In this study, literature on pore structure and chloride ion diffusivity was collected to investigate the correlation of pore structure indicators with diffusivity. Good correlation between total porosity and chloride ion diffusivity was found when the samples did not contain admixture materials and diffusion test was conducted without acceleration. Pore diameter indicators did not correlate with diffusivity. The diffusivity of cement paste was reduced by admixture materials compared to that without admixture materials even if the total porosity is the same. On the other hand, the diffusivity of concrete was not reduced by admixture materials.

Ion current rectification (ICR) is the ratio of ion current by forward bias to by backward bias and is a critical indicator of diode performance. In previous studies, many attempts have been continued to improve the performance of this ICR, but there is the intrinsic problem for geometric changes that induce ionic rectification due to their fabrication problem. Additionally, the high ICR could be achieved in the narrow salt concentration range only. Here, we propose a multi-layered bipolar ionic diode based on an asymmetric nanochannel network membrane (NCNM), which is realized by soft lithography and self-assembly of homogenous-sized nanoparticles. Owing to the freely changeable geometry based on soft lithography, the ICR performance can be explored according to the variation of microchannel shape. Interestingly, very stable ICR performance can be achieved using the multi-layered 3D configuration for the bipolar diode in a broad range of salt concentrations (0.1mM ~ 100 mM). This demonstrates the promising potential of multi-layered NCNM for applications in highly concentrated electrolytes, such as biosensors, desalination, or energy harvesting.

Immersion in salt-lake solution was adopted to periodically test the concrete chloride-ion diffusion coefficient. The regression analysis was also completed. Also investigated was the time-dependent law of concrete chloride-ion diffusion coefficient with time. The influence of chloride-ion concentration in solution, water-to-cement ratio, and corrosion time on the largeness and accumulation rate of the concrete chloride-ion diffusion coefficient was also analyzed. Test results show that the concrete chloride-ion diffusion coefficient gradually decreased with increasing time and increased with increasing chloride-ion concentration in a salt lake . Taking into account the influence of factors such as water–binder ratio, chloride-ion concentration, and time-varying characteristics, a multi-factor calculation model for the concrete chloride-ion diffusion coefficient was established. Combining the prediction results and the measured data reported in this paper, the effectiveness and applicability of the established concrete chloride-ion diffusion coefficient calculation model were compared and verified, and the durability design and service life of a concrete structure under cool chlorine were compared. The results of analysis provide important boundary conditions.

The research presented in this article is based on a strategic approach to a rural area in the mountainous region of Romania and is underwritten by specialists in the economy of mountainous regions in order to elaborate relevant solutions to complex problems relating to sustainable development. In essence, the research underlines and promotes the particularities of performing research for the identification and valuation of endogenous resources, that is, creating relevant strategic options for the durable development of the mountainous region, centered on the renewal of economic activities related to the existent endogenous resources, by using methods, work techniques, and instruments of strategic analysis. These factors are subordinate to the process of harmonization to the requirements of community development and environmental protection according to the new strategy for the development of the European Union 2020 (European Green Pact). This pact also emphasizes the necessity of involving the different factor categories of local accountability, promotion, activation, and the development of specific economic activities of different local contexts of sustainability. The research methodology used involves a case study whose complexity necessitated the use of quality and quantity research methods in order to underline specific elements of the rural area in the Romanian mountainous region. Specifically, we used a strategic diagnosis of the Romanian mountainous region using the PESTEL and SWOT models. In order to have relevant strategic options available, the continuity of research was achieved through the use of SOR analysis, creating a problem tree and an objectives tree.

For concrete structures exposed to offshore areas, chloride ion erosion is one of the main factors affecting the durability. It is crucial to evaluate chloride ion permeability resistance of concrete structures. In this article, a finite element simulation of the chloride ion diffusion process in concrete is conducted. A mass diffusion finite element model based on random aggregate approach is established to investigate the influence of aggregate, interface transition zone, and micro-cracks on chloride ion diffusion coefficients in concrete. The results show that the mass diffusion finite element analysis based on the exponential function model and power function model can effectively simulate the chloride ion diffusion process in concrete. In addition, the data reveal that coarse aggregate is the most important factor affecting chloride ion diffusivity in concrete. However, the interface transition zone significantly accelerates chloride ion diffusion in concrete. Moreover, this acceleration effect exceeds the barrier effect of aggregate.

In cold-climate regions, road salt is used as a de-icer for winter road maintenance. The applied road salt melts ice and snow on roads, being washed off through storm sewer systems into nearby urban streams, harming the freshwater ecosystem. Addressing the gap in the knowledge regarding the use of deep learning approaches for urban stream water quality forecasting, the present work discusses our implementation of a “Graph Neural Network” - “Sample and Aggregate” (GNN-SAGE) model for forecasting chloride concentrations in the Credit River in Ontario, Canada. The proposed GNN-SAGE is compared to other models, including a Deep Neural Network based transformer (DNN-Transformer) and a benchmarking persistence model for 6 hours forecasting horizon. Ac-cording to the results, the GNN-SAGE model surpasses other models in providing accurate predic-tions of chloride concentrations within the assessed prediction window. Also, a SHAP analysis provides insight into the variables that influence the model’s forecasting, showing the impact of the spatiotemporal neighbouring data from the network and the seasonality variables on the model’s result. The GNN-SAGE model shows potential for use in real-time forecasting of water quality in urban streams, aiding in the development of regulatory policies to protect the vulnerable freshwater ecosystems in urban areas.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

A new trend in cow's milk has emerged in the market called type A1 and A2 milk. These products have piqued the interest of both consumers and researchers. Recent studies suggest that A2 milk may have potential health benefits, which is why researchers are investigating this product further. It is interesting to note that the A1 and A2 milk types have area-specific characteristics compared to breed-specific characteristics. Extensive research has focused on milk derivatives obtained from cow’s milk, primarily through in vitro and animal studies. However, few clinical studies have been conducted in humans, and the results have been unsatisfactory. New molecular techniques for identifying A1 and A2 milk may help researchers to develop new studies that can clarify certain controversies surrounding A1 milk. It is essential to exercise extreme caution when interpreting the updated literature. It has the potential to spread panic worldwide and have negative economic implications. Therefore, this study aims to investigate the new aspects of A1 and A2 milk in different research areas and clarify some aspects regarding these two types of milk.

In a recent article, Smoom et al. identified an important amino acid variation in the helicase RTEL1 of the Algerian mouse (Mus spretus). Since the latter has telomeres five times shorter than the laboratory mouse (belonging to the Mus musculus species), they introduced this variation in laboratory mice, in order to obtain an engineered strain with human-length telomeres. Succeeding in doing this, they established the “Telomouse” strain. Here I demonstrate that, in reality, Mus spretus does not show this variation: the key amino acid is conserved in all rodent species, which all have human-length telomeres (including wild Mus musculus species). This finding in no way compromises the value of the research of Smoom et al. and the utility of the Telomouse strain. Rather, it raises the question of how the telomere length of Mus musculus (as a species) should be considered and the important consequences it has on studies on inter-species comparison.

As Li-ion batteries use is spreading, incidents in large energy storage systems (stationary storage containers, …) or in large-scale cell and battery storages (warehouse, recyclers, …), often leading to fire, are occurring on regular basis. Water remains one of the most efficient fire extinguishing agents for tackling those battery incidents and large quantities are usually necessary. Since bat-teries contains various potentially harmful components (metals and their oxides or salts, sol-vents…) and that thermal runway induced battery incidents are accompanied with complex and potentially multistage fume emissions (containing both gas and particles) the potential impact of fire run-off water on the environment should be considered and assessed carefully. The tests presented in this paper focus on the analysis of the composition of run-off waters used to spray NMC Li-ion modules under thermal runaway. It highlights that waters used for fire-fighting are susceptible to contain many metals, including Ni, Mn, Co, Li and Al mixed with other carbonaceous species (soot, tarballs) and sometimes undecomposed solvents used in the elec-trolyte. Extra-polation of pollutant concentrations compared with PNEC values showed that, for large scale incidents, run-off water could be potentially hazardous to the environment.

The mechanism underlying microbiologically induced carbonate precipitation have not been thoroughly characterized, although numerous scholars and experts have specifically investigated questions regarding minerals induced by bacteria. The study of the precipitation of carbonate minerals induced by halophilic bacteria has aroused wide concern. The present study aimed to investigate the characterization and process of biomineralization in high salt systems by a halophilic bacterium, Chromohalobacter israelensis strain LD532 (GenBank: KX766026), which was isolated from the Yinjiashan Saltern in China. Carbonate minerals induced by LD532 were investigated in several sets of comparative experiments that employed magnesium sulfate and magnesium chloride as Mg resources. Magnesium calcite and aragonite were induced by LD532 bacteria, whereas these minerals did not appear in the control group. The mineral phases, micromorphologies, and crystal structures were analysed using X-ray powder diffraction, scanning electron microscopy, and energy dispersive X-ray detection. The carbonic anhydrase and urease secreted by strain LD532 through metabolism increased the pH value of the liquid medium and promoted the process of carbonate precipitation. Further study using high resolution transmission electron microscopy, energy dispersive X-ray detection and analysis of ultrathin slices showed that the nucleation sites of carbonate minerals were located on extracellular polymeric substances and the membranes of intracellular vesicles of LD532 bacteria, which provided favourable conditions for the growth of carbonate mineral crystals. The morphologies and compositions of minerals formed in solutions of MgSO₄ and MgCl₂ display significant differences, indicating that different sources of Mg²⁺ may also affect the physiological and biochemical activities of microorganisms and thus mineral deposition. This study will be of some interest for the interpretation of carbonate biomineralization in natural salt environments and has some value as a reference in understanding sedimentary carbonates in ancient marine environments, such as tidal flats.

Innovative tissue engineering biomimetic hydrogels based on hydrophilic polymers have been investigated for their physical and mechanical properties. 5% to 25% by volume loading PHEMA-nanosilica glassy hybrid samples were equilibrated at 37°C in aqueous physiological isotonic and hypotonic saline solutions (0.15 and 0.05 M NaCl) simulating two limiting possible compositions of physiological extracellular fluids. The glassy and hydrated hybrid materials were characterized both for dynamo-mechanical properties and equilibrium absorptions in the two physiological-like aqueous solutions. Mechanical and the morphological modifications occurring in the samples have been described. The 5% volume nanosilica loading hybrid nanocomposite composition showed mechanical characteristics in the dry and hydrated states that were comparable to those of cortical bone and articular cartilage, respectively, and then chosen for further sorption kinetics characterization. Sorption and swelling kinetics were monitored up to equilibrium. Changes in water activities and osmotic pressures in the water-hybrid systems equilibrated at the two limiting solute molarities of the physiological solutions have been related to the observed anomalous sorption modes using the Flory-Huggins interaction parameter approach. The bulk modulus of the dry and glassy PHEMA-5% nanosilica hybrid at 37°C has been observed to be comparable with the values of the osmotic pressures generated from the sorption of isotonic and hypotonic solutions. The anomalous sorption modes and swelling rates are coherent with the difference between osmotic swelling pressures and hybrid glassy nano-composite bulk modulus: the lower the differences the higher the swelling rate and equilibrium solution uptakes. Bone tissue engineering benefits of use of tuneable biomimetic scaffold biomaterials that can be “designed” to act as biocompatible and biomechanically active hybrid interfaces are discussed.

The steady-state dissolution rates of basaltic glass and labradorite have been measured in the presence of 10 to 700 x 10-3 mol kgw-1 aqueous NaCl, KCl, CaCl2, and MgCl2 at 25 oC. All rates were measured in mixed flow reactors, and at pH~3.6 by the addition of HCl to the reactive fluids. Steady-state basaltic glass dissolution rates based on Si release increased by ~0.3 log units in the presence of 1 x 10-2 mol kgw-1 of CaCl2 or MgCl2, compared to their rates in 10 x 10-3 mol kgw-1 of NaCl, and KCl. In contrast, the steady-state dissolution rates of labradorite decreased by ~0.4 log units in the presence of 10 x 10-3mol kgw-1 of CaCl2 or MgCl2, compared to their rates in 10 x 10-3 mol kgw-1 of NaCl, and KCl. These contrasting behaviours likely reflect the varying effects of these cations on the stability of rate controlling Si-rich activated complexes on the surface of the solids. On average, the Si release rates of these solids are similar to each other and increase slightly with increasing ionic strength. As the pH of water charged with 10 to 30 bars CO2 is ~3.6, the results of this study indicate that both basaltic glass and labradorite dissolution will likely be effective at increasing pH and adding Ca to the aqueous phase in saline fluids. This observation supports potential efforts to store carbon through its mineralization in saline aquifers containing Ca-bearing feldspar and in submarine basalts.

The paper presents a method to assess the effect of electrolyte additives on the energy capacity of Pb-acid batteries. The method applies to any chemically unreactive additive, including suspensions and gels. The approach is thermodynamically based and it leads to the definition of a region of admissible concentrations –the battery’s admissible range– where the battery can undergo an indefinite number of charge/discharge cycles without suffering permanent damage. An experimental procedure to determine this range is presented. The obtained results provide a way to assess the potential of electrolyte additives to improve the energy capacity of Pb-acid batteries. The same results also provide a means to determine the additive concentration that produces the maximum energy capacity increase of the battery. The paper closes with an example of application of the proposed approach to a practical case.

Lactoperoxidase (LP), which is a high-value minor whey protein, has recently drawn extensive attention from research scientists and industry due to its multi-function and potential therapeutic applications. In this study, the separation and optimization of two similar-sized proteins, LP and lactoferrin (LF) were investigated using strong cation exchange column chromatography. Optimization was started with central composite design based experiments to characterize the importance of different decision variables. The three variables used in the optimization were flow rate, length of gradient and final salt concentration in the linear elution gradient step. The obtained empiric functional model represented the effect of the significant factors on the yield as the objective function. Afterwards, the calibrated mechanistic model was employed to predict accurate optimal set of variables. The optimal operating points were found and the results were compared with validation experiments. Predictions respecting yield confirmed a very good agreement with experimental results while keeping purity, a product quality characteristic, equal or above to a predefined value.

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

For both conventional and renewable energy conversion processes, computational fluid dynamics (CFD) has been used to address more energy-related challenges in recent decades. Using CFD to investigate vertical-axis wind turbines has become more common in recent years. The main goals of this application have been to more accurately predict the turbine's performance and to comprehend the complicated nature of the complex turbulent flow. The Vertical Axis Wind Turbine (VAWT) simulation for energy-generating applications has several intricate components. One of them is being aware of the chaotic flow that occurs during the first stages of the starting process, which influences overall effectiveness. In this article, the performance of the wind turbine was increased by using a passive flow control approach. The numerical research was carried out using Large Eddy Simulation for four alternative tip speed ratios in both cases, the classic and the optimized, equipped with a vortex trap on the exterior of the blades. The power and torque coefficient variations, as well as the velocity magnitude contours, show that the starting process may begin with a significant improvement in efficiency when flow control is used.

We give a simple proof of the Chen inequality for the Chen invariant $\underbrace{\delta (2,...,2)}_{k\mbox{ terms}}$ of submanifolds in Riemannian space forms.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

In this article, we give a brief review of the origin of the neutrino mass in some interesting non-linear supersymmetric models with R-symmetry. These models are able to address and solve the most important problems of the particle physics and provide mechanisms for neutrino mass generation and their mixing parameters in agreement with the current experimental data. Their prediction could be experimentally tested in the near future by collider experiments.

The paper deals with the problems of direct kinematics related to a 2T6R robot, the direct kinematics of the plane mechanism of the robot. The direct kinematics of this proposed new robot help to study the movement, including the dynamic one, to determine the forces in the mechanism and to model the possible trajectories of the final effector point, thus determining the robot's working space and some of its multiple possible uses. Two totally different methods were used to verify the calculation relations, the results obtained by both methods being practically identical. The first method used is an original trigonometric method, and the second is an original geometrically analytical method.

The increasing regulatory pressure to monitor and reduce GHG emissions and air pollutants requires cost-effective methods for their surveillance. The most common technique used for scientific investigations on gas concentration monitoring in barns are accurate but expensive and with a complex maintenance. This research study analysed the potential use of a low-cost portable measurement devices for the measurement of ammonia (NH3) and carbon dioxide (CO2) concentrations in an open dairy barn. A comparison between gas concentrations acquired at different heights from the floor by using portable devices and those acquired by a photoacoustic infrared multigas spectroscope (i.e., reference measurement) in the same sampling locations was carried out to determine the precision of the low-cost portable devices. The performance of low-cost portable devices was statistically analysed by the application of the one-way analysis of variance, correlation analysis and regression analysis. The results showed a significant difference between gas concentration values at various heights from the floor for both NH3 and CO2. The correlations between concentrations acquired by the low-cost portable device and the INNOVA were statistically significant (r=0.83; P<0.001) for gas concentrations monitored at 0.4 m from the floor. Compared with the reference measurement device, the low-cost devices were effective in the monitoring of NH3 concentrations at 0.40 m from the floor though it underestimated them in the barn at increasing of the height from the floor, whereas the device was not adequate for CO2 concentrations. In detail, the relative measurement error of the low-cost devices compared to INNOVA was reduced close to the floor during NH3 concentration measurements. Within these limitations, this device could be useful for monitoring NH3 concentration in the barn and to assess variation in NH3 concentrations mainly related to the animal occupied zone. Further efforts are needed in this field of research to identify low-cost device that could simplify emission estimation from open dairy barns.

Nanoporous membranes promise energy-efficient water desalination. Hexagonal boron nitride (h-BN), like graphene, exhibits outstanding physical and chemical properties, making it a promising candidate for water treatment. We employed Car–Parrinello molecular dynamics simulations to establish accurate modeling of Na+ and Cl- permeation through hydrogen passivated nanopores in graphene and h-BN membranes. In these complex systems the classical potentials cannot properly account for the physics at play. We demonstrate that ion separation works well for the h-BN by imposing a barrier of 0.13 eV and 0.24 eV for Na+ and Cl- permeation respectively, compared to the graphene where the Cl- ion faces a negative barrier of 0.68 eV and is prone toward blockade and Na+ permeation is associated with a slightly negative barrier of 0.03 eV. From the change in the solvation shell, we get the following trend: Na/h-BN > Na/G > Cl/G > Cl/h-BN. We argue that the trend in the permeation barrier changes to Cl-h-BN > Na-h-BN > Na-G > Cl-G due to a combination of several interactions, including the distortion of the water network induced by the ions, the ion-water interaction, and the ion-nanopore interaction. Overall, the desalination performance of h-BN surpasses that of their graphene counterparts.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

A good optical quality crystal of 2-aminopyridine (2AP) metal complex crystals was grown by slow evaporation technique at room temperature. The transparent and defect less bulk size of 2-aminopyridine potassium dihydrogen orthophosphate metal complex crystals have been grown by solution growth method. The molecular structure and morphology of grown crystals was drawn and planes are indexed using WINXMORPH software. A optical absorption spectrum, the UV cut-off wavelength, Band gap (Eg), Reflectance (R), Refractive Index (n), Extinction coefficient (K) and Electrical susceptibility (χc) are calculated for 2AP metal complex crystals.

Based on the need for real-time sag monitoring of Overhead Power Lines (OPL) for electricity transmission, this article presents the implementation of a hardware and software system for online monitoring of OPL cables and cable sag determination. The mathematical model based on differential equations and the methods of algorithmic calculation of OPL cable sag are presented. Considering that, based on the mathematical model presented, the calculation of OPL cable sag can be done in different ways depending on the sensors used, and the presented application uses a variety of sensors. Therefore, a direct calculation is made using one of the different methods. Subsequently, the verification relations are highlighted directly and, respectively, the calculation by the alternative method, which uses another group of sensors, to generate both a verification of the calculation and the functionality of the sensors, thus obtaining a defect observer of the sensors. The hardware architecture of the OPL cable online monitoring application is presented, together with the main characteristics of the sensors and communication equipment used. The configurations required to transmit data using the ModBUS and ZigBee protocols are also presented. The main software modules of the OPL cable condition monitoring application are described, which ensure the monitoring of the main parameters of the power line and the visualisation of the results both on the electricity provider's intranet using a web server and MySQL database, and on the Internet using an Internet of Things (IoT) server. This categorisation of the data visualisation mode is done in such a way as to ensure a high level of cyber security. Starting from the mathematical model of the OPL cable sag calculation, it goes through the stages of creating such a monitoring system, from the numerical simulations carried out using Matlab to the real-time implementation of this monitoring application. The main modules of the application software are: the software module for reading quantities from the sensor network through a ModBUS Input/Output (I/O) server, the software module for real-time calculation of the OPL cable sag, the software module for read/write operations based on MySQL type data, the software module for transferring data to the user's intranet through a web server, and the software module for viewing data by authorised users based on user and password through an IoT server. The development software environments used are Matlab and Laboratory Virtual Instrument Engineering Workbench (LabVIEW).

The corrosion inhibition behavior of cetyl pyridinium chloride (CPC) on mild steel (MS) in 0.5 M H₂SO₄ solution was examined using the weight loss method and potentiodynamic polarization method. The experimented MS surface was characterized by Fourier Transform Infrared Spectroscopy (FTIR), Field Emission Scanning Electron Microscopy (FESEM), and Atomic Force Microscopy (AFM). Corrosion rate and corrosion efficiency was calsulated via weight loss and potentiodynamic polarization methods where the corrosion rate in 0.5 M H₂SO₄ , 0.000192 M, and 0.0077 M of CPC solution was 12.09×10^-3, 8.23×10^-3, 6.63×10^-5 (mm/Year), respectively and the inhibition efficiency of 94.42% and 98.54%. FESEM studies demonstrated the corrosion attack on MS surface. Also, the EDX showed the presence of nitrogen of CPC. Thus, CPC acts as an important corrosion inhibitor.

Even though the current classic aerospace propulsion methods are greatly improved, some of the most modern methods have already been introduced, among which the propulsion with electric motors. Energy can be obtained from hydrogen burners, honeycomb burners to protect the burning of hydrogen that burns 10 times faster than conventional oil fuels or alcohols. Hydrogen storage is also done in honeycomb cell reservoirs. Getting solar photovoltaic power even during flight is not yet profitable or efficient, but it can be proposed in the future for lighter and/or spacecraft. A great desire is to dismantle water in hydrogen and oxygen directly on the aircraft, so the stored fuel is actually water and the one actually used is the hydrogen removed from the water. In this case, there is no need for hydrogen storage. And other modern methods of propulsion and energy acquisition are briefly presented in the paper.

Solvent-free, single-ion conducting electrolytes are sought after for use in electrochemical energy storage devices. Here, we investigate the ionic conductivity and how this property is influenced by segmental mobility and conducting ion number in crosslinked single-ion conducting polyether-based electrolytes with varying tethered anion and counter-cation types. Crosslinked electrolytes are prepared by the polymerization of poly(ethylene glycol) diacrylate (PEGDA), poly(ethylene glycol) methyl ether acrylate, and ionic monomers. The ionic conductivity of the electrolytes is measured and interpreted in the context of differential scanning calorimetry and Raman spectroscopy measurements. A lithiated crosslinked electrolyte prepared with PEG₃₁DA and STFSI monomers is found to have a lithium ion conductivity of 3.2 × 10^-6 and 1.8 × 10⁻⁵ S/cm at 55 and 100 °C, respectively. The percentage of unpaired anions for this electrolyte was estimated at about 23% via Raman spectroscopy. Despite the large variances in metal cation – STFSI binding energies as predicted via DFT and large variations in ionic conductivity, STFSI-based crosslinked electrolytes with the same charge density and varying cations (Li, Na, K, Mg, and Ca) were estimated to all have unpaired anion populations in the range of 19 to 29%.

This paper presents a device for measuring and maintaining the constant water level in a tank. The device uses a capacity sensor to measure the water level. The sensor has a DC voltage output proportional to the water level in the tank. This voltage can be used in other automation too. The water level, in percentages, is displayed on a vu meter with 8 LEDs. The circuit for maintaining the constant level consists in a comparator with hysteresis. The level of the water is adjustable, using a reference voltage from a potentiometer (marked in percentages). The level of the water is compared with the prescribed level and the difference between them commands the start/stop of the water pump which supplies the tank through a relay. The device is powered by 220 V and is isolated from the environment.

The Golgi apparatus, long known for protein processing and vesicular trafficking, has recently emerged as an essential player in innate immune signaling pathways. This review article discusses our growing understanding of Golgi cells' roles in initiating and activating innate immunity pathways. We elaborate on the relevance of membrane connections between Golgi organelles and other organelles such as endoplasmic reticulum, mitochondria, endosomes, and autophagosomes that facilitate efficient access to innate immune signal transduction and subsequent effector responses. Additionally, we discuss microbial strategies that exploit the Golgi while diminishing its associated innate immune responses. By providing greater illumination of its multiple functions and mechanisms of operation, this article offers invaluable insight into how protein processing impacts innate immunity and vice versa.

Since electrical resistivity of concrete can be measured in a more rapid and simple way than chloride diffusivity, it should be primarily regular quality control of the electrical resistivity of concrete which provides the basis for indirect of quality control of concrete durability during the concrete construction. If this is realized, the electrical resistivity of concrete can be a crucial parameter to establish maintenance strategy for marine concrete structures. Electrical resistivity of concrete is important to estimate two processes involved in corrosion of reinforcement: initiation (chloride penetration) and propagation (corrosion rate). The resistivity of concrete structure exposed to chloride indicates the risk of early corrosion damage, because a low resistivity is related to rapid chloride penetration and to high corrosion rate. Concrete resistivity is a geometry-independent material property that describes the electrical resistance, which is the ratio between applied voltage and resulting current in a unit cell. The current is carried by ions dissolved in the pore liquid. While some data exist on the relationship between moisture content on electrical resistivity of concrete, very little research has been conducted to evaluate the effect of chloride on the conduction of electricity through concrete. The purpose of this study is to examine and quantify the effect of pore water and chloride content on surface electrical resistivity measurement of concrete. It was obvious that chloride content had influenced the resistivity of concrete and the relationship showed a linear function. That is, concrete with chloride ions had a comparatively lower resistivity. Chloride can lead to underestimate the electrical resistivity of concrete. Conclusively, this paper suggested the quantitative solution to depict the electrical resistivity of concrete with various chloride contents.

Repair mortar is commonly used to rehabilitate reinforced concrete structures or components that exhibit a relatively high level of distresses. Yet, this repair mortar can be contaminated by salt from its service environment. This work employs a two-dimensional finite element model to investigate the transport behavior of ionic species in salt-contaminated and water-saturated repair mortar under an externally applied electric field. The model was experimentally validated and then utilized to evaluate the effectiveness of electrochemical chloride extraction (ECE) with or without electrical injection of corrosion inhibitor (EICI). In the case study, both the ECE alone and the ECE+EICI treatment was found effective in decontaminating the zone in front of the steel rebar. In both techniques, the magnitude of current density has a significant effect on removing chloride out of the mortar and increasing the pH of the pore solution near the rebar, whereas the treatment time any not have a significant effect under some scenarios. The injection of the organic corrosion inhibitor significantly slowed down the removal of chloride. Changes in the ionic distribution in the mortar were generally beneficial in reducing the corrosion risk of the steel rebar and thus extending the service life of the repair mortar.

Radiotherapy using accelerated charged particles is rapidly growing worldwide. About 85% of the cancer patients receiving particle therapy is irradiated with protons, which have physical advantages compared to X-rays but similar biological response. In addition to the ballistic advantages, heavy ions present specific radiobiological features that can make them attractive for treating radioresistant, hypoxic tumors. An ideal heavy ion should have lower toxicity in the entrance channel (normal tissue), and being exquisitely effective in the target region (tumor). Carbon ions have been chosen because they represent the best combination in this direction. Normal tissue toxicities and second cancer risk are similar to those observed in conventional radiotherapy. In the target region, they have increased relative biological effectiveness and reduced oxygen enhancement ratio compared to X-rays. Some radiobiology properties of densely ionizing carbon ions are so distinct from X-rays and protons that they can be considered as a different “drug” in oncology, and may elicit favorable responses such as increased immune response and reduced angiogenesis and metastatic potential. The radiobiological properties of carbon ions should guide patient selection and treatment protocols to achieve optimal clinical results.

The metastatic disease is a complex and sequential process that involves the migration of tumor cells from the primary site to distant areas. This metastatic pathway is not always predictable. Therefore, this paper presents three rare cases of unusual metastases, due to their primary site: two metastases of a clear cell renal cell carcinoma, one gingival and one nasal, as well as a mandibular metastasis of a hepatocellular carcinoma. In all cases, an incisional biopsy was performed in order to sign out the diagnosis. After microscopical examination of morphological Hematoxylin and Eosin stained slides, for all cases, immunohistochemical reactions were performed to support the primary tumor site. Two cases had a previous histopathological diagnosis of a primary tumor, while for the third case, the metastatic lesion represented the first manifestation of the neoplastic disease, with an unfavorable prognosis.

Background: Trans-septal endocardial left ventricle lead placement is an alternative technique used capture the left ventricular endocardially but it is use is limited due lack of evidence, practice uptake and clinical trials. we evaluated the efficiency of the procedure, post procedural complication rate, rate of thromboembolic events as well as changes in echocardiographic parameters, brain natriuretic peptide (BNP) level and the New York Heart Association (NYHA) class. Results: TSLV lead implant is safe, improves ejection fraction, LVEDV, LVESV, LVIDd. Significantly reduces NTproBNP levels and NYHA class. Stroke rate was reported only in one patient (9%), noticeably, this particular patient was on DOAC rather than anti-vitamin K antagonists. In this group, patients, who were on Warfarin , were not reported to have any thrombo-embolic events. Discussion: Trans-septal endocardial LV lead implant in patients with a failed CS approach remains a viable alternative however, there is a higher risk of stroke amongst these patients, as well as more procedure related risk of complications compared to conventional CRT. The data analysis demonstrates that patients undergoing a TSLV lead implant due to a failed trans-venous approach have more advanced heart failure, defined by their higher NYHA class compared to conventional trans-venous CRT implant groups. Their pre TSLV implant, echocardiographic parameters are also worse compared to trans-venous CRT implant group

The relation between CO2 emissions and atmospheric CO2 concentration has traditionally been treated with more or less complex models with several boxes. Our approach is motivated by the question of how much CO2 must necessarily be absorbed by sinks. Observations lead to the model assumption, that carbon sinks like oceans or biosphere are linearly dependent on CO2 concentration on a decadal scale. In particular this implies the falsifiable hypothesis that oceanic and biological CO2 buffers have not significantly changed in the past 50 years and are not saturated in the forseeable future. The simple model with 2 parameters explains very well the CO2 emission and historical CO2 concentration data. The model gives estimates of the natural emissions, the pre-industrial CO2 equilibrium concentration levels, the half-life time of an emission pulse, and the future CO2 concentration level from a given emission scenario. This is validated by an ex-post forecast of the last 20 years. The important result is that with the stated polices scenario of the IEA future CO2 concentrations will not rise above 475 ppm. The model is compared with the Carbon modul of the Bern model, mapping their complex IRFs to a single time variant parameter.

As a hazardous waste, pickling waste liquor must be properly treated. An alternative consists in promoting the formation of ferrous salts from this residue, due to its higher ferrous content. Since FeCl2·4H2O is widely used in several applications, obtaining pure crystals of this material appears to be an interesting prospect. However, this compound has scarcely been investigated. In the present work, FeCl2·4H2O crystals have been obtained from pickling waste liquors. Their structural and morphological characteristics have been investigated by X-ray diffraction, scanning electron microscopy as well as Mössbauer spectroscopy. In addition, the photoluminescence study of the obtained samples was also assessed. It was observed that after some aging time, the obtained crystals change in colour from green to more yellowish. So, the aged sample has also been evaluated, and their structural characteristics are compared with the original crystals. Despite this, the obtained crystals exhibit a FeCl2·4H2O structure, which is not modified with the aging of the sample.

This study conducts a comprehensive review of the integration of Hybrid Electric Turbochargers in mass-produced road vehicles. The primary objective is to inform the readers about the potential advantages and innovative applications of HETs. Employing a SWOT analysis, the research compares the performance of HETs on thermal engines versus traditional turbochargers and HETs on thermal engines versus HETs on hybrid engines based on a synthesis of multiple research findings. The study elucidates the fundamental mechanics of turbochargers, emphasizing their inherent benefits. Additionally, it introduces a novel approach with the integration of the hy-brid-electric turbocharger, demonstrating its capacity, supported by practical examples. The in-corporation of turbochargers with energy recovery mechanisms, including HETs, is shown to significantly contribute to emissions reduction. Moreover, the electric drive facilitates the utili-zation of hybrid turbines, particularly on low-displacement engines, resulting in enhanced effi-ciency, torque, and liter power. In conclusion, the research underscores the potential of HETs to substantially mitigate the environmental impact of the transportation sector by reducing emis-sions and conserving energy. Their ability to optimize the fuel efficiency and power output of internal combustion engines, coupled with the feasibility of downsized engines, positions HETs as an attractive option for both manufacturers and consumers. However, it is acknowledged that the implementation of HETs is in its early stages, necessitating further research to comprehensively understand their environmental impact. Despite this, the promising positive impact on the en-vironment designates HETs as a technology deserving close attention in the forthcoming years.

Chloride (Cl-) is applied in coffee in rates as a “macronutrient” due that potassium (K+) is one of the most demanded nutrients by the coffee plant, and the potassium muriate (KCl) bases fertilizer is one the most used by the coffee growers. Does not exist scientific evidence that addresses the question regarding with which is the influences of the Cl- applied in the K fertilization base on MOP on coffee growth, nutrient uptake, and nitrogen use efficiency (NUE). Over four years, two trials were conducted on greenhouse and field conditions to address these questions. The trials set up were designed to test the influence of increased Cl- and reduced S rates on biomass accumulation, nutrient uptake, and NUE. A significant effect of the Cl- rates on growth was observed under greenhouse conditions but a non-significant effect on yield under field conditions. Cl- and S significantly influence the NUE in coffee. The result allows us to conclude that Cl- rates need to be balanced with S rates and that Cl- applied as a macronutrient can improve the NUE in coffee when those rates do not exceed 180 mg. L-1 Cl- and 80 mg.L-1 S in the greenhouse and 150 kg.ha-1.year-1 Cl- and 50 kg. ha-1.year-1 S in field conditions. In practical terms, coffee farmers need to balance the K base fertilizers sources to improve the nutrient use efficiency, especially the NUE.

The SLC12 family of cation-chloride-cotransporters (CCCs), comprising potassium chloride cotransporters (KCCs)-mediated Cl- extrusion relative to sodium chloride cotransporters (NKCCs)-mediated Cl- loading, play vital roles in cell volume regulation and ion homeostasis. These functions of the CCCs influence a variety of physiological processes, many of which overlap with the pathophysiology of cardiovascular disease. Although not all of the cotransporters have been linked to Mendelian genetic disorders, recent studies have provided new insights into their functional role in vascular and renal cells along with their contribution to cardiovascular diseases. Particularly, an imbalance in potassium levels promote the pathogenesis of atherosclerosis and disturbances in sodium homeostasis are one of the causes of hypertension. Recent findings even suggest hypothalamic signalling as a key signalling pathway in the pathophysiology of hypertension. In this review, we summarize and discuss the role of CCCs in cardiovascular disease with particular emphasis on knowledge gained in recent years on NKCCs and KCCs.

Iodide is an essential micronutrient present in very small quantities in the human body, with a fundamental action for the adequate synthesis of thyroid hormones, which are critical for cell differentiation, growth and metabolism. In the form of iodide, iodine is widely distributed in the environment, although in an irregular manner, occurring in abundant amounts in the oceans and in coastal areas and scarcely found on islands and mountains. The diet is the main source of iodine, whose intake varies according to the amount present in soil and water and according to eating habits. Governmental policies have been adopted to satisfy and guarantee the necessary daily supply of iodine, such as fortification of industrialized salt for domestic iodine consumption or addition to the bread commonly consumed in a given region, or the offer of iodized oil to the population, or even iodine supplementation through medications. Iodide deficiency is the main avoidable cause of brain damage to fetuses and children, as well as retardation of psychomotor development. Thyroid hormones are almost universally involved in the development and proliferation of fetal neural tissue. Permanent lesions of the cerebral cortex, hippocampus and cerebellum may occur, with loss of, or damage to the brainstem or spinal cord, affecting cortical areas that integrate highly specialized stimuli, which become poorly defined on an anatomical basis, including silent areas of the associative cortex. One of the more significant metabolic problems due to dietary iodine deficiency is the presence of goiter (increased volume of the thyroid gland). Thyroid carcinoma is the most frequent endocrine neoplasia affecting the human species and plasma iodine concentration is related to the development of specific subtypes of this neoplasia. An increased prevalence of follicular carcinoma, a more aggressive tumor, has been observed in areas of iodine deficiency, while the correction of this deficiency is associated with a higher prevalence of papilliferous carcinoma, a less aggressive form. CONCLUSION: An ideal plasma iodide concentration is necessary to insure the proper mental development of fetuses and young children and to minimize the aggressiveness of thyroid cancer from follicular cells in humans.

1) Landsat operational land imager (OLI) data and consequent laboratory measurements were used to predict Chlorophyll-a (Chl-a) concentration and the trophic states for an inland lake within the East Kolkata Wetland, India; 2) The most suitable band ratio was identified by performing Pearson correlation analysis between Chl-a concentrations and possible OLI band and band ratios from the study points; 3) The results showed highest correlation coefficient from the band ratio OLI5/OLI4 with an R value of 0.85. The prediction model was then developed by applying regression analysis between the band ratio OLI5/OLI4 and Chl-a concentration of the study points. The reflectance ratios of the validation points were given as input on the prediction model and the model output was considered as predicted Chl-a values of the validation points to check the efficiency of the prediction model. The regression model between laboratory-derived Chl-a value and model-fitted Chl-a value of the validation points revealed a high correlation with an R² value of 0.78. Trophic State Index (TSI) of the lake was also calculated from laboratory-derived Chl-a value and model-fitted Chl-a value of the validation points. The study presented a high correlation of TSI determined from predicted data with TSI from laboratory reference data (R = 0.88). The TSI values of the lake ranged from 65 to 75 which indicate that the lake is appeared to be eutrophic to hypereutrophic conditions. 4) This empirical study showed that Landsat 8 OLI imagery can be effectively applied to estimate Chl-a levels and trophic states for inland lakes.

It is known that ammonium has a higher permeability through anion-exchange and bipolar membranes compared to K+ cation that has the same mobility in water. However, the mechanism of this high permeability is not clear enough. We develop a mathematical model based of the Nernst-Planck and Poisson equations for diffusion of ammonium chloride through an anion-exchange membrane; proton exchange reactions between ammonium, water and ammonia are taken into account. It is assumed that ammonium, chloride and OH− ions can only pass through membrane hydrophilic pores, while ammonia can also dissolve in membrane matrix fragments not containing water and diffuse through these fragments. It is found that due to the Donnan exclusion of H+ ions as coions, the pH in the membrane internal solution increases when approaching the membrane side facing distilled water. Consequently, there is a change in the principal nitrogen-atom carrier in the membrane: in the part close to the side facing the feed NH4Cl solution (pH<8.8), it is the NH4+ cation, and in the part close to distilled water, NH3 molecules. The concentration of NH4+ reaches almost zero at a point close to the middle of the membrane cross-section, which approximately halves the effective thickness of the diffusion layer for the transport of this ion. When NH3 takes over the nitrogen transport, it only needs to pass through the other half of the membrane. Leaving the membrane, it captures an H+ ion from water, and the released OH− goes towards the membrane side facing the feed solution to meet the NH4+ ions. The comparison of the simulation with experiment shows a satisfactory agreement.

Recent advances in synthetic membranes allow their use in fields as diverse as food and agriculture, biotechnology, industrial wastewater treatment, and potable water production. Among the newly developed technologies, nanofiltration for liquids and more particularly for desalination of seawater or saline aquifers are actively pursued. However, current solid-state membranes performance is limited, which calls for the development of novel formulations for membranes offering both high permeability (ion and water flux) and ion differentiation (selectivity), usually considered antagonist features. We report the development of hybrid nanoporous membranes made of solid-state polymeric carbonate track-etched (PCTE) thin films in which biological ion channels such as Gramicidin A (GA), alpha-hemolysin (α-HL), and outer-membrane protein F (OmpF) aquaporin are confined and graphene oxide (GO) conjugated cobalt ion selective binding peptide motifs (Copep) are adsorbed, referring as bioinspired and biomimetic approaches, respectively. These solid-state nanoporous membranes are attracting widespread attention since they offer scalability, mechanical robustness, selectivity, controlled pore dimension and shape, for water sustainability. The ion permeability, ion diffusion coefficient and selective ion recognition are evaluated via nanofiltration, cell diffusion kinetics, and UV-Visible absorption spectroscopy to gain insights into the role of key performance parameters including effective ion confinement in track-etched pores, rich surface chemistry, and peptide-induced channel for selective ion transport. These findings provide new avenues for artificial ion channels by synergistic combination of eco-friendly material design such as GO enabled by bio-molecular recognition chemistry.

This study examines the absorption and concentration of anthracene (AN) in the garden radish. Studies were conducted to grow radishes from the sowing stage in soil contaminated with AN, and to grow radishes in soil contaminated with AN following maturity (27 days after sowing). For the growth in AN-containing soil from sowing onward, AN levels immediately after seeding ranged from 12,500-36,300 ng/g-ww. AN concentrations during growing period ranged from 7140-16,000 ng/g-ww in soil and from 38.2-2160 ng/g-ww in radish, respectively. For the growth in AN-containing soil after maturity, AN concentrations in soil and radish ranged from 9560-22,100 ng/g-ww and 342-2270 ng/g-ww. The concentrations of AN in the roots and leaves had a higher density than those in the stems. In these experiments, positive relationships between AN levels in soil and radishes were observed. It is inferred that the greater the degree of soil contamination, the greater the effect on the amount of AN assimilated by the radishes. The concentration ratio (radish-to-soil; Cr/Cs) decreased exponentially with days since AN application. This indicates that the concentration ratio is affected by time in contact with AN. According to the results for the change over time of Cr/Cs and contents by radish part, it is thought that AN in the soil has good absorption through the roots to circulate within the organism, and is preferentially distributed and accumulated in the roots and leaves, which have high organic matter content.

Polyvinyl chloride (PVC) electric wires were subjected to dechlorination in subcritical water at three different temperatures in a high-pressure reactor. About 2.09, 73.08 and 95.96 wt. % of chlorine in PVC wires was removed during dechlorination at 200, 250 and 300 °C, respectively. The solid residues were analyzed and characterized by thermogravimetry, at three different heating rates (5, 10 and 20 °C/min) in inert and oxidizing atmosphere. With the purpose of studying the emission of chlorinated pollutants, pyrolysis experiments at 850 °C were also performed in a laboratory scale reactor with the dechlorinated materials, as well as with the original PVC electric wire. Polycyclic aromatic hydrocarbons (PAH) formation increased, but chlorobenzenes (ClBz) and chlorophenols (ClPh) formation decreased as the temperature of dechlorination increased; naphthalene was the most abundant PAH and monochlorobenzene and monochlorinated phenols (3-+4-) were the most abundant chlorinated compounds.

We used LA-ICP-MS U-Pb data for detrital zircon to constrain the Maximum Depositional Age (MDA) and provenance of clastic sedimentary rocks of the Volyn-Orsha sedimentary basin, which filled an elongated (~625×250 km) depression in SW Baltica and attained ~900 m in thickness. Eighty-six zircons out of one hundred and three yielded concordant dates, with most of them (86 %) falling in the time interval between 1655 ± 3 and 1044 ± 16 Ma and clustering in two peaks at ca. 1630 and 1230 Ma. The remaining zircons yielded dates older than 1800 Ma. The MDA is defined by a tight group of three zircons with a weighted average age of 1079 ± 8 Ma. This age corresponds to the time of a clockwise ~90° rotation of Baltica and the formation of the Grenvillian – Sveconorwegian – Sunsas orogenic belts. Subsidence was facilitated by the presence of eclogites derived from subducted oceanic crust. The sediments of the Orsha sub-basin in the northeastern part of the basin were derived from the local crystalline basement, whereas the sediments in the Volyn sub-basin, extending to the margin of Baltica, were transported from the orogen between Laurentia, Baltica, and Amazonia.

Reduced-order electrothermal models play a key role in the design and control of lithium- ion cell stacks, calling for accurate model parameter calibration. This paper presents a complete electrical and thermal experimental characterization procedure for coupled modeling of cylindrical lithium-ion cells in order to implement them in a prototype Formula SAE hybrid racing car. The main 4goal of the tests is to determine cell capacity variations with temperatures and discharge currents, to predict the open circuit voltage of the cell and its entropic component. A simple approach for the characterization of the battery equivalent electrical circuit and a two-steps thermal characterization method are also shown. The investigations are carried out on four commercial 18650 NMC lithium cells. The model demonstrated to predict the battery voltage at a RMS error lower than 20mV and the temperature to a RMS error equal to 0.5 ◦C. The authors hope that this manuscript can contribute to the development of standardized characterization techniques for such cells, while offering experimental data and validated models that can be used by researchers and BMS designers in different applications.

This paper evaluates the potential of solar concentration technologies—compound parabolic collector (CPC), linear Fresnel collector (LFC) and parabolic trough collector (PTC)—as an alternative to conventional sources of energy for industrial processes in Latin America, where high levels of solar radiation and isolated areas without energy supply exist. The analysis is addressed from energy, economic and environmental perspective. A specific application for Argentina in which fourteen locations are analyzed is considered. Results show that solar concentration technologies can be an economically and environmentally viable alternative. Levelized cost of energy (LCOE) ranges between 2.5 and 16.9 c€/kWh/m² and greenhouse gas (GHG) emissions avoided range between 33 and 348 kgCO₂/(m²·year). CPC technology stands out as the most recommendable technology when the working fluid temperature ranges from 373K to 423K. As the working fluid temperature increases the differences between the LCOE values of the CPC and LFC technologies decrease. When 523K is reached LFC technology is the one which presents the lowest LCOE values for all analyzed sites, while the LCOE values of PTC technology are close to CPC technology values. Results show that solar concentration technologies have reached economic and environmental competitiveness levels under certain scenarios, mainly linked to solar resource available, thermal level requirements and solar technology cost.

We report on the successful preparation of wet dressings hydrogels based on Chitosan-Poly(N-Vinyl-Pyrrolidone)-Poly(ethylene glycol)-Poly(acrylic acid) and Poly(ethylene oxide) by e-beam cross-linking in weakly acidic media, to be used for rapid healing and pain release of infected skin wounds. The structure and compositions of hydrogels investigated according to sol-gel and swelling studies, network parameters, as well as FTIR and XPS analyses showed the efficient interaction of the hydrogel components upon irradiation, maintaining the bonding environment while the cross-linking degree increasing with the irradiation dose and the formation of a structure with the mesh size in the range 11-67 nm. Hydrogels with gel fraction above 85% and the best-swelling properties in different pH solutions were obtained for hydrogels produced with 15 kGy. The hydrogels are stable in the simulated physiological condition of an infected wound and show appropriate moisture retention capability and the water vapor transmission rate up to 272.67 g m-2 day-1, to ensure fast healing. The hydrogels proved to have a significant loading capacity of ibuprofen (IBU), being able to incorporate a therapeutic dose for the treatment of severe pains. Simultaneously, IBU was released up to 25% in the first 2h, having a release maximum after 8h.

Background: It is known that Preeclampsia affects the lactogenesis. However, data on effects of this pathology on the human milk neurobiomarkers composition are not available. The aim of this study is to investigate the effects of this gestational pathology on Activin A levels, a neurobi-omarker known to play an important role in the development and protection of the central nerv-ous system. Methods: The women recruited were divided in two different study groups: preeclamptic or normotensive women. All the human milk samples were collected using the same procedure. Activin A was quantified using an ELISA test. To investigate the effect of Preeclampsia on the Activin A concentration in the 3 lactation phases, mixed linear model with unistructural covariance structure, mother as random effect, and fixed effects were performed. Results: Activin A was detected in all samples. There were no significant differences between Preeclamptic and Normotensive women. The only significant effect is related to the lactation phase: it is significant the difference between colostrum and mature milk (p<0.01). In conclusion these results allow us to affirm that breast milk beneficial properties are maintained even if preeclampsia occurs.

Wound healing involves physical, chemical and immunological processes. Transient receptor potential (TRP) and other ion channels are implicated in epidermal re-epithelization. Ion movement across ion channels can induce transmembrane potential that leads to transepithelial potential (TEP) changes. TEP present in epidermis surrounding the lesion decreases and induces an endogenous direct current generating an epithelial electric field (EF) that could be implicated in wound re-epithelialization. TRP channels are involved in the activation of immune cells during the inflammatory phase of wound healing. The aim of the study was to review the mechanisms of ion channel involvement in wound healing in in vivo experiments in rodents (mice, rats, rabbits) and how can this process be influenced. This review used the latest results published in scientific journals over the last year and this year to date (1 January 2023–31 December 3000) in order to include the in-press articles. Some types of TRP channels, such as TRPV1, TRPV3, and TRPA1, are expressed in immune cells and can be activated by inflammatory mediators. The most beneficial effects in wound healing are produced using agonists of TRPV1, TRPV4 and TRPA1 channels or by inhibiting with antagonists, antisense oligonucleotides or knocking down TRPV3 and TRPM8 channels.

The purported cognitive benefits associated with nicotine and its metabolites in the brain are a matter of debate. In this review, the impact of the pharmacologically active metabolite of a nicotine derivative produced by bacteria (6-hydroxy-L-nicotine) on memory, oxidative stress, and the activity of the cholinergic system in the brain was examined. A search in the PubMed, Science Direct, Web of Science, and Google Scholar databases, limiting entries to those no later than July 2023, was conducted. The search focused specifically on articles pertaining to nicotine metabolites, memory, oxidative stress, cholinergic system activity, as well as enzymes or pathways related to nicotine degradation in bacteria. The preliminary search resulted in 696 articles, and following the application of exclusion criteria, 185 articles were deemed eligible for inclusion. This review focuses on experimental studies supporting nicotine catabolism in bacteria, and the chemical and pharmacological activities of nicotine and its metabolite 6-hydroxy-L-nicotine.

In the electric distribution systems, the “Smart Grid” concept is implemented to encourage energy savings and integration of the innovative technologies, helping the Distribution Network Operators (DNOs) in choosing the investment plans which to lead the optimal operation of the networks and increasing the energy efficiency. In this context, a new phase load balancing algorithm was proposed to be implemented in the low voltage distribution networks with hybrid structures of the consumption points (switchable and non-switchable consumers). It can work in both operation modes (on-line and off-line), uploading information from different databases of the DNO which contain: the consumers’ characteristics, the real loads of the consumers integrated into the Smart Metering System (SMS), and the typical load profiles for the consumers non-integrated in the SMS. The algorithm was tested in a real network, having a hybrid structure of the consumption points, on a time interval by 24 hours. The obtained results were analyzed and compared with other algorithms from the heuristic (Minimum Count of Loads Adjustment algorithm) and the metaheuristic (Particle Swarm Optimization and Genetic Algorithms) categories. The best performances were provided by the proposed algorithm, such that the unbalance coefficient resulted in the smallest value (1.0017). The phase load balancing led to the following technical effects: decreasing the average current in the neutral conductor with 94% and for the energy losses with 61.75 %, and increasing the minimum value of the phase voltage at the farthest pillar with the 7.14 %, compared to the unbalanced case.

The present study concerns the application of electrochemical chloride extraction to concrete designed with partial replacements of Ordinary Portland Cement (OPC) from different binders, namely ground granulated blast furnace (GGBS), pulverized fly ash (PFA) and Silica Fume (SF), to attend the need of corrosion repair for modern constructions. Electrochemical Chloride Extraction (ECE) was applied to the specimens at a current density of 2A/m2 for 4 weeks. The chloride types and binding mechanisms appeared to have important implications on the different performance of treatment perceived for all binders. Considering total chlorides, removal was more significant for OPC and GGBS when compared to others. The main difference noted was that for GGBS the removal of bound chlorides was more significant due to a possible release of adsorbed chlorides from the silicate hydrates, present at higher intensities in this case. However, even though GGBS had greater rates of bound chloride removal it had still the same percentage as OPC for total efficiency due to the fact that in OPC the removal of free chlorides is more expressive.

Biocidal compositions based on interpolyelectrolyte complexes and a low molecular weight antibiotic can become a promising material for creating biocidal coatings, as they combine wash-off resistance and dual biocidal action due to the biocide and the polycation. Molecular mass characteristics of polymers play essential role in physics and mechanical properties of the coatings. In this work, the properties of polydiallyldimethylammonium chloride (PDADMAC) coatings of various molecular weights are investigated and assumptions are made about the optimal molecular weight needed to create antibacterial compositions. To study the resistance to washing off and moisture saturation of the coatings, the gravimetric method was used, the adhesive properties of the coatings were studied by dynamometry. It has been established that an increase in molecular weight affects the wash-off resistance of coatings, but does not affect moisture absorption and adhesion mechanics of coatings. All samples of PDADMAC were demonstrated to exhibit the same antibacterial activity. Thus, when developing systems for creating antibacterial coatings, it must be taken into account that in order to create stable coatings. The requirement to use PDADMAC with a high degree of polymerization is necessary for control the desorption of coating during wash off-but not mandatory for the control of mechanical and antibacterial properties of the coating.

The corrosion morphology in grade 2205 duplex stainless steel wire has been studied to understand the nature of pitting and the causes of the ferrite phase's selective corrosion in acidic NaCl solution. It is shown that the corrosion mechanism is always pitting, which either manifests lacy cover perforation or densely-arrayed selective cavities developing on the ferrite phase. Pits with a lacy metal cover form in concentrated chloride solutions, whereas the ferrite phase's selective corrosion develops in diluted electrolytes, showing dependency on the chloride-ion concentration. The pit perforation is probabilistic and occurs on both austenite and ferrite grains. The lacy metal covers collapse in concentrated solutions but remain intact in diluted electrolytes. The collapse of the lacy metal cover happens due to hydrogen embrittlement. Pit evolution is deterministic and occurs selectively in the ferrite phase in light chloride solutions.

Ion channels are integral membrane proteins that facilitate the movement of ions across cell membranes, playing a key role in a range of biological processes. The high cost and time required for wet lab experiments to characterize ion channels has spurred the development of computational methods for this purpose. In our previous work, we demonstrated the effectiveness of protein language models for ion channel prediction, using a logistic regression classifier to distinguish ion channels from non-ion channels (TooT-BERT-C) and transporters from non-transporters (TooT-BERT-T). In this study, we build upon this approach by using a combination of classical machine learning classifiers and a Convolutional Neural Network (CNN) with fine-tuned representations from ProtBERT, ProtBERT-BFD, and MembraneBERT to discriminate ion channels from non-ion channels. The results of our experiments demonstrate that TooT-BERT-CNN-C, a combination of the representations from ProtBERT-BFD and a CNN, outperforms existing state-of-the-art methods for predicting ion channels, with a Matthews Correlation Coefficient (MCC) of 0.86 and an accuracy of 98.35% on an independent test set.

In this study, the extraction of rare earth elements (REEs) from chloride solutions containing mixtures of these metals with solutions of the mixtures of P507 and Cyanex 272 (1:1) of various concentrations was experimentally studied. It was shown that the distribution coefficients of all REEs decrease with increasing concentration of these metals in the initial solution, which is associated with the loading of the organic phase. The most significant improvement in the extraction is observed for heavy group of rare earth elements. The extractability of REEs enhances with increasing atomic number of the element, as is typical for the extraction of these metals with acidic organophosphorus extractants. The data obtained show that separation factors of adjacent rare earth elements mainly decrease with increasing concentration of metals in the initial aqueous solution. Increasing the concentration of the extractant mixture does not have a significant effect on the values of the adjacent REE separation factors. Analysis of the experimental results shows that two commercial products can be obtained from a concentrate of the medium-heavy group. In the first cascade, yttrium can be separated, in the second, a concentrate of dysprosium and terbium can be obtained.

First of all the paper presents a solid solution of piezoelectric ceramic that was synthesized according to the general formula Pb(1-x)Srx(Ti0.48Zr0.52)(1-y)NbyO3 with x = 0.05 and y = 0.02, using wet ceramic processing technology and using an oxide mix as prime material. The effects of dopants (Sr2+ and Nb5+) on phase constitution, on microstructure and on the dielectric and piezoelectric properties were determinate. The Zr/Ti ratio was chosen near the morphotropic phase boundary of the PZT system in studied composition. The XRD data revealed that the PZT doped composition had tetragonal perovskite structure. Secondly the paper presents the design of the novel piezo-motor based on a surface wave which translates the linear extension of different piezoelectric segments of a piezoelectric cylinder into a rotational bending movement. This rotational bending of the piezoelectric cylinder is then transformed into a continuous rotation of the rotor through a calculated contact. The design of the motor takes advantage of the high piezoelectric constants of the developed material in an optimal way in order to increase the energetic efficiency. A brief mathematical model of electromechanical answer of piezoelectric materials is presented as it was used in the modeling of the material during the numerical simulations.

This study examines the effectiveness of a comprehensive psychomotor development program combined with adapted football training for adolescents diagnosed with intellectual disabilities in Romania. Twelve participants, with a mean age of 17.42 years underwent a carefully designed intervention program spanning 36 weeks. The program aimed to enhance fundamental movement skills, integrate these skills into specialized football training, and culminate in a Unified 7-a-side Football Match. Results indicate significant improvements in psychomotor skills, including static and dynamic balance, pulse processing speed, and identified stimuli. Moreover, the intervention positively impacted social interaction among participants. Statistical analysis, employing Pearson Correlation Analysis and Paired Samples t-Test (One-Sample), compared assessments. Results revealed significant differences between pre- and post-intervention measurements, providing robust evidence of the program's efficacy. The positive correlations between physical parameters and social interaction highlight the interconnectedness between physical fitness and social engagement. Our findings suggest that improvements in physical abilities may contribute to increased social interaction among children with intellectual disabilities, underscoring the holistic nature of our intervention, which addresses multiple dimensions of development simultaneously. The findings underscore the holistic benefits of integrating psychomotor development and adapted football programs for adolescents with intellectual disabilities, emphasizing the importance of promoting inclusive physical activities for their overall well-being.

In time, osteoarthritis (OA) generates the misalignment of the affected joint structures. However, due to the nature of bipedal gait, OA in the lower limb can also cause pathological gait patterns, which can generate instability and falls, with great consequence, especially in the aged population. With goniometry used to evaluate the range of motion of joints (ROM), we wanted to evaluate how gender impacts gait dynamics in OA patients. For this study we have compared 106 OA patients (male=32, female=74) to age matched controls. All participants had their right leg as dominant. Video recording of normal gait was analysed with a digital goniometry tool phone application, and the knee’s ROM was measured in midstance and midswing of the gait. During midstance, significant extension and flexion of the knee excursion have been observed in both males and females. During midswing, knee OA presents more differences, whereas subjects with hip and knee OA present changes on the dominant knee. Midstance changes suggest that the knee’s joint degenerative changes can be linked to hip OA secondary changes. Midswing changes in lower limb OA suggest a connection to the activities of daily life. Gender differences generated by OA must furthermore be studied in both lower limbs so that the best therapeutic approach can be chosen.

Background: Previous papers have developed a statistical mechanics of neocortical interactions (SMNI) fit to short-term memory and EEG data. Adaptive Simulated Annealing (ASA) has been developed to perform fits to such nonlinear stochastic systems. An N-dimensional path-integral algorithm for quantum systems, qPATHINT, has been developed from classical PATHINT. Both fold short-time propagators (distributions or wave functions) over long times. Previous papers applied qPATHINT to two systems, in neocortical interactions and financial options. Objective: In this paper the quantum path-integral for Calcium ions is used to derive a closed-form analytic solution at arbitrary time that is used to calculate interactions with classical-physics SMNI interactions among scales. Using fits of this SMNI model to EEG data, including these effects, will help determine if this is a reasonable approach. Method: Methods of mathematical-physics for optimization and for path integrals in classical and quantum spaces are used for this project. Studies using supercomputer resources tested various dimensions for their scaling limits. In this paper the quantum path-integral is used to derive a closed-form analytic solution at arbitrary time that is used to calculate interactions with classical-physics SMNI interactions among scales. Results: The mathematical-physics and computer parts of the study are successful, in that there is modest improvement of cost/objective functions used to fit EEG data using these models. Conclusions: This project points to directions for more detailed calculations using more EEG data and qPATHINT at each time slice to propagate quantum calcium waves, synchronized with PATHINT propagation of classical SMNI.

Plasma plays an important role in semiconductor processes. With the recent miniature and integration, the control of plasma became essential for the success in critical dimension of a few nanometers and etch narrow and deep holes with high aspect ratios. Recently, the etching process has reached physical limitations due to a significant increase in wafer surface temperature under the elevated amount of RF power, affecting not only the warpage phenomenon but also etching uniformity and etching profiles. Therefore, the plasma characteristics are identified using invasive single Langmuir probe (SLP) for wafer temperature diagnosis. Optical data is obtained through a non-invasive optical emission spectroscopy (OES) and the plasma parameters are derived to compare and verify with the SLP. Two variables, electron temperature and electron density, are substituted for the heat flux formula to derive the heat flux according to its location. Using a wafer-type temperature sensor, check the derived heat flux values and compare trends. Such studies are expected to be able to calculate heat flux values in real time, anticipate wafer temperatures, and solve existing problems.

As a model for economic and ecological systems, replicator dynamics represents a basic form of agent competition for finite resources. Here, we investigate the effects of stochastic resetting in this kind of processes. Random reset events abruptly lead individual resources to a small value from which dynamics must start anew. Numerical results show that resource distribution over the population of competing agents develops highly nonuniform profiles, exhibiting clustering and fluctuations with anomalous dependence on the population size. This non-standard statistical behavior jeopardizes an analytical treatment based on mean-field assumptions. We propose alternative simplified analytical approaches which provide a stylized description of entropy evolution for the clustered distribution of resources and explain the unusually slow decrease of fluctuations.

To achieve efficient utilization of low-concentration mine gas, reduce resource waste, and alleviate environmental pollution, high-temperature oxidation of low-concentration gas at a concentration range of 1.00% to 1.50% that is directly discharged into the atmosphere during coal mine production was oxidized to recover heat for reuse. The gas oxidation equipment was improved for the heating process, and the safety of low-concentration gas oxidation under high-temperature environment was evaluated. Experimental results showed that the reactor could provide a 1000 ℃ high-temperature oxidation environment for gas oxidation after installing high-temperature resistant ceramics. The pressure variation curves of the reactor with air and different concentrations of gas were similar. Due to the thermal expansion, the air pressure slightly increased and then returned to normal pressure. In contrast, the low-concentration gas exhibited a stable pressure response in the high-temperature environment of 1000 ℃. The outlet pressure was significantly greater than the inlet pressure, and the pressure difference between the inlet and outlet exhibited a trend to increase with the gas concentration. The explosion limit varied with the temperature and the blend with oxidation products. The ratio of measured gas pressure to air pressure after oxidation was below the explosion criterion, indicating that the measured concentration gas is still safe after the shift of explosion limit, which provides a safe concentration range for efficient use of low-concentration gas in the future.

Silver and gold nanoparticles are a promising tool for medical and industrial application, therefore, their ecotoxicity should be carefully examined. The effect of silver (12 nm) and gold (4.7) nanoparticles coated with polyethylene glycol on Spirulina platensis biomass growth and biochemical composition was investigated. The spirulina cultivation medium was supplemented with nanoparticles in concentration range 0.025-0.5 µM. Given concentrations stimulated spirulina biomass growth, while content of proteins, carbohydrates and auxiliary pigments was affected insignificantly by presence of nanoparticles in cultivation medium. The pronounced effect of gold nanoparticles at concentration 0.5 µM on the lipids content was observed. TEM images demonstrate that nanoparticles penetrate inside the cell, resulting in ultrastructural changes in cells.

The research on calcium leaching of 3D printed cement pastes (3DPC) exposed in aggressive water is limited, and the mechanism underlying its effect needs to be better understood. The performance anisotropy of degraded 3DPC due to calcium leaching is investigated in this paper. Samples with aggregate micro fines (AMF) and fly ash (FA) were prepared. A 6 mol/L NH₄Cl solution was used in the accelerated experiment. At specific leaching durations, performances were tested on the samples in different leaching directions. Results show that the performances of 3DPC in aggressive water have a significant anisotropic behavior. The evolution of pore defects and hydration products mainly governs the performance anisotropy of degraded 3DPC. The remaining hydration products of the surface of 3DPC leached in the Z direction are less than the other two directions because calcium ions leached in the Z direction are difficult to be compensated through weak interfaces between layers.

Background: This is a comparative analysis of upgrade to cardiac resynchronisation therapy (CRT) of an existing pacemaker implanted for bradyarrhythmia or an implantable cardioverter defibrillator (ICD). International guidelines recommend an upgrade to CRT for both groups based on the same criteria; this may lead to a hypothesis of whether we are under-treating a population that would otherwise benefit more from a CRT than the other. Methods: So far, this is the largest multicentre retrospective study that includes in total, 151 (93 upgrades to CRT-P and 58 upgrades to CRT-D) participants who had an upgrade to a CRT device between January 2010 and January 2020. Clinical and echocardiographic parameters were analysed both, before and after an upgrade to CRT. Results: EF was greater in patients with PPM, both before and after upgrade. Moreover, the post upgrade increase in EF was significantly greater in patients with PPM. Patients with ICD have, on average, an NYHA class ranking greater than PPM patients, both before and after upgrade. Conclusions: These data show that the PPM group patients have a greater response to upgrade to CRT compared to those from the ICD group. It also demonstrates that patients with non-ischaemic cardiomyopathy are better responders compared to those with ischaemic aetiology.

Lithium-ion (Li-ion) batteries are becoming more common in portable electronic devices due to their high energy density, lack of memory effect, and high charge and discharge rate capabilities. Li-ion batteries are a relatively new technology, first marketed in the early 1990s, and research and development work are ongoing to improve safety and increase capacity, charge/discharge rate, and lifetime [1]. In this paper, we review the types and characteristics of Li-ion batteries and summarize charging methods and safety considerations. Following, we design and fabricate Li-ion battery and highlight the steps of fabrication that ensure fast charge/discharge rates that give the battery more reliability and high energy density

Boron (B) is considered a prebiotic chemical element with a role in both the origin and evolution of life, as well as an essential micronutrient for plants, some bacteria, fungi, and algae. B has beneficial effects on the biological functions of humans and animals, such as reproduction, growth, calcium metabolism, bone formation, energy metabolism, immunity, brain function, and steroid hormones. In the future, naturally organic B (NOB) species may become promising novel prebiotic candidates. We included the most relevant works about NOB species, starting from our 30-year research experience. NOB-containing compounds have been shown essential for the symbiosis between different kingdoms. New insights into the essentiality of NOB species for healthy symbiosis between the human/animal host and the microbiota will determine the use of natural B-based nutraceuticals to target the colon (colonic foods). The mechanism of action (MoA) of NOB species is related to both the B signaling molecule [autoinducer-2–borate (AI-2B)], as well as the fortification of the colonic mucous gel layer with NOB species from the specific prebiotic boron-rich diet. Therefore, both microbiota and the mucous gel layer of the colon become the NOB species’ target. This paper reviews the evidence supporting the essentiality of the NOB species on the symbiosis between the microbiota and the human/animal host with the stated aim of highlighting the MoA and target of these species.

Salinity substantially affects plant growth and crop productivity worldwide. Plants adopt several biochemical mechanisms including regulation of antioxidant biosynthesis to protect themselves against the toxic effects induced by the stress. One-year-old Pistachio rootstock exhibiting different degrees of salinity tolerance were subjected to sodium chloride induced salt stress to identify genetic diversity among cultivated pistachio rootstock for their antioxidant responses, and to determine the correlation of these enzymes to salinity stress. Leaves and roots were harvested following NaCl-induced stress. Results show that a higher concentration of NaCl treatment induced oxidative stress in the leaf tissue and to a lesser extent in the roots. Both tissues showed an increase in ascorbate peroxidase, superoxide dismutase, catalase, glutathione reductase, peroxidase and malondialdehyde. Responses of antioxidant enzymes were cultivar dependent, as well as temporal and dependent on the salinity level. Linear and quadratic regression model analysis revealed significant correlation of enzyme activities to salinity treatment in both tissues. The variation in salinity tolerance reflected their capabilities in orchestrating antioxidant enzymes at the roots and harmonized across the cell membranes of the leaves. The study provides a better understanding of root and leaf coordination in regulating the antioxidant enzymes to NaCl induced oxidative stress.

Shrubs are a significant component of urban vegetation residing in parks, but they experience various influences of biotic and abiotic agents, among which aphids play an important role. In this work, the effect of aphid colonization on three shrub species in urban environment was examined. Fourteen parameters have been analyzed, describing photosynthetic pigment content and gas exchange to carbon, nitrogen, and hydrogen partition. While no significant effect of colonization was found on photosynthetic pigment parameters, the effect was significant on gas exchange parameters. The strongest effect aphid colonization achieved on nitrogen partition and C/N ratio, parameters that could be suggested in further similar studies. All parameters were classified in two groups according to principal component analysis, suggesting correlation between nitrogen and carbon content, C/N ratio, measured gas exchange parameters and chlorophyll a content. The ratio between net photosynthesis and dark respiration (A/K) was in the second group, suggesting that this parameter provide additional information on the effect of aphid colonization, and deserve special attention in further studies. There were differences in reaction of examined shrub species, where the strongest reaction by gross primary productivity (GPP) achieved Hybiscus syriacus, and by nitrogen partition and C/N ratio Spirea trilobata and Cydonia japonica.

Beer fermentation is typically monitored by periodic sampling and off-line analysis. In-line sensors would remove the need for time-consuming manual operation and provide real-time evaluation of the fermenting media. This work uses a low-cost ultrasonic sensor combined with machine learning to predict the alcohol concentration during beer fermentation. The highest accuracy model (R2=0.952, MAE=0.265, MSE=0.136) used a transmission-based ultrasonic sensing technique along with the measured temperature. However, the second most accurate model (R2=0.948, MAE=0.283, MSE=0.146) used a reflection-based technique without the temperature. Both the reflection-based technique and the omission of the temperature data are novel to this research and demonstrate the potential for a non-invasive sensor to monitor beer fermentation.

The mass concentration of particulate matter (PM) has been systematically used in epidemiological studies as exposure indicator, to relate airborne concentrations with a wide variety of human health effects, which can be hardly explained by using this single parameter. In fact, PM is a “particle cocktail” that includes a complex mixture of compounds with a wide range of sizes, chemical compositions and emission sources. Current research hypothesizes that many of the adverse health effects are derived from oxidative stress in biological systems caused by the deposition of PM into the lungs. This emerging hypothesis is called the oxidative stress paradigm. In this commentary article we analize how this new paradigm could help to answer the as-of-yet unanswered questions related to the mechanism of action of PM pollution on human health. Acellular oxidative potential (OP) assays have been emerged as a promising approach to quantify the PM potential to induce oxidative stress and to relate it with the chemical composition and size distribution of PM. Recent researches have shown that the OP is related to the presence of metals, organic carbon, polyaromatic hydrocarbons and quinones. However, the association between PM and particle-induced toxicity is still largely unknown. Therefore, additional research is needed to identify the specific PM characteristic(s), such as its specific size, emission source or chemical content, which contribute the most to its redox activity. Thus, the OP measurements provide information that allows us to evaluate and integrate the toxic potential of PM in a unique parameter, whose relationships with emission sources, size distribution and/or chemical composition should be faced in the near future.

PVC-based materials are bad in terms of biodegradability. To enhance the ecological property of such materials, the fabrication of PVC-based composites using biofillers with acceptable performance characteristics could be considered. In this work, plant-filled PVC-based composite materials were obtained and study their optical, structural, thermal, and mechanical properties depending on the nature of the filler (spruce flour, birch flour, and rice husk) were studied. Increasing the proportion of plant filler somewhat reduces the strength characteristics and reduces the flexibility of the samples. But samples with plant filler allows them to be used at low temperatures without changing the operating characteristics. Some of the fillers affected the thermal stability of composites by increasing their thermal decomposition resistance. So, results have shown that plant-filled polymer composites based on PVC can be used on an equal basis with unfilled PVC plastic compound for some applications such as construction.

The service life of the reinforced concrete structure in the marine environment can be impaired significantly due to chloride-induced corrosion. However, how the chloride diffusion in pre-cracked concrete structures is affected by the hydrostatic pressure magnitude is poorly understood. This study experimentally examined the effect of hydrostatic pressure on the chloride diffusion in pre-cracked concrete. Cracks with five different widths, i.e., 20 μm, 40 μm, 60 μm, 80 μm, and 100 μm, were manually created using a splitting tensile apparatus respectively. The chloride diffusion in the concrete with a certain crack was then studied under four different hydrostatic pressures of 0 MPa, 0.1 MPa, 0.3 MPa, and 0.5 MPa. Experimental results show that the chloride diffusion in concrete with a crack greatly relies on both the hydrostatic pressure and the crack width. The chloride concentration increases as the hydrostatic pressure grows, particularly for the wider cracks with width ranging from 60 μm to 100 μm. Surprisingly, the hydrostatic pressure has a negligible effect on the chloride distribution in the concrete with a crack width no larger than 40 μm. Both the chloride diffusion coefficient and the surface chloride concentration of concrete increased gradually as the hydrostatic pressure increased. The experimental findings enrich our understanding of the behavior of pre-cracked concrete when exposed to chloride-induced corrosion at different depths of marine environments.

The paper presents a synthesis of deep eutectic solvents (DESs) based on choline chloride (ChCl) as hydrogen bond acceptor and phenol (Ph), glycol ethylene (EG), and levulinic acid (Lev) as hydrogen bond donors in 1:2 molar ratio. DESs were successfully used as absorption solvents for removal of dimethyl disulfide from (DMDS) from model biogas steam. Several parameters affecting the absorption capacity and absorption rate has been optimized including kind of DES, temperature, the volume of absorbent, model biogas flow rate, and initial concentration of DMDS. Furthermore, reusability and regeneration of DESs by means of adsorption and nitrogen barbotage followed by the mechanism of absorptive desulfurization by means of density functional theory (DFT) as well as FT-IR analysis were investigated. Experimental results indicate that the most promising DES for biogas purification is ChCl:Ph, due to high absorption capacity, relatively long absorption rate, and easy regeneration. The research on the absorption mechanism revealed that van der Waal interaction is the main driving force for DMDS removal from model biogas.

In order to assess the human exposure risks from the release of contaminants from water pipes made of polyvinyl chloride (PVC), experiments were carried out by subjecting the PVC pipe material to burning and leaching conditions followed by analysis of the emission and leachate samples. The emissions of burning pipes were analyzed by both infrared spectrometry and gas chromatography-mass spectrometry (GC-MS). The emission results indicate the presence of chlorinated components including chlorine dioxide, methyl chloride, methylene chloride, allyl chloride, vinyl chloride, ethyl chloride, 1-chlorobutane, tetrachloroethylene, chlorobenzene, and hydrogen chloride were detected in the emissions of burning PVC pipes. Furthermore, the concentrations of benzene, 1,3-butadiene, methyl methacrylate, carbon monoxide, acrolein, and formaldehyde were found at levels capable of affecting human health adversely. The analysis of PVC pipe leachates using GC-MS shows that there are 40-60 tentatively identified compounds, mostly long-chain hydrocarbons such as tetradecane, hexadecane, octadecane, and docosane, were released when the burned PVC materials were soaked in deionized water for one week. Quantitative analysis shows that 2-butoxyethanol, 2-ethyl-1-hexanol, and diethyl phthalate were found in the burned PVC polymer at the average levels of 2.7, 14.0, and 3.1 micrograms per gram (g/g) of pipe material. This study has significant implications for understanding the benzene contamination of drinking water in the aftermath of wildfires that burned polymer pipes in California.

Based on the previous work done by Fujii et al., NdBaInO4 compounds present modest oxide-ion conductivities. Therefore, it has been an attractive system of significant interest. In this paper, the Ca element has been attempted to partially substitute for Nd and the total electrical conductivity has been successfully improved due to the generation of oxygen vacancies. The synthesis, crystal structure, density, surface topography and electrical properties of NdBaInO4 and Ca-doped NdBaInO4 have been studied respectively. NdBaInO4, 10% and 20% molar fraction of Ca doped NdBaInO4 were synthesized through solid state reaction and they were calcined at 1000 °C for 14 hours and sintered at 1440 °C,1430 °C and 1420 °C respectively. The crystal structure of them has been obtained from Le Bail refinement of the XRD pattern, giving the result of the monoclinic structure which belongs to P21/c space group. The size of particles processed with different ball milling time and surface topography have been detected by the scanning electron microscope. The total electrical conductivities of Nd1-xCaxBaInO4-x/2 (x = 0, 0.1 and 0.2) were measured in the dry atmosphere by AC impedance spectroscopy and Nd0.9Ca0.1BaInO3.95 exhibited the highest total electrical conductivity and the lowest activation energy. What is more, the total conductivity of Nd0.9Ca0.1BaInO3.95 in the wet atmosphere at moderate temperature is relatively higher than that in the dry atmosphere while this phenomenon was not found in NdBaInO4. Therefore, the excess conductivity suggests that potential proton conduction may exist in wet atmospheres. In addition, Ca-doped NdBaInO4 were chosen for the oxygen isotope exchange which aims to obtain the diffusion coefficient and surface exchange coefficient, and Nd0.9Ca0.1BaInO3.95 shows the highest diffusion coefficient and D* decreases with the increase of the molar fraction of the Ca element.

Ion channels serve many cellular functions including ion homeostasis, volume regulation, signaling, nutrient acquisition, and developmental progression. Although the complex lifecycles of malaria parasites necessitate ion and solute flux across membranes, whole genome sequencing of the human pathogen, Plasmodium falciparum, revealed remarkably few orthologs of known ion channel genes. Contrasting with this, biochemical studies have implicated channel-mediated flux of ions and nutritive solutes across several membranes in infected erythrocytes. Here, I review advances in the cellular and molecular biology of ion channels in malaria parasites. These studies have implicated novel parasite genes in the formation of at least two ion channels, with additional ion channels likely present at various membranes and parasite stages. Computational approaches that rely on homology to known channel genes from higher organisms will not be very helpful in identifying the molecular determinants of these activities. Given their unusual properties, novel molecular and structural features, and essential roles in pathogen survival and development, parasite channels should be promising targets for therapy development.

To date, zinc ion batteries (ZIBs) have been attracting extensive attention due to their outstanding properties and the potential to be the solution for next-generation energy storage systems. However, the uncontrollable growth of zinc dendrites and water-splitting issues seriously restrict the further scalable application. Over the past few years, solid polymer electrolytes (SPEs) have been regarded as a promising alternative to address these challenges and facilitate the practical advancement of zinc batteries. In this review, we revisited the research progress of SPEs applied in zinc batteries in the past few years and focus on introducing cutting-edge polymer science and technologies that can be utilized to prepare advanced SPEs for high-performance zinc batteries. The operating mechanism of SPEs and the functions of polymers will be summarized. To highlight the polymer functions, SPEs are categorized into three types, respectively, homogenous polymer SPEs, hybrids polymer SPEs, and nanocomposites SPEs, which are expected to reveal the roles and principles of various polymers in zinc batteries. This review presents the current research progress and fundamental mechanisms of polymer-based SPEs in zinc batteries, outlines the challenging issues encountered, and meanwhile proposes potential solutions for future endeavours.

The generation and maintenance of membrane potential is a fundamental part of Membrane Pump Theory. One of the key points of this hypothesis is based on a natural or facilitated molecular diffusion through several types of ion channels and pumps like the Na/K ATPase. Following the principles of chemistry, electrostatics and geometry, it becomes clear that ion channels cannot function in this way. The ions channels cannot by their location have both a filter function and be ion concentrators, and the Na/K pump by its position in the membrane and by the proposed assumptions is not able to perform its regulatory function. The current model must absolutely be revised according to the current state of our knowledge and allow an advance in the understanding of the phenomena opening new research perspectives.

Ion channels contribute fundamental properties to all cell membranes. The ion channels are highly diverse in conductivity, structure, location and function. However, many of them can be regulated by common mechanisms, such as voltage or (de-)phosphorylation. Considering primarily pain-related ion channels, this review covers more novel and less known features of ion channel function, also with the aim to transfer knowledge between fields, which get inevitably more separate due to their size.

Magnetic nanoparticles are met across many biological species ranging from magnetosensitive bacteria, fishes, bees, bats, rats, birds, to humans. They can be both of biogenetic origin and due to environmental contamination, being either in paramagnetic or ferromagnetic state. The energy of such naturally occurring single-domain magnetic nanoparticles can reach up to 10-20 room k_BT in the magnetic field of the Earth, which naturally led to supposition that they can serve as sensory elements in various animals. This work explores within a stochastic modeling framework a fascinating hypothesis of magnetosensitive ion channels with magnetic nanoparticles serving as sensory elements, especially, how realistic it is given a highly dissipative viscoelastic interior of living cells and typical sizes of nanoparticles possibly involved.

The cell case temperature versus time profiles of a multistage fast charging technique (4C-1C-CV)/fast discharge (4C) in a 2.3 Ah cylindrical lithium-ion cell are analyzed using a 1D thermal model. Heat generation is dominated by the irreversible component associated to cell overpotential, although evidences of the reversible component are also observed, associated to the heat related to entropy from the electrode reactions. The final charging stages (i.e., 1C-CV) significantly reduce heat generation and cell temperature during charge, resulting in a thermally safe charging protocol. Cell heat capacity was determined from cell specific heats and cell materials thickness. The 1D model adjustment of the experimental data during the 2 min. resting period between discharge and charge allowed us to calculate both the time constant of the relaxation process and the cell thermal resistance. The obtained values of these thermal parameters used in the proposed model are almost equal to those found in the literature for the same cell model, which suggests that the proposed model is suitable for its implementation in thermal management systems.

Tomato is considered moderately sensitive to salinity, which detracts from the quality and yield of its fruit; therefore, wild populations have been used as a genetic resource. The aim of this research was to identify lines derived from wild tomato populations with tolerance to salinity during the germination and seedling stages. During germination, 52 wild lines and 2 commercial hybrids (Imperial®, Reserva®) were subjected to 150 mM and 0 mM NaCl and evaluated. The test was carried out for 20 days in a germination chamber with constant darkness, temperature of 25±2 °C and relative humidity of 80±4%. At the seedling stage, 22 wild tomato lines with the best performance in the germination test and 2 commercial hybrids (Imperial®, Topanga®) were evaluated for 12 days in a floating raft system. Concentrations of 175 mM and 0 mM NaCl were used. During germination, the saline condition decreased germination percentage (65.2%), speed of germination (88.2%), steam length (72.5%), root length (46.56%), normal plants number (59.5%), stem dry matter (68.78%), root dry matter (61.99%), and total dry matter (67.1%). At the seedling stage, this condition decreased (P<0.05) the aerial part dry matter (46.37%), leaf area (59.35%), root length (42.43%), final plant height (40.24%), and growth rate (71.42%). Seventeen tolerant genotypes were identified at one of both developmental stages, while one genotype showed tolerance at both stages. These results indicate that there are different response mechanisms in each developmental stage. Native tomatoes play an important role in the identification of tolerant genotypes since they can be used as genetic resources for obtaining commercial genotypes with salt tolerance.

The use of disinfectants, particularly those containing quaternary ammonium compounds (QUACs), has dramatically escalated globally since the coronavirus disease 2019 pandemic. We report a case that highlights the risks associated with the ingestion of a low-concentration QUACs solution and emphasizes the importance of effective management in resolving severe lesions without sequelae. A 17-month-old boy experienced severe respiratory failure after ingesting a disinfectant containing benzalkonium chloride (BAC). The child was initially treated in a local emergency department and was subsequently transferred to a pediatric poison center. Upon evaluation, the child was found to have grade III-A corrosive esophageal lesions and chemical pneumonitis. Several complications, including massive pneumothorax and candidemia, occurred during the clinical course of the disease. However, with timely medical intervention and appropriate supportive care, the patient completely recovered without any long-term sequelae. The properties of BAC and a comprehensive management approach may have been responsible for the patient's full recovery despite the potential life-threatening effects of the ingestion of disinfectants.

According to cancer death rates for women worldwide, this form of cancer ranks fourth after breast, bronchopulmonary, and colorectal cancer, affecting around 570,000 women annually. About 270,000 women each year pass away from this illness, 85% of them are from underdeveloped nations where cervical cancer claims more lives than any other kind of cancer. In Romania, cervical cancer ranks fourth in terms of death, behind breast, bronchopulmonary, and colorectal cancers, and second in terms of incidence, behind breast cancer. Endometriosis in the cervical region is quite uncommon. Only a tiny fraction of women had the condition upon diagnosis. It might be challenging to detect cervical endometriosis since it rarely manifests any symptoms or markers. Women who are asymptomatic can manage the condition expectantly; however, if the symptoms return often, surgery may be required. As many patients have concurrent diseases such fibroids, adenomyosis, ovarian cysts, and pelvic endometriosis, cervical endometriosis therapy appears to be straightforward. There ought to be surgical intervention. Symptomatic cervical endometriosis, such as irregular or post-coital bleeding, may be treated surgically using the LLETZ surgery or another cervical ablation approach. Background and Objectives: (1) To assess one's degree of knowledge on the signs, causes, and methods of preventing cervical cancer or cervical endometriosis, as well as screening for these conditions. (2) To ascertain how the responder behaves about cervical cancer screening and prevention, as well as endometriosis in the cervical region. Materials and Methods: A case report about cervical cancer or cervical endometriosis was conducted among a patient from Romania, Timisoara. Results: In this study, we report the patient with cervical endometriosis, although he was initially diagnosed with cervical cancer. Conclusions: Cervical cancer, a condition that can have serious repercussions on the patient's health, even if there is no clear picture of paraclinical investigations, to raise the suspicion of cervical endometriosis and not cervical cancer.

Spider silk has excellent strength and elasticity in natural, researchers have been working for decades try to achieve natural spider silk outstanding mechanical properties using recombinant spider silk protein (spidroin) through artificial spinning. In this work, we chose wet spinning method to explore the relationship between concentration of coagulation bath and fiber performance. It was found that the concentration of methanol has important effect on fiber continuity, diameter and mechanical properties. Lower concentration favors spinning continuous thinner, fibers with high strain. Secondary stretching benefits spinning silk fibers with stable mechanical properties, and thermal stability. Through applying different methanol concentration and additional stretching, we obtained silk fibers with Young’s modulus of 3.052± 2.626 GPa, stress of 25.3944 ± 17.48 MPa, and strain of 140 ± 95.4%.

The concentration of cerebrospinal fluid total protein (CSF-TP) is important for the diagnosis of neurological emergencies. Recently, some Western studies have shown that the current upper reference limit of CSF-TP is quite low for older patients. However, little is reported about the concentration of CSF-TP in older Asian population. In this study, we retrospectively analyzed the CSF-TP concentrations in Japanese healthy older volunteers. CSF samples in 69 healthy Japanese volunteers (age range: 55–73 years) were collected by lumbar puncture, and the data of CSF were retrospectively analyzed. The mean (standard deviation) CSF-TP was 41.7 (12.3) mg/dL. The older group (≥ 65 years old) had higher CSF-TP concentration than the younger group (55–64 years old). The 2.5th percentile and 97.5th percentile of CSF-TP were estimated as 22.5 and 73.2 mg/dL, respectively, which were higher than the current reference range in Japan (10–40 mg/dL).

MEMThe PdNi film hydrogen sensors with Wheatstone bridge structure were designed and fabricated by the micro-electro-mechanical system (MEMS) technology. The integrated sensors consisted of four PdNi alloy film resistors. The interval two of them were shielded with silicon nitride film and used as reference resistance, while the others were used for hydrogen sensing. The PdNi alloy films and SiN films were deposited by magnetron sputtering. The morphology and microstructure of the PdNi films were characterized with X-ray diffraction (XRD). The output resistance signal was converted to millivolt output voltage signal for easy data acquisition. Hydrogen (H2) sensing properties of PdNi film hydrogen sensor with Wheatstone bridge structure was investigated under different temperatures (30℃, 50℃ and 70℃) and H2 concentrations (from 10 ppm to 0.4%). The hydrogen sensor demonstrated good response at different hydrogen concentrations and high repeatability in cycle testing under 0.4% H2 concentration. Under 10ppm hydrogen, the PdNi film hydrogen sensor had evident and collectable output voltage of 600 μV.

The kinetics and efficacy profiles of photoinitiated polymerization are theoretically presented. For the same dose, lower light intensity achieves a higher steady-state-efficacy (SSE) in type-I; in contrast, type-II has an equal SSE. Higher light intensity has a faster rising efficacy, due to faster depletion of photoinitiator (PS) concentration. However, type-II process is also affected by the available oxygen. Higher light intensity produces more efficient singlet oxygen, resulting a higher transient efficacy, in which all intensities reach the same SSE when oxygen is completely depleted. With external oxygen, type-II efficacy increases with time, otherwise, it is governed only by the light dose, i.e., same dose achieves same efficacy. Moreover, type-II has an efficacy follows Bunsen Roscoe law (BRL), whereas type-I follows non-BRL. The measured type-I efficacy and gelation profile are analyzed by our analytic formulas. Schematics of the photocrosslinking stage defined by the availability of oxygen is developed, where both type-I and –II coexist until the oxygen is depleted. The overall efficacy may be enhanced by resupply of PS or oxygen during the light exposure. The roles of light dose and PS concentration on the efficacy of photoinitiated polymerization should be are governed a new concept of a volume efficacy (Ve), defined by the product of the crosslink (or gelation) depth (CD) and local [efficacy].

The present research intents to study the evolution of the skin fatty acids and physiological disorders through cold storage in ‘Golden Delicious’ apples treated with 1-MCP and calcium. Harvested fruit were treated with calcium chloride (Ca), 1-MCP (MCP), Ca+MCP or no treatment (control) then subjected to cold storage at 0.5 ºC for 6 months. Fatty acids composition, Malondialdehyde (MDA) and the physiological disorders bitter pit (BP), superficial scald and diffuse skin browning (DSB) were measured at harvest and after storage plus 7 days shelf-life at room temperature ≈22 ºC. Palmitic acid decreased and linoleic acid increased through time, while oleic and stearic acids had few changes. Unsaturated/saturated fatty acids and MDA increased through time, despite Ca and Ca+MCP were related to lower MDA and lower BP and rotten fruit, after cold storage and shelf-life. In those treatments, the unsaturated/saturated fatty acids were higher, mainly due to higher linoleic acid and lower palmitic acids. Further research is needed to clarify the changes in membrane properties and the effect of some treatments in response to chilling injury through storage.

A novel prediction model for crack development of reinforced concrete (RC) piles with localized chloride corrosion in marine environment is proposed. A discrete method is used to solve the corrosion pit radius model and a crack extension model is developed to investigate the initiation and extension of cracks. The maximum corrosion degree of reinforced concrete pile is predicted according to the limit crack criterion, and finally a sensitivity analysis is carried out on the important parameters of crack extension. The results show that the radius of corrosion pit, the depth corrosion pit and cross-sectional area loss of reinforcement gradually increase as the corrosion level increases. The loss of local reinforcement section at crack initiation decreases with the increase of the ratio of concrete cover to initial diameter, and increases with the increase of pitting factor. The required pit depth for reinforcement cracking increases with the increase of the ratio of concrete cover thickness to diameter. The loss of cross-sectional area of reinforcement and the radius of corrosion pit increase with the increase of initial diameter of reinforcement. Increasing the pitting factor will reduce the pit depth and make the crack width develop faster before reaching the limit crack width. Increasing the concrete cover thickness can provide an improvement in the propagation of cracks. A comparative analysis shows that the localized corrosion pattern is more in conformity with marine engineering practice.

Molten salt reactors have gained substantial interest in the last years due to their flexibility and their potential for simplified closed fuel cycle operation for massive net-zero energy production. However, a zero-power reactor experiment will be an essential first step into the process of delivering this technology. The topic of the control and shut down for a zero power reactor is for the first time introduced through a literature review and the reduction of the control approaches to a limited number of basic functions with different variations. In the following, the requirements for the control and shutdown system for a reactor experiment are formulated, and based on these assessments, an approach for the shutdown – splitting the lower part of the core with reflector, and an approach for the control – a vertically movable radial reflector are proposed. Both systems will be usable for a zero-power system with a liquid as well as with as a solid core and even more importantly, both systems somehow work on the integral system level without disturbing the central part of the core which will be the essential area for the experimental measurements. Both approaches have been investigated as a singular system as well as their interactions with one another and the sensitivity of the control system. The study has demonstrated that both proposed systems are able to deliver the required characteristics with sufficient shutdown margin and a sufficiently wide control span. The interaction of the system has been shown to be manageable and the sensitivity is on a very good level. The multi-group Monte-Carlo approach has been cross evaluated by a continuous energy test leading to good results, but they also demonstrate that there is room for improvement.

Water quality monitoring was an important objective in the surroundings. In this study, we investigated the sensing characteristics of the arrayed flexible chloride sensor with XBee wireless sensing system. The sensitivity and linearity of the wireless chloride sensing devices were 91.6 mV/pCl and 0.988, respectively. The hysteresis voltages were 50.14 mV and 36.71 mV during the cycles of 1 M → 10⁻¹ M → 1 M → 10⁻³ M → 1 M and 1 M → 10⁻³ M → 1 M → 10⁻¹ M → 1 M, respectively. The selectivity coefficients of the ClO⁻ ion, ClO₄⁻ ion, NO₃⁻ ion and I⁻ ion for Cl⁻ ion were 5.0 × 10⁻², 1.0 × 10⁻¹, 5.9 × 10⁻³ and 5.6×10⁻¹, respectively. The sensing characteristics of real time measurement were investigated for dynamic microfluidic. The arrayed flexible chloride sensor was integrated with the microfluidic device, syringe pump and wireless sensing system. The sensitivity and linearity were 273.1 mV/pCl and 0.978 at 35 μL/min, respectively.