Lettuce is a salt-sensitive crop and has a threshold electrical conductivity of 1.3–2.0 mS cm-1 and above that is considered detrimental. As there has been very little information on the physio-logical response of different critical stages of lettuce under different salt stress (SS), the current study is focused on investigating the effects of SS on the critical physiological traits influencing the carbon assimilation in different growth stages of lettuce. The experiment was conducted in deep-water culture hydroponic system in a greenhouse condition. Four levels of sodium chloride salt treatments (EC: 20, 16, 8, and 1.8 mS cm-1) were applied. During both growth stages (day 11 (GS1) and day 19 (GS2) after salt treatment), the leaf transpiration rate, stomatal conductance, and intercellular CO2 were severely decreased. However, the carbon assimilation rate remained unchanged under SS. Similarly, the water use efficiency increased under the SS. It is concluded that the increasing SS increased stomatal and non-stomatal limiting factors during GS1 suggesting the enhanced limitation in photosynthetic activity while no such trend was observed during GS2. The decreased gm with increased SS at GS1 and GS2 suggested that SS induced the irreversible decrease of gm, which in turn can be responsible for the transient reduction in the Vcmax and Jmax during GS2. Taken together, the evidence from this research recommends that varying the SS levels can significantly affect the physiological performance of lettuce at both growth stages.

The Total Algae Peak Integration Retrieval TAPIR relates the chlorophyll-a absorption coefficient at 440 nm (a440) to the reflectance peak near 683 nm induced by chlorophyll-a properties. The two-step retrieval provides both the hyperspectral quantification of the phytoplankton fluorescence and scattering and the estimation of a440 from reflectance signals. Integrating the peak, the Total Algae Peak (TAP) accounts for the variance in the peak's magnitude, shape, and central peak wavelength. TAPIR is a solely optical approach estimating a440 and supports the application of retrieval-independent individual regional bio-optical models afterwards to retrieve the chlorophyll-a concentration. Simulations reveal the major sensitivity on the considered model chlorophyll-a absorption spectrum and its single scattering albedo. Additional water and atmosphere constituents have a low impact. An uncertainty assessment reveals uncertainties of less than 30% for TAPIR a440 greater than 0.8 m-1 and less than 38% for lower a440. In optically complex waters, first validation efforts promise the applicability of TAPIR for high chlorophyll-a concentration estimations in the presence of additional water constituents. The technique is generic and considers external conditions (sun zenith angle, number of measurement bands, surface or satellite measurements, and radiometric quantity). TAPIR applies to all kind of waters including optically complex waters, arctic to tropical regions, and inland, coastal, and open ocean waters. Among other hyperspectral satellite sensors, the Environmental Mapping and Analysis Program (EnMAP) provides sufficient sampling bands for the application of TAPIR.

Photosynthesis is one the most important biological processes on earth, producing life-giving oxygen and is the basis for a large variety of plant products. Measurable properties of photosynthesis provide information about its biophysical state and, in turn, the physiological conditions of a photoautotrophic organism. For instance, chlorophyll fluorescence of an intact photosystem is not linear as in the case of a single fluorescent dye in solution, but shows temporal changes related to the quantum yield of the photosystem. Commercial photosystem analyzers already use the fluorescence kinetics characteristics of photosystems to infer the viability of organisms under investigation. Here, we provide a novel approach based on an optical Fabry-Pérot microcavity or that enables the readout of photosynthetic properties and activity for an individual cyanobacterium. This approach offers a completely new dimension of information, which would normally be lost due to averaging in ensemble measurements obtained from a large population of bacteria.

Tissue-like phantoms are widely used as a model for mimicking the optical properties of live tissue. This paper presents the results of a diffusion reflection method as well as fluorescence lifetime imaging microscopy measurements of fluorescein-conjugated gold nanorods in solution as well as inserted in solid tissue-imitating phantoms. A lack of consistency between the fluorescence lifetime results of the solutions and the phantoms raises a question about the ability of tissue-like phantoms to maintain the optical properties of inserted contrast agents.

Biomimetic materials are substances that replicate natural structures. There are several methods for producing such materials with highly developed surfaces from a wide range of polymers, but electrospinning is of particular interest due to its simplicity of implementation and the ability to modify the produced fibrous materials resembling structures found in living organisms. This study explores new biomimetic materials based on polyhydroxyalkanoates, specifically poly-3-hydroxybutyrate, modified with chlorophyll derivatives. The research investigates the impact of chlorophyll derivatives on the morphology, supramolecular structure, and key properties of nonwoven materials. The obtained results are of interest for the development of new biomimetic environmentally friendly materials for biomedicine with special properties.

The retrieval of sun-induced chlorophyll fluorescence is greatly beneficial to studies of marine phytoplankton biomass, physiology, and composition and is required for user applications and services. Customarily phytoplankton chlorophyll fluorescence is determined from satellite measurements through a fluorescence line-height algorithm using three bands around 680 nm. We propose here a modified retrieval, making use of all available bands in the relevant wavelength range with the goal to improve the effectiveness of the algorithm in optically complex waters. For the Ocean and Land Colour Instrument (OLCI) we quantify a Fluorescence Peak Height from fitting a Gaussian function and related terms into the top-of-atmosphere reflectance bands between 650 and 750 nm. This algorithm retrieves, what we call Fluorescence Peak Height from fitting a Gaussian function upon other terms to top-of-atmosphere reflectance bands between 650 and 750 nm. This approach is applicable to Level-1 and Level-2 data. We find a good correlation of the retrieved fluorescence product to global in-situ chlorophyll measurements, as well as a consistent relation between chlorophyll concentration and fluorescence from radiative transfer modelling and OLCI/in-situ comparison. The algorithm is applicable to complex waters without needing an atmospheric correction and vicarious calibration and features an inherent correction of small spectral shifts, as required for OLCI measurements.

Validation of the TROPOspheric Monitoring Instrument (TROPOMI) SIF product is a necessity to evaluate its feasibility in various applications. A few validation works have been conducted through direct comparison with in-situ SIF retrievals or cross-comparison with similar satel-lite-based SIF or vegetation index (VI) products. Nevertheless, the influence of the geolocation mismatch between the validation pixel and reference data on validation results was never con-sidered. This study, for the first time, quantifies the geolocation shift of the TROPOMI validation pixel based on a geometric location matching method and then the uncertainty caused by the ge-olocation mismatch. The results indicate that the geolocation shift of the TROPOMI pixel shows large temporal variations, with a standard deviation of 2.45 km and 1.96 km in the across- and along-track directions. The mean shifts are 0.07 km and 0.25 km in the across- and along-track directions respectively, indicating eastward shifts in the across-track direction and northward shifts in the along-track direction in general. More than half (42/54) of the time periods showed relative uncertainty larger than 5%, with the maximum even reaching 55.7%. Hence, the uncertainty caused by geolocation mismatch should be fully considered in the validation of satellite SIF products, especially over heterogeneous surfaces.

Within the spectra of lanthanide atoms quite often overlapping spectral lines (blends) are observed. On the example of complicated blend situations within Pr I and La I it is shown that in such cases a combination of optogalvanic and laser-induced fluorescence detection is necessary to find all transitions contributing to the observed spectral signature.

In an attempt to correct misunderstandings this article brings together the observations on Calcium, Myosin Binding Protein-C and Hypertrophic Cardiomyopathy in the basic function of cardiac muscle. A finding of many years ago is reiterated in a novel enzyme kinetic format with defined rate limiting step which makes CaATP the apparent substrate of the actomyosin cross-bridge. The relationship of these kinetics to recent observations on disruption of myosin binding protein-C is described along with how this bears on the understanding of the related cardiomyopathies.

The α-glucosidase inhibitor is of interest to researchers due to its association with type-II diabetes treatment by suppressing postprandial hyperglycemia. Hesperidin is a major flavonoid in orange fruit with diverse biological properties. This paper evaluates the effects of hesperidin on α-glucosidase through inhibitory kinetics, fluorescence quenching, and molecular docking methods for the first time. The inhibition kinetic analysis showed that hesperidin reversibly inhibited the α-glucosidase activity with an IC50 value of 18.52 M and the inhibition was performed in an uncompetitive type. Fluorescence quenching studies indicated that the intrinsic fluorescence of α-glucosidase was quenched via a static quenching process and only one binding site was present between hesperidin and α-glucosidase. The interaction between them was spontaneous and mainly driven by hydrogen bonds as well as hydrophobic forces. Furthermore, molecular docking results suggested that hesperidin might bond to the entrance or outlet part of the active site of α-glucosidase through a network of five hydrogen bonds formed between hesperidin and the four amino acid residues (Trp709, Arg422, Asn424, and Arg467) of ?-glucosidase and hydrophobic effects. These results provide new insights into the inhibitory mechanisms of hesperidin on α-glucosidase, supporting the potential application of hesperidin-rich orange product as a hypoglycemic functional food.

Deep Learning is a recent and important addition to the computational toolbox available for image reconstruction in fluorescence microscopy. We review state-of-the-art applications such as image restoration, super-resolution, and light-field imaging, and discuss how the latest Deep Learning research can be applied to other image reconstruction tasks such as structured illumination, spectral deconvolution, and sample stabilisation. Despite its successes, Deep Learning also poses significant challenges, has often misunderstood capabilities, and overlooked limits. We will address key questions, such as: What are the challenges in obtaining training data? Can we discover structures not present in the training data? And, what is the danger of inferring unsubstantiated image details?

Using UAV-based multispectral images for quickly and accurately monitoring chlorophyll content is critical for field management and yield estimation. However, the lower model accuracy and the poor robustness of the estimation models are still preventing the widespread application of UAV-based multispectral images. We carried out two field trials at various experimental sites to further enhance the precision and applicability of the model used to estimate the chlorophyll content of potato plants. Firstly, the texture features and vegetation indices derived from multispectral images were screened using the Pearson correlation coefficient method, and Normalized difference red edge (NDRE) performed the best over the two growth periods. Secondly, principal component analysis (PCA) was applied to recombine five bands of multispectral images, and third PCA results (PCA3) was selected to combined with NDRE according to the construction principle of NDRE, and the newly constructed parameter was named improved NDRE (INDRE). Finally, INDRE was used to establish a chlorophyll content estimation model of potato plants, and compared with some traditional parameters. The results demonstrated that the INDRE had the maximum accuracy (R2 = 0.7865, RMSE = 2.1378), and corresponding R2 increased by 0.1481 and RMSE decreased by 1.2994 than NDRE. Additionally, the model was validated using independent data from Experiment 2, and INDRE considerably increased estimation accuracy compared to other factors. In conclusions, the INDRE suggested in this study significantly enhances the accuracy and applicability of the chlorophyll content inversion model and can serve as an additional reference for fertilization management.

The concentration of chlorophyll-a (chlor-a) is an important indicator of marine water quality, as it is considered an indicator of the phytoplankton density in a specific area. Remote sensing techniques have been developed to measure the near-surface concentration of chlor-a in water across the correlation between spectral bands and in situ data. This algorithm applies to sensors of varying spatial, temporal and spectral resolutions. However, in this study, chlor-a level 2 and 3 products of SNPP – VIIRS spectrometer (Equation OC3) of NASA OceanColor suite was relied upon to study the spatial and temporal distribution of chlor-a concentration in the Arabian Gulf (also known as the Persian Gulf) and the State of Kuwait’s water (located to the north-eastern part of the Arabian Gulf) from 2012 to 2019. Ground truthing points (n = 192) matched to the level 2 products have been used to build an empirical model and cross-validate it. The correlation was positive where was 0.79 and the validation RMSE was = ± 0.64 mg/m^-3. The derived algorithm was then applied to chlor-a level 3 seasonal products. Additionally, the chlor-a concentration values of Kuwaiti waters have been enhanced using the IDW algorithm to increase the spatial resolution, as it is considered as a small area compared to the spatial resolution of level 3 chlor-a products. The model derived from IDW was tested using the Mann Whitney test (Sig = 0.948 p > 0.01). However, the result showed that the chlor-a concentration is higher in Kuwait Bay compared to Kuwaiti water, and it is higher in Kuwaiti water compared to the Arabian Gulf. The coasts have higher concentrations too, when compared to the open water. Generally, the chlor-a increases in winter and makes a semi-regular cycle during the years of study; this cycle is more regular in the Gulf’s waters than in Kuwait’s.

Eutrophication, a global concern, impacts water quality, ecosystems, and human health. It’s crucial to monitor algal blooms in freshwater reservoirs, as they indicate the trophic condition of a waterbody through Chlorophyll-a (Chla) concentration. Traditional monitoring methods, however, are expen-sive and time-consuming. Addressing this hindrance, we developed models using remotely sensed data from the Sentinel-2 satellite for large-scale coverage, including its bands and spectral indexes, to estimate the Chla concentration on 149 freshwater reservoirs in Ceará, Brazil. Several machine learning models were trained and tested, including k-nearest neighbours, random forests, extreme gradient boosting, the least absolute shrinkage, group method of data handling (GMDH), and sup-port vector machine models. A stepwise approach determined the best subset of input parameters. Using a 70/30 split for the training and testing datasets, the best-performing model was the GMDH, achieving an R2 of 0.91, MAPE of 102.34%, and RMSE of 20.38 g/L, which are values consistent with the ones found in the literature. Nevertheless, the predicted Chla concentration values were most sensitive to the red, green, and near infra-red bands.

In the present study, the effect of melatonin and sodium nitroprusside treatments on the improvement of high temperature tolerance in California Wonder green bell pepper plant was studied. For this purpose, a factorial experiment was conducted in form of a completely randomized design in three replications at Zabol University's Faculty of Agriculture. In this research, green bell pepper plants of Wonder cultivar were exposed to different temperature treatments (25°C, 35°C and 40°C) for 24 hours after being sprayed (foliar application) with 0μM, 50μM and 100μM concentrations of melatonin and Sodium nitroprusside. Results showed that Instantaneous leaf water consumption efficiency in 40°C temperature treatment with 50μM and 100μM melatonin increased. Also in 40°C temperature with 100µM melatonin, fruit dry weight in compared to control (0uM) 13.15% increased. Also, melatonin and sodium nitroprusside treatments in compared to control treatment improved fruit characteristics and reduced Appearance Characteristics of Fruit Marketability (ACFM) number. Under 40°C temperature treatment in compared to control temperature (25°C), fruit total soluble solids (TSS) 18.50% decreased also under 100μM melatonin treatment, fruit TSS 20.69% was increased compared to control treatment (0μM). Also fruit fructose at 40°C temperature in compared to 25°C temperature treatment 5.52% reduced. Fruit calcium at 35°C and 40°C temperature in compared to control temperature 6.96% and 15.65% decreased respectively. At temperature 35°C under foliar application of 100uM sodium nitroprusside, fruit copper in compared to control 28.93% increased.

The objective of this study was to investigate the impact of athletes' respiratory muscle strength, as assessed through maximal inspiratory (MIP) and expiratory pressure (MEP), on aerobic endurance, as indicated by maximal oxygen consump-tion (Max VO2) kinetics. Respiratory muscle strength was assessed using a digital spirometer (Pony FX Cosmed, Italy), while maximal oxygen utilization capacity was measured using a breath-by-breath automatic portable gas analysis system (Cosmed K5, Italy). Statistical analysis was conducted utilizing SPSS 22.0. Based on the standardized regression coefficients (β), it was found that MEP (mean ± SD: 130.95 ± 42.82) and inspiratory diaphragmatic circumference values significantly influenced ventilatory equivalent (VE), oxygen consumption (VO2), and carbon dioxide pro-duction (VCO2). Conversely, the remaining predictor variables did not exhibit a sig-nificant effect on VE (mean ± SD: 134.80 ± 36.69), VO2 (mean ± SD: 3877.52 ± 868.47 ml), and VCO2 (mean ± SD: 4301.27 ± 1001.07 ml). In contrast, measurements of chest circumference (mean ± SD: 91.40 ± 10.72 cm), MEP, and diaphragmatic cir-cumference during inspiration (mean ± SD: 95.20 ± 10.21 cm) were found to signifi-cantly impact Max VO2 (mean ± SD: 58.52 ± 10.74 ml/kg/min), while the other pre-dictor variables did not demonstrate a significant effect on Max VO2. Conclusively, the study revealed that measured values of diaphragmatic circumference during inspiration and MEP exerted a notable influence on Max VO2, VE, VO2, and VCO2. Our findings underscore the importance of considering respiratory muscle strength in assessing and enhancing athletes' aerobic performance. These insights contribute to a deeper understanding of the interplay between respiratory function and exercise capacity, offering potential avenues for optimizing training regimens and perfor-mance outcomes in athletic contexts.

Dormancy is a physiological state that confers winter hardiness to and orchestrates phenological phase progression in temperate perennial plants. Weather fluctuations caused by climate change increasingly disturb dormancy onset and release in many plant species including tree crops leading to aberrant growth, flowering, and fruiting. Currently, research in this field is impeded by the lack of affordable non-invasive methods for on-line monitoring of dormancy. We report on an automatic framework for low-cost, long-term, and scalable dormancy studies in deciduous plants. The proposed method is based on continuous near-field sensing of the photosynthetic activity of shoots via pulse-amplitude modulated chlorophyll fluorescence sensors connected remotely to a data processing system. The resulting high-resolution time series of JIP-test parameters indicative of the responsiveness of the photosynthetic apparatus to environmental stimuli are subjected to frequency-domain analysis. The proposed approach allows to overcome the variance coming from diurnal changes of insolation and to derive estimations on the depth of dormancy. Our approach was validated over three seasons in an experimental apple (Malus × domestica Borkh.) orchard by collating the non-invasive estimations with the results of traditional methods (growing of the cuttings obtained from the tress at different phases of dormancy) and the output of commonly used chilling requirement models. We discuss the advantages of the proposed monitoring framework such as prompt detection of freeze damages along with its potential limitations.

Laser-induced fluorescence spectroscopy (LIFS) is actively used for remote sensing of atmospheric aerosols and currently is one of the most sensitive and selective techniques for determining small concentrations of substances inside particles. The use of high-power femtosecond laser sources for LIFS-based remote sensing of aerosol contributes to the development of new-generation fluorescence atmospheric lidars since it makes it possible overcoming the energy threshold for the nonlinear-optical effects of multiphoton absorption in particles and receiving the emission signal at long distances in the atmosphere. Our study is aimed to the development and experimental demonstration the technique of nonlinear laser-induced fluorescence spectroscopy (NLIFS) based on the remote excitation of aerosol fluorescent emission stimulated by a spatially-structured high-power femtosecond laser pulse. Importantly, for the first time to our knowledge, we demonstrate the advances of using stochastically-structured plasma-free intense light channels (postfilaments) specially formed by propagation of femtosecond laser radiation through a turbulent air layer for improving NLIFS efficiency. A multiple increase in the received signal of two-photon-excited fluorescence of polydisperse dyed aqueous aerosol by the structured postfilaments is reported.

1) Landsat operational land imager (OLI) data and consequent laboratory measurements were used to predict Chlorophyll-a (Chl-a) concentration and the trophic states for an inland lake within the East Kolkata Wetland, India; 2) The most suitable band ratio was identified by performing Pearson correlation analysis between Chl-a concentrations and possible OLI band and band ratios from the study points; 3) The results showed highest correlation coefficient from the band ratio OLI5/OLI4 with an R value of 0.85. The prediction model was then developed by applying regression analysis between the band ratio OLI5/OLI4 and Chl-a concentration of the study points. The reflectance ratios of the validation points were given as input on the prediction model and the model output was considered as predicted Chl-a values of the validation points to check the efficiency of the prediction model. The regression model between laboratory-derived Chl-a value and model-fitted Chl-a value of the validation points revealed a high correlation with an R² value of 0.78. Trophic State Index (TSI) of the lake was also calculated from laboratory-derived Chl-a value and model-fitted Chl-a value of the validation points. The study presented a high correlation of TSI determined from predicted data with TSI from laboratory reference data (R = 0.88). The TSI values of the lake ranged from 65 to 75 which indicate that the lake is appeared to be eutrophic to hypereutrophic conditions. 4) This empirical study showed that Landsat 8 OLI imagery can be effectively applied to estimate Chl-a levels and trophic states for inland lakes.

This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

Turner syndrome (TS) is caused by a complete or partial absence of an X or Y chromosome, including chromosomal mosaicism, affecting 1 in 2,500 female live births. Sister chromatid exchange (SCE) is used as a sensitive indicator of spontaneous chromosome instability. Cells from mosaic patients constitute useful material for SCE evaluations as they grow under the influence of the same genetic background and endogenous and exogenous factors. We evaluated proliferation dynamics and SCE frequencies of 45,X and 46,XN cells of 17 mosaic TS patients. In two participants, 45,X cells exhibited a proliferative disadvantage in relation to 46,XN cells after 72h of cultivation. The analysis of mean PI showed significant differences between 45,X and 46,XN lineages; however there were no intraindividual differences. On the other hand, mean SCE frequencies showed no differences between the two lineages, but there were intraindividual differences in 5 patients. The absence of mean SCE frequency differences between 45,X and 46,XN lineages may indicate that both were equally unstable, as more than 70% of the 46,XN lineages had an anomalous karyotype. However, 46,XN had a higher mean PI, suggesting that the amount of cells with a karyotype distinct from 45,X may increase with time in mosaic TS women.

Amid global energy challenges, hydrogen evolution reaction (HER) is gaining traction for green hydrogen production. While catalyst research is ongoing, recognizing electrolyte effects remains crucial for sustainable hydrogen production via renewable-powered water electrolysis. This review delves into the intricate effects of electrolytes on the kinetics of HER. It examines key factors, including pH, cations, anions, impurities, and electrolyte concentration. It is discussed that electrolyte pH alters catalyst-electrolyte interactions and proton concentrations, thereby influencing factors such as hydrogen binding energy, water adsorption, and the overall reaction kinetics. Moreover, it is briefed that electrolyte cations, such as Li+, can impact HER positively or negatively, offering opportunities for improvement based on the metal substrate. Interestingly, there is a potential that HER can be tuned using Li+ ions to modify M-H bond energy, demonstrating flexibility beyond pH levels and counter ions. Varied adsorption energies of metal cations on metal electrodes are also found to influence HER kinetics. The effects of electrolyte anions and impurities are also discussed, emphasizing both positive and negative impacts on HER kinetics. Moreover, it is pointed out that the electrolyte engineering approach enhances the HER kinetics of both metal and carbon-based electrodes without permanent catalyst surface modifications. This review underscores the importance of electrolyte composition, highlighting both challenges and potential solutions in advancing HER research for sustainable energy production.

Epistemological naturalism dismisses the notion that epistemology is a basis for the empirical sciences. In particular, it rejects the demand for a general justification of induction. Making inductive generalisations is a basic habit among humans. There is no such thing as a logic of inductive inference. The role of induction in science is heuristic; it is our way of inventing new theoretical predicates and developing theories. We discover new laws by applying inductive thinking; but this is not any kind of inference which can be evaluated as more or less rational.

This study aimed to evaluate the impact of Candida albicans on subgingival biofilm formation on dental implant surfaces. Scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) were used to compare biofilm structure and microbial biomass in the presence and absence of the fungus after periods of 24, 48, and 72 h. Quantitative polymerase chain reaction (qPCR) was used to quantify the number of viable and total micro-organisms for each of the biofilm-forming strains. A general linear model was applied to compare CLSM and qPCR results between control and test conditions. The biofilm developed with C. albicans at 72 h had a higher bacterial biomass, with a significantly higher cell viability (p < 0.05). After both 48 and 72 h of incubation, in the presence of C. albicans, there was a significant increase in counts of Fusobacterium nucleatum and Porphyromonas gingivalis and in the cell viability of Streptococcus oralis, Aggregatibacter actinomycetemcomitans, F. nucleatum, and P. gingivalis. Using a dynamic in vitro multispecies biofilm model, C. albicans exacerbated the development of the biofilm grown on dental implant surfaces, significantly increasing the number and cell viability of periodontal bacteria.

As the coronavirus disease 2019 (COVID-19), which is caused by the novel SARS-CoV-2, continues to spread rapidly around the world, there is a need for well validated serological assays that allow the detection of viral specific antibody responses in COVID-19 patients or recovered individuals. In this study, we established and used multiple indirect Enzyme Linked Immunosorbent Assay (ELISA)-based serological assays to study the antibody response in COVID-19 patients. In order to validate the assays we determined the cut off values, sensitivity and specificity of the assays using sera collected from pre-pandemic healthy controls, COVID-19 patients at different time points after disease-onset, and seropositive sera to other human coronaviruses. The developed SARS-CoV-2 S1 subunit of the spike glycoprotein and nucleocapsid (N)-based ELISAs not only showed high specificity and sensitivity but also did not show any cross-reactivity with other CoVs. We also show that all RT-PCR confirmed COVID-19 patients tested in our study developed both virus specific IgM and IgG antibodies as early as week one after disease onset. Our data also suggest that the inclusion of both S1 and N in serological testing would capture as many potential SARS-CoV-2 positive cases as possible than using any of them alone. This is specifically important for tracing contacts and cases and conducting large-scale epidemiological studies to understand the true extent of virus spread in populations.

The massive amount of human biological, imaging and clinical data produced by multiple and diverse sources, necessitates integrative modeling approaches able to summarize all this information into answers to specific clinical questions. In this paper, we present a hypermodeling scheme able to combine models of diverse cancer aspects regardless of their underlying method or scale. Describing tissue-scale cancer cell proliferation, biomechanical tumor growth, nutrient transport, genomic-scale aberrant cancer cell metabolism, and cell signaling pathways that regulate the cellular response to therapy, the hypermodel integrates mutation, miRNA expression, imaging, and clinical data. The constituting hypomodels as well as their orchestration and links are described. Two specific cancer types, Wilms tumor (nephroblastoma) and non-small cell lung cancer, are addressed as proof of concept study cases. Personalized simulations over the actual anatomy of a patient have been carried out. The hypermodel has also applied to predict tumor control after radiotherapy and the relationship between tumor proliferative activity and response to neoadjuvant chemotherapy. Our innovative hypermodel holds promise as a digital twin based clinical decision support system and the core of future in silico trial platforms, although additional retrospective adaptation and validation is necessary.

In the context of the COVID-19 epidemic, and on the basis of the Theory of Dynamical Systems, we propose a simple model for the expansion of contagious diseases, with a particular focus on viral respiratory tracts. The infection develops through contacts between contagious and exposed people, with a rate proportional to contact duration and turnover, inversely proportional to the efficiency of protection measures, and balanced by the average immunological response. The obvious initial exponential increase is readily hindered by the size reduction of the exposed population. The system converges towards a stable attractor whose value is expressed in terms of the ratio C/D of contamination vs decay factors. Decreasing this ratio below a critical value leads to a tipping point beyond which the epidemic is over. By contrast, significant values of C/D may bring the system through a bifurcating hierarchy of stable cycles up to a chaotic behaviour.

Characterization of cancer cells and neural stem cells indicates that tumorigenicity and pluripotency are coupled cell properties determined by neural stemness, and tumorigenesis represents a process of progressive loss of original cell identity and gain of neural stemness. This reminds of a most fundamental process required for the development of the nervous system and body axis during embryogenesis, i.e., embryonic neural induction. Neural induction is that, in response to extracellular signals that are secreted by the Spemann-Mangold organizer in amphibians or the node in mammals and inhibit epidermal fate in ectoderm, the ectodermal cells lose their epidermal fate and assume the neural default fate and consequently, turn into neuroectodermal cells. They further differentiate into the nervous system and also some non-neural cells via interaction with adjacent tissues. Failure in neural induction leads to failure of embryogenesis, and ectopic neural induction due to ectopic organizer or node activity or activation of embryonic neural genes causes a formation of secondary body axis or a conjoined twin. During tumorigenesis, cells progressively lose their original cell identity and gain of neural stemness, and consequently, gain of tumorigenicity and pluripotency, due to various intra-/extracellular insults in cells of a postnatal animal. Tumorigenic cells can be induced to differentiation into normal cells and integrate into normal embryonic development within an embryo. However, they form tumors and cannot integrate into animal tissues/organs in a postnatal animal because of lack of embryonic inducing signals. Combination of studies of developmental and cancer biology indicates that neural induction drives embryogenesis in gastrulating embryos but a similar process drives tumorigenesis in a postnatal animal. Tumorigenicity is the manifestation of aberrant occurrence of pluripotent state in a postnatal animal. Pluripotency and tumorigenicity are both but different manifestations of neural stemness in pre- and postnatal stage, respectively, of animal life. The unique property of neural stemness is derived from the evolutionary advantage of neural genes and the neural-biased state of the last common unicellular ancestors of metazoan. Based on these findings, I discuss about some confusion in cancer research, propose to distinguish the causality and associations and discriminate causal and supporting factors involved in tumorigenesis, and suggest revisiting the focus of cancer research.

The alcoholic fermentation process with agitation/static, followed by the acetic fermentation submerged in banana was evaluated. Kinetics parameters of alcoholic fermentation for the maximum ethanol/glycerol metabolites in agitated process was 29 and 27 h, and in static 47 and 45 h, respectively. For acetic fermentation, the kinetics parameters were medium time of 39.9 h, acetic acid yield of 53.1% and acetic acid productivity of 0.216 g/Lh. Wines from agitated/static process presented 5.73 and 6.81% (v/v) of alcohol content, respectively. Wine obtained by the static process presented higher concentrations of volatile compounds. The vinegar showed 49.2 g/L of acetic acid and the esters concentrations were higher than in wine. The wine and vinegar minerals were consistent with amount observed in the pulp, with an increase in sulphur concentration after alcoholic fermentation and decrease after acetic fermentation. Products showed chemical and composition of sensory and nutritional interest.

Despite the successful introduction of oral cholera vaccines, Zambia continues to experience multiple, sporadic, and protracted cholera outbreaks in various parts of the country. While vaccines have been useful in staying the cholera outbreaks, the ideal window for re-vaccinating individual’s resident in cholera hotspot areas remains unclear. Using a prospective cohort study design, 225 individuals were enrolled, re-vaccinated with two doses of Shanchol™ regardless of previous vaccination and followed-up for 90 days. Bloods collected at baseline before re-vaccination, at day 14 prior to second dosing and subsequently on days 28, 60, and 90. Vibriocidal assay was performed on samples collected at all five time points. Our results showed that anti-LPS and vibriocidal antibody titers increased at day 14 after re-vaccination and decreased gradually at 28, 60 and 90 across all the groups. Seroconversion rates were generally comparable in all treatment arms. We therefore conclude that vibriocidal antibody titers generated in response to re-vaccination still wane quickly irrespective of previous vaccination status. However, despite the observed decline, the levels of vibriocidal antibodies remained elevated over baseline values across all groups, an important aspect for Zambia where there is no empirical evidence as to the ideal time for re-vaccination.

Chlorophyll-a (Chla) is a crucial pigment in phytoplankton, playing a vital role in determining phytoplankton biomass and water nutrient status. However, in optically complex water bodies, Chla concentration is no longer the primary factor influencing remote sensing spectral reflectance signals, leading to significant errors in traditional Chla concentration estimation methods. With advancements in in-situ measurements, synchronized satellite data, and computer technology, machine learning algorithms have become popular in Chla concentration retrieval. Nevertheless, when using machine learning methods to estimate Chla concentration, abrupt changes in Chla values can disrupt the spatiotemporal smoothness of the retrieval results. Therefore, this study proposes a two-stage approach to enhance the accuracy of Chla concentration estimation in optically complex water bodies. In the first stage, a one-dimensional convolutional neural network (1DCNN) is employed for precise Chla retrieval, and in the second stage, the regression layer of the 1DCNN is replaced with Support Vector Regression (SVR). The research findings are as follows: (1) In the first stage, the performance metrics (R², RMSE, RMLSE, Bias, MAE) of the 1DCNN outperform state-of-the-art algorithms (OCI, SVR, RFR) on the test dataset. (2) After the second stage, the performance further improves, with the metrics achieving values of 0.892, 11.243, 0.052, 1.056, and 1.444, respectively. (3) In mid-to-high latitude regions, the inversion performance of 1DCNN\SVR is superior to other algorithms, exhibiting richer details and higher noise tolerance in nearshore areas. (4) 1DCNN\SVR demonstrates high inversion capabilities in water bodies with medium to high nutrient levels.

This study unveils verapamil's compelling cytoprotective and proliferative effects on pancreatic β-cells amidst diabetic stressors, spotlighting its unforeseen role in augmenting cholecystokinin (CCK) expression. Through rigorous investigations employing MIN6 β-cells and zebrafish models under type 1 and type 2 diabetic conditions, we demonstrate verapamil's capacity to significantly boost β-cell proliferation, enhance glucose-stimulated insulin secretion, and fortify cellular resil-ience. A pivotal revelation of our research is verapamil's induction of CCK, a peptide hormone known for its role in nutrient digestion and insulin secretion, which signifies a novel pathway through which verapamil exerts its therapeutic effects. Furthermore, our mechanistic insights reveal that verapamil orchestrates a broad spectrum of gene and protein expressions pivotal for β-cell survival and adaptation to immune-metabolic challenges. In vivo validation in a zebrafish larvae model confirms verapamil's efficacy in fostering β-cell recovery post-metronidazole inflic-tion. Collectively, our findings advocate for verapamil's reevaluation as a multifaceted agent in diabetes therapy, highlighting its novel function in CCK upregulation alongside enhancing β-cell proliferation, glucose sensing, and oxidative respiration. This research enriches the therapeutic landscape, proposing verapamil not only as a cytoprotector but also as a promoter of β-cell re-generation, thereby offering fresh avenues for diabetes management strategies aimed at pre-serving and augmenting β-cell functionality.

The effects of ELICE16INDURES, a well-known plant conditioner developed by the Research Institute for Medicinal Plants and Herbs Ltd. Budakalasz, Hungary, were studied in a soybean population. The active ingredients of the compound have been selected to help elicit general immunity in plants without pathogenic damage, thereby roborizing the healthy plant population and preparing it for possible future biotic stressors. Here we have analyzed changes in the expression levels of genes encoding enzymes involved in the catalysis of metabolic pathways that induce and regulate PAMP-triggered immunity (PTI) at two different time points and treatments. Twenty-three different enzymes were analyzed that catalyze different metabolic pathways, such as the biosyntheses of jasmonic acid, salicylic acid, ethylene, phenylpropanoid, flavonoid, and phytoalexin biosynthesis and cellular detoxification processes. Bioinformatical softwares werw used to analyze the results. It has been found that some of the primary defense mechanisms (e.g., Mitogen-Activated-Protein Kinase (MAPK) cascade, jasmonic acid biosynthesis, flavonoid and phytoalexin biosynthesis, etc.) that intensify following the attack of pathogens can be activated without the intrusion of the actual pathogen by an immunochemical. Thus, we proved that plant resistance can be artificially conditioned.

Cathinone is a natural stimulant found in Catha edulis and commonly used in new psychoactive substances. The objective of this study was to examine the disposition kinetics and metabolic profile of cathinone and its metabolite cathine through a single oral dose of cathinone administration in rats. Cathine and cathinone concentrations were identified and quantified using ion trap liquid chromatography (LC-IT/MS), while the metabolic profile was determined using the quadrupole time of flight UPLC-QTOF/MS method in the serum, brain, lung, liver, kidney, and heart over a period of 0, 0.5, 2.5, 6, 12, 24, 48, and 72 hours. The findings revealed a dynamic interplay between the pharmacokinetics of cathinone and its impact on organ-specific biomarkers. The distribution of cathinone and cathine was determined in serum, brain, heart, lung, kidney, and liver. The highest concentration of cathinone was found in the kidney at 1438.6 ug/L. It gradually decreased to 1.97 within 48 hours and disappeared after 72 hours. Within half an hour, cathinone levels in the lungs, liver, and heart were found to be 859, 798.9, and 385.8 ug/L, respectively. However, within 2.5 hours, these levels decreased to 608.1, 429.3, and 309.1 ug/L and kept decreasing until they became undetectable after 24 hours. The concentration of cathinone in the rat brain reduces quickly, dropping to undetectable levels within six hours, with levels decreasing from 712.7 ug/L after just 30 minutes. In the brain and serum, cathine reached its highest levels at 2.5 hours, while in other organs, it peaked at 0.5 hours. This indicates that the conversion of cathinone to cathine is slower in the brain and serum. The study found that cathinone's pharmacokinetics have a significant impact on organ-specific biomarkers. After administering the cathinone, there was a sharp change in biomarker levels, particularly in the liver and brain, during the initial hours. It is essential to investigate the correlation between the changes in biomarkers found in the brain and the levels of cathinone and cathine. The results have significant implications for drug development, pharmacovigilance, and clinical practices involving cathinone. In conclusion, this comprehensive analysis of cathinone's impact on organ-specific biomarkers provides a basis for informed decision-making in medical practices and further research into the cathinone's pharmacological properties.

The Kuroshio Extension(KE) System exhibits highly energetic mesoscale phenomena, but the impact of mesoscale eddies on marine ecosystems and biogeochemical cycling is not well understood. This study utilizes remote sensing and Argo floats to investigate how eddies modify surface and subsurface chlorophyll (Chl-a) concentrations. On average, cyclones (anticyclones) induce positive (negative) surface Chl-a anomalies, particularly in winter. This occurs because cyclones (anticyclones) lift (deepen) isopycnals and nitrate into (out of) the euphotic zone, stimulating (depressing) the growth of phytoplankton. Consequently, cyclones (anticyclones) result in greater (smaller) subsurface Chl-a maximum (SCM), depth-integrated Chl-a, and depth-integrated nitrate. The positive (negative) surface Chl-a anomalies induced by cyclones (anticyclones) are mainly located near (north of) the main axis of the KE. The second and third mode represent monopole Chl-a patterns within eddy centers corresponding to either positive or negative anomalies, depending on the sign of the principal component. Chl-a concentrations in cyclones (anticyclones) above the SCM layer are higher (lower) than the edge values, while those below are lower (higher), regardless of winter variations. The vertical distributions and displacements of Chl-a and SCM depth are associated with eddy pumping. In terms of frequency, negative (positive) Chl-a anomalies account for approximately 26% (18%) of the total cyclones (anticyclones) across all four seasons. The opposite phase suggests that nutrient supply resulting from stratification differences under convective mixing may contribute to negative (positive) Chl-a anomalies in cyclone (anticyclone) cores. Additionally, the opposite phase can also be attributed to eddy stirring, trapping high and low Chl-a, and/or eddy Ekman pumping. Based on OFES outputs, the seasonal variation of nitrate from winter to summer primarily depends on the effect of vertical mixing, indicating that convective mixing processes contribute to an increase (decrease) in nutrients during winter (summer) over the KE.

The radiation-induced optical absorption at 1.5-5.5 eV (up to the beginning of fundamental absorption) has been analyzed in CVD diamond disks exposed to 231-MeV 132Xe ions with four fluences from 1012 to 3.81013 cm-2. The 5-mm diameter samples (thickness 0.4 mm) were prepared by Diamond Materials, Freiburg (Germany), average grain size at growth site was around 80 m, the range of xenon ions was R= 11.5 m. The intensity of several bands grows with ion fluence thus confirming radiation-induced origin of the defects responsible for these bands. The recovery of radiation damage has been investigated via isochronal (stepwise) thermal annealing procedure up to 650°C, while all spectra were measured at room temperature. Based on these spectra, the annealing kinetics of several defects, in particular carbon vacancies (GR1 centers with a broad band 2 eV) and complementary C-interstitial-related defects ( 4 eV), as well as vacancies located nearby nitrogen substitutional atoms (narrow bands around 2.5 eV) have been constructed. The experimental kinetics have also been analyzed in terms of the diffusion-controlled bimolecular reactions. The migration energies of tentatively interstitial atoms (mobile components in recombination process) are obtained, their dependence on the irradiation fluences is discussed.

The grain-to-grain stress vertically in sediments is given by the overburden less the pore fluid pressure, σ, divided by the fraction of the horizontal area which is the supporting matrix , (1 − φ), where φ is the porosity. It is proposed that the fractional reduction of this ratio, Λ, with time is given by the product of φ 4m/3 , (1 − φ) 4n/3 , and one or more Arrhenius functions A exp(−E/RT ) with m and n close to 1. This proposal is tested for shale sections in six wells from around the world for which porosity-depth data are available. Good agreement is obtained above 30-40 C and porosities less than 0.5. Single activation energies for each well are obtained in the range 15-33 kJ/mole, close to pressure solution of quartz, 24 kJ/mol. Values of m and n are in the range 1 to 0.8, indicating nearly fractal pore-matrix spaces and water-wet interfaces. Results are independent of over- or under-pressure of pore water. This model explains shale compaction quantitatively. Given porosity-depth data and accurate activation energy, E, one can infer paleo-geothermal-gradient and from that organic maturity, thus avoiding unnecessary drilling.

Perilla frutescens leaves are expected to exhibit antioxidant activity and amyloid-β (Aβ) aggregation inhibitory activity due to the presence of polyphenol-type compounds, etc. These activities fluctuate daily; however, measuring the contents of constituents and functionalities is cumbersome and unsuitable for instantaneous measurements in the field. In this study, we developed a facile method to analyze the activity and content of the components in leaves on-site based on the fluorescence spectra obtained by irradiating the perilla leaves with excitation light. The constituent contents (Chlorophyl (Chl), Total polyphenol content (TPC), Total flavonoid content (TFC), rosmarinic acid (RA) and functional properties DPPH radical scavenging activity, ferric reducing antioxidant power (FRAP), oxygen radical absorbance capacity (ORAC), Aβ aggregation inhibitory activity) were evaluated using established analytical techniques. The correlation between the fluorescence spectrum and the contents and activities was calculated using normalized difference spectral index (NDSI), ratio spectral index (RSI), and difference spectral index (DSI) analyses. We identified a predictive model with a high coefficient of determination R² ≥ 0.57 for content of the constituents, and R² ≥ 0.49 for functional properties. This allows convenient, simultaneous, and non-destructive monitoring of the constituent contents and the functionalities of perilla leave and a simple harvest-time diagnosis. The model established using this method is simple and suggesting that it can simultaneously infer the constituents and functionalities of perilla leaves.

Master equations define the dynamics that govern the time evolution of various physical processes on lattices. In the continuum limit, master equations lead to Fokker-Planck partial differential equations that represent the dynamics of physical systems in continuous spaces. Over the last few decades, nonlinear Fokker-Planck equations have become very popular in condensed matter physics and in statistical physics. Numerical solutions of these equations require the use of discretization schemes. However, the discrete evolution equation obtained by the discretization of a Fokker-Planck partial differential equation depends on the specific discretization scheme. In general, the discretized form is different from the master equation that has generated the respective Fokker-Planck equation in the continuum limit. Therefore, the knowledge of the master equation associated with a given Fokker-Planck equation is extremely important for the correct numerical integration of the latter, since it provides a unique, physically motivated discretization scheme. This paper shows that the Kinetic Interaction Principle (KIP) that governs the particle kinetics of many body systems, introduced in [G. Kaniadakis, Physica A 296, 405 (2001)], univocally defines a very simple master equation that in the continuum limit yields the nonlinear Fokker-Planck equation in its most general form.

The lab-on-a-chip concept, enabled by microfluidic technology, promises the integration of multi-ple discrete laboratory techniques into a miniaturised system. Research into microfluidics has generally focused on the development of individual elements of the total system (often with rela-tively limited functionality), without full consideration for integration into a complete fully opti-mised and miniaturised system. Typically, the operation of many of the reported lab-on-a-chip devices is dependent on the support of a laboratory framework. In this paper, a demonstrator platform for routine laboratory analysis is designed and built, which fully integrates a number of technologies into a single device with multiple domains such as fluidics, electronics, pneumatics, hydraulics, and photonics. This facilitates the delivery of breakthroughs in research, by incorpo-rating all physical requirements into a single device. To highlight this proposed approach, this demonstrator microsystem acts as a fully integrated biochemical assay reaction system. The re-sulting design determines enzyme kinetics in an automated process and combines reservoirs, three-dimensional fluidic channels, optical sensing, and electronics in a low-cost, low-power and portable package.

Background: diabetic nephropathy (DN) is a serious complication of diabetes mellitus and a common cause for end stage renal disease. Autophagy has a defensive role against kidney damage caused by hyperglycemia. The mesenchymal stem cells (MSCs) derived exosomes are currently considered as a new promising therapy in chronic renal injury. However, the renal protective mechanism of exosomes on DN has not been completely understood. We examined the potential role of MSCs derived exosomes in enhancement of autophagy activity and its effect on DN. In our study we used five groups of rats; control, DN, DN treated with exosomes, DN treated with 3-methyladenine (3-MA) and chloroquine (inhibitors of autophagy) and DN treated with 3-methyladenine (3-MA) and chloroquine and exosomes groups. We assessed renal functions, morphology and fibrosis. Moreover, autophagy markers; mTOR, Beclin-1, light chain-3 (LC3-II), and LC3-II/LC3-I ratio were detected. Additionally, electron microscopy was used for detection of autophagosomes. Results: Exosomes markedly improved the renal functions and showed histological restoration of renal tissues with significant increase in LC3 and Beclin-1 besides the significant decrease in mTOR and fibrotic markers expression in renal tissue. All previous effects were partially abolished by the autophagy inhibitor, chloroquine and 3-MA. Conclusions: we conclude that autophagy induction by exosomes could attenuate DN in a rat model of streptozotocin-induced diabetes mellitus.

β-apopicropodophyllin (APP), a derivative of podophyllotoxin (PPT), has been identified as a potential anti-cancer drug. This study tested whether APP acts as an an-ti-cancer drug and can sensitize colorectal cancer (CRC) cells to radiation treatment. APP had an anti-cancer effect against the CRC cell lines HCT116, and DLD-1, SW480 and COLO320DM with IC50 values of 7.88 nM, and 8.22 nM, 9.84 nM and 7.757 nM, respec-tively induction of DNA damage. Colonogenic and cell counting assays indicated that the combined treatment of APP and γ-ionizing radiation (IR) showed greater retardation of cell growth than either alone, suggesting that APP sensitizes CRC cells to IR. Annexin V-propidium iodide (PI) assays and immunoblot analysis showed that the combined treatment of APP and IR increased apoptosis in CRC cells compared with either APP or IR alone. Results obtained from the xenograft experiments also indicated that the combination of APP and IR enhanced apoptosis in in vivo animal model. Apoptosis induction by the combined treatment of APP and IR resulted from reactive oxygen species (ROS). Inhibition of ROS by N-acetylcysteine (NAC) restored cell viability and decreased the induction of apoptosis by APP and IR in CRC cells. Taken together, these results indicate that a combined treatment of APP and IR might promote apoptosis by inducing ROS in CRC cells.

The dispersal potential of crown-of-thorns starfish (CoTS) larvae is important in understanding both the initiation and spread of population outbreaks, and is fundamentally dependent upon how long larvae can persist while still retaining the capacity to settle. This study quantified variation in larval survivorship and settlement rates for CoTS maintained at three different chlorophyll concentrations (0.1, 1.0 or 10.0 µg.L^-1), achieved by varying densities of single-celled flagellate phytoplankton, Proteomonas sulcata. Based on the larval starvation hypothesis we expected that low to moderate algal concentrations would significantly constrain both survival and settlement. CoTS larvae were successfully maintained for up to 50 days post-fertilization, but larval survival differed significantly between treatments. Survival was greatest at intermediate (1.0 µg.L^-1) chlorophyll concentrations, and lowest at highest (10.0 µg.L^-1) chlorophyll concentrations. Rates of settlement were also highest at intermediate (1.0 µg.L^-1) chlorophyll concentrations and peaked at 22 days post-fertilization. Peak settlement was delayed at low chlorophyll concentrations, probably reflective of delayed development, but there was no evidence of accelerated development at high chlorophyll concentrations. CoTS larvae were capable of settling 17-43 days post-fertilization, but under optimum conditions with intermediate chlorophyll concentrations, peak settlement occurred at 22 days post-fertilization. Moderate increases in nutrient concentrations and algal densities may increase the number of CoTS that effectively settle, but are unlikely to influence dispersal dynamics.

The flavin derivatives 10‐methyl‐isoalloxazine (MIA) and 6-fluoro-10-methyl-isoalloxazine (6F-MIA) were encapsulated in two alternative metal-organic frameworks, (MOFs) MIL53(Al) and MOF5, using a post-synthetic, diffusion-based incorporation into microcrystalline MIL-53 powders and an in-situ approach during the MOF-5 synthesis. The flavin@MOF composites were analyzed by powder X-ray diffractometry (PXRD), N2-sorption studies and time-resolved fluorescence spectroscopy and microscopy. The maximum amount of flavin dye incorporation is 3.9 wt% for MIA@MIL-53(Al) and 1.5 wt% for 6F-MIA@MIL-53(Al), 0.85 wt% for MIA@MOF-5 and 27.6 wt% for 6F-MIA@MOF-5. The emission wavelengths of all flavin@MOF composites mostly correspond to the wavelengths of the flavins in solution. Time-resolved spectroscopy showed that the fluorescence lifetime of flavin@MOF of 2-4.7 ns also corresponds to those in solution but is significantly prolonged compared to the solid flavin dyes with less than 1 ns, thereby confirming the concept of "solid solutions" for dye@MOF composites. The fluorescence quantum yield (ΦF) of the flavin@MOF composites is about half of the solution but is significantly higher compared to the solid flavin dyes. Both the fluorescence lifetime and quantum yield of flavin@MOF decrease with the flavin loading in MIL-53. Theoretical calculations using plane-wave and QM/MM methods are in good correspondence with the experimental results and explain the electronic structures as well as the photoluminescence/photophysical properties of crystalline MIA and the flavin@MOF composites. In the solids flavins π-stacking interactions of the molecules lead to a charge transfer state with low oscillator strength resulting in aggregation-caused quenching (ACQ) with low lifetimes and quantum yields. In the MOF pores the flavin molecules are separated and the computed MIA@MOF structures do not find π-stacking interactions to the pore walls but only weak van-der-Waals contacts which reasons the enhanced fluorescence lifetime and quantum yield of the flavins in the composites compared to their neat solid state. The flexible MOF MIL-53(Al) was optimized essentially to the experimental large-pore form in the guest-free state with QuantumEspresso (QE) and with MIA molecules in the pores the structure contracted to close to the experimental narrow-pore form which was also confirmed by PXRD. In summary, the incorporation of flavins in MOFs yields solid-state materials with enhanced rigidity, stabilized conformation and reduced aggregations of the flavins, leading to increased fluorescence lifetime and quantum yield as controllable photo-luminescent and photo-physical properties.

Fluorescein anisotropy, which is a widely used technique to study the folding state of proteins or affinity of ligands, is used in the present work to study the temperature sensing of fluid in a microchannel, by adding fluorophore in the fluid. Fluorescein was used as a temperature probe, while glycerol-aq. ammonia was used as a working fluid. Fluorescence anisotropy of fluorescein were measured by varying various parameters. Apart from this, a comparison of fluorescence anisotropy and fluorescence intensity is also performed.

Dibutyl phthalate (DBP) is widely used as a plasticizer in the production of polymeric materials to give them flexibility, strength and extensibility. However, due to its negative impact on human health, in particular, reproductive function and fetal development, the content of DBP must be controlled in food and environmental objects. The present study aims to develop a sensitive, fast and simple polarization fluorescent immunoassay (FPIA) using monoclonal antibodies derived against DBP (MAb-DBP) for its detection in open waters. New conjugates of DBP with various fluorescein derivatives were obtained and characterized: 5-aminomethylfluorescein (AMF) and dichlorotriazinylaminofluorescein (DTAF). The advantages of using the DBP-AMF conjugate in the FPIA method are shown, the kinetics of binding of this drug with antibodies is studied, the analysis is optimized, and the concentration of monoclonal antibodies is selected for sensitive analysis - 16 nM. The calibration dependence of the fluorescence polarization signal for the detection of DBP was obtained. The observed IC50 (40 ng/mL) and LOD (10 ng/mL) values were improved by a factor of 35 for the previously described FPIA using polyclonal antibodies. This technique was tested by the added/found method, the percentage of DBP discovery in water ranged from 85 to 110%. Using the developed method, real water samples from Lake Onega were tested, and a good correlation was shown between the results of the determination of DBP by the FPIA method and GC-MS/MS. Thus, the FPIA method developed in this work can be used to determine DBP in open water reservoirs.

The effect of high temperature (HT) stress on nicotine biosynthesis in Nicotiana attenuata was examined. Nicotine content was measured in mature leaves, young sink leaves and in roots from well-watered plants grown at 25 °C as controls and from plants exposed to 38 °C and 43 °C temperatures applied for 24, 48, 72 and 96-hr duration. At 38 °C, all leaf nicotine levels were significantly less than control plants for up to 72-hr exposure but rose sharply thereafter to levels significantly greater than controls with 96-hr exposure. In contrast, plants exposed to 43 °C never exhibited a reduction in leaf nicotine content and showed a significant increase in content with just 48-hr exposure. When radioactive 11CO2 was administered to plants, HT stress significantly reduced fixation. Furthermore, radiocarbon flux analysis revealed that ‘new’ C partitioning (as 11C) into the [11C]-amino acid pool was significantly reduced with HT stress as were yields of [11C]-aspartic acid, an important amino acid in nicotine biosynthesis, and its beta-amido counterpart [11C]-asparagine significantly reduced. In contrast, [12C]-aspartic acid levels appeared unaffected at 38 °C but were significantly elevated at 43 °C relative to controls. Additionally, [12C]-asparagine levels were significantly elevated at both stress temperatures. Finally, leaf total soluble protein (TSP) was reduced 39% with long exposures to both stress temperatures. However, Ribulose-1,5-bisphosphate carboxylase/oxygenase (Rubisco) which was 41% TSP appeared unaffected by HT stress. Altogether, these results support the theory that plant proteins other than Rubisco degrade at elevated temperatures freeing up essential amino acids supporting the nicotine biosynthetic machinery, and while feedback might downregulate de novo amino acid synthesis from ‘new’ C resources, more than likely plant C/N rebalancing caused by HT reductions in C input restricted N uptake, which in turn, limited this process.

Monitoring lakes in high-latitude areas can provide a better understanding of freshwater systems sensitivity and accrete knowledge on climate change impacts. Phytoplankton are sensitive to various conditions: warmer temperatures, earlier ice-melt and changing nutrient sources. Satellite imagery can monitor algae biomass over large areas. The detection of chlorophyll a (chl-a) concentrations in small lakes is hindered by the low spatial resolution of conventional ocean colour satellites. The short time-series of the newest generation of space-borne sensors (e.g. Sentinel-2) is a bottleneck for assessing long-term trends. Although previous studies have evaluated the use of high-resolution sensors for assessing lakes' chl-a, it is still unclear how the spatial and temporal variability of chl-a concentration affect the performance of satellite estimates. We discuss the suitability of Landsat (LT) 30-m resolution imagery to assess lakes' chl-a concentrations under varying trophic conditions, across extensive high-latitude areas in Finland. We use in situ data obtained from field campaigns in 19 lakes and generate remote sensing estimates of chl-a, taking advantage of the long-time span of the LT 5 and 7 archives, from 1984 to 2017. Our results show that linear models based on LT data can explain approximately 50 % of the chl-a interannual variability. However, we demonstrate that the accuracy of the estimates is dependent on the lake's trophic state, with models performing in average twice as better in lakes with higher chl-a concentration (> 20 µg/l) in comparison with less eutrophic lakes. Finally, we demonstrate that linear models based on LT data can achieve high accuracy (R2 = 0.9; p-value < 0.05) in determining lakes' annual mean chl-a concentration, allowing the mapping of the trophic state of lakes across large regions. Given the long time-series and high spatial resolution, LT-based estimates of chl-a provide a tool for assessing the impacts of environmental change.

This paper investigates the density, phase composition, microstructure and mechanical properties (microhardness, fracture toughness) of binderless WC + SiC ceramics obtained by conventional pressureless sintering (CPS) and Spark Plasma Sintering (SPS). α-WC nanopowders obtained by DC arc plasma chemical synthesis and β-SiC powders have been used as raw materials. The content of SiC particles was 1, 3, 5% wt. Excess graphite (0.3, 0.5% wt.) was added to α-WC nanopowders to decrease the volume fraction of W2C particles that negatively affect the mechanical properties of ceramics. WC + 1% wt. SiC + 0.3% wt. C ceramics are shown to have a homogeneous fine-grained microstructure, high relative density, increased microhardness and Palmquist fracture toughness. The CPS and SPS activation energies of WC + SiC nanopowders at an intensive shrinkage stage are determined using the Young-Cutler model. The effect of carbon and SiC particles on the CPS and SPS activation energies of tungsten carbide nanopowders has been analyzed. The CPS activation energies of WC, WC + C and WC + SiC + C nanopowders are shown to be closer to the carbon diffusion activation energy along α-WC grain boundaries. The SPS activation energies of WC and WC + SiC nanopowders turn out to be lower than the carbon grain boundary diffusion activation energy of α-WC.

Colombia is the world's leading producer of mild washed arabica coffee and produces 12.6 million bags of green coffee, but at the same time 784,000 tons of waste biomass are dumped in open fields, of which only 5% is recovered or used. The objective of this project was to evaluate the production of platform chemicals from these coffee wastes. To achieve this, biomass characterization was carried out using proximate analysis, ultimate analysis and structural analysis. Hydrothermal valorization was carried out at a temperature range of 120-180 °C (LHW) and 180-260 °C (HTC) for one hour, the platform chemicals obtained were quantified by HPLC-IR, monitored by pH and conductivity, and the solid fraction was characterized by monitoring the functional groups in IR spectroscopy, and elemental analysis. Hydrolysis processes were obtained from 150 °C, production of platform chemicals from 180 °C and maximum concentration at 180 °C-4h, over 200 °C degradation of the products in the liquid fraction starts to take place. Homogeneous basic and acid catalysts were used to improve the yields of the reaction. The kinetics of the hydrolysis of lignocellulosic structures to sugars were also analyzed and described, and reaction orders of 1 (LHW), 3 (HTC) and their respective reaction rate equations were reported.

Faraday's Law of induction is often stated as "a change in magnetic flux causes an EMF"; or, more cautiously, "a change in magnetic flux is associated with an EMF"; It is as well that the more cautious form exists, because the first "causes" form can be shown to be incompatible with the usual expression for EMF. This is not, however, to deny the causality as reasonably inferred from experimental observation ­ it is the equation for Faraday's Law of induction which does not represent the claimed cause-and-effect relationship. Here we investigate a selection of different approaches, trying to see how an explicitly causal mathematical equation, which attempts to encapsulate the "a change in magnetic flux causes ..." idea, might arise.

Gold nanohole arrays are periodic metastructures gathering huge interest for biosensing applica-tions. The grating-like structure defines their plasmonic mode features and their angular disper-sion can be used to highlight efficiently their interaction with the fluorescence emission of a properly tuned fluorophore. Resorting to a properly tuned/engineered/optimised plasmonic na-nohole array and a commercial organic dye, we performed an accurate resolved angle-resolved optical characterization. The plasmonic fingerprints was consequently identified as a modification of the dye photoluminescence signal in terms of both spectral redistribution and enhancement. Interestingly, by analyzing the results, an advantageous measurement configuration can be iden-tified to better engineer a suitable platform for efficiency maximization in plasmon-enhanced flu-orescence-based applications. Therefore, the coupling mechanism with the plasmonic modes, and nanostructure properties can be carefully co-optimized.

Prior studies have focused on the overall behavior of randomly moving particle swarms. However, the characteristics of ubiquitous special particle swarms that form in these swarms remain unknown. This study demonstrates a generalized diffusion equation for randomly moving particles that considers the velocity and location aggregation effects in a special circumstance (that is, in a moving reference frame R_u relative to a stationary reference frame R₀). This equation can be approximated as the Schrodinger equation in the microcosmic case and describes the kinetics of the total mass distribution in the macrocosmic case. The predicted density distribution of the particle swarm in the stable aggregation state is consistent with the total mass distribution of massive, relaxed galaxy clusters (at least in the range of r < r_s), preventing cuspy problems in the empirical Navarro-Frenk-White (NFW) profile. This article is helpful for inspiring people to think about the essence of universal gravitation.

Compartmental analysis is the mathematical framework for the modelling of tracer kinetics in dynamical Positron Emission Tomography. This paper provides a review of how compartmental models are constructed and numerically optimized. Specific focus is given on the identifiability and sensitivity issues and on the impact of complex physiological conditions on the mathematical properties of the models.

From the theory of relativistic chemical kinetics [M. W. Baig, Int. J. Mod. Phys. B 31, 1750177 (2017)] relativistic thermodynamics and kinetics for electrode processes have been developed to explain time dilation for electrode processes. For a moving observer moving at fractions of the speed of light, cell potential is observed to decrease. This results in the slower oxidation and reduction of ions at the respective electrodes. The newly formulated Lorentz transformation of the electrode and cell potential is explained in terms of generation of spin 2-boson “gravitons” from fusion of spin-1 boson “virtual-photons” mediating electrostatic force of attraction between ions and electrodes. It is postulated that birth of spin 2-boson i.e. gravitons is followed by their eventual escape in any of higher 4+n dimensions. To demonstrate the effectiveness of the present theory, the Daniel cell is considered as a numerical example.

Gold- and MnO₂- nanozymes are well-known for their enzyme-like activity. In this regard, initially, gold- and MnO₂- nanozymes were synthesized by simple and green methods. Afterward, the kinetic studies were performed using the Michaelis–Menten model for both gold- and MnO₂- nanozymes. The kinetic parameters including K_m and V_max were calculated via the construction of the linear plot of Lineweaver–Burk for both nanozymes. The results showed a V_max and K_m of 185 nM sec^-1 and 47 nM sec^-1 for the gold- and MnO₂- nanozymes, in order. The ratio of V_max(gold)/V_max(MnO₂) was found to be about 4.0 which pointed that the catalytic efficiency of gold-nanozymes is 4.0-fold higher than the catalytic efficiency of MnO₂- nanozymes. The K_m value was found to be 0.72 mM and 1.6 mM for the as-prepared gold- and MnO₂- nanozymes, respectively, and the K_m of MnO₂-nanozymes is 2.2-fold higher than that of gold nanozymes. Since the Km shows the affinity of substrate for binding to nanozyme active nodes (lower K_m=higher affinity), it is consultable that the substrate affinity toward MnO₂-nanozymes is 2.2-fold lower than that of the gold-nanozymes. Considering the above results, the as-prepared gold nanozymes are very stronger peroxidase-like mimics than the metal oxide MnO₂-nanozymes.

Considerable attention has been given to the research field of bioorganometallic chemistry, which is a hybrid chemistry field between biology and organometallic chemistry. The introduction of biomolecules, which have hydrogen bonding sites and chiral centers, into organometallic compounds is considered to be a promising strategy to construct chirality-organized bioorganometallic conjugates. This feature paper sketches an outline of induction of helical chirality into bioorganometallic conjugates. Topics covered include control of the helical chirality of 1,n’-disubstituted ferrocene moieties in ferrocene-dipeptide conjugates and the chirality induction of the Au(I)–Au(I) axis in the dinuclear organogold(I)-uracil conjugates.

Papillary thyroid cancer (PTC) is the most common endocrine malignancy which diagnosis and recurrences still challenge clinicians. New perspectives to overcome those issues could come from the study of extracellular vesicles (EVs) populations and content. Here, we aimed to elucidate the heterogeneity of EVs circulating in tumor and the changes in their microRNA content during cancer progression. Using a mouse model expressing BRAF^V600E, we isolated and characterized EVs from thyroid tissue by ultracentrifugations and elucidated their microRNA content by small RNA sequencing. Cellular origin of EVs was investigated by ExoView and that of deregulated EV-microRNA by qPCR on FACS-sorted cell populations. We found that PTC released more EVs bearing epithelial and immune markers, as compared to healthy thyroid, and that changes in EV-microRNAs abundance were mainly due to their deregulated expression in thyrocytes. Pathway analysis showed that the more abundant EV-microRNAs could impact on immune processes. Altogether, our work provides a full description of in vivo-derived EVs produced by, and within, normal and cancerous thyroid. We elucidated the global EV-microRNAs signature, the dynamic loading of microRNAs in EVs upon BRAF^V600E induction, and their cellular origin. Thyroid tumor-derived EV-microRNAs could support the establishment of a permissive immune microenvironment.

Alnus glutinosa is important woody plant in Lithuanian forest ecosystems. Knowledge of fluorescence properties of black alder pollen is necessary for scientific and practical purposes. By the results of the study we aimed to evaluate possibilities of identifying Alnus glutinosa pollen fluorescence properties by modeling ozone effect and applying two different fluorescence-based devices. To implement experiments, black alder pollen was collected in a typical habitat during the annual flowering period in 2018-2019. There were three groups of experimental variants, which differed in the duration of exposure to ozone, conditions of pollen storage before the start of the experiment, and the experiment start time. Data for pollen fluorescence analysis were collected using two methods. The microscopy method was used in order to evaluate the possibility of employing image analysis systems for investigation of pollen fluorescence. The second data collection method is related to the automatic device identifying pollen in real-time, which uses the fluorescence method in the pollen recognition process. Data were assessed employing image analysis and principal component analysis (PCA) methods. Digital images of ozone-exposed pollen observed under the fluorescence microscope showed the change of the dominant green colour towards the blue spectrum. Meanwhile, the automatic detector detects more pollen whose fluorescence is at the blue light spectrum. It must be noted that assessing pollen fluorescence several months after exposure to ozone, no effect of ozone on fluorescence remains.

We present here a five hours experimentation of a didactical path about the electromagnetic induction addressed to students of the last year of an Italian scientific high school and oriented to better understand the physical origin of the induced electromotive force. The expression of the induced electromotive force as the sum of the term linked to the time variation of the magnetic field and of the motional one has been obtained in a detailed way, still suitable for presentation at high school. Many examples have been proposed to the students in order to clarify the conceptual physical knots. The students’ responses to a 6-questions multiple choice questionnaire have been analyzed. It emerged that our approach is concretely feasible although we find the well-known difficulties in calculating flux and circulation of a vector field. Furthermore, it emerged that an integral approach to the problem masks the understanding of the nature of the forces acting locally on the charges. Hence our proposal of a “redefinition” of the induced electric field in terms of the magnetic vector potential is also presented.

The current study investigated the use of two-dimensional spatial distribution mapping representing the chlorophyll-a level in a river generated via an unmanned aerial vehicle (UAV) and an unmanned surface vehicle (USV). A domestically developed UAV (Remo-M, Uconsystem Inc., Korea) and a USV developed by our research team were used to collect data from the Nae Seong stream in Korea. An adaptation of the “Data Cleaner” tool was developed and used for USV data processing and analysis. The operation of the autonomous USV was successful. Four previously described indices for quantifying algal blooms in rivers were utilized to create chlorophyll-a images, the normalized difference vegetation index (NDVI), the normalized green red difference index, the green normalized difference vegetation index (GNDVI), and the normalized difference red edge index. The suitability of the linear regression analysis of the correlation between the spectral indices obtained using the UAV and the in situ chlorophyll-a data obtained using the USV was evaluated with the coefficient of determination (R2) at a significance level of p &lt; 0.001. In field application and correlational analysis the NDVI was strongly correlated with chlorophyll-a (R2 = 0.88, p < 0.001), and the GNDVI was moderately correlated with chlorophyll-a (R2 = 0.74, p < 0.001). The map of chlorophyll-a was successfully quantified using the UAV and USV hybrid platforms.

This study explores the use of Bayesian Neural Networks (BNNs) for estimating chlorophyll-a concentration ([CHL-a]) from remotely sensed data. The BNN model enables uncertainty quantification, offering additional layers of information compared to traditional ocean colour models. An extensive in situ bio-optical dataset is utilized, generated by merging 27 data sources across the world’s oceans. The BNN model demonstrates remarkable capability in capturing mesoscale features and ocean circulation patterns, providing comprehensive insights into spatial and temporal variations in [CHL-a] across diverse marine ecosystems. In comparison to established ocean colour algorithms, such as Ocean Colour 4 (OC4), the BNN shows comparable performance in terms of correlation coefficients, errors, and biases when compared with the in situ data. The BNN, however, further provides critical information about the distribution of [CHL-a], which can be used to assess uncertainties in the prediction. Moreover, the BNN model’s ability to provide more information for coastal waters, especially with higher spatial resolution imagery, offers valuable advantages for marine research and management. By quantifying uncertainty, the model builds confidence in [CHL-a] predictions, even in regions with limited data coverage. This is reflected by the spread in the model predictions, where the BNN can detect a range of uncertainty bounds that reflect confidence in the retrievals. Introducing BNNs as probabilistic ocean colour models represents a significant advancement, enabling more accurate and reliable predictions of [CHL-a] in the global oceans.

The main bottleneck when performing computational fluid dynamics (CFD) simulations of combustion systems is the computation and integration of the highly non-linear and stiff chemical source terms. In recent times, machine learning has emerged as a promising tool to accelerate combustion chemistry, involving the use of regression models to predict the chemical source terms as functions of the thermochemical state of the system. However, combustion is a highly nonlinear phenomenon, and this often leads to divergence from the true solution when the neural network representation of chemical kinetics is integrated in time. This is because these approaches minimize the error during training without guaranteeing successful integration with ordinary differential equation (ODE) solvers. In this work, a novel neural ODE approach to combustion modeling, ChemNODE, is developed to address this issue. The source terms predicted by the neural network are integrated during training, and by backpropagating errors through the ODE solver, the neural network weights are adjusted accordingly to minimize the difference between the predicted and actual ODE solutions. It is shown that even when the dimensionality of the thermochemical manifold is trimmed to remove redundant species, the proposed approach accurately captures the correct physical behavior and reproduces the results obtained using the full chemical kinetic mechanism.

Damage and fibre misalignment of woven fabrics during discontinuous polymer processing remain challenging. To overcome these, a promising switchable elastomeric adherence gripper is introduced here. The inherent surface tackiness is utilized for picking and placing large sheets. Due to the elastomer’s viscoelastic material behavior, the surface properties depend on loading speed and temperature. Different peeling speeds result in different adherence strength of an interface between the gripper and the substrate. This feature is mechanically characterized and the viscoelastic behavior of the stamp is examined. Based on this experimental characterization, an empirical model is proposed. Furthermore, a discussion of the applicability and limitation of the elastomeric gripper is given.

Due to the accumulation of pesticides in the environment, the development of efficient strategies for their removal is of utmost importance. Activated carbons are currently seen as excellent candidates for adsorptive pesticide removal based on several beneficial properties, like a large surface area, developed porosity, and low price. However, a deep link between materials' properties and performance is still elusive. Here we focus on the kinetics of three organophosphate pesticides removal, aliphatic dimethoate and malathion and aromatic chlorpyrifos, using a series of carefully prepared activated carbon fibers. Used adsorbents have a wide range of specific surface areas, pore size distributions, and elemental content, allowing the establishment of the link between physicochemical properties and their performance as adsorbents. We use data analysis tools to link these properties and discuss their different roles in the removal of three structurally different yet extremely dangerous pesticides. The obtained results can guide the synthesis of novel adsorbents or rationally select adsorbents for specific target pollutants based on the physicochemical properties of adsorbents and the chemical structure of pollutants.

A novel method proposed in the production of Calophyllum inophyllum biodiesel has been investigated experimentally. In this study, we report the results of biodiesel processing with electromagnetic induction technology. The method used is to compare the results of Calophyllum inophyllum biodiesel processing between conventional, microwave and electromagnetic induction. The degumming, transesterification, and esterification process of the 3 methods are measured by stopwatch to obtain time comparison data. Characteristics of viscosity, density, and Fatty Acid Metil Ester (FAME) were obtained from testing of a Gas Chromatography-mass Spectrometry (GCMS) at the Polytechnic Chemistry Laboratory of the State of Malang. The results show that the biodiesel produced by this method satisfies the biodiesel standards and their characteristics are better than the biodiesel produced by conventional and microwave methods. The electromagnetic induction method also offers a fast and easy route to produce biodiesel with the advantage of increasing the reaction rate and improving the separation process compared to other methods. This advanced technology has the potential to significantly increase biodiesel production with considerable potential to reduce production time and costs.

Remediation of IT issues encoded into domain-specific or user-defined alerts occurring in cloud environments and customer ecosystems in a vast majority of cases suffers from accurate recommendations which could be timely supplied for recovery of performance degradations. That, of course, is hard to realize through furnishing those abnormality definitions with an appropriate expert knowledge which varies from one environment to another. At the same time, in a large proportion of support cases, the reported problems under Global Support Services (GSS) or Site Reliability Engineering (SRE) treatment ultimately go down to the product teams making them waste costly development hours on investigating self-monitoring metrics of our solutions. Therefore, the mean-time-to-resolution (MTTR) rates of problems/alerts are significantly impacted from lack of a systematic approach towards adopting AI Ops. That would imply building, maintaining, and continuously improving/annotating a data store of insights that ML models are trained and generalized across the whole customer base and corporate cloud services. Our ongoing study is in line with such a vision and validates an approach that learns the alert resolution patterns in such a global setting and explains them using interpretable AI methodologies. The knowledge store of causative rules is then applied in predicting potential sources of the application degradation reflected in an active alert instance. In this communication, we share our experiences with a prototype solution and up to date analysis demonstrating how root conditions are discovered with a high accuracy for a specific type of problem. It is validated against the historical data of resolutions performed by heavy manual development efforts. We also offer a Dempster-Shafer theory-based rule verification framework for experts as a what-if analysis tool to test their hypotheses about underlying environment.

Histidine is an essential amino acid with significant implications in human growth and neuromodulation. Its concentration within cells, when either elevated or reduced, can indicate different diseases. While various methods exist to measure increased histidine levels, there remains a significant lack of sensors capable of actively responding to histidine deficiency within cells and releasing strong signals. In this study, we exploited the high induction levels of the his operon in S. Typhimurium SL1344, a histidine auxotroph, within a histidine-deficient environment, to develop a specific bacterial sensor with sensitivity towards low histidine concentrations. The SL1344-pGEX sensor, with a high copy number, exhibited remarkable sensitivity and selectivity to histidine in the range of 0 to 50 μM. Notably, even a minute addition of histidine (approximately 2.5 μM) to the M9 medium led to observable fluorescence reduction, rendering it highly suitable for monitoring histidine-deficient cellular environments. This bacterial fluorescence sensor holds great potential for detecting changes in intracellular histidine concentrations during pathogenic bacterial infections and for assessing the impact of drugs on cellular metabolism.

Fluorescence microscopy is an important tool for disease diagnosis, often requiring costly optical components, such as fluorescence filter cubes and high-power light sources. Due to its high cost, conventional fluorescence microscopy cannot be fully exploited in low-income settings. Smartphone-based fluorescence microscopy becomes an interesting low-cost alternative, but raises challenges in the optical system. We present the development of a low-cost inverted laser fluorescence microscope, that uses a smartphone to visualize the fluorescence image of biological samples. Our fluorescence microscope uses a laser-based simplified optical filter system, that provides analog optical filtering capabilities of a fluorescence filter cube. Firstly, we validated our inverted optical filtering by visualizing microbeads labeled with three different fluorescent compounds or fluorophores, commonly used for disease diagnosis. Secondly, we validated the disease diagnosis capabilities, by comparing the results of our device with those of a commercial fluorescence microscope. We successfully detected and visualized Trypanosoma cruzi parasites, responsible of the Chagas infectious disease, and the presence of Antineutrophil cytoplasmic antibodies of the ANCA non-communicable autoimmune disease. The samples were labeled with the fluorescein isothiocyanate (FITC) fluorophore, one of the most commonly used for disease diagnosis. Our device provides a 400 X magnification and is at least two orders magnitude cheaper than conventional commercial fluorescence microscopes.

In this study, we evaluated chlorophyll fluorescence (CF) under two extreme illumination conditions at plant scale with a passive spectroradiometer. Fluorescence (F) was estimated by reading directly from radiance spectra of a variety of plants illuminated with light-emitting diode (LED) grow lights in the laboratory. Solar-induced fluorescence (SIF) was estimated from spectral measurements of the same plants under sunlight using the Fraunhofer Line Depth (FLD) method. Chlorophyll fluorescence yield (F_yield) and solar-induced fluorescence yield (SIF_yield) were calculated by normalizing F and SIF with absorbed photosynthetically active radiation (APAR). Two approaches to estimating APAR were compared: utilizing white reference spectra and reflected spectra versus white reference spectra combined with the fraction of absorbed photosynthetically active radiation (fPAR) derived from literature. Average F and SIF were different by a factor of approximately twenty-four (F = 0.110 ± 0.038 Wm⁻²μm⁻¹sr⁻¹ versus SIF = 2.60 ± 1.87 Wm⁻²μm⁻¹sr⁻¹). In contrast, the average normalized values F_yield and SIF_yield were within the margin of error of one another (F_yield = 0.022 ± 0.008 μm⁻¹sr⁻¹ and SIF_yield = 0.030 ± 0.020 μm⁻¹sr⁻¹). This study highlights the influence of APAR on CF and the importance of properly accounting for it when estimating yield and demonstrates the ability of two simple and portable experimental setups with a passive instrument to obtain fluorescence metrics.

The beta-galactoside-binding mammalian lectin galectin-1 can bind, via its carbohydrate recognition domain (CRD), various cell surface glycoproteins and has been implicated in a range of cancers. As a consequence of binding to sugar residues on cell surface receptors it has been shown to have a pleiotropic effect across many cell types and mechanisms resulting in immune system modulation and cancer progression. As a result, it has started to become a therapeutic target for both small and large molecules. In previous studies, we have used fluorescence polarisation (FP) assays to determine KD values to screen and triage small molecule glycomimetics that bind to the galectin-1 CRD. In this study surface plasmon resonance (SPR) was used to compare human and mouse galectin-1 affinity measures with FP as SPR has not been applied for compound screening against this galectin. Binding affinities for a selection of mono- and di-saccharides covering a 1,000-fold range correlated well between FP and SPR assay formats for both human and mouse galectin-1. It was shown that slower dissociation drove the increased affinity at human galectin-1 whilst faster association was responsible for the effects at mouse galectin-1. This study demonstrates that SPR is a sound alternative to FP for early drug discovery screening and determining affinity estimates. Consequently, it also allows association and dissociation constants to be measured in a high throughput manner for small molecule galectin-1 inhibitors.

: This study focuses on optimizing chlorophyll extraction techniques and strategically placing leaf disks to enhance chlorophyll concentration in sesame (Sesamum indicum L.) leaves. Thirty sesame genotypes, categorized into light green (LG), middle green (MG), and deep green (DG) pigment groups based on leaf coloration, were selected from a larger pool of field-grown accessions. The investigation involved determining optimal SPAD value index measurements, quantifying pigment concentrations, exploring extraction solvents, and selecting suitable leaf disk positions. Significant variations in chlorophyll content were observed across genotypes, greenness categories, and leaf disk positions. The categorization of genotypes into DG, MG, and LG groups revealed a correlation between leaf appearance and chlorophyll content. The study highlighted a consistent relationship between carotenoids and chlorophyll, indicating their role in adaptation to warm environments. Examination of leaf disk positions revealed a significant chlorophyll gradient along the leaf blade, emphasizing the need for standardized protocols. Chlorophyll extraction experiments identified DMSO and 96% ethanol, particularly the later incubated for 10 minutes at 85°C, as effective choices. This recommendation considers factors like cost-effectiveness, time efficiency, safety, and environmental regulations, ensuring consistent and simplified extraction processes. For higher chlorophyll extraction, focusing on leaf tips and the 75% position along the sesame leaf blade is suggested, consistently yielding higher chlorophyll content. Our findings therefore, underscores insightful knowledge on chlorophyll gradients and encouraging for standardized protocols, that enabling researchers to refine experimental designs for precise and comparable chlorophyll measurements. Recommended solvent choices ensure reliable outcomes in plant physiology, ecology, and environmental studies.

Using the fluorescent method in the modification of Krasnoyarsk State University, we study development (as chlorophyll content, ∑CHL) and photosynthetic activity of phytoplankton in seven large flat reservoir of the Volga River cascade (Russia) in August 2915–2017. In period of maximal warming of water, average ∑CHL varied in limits of 19.4–33.7 μg L–1 in the Upper Volga, 8.5–27.8 μg L–1 in the Middle Volga, and 5.2–11.3 μg L–1 in the Lower Volga. Photosynthetic activity coefficient (PhAC) varied mostly in limits of 0.12–0.59 with average of 0.22–0.38 and only in 2017 decreased to minimal <0.10 and average <0.20. The average PhAC values shows the normal physiological state of the phytoplankton of the Upper Volga during all periods of observation, occasional decrease of PhAC in the Middle Volga, and low photosynthetic activity in the Lower Volga. A decrease in the average ∑Chl and PhAC in 2017 was under cyclonic windy weather with a large amount of precipitation, low solar radiation, and large volume of flow. Trend towards a decrease in ∑CHL, like decrease in PhAC from the Upper Volga to the Lower Volga is explained by increasing in the flow rate and volume of runoff downstream the Volga River.

The effects of simulated acid rain (SAR) on the photosynthetic performance of subtropical coniferous species have not been thoroughly investigated. In this study, we treated two coniferous species, Pinus massoniana (PM) and Cunninghamia lanceolata (CL), with SAR and then analyzed photosynthetic activities via the simultaneous measurement of prompt fluorescence(PF), delayed fluorescence(DF), and modulated reflection at 820 nm(MR820). Following the low-pH SAR treatment, the I–P phase of the OJIP curves of PM and CL decreased significantly and then the K-band and L-band were detectable. The delayed fluorescence for both PM and CL decreased as the pH of the SAR solution decreased, with a more significant decrease in the I1 peak than in the I2 peak. According to the MR820 curve, the exposure to SAR stress inhibited the rapid decrease and slow increase in the MR820 transients of PM and CL. The gradients of the decreasing and increasing phases were lower for CL than for PM at pH 2.5. In addition, SAR decreased the light energy captured per unit area (ABS/CSm) and the quantum yield of electron transfer per unit area (ETO/CSm), but it increased the accumulation of QA−, thereby decreasing primary photochemical efficiency (TRO/CSm, φPO). These changes in photosystem II (PSII) resulted in a decrease in the maximum quantum yield of PSII (Fv/Fm) and the performance index (PIABS). Moreover, PSII was protected from thylakoid membrane photodamages through the increase in heat dissipation per unit area (DIO/CSm) in response to SAR. The increase in δRO as the pH of the SAR solution decreased was observed for PM, but not for CL. Considered together, the study findings suggest that SAR treatments can decrease chlorophyll contents and damage the OEC in PM and CL, which obstructs the transfer of electrons on the donor and acceptor sides of PSII. However, PM is better able to withstand SAR stress than CL, likely because of the activation of a protective mechanism (reflected by the change in δRO). Therefore, in coniferous forest areas severely affected by acid rain, CL may need to be protected more than PM.

Accurate estimation of chlorophyll content in wheat leaves can not only reflect its growth and nutritional status, but also provide a scientific basis for field management. In order to evaluate the potential of hyperspectral data to estimate the chlorophyll content of wheat leaves, this study focused on the leaves of wheat at the flag-picking stage, flowering stage, grain filling stage and maturity stage. Based on the framework of five vegetation indexes, the spectral index was con-structed by using the combination of 400-1000nm bands, and the correlation between the con-structed spectral index and the measured chlorophyll value was analyzed, and the optimal spectral index was screened by the correlation coefficient. Based on the optimal spectral index, polynomial regression, random forest, decision tree and artificial neural network were used to establish the estimation model of chlorophyll value, and the optimal model for estimating the chlorophyll value of wheat leaves was selected through model evaluation. The results showed that the five optimal spectral indices at the four growth stages were mainly composed of red band, red edge band and near-infrared band, and the five optimal spectral indices at the grain filling stage had the highest correlation with the chlorophyll value, and the absolute value of the cor-relation coefficient was greater than 0.73, the accuracy of the estimation model established in the four growth stages was different, and the estimation accuracy of the flag stage was the best, with R² and RMSE of 0.79 and 2.63, respectively. The above results show that hyperspectral data is suitable for estimating the chlorophyll value of wheat leaves, and the PR model of flag picking period can be used as the optimal model for estimating the chlorophyll value of wheat leaves.

Herein, we developed a highly sensitive and specific bimolecular fluorescence complementation (BiFC)-based influenza A virus (IAV) sensing system created by combining a galactose/glucose-binding protein (GGBP) with an N-terminal large domain (YN1-172) and a C-terminal small domain (YC173-239) of enhanced yellow fluorescence protein (eYFP). The GGBP-based BiFC reporter exhibits the fluorescence reconstitution as a result of conformational changes in GGBP when lactose, derived from 6’-silalyllactose used as a substrate for neuraminidase (NA), binds to GGBP in the presence of IAV. The system showed a linear dynamic range from 1 x 100 TCID50/mL to 1 x 107 TCID50/mL, with a detection limit of 4 x 101 TCID50/mL for IAV (H1N1), demonstrating ultra-high sensitivity. Our system exhibited fluorescence intensity enhancements in the presence of IAV, while displaying weak fluorescence signals when exposed to NA-deficient viruses such as RSV A, RSV B, adenovirus and rhinovirus, thereby indicating selective responses for IAV detection. Taken together, our system provides a simple, highly sensitive and specific IAV detection platform based on BiFC capable of detecting the ligand-induced protein conformational changes, obviating the need for virus culture or RNA extraction processes.

Induction heating (IH) technology is widely recognized and utilized in residential applications due to its high efficiency and safe operating characteristics. Resonant inverter circuits are widely used in IH systems because of their high efficiency and ability to perform soft-switching. Among the various resonant inverters used in IH systems, the single-switch quasi-resonant (SSQR) inverter topology is typically preferred for low-cost and low-output-power applications. Despite its cost advantage, the SSQR topology has a relatively narrow soft-switching range, which can be unstable depending on the electrical parameters of the load and the resonant converter circuit. Accurately determining the capacitance value of the resonant capacitor and the inductance value of the induction coil, which are the key circuit elements of the SSQR induction cooker, is crucial for designing a reliable, efficient, and durable cooking system. In other words, there exists a critical relationship between the resonant converter circuit parameters, load characteristics, and safe operating conditions. Additionally, when considering closed-loop control methods used for power control and safety, selecting appropriate resonant circuit elements becomes vital in ensuring both reliable and efficient operation. This paper focuses on a novel and simplified design method for the SSQR inverter utilized in household appliances. The proposed method and its advantages in terms of the safe operating area of the switch are theoretically investigated and verified through simulations and prototype circuits.

Background: In 2014 the World Health Organization (WHO) warned of an emerging world-wide crisis of antibiotic resistant microorganisms. In response, government and professional organizations recommended that health care systems adopt antimicrobial stewardship programs (ASPs). In the United States, the Centers for Medicare Services (CMS) mandated antimicrobial stewardship in the hospital inpatient setting. Effective January 1, 2020, the Joint Commission required ambulatory centers that prescribe antibiotics, such as wound centers, to institute an ASP. Chronic wounds often remain open for months, during which time patients may receive multiple courses of antibiotics and numerous antimicrobial topical treatments. The wound clinician plays an integral role in reducing antimicrobial resistance in the outpatient setting: antibiotics prescribed for skin and soft tissue infections are among the most common in an outpatient setting. One of the most challenging aspects of antimicrobial stewardship in treating chronic wounds is the inaccuracy of bacterial and infection diagnosis. Methods: Joint Commission lists five elements of performance (EP): (1) Identifying an antimicrobial stewardship leader, (2) establishing an annual antimicrobial stewardship goal, (3) implementing evidence-based practice guidelines related to the antimicrobial stewardship goal, (4) providing clinical staff with educational resources related to the antimicrobial stewardship goal, and (5) collecting, analyzing, and reporting data related to the antimicrobial stewardship goal. This article focuses on choosing and implementing an evidence-based ASP goal for 2020. Discussion: Clinical trials have demonstrated the ability of fluorescence imaging (MLiX) to detect clinically significant levels of bacteria in chronic wounds. Combined with clinical examination of signs and symptoms of infection, the MLiX procedure improves the clinician’s ability to diagnose infection and can guide antimicrobial use. In order to satisfy the elements of performance, the MLiX procedure was incorporated into the annual ASP goal for several wound care centers. Clinicians were educated on the fluorescence imaging device and guidelines were instituted. Collection of antimicrobial utilization data is underway.

We aimed at analyzing Chlorophyll-a and CDOM dynamics from field measurements and at assessing the potential of multispectral satellite data for retrieving water-quality parameters in three small surface reservoirs in the Brazilian semiarid region. More specifically, this work comprises i) analysis of Chl-a and trophic dynamics; ii) characterization of CDOM; iii) estimation of Chl-a and CDOM from OLI/Landsat-8 and RapidEye imagery. The monitoring lasted 20 months within a multi-year drought, which contributed to water-quality deterioration. Chl-a and trophic state analysis showed a highly eutrophic status for the perennial reservoir during the entire study period, while the non-perennial reservoirs ranged from oligotrophic to eutrophic, with changes associated with the first events of the rainy season. CDOM characterization suggests that the perennial reservoir is mostly influenced by autochthonous sources, while allochthonous sources dominate the non-perennial ones. Spectral-group classification assigned the perennial as CDOM-moderate and highly eutrophic reservoir, whereas the non-perennial ones were assigned as CDOM-rich and oligotrophic-dystrophic reservoirs. The remote sensing initiative was partially successful: the Chl-a was best modelled using RapidEye for the perennial; whereas CDOM performed best with Landsat-8 for non-perennial reservoirs. This investigation showed high potential for retrieving water quality parameters in dry areas with small reservoirs.

Experimental systems to simulate future elevated CO2 conditions in the field often have large, rapid fluctuations in CO2. To examine possible impacts of such fluctuations on photosynthesis, intact leaves of field grown plants of five species were exposed to two-minute cycles of CO2 between 400 and 800 mol mol-1 lasting a total of 10 minutes, with photosynthesis, stomatal conductance and PSII fluorescence measured at the end of each half-cycle, and also 10 minutes after the end of the cycling. Prior to the cyclic CO2 treatments, steady-state responses of leaf gas exchange and fluorescence to CO2 were determined. In four of the five species, in which stomatal conductance decreased with increasing CO2, the cyclic CO2 treatments reduced stomatal conductance. In those species, both photosynthesis and the photochemical efficiency of PSII were reduced at limiting internal CO2 levels, but not at saturating CO2. In the fifth species, there was no change in stomatal conductance with CO2, and no change in either photosynthesis or PSII efficiency at any CO2 level with CO2 cycling. It is concluded that in many, but not all, species fluctuations in CO2 may reduce photosynthesis at low CO2 partly by decreasing the photochemical efficiency of photosystem II, as well as by decreasing stomatal conductance.

In several mammalian species including humans, complex stimulation patterns such as cognitive challenge and physical exercise lead to improvements in organ function, organism health and performance, as well as possibly longer lifespans. The hypothesis is presented here that activity-dependent transcriptional programs, induced by these environmental stimuli, temporarily and lightly de-differentiate somatic cells such as neurons and muscle cells into a state that resembles functionally younger cells to allow cellular remodeling and adaptation of the organism to environmental change. This cellular adaptation program targets several process classes that are heavily implicated in aging, such as mitochondrial metabolism, cell-cell communication, intracellular signaling and epigenetic information processing and leads to functional improvements in these areas. I reverse engineer these activity-dependent gene programs, identify critical molecular nexus points such as CREB, MEF2 and cFos and speculate as to how one might leverage them to prevent and attenuate human aging-related decline of body function, enhance human performance and restore more youthful levels of function and morphology. The findings presented here can serve as a basis for the study and development of effective longevity efforts as the underlying gene programs could be used as markers for treatment success and as targets for therapy development.

Pertussis is a vaccine-preventable disease caused by the bacterium Bordetella pertussis. Over the past years, the incidence and mortality of pertussis increased significantly. A possible cause is the switch from whole cell to acellular pertussis vaccines, although other factors may also contribute. To develop future vaccines and improve current vaccination strategies, it is critical to understand factors influencing the generation of immunological memory. We applied high-dimensional flow cytometry to investigate changes in B cells in individuals of different ages and distinct priming backgrounds upon administration of an acellular pertussis booster vaccine. These findings were correlated to vaccine-specific plasma cells and serum Ig levels. Expansion and maturation of plasma cells 7 days post-vaccination was the most prominent cellular change in all age groups, and was most pronounced for more mature IgG1+ plasma cells. Cellular responses were stronger in individuals primed with whole cell vaccine than in individuals primed with acellular vaccine. Moreover, IgG1+ plasma cell expansion weakly correlated with Prn- and PT- specific serum IgG levels. Our study points at plasma cells as a potential early cellular marker of an immune response and contributes to understanding differences in immune responses between age groups and priming backgrounds.

Apurinic/apyrimidinic endonuclease 1 (APE1), also known as redox factor-1 (Ref-1), is a multifunctional protein which is widely existing in living organisms. It can specifically recognize and cleave the DNA in apurinic/apyrimidinic (AP) site in the base excision repair (BER) pathway, as well as regulate the expression of genes to activate some transcription factors. The abnormal ex-pression and disruptions in the biological functions of APE1 are linked to a number of diseases, including inflammation, immunodeficiency, and cancer. Hence, it is extremely desired to monitor the activity of APE1, acquiring a thorough understanding of the healing process of damaged DNA and making clinical diagnoses. Thanks to the advent of DNA nanotechnology, some nanodevices are used to image the activity of APE1 with great sensitivity and simplicity. In this review, we will summarize DNA nanotechnology-empowered fluorescence imaging in the past years for APE1 activity according to the types of DNA probe, which are classified into linear DNA probes, composite DNA nanomaterials and three-dimensional (3D) DNA nanostructures. We also highlight the future research directions in the field of APE1 activity imaging.

The synergic features and enhancing strategies for various photopolymerization systems are reviewed by kinetic schemes and the associated measurements. The important topics include: (i) photo crosslinking of corneas for the treatmnet of corneal deseases using UVA-light (365 nm) light and riboflavin as the photosensitizer; (ii) synergic effects by a dual-function enhancer in a 3-initiator system; (iii) synergic effects by a 3-initiator C/B/A system, having an electron-transfer and oxygen-mediated energy-transfer pathways; (iv) copper-complex (G1) photoredox catalyst in G1/Iod/NVK systems for free radiical (FRP) and cationic photopolymeriation (CP); (v) radical-mediated thiol-ene (TE) photopolymerizations; (vi) superbase photogenerator based-catalyzed thiol−acrylate Michael (TM) addition reaction; and the combined system of TE and TM usinghual wavelength; (vii) dual-wavelength (UV and blue) controlled photopolymerization confinement (PC); (viii) dual-wavelength (UV and red) selectively controlled 3D printing; and (ix) 3-wavelength selectively controlled in 3D printing and additive manufacturing (AM). With minimum mathematics, we present ( for the first time), the synergic features and enhancing strategies for various systems of multi-commponents, initiators, monomers, and under one- two- and there-wavelength light. Therefore, this Review provides not only the bridging between modeling and measurements, but also guidances for further experimantal stuides and new applications in 3D printings and additive manufacturing (AM), based on the innovative concepts (kinetics/schemes).

Chlorophyll a concentration (Chl) is a key variable to estimate primary production (PP) through ocean color remote sensing (OCRS). Accurate Chl estimate is crucial for better understanding of spatio-temporal trends of PP over recent decades as a consequence of climate change. However, a number of studies have reported that currently operational chlorophyll a algorithms perform poorly in the Arctic Ocean (AO), which is mainly caused by the interference of colored and detrital material (CDM) with the phytoplankton signal in the visible part of the spectrum. To determine how and to what extent that CDM would bias the estimation of Chl, we evaluated the performances of 8 currently available ocean color algorithms: OC4v6, OC3Mv6, OC3V, OC4L, OC4P, AO.emp, GSM01 and AO.GSM. Our results suggest that the empirical AO.emp algorithm performs the best overall, but for waters with high CDM (acdm(443) &gt; 0.067 m-1), which is of much interest in the Arctic, it is the two semi-analytical GSM models that show better performance. Besides, sensitivity analyses using an Arctic spectrally- and vertically-resolved primary production model further show that errors in Chl mostly propagate proportionally to PP estimates with 7% amplification at maximum. We aslo demonstrate that the higher level of CDM relative to Chl in the water column, the larger the bias would occur in both Chl and PP estimates. Although the AO.GSM overall best performs among algorithms tested in the present study, it tends to fail for a significant number of pixels (16.2% observed in the present study) particularly for waters with high CDM. Our results suggest that an algorithm that provides reasonable Chl estimates for a wide range of optically-complex Arctic waters is still required.

Stabilized melanocortin analog peptide ACTH(6-9)PGP (FRWGPGP) possess a wide range of neuroprotective activities. However, its mechanism of action remains poorly understood. In this paper, we studied the pro-proliferative and cytoprotective activity of the adrenocorticotropic hormone fragment 6-9 (FRWG) linked with the peptide Prolyl-Glycyl-Proline on the SH-SY5Y cells in the model of oxidative stress-related toxicity. The peptide dose-dependently protected cells from H2O2, tert-butyl hydroperoxide, and KCN. The mechanism of its action was the modu-lation of proliferation-related (NF-kB and Nrf-2) and antioxidant-related (HO-1, Nqo1, Gclc) genes and apoptosis decrease.

Weathering and erosion transport minerals and organics toward the sea or lake bottoms over geologic time. The finest solids are deposited in lower, less turbulent areas, such as lake bottoms and continental shelves. They sometimes stack up to thicknesses of kilometers, and begin compacting. These sediment sections are called shales, and as initially deposited in water, shales can have porosities up to 50-80{\%} water, As they are buried, many alteration products from oil to slate are produced due to overburden and temperature increasess, making them important to study. A preceeding paper \cite{1} showed that pressure solution is the primary mechanism for porosity reduction, with possible mechanical compaction at shallow depths. Without naming the mineral(s) involved, it postulated that the greater the product of the water and pore interfaces, the faster the reaction would proceed. This term is $ \varphi^{4m/3}(1-\varphi)^{4n/3}$ , where $\varphi$ is porosity and m and n are numbers close to unity. The large exponents, {\em 4/3}, recognize that the reaction occurs at the molecular scale at which the surfaces are rough. A second term, $\exp^{(-E/RT)}$ , indicates that the reaction is impeded by a quantum energy barrier, E, with diminished impeding power as increased available thermal energy, represented by the absolute temperature, T, becomes available at greater depths in the Earth. These two factors combine to allow porosity $\varphi$ to reduce with time, or equivalently for the fraction of solids, $(1-\varphi)$, to increase with time,$\left. \frac{\partial(ln(1-\varphi) ) }{\partial t } \right |_{\sigma} = (\varphi )^{4m/3}( 1-\varphi )^{4n/3}Ae^{-E/(RT)}$. { \em Here it is shown that this equation can cover quantitatively any actual deposition rates which may have been experienced by the six sections studied, the actual deposition rates being unknown for these cases. Hence a time-depth depositional history for any new shale section, known in detail, would allow determination of the parameters m, n, E and a lumped proportionality constant A. This was accomplished by showing that, for a wide range of depositional rates, r, the range of E for any of the studied sections is small compared to laboratory measurements of quartz solution\cite{2}, 24+-15kJ/mol. Results were obtained over this range of r's using the previously determined m and n, and porosity and temperature profiles. The presently existing porosity profiles necessarily incorporate any overpressure or underpressure conditions that may have existed in the past or currently, as the net difference between overburden and pore pressure is a primary driving force for pressure solution. $SiO_2$ usually comprises 20-50{\%} of shales. In conclusion, pressure solution of quartz can account for vertical compaction of shales quantitatively in the studied examples. Separately, a quasi-eqivalent method for discussing reduced porosities in Macron 2 versus Macron 1 as increased vertical stress, rather than additional horizontal stress, is illustrated. Experiments are suggested to clarify the pressure solution mechanism. The role of horizontal forces is discussed. From a global point of view, shale compaction by pressure solution is a quantified step in the cycling of continental rocks, beginning with rifting.

Extra virgin olive oil (EVOO) is the highest quality of olive oil and is characterized by highly beneficial nutritional properties. The large increase in both consumption and fraud, for example through adulteration, creates new challenges and an increasing demand for developing new quality assessment methodologies that are easier and cheaper to perform. As of today, the determination of olive oil quality is performed by producers through chemical analysis and organoleptic evaluation. The chemical analysis requires the advanced equipment and chemical knowledge of certified laboratories, and has therefore a limited accessibility. In this work a minimalist, portable and low-cost sensor is presented, which can perform olive oil quality assessment using fluorescence spectroscopy. The potential of the proposed technology is explored by analyzing several olive oils of different quality levels, EVOO, virgin olive oil (VOO), and lampante olive oil (LOO). The spectral data were analyzed using a large number of machine learning methods, including artificial neural networks. The analysis performed in this work demonstrates the possibility of performing classification of olive oil in the three mentioned classes with an accuracy of 100%. These results confirm that this minimalist low-cost sensor has the potential of substituting expensive and complex chemical analysis.

Low-frequency electromagnetic induction (EMI) is a non-invasive geophysical method that is based on the induction of electromagnetic (EM) waves into the subsurface to quantify changes in electrical conductivity. In this study we present an open (design details and software are accessible) and modular system for the collection of EMI data. The instrument proposed allows to adjust the separations between the transmitter and up to four receiving antennas as well as the acquisition frequency (in the range between 3 and 50 kHz) to permit measurements with variable depth of investigation. The sensor provides access to raw data and the software described in this study allows control of the signal processing chain. The design specifications permit apparent conductivity measurements in the range of between 1 mS/m and 1000 mS/m, with a resolution of 1.0 mS/m and with a sampling rate of up to 10 samples per second. The sensor allows for a synchronous acquisition of a time stamp and a location stamp for each data sample. The sensor has a mass of less than 5 kg, is portable and suitable for 1-person operation, provides 4 hours of operation time on one battery charge, and provides sufficient rigidity for practical field operations.

Severe cases of SARS-CoV-2 infection are characterized by an immune response that leads to the overproduction of pro-inflammatory cytokines, resulting in damage to the lungs and other organs. This remarkable increase in cytokines and other inflammatory molecules is primary caused by viral proteins, in particular ORF8, a unique accessory protein specific to SARS-CoV-2. In addition to its role in cytokine induction, ORF8 is attributed with various other functions, including its ability to evade type I interferon responses. Despite the evidence, the mechanisms through which ORF8 exerts these functions remains a subject of controversy. In this mini review, we discuss the multifaceted roles of ORF8 as a modulator of cytokine response, focusing on type I interferon and IL-6. We also discuss data from our studies indicating that ORF8 augments production of IL-6 induced by Poly(I:C) in human embryonic kidney (HEK)-293 and monocyte-derived dendritic cells (mono-DCs).

The authors of the paper have made an attempt to detect the fibre content and fibre spacing in a steel fibre reinforced concrete (SFRC) industrial floor. Two non-destructive testing (NDT) methods: an electromagnetic induction technique and a radar-based technique were applied. The first method allowed to detect the spacing in subsequent layers located in the thickness of the slab. The result of the second method was a 3D visualization of the detected fibre in the volume of concrete slab. The conducted tests showed aptitude and limitations of the applied methods in estimating fibre volume and spacing. The two techniques also allowed to locate the areas with relatively low fibre concentration which are very likely to be characterized by low mechanical properties.

In recent years, the utilization of machine learning algorithms and advancements in Unmanned Aerial Vehicle (UAV) technology have marked significant shifts in remote sensing practices. In particular, the integration of machine learning with physical models and their application in UAV-satellite data fusion have emerged as two prominent approaches for estimating vegetation biochemistry. This study evaluates the performance of five machine learning regression algorithms (MLRAs) for mapping crop canopy chlorophyll at the Kellogg Biological Station (KBS) in Michigan, USA, across three scenarios: (1) application to Landsat 7, RapidEye, and PlanetScope satellite images; (2) application to UAV-satellite data fusion; and (3) integration with the PROSAIL radiative transfer model (hybrid methods PROSAIL + MLRAs). The results indicate that the majority of the five MLRAs utilized in UAV-satellite data fusion perform better than the five PROSAIL + MLRAs. The general trend suggests that the integration of satellite data with UAV-derived information, including the normalized difference red-edge index (NDRE), canopy height model, and leaf area index (LAI), significantly enhances the performance of MLRAs. The UAV-RapidEye dataset exhibits the highest coefficient of determination (R2) and the lowest root-mean-square errors (RMSE) when employing kernel ridge regression (KRR) and Gaussian processes regression (GPR) (R2 = 0.89 and 0.89 and RMSE = 8.99 µg/cm2 and 9.65 µg/cm2, respectively). Similar performance is closely observed for the UAV-Landsat and UAV-PlanetScope datasets (R2 = 0.86 and 0.87 for KRR, respectively). For the hybrid models, maximum performance is attained with Landsat data using KRR and GPR (R2 = 0.77 and 0.51 and RMSE = 33.10 µg/cm2 and 42.91 µg/cm2, respectively), followed by R2 = 0.75 and RMSE = 39.78 µg/cm2 for PlanetScope data upon integrating partial least squares regression (PLSR) into the hybrid model. Across all hybrid models, RapidEye data yielded the most stable performance, with R2 ranging from 0.45 to 0.71 and RMSE ranging from 19.16 µg/cm2 to 33.07 µg/cm2. The study highlights the importance of synergizing UAV and satellite data which enables effective monitoring of canopy chlorophyll in small agricultural lands.

Berberine (BBR), as a natural isoquinoline alkaloid, has been demonstrated various pharmacological activities, and widely applied in the treatment of diseases. The quantitative analysis of BBR is important for its pharmacological researches and clinical applications. In the work, utilizing the specific interaction between BBR and triplex DNA, a sensitive and selective fluorescent detecting method was established with DNA-templated silver nanoclusters (DNA-AgNCs). After binding with the triplex structure in the template of DNA-AgNCs, BBR quenched the fluorescence of DNA-AgNCs and formed BBR-triplex complex with yellow-green fluorescence. The ratiometric fluorescence signal showed a linear relationship with BBR concentration in a range between 10 nM to 1000 nM, with a detect limit of 10 nM. Our method exhibited excellent sensitivity and selectivity, and it was further applied in BBR detection in real samples.

Fluorescence microscopic images of cells contain a large number of morphological features that are used as an unbiased source of quantitative information about cell status, through which researchers can extract quantitative information about cells and study the biological phenomena of cells through statistical and analytical analysis. As an important research object of phenotypic analysis, images have a great influence on the research results. Saturation artifacts present in the image result in a loss of grayscale information that does not reveal the true value of fluorescence intensity. From the perspective of data post-processing, we propose a two-stage cell image recovery model based on generative adversarial network to solve the problem of phenotypic feature loss caused by saturation artifacts. The model is capable of restoring large areas of missing phenotypic features. In the experiment, we adopt the strategy of progressive restore to improve the robustness of the training effect, and add the contextual attention structure to enhance the stability of the restore effect. We hope to use deep learning methods to mitigate the effects of saturation artifacts to reveal how chemical, genetic, and environmental factors affect cell state, providing an effective tool for studying the field of biological variability and improving image quality in analysis.

The theory of electron spin has been proposed for a century, but the study of quantum effects in biological molecules is still in its infancy. Chirality-induced spin selectivity (CISS) is a very modern theory that can explain many biochemical phenomena. In this paper, we propose a new theoretical model based on CISS theory and quantum chemistry theory, which can well explain the theoretical explanation of the chiral selectivity of chiral proteins. Moreover, this theory can predict the spin state of corresponding chiral molecules. Taking L-DOPA and AADC enzyme as examples, this theoretical model solves the theoretical explanation of AADC enzyme's chiral catalysis selectivity problem and successfully predicts the spin state of L-DOPA and D-DOPA's valence electrons.

Asphaltene precipitation and deposition pose significant operational challenges in both reservoirs and surface facilities by inducing formation damage. To understand the kinetics involved in asphaltene particle nucleation, growth, and aggregation, this study employed confocal microscopy and centrifuge-based methods under a unified set of experimental parameters. The acquired time-resolved particle size images were analyzed using MIPAR image processing software, while asphaltene mass yield was quantitatively evaluated through centrifugation. Experimental conditions were varied to study the effects of heptane concentration, asphaltene concentration, and shear rate. Notably, this investigation introduces, for the first time, the parameter of particle count as an additional variable influencing asphaltene mass production. This study aims to discern how particle count correlates with asphaltene mass yield over time. Results indicate that the minimum mean particle diameter was observed to be 2 microns, which progressively grew up to 80 microns. The mean particle diameter exhibited a positive correlation with both asphaltene concentration and shear rate, whereas an inverse correlation was seen with heptane concentration. Furthermore, the asphaltene mass yield was found to increase with greater asphaltene and heptane concentrations, as well as with higher shear rates. The relationship between mean particle diameter and mass yield was found to be nonlinear. In the early stages, a higher prevalence of small particles contributed to a greater total particle count, while at later stages, particle aggregation led to the formation of larger particles that influenced the overall asphaltene mass. The insights gained from understanding the relationship between particle diameter, count, and mass yield are crucial for advancing the fundamental science of asphaltene precipitation and deposition. These findings may also guide future research that relies solely on particle counts for assessing asphaltene deposition.

In this study, 12 organic waste materials were subjected to TG/DTG thermogravimetric analysis and DSC calorimetric analysis. These analyses provided basic information about thermochemical transformations and degradation rates during organic waste pyrolysis. Waste materials were chosen to cover the most abundant waste that can be found in the municipal solid waste stream. Based on TG results, kinetic parameters according to Coats–Redfern method were determined. The pyrolysis activation energy was the highest for cotton 134.5 kJ∙(mol∙K)-1 and the lowest for leather 25.2 kJ∙(mol∙K)-1. The DSC analysis showed number of transformations occurred during pyrolysis for each material. For each transformation, normalized energy required for transformation, or released during transformation were determined and then summarized to present energy balance. The study found that only for three waste materials: PET (-220.1 J⸱g-1), leather (-66.9 J⸱g-1), and chicken meat (-130.3 J⸱g-1) energy balance was negative, while the highest positive balance value was found for potato peelings (367.8 J⸱g-1). The obtained results may be applied for the modelling of energy and mass balance of municipal solid waste pyrolysis.

The reaction kinetics of burnt lime (CaO) in contact with sea water has been elucidated and compared to its behaviour in fresh water. In the first minutes of contact between burnt lime and water, it "slaked" as CaO reacted with water to yield calcium hydroxide (Ca(OH)2). Subsequently, calcium hydroxide reacted with magnesium, sulphate and carbonate from the sea water to yield magnesium hydroxide (Mg(OH)2), calcium sulphate dihydrate (gypsum, CaSO4·2H2O) and calcium carbonate (CaCO3), respectively. In a closed system of 1% CaO in natural sea water (where the supply of sulphate, magnesium and carbonate is limited), more than 90% reacted within the first 5 hours. It is foreseen that in an open system, like a marine fjord, it will react even faster. The pH 8 of sea water close to the CaO particle surface will immediately increase to a theoretical value of about 12.5 but will, in an open system with large excess of sea water, rapidly fall back to pH 10.5 being equilibrium pH of magnesium hydroxide. This is further reduced to < 9 due to the common ion effect of dissolved magnesium in sea water and then be diluted to the sea water background pH, about 8. Field test dosing CaO particles to sea water showed that the pH of water between the particles stayed around 8.

Polyanilines are a class of conductive polymers that have attracted significant interest in the field of organic electronics due to their unique properties. In this article, the fluorescence spectroscopy and photovoltaic properties of polyaniline-based thin films and copolymers are investigated. The study focuses on understanding the relationship between the composition and structure of polyanilines and their optical and electrical properties. The article discusses the results of experiments on the photoluminescent properties of S1-S9 copolymers in a DMSO solution and of thin-film photoresistors based on polyanilines. The findings reveal that the photovoltaic properties of the thin films depend on the conditions of their fabrication and their surface morphology. The solubility of polyanilines is excellent, making the production of electronic components compatible with modern printing technologies in organic electronics. The work also points out that the photoconductivity of polyanilines can be improved by incorporation of additional molecular groups into the polymer matrix. Overall, this study sheds light on the potential of polyanilines as promising materials for organic electronics and provides insights into how their properties can be optimized for specific applications.