution of temperature both in the vegetation cover and the soil.

In these last years, self-healing polymers have emerged as a topic of considerable interest owing to their capability to partially restore material properties and thereby extend the product's lifespan. The main purpose of this study is to investigate the nano-indentation response in terms of hardness, reduced modulus, contact depth and coefficient of friction of a self-healing resin developed for use in aeronautical and aerospace contexts. To achieve this, the bifunctional epoxy precursor underwent tailored functionalization to improve its toughness, facilitating effective compatibilization with a rubber phase dispersed within the host epoxy resin. This approach aimed to highlight the significant impact of the quantity and distribution of rubber domains within the resin on enhancing its mechanical properties. The main results are that pure resin exhibits a higher hardness (about 36.7% more) and reduced modulus (about 7% more), consequently leading to a lower contact depth and coefficient of friction (11.4% less) compared to other formulations that, conversely, are well-suited for preserving damage from mechanical stresses due to their capabilities in absorbing mechanical energy. Furthermore, finite element method (FEM) simulations of the nanoindentation process were conducted. The numerical results were meticulously compared with experimental data, demonstrating a good agreement. This validation of the FEM model underscores its efficacy in predicting the mechanical behavior of nanocomposite materials under nanoindentation. The proposed investigation aims to contribute knowledge and optimization tips about self-healing resins.

Falls are considered a significant cause of disability, pain, and premature deaths in older adults, often due to sedentary lifestyles and various risk factors. Combining immersive virtual reality (IVR) with physical exercise, or exergames, enhances motivation and personalizes training, effectively preventing falls by improving strength and balance in older people. IVR technology may increase the ecological validity of the assessments. The main goal of our study was to assess the feasibility of using a KAVE-based VR platform combining simulations of Levadas and a Cable Car to perform a balanced assessment and profiling of the older adult population for high risk-of-falls and the related user experience. A VR-based platform using a Wii balance board and a CAVE was developed to assess balance and physical fitness. Validated by the Biodex Balance System (BBS), 25 older adults participated in this study. The usability and presence were measured through the System Usability Scale and ITC-SOPI questionnaires, respectively. The IVR system showed a high presence and a good usability score of 75. Significant effects were found in the maximum excursion of the Centre of Pressure (COP) on the anterior-posterior axis during the Cable Car Simulation (CCS), correlating with BBS metrics. Multiple discriminative analysis models and the support vector machine classified fall risk with moderate to high accuracy, precision, and recall. The system accurately identified all high-risk participants using the Leave-One-Out method. This study suggests that an IVR-based platform based on simulations with high ecological validity can be used to assess physical fitness and identify individuals at a higher risk of falls.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

Dielectric barrier discharge (DBD) plasma has several applications in different fields. One of these fundamental applications is medical usages, where various methods are employed to improve the plasma treatment process. The combination of different gases is one of the important strategies to improve the performance of plasma in treatment. In this paper, the optimized plasma parameters for one-dimensional radiofrequency discharge produced at low pressures in a helium gas combination is studied. In this research, the optimal combination of H₂O and He is identified to attain the highest amount of reactive oxygen species (ROS). Considered mixture are 5,10,15 and 20 precent of H₂O for one dimensional helium gas discharge. The results show that the parameters of the output plasma are highly dependent on the composition of the input gases. It is found that the greatest concentrations of H+, He+, Hes (excited helium), and OH/ densities are observed when the H₂O percentage is 10%. Moreover, the density distributions of various species and the temperatures of electrons are numerically calculated during the electrical discharge process. These findings provide useful knowledge on how to optimize plasma parameters for biomedical applications, which may lead to improved treatment results in several therapeutic areas.

The rapid integration of Information and Communication Technology (ICT) is transforming the traditional electrical grid into a {\em Smart Grid}. Smart grids enable two-way communication and improved monitoring and control between utilities and customers. However, due to its heterogeneous nature, public exposure, and weak security at low-powered devices, the Smart Grid has vulnerabilities to various malicious threats, adversaries, and cyber attacks, which may affect cost and service availability. Additionally, when the systems' confidentiality, integrity, or availability are compromised, the resulting fallout can threaten national security and have cascading effects on human lives. Given the extreme consequences of an attack, smart-grid technology must be thoroughly tested for correct operation and security {\em before} it is deployed. As a result, vulnerability testing of smart grids, not only for correctness but for security purposes, has been the subject of numerous studies by academics, government agencies, and private companies. This paper reviews the vulnerabilities associated with the smart grid and spotlights simulation as the vulnerability testing methodology conducted in recent pertinent research works. It also presents various security aspects of the smart grid, including grid applications, system and network infrastructure and components, cyber threats and attacks, simulation, and different mitigation techniques. Finally, we analyze the gaps in the current research works, focusing on simulation. We briefly present a real-time simulation testbed that mimics customer behaviour and integrates hardware in the loop to apply attack methods, analyze vulnerabilities and risk mitigation associated with the smart grid system, and propose future work to improve the current framework.

Spectrometers have a wide range of applications ranging from optical to non-optical spectroscopy. The need for compact, portable, and user-friendly spectrometers has been the pivot of attention from small laboratories to the industrial scale. Here, the Czerny Turner configuration-based optical spectrometer simulation design is carried out using ZEMAX OpticStudio. A compact and low-cost optical spectrometer in the visible range has been developed by using diffraction grating as a dispersive element and USB-type WebCAM CCD (Charge-coupled device) as a detector instead of an expensive commercial diffraction grating and detector. Using National Instruments LabVIEW, data acquisition, processing, and displaying techniques are made possible. We have employed different virtual images in LabVIEW programs to collect the pixel-to-pixel information and wavelength-intensity information from the image captured using the WebCAM CCD. Finally, we have shown that the OpticStudio-based spectrometer and experimental measurements of the developed spectrometer are in good agreement.

Air corridors are an integral part of the advanced air mobility infrastructure. They are the virtual highways in the sky for transportation of people and cargo in the controlled airspace at an altitude of around 1000 ft. to 2000 ft. above the ground level. This paper presents fundamental insights into the design of air corridors with high operational efficiency as well as zero collisions. It begins with the definitions of air cube, skylane or track, intersection, vertiport, gate, and air corridor. Then, a multi-layered air corridor model is proposed. Traffic at intersections is analyzed in detail with examples of vehicles turning in different directions. The concept of capacity of an air corridor is introduced along with the nature of distribution of locations of vehicles in the air corridor and collision probability inside the corridor are discussed. Finally, the results of simulations of traffic flows are presented.

Differential equation models to understand interaction between plant and nutrient solution are presented. The root cells selectively emit H+ ions with active transport consuming ATPs to establish electrical gradient along the cell membrane. It establishes electrical field with Nernst potential to make positively charged ions outside the cell membrane flow into the root cell. Anion influx is also modulated by H+ ion concentration because plant root cell absorbs negatively charged particles with symport. If an anion collides with H+ cell to make net charge as neutral, at symport channel, it can flow through. In this paper, mathematical models for cation and anion absorption are introduced. Cation absorption model was induced from Ohm's law combined with Goldman's equation. Anion absorption model is similar to chemical reaction rate model. Both models have physiological terms influenced by gene expression pattern, species or phenotypes. Cation model also includes terms for ion's kinetic and electrical properties, growth of plant and interaction between the root and the surroundings. Simulation for 20 different sets of coefficients showed that the physiology-related coefficient has important role on nutrition absorption tendencies of plants.

We introduce a mission design for an interstellar expedition to nearby earth-like exoplanets, which our analysis determined to be Tau Ceti and Gliese 667C, at the time of analysis in 2013. We review the research problems in propulsion and AGI that must be addressed to launch an AI guided interstellar probe within 100 years. We propose a new semi-autonomous agent approach for intelligent control of the spacecraft. We introduce the concept of a semi-autonomous agent as having built-in safety guarantees that constrain operation. An autonomous agent case study is presented formulating the objective, constraints, AGI implementation of the agent based on Solomono's Alpha architecture, and adding specicity. We discuss the training required to reach human-level and trans-sapient levels of intelligence which corresponds to an entire crew of AI experts specialized in elds such as astrophysics, astromechanics, astrobiology, quantum physics, computer science, molecular biology, and so forth. We project the feasibility of the human-level AI technology based on empirical ndings in neuroscience, and nd that it should be feasible by 2030. We analyze Solomono's innity point hypothesis in light of Koomey's law about energy eciency of computing and nd that the trends in 2013 indicated an early singularity by 2035, which implies that we might encounter physical bottlenecks which will decelerate computing technology improvements signicantly. We recommend thus year 2040 for launching the probe by which date other required technologies will have been developed. We discuss the scenario of a virtual crew made of brain simulations, which is a bio-information based AI approach. We detail the subsystems of command and control, communication, scientic instrumentation, power, propulsion, navigation, and shielding. We propose a variation of ICAN-II/AIMStar propulsion which uses a positron source instead of anti-protons to initiate micro-fusion reactions. We combine the positron initiated fusion pulse propulsion scheme with a miniaturized version of the Daedelus fusion thruster obtaining high performance. We derive two mission proles one for fusion pulse propulsion, and the yet hypothetical Q-Thruster. Fusion thruster requires 132.2 years for Tau Ceti, and 233.2 years for Gliese 667C, while Q-Thruster takes only 42.3 years for Tau Ceti, and 62.5 years for Gliese 667C. We also discuss extended roles for intelligent interstellar probes such as self-reproduction via nanotechnology, refueling, construction, robotic bodies, and transmission of brain simulations.

This paper shows that by applying the Nyquist-Shannon sampling theorem, the spatial and temporal resolution of a simulation can be no more than half the resolution of the simulating reality. This has significant implications for not only the values of the observables in the simulation but also its physical laws. This progressive halving of nested simulations coupled with the minimum resolution compatible with the production of a simulation also sets a limit to the nestedness of a lineage of simulations (it is by no means infinite). The limit of nestedness is then used to calculate the probability that we are living in a simulation assuming a single base reality. This will be shown to be significantly lower than popular expectation. A Kardashev-like scale, with three variants, is also developed to gauge the technological advancement of a civilization in relation to the extent to which it can extract information from space and time.

In this work, the deoxygenation of organic liquid products (OLP) obtained by thermal catalytic cracking of palm oil at 450 °C, 1.0 atmosphere, with 10% (wt.) Na₂CO₃ as catalyst, in multistage countercurrent absorber columns using supercritical carbon dioxide (SC-CO₂) as solvent, with Aspen-HYSYS process simulator was systematically investigated. In a previous study, the thermodynamic data basis and EOS modeling necessary to simulate the deoxygenation of OLP has been presented [Molecules 2021, 26, 4382. https://doi.org/10.3390/molecules26144382]. This work address a new flowsheet, consisting of 0₃ absorber columns, 10 expansions valves, 10 flash drums, 08 heat exchanges, 01 pressure pump, and 0₂ make-up of CO₂, aiming to improve the deacidification of OLP. The simulation was performed at 333 K, 140 bar, and (S/F) = 17; 350 K, 140 bar, and (S/F) = 38; 333 K, 140 bar, and (S/F) = 25. The simulation shows that 81.49% of OLP could be recovered and the concentrations of hydrocarbons in the extracts of absorber-01 and absorber-02 were 96.95 and 92.78% (wt.) in solvent-free basis, while the bottom stream of absorber-03 was enriched in oxygenates compounds with concentrations up to 32.66% (wt.) in solvent-free basis, showing that organic liquid products (OLP) was deacidified and SC-CO₂ was able to deacidify OLP and to obtain fractions with lower olefins content. The best deacidifying conditions was obtained at 333 K, 140 bar, and (S/F) = 17.

The water exit problem, which is ubiquitous in ocean engineering, is one of the significant research topics in the interaction between navigators and water. The study of the water exit problem can help to improve the structure design for marine ships and underwater weapons for better strength and movement status. However, the water exit problem involves complex processes such as gas-liquid-solid three-phase coupling, cavitation, water separation, liquid surface deformation and fragmentation, making it challenging to study. According to the works carried out by many researchers towards this issue, we summarize the recent developments from three aspects, i.e. theoretical research, numerical simulation and experimental results. In theoretical research, the improved von Kaman model and linearized water exit model are introduced. Several classical experimental devices, data acquisition means and cavitation are introduced in experimental development. Three methods, namely, BEM(boundary element method), FVM(finite volume method) and LES(large eddy simulation) are concluded for numerical simulation. The limitations and shortcomings of these three aspects are then analyzed. Finally, an outlook on the future research improvements and developments of the water exit problem is provided.

3D-printed models with high anatomic fidelity are an increasingly viable tool in simulation-based medical education. One advantage of 3D models is they provide enhanced tactile and spatial understanding of complex anatomy to develop technical skills used in minimally invasive procedures. We propose that 3D anatomical models can improve the development of Interventional Radiology vascular access skills – first described in the 1950s as the Seldinger Technique – for pre-clerkship medical students. Early adoption of 3D-printed technology in pre-clinical medical education can lead to improved student engagement and satisfaction when learning procedural techniques. This study involved creating a 3D model of the upper extremity vasculature from an anonymized CT angiogram, using it as a medical education tool for 31 pre-clinical medical students practicing the Seldinger Technique on a prefabricated venipuncture arm, and assessing student satisfaction with this form of learning. Overall, attendees responded positively to the incorporation of the 3D model in medical education to improve their anatomic understanding and application to the Seldinger Technique. These results indicate that the use of 3D models in simulation-based medical education can provide benefits to acquiring technical skills and the potential to decrease training costs without harming a patient.

In this study, Acısu Basin, which is upper side of one of the most important basins (Gediz) in Türkiye, was modelled using three types of hydrological models and three different calibration algorithms. Lumped (GR4J), semi-distributed (SWAT+), and fully distributed (mHM) hydrological models were built and integrated with Parameter Estimation Tool (PEST) which is a model independent calibration tool including various algorithms. Levenberg Marquardt (L-M), Shuffled Complex Evolution (SCE), and Covariance Matrix Adoption Evolution Strategy (CMA-ES) were selected as calibration algorithms. Calibration period was 1991-2000, and validation results were obtained for 2002-2005. The effect of model structure and calibration algorithm selection on discharge simulation was evaluated via comparison of 9 different model-algorithm combinations. Results have shown that mHM and CMA-ES combination showed the best discharge simulation performance according to NSE values (calibration: 0.67, validation: 0.60). Although statistically the model results were classified as acceptable, the pattern comparison of discharge value shows that all of the models miss the peak values in significant amounts. This problem may be related to the interventions made in 2000-2001 years interval and possible to overcome by changing the calibration and validation periods, increasing the number of iterations or using the naturalized gauge data.

This paper is focused on understanding multiscale modelling to obtain a bridge among different time and length scales of simulation techniques. These techniques are vital as it holds the potential to understand and predict the capabilities of polymer nanocomposites (PNCs). However, an appropriate approach in controlling the interfacial interaction between nanoparticle and polymer in nanocomposites structure is still needed to develop. In this review, an initial brief introduction to various trending simulation techniques has been discussed at all three levels of scale (nm, μm, mm). Later, descriptive study on fundamental issues such as thermodynamics, kinetics, mechanical properties, and morphology has been studied deeply. The multiscale modeling bridges the gaps of simulation between the different scales of models from molecular to mesoscale levels working over the broad range of length and timescale. Through the sequential, adaptive, and concurrent approaches, we can develop a system that may comprehend multiscale mode modeling adaptive resolution approach has recently added approach the molecule of the subject can shift their position freely in the domain and through this approach and studied the Brownian motion. Co-The co-current coach is also termed as handshaking path and it is linked aiming at different scale models. Covering the rigid techniques smoothly and linking them at different scales helps in normalizing the statistical behaviour.

In Differentiated Services (DiffServ) architecture, Priority Service System (PSS) plays a vital responsibility to provide Quality-of-Service (QoS) for the applications based on networks. Priority queuing systems has always been a subject of interest for analytical modelling and evaluating the performance. However, previous works have mainly focused on performing priority queuing under range dependent traffics, namely Short Range Dependent (SRD) or Long Range Dependent (LRD). Recent studies revealed that realistic traffic demonstrates a heterogeneous nature for the modern networks that provide multiple services. In this paper, the results of analytical and simulation models of dynamic priority service systems is reviewed to study the heterogeneous traffic impact on designing and performance of the systems based on networks. In this paper, the results of analytical and simulation models of dynamic priority service systems is reviewed to investigate the impact of heterogeneous traffic on the design and performance of network-based systems. Here, the time of presence of requests in limited and unlimited buffer system is restricted. If the restriction is violated, the requests will be lost. The results of experiments conducted on both models are compared and it is identified that they differ in the allowable limit (2-9) %.

Is it possible to develop a meaningful measure for the complexity of a simulation model? Algorithmic information theory provides concepts that have been applied in other areas of research for the practical measurement of object complexity. This article offers an overview of complexity from a variety of perspectives and provides a body of knowledge with respect to the complexity of simulation models. Key terms of model detail, resolution, and scope are defined. An important concept from algorithmic information theory, Kolmogorov complexity, and an application of this concept, normalized compression distance, are used to indicate the possibility of measuring changes in model detail. Additional research in this area can advance the modeling and simulation body of knowledge toward the practical application of measuring simulation model complexity. Examples show that KC and NCD measurements of simulation models can detect changes in scope and detail.

Summary: Studying biological systems generally relies on computational modeling and simulation, e.g., for model-driven discovery and hypothesis testing. Progress in standardization efforts led to the development of interrelated file formats to exchange and reuse models in systems biology, such as SBML, the Simulation Experiment Description Markup Language (SED-ML), or the Open Modeling EXchange format (OMEX). Conducting simulation experiments based on these formats requires efficient and reusable implementations to make them accessible to the broader scientific community and to ensure the reproducibility of the results. The Systems Biology Simulation Core Library (SBSCL) provides interpreters and solvers for these standards as a versatile open-source API in Java™. The library simulates even complex bio-models and supports deterministic Ordinary Differential Equations (ODEs); Stochastic Differential Equations (SDEs); constraint-based analyses; recent SBML and SED-ML versions; exchange of results, and visualization of in silico experiments; open modeling exchange formats (COMBINE archives); hierarchically structured models; and compatibility with standard testing systems, including the Systems Biology Test Suite and published models from the BioModels and BiGG databases. Availability and implementation: SBSCL is freely available at https://draeger-lab.github.io/SBSCL/.

This article is devoted to Feller's diffusion equation which arises naturally in probabilities and physics (e.g. wave turbulence theory). If discretized naively, this equation may represent serious numerical difficulties since the diffusion coefficient is practically unbounded and most of its solutions are weakly divergent at the origin. In order to overcome these difficulties we reformulate this equation using some ideas from the Lagrangian fluid mechanics. This allows us to obtain a numerical scheme with a rather generous stability condition. Finally, the algorithm admits an elegant implementation and the corresponding Matlab code is provided with this article under an open source license.

Multi-stage hydraulic fracturing with horizontal well technology has been widely used in shale oil reservoir. After hydraulic fracturing, hydraulic fractures and opened beddings are intertwined, which result in a complex fracture network. As well as the migration of multi-phase fluids during fracturing and soaking processes, which lead to complex flowback performance, and brings dif-ficulty to productivity evaluation and flowback strategies optimization. In this paper, taking the Daqing Gulong shale reservoir as an example, a numerical model for flowback period, which considered oil-water-gas three-phase flow and orthogonal fracture network has been established. The characteristics and influencing factors of flowback performance have been deeply studied, and the flowback modes of shale oil are reasonably optimized. Factors such as PTPG (pseu-do-threshold pressure gradient), opened bedding stress sensitivity, opened bedding permeability and matrix permeability have obvious effects on the flowback performance, resulting in signifi-cant variations in production peaks, high yield periods, and decline rates. In addition, three flowback modes are distinguished based on the rate at which the BHP (bottom hole pressure) drops. These correspond to three types of choke modes. Based on the result of numerical model, three flowback modes are optimized and the impacts of different flowback modes on shale oil flowback are clarified. This study is particularly important for understanding the performance of shale oil flowback and guiding the efficient exploitation of shale oil.

This literature review investigates the importance of simulation and measurement techniques in the development of transmission lines and antennas, which are crucial to the reliability and efficiency of communication system. It emphasizes the necessity of exact measurement and computational approaches for simulating complicated electromagnetic process, which help to optimize designs before physical prototypes are built. The review examines a variety of research articles that offer innovative solutions to improving accuracy in antenna design, scalability and cost challenges in antenna measurements, and crosstalk measurement methods. It also explores how these methodologies affect antenna design parameters such as gain, bandwidth, and radiation patterns, emphasizing the importance of correct modeling to ensure the performance of transmission lines and antennas in modern communication system. The review serves as a valuable reference for guiding future research and technological advancements in these fields.

In the end, this paper analyzed the economy from the investment in plant construction, raw material collection, product production and product sales. The resulting products include pyrolytic carbon, pyrolytic oil, pyrolysis gas. The results showed that when the treatment scale was 1 ton h−1, the pyrolysis plants with three loading modes will always be in a state of loss during the 20-year running time. When the processing scale was 9 ton h−1, the pyrolysis plant can be profitable in the first year. In the sensitivity analysis, the influence of three pyrolysis products on the total return on investment was explored. The results showed that the price change of pyrolysis oil has the greatest influence on the total return on investment (Total ROI) under the three loading methods, The price change of pyrolysis gas has minimal impact on the Total ROI. This study provides basic data and basis for the commercialization of coal-biomass co-pyrolysis technology and investment in plant construction.