This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

A sustainable low cost activated carbon substitute was produced based on pretreated lignocellulosic biomass, especially spruce sawdust. A harmful liquid waste, desalination brine was used for the treatment of a solid wood industry waste, spruce sawdust. This approach is in the circular economy theory and aims to the decarbonization of the economy. The pretreated sawdust was tested as an adsorbent appropriate for the removal of a commonly used pollutant, methylene blue, from industrial wastewater. The adsorption capacity of the pretreated material was found to increased four times comparing to the untreated one in the case that the Freundlich equation was fitted to the isotherms’ data. The treatment experimental conditions with desalination brine that gave maximum adsorption capacity correspond to 1.97 combined severity factor in logarithmic form value. The same adsorption capacity was found to increase five to six times comparing to the untreated spruce sawdust in the case that the Langmuir isotherm model was applied at the same data. Moreover, kinetic experiment was cried out as regards the methylene blue adsorption process. The desalination brine pretreated sawdust adsorption capacity increased 1.4 times comparing to the untreated one, in the case of the Lagergren kinetic equation fitting. Furthermore, the adsorption capacity of the same material was increased 1.6 times when the second order kinetic model was applied to the same data. Industrial scale applications can be based on the kinetic data findings as they have to do with a very shorter adsorption period comparing to the isotherm data.

Large-scale hydrological modeling in China is challenging given the sparse meteorological stations and large uncertainties associated with atmospheric forcing data.Here we introduce the development and use of the China Meteorological Assimilation Driving Datasets for the SWAT model (CMADS) in the Heihe River Basin(HRB) for improving hydrologic modeling, by leveraging the datasets from the China Meteorological Administration Land Data Assimilation System (CLDAS)(including climate data from nearly 40000 area encryption stations, 2700 national automatic weather stations, FengYun (FY) 2 satellite and radar stations). CMADS uses the Space Time Multiscale Analysis System (STMAS) to fuse data based on ECWMF ambient field and ensure data accuracy. In addition, compared with CLDAS, CMADS includes relative humidity and climate data of varied resolutions to drive hydrological models such as the Soil and Water Assessment Tool (SWAT) model. Here, we compared climate data from CMADS, Climate Forecast System Reanalysis (CFSR) and traditional weather station (TWS) climate forcing data and evaluatedtheir applicability for driving large scale hydrologic modeling with SWAT. In general, CMADS has higher accuracy than CFRS when evaluated against observations at TWS; CMADS also provides spatially continuous climate field to drive distributed hydrologic models, which is an important advantage over TWS climate data, particular in regions with sparse weather stations. Therefore, SWAT model simulations driven with CMADS and TWS achieved similar performances in terms of monthly and daily stream flow simulations, and both of them outperformed CFRS. For example, for the three hydrological stations (Ying Luoxia, Qilian Mountain, and ZhaMasheke) in the HRB at the monthly and daily Nash-Sutcliffe efficiency ranges of 0.75-0.95 and 0.58-0.78, respectively, which are much higher than corresponding efficiency statistics achieved with CFSR (monthly: 0.32-0.49 and daily: 0.26 – 0.45). The CMADS dataset is available free of charge and is expected to a valuable addition to the existing climate reanalysis datasets for deriving distributed hydrologic modeling in China and other countries in East Asia.

A series of novel substituted isoxazolidine derivatives was synthesized through 1,3-dipolar cycloaddition reactions of α-aryl-N-methyl nitrones with various ethylene moieties, resulting in the formation of isoxazolidine derivatives. The structures of the synthesized compounds were characterized using spectroscopic methods. The [3+2] cycloaddition (32CA) reactions of α-aryl-N-methyl nitrones with diverse ethylene substituents were computed employing Density Functional Theory (DFT) at the B3LYP/6–31G(d) level, upgrading bond parameters. An investigation of the electron localization function (ELF) unveiled the zwitterionic nature of α-aryl-N-methyl nitrones, devoid of pseudoradical or carbenoid centers. Utilization of CDFT indices enabled the prediction of global electronic flux from the strongly nucleophilic α-aryl-N-methyl nitrones to the varied electrophilic ethylene functionalities. Molecular docking and molecular dynamics simulations were conducted on the isoxazolidine derivatives against the EGFR receptor (PDB: 4ZAU). In silico assessment of the synthesized isoxazolidines involved molecular docking, wherein the compound with the highest docking score was subjected to molecular dynamics simulations. Compound 11a, out of the thirty isoxazolidine derivatives, displayed the most substantial binding energy, yielding a g score of -6.57 kcal/mol. These observations highlighted the functional role of amide NH2 and NO2 in the binding process with the target protein, influencing its activity. Furthermore, prediction of ADME drug-likeness properties was performed to identify a suitable candidate.

Aurora kinase A (AURKA) is a normal cell proliferation-inducing enzyme encoded by AURKA gene, with over-expression observed in different types of malignancies. Hence, the goal is to find potential inhibitors against AURKA. In this study, molecular docking, Standard Precision and Extra Precision methods were employed. After the docking study, the ligands showed an extremely low binding score which suggested very high binding affinity of the ligands. Furthermore, Quantum polarized ligand docking (QPLD) was performed to predict the binding status of the molecules. Based on the binding affinity, the top four compounds were chosen for further analysis. The docked complexes were further analyzed in explicit water conditions using 100 ns molecular dynamics simulations and binding free energy calculation. Then, density functional theory (DFT) calculation was used to calculate the molecular properties of the molecules. Finally, systems biology experiments validated the molecular docking and molecular dynamics simulation studies and indicated that quercetin, kaempferol, luteolin and rutin could inhibit the AURKA. The results show that, these four molecules have high binding affinity to the AURKA and significant interactions (LEU139, GLU211and ALA213) were also identified with the hinge region of Aurora kinase A. Thus, LEU139, GLU211, and ALA213 were identified as the crucial protein mechanisms.

Crop production in Afghanistan suffers from limited phosphorus (P) availability, which severely hinders national agriculture sustainability. This present study hypothesized that deep fertilizer placement could significantly enhance uptake of immobile P and thus tissue P accumulation and crop yield. A two-year pot experiment growing two maize (Zea mays) hybrid cultivars (Xida-789 and Xida-211) was therefore conducted to test these hypotheses under three contrasting fertilizer placement methods (broadcast, side band, and deep band). In doing so, P concentrations in both maize tissues and soils were compared at 45, 60, and 115 days after sowing (DAS) under nine combinations of nitrogen (N) and P fertilizer rates (kg ha-1: N112P45, N112P60, N112P75, N150P45, N150P60, N150P75, N187P45, N187P60, N187P75). Results have shown that deep band placement significantly increased P uptake efficiency, leading to greater P concentration and accumulation in maize tissues compared to other two fertilization methods. This improved P uptake was attributed to several factors associated with deep placement, including reduced P fixation, enhanced root access to P, and moisture availability for P uptake. Additionally, deep band placement combined with higher N application rates (N187 and N150) further enhanced plant P uptake by promoting P availability and utilization mechanisms. Deep band placement also resulted in significantly higher total soil P, Olsen-P, and P use efficiency than broadcast and side band methods, indicating a more efficient P fertilization strategy for maize that can improve growth and yield. This present study also found positive correlations between P concentration in plant organs and soil Olsen-P, highlighting the importance of adequate soil P levels for optimal plant growth. Overall, our results have showed that deep band fertilizer placement emerged as a superior strategy for enhancing P uptake efficiency, utilization, and maize productivity compared to broadcast and side band placement. This approach can potentially optimize P fertilizer utilization, improve maize growth and yield, while minimizing environmental P losses associated with broadcast applications.

Eruca sativa is a commonly used edible plant in Italian cuisine. E. sativa 70% ethanol extract (ES) was fractionated with five organic solvents. Ethyl acetate fraction(EEA) had the highest antioxidant activity, which was correlated with the total polyphenol and flavonoid content. ES and EEA acted as PPAR-α ligands by PPAR-α competitive binding assay. EEA significantly increased cornified envelope formation as a keratinocyte terminal differentiation marker in HaCaT cells. Further, it significantly reduced nitric oxide and pro-inflammatory cytokines in lipopolysaccharide-stimulated RAW 264.7 cells. The main flavonol forms detected in high amounts from EEA are mono-, and di-glycoside of each aglycone. Flavonol mono-glycosides were shown to be a potent PPAR-α ligand using molecular docking simulation and showed the inhibition of nitric oxide. These results suggest that E. sativa is suitable for use in improving skin barrier function and inflammation in skin disorders, such as atopic dermatitis.

A derivative series of 3,4-dimethoxy-β-nitrostyrene were synthesized and identified including new compound 6. The effect of antimicrobial activity of 3,4-alkyloxy modification of β-nitrostyrene was investigated. A molecular docking was also performed to obtain information about their interactions with Protein Tyrosine Phosphatase 1B (PTP1B). PTP1B containing cysteine 215 and arginine 221 as essential active residues plays a key role in signaling pathways that regulate various cell functions of microorganisms, which also act as negative regulator in signaling pathways of insulin that are involved in type 2 diabetes and other metabolic diseases. Compound 5 and 6 were the most potent as fragment of PTP1B inhibitor based on molecular docking, but compound 5 was more effective against Candida albicans. These compounds interact with serine 216 and arginine 221 residues. However, further research is needed to investigate their potential medicinal use.

Conditions under which compositions of component systems form a well-defined system-of-systems here are formulated at a fundamental level. Statement of what defines a well-defined composition and sufficient conditions guaranteeing such a result offers insight into exemplars that can be found in special cases such as differential equation and discrete event systems. For any given global state of a composition, two requirements can be stated informally as: 1) the system can leave this state, i.e., there is at least one trajectory defined that starts from the state, and 2) the trajectory evolves over time without getting stuck at a point in time. Considered for every global state, these conditions determine whether the resultant is a well-defined system and if so, whether it is non-deterministic or deterministic. We formulate these questions within the framework of iterative specifications for mathematical system models that are shown to be behaviorally equivalent to the Discrete Event System Specification (DEVS) formalism. This formalization supports definitions and proofs of the afore-mentioned conditions. Implications are drawn at the fundamental level of existence where the emergence of a system from an assemblage of components can be characterized. We focus on systems with feedback coupling where existence and uniqueness of solutions is problematic.

The details of antigen-antibody interactions and the identification of epitopes are critical for the development of monoclonal antibody drugs. Ab42 is a native human-derived anti-CFH monoclonal antibody. In this study, the interaction between antigen pCFH and antibody (Ab42) was theoretically demonstrated by molecular docking and MD simulation, combined with free energy calculation and computational alanine scanning (CAS), and key amino acids and epitopes were identified. Experimental alanine scanning (EAS) was then carried out to verify the results of the calculation, and our results indicated that Ab42 antibody forms hydrogen bonds and interacts hydrophobically with pCFH through the Tyr315, Ser100, Gly33, and Tyr53 residues on its CDR, while the main pCFH epitopes are located at the six sites of Pro441, Ile442, Asp443, Asn444, Ile447, and Thr448. In conclusion, this study has explored the mechanism of antigen-antibody interaction from both theoretical and experimental aspects, and our results have important theoretical significance for the design and development of relevant antibody drugs.

Histone Lysine Specific Demethylase 1 (LSD1) is overexpressed in many cancers and become a new target for anticancer drugs. In recent years, the small molecule inhibitors with various structures targeting LSD1 have been reported. Here we report the binding interaction modes of a series of thieno[3,2-b]pyrrole-5-carboxamides LSD1 inhibitors using molecular docking, three dimensional quantitative structure-activity relationship (3D-QSAR). Comparative molecular field analysis (CoMFA q²=0.783, r²=0.944, r²_pred=0.851) and Comparative molecular similarity indices analysis (CoMSIA q²=0.728, r²=0.982, r²_pred=0.814) were used to establish 3D-QSAR models, which had good verification and prediction capabilities. Based on the contour maps and the information of molecular docking, 8 novel small molecules were designed in silico, among which compounds D4, D5 and D8 with high predictive activity were subjected to further molecular dynamics simulations (MD), and their possible binding modes were explored. It was found that Asn535 plays a crucial role in stabilizing the inhibitors. Furthermore, the ADME and bioavailability prediction for D4, D5 and D8 were carried out. The results would provide valuable guidance for designing new reversible LSD1 inhibitors in the future.

The apicomplexan parasite, Sarcocystis neurona causes the degenerative neurological equine protozoal myeloencephalitis (EPM) disease of horses. Due to its host range expansion, S. neurona is an emerging threat that requires close monitoring. In apicomplexans, protein kinases (PKs) have been implicated in a myriad of critical functions such as host cell invasion, cell cycle progression and host immune responses evasion. Here, we used various bioinformatics methods to define the kinome of S. neurona and phylogenetic relatedness of its PKs to other apicomplexans. Further, three-dimensional (3D) homology models for selected S. neurona putative PKs were constructed and evaluated for inhibitor docking. We identified 92 putative PKs clustering within the AGC, CAMK, CK1, CMGC, STE, TKL, aPK and OPK groups. Although containing the universally conserved PKA (AGC group), S. neurona kinome was devoid of PKB and PKC, but contained the six apicomplexan conserved CDPKs (CAMK group). The OPK group was represented by ROPKs 19A, 27, 30, 33, 35 and 37, but was devoid of the virulence-associated ROPKs 5, 6, 18 and 38. Two out of the three S. neurona CK1 enzymes had high sequence similarities to T. gondii TgCK1-α and TgCK1-β and the Plasmodium PfCK1. Docking of four inhibitors onto homology models of putative ROP27 and PKA indicated that inhibition of S. neurona PKs is feasible, but needs to be experimentally tested. The essentiality of apicomplexan PKs makes the elucidation of S. neurona kinome a key milestone for development of novel therapeutics for EPM.

Long COVID is the collective term used to describe the persistence of symptoms in individuals who have recovered from SARS-CoV-2 infection. Some people who have healed from COVID-19 continue to experience new or persistent symptoms that last for weeks or months. While Long COVID is becoming more widely recognized, its fundamental causes and effective therapies remain largely unclear. This study aims to explore the potential of phytochemical medications as a cutting-edge therapeutic strategy for treating Long COVID, also known as post-acute sequelae of SARS-CoV-2 infection (PASC).G protein-coupled receptors (GPCRs), which play a critical role in cell signaling, were the focus of this study. GPCRs are known to be involved in immunological and inflammatory responses and are considered potential targets for Long COVID therapy. The GPCRs examined included chemokine receptors, serotonin receptors, adrenergic receptors, and histamine receptors. The docking results demonstrated high binding affinity between phytochemical drug structures and these receptors for most drug-receptor combinations.The study consists of three main parts. First, data on receptors and drugs were retrieved from the Protein Data Bank (PDB) and PubChem, respectively. The receptors selected are those predicted to be linked to Long COVID. The structure of the drugs was converted from SDF to PDB format using OpenBabel from ChemInfo. Docking studies were performed to assess the binding affinity between the drugs (ligands) and their respective receptors (binding sites) using iGemDock v2.1.In conclusion, the findings of this study could have significant implications for the development of alternative therapies for Long COVID.

Based on screening in computational biology and biological in vitro assays, five natural products isolated from extracts of the herbal medicine toad skin, such as cinobufagin (CBFi), bufalin (BFi), arenobufagin (ABFi), telocinobufagin (TBFi), bufotalin (BFTi), were subjected to molecular docking calculations with the use of SARS-CoV-2 main protease (PDB 6LU7 and 7BTF) and top-scoring ligand-receptor complexes were obtained. The results showed that the binding energy of ABFi to the 3CL protein was -17.044kcal/mol, which was higher than CBFi and TBFi. However, the binding energy of ABFi to the RdRp protease was -23.250 kcal/mol, which was much lower than that of CBFi and TBFi, EVEN lower than that of ABFi to the 3CL protein. ABFi also has polar interactions with amino acids such as Glu811, Ser814, Ser681 and Thr680 of RdRp enzyme. The results revealed that ABFi had a moderate inhibitory effect on the cell proliferation of SARS-CoV-2 in vitro, with an inhibition rate of 61.12%, even weaker than Remdesivir. This new discovery provides us with new ideas for in-depth studies on the development of natural products with this class of structural generalizations as inhibitors of SARS-CoV-2, and provides an experimental basis for the next step of mechanistic studies.

Histones are keys to many epigenetic events and their complexes have therapeutic and diagnostic importance. The determination of the structures of histone complexes is fundamental in the design of new drugs. Computational molecular docking is widely used for the prediction of target-ligand complexes. Large, linear peptides like the tail regions of histones are challenging ligands for docking due to their large conformational flexibility, extensive hydration, and weak interactions with the shallow binding pockets of their reader proteins. Thus, fast docking methods often fail to produce complex structures of such peptide ligands at a level appropriate for drug design. To answer this challenge, and improve the structural quality of the docked complexes, post-docking refinement has been applied using various molecular dynamics (MD) approaches. However, a final consensus has not been reached on the desired MD refinement protocol. In the present study, MD refinement strategies were systematically explored on a set of problematic complexes of histone peptide ligands with relatively large errors in their docked geometries. Six protocols were compared that differ in their MD simulation parameters. In all cases, pre-MD hydration of the complex interface regions was applied to avoid the unwanted presence of empty cavities. The best-performing protocol achieved a median of 32 % improvement over the docked structures in terms of the change of root mean squared deviations from the experimental references. The influence of structural factors and explicit hydration on the performance of post-docking MD refinements was also discussed to help their implementation in future methods and applications.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

Using numerical simulation method, combined with the pre-branch material characteristics of the measurement results, based on the LS-DYNA software to simulate the branch crushing process, the analysis found that not only the existence of the cutter cutting in the branch destruction process, there is also the cutting of the opposing surface of the bending fracture, with the increase in the speed of the knife rollers, the cutter cutting resistance increases, the cutting resistance reaches 2690 N when the cutter at 2500 r/min, the cutter cutting resistance is the smallest in the cutting simulation at the blade angle of 55°, the blade angle is more suitable for the cutting of the branch. In the cutting simulation under different cutting edge angles, the cutting resistance of the tool is the smallest when the edge angle is 55°, which is 1860 N. This edge angle is more suitable for branch crushing and cutting. Using Fluent software to analyse the airflow characteristics of the crushing device, it was found that with the increase of the knife roller speed, the inlet flow and negative pressure of the crushing chamber are increasing, the speed of 2500 r/min, the inlet flow and negative pressure were 1.92 kg/s and 37.16 Pa, which will be conducive to the feeding of branches, but the speed is too high and it will also lead to the enhancement of the vortex of part of the area in the crushing device, which will affect the feeding of branches and the throwing of the crushed material. affect the feeding of branches and the throwing out of crushed materials, and finally determined the speed range of the crushing knife roller is 1800 ~ 2220 r/min. Based on ANSYS/Model module modal analysis of the crushing knife roller, the knife roller of the first six orders of the intrinsic frequency and vibration pattern, crushing knife roller of the lowest order of the modal intrinsic frequency of 137.42 Hz, much larger than the crushing knife roller operating frequency of 37 Hz, the machine will not resonate during operation.

The origin of a product, consumer familiarity, and purchasing identity are factors that affect perception of cheese consumption. The present study aims at identifying consumers’ conceptualizations and attitudes towards local Greek cheeses of the North-Aegean Sea islands, such as Ladotyri, Graviera, Kasseri, Kaskavali, Melichloro, and Kalathaki, some of which have a Protected Designation of Origin (PDO) status, as opposed to cheeses of non-Greek origin, such as Cheddar, Regatto, and Gouda. Sensory and emotional attributes of local, local PDO, and imported cheeses, and drivers associated with consumers’ choice and acceptance above and beyond their sensory attributes were studied, using three methods: a) Flash Profile to gain insight into the sensory positioning of products and description of samples, b) qualitative analysis of focus groups to pinpoint consumer knowledge, preference, and consumption criteria, and c) a new methodology for natural language processing and sentiment analysis of social media posts to determine consumer conceptualizations. Social media posts have proven to be a valuable source of linguistic and cultural data for cheeses. Local cheeses, including PDO products, were found to be linked to village life and family gatherings, home, tradition, and childhood memories, with saltiness and hardness being their main sensory attributes. Imported cheeses were linked to fast food, pizza, and snacking, with elasticity and gumminess as prominent sensory qualities. The main criterion of purchase was intended usage and versatility, taste and texture, price, and familiarity. The findings provide key sensory attributes, information about consumer purchasing criteria, and relevant vocabulary for the promotion of cheeses as agri-food and gastronomic identity key products.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

The development of virtual models has recently been generalized in the field of complex mechatronic product design. Virtual models have various advantages such as: the systemic design approach, most often parametric, the implementation of extreme, expensive, and perhaps risky scenarios for the operation of the designed product, the testing of a large number of variants, etc. The main contribution of the paper consists of the development of an interface family called DeSeRoI (Dedicated Serial Robot Interface). Each member of the interface family integrates Simulink libraries and is created by the programmer in accordance with user requests. It follows that the interfaces composing the DeSeRoI family can have different levels of complexity depending on user needs and constraints. We are implementing a MATLAB-based application with user-provided configuration for serial robots in order to automatically visualize the kinematics data and simulation. Within MATLAB, two scripts are created responsible for generating Simulink models that compute the kinematics problem. One of the scripts (Main) saves information about the configuration of the robot and the other one (Generates_Simulink_Models) computes the kinematics problem. Different types of functions (software module) have been developed. Using these functions, the Simulink models result as modular entities. The automated approach eases user’s interaction and understanding of serial robots’ kinematics by performing the simulation procedure in a shorter amount of time and with higher efficiency, assuring a precise outcome despite the chosen parameters.

This study examines geothermal energy extraction potential from the basement rock within the Denver-Julesburg (DJ) Basin, focusing on flow performance and heat extraction efficiency of different geothermal well configurations. It specifically compares U-Shaped, V-Shaped, Inclined V-Shaped, and Pipe-in-Pipe configurations against Enhanced Geothermal Systems (EGS) setups. Through numerical modeling, we evaluated the thermal behavior of these systems under various operational scenarios and fracture conditions. Results suggest that while closed-loop systems offer moderate temperature increases, EGS configurations show substantial potential for high-temperature extraction. This underscores the importance of evaluating well configurations in complex geological settings like the DJ Basin. The insights from this study aid in strategic geothermal energy planning and development, marking significant advancements in geothermal technology and setting a foundation for future explorations and optimizations.

Driven by the growing interest of the scientific community and the proliferation of research in this field, cranial implants have seen significant advancements in recent years regarding design techniques, structural optimisation, appropriate material selection and fixation system method. Custom implants not only enhance aesthetics and functionality but are also crucial for achieving proper biological integration and optimal blood irrigation, critical aspects in bone regeneration and tissue health. This research aims to optimize the properties of implants designed from triply periodic minimal surface structures. The gyroid architecture is employed for its balance between mechanical and biological properties. Experimental samples were designed varying three parameters of the surface model: cell size, isovalue and shape factor. Computational simulation tools were used for determining the relationship between those parameters and the response variables: the surface area, permeability, porosity and Young modulus. These tools include computer aided design, finite element method and computational fluid dynamics. With the simulated values, the corresponding regression models were fitted. Using the NSGA-II, a multi-objective optimisation was carried out, finding the Pareto set which includes surface area and permeability as targets, and fulfil the constraints related with the porosity and Young modulus. From these non-dominated solutions, the most convenient for a given application was chosen, and an optimal implant was designed, from a patient computed tomography scan. An implant prototype was additively manufactured for validating the proposed approach.

Ten new Schiff bases, including thiocarbohydrazone derivatives (1–10), were synthesized using an efficient, uncomplicated, and environmentally friendly approach using the reaction of alkyl-substituted aldehydes. The thiocarbohydrazones that were obtained were derived from o-phthalaldehyde. The chemical structures of the compounds were identified by the utilization of UV-Vis spectroscopy, Fourier transform infrared (FT-IR), ¹H nuclear magnetic resonance (¹H NMR), ¹³C nuclear magnetic resonance (¹³C NMR), and elemental analysis methods. The thermal stability of thiocarbohydrazones was examined using thermogravimetric analysis (TGA-DSC). Investigations were conducted on urease inhibition tests, pharmacokinetic property research, and molecular docking. The collection of samples with the urease enzyme revealed significant molecular docking findings, with MolDock scores ranging from -153 to -189. The compounds have the potential to be effective drug candidates for treating certain diseases, as indicated by the consistent results of molecular docking, urease inhibition tests, and pharmacokinetic characteristics investigations.

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

In this paper we report a new development on the numerical model for aluminum-steam combustion. This model is based on diffusion flame of continuum regime and the thermal equilibrium between the particle and the flow field, which can be used to calculate the aluminum particle combustion model for two phase calculation conditions. The model prediction is in good agreement with the experimental data. A new type of vortex combustor was proposed for the combustion of aluminum and steam, and the mathematical model of the two phase reacting flow with in this combustor was established. The turbulence effects are modeled using the Reynolds Stress Model (RSM) with Linear Pressure-Strain approach, and the Eddy-Dissipation model is used to simulate the gas phase combustion. Aluminum particles are injected into the vortex combustor and form a swirling flow around the chamber and their trajectories are traced using the Discrete Phase Model (DPM). The simulation results show that the vortex combustor can achieve high efficient combustion of aluminum and steam. The influencing factors, such as the eccentric distance of the inlet of aluminum particles, particle size and steam inlet diameter, etc., are studied. The work described in this paper represents an attempt to the design of a vortex combustor in order to increase aluminum combustion efficiency.

The majority of existing numerical simulations of the effect of bridge piers on water movement are based on a limited number of bridge piers at a laboratory scale. Furthermore, some 2D numerical simulations for actual bridge projects have deficiencies, including the use of overly large mesh sizes and an inadequate treatment of bridge piers. In this study, we compare three methods of structural mesh encryption, suspension mesh, and nonstructural mesh based on Delft3D, and apply the optimization scheme to a real bridge project. It is demonstrated that optimal results can be achieved by utilising a grid size comparable to the pier diameter (Dp) in the region away from the piers. In the vicinity of the piers, the grid cell size should be no larger than 1/9 Dp. The suspended grid technique (DD Boundary) can yield results consistent with those obtained using a full-area high-resolution grid, provided that the total number of grids can be reduced and the computational time is considerably reduced. In this study, the unstructured mesh (Deflt3D Flexible Mesh) scheme was unable to capture the oscillations of the wake flow behind the bridge piers. However, the application of the optimized scheme in bridge engineering has demonstrated its practical value. The findings of this study on mesh resolution and suspension mesh scheme can be applied to the Delft3D software and are also useful for other numerical simulation work.

The control of the fine particle emission from the coal-fired power plants has been a big challenge in china. Either the conventional electrostatic precipitator or the fabric filter has some shortages. The electrostatic precipitator is hard to keep high efficiency for the submicron particles. The fabric filter could keep high efficiency but with very high pressure drop. One solution is to combine them together. Several types of hybrid particle collectors (HPC) combining the electrostatic precipitator and the fabric filter together have been developed and applied in a number of projects in China. In recent years, numerical simulation technology has been widely used in the design of the collectors. In this paper, an unsteady numerical model is used to investigate the particle deposition characteristics in a scale hybrid collector. The fluid field is modeled by using incompressible Navier-Stokes equations with the RNG turbulence equations. The corona discharge is solved by using a finite volume method. The particle charging is modeled by using a filed-diffusing combined model. And an unsteady cake formation model is used to simulate the filtration process.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

Shear dynamics simulation under extreme pressure was used to optimise the composition of ester-based lubricant base oil and extreme pressure additives. As a result, the ester-based lubricant in the weak-gel drilling fluid achieves reduction and increases the efficiency in drilling construction, and the field operation efficiency improves. The results of base oil lubrication simulation show that three base oils, namely, methyl oleate, ethyl oleate and butyl oleate, can be stably adsorbed on the surface layer of the shear surface. Methyl oleate has the lowest system temperature after shear stabilisation and has a high load-bearing capacity. The shear stress of methyl oleate decreases by changing the initial shear temperature and speed. It increases by 6.36 MPa when the speed increases from 10 m/s to 30 m/s. At this time, the shear stress of butyl oleate increases by 10.11 MPa. The results of the four-ball friction experiments show that the radius of the abrasion spot of methyl oleate is 179.83 μm, which is smaller than that of the other two base oils. Moreover, the friction coefficient of methyl oleate is 0.0018, which is approximately 1/3 of that of butyl oleate. Methyl oleate has better lubrication efficiency. The shear simulation results are consistent with the experimental results. The simulation can be used for the molecular design of lubricant materials. The oleic acid amide–containing amine group and the glyceride oleic–containing hydroxyl group were selected as the extreme pressure functional components for shear simulation. Results show that the shear stress of oleic acid amide is much lower than that of oleic acid glyceride when the initial shear temperature and speed change. The extreme pressure lubrication component–containing amine group is better than the extreme pressure lubrication material–containing hydroxyl group. The effects of different oleamide contents in the two-component mixtures on the lubricating properties were investigated through shear simulation, with methyl oleate as the base oil and oleamide as the extreme pressure functional component. The simulation results show that the lubricant has the optimal shear stress when 10% oleamide is added to the lubricant. The base properties of the lubricant were tested using a mixture of 90% methyl oleate and 10% oleamide, formulated as a lubricant. Results show that the friction coefficient can be reduced to 0.03 when 0.5% of the lubricant is added to the base mud. Moreover, the lubricant film formed shows high strength. Then, 1% lubricant was added to the weak-gel drilling fluid to evaluate the effect of the lubricant on the gel structure of the drilling fluid. Results show that adding lubricant does not affect the rheological properties of the drilling fluid. The gel structure of the system also remains stable even after 7 days of continuous ageing. The results of the field experiments in Hua3-01 well show that adding 1% ester-based lubricant to the field drilling fluid reduces the drilling friction by 33%. Thus, the efficiency of directional side drilling can be effectively improved, complicated accidents, such as poor starting and stopping of drilling and stuck jamming, can be avoided, and the goals of reducing quantity and increasing efficiency can be completed.

Two coupled climate models which participated the CMIP6 project (Coupled Model Intercomparison Project Phase 6), the Earth System Model of Chinese Academy of Sciences version 2 (CAS-ESM2-0) and the Nanjing University of Information Science and Technology Earth System Model version 3 (NESM3), were assessed in terms of the impact of four new sea ice parameterization schemes. These four new schemes are related to air-sea heat flux, radiation penetration and absorption, melt ponds, ice-ocean flux, respectively. To evaluate the effectiveness of these schemes, key sea ice variables with and without these new schemes, such as sea ice concentration (SIC) and sea ice thickness (SIT), were compared against observation and reanalysis product from 1980 to 2014. The simulations followed the design of historical experiments within the CMIP6 framework. The results revealed that both models demonstrated improvements in simulating Arctic SIC and SIT when the new parameterization schemes were implemented. The model bias of SIC in some marginal sea ice zones of Arctic was reduced, especially during March. The SIT was increased and the transpolar gradient of SIT was reproduced. The changes of spatial pattern of SIC and SIT after adding new schemes bear similarities between the two coupled models. This suggests that the new schemes have potential for broad application in climate models, especially for those with underestimated SIT.

Modern automotive systems should must satisfy strict reliability requirements. Most of the real vehicle systems and safety-critical networks have complex interconnections. Sensitivities and probabilistic uncertainties of reliability of System with Complex Interconnections (SwCI) can be investigated by the Monte-Carlo Simulation (MCS). The paper focuses on sensitivities and parametrical uncertainties of SwCIs reliability. The proposed method can be used forimplemented in the investigation of uncertainties of SwCIs reliability – in other wordsi.e., for in the determination of critical system elements and to estimateion of the Required Number of Spare Parts (RNSP) of the system, which depends on the probability of allowable spare equipment shortage.

This study presents the design and comprehensive 3D multiphysics simulation of a novel microfluidic immunosensor for real-time, non-invasive monitoring of pro-inflammatory biomarkers in human sweat. The patch-like device, designed using COMSOL Multiphysics, integrates magnetofluidic manipulation with direct-field capacitive sensing. The sensor comprises two distinct units: an immunocomplex enhancement unit, employing a series of microcoils to optimize the binding efficiency, reaction kinetics, and homogeneity of biomarker-magnetic nanoparticle (MNP) interactions, thereby enhancing the sensor's specificity; and a layered capacitive sensing unit, designed to concentrate and detect biomarker-tagged MNPs, thus amplifying sensitivity. Simulations of the capacitive sensing unit revealed a substantial sensitivity increase of up to 42.48\% at an 85\% MNP concentration within the detection zone. These findings highlight the potential of the proposed immunosensor for efficient and precise real-time biomarker monitoring, which may facilitate early disease diagnosis and enable personalized healthcare interventions.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

Advanced Finite Element (FE) modeling and simulations were performed on vehicular crashes into a Three-bar Metal Bridge Rail (TMBR). The FE models of a sedan, a pickup truck, and a TMBR section were adopted in the crash simulations subject to Manual for Assessing Safety Hardware (MASH) Test Level 2 (TL-2) and Test Level 3 (TL-3) requirements. The test vehicle models were first validated using full-scale physical crash tests conducted on a two-bar metal bridge using a sedan and a pickup truck with similar overall physical properties and sizes to their respective vehicles used in the simulations. The validated vehicular models were then used to evaluate the crash performance of the TMBR using MASH Evaluation Criteria for structural adequacy, occupant risk, and post-impact trajectory. The TMBR met all MASH TL-2 requirements but failed to meet the MASH TL-3 Criteria H and N requirements when impacted by the sedan. The TMBR was also evaluated under in-service conditions (behind a 1.52-m wide sidewalk) and impacted by the sedan under MASH TL-3 conditions. The simulation results showed that the TMBR behind a sidewalk met all safety requirements except for the occupant impact velocity in the longitudinal direction, which exceeded the MASH limit by 3.93%.

A series of pyrazolopyrimidines derivatives 4– 11 were synthesized using 1-(6-(3-methoxyphenyl)-4-methylpyridazin-3-yl)-1H-pyrazolo [3,4-d] pyrimidin-4-amine 3 as a starting material. The detailed synthesis, structure assignments of the novel compounds based on chemical and spectroscopic evidence, spectroscopic data, pharmacological properties and molecular docking are reported. The pharmacological evaluation illustrated that many of these compounds have good analgesic, anti-inflammatory and antimicrobial activities.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

Addressing the significant challenge in high-speed cotton dibbling operations in Xinjiang—specifically, the duck bill’s ("Duck bill" is a type of duck-billed bunch planting mechanism or component). shortened opening duration leading to seed throwing and floating—a new crawler-type delayed hole-forming mechanism has been designed. This mechanism extends the duck bill horizontally, thereby prolonging its opening time, enabling cotton sowing speeds of up to 6 km/h. Following agronomic principles for cotton planting, the overall layout of the crawler-type hole-forming mechanism, the structural parameters of the key components and the trajectory of the hole-forming are determined. We use the Discrete Element Method (DEM) and multi-body dynamics coupling method to simulate and analyze the motion process of the device. The fixed the tilt angle of the duck bill α(A), the depth of the duck bill hole-forming into the soil h(B), and the angle of rotation of the moving duck bill β(C) were taken as the experimental factors, with the longitudinal length of cotton seed hole (Y1) and the hole-forming depth of cotton seed hole (Y2) as the response values. The parameter range of each factor and the preliminary influence on the response value were determined through pre-experiments and single-factor simulation test. Based on RecurDyn-EDEM coupling, a quadratic regression orthogonal rotation combination simulation test was carried out. The results show that the order of the primary and secondary factors affecting the Y1 of the time-lapse hole-forming device was: A > C > B. The order of primary and secondary factors affecting the Y2 of the delayed hole forming device was: B > C > A. When the A was 2.4 °, the B was 42.4 mm, and the C was 30.5 °, the performance of the hole-forming was the best, and the Y1 was 26.4 mm, and the Y2 was 25.0 mm. The bench verification test results show that under the optimized combination of operating parameters, the average Y1 was 29.1 mm, and the average Y2 was 23.2 mm. Compared with the results of the previous coupled simulation model, the average relative errors of the two are 7.23 % and 4.36 %, respectively, indicating the accuracy and effectiveness of the established DEM simulation model and virtual test analysis. The hole-forming area and the opening time of the duck bill after the stable operation of the machine were recorded and measured. The calculated hole dislocation rate Hc was 4.33 %, which did not exceed the national standard requirement of 6 %. The qualified rate of hole distance Hx was 94.33 %, which was much higher than the national standard requirement of 80 %. The average opening time of the duck bill at a speed of 6 km/h is 0.45 s, which is much longer than the time required for cotton seeds to fall from the duck bill 0.11 s. It meets the requirements of high-speed cotton planting in China and facilitating advancements in future high-speed planter technology.

The formation of atroposelective biaryl compounds in plants and fungi is well understood; however, the polyketide aglycone synthesis and dimerization in bacteria remain unclear. Thus, the biosynthetic gene cluster (BGC) responsible for antibacterial setomimycin production from Streptomyces nojiriensis JCM3382 was examined in comparison with the BGCs of spectomycin, julichromes, lincolnenins, and huanglongmycin. Setomimycin BGC includes post-PKS assembly/cycling enzymes StmD (C-9 ketoreductase), StmE (aromatase), and StmF (thioesterase) as key components. The heterodimeric TcmI-like cyclases StmH and StmK are proposed to aid in forming the setomimycin monomer. In addition, StmI (P-450) is predicted to catalyze biaryl coupling of two monomeric setomimycin units, with StmM (ferredoxin) specific to setomimycin BGC. The roles of StmL and StmN, part of the nuclear transport factor 2 (NTF-2)-like protein family and unique to setomimycin BGCs, could particularly interest biochemists and combinatorial biologists. α-Glucosidase, a key enzyme in type 2 diabetes, hydrolyzes carbohydrates into glucose, thereby elevating blood glucose levels. This study aimed to assess the α-glucosidase inhibitory activity of EtOAc extracts of JCM 3382 and setomimycin. The JCM 3382 EtOAc extract and setomimycin exhibited greater potency than the standard inhibitor, acarbose, with IC50 values of 285.14 ± 2.04 μg/mL and 231.26 ± 0.41 μM, respectively. Kinetic analysis revealed that setomimycin acts as a competitive inhibitor of α-glucosidase. Molecular docking demonstrated two hydrogen bonds with maltase-glucoamylase chain A residues Thr205 and Lys480 (binding energy = −6.8 kcal·mol⁻¹), two π-π interactions with Trp406 and Phe450, and one π-cation interaction with Asp542. Residue-energy analysis highlighted Trp406 and Phe450 as key in setomimycin's binding to maltase-glucoamylase. These findings suggest that setomimycin is a promising candidate for further enzymological research and potential antidiabetic therapy.

The fractional advection-dispersion equation FADE plays an important role, especially in explaining the process of solute-transport in natural porous media with different degrees of heterogeneity. However, studies of the flow and transport of contaminants in the underground environment are based on the knowledge of many functional parameters of the subsoil. The delay factor caused by nonlinear absorption is one of these parameters inheriting significant ambiguities in its estimation in heterogeneous media. In the study, a fractional advection-dispersion FADE model was developed by the implicit Euler method, based on a Grunwald and Caputo-Liousville approximation to explicitly evaluate and simulate the transport mechanism of contaminants in media with unsaturated porous materials subjected to a nonlinear sorption model. Better solute mass retention was observed for fractional advection-dispersion FADE model. Moreover, the absorption parameter of the retardation coefficient has a better impact on the motion of the solute in a saturated porous medium. In other words, it has a significant effect on the dispersion of pollutants in aquifers. This study highlights the need to characterize the aquifer to predict solute transport in porous media.

This paper proposed a three-layer distributed simulation network architecture: 1. Distributed virtual simulation network, 2. Perception and control sub-network, and 3. Collaborative communication service network. This simulation architecture runs on a distributed platform. The platform can provide a unique virtual scenario and several simulation services to verify the individual robot system's basic perception, control, and planning algorithms and the distributed collaborative algorithms of heterogeneous multi-robot systems. Furthermore, we designed a simulation experiment scenario for classical heterogeneous robot systems such as unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs). At last, We gave a rough estimation model of the bandwidth.

The shear stress generated by wall turbulence is the main cause of wall friction resistance in turbulent flow through pipes. This paper investigates the impact of inserting rest periods (regions of constant Reynolds number) within the pulsating operating cycle of velocity on the fully turbulent flow at large time-averaged Reynolds numbers, using the Large Eddy Simulation (LES) method. The study aims to explore the effect of increasing rest periods within pulsations on drag resistance. The dimensionless shear stress and drag reduction rates during different time periods of rest were analyzed. Numerical simulation results indicate that the pulsating velocity operation mode does not necessarily lead to drag reduction; it may even result in increased resistance. Inserting rest periods within the pulsation cycle can achieve drag reduction effects, with the maximum drag reduction rate reaching 21.8\%. Comparisons with experimental data and Direct Numerical Simulation (DNS) from the literature validate the feasibility of using the LES method for pipe pulsating operation modes.

Tinnitus is a common phantom auditory percept, believed to be related to plastic changes in the brain due to hearing loss. However, tinnitus can also occur in absence of any clinical hearing loss. Then, since there is no hearing loss, the mechanisms that drive plastic changes remain largely enigmatic. Previous studies showed subtle differences in sound-evoked brain activity associated with tinnitus in subjects with tinnitus and otherwise, normal hearing, but the results are not consistent across studies. Here, we aim to investigate those differences using monaural rather than binaural stimuli. Sound-evoked responses were measured using functional magnetic resonance imaging (MRI) in participants with and without tinnitus. All participants had clinically normal audiograms. The stimuli were pure tones with frequencies between 353 and 8000 Hz, presented monaurally. A Principal Component Analysis (PCA) of the response in the auditory cortex revealed no difference in tonotopic organization, which confirmed earlier studies. A GLM analysis showed hyperactivity in the lateral areas of the bilateral auditory cortex. Consistent with the tonotopic map, this hyperactivity mainly occurred in response to low stimulus frequencies. This may be related to hyperacusis, which was associated with tinnitus found in the parahippocampus. This may reflect an interference between tinnitus and spatial orientation.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

Although, promotion of urbanization culture in recent decades has made inevitable development of cities in the world, however, the development can be guided in a direction that leave, to the extent possible, minimum socioeconomic and environmental impacts. For this, it is required to first forecast auto-spreading orientation of cities and suburbs in rural areas over time and then avoid shapeless growth of cities. This paper is an attempt to develop a dynamic hybrid model based on logistic regression (LR), Markov chain (MC), and cellular automata (CA) for prediction of future urban sprawl in fast-growing cities. The model was developed using 12 widely-used urban development criteria, whose significant coefficient was determined by logistic regression, and validated by relative operating characteristic (ROC) analysis. The validated model was run in Guilan, a tourist province in northern Iran with a very high rate of urban development. For this, changes in the area of urban land use were detected over the period of 1989 to 2013 and then, future sprawl of the province was forecasted by the years 2025 and 2037. The analysis results revealed that the area of urban land use was increased by more than 1.7 % from 36012.5 ha in 1989 to 59754.8 ha in 2013, and the area of Caspian Hyrcanian forestland was reduced by 31628 ha. The results also predicted an alarming increase in the rate of urban development in the province by the years 2025 and 2037, during which urban land use is predicted to develop 0.9 % and 1.38 %, respectively. The development pattern is expected to be uneven and scattered, without following any particular direction. The development will occur close to the existing or newly-formed urban basements as well as around major roads and commercial areas. This development, if not controlled, will lead to the loss of 13863 ha of Hyrcanian forests and if the trend continues, 21013 ha of Hyrcanian forests and 20208 ha of Barren/open lands are expected to be destroyed by the year 2037. In general, the proposed model is an efficient tool for the support of urban planning decisions and facilitates the process of sustainable development of cities by providing decision-makers with an overview on future development of cities where the growth rate is very fast.

In this work, two plasmonic structures with two different periodic nanostructures (nanodisk and nanostrip arrays) separated from the gold layer by an ultrathin dielectric Al2O3 layer are proposed, and their optical properties are simulated as 3-dimensional models using COMSOL Multiphysics software tool. The optical responses, such as the amplification of the electric field and the scattering, absorption and extinction cross sections of the two structures, are investigated and compared. The results show that both structures show strong field enhancement in their gap layer, and the structure with the periodic array of metal nanodisks shows stronger field enhancement and larger absorption, extinction, and scattering cross sections in its dipole resonance wavelength, which is defined as a bright plasmonic mode. In addition, some weaker resonant modes are observed for both structures and the reason for their generation is dis-cussed. The analysis of different possible modes in such structures is crucial for their application in various fields.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

In this paper, the boiling flow inside a nanochannel with 700000 argon particle has been simulated by molecular dynamics (MD) simulation. This approach has been employed to analysis the superheated flow and its heat transfer pattern as well. For all simulations an external thrust force varying from 1 PN to 12 PN is exerted on inlet nanoparticles along the channel to have the forced annular boiling flow. Computations reveal that saturation condition and superheat degree have significant impacts on the liquid-vapor interface. Furthermore, because of the major influence of surface tension throughout a nanochannel, the x-velocity of liquid film and vapor core has not considerable fluctuations and stay smooth. All provided results show the behaviors completely similar to the available outcomes in the literature.

A new series of 1,3,4-oxadiazoles derivatives was synthesized, characterized and evaluated for their in vitro and in vivo anti-thrombotic activity. Compounds (3a-3i) exhibited significant clot lysis with respect to negative control and reference drug streptokinase (30,000 IU) while enhanced clotting time (CT) values were observed (130-342 sec) for these tested compounds than the standard drug heparin (110 sec.). High affinity towards 1NFY with greater docking score was observed for the compounds (3a, 3i, 3e, 3d and 3h) than the control ligand RPR200095. In addition, very good inhibitory potential against factor Xa (F-Xa) was observed with higher docking scores (5612-6270) with ACE values (–189.68 to –352.28 kcal/mol) than the control ligand RPR200095 (Docking score 5192; ACE –197.81 kcal/mol. In vitro, in vivo and in silico results proposed that these newly synthesized compounds can be used as anti-coagulant agents.

Surgical simulators are crucial in early craniofacial and plastic surgical training, necessitating synthetic materials that accurately replicate tissue properties. Recent critiques of our lab’s currently deployed silicone surrogate have highlighted numerous areas for improvement. To further refine our models, our group's objective is to find a composition of materials that is closest in fidelity to native oral mucosa during surgical rehearsal by expert craniofacial surgeons. Fifteen platinum silicone-based surrogate samples were constructed with variable hardness and slacker percentages. These samples underwent evaluation of tactile sensation, hardness, needle puncture, cut resistance, suture retention, defect repair, and tensile elasticity. Expert craniofacial surgeon evaluators provided focused qualitative feedback on selected top-performing samples for further assessment and statistical comparisons. Evaluation revealed surrogate characteristics with satisfactory to good performance. Sample 977 exhibited the highest performance, and comparison with the original surrogate (sample 810) demonstrated significant improvements in critical areas, emphasizing the efficacy of the refined composition. The study identified a silicone composition that directly addresses the feedback received by our team’s original silicone surrogate. The study underscores the delicate balance between biofidelity and practicality in surgical simulation. The need for ongoing refinement in surrogate materials is evident to optimize training experiences for early surgical learners.

Surgical simulators are crucial in early craniofacial and plastic surgical training, necessitating synthetic materials that accurately replicate tissue properties. Recent critiques of our lab’s currently deployed silicone surrogate have highlighted numerous areas for improvement. To further refine our models, our group's objective is to find a composition of materials that is closest in fidelity to native oral mucosa during surgical rehearsal by expert craniofacial surgeons. Fifteen platinum silicone-based surrogate samples were constructed with variable hardness and slacker percentages. These samples underwent evaluation of tactile sensation, hardness, needle puncture, cut resistance, suture retention, defect repair, and tensile elasticity. Expert craniofacial surgeon evaluators provided focused qualitative feedback on selected top-performing samples for further assessment and statistical comparisons. Evaluation revealed surrogate characteristics with satisfactory to good performance. Sample 977 exhibited the highest performance, and comparison with the original surrogate (sample 810) demonstrated significant improvements in critical areas, emphasizing the efficacy of the refined composition. The study identified a silicone composition that directly addresses the feedback received by our team’s original silicone surrogate. The study underscores the delicate balance between biofidelity and practicality in surgical simulation. The need for ongoing refinement in surrogate materials is evident to optimize training experiences for early surgical learners.

To address the requirements of sonar imaging, such as high receiving sensitivity, wide bandwidth, wide receiving angle, an AlN PMUT with an optimized ratio of 0.6 for the piezoelectric layer diameter to backside cavity diameter is proposed in this paper. A sample AlN PMUT is designed and fabricated with SOI substrate-based bulk MEMS process. The characterization test result of the sample demonstrates a -6 dB bandwidth of approximately 500 kHz and a measured receiving sensitivity per unit area of at 1.37 V/μPa/mm2, which significantly surpasses the performance of previously reported PMUTs. The -6 dB horizontal angles of the AlN PMUT at 300 kHz and 500 kHz are measured 68.30° and 54.24°, respectively. To achieve an accurate prediction of its characteristics when being packaged and assembled in a receive array, numerical simulations with the consideration of film stress are conducted. The numerical result shows a maximum deviation of ±7% in the underwater receiving sensitivity across the frequency range of 200 kHz to 1000 kHz and a deviation of about 0.33% in the peak of underwater receiving sensitivity comparing to the experimental data. By such good agreement, the simulation method reveals its capability of providing theoretical foundation for enhancing the uniformity of the AlN PMUTs in future studies.

This study investigates the impact of vertical greenery systems (VGS) applied to heavyweight walls on indoor thermal conditions in a building module situated in the Mediterranean climate of Catania, Italy. Using dynamic simulations in TRNSYS, the research compares the thermal behavior of walls constructed from hollow clay blocks (Poroton) and lava stone blocks with a lightweight wall setup already in place at the University of Catania. The primary focus is on evaluating the VGS’s effect on reducing peak inner surface temperatures and moderating heat flux fluctuations entering the building. The findings indicate that adding a vertical greenery layer to heavyweight walls can decrease the peak inner surface temperature by up to 1.0°C compared to the same wall without vegetation. However, the greenery’s impact on mitigating heat flux fluctuations is less pronounced than in the case of the lightweight wall. This research underscores the potential of green facades in enhancing indoor thermal comfort in regions with climates similar to the Mediterranean, providing valuable insights for sustainable building design and urban planning.

An important parameter in the development of a new drug is the drug's affinity to the identified target (protein/enzyme). Predicting the ligand binding to the target (protein/enzyme) by molecular simulation would allow the synthesis to be restricted to the most promising compounds.A restricted hybrid HF-DFT calculation was performed in order to obtain the most stable conformer of each ligand and a series of DFT calculations using the B3LYP levels with 6-31G* basis set has been conducted. The docking studies of the quinolone compounds will be performed with the CLC Drug Discovery Workbench to identify and visualize the ligand-receptor interaction mode.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

: In this paper we present an optimization of the planar manufacturing scheme for stretch-free, shape induced metal interconnects to simplify the fabrication with the aim of maximizing the flexibility in the structure regarding to stress and strain. The Formation of trenches between silicon islands are actively used in the lithographic process to create arc shape structures by spin coating resist into the trenches. The resulting resist form is used as a template for the metal lines, which are structured on top. Because this arc shape is beneficial for the flexibility of these bridges. The trench depth as a key parameter for the stress distribution is investigated by applying numerical simulations. The simulated results show that the increase in penetration depth of the metal bridge into the trench increases the tensile load which is converted into a shear Force Q(x), that usually leads to increased strains the structure can generate. For the fabrication the filling of the trenches with resist is optimized by varying the spin speed. Compared to the theoretical resistance, the current-voltage measurements of the metal bridges show a similar behavior and almost every structural variation is capable of functioning as a flexible electrical interconnect in a complete island-bridge array.

Hydraulic fracturing has enabled production from unconventional reservoirs in the U.S., but production rates often decline sharply, limiting recovery factors to under 10%. This study optimizes the CO2 huff-n-puff process for multistage-fractured horizontal wells in Wolfcamp A formation in the Delaware Basin. The potential for enhanced oil recovery and CO2 sequestration simultaneously was addressed using a coupled geomechanics-reservoir simulation. Geomechanical properties were derived from a 1D mechanical earth model and integrated into reservoir simulation to replicate hydraulic fracture geometries. The fracture model was validated using a robust production history matching. Fluid phase behavior analysis refined the equation of state, and 1D slim tube simulations determined a minimum miscibility pressure of 4300 psi for CO2 injection. After the primary production phase, various CO2 injection rates were tested from 1 to 25 MMSCFD/well, resulting in incremental oil recovery ranging from 6.3% to 69.3%. Different injection, soaking, and production cycles were analyzed to determine the ideal operating condition. The optimal scenario improved cumulative oil recovery by 68.8% while keeping the highest CO2 storage efficiency. The simulation approach proposed by this study provides a systematic workflow for evaluating and optimizing CO2 huff-n-puff in hydraulically fractured wells, enhancing the recovery factor of unconventional reservoirs.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

This paper presents a study on developing of a new exoskeleton for ankle joint rehabilitation with three degrees of freedom (3 DOFs). The primary attention is paid to the process of designing and modelling the device aimed at restoring the lost functions of joint mobility. The authors carried out a complex analysis of the functional requirements of the exoskeleton based on the research of potential user’s needs, which allowed them to develop a conceptual model of the proposed de-vice. In this study, a prototype of the exoskeleton is designed using modern additive technolo-gies. A prototype of the proposed device underwent virtual testing in conditions maximally close to the real one, which confirmed its effectiveness and comfort of use. The main results of the work indicate the promising potential of the proposed solution for application in rehabilitation practice, especially for patients with ankle joint injuries and diseases.

Polydatin, a polyphenolic compound sourced from various natural origins, has garnered attention due to its potential anti-tumor properties and low toxicity. This research utilized Molecular Docking methods to investigate the molecular interactions between Polydatin and the Crystal Structure of Human UDP-glucuronic acid decarboxylase (UXS1), aiming to uncover the mechanisms contributing to its anti-tumor effects. The study revealed a substantial binding energy value of approximately -10 kcal/mol for the Polydatin-UXS1 interaction, indicating a robust and favorable binding. This suggests that Polydatin holds significant promise in cancer research, offering insights into its ability to interact with and potentially modulate the activity of UXS1. Moreover, the additional step of predicting toxicity properties using the pKCSM server provides valuable insights into the safety profiles of polydatin ( or piceid). From these results, the parameters for polydatin: —Max. tolerated dose (human),- Oral Rat Acute Toxicity (LD50), and - Oral Rat Chronic Toxicity (LOAEL)—suggest a favorable safety profile.These findings position Polydatin as a compelling candidate for further exploration in cancer research, highlighting both its efficacy and safety considerations.

Decision sciences (DSC) involve studying complex dynamic systems and processes to aid informed choices subject to constraints in uncertain conditions. It integrates multidisciplinary methods, techniques, and strategies to evaluate decision engineering processes, identifying alternatives and providing insights towards enhancing prudent decision-making. This study analyzes the evolutionary trends and innovation in DSC education and research to uncover the transformations over the years. We employ the science mapping method, text analytics, and metadata from bibliographic databases to evaluate thematic and social structures. The results highlight data science methods, including data mining and business/learning analytics as essential components. The evolutionary trends in DSC education and research mirror the development in practice, including technological transformation, computer science advances, and engineering processes. Sustainable education through virtual/online learning also constitutes a significant component of scientific production. The evolutionary trends in DSC education and research highlight innovative pedagogical approaches and strategies, including computer simulation and games ('play and learn'). The current era witnessed generative artificial intelligence (GenAI) adoption (e.g., ChatGPT) in teaching, learning, and scholarly activities amidst challenges (academic integrity, plagiarism, intellectual property violations, and other ethical and legal issues). Future research will implement and integrate AI automatic detection systems to address some GenAI adoption challenges.

Corona virus disease 2019 (COVID-19) is caused by a Severe Acute Respiratory Syndrome-Coronavirus 2 (SARS-CoV-2), which is a positive strand RNA virus. The SARS-CoV-2 genome and its association to SAR-CoV-1 vary from ca. 66% to 96% depending on the type of betacoronavirdeae family members. With several drugs, viz. chloroquine, hydroxychloroquine, ivermectin, artemisinin, remdesivir, azithromycin considered for clinical trials, there has been an inherent need to find distinctive antiviral mechanisms of these drugs. Curcumin, a natural bioactive molecule has been shown to have a therapeutic potential for various diseases, but its effect on COVID-19 has not been explored. In this study, we show the binding potential of curcumin targeted to a variety of SARS-CoV-2 proteins, viz. spike glycoproteins (PDB ID: 6VYB), nucleocapsid phosphoprotein (PDB ID: 6VYO), membrane glycoprotein (PDB ID: 6M17) along with nsp10 (PDB ID: 6W4H) and RNA dependent RNA polymerase (PDB ID: 6M71) structures. Our results indicate that curcumin has high binding affinity towards nucleocapsid and nsp 10 proteins with potential antiviral activity.

7α- and 7β-hydroxysteroid dehydrogenases (HSDH) are a pair of enzymes that can catalyze the isomerization of hydroxyl group at site 7 of bile acids. In previous study, we found that the activities of 7α- and 7β-HSDH can be inhibited by bilirubin. In order to clarify the impact, the effects of bilirubin on enzymes were studied by kinetics, spectrum and docking analysis. Relative activity of 7α-HSDH remained less than 40 % under 1 mM bilirubin, for 7β-HSDH, only 18 % activity left at the same condition. Using taurochenodeoxycholic acid (TCDCA) as substrate, the Km of 7α-HSDH was up to 0.63 mM from 0.24 mM after binding with bilirubin, the Km of 7β-HSDH rose from 1.14 mM to 1.87 mM for the catalysis of tauroursodeoxycholic acid (TUDCA). The affinity of 7α- and 7β-HSDH to substrate decreased with the effect of bilirubin. The binding of bilirubin with 7α- or 7β-HSDH were analyzed by UV–Vis spectra, Fluorescence spectra and Circular dichroism (CD) spectra. The results reflected that bilirubin caused a slight change in the secondary structure of 7α- or 7β-HSDH, and the changes were correlated with the ratio of bilirubin to enzyme. 10 candidate molecular docking results were presented to reflect the binding of bilirubin with 7α- or 7β-HSDH and to explore the inhibition mechanism. This research not only provides the more in-depth understanding of 7α- and 7β-HSDH, but also reminds us to avoid the inhibition of bilirubin on hydroxysteroid dehydrogenases.

This study uses simulation and experimental methodologies to explore the efficacy of bi-sectional horizontal kinetic shading systems (KSS) featuring horizontal fins in enhancing daylight comfort across various climates. Given the increasing energy demands and shifting climatic patterns, optimizing daylight levels while minimizing solar heat gain is vital. The paper introduces a bespoke horizontal bi-sectional KSS, simulated in three distinct climates—Wroclaw, Tehran, and Bangkok—using Climate Based Daylight Modelling methods with Ladybug and Honeybee tools in Rhino software. The study employs standard daylight metrics such as Useful Daylight Illuminance (UDI) and Daylight Glare Probability (DGP), along with custom metrics designed to capture the specific dynamics of the bi-sectional KSS. Initial simulations indicated that the KSS significantly improved daylight distribution and uniformity, reducing glare and over-illumination risks by av. 42.34%. Including KSS switching schedules, which are seldom detailed in similar research, enhances the reproducibility and understanding of findings. Subsequently, a physical reduced-scale mock-up of the bi-sectional KSS was tested under real-weather conditions in Wroclaw (lat. 51° N) during June-July 2024. The mock-up utilized two chambers: one equipped with the prototype of bi-sectional KSS and the second without any protection. The operation of fins was guided by two stepper motors controlled by a Python script running on a Raspberry Pi 3 minicomputer. The control chamber served to benchmark the bi-sectional KSS's efficiency by providing results that would be expected if no shading system were installed. The experimental outcomes supported the simulations, demonstrating the KSS's robustness in reducing high illuminance levels to the target comfort level, thus enhancing indoor visual comfort. The values below 3,000 lux were maintained for 68% of the time. However, it must be explicitly stated that during the June-July 2024 heat waves, the illuminance levels inside the test room momentarily exceeded the comfort threshold of 3,000 lux, reaching up to 4,674 lux. Through quantitative and qualitative analyses, the paper advocates for the broader application and further development of KSS as a climate-responsive shading system in diverse architectural contexts.

Inflammation is a vital aspect of the body's immune response, appearing either as an acute reaction that swiftly develops (e.g., after injury or during an infection) or as a chronic condition that persists over a prolonged period, often linked with autoimmune disorders or cancer. This study introduces potential TNF-alpha inhibitors investigated by Molecular Docking investigation. They are Dactolisib with a binding energy of -10.1 kcal/mol, Nilotinib with -9.6 kcal/mol, Eltrombopag with -9.7 kcal/mol, Radotinib with -9.6 kcal/mol, and Nilotinib again with -9.7 kcal/mol. Additionally, Hypericin exhibited a notable binding energy of -9.9 kcal/mol, suggesting its potential as a natural TNF-alpha inhibitor. While these computational results are preliminary, they provide a foundation for further biological studies to confirm their efficacy. The significance of these findings extends to the scientific community, offering potential applications in the field of inflammatory diseases.

For the first time, this study identified seven potential ligands with high binding energies through the docking approach against the Crystal Structure of human Melanoma-associated antigen B1 (MAGEB1). The ligands—Imatinib, Bafatinib, Diosmin, Ginkgetin, Bilobetin, Amentoflavone, and Hypericin—showing strong binding energies around -10 kcal/mol, indicate a potentially robust interaction with the target protein. Moreover, the additional step of predicting toxicity properties using the pKCSM server provides valuable insights into the safety profiles of these ligands. From these results, the parameters for Diosmin: —Max. tolerated dose (human),- Oral Rat Acute Toxicity (LD50), and - Oral Rat Chronic Toxicity (LOAEL)—suggest a favorable safety profile, making it a potential candidate for further consideration against Melanoma. Moving forward, it's advisable to conduct further experimental validations, including in vitro and in vivo studies, to confirm the efficacy and safety of Diosmin and other potential ligands. Consideration of pharmacokinetics, metabolism, and specific mechanisms of action will contribute to a comprehensive understanding of these compounds' potential as therapeutic agents.

The novel coronavirus disease 19 (COVID-19) has resulted in an estimated 20 million excess deaths and the recent resurgence of COVID-19 in China is predicted to result in up to 1 million deaths over the next few months. With vaccines unable to halt transmission it is important to continue our quest for safe, effective, affordable drugs that will be available to all countries. Drug repurposing is one of the strategies being explored in this context. Recently, out of 7,817 approved drugs, 214 candidates were systematically down-selected using a combination of 11 filters including approval status, assay data against SARS-CoV-2, pharmacokinetic, pharmacodynamic and toxicity profiles. These drugs were subjected in this study to virtual screening against various targets of SARS-CoV-2 followed by molecular dynamic studies of the best scoring ligands against each target. The chosen molecular targets were Spike receptor binding domain, Nucleocapsid protein RNA binding domain, and key non-structural proteins 3, 5, 12, 13 and 14. Four drugs approved for other indications — alendronate, cromolyn, natamycin and treprostinil — look sufficiently promising from our in silicostudies to warrant further in vitro and in vivo investigations as appropriate to ascertain their extent of anti-viral activities.

Inhibition of acetylcholinesterase (AChE) enzyme is a known procedure to treat severe Alzheimer's disease through increasing the acetylcholine level in the brain and thus slowing down the progression of Alzheimer's symptoms. The approved medications are only considered as palliative and addressed some reported deficiencies. Therefore, the demand for safe and effective compounds is substantially increasing. A newly series of coumaryl 1,3-selenazoles derivatives was synthesized in four steps. Then, their antioxidant activities were evaluated using DPPH, ABTS cation radical scavenging assay and cupric reducing antioxidant capacities (CUPRAC). The anticholinesterase activities were evaluated using the Ellman method. Then, the docking studies were carried out to explain the possible correlation between in vitro anticholinesterase activity results and the ligand-receptor interactions. Ten new coumaryl 1,3-selenazoles (5a-5d series and 6a-6f series) derivatives were successfully synthesized. The DPPH radical scavenging assay showed that all tested compounds have IC50 value > 200 μM, for ABTS cation radical scavenging assay the IC50 value > 1000 μM and for CUPRAC assay the IC50 value > 200 μM. Compound 5c was found to be the most active compound against AChE and BChE in its series with IC50 value for AChE is 99.76 μM and IC50 for BChE is 140.28 μM while 6b exhibited the most potent inhibition in its series with IC50 value for AChE is 56.01 μM and IC50 for BChE is 121.34 μM. Besides, the docking studies showed that compound 5c and 6b formed π-π stacking interaction with aromatic residues at the active site of AChE and BChE, which is responsible for inhibiting the enzymes. This shows that the synthesized compounds contain skeletal structures that can interact and inhibit within the enzymes active site.

Agricultural greenhouse is largely answered in the agricultural sphere, despite the shortcomings it has, including overheating during the day and night cooling which sometimes results in the thermal inversion mainly due to its low inertia. The glasshouse dressed chapel is relatively more efficient than the conventional tunnel greenhouse. Its proliferation on the ground is more or less timid because of its relatively high cost[14-22]. Agricultural greenhouse aims to create a favorable microclimate to the requirements of growth and development of culture, from the surrounding weather conditions, produce according to the cropping calendars fruits, vegetables and flower species out of season and widely available along the year. It is defined by its structural and functional architecture, the quality thermal, mechanical and optical of its wall, with its sealing level and the technical and technological accompanying[12-13]. The greenhouse is a very confined environment, where multiple components are exchanged between key stakeholders and them factors are light, temperature and relative humidity[8]. This state of thermal evolution is the level sealing of the cover of its physical characteristics to be transparent to solar, absorbent and reflective of infrared radiation emitted by the enclosure where the solar radiation trapping effect otherwise called "greenhouse effect" and its technical and technological means of air that accompany. The socio-economic analysis of populations in the world leaves appear especially the last two decades of rapid and profound transformations These changes are accompanied by changes in eating habits, mainly characterized by rising consumption spread along the year[14]. To effectively meet this demand, greenhouse-systems have evolved, particularly towards greater control of production conditions (climate, irrigation, ventilation techniques, CO2 supply, etc ...). Technological progress has allowed the development of greenhouses so that they become increasingly sophisticated and of an industrial nature (heating, air conditioning, control, computer, regulation, etc ...). New climate driving techniques have emerged, including the use of control devices from the classic to the use of artificial intelligence[10-11] such as neural networks and / or fuzzy logic, etc... As a result, the greenhouse growers prefer these new technologies while optimizing the investment in the field to effectively meet the supply and demand of these fresh products cheaply and widely available throughout the year.

Perovskite solar cells (PSCs) are vital for their optical and electrical properties, with lead-based PSCs reaching a remarkable efficiency of 26.1%, while tin-based counterparts achieve 18.71%. Due to lead's toxicity, there's a push for alternatives like tin. However, tin-based PSCs suffer from stability issues and high defect density states, necessitating the development of cost-effective, high-performance, and eco-friendly alternatives. In this study, we designed a hetero-junction architecture using MASnI3-based Perovskite, opti-mized with SCAPs-1D. After exhaustive analysis, our device achieved a power conversion efficiency of 24.18%, with enhanced parameters including Voc of 0.09323V, Jsc of 30.8360 mA/cm2, and FF of 84.10%. Recombination rates, particularly Shockley-Read Hall recom-bination, were significantly reduced. Parametric analyses, encompassing absorber layer thickness, band gap, defect density, doping concentration, and operating temperature, in-dicate potential efficiency enhancements. This underscores the viability of Sn-based PSCs as a cost-effective, efficient, and environmentally benevolent alternative to lead-based counterparts, promising advancements in future research and development efforts.

The object of study in the article is the auxiliary variable-frequency electric drive onboard of an AC electric locomotive, and more precisely, the structure and parameters of the control system of the active corrector of power factor (ACPF), which is part of the electric drive, as a unit that ensures electromagnetic compatibility of the electric drive with other equipment on board the electric locomotive and catenary and its energy efficiency. The topic of the article's research is the substantiation of the structure of the ACPF control system, the choice of types (transfer functions) of controllers and the calculation of their parameters. The research method chosen was the calculation of the transfer functions of the controllers of the cascaded loops control system, followed by computer simulation using the OrCAD software. The results of simulating a cascaded two loops control system of an ACPF with different types of controllers are presented and analytically compared. It is concluded that it is advisable to use a cascaded two loops control system, containing a voltage control loop and a current control loop. The best results show the simulation when using an aperiodic current controller (A-controller) and a proportional-integral voltage controller (PI-controller). The data obtained serve as the basis for further improvement of the operation of the ACPF by enhancing and optimizing the settings, structure and algorithms of the control system, which, with the selected hardware of power converter unit, will allow the ACPF to perform its functions with a high degree of reliability in an entire range of disturbing and control influences.

Natural products from plants such as, chemopreventive agents attract huge attention because of their low toxicity and high specificity. The rational drug design in combination with structure based modeling and rapid screening methods offer significant potential for identifying and developing lead anticancer molecules. Thus, the molecular docking method plays an important role in screening a large set of molecules based on their free binding energies and proposes structural hypotheses of how the molecules can inhibit the target. Several peptide based therapeutics have been developed to combat several health disorders including cancers, metabolic disorders, heart-related, and infectious diseases. Despite the discovery of hundreds of such therapeutic peptides however, only few peptide-based drugs have made it to the market. Moreover, until date the activities of cyclic peptides towards molecular targets such as protein kinases, proteases, and apoptosis related proteins have never been explored. In this study we explore the in silico kinase and protease inhibitor potentials of cyclosaplin as well as study the interactions of cyclosaplin with other cancer-related proteins. Previously, the structure of cyclosaplin was elucidated by molecular modeling associated with dynamics that was used in the current study. Docking studies showed strong affinity of cyclosaplin towards cancer-related proteins. The binding affinity closer to 10 indicated efficient binding. Cyclosaplin showed strong binding affinities towards protein kinases such as EGFR, VEGFR2, PKB and p38 indicating its potential role in protein kinase inhibition. Moreover, it displayed strong binding affinity to apoptosis related proteins and revealed the possible role of cyclosaplin in apoptotic cell death. The protein-ligand interactions using LigPlot displayed some similar interactions between cyclosaplin and peptide-based ligands especially in case of protein kinases and a few apoptosis related proteins. Thus, the in silico analyses gave an insight of cyclosaplin as a potential apoptosis inducer and protein kinase inhibitor.

A better understanding of high temperature processes in slags contributes to facilitate knowledge based design of the solidified product. Here, a slag analogue with a nominal composition of 17 wt% LiMnO2 and 83 wt% Ca2SiO4 was synthesized encountering fairly high cooling rates. The Mn species from 1223 K to 1773 K was simulated using a thermodynamic model assuming a homogeneous melt. The micro-composition including the Mn species of the solidified slag was determined experimentally and was used as basis for molecular dynamics (MD) simulation. The MD simulation provides information on structure and viscosity at high temperatures, otherwise difficult to access. These parameters significantly influence oxidation state of redox-active elements and the solidified product. The micro-composition analyzed by electron probe micro analysis (EPMA) and synchrotron based micro-X-ray fluorescence (micro-XRF) showed that Mn-rich and Ca-Si-rich phases are separated. While the Mn-O phases did not contain noticeable Ca, the Ca2SiO4 phase had incorporated 0.6 wt% of Mn. The slag solidified into round shaped and droplet shaped grains of a Li-Mn-oxide, some Mn3O4 and Ca2SiO4. The powder X-ray diffraction (PXRD) confirmed the formation of larnite, the identity of the Li-Mn-oxide however remained inconclusive. The Mn oxidation state (OS) was identified using synchrotron based micro-X-ray absorption near edge spectroscopy (micro-XANES). The Mn-O grains, matched well with Li-Mn-oxides and a Mn OS: +3 e.g. LiMn3+O2. Small areas matching Hausmannite (Mn2+Mn23+O4) were also identified. The OS of Mn in the silicate phase could not be identified. For comparison a slowly cooled slag analogue with similar composition however higher Si content, was also subjected to micro-XANES. The slowly cooled slag formed long Mn-rich needles in a matrix of large calcium silicate crystals. The Mn-rich crystals matched well with the XANES spectrum of a Mn3+ Li-oxide like LiMn3+O2. At the rim of the needles the Mn-spectra matched well the Hausmannite (Mn2+Mn23+O4) reference. In the silicate phases Mn had a OS: +2, unambiguously. The melt structure at different temperatures of two compositions i.e. LiMn3+O2 and Ca2SiO4 was simulated using molecular dynamics (MD). They serve as model compositions assuming a heterogeneous melt. The results show significant different degrees of polymerization and viscosity. Information from MD simulations can support the identification of potentially different oxygen permeability and with that prediction of oxidation states. The bulk composition was identified by inductively coupled plasma optical emission spectrometry (ICP-OES), bulk structure by PXRD and bulk species by lab-XANES. The synchrotron micro analysis including micro-XRD were performed at the microfocus beamline I18 at the Diamond Light Source. Pure reference compounds were prepared and characterized with the same multi-modal approach.

The Xihan River basin is located in the southern part of Gansu Province, where flood disasters occur frequently in summer and autumn, which easily pose significant risks to human life. In order to improve the accuracy of flood disaster predictions and early warnings, a flood model suitable for this region was constructed based on the HEC-HMS (Hydrologic Engineering Center's-hydrologic modeling system) model and used to determine the critical areal rainfall for flood disasters. Calibration of this model was performed using data of four flood events from May to October between 2020 and 2021, reserving data of two additional flood events for model validation. Using the calibrated HEC-HMS model, the critical areal rainfall was determined for the Pingluo and Tanjiaba hydrological stations in the basin through the model testing method. The results indicate that: (1) The stable infiltration rate of the XiHanShui River Basin was between 0.06 and 0.10 mm/h, with runoff concentration times primarily varying from 22.5 to 24.1 hours, a direct runoff storage coefficient was 0.2 hours, and a base flow index decay constant seted at 0.03 hours. (2) During the calibration and validation periods, the average peak flow relative error was 7.56%, the average runoff volume relative error was 14.76%, the average peak occurrence time difference was -0.5 hours, and the Nash efficiency coefficient was 0.769. (3) The warning areal rainfall for the Pingluo and Tanjiaba hydrological stations were 108.1mm and 128.5mm, and the guaranteed areal rainfall were 230.8mm and 184.6mm. The HEC-HMS model demonstrated high applicability and accuracy in simulating flood events in the XiHanShui River Basin, providing technical support for hydrological research and operational applications in the region.

The dynamic response of the shed-tunnel structure under rockfall impact attracts much attention in recent years. However, the research on the dynamic response of the shed-tunnel structure under rockfall impact mostly focuses on the rockfall single impact, while in practical engineering, the shed-tunnel structure often encounters the rockfall repeated impacts during its service life. Therefore, this research focuses on exploring the dynamic response characteristics of the shed-tunnel structure under the rockfall repeated impacts. First of all, based on the model test of the shed-tunnel under rockfall impact as a reference, the FEM (Finite Element Method)-SPH (Smoothed Particle Hydrodynamics) coupling numerical calculation model is established based on ANSYS/LS-DYNA finite element code. The numerical simulation of the dynamic response of the shed-tunnel structure under rockfall impact is realized, and the rationality of the model is verified. Then, with this model and the full restart technology of LS-DYNA code, the effects of four factors, e.g. rockfall mass, rockfall impact velocity, rockfall impact angle and rockfall shape, on the impact force and impact depth of the buffer layer, the maximum plastic strain and axial force of the rebar, the shed roof vertical displacement and the shed-tunnel plastic strain are studied. These results show that the cumulative deformation and damage of the shed-tunnel structure caused by the rockfall repeated impacts play an important role in the destruction of the shed-tunnel structure, and the special attention should be paid to this issue.

Therapies targeting amyloid, such as monoclonal antibodies like Lecanemab, Aducanumab, and Donanemab, have garnered FDA approval but remain controversial due to limited clinical benefits and significant side effects against Alzheimer. The present theorical work utilized Virtual Screening and Docking techniques to explore potential small natural molecules' interactions with the KIBRA protein, a promising target for drug development. Kibra protein is considered a biomarker for synaptic dysfunction and cognitive decline. Employing Autodock Vina and Pyrx software, on several natural compounds and found Hypericin to exhibit the lowest binding energy of approximately -9 kcal/mol. Previous studies have highlighted Hypericin's strong affinity for Alzheimer's Disease-associated targets like ABAD and BACE1. These findings suggest Hypericin could be as a potential therapeutic agent for Alzheimer's Disease. Further research is warranted to validate its efficacy and safety for clinical use.

Coronavirus disease 2019 (COVID-19) has been first appeared in Wuhan, China but its fast transmission, led to its widespread prevalence in various countries and make it a global concern. In addition, lack of a definitive treatment is another concern that needs to be attention. Researchers have come up with several options, which are not certain, but protease inhibitor and some antiviral agent are in the forefront. In this study a virtual screening procedure employing docking of different databases including 1615 FDA approved drugs was used to identify new potential small molecule inhibitors for protease protein of COVID-19. The docking result indicates that among all, simeprevir (Hepatitis C virus (HCV) NS3/4A protease inhibitor) could fit well to the binding pocket of protease and because of some other positive features including ADME profile, might be a helpful treatment option for COVID-19.

In the search of potent α-amylase inhibitors, we have synthesized seventeen derivatives of 2-mercaptobenzimidazole bearing sulfonamide (1-17) and evaluated for their α-amylase inhibitory potential. All compounds display a variable degree of α-amylase activity having IC50 values ranging between 0.90 ± 0.05 to 11.20 ± 0.30 µM when compared with the standard drug acarbose having IC50 value 1.70 ± 0.10 µM. Compound 1, 2, 11, 12 and 14 having IC50 values 1.40 ± 0.10, 1.30 ± 0.05, 0.90 ± 0.05, 1.60 ± 0.05 and 1.60 ± 0.10 µM respectively were found many folds better than the standard drug acarbose. The remaining analogs showed good inhibitory potentials. All the synthesized compounds were characterized by HREI-MS, 1H and 13C-NMR. Structure activity relationship (SAR) has been recognized for all newly synthesized analogs. Through molecular docking study, binding mode of active analogs with α-amylase enzyme was confirmed.

We have synthesized quinoxaline analogs (1-25), characterized by 1HNMR and HREI-MS and evaluated for thymidine phosphorylase inhibition. Among the series, nineteen analogs showed better inhibition when compared with the standard inhibitor 7-Deazaxanthine (IC50 = 38.68 ± 4.42 µM). The most potent analog among the series is analog 25 with IC50 value 3.20 ± 0.10 µM. Sixteen analogs 1, 2, 3, 4, 5, 6, 7, 12, 13, 14, 15, 16, 17, 18, 21and 24 showed outstanding inhibition which is many folds better than the standard 7-Deazaxanthine. Two analogs 8 and 9 showed moderate inhibition. A structure- activity relationship has been established mainly based upon the substitution pattern on the phenyl ring. The binding interactions of the active compounds were confirmed through molecular docking studies.

The advanced industrial systems are characterized by complex event-driven processes. The specification and computer analysis are illustrated by the common problem of a servo drive with the PWM controller. A mathematical model from the class of Cauchy problems with non-liner control logic is presented to resolve the task discussed. The designed model is performed in two stages: the mathematical model specification (modeling) and implementation (simulation). Two approaches to make a model specification are considered, the first one is the traditional structural technique, and the advanced method is based on the finite state machine paradigm. Structural and finite state software models are built in progressive simulation tools. Computer implementation of the software models of hybrid systems is performed using platform built-in libraries with numerical methods and algorithms for correct event detection. The results of computational experiments for transient processes of phase variables are qualitatively identical, that proves the adequacy of the developed models. The algorithm for asymptotic event detection is considered in detail. This technique demonstrated the best results by the one-sidedness criterion, which is explained by using the author’s algorithm for the integration step determining and the event function dynamics monitoring in the vicinity of the event limits.

Diabetes mellitus (DM) is one of the most dangerous metabolic diseases with high rate of mortality worldwide. It is well known that insulin resistance and deficiency in insulin production from pancreatic β-cells are the main characteristic of DM. Due to the detrimental side effects of the current treatment, there is a considerable need to develop new effective antidiabetic drugs, especially alpha-glucosidase and alpha-amylase inhibitors with lesser adverse effects. These inhibitors are known to be directly involved in the delay of carbohydrate digestion, resulting in a reduction of glucose absorption rate and consequently reduce the post-prandial raise of plasma glucose, which can reduce the risk of long-term diabetes complications. Hence, natural products are well-known sources for the discovery of new scaffold for drugs discovery, including new antidiabetic drugs. The phytochemical investigation of Salvia aurita collected from Hogobach pass, Eastern Cape, South Africa (SA), yielded four known abietane diterpenes namely carnosol (1), rosmanol (2), 7-methoxyrosmanol (3), 12-methoxycarnosic acid (4) and one flavonoid named 4,7-dimethylapigenin (5). Structural characterization of these isolated compounds was conducted using 1 and 2D NMR, in comparison with reported spectroscopic data. These compounds are reported for the first time from S. aurita. The biological evaluation of the isolated compound against alpha-glucosidase exhibited strong inhibitory activities for 3 and 2 with IC50 values of 4.2 ± 0.7 and 16.4 ± 1.1 µg/mL respectively, while 4 and 1 demonstrated strong alpha-amylase inhibitory activity amongst the isolated compounds with IC50 of 16.2 ± 0.3 and 19.8 ± 1.4 µg/mL. Molecular docking analysis confirms strong inhibitory activity of 3 against alpha-glucosidase. Additionally, excellent antioxidant capacities were displayed by 2, 1 and 3 respectively as ORAC (25789.9 ± 10.5; 23961.8 ± 14.1; 23939.3 ± 2.4) µM TE/g; 1 and 2 as FRAP (3917.8 ± 2.1; 1522.3 ± 0.9) µM AAE/g; 5 and 2 as TEAC (3190.4 ± 2.8; 2055.0 ± 2.6) µM TE/g. The methanolic extract of S. aurita is a rich source of abietane diterpenes with excellent antioxidant and anti-diabetic activities that can be useful to modulate oxidative stress, and might possibly be excellent candidates for the management of diabetes. This is the first scientific report on the phytochemical isolation and biological evaluation of alpha-glucosidase and alpha-amylase inhibitory activities of Salvia aurita.

The increasing adoption of student-centred learning environs by the institutions of higher education in business, has led to new mechanisms and methodologies such as the Simulation-Based Learning (SBL), Problem-Based Learning (PBL) and Challenge-Based Learning (CBL). Literature has shown evidence of raising interest in these methodologies towards a more experiential paradigm with regard to upcoming events from the surrounding real-world context. This paper presents a Systematic Bibliographic Literature Review (SBLR) with respect to the integration and application of these innovative and collaborative methodologies in higher education. It aimed to identify its relevant advantages, challenges, and consequences for the future of business education. Bibliographic databases were searched for documents published up to May 2024 to categorize key topics discussed in the literature on SBL, PBL and CBL. The review process identified 89 empirical and non-empirical papers on SBL, PBL and CBL, business related paperwork, which resulted from the PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) method. PRISMA is a framework with evidence-based data designed to help authors perform a systematic literature review. Data analysis revealed diverse subthemes for those methodologies uses in business higher education institutions. The research questions “What are the advantages, challenges and implications of SBL, PBL and CBL altogether, in the training of business students?” guided the study. The central output of the research is the discovery of the varying uses of SBL, PBL and CBL overall, to cope with diverse demands arising within environmental context. Future research directions are suggested.

Due to the optical properties of the Electron Transport Layer (ETL) and Hole Transport Layer (HTL), inverted perovskite solar cells can perform better than traditional perovskite solar cells. It is essential to compare both types to understand their efficiencies. In this article, we studied inverted perovskite solar cells with NiOx/CH3NH3Pb3/ETL (ETL = MoO3, TiO2, ZnO) structures. Our results showed that the optimal thickness of NiOx is 80 nm for all structures. The optimal perovskite thickness is 600 nm for solar cells with ZnO and MoO3, and 800 nm for those with TiO2. For the ETLs, the best thicknesses are 100 nm for ZnO, 80 nm for MoO3, and 60 nm for TiO2. We found that the efficiencies of inverted perovskite solar cells with ZnO, MoO3, and TiO2 as ETLs, and with optimal layer thicknesses, are 30.16%, 18.69%, and 35.21%, respectively. These efficiencies are 1.5%, 5.7%, and 1.5% higher than those of traditional perovskite solar cells. Our study highlights the potential of optimizing layer thicknesses in inverted perovskite solar cells to achieve higher efficiencies than traditional structures.

Epidermal Growth Factor Receptor (EGFR) tyrosine kinase is a cell surface receptor whose overexpression has been associated with different types of cancers including brain cancer (glioblastoma multiforme). The ability of the extract of Scutellaria baicalensis to inhibit the proliferation of malignant glioma cells have been reported. Thus, in this study we report the identification of 307 bioactive constituents responsible for the anti-glioblastoma multiforme effect from S. baicalensis using in silico studies such as molecular docking, binding free energy calculations, pharmacophore modelling, induced-fit docking, gene enrichment analysis, molecular dynamic simulations and ADMET predictions. A total of 307 chemical constituents of S. baicalensis were screened and the top 10 scoring compounds indicated different binding affinities ranging from -9.010 to -6.427 kcal/mol towards the EGFR tyrosine kinase; Ganhuangenin, 5,7,2',5'-tetrahydroxyflavone, (2R)-2-(2,6-dihydroxyphenyl)-3,4-dihydro-2H-chromene-5,7-diol, and tenaxin I possess higher binding affinities (-9.010 to -8.649 kcal/mol) compared to the standard ligand, erlotinib having -8.539 kcal/mol. The compounds interacted with amino acids of clinical importance such as MET 769, GLU 738, THR 766 via H-bond. The structural features involved in the interaction with the target were mostly two aromatic rings, H-bond donors and acceptors and some hydrophobic interactions which varies between the ligands. Better docking scores in the induced-fit docking further validates the inhibitory potential of the compounds against the flexible protein. All the top-scoring ligands from S. baicalensis had zero Lipinski violation and also obeyed other drug-likeness rules by Ghose, Veber, Egan, and Muegge with the exception of breviscapine. Interestingly, all the compounds are not likely to be hepatotoxic, mutagenic, or cytogenic, making them potentially safe as anti-cancer agents.

Cordia dichotoma Forst. (F. Boraginaceae) has been traditionally used for the management of a variety of human ailments. In our earlier work, the antidiabetic activity of methanolic bark extract of C. dichotoma (MECD) has been reported. In this paper, two flavonoid molecules were isolated (by column chromatography) and identified (by IR, NMR and Mass spectroscopy/spectrometry) from the MECD with an aim to investigate their antidiabetic effectiveness. Molecular docking and ADMET studies were carried out using AutoDock Vina software and Swiss ADME online tool, respectively. The isolated flavonoids were identified as 3,5,7,3’,4’-tetrahydroxy-4-methoxyflavanone-3-O-L-rhamnopyranoside and 5,7,3’-trihydroxy-4-methoxyflavanone-7-O-L-rhamnopyranoside (quercitrin). Docking and ADMET studies revealed the promising binding affinity of flavonoid molecules for human lysosomal alpha-glucosidase and human pancreatic alpha-amylase with acceptable ADMET properties. Based on computational studies, our study reports the antidiabetic potential of the isolated flavonoids with predictive pharmacokinetics profile.

Chemotherapy represents the most applied approach to cancer treatment. Owing to the frequent onset of chemoresistance and tumor relapses, there is an urgent need to discover novel and more effective anticancer drugs. In search for therapeutic alternatives to treat the cancer disease, a se-ries of hybrid pyrazolo[3,4-d]pyrimidin-4(5H)-ones tethered with hydrazide-hydrazones, 5a-h, was synthesized from condensation reaction of pyrazolopyrimidinone-hydrazide 4 with a series of arylaldehydes in EtOH, in acid catalysis. In vitro assessment of antiproliferative effects against MCF-7 breast cancer cells, unveiled that 5a, 5e, 5g, and 5h were the most effective compounds of the series and exerted their cytotoxic activity through apoptosis induction and G0/G1 phase cell-cycle arrest. To explore their mechanism at a molecular level, 5a, 5e, 5g, and 5h were evalu-ated for their binding interactions with two well-known anticancer targets, namely the epider-mal growth factor receptor (EGFR) and the G-quadruplex DNA structures. Molecular docking simulations highlighted high binding affinity of 5a, 5e, 5g, and 5h towards EGFR. CD experi-ments suggested 5a as a stabilizer agent of the G-quadruplex from the KRAS oncogene promot-er. In the light of these findings, we propose the pyrazolo-pyrimidinone scaffold bearing a hy-drazide-hydrazone moiety as a lead skeleton for designing novel anticancer compounds.

SARS-CoV2 (corona virus) has spread globally at an unprecedented rate; so far, increasing SARS-CoV2-infected individuals have been identified. Although the situation in China is improving and is currently under control, the outbreak in other countries and its pandemic management is only beginning to develop. Based on 154 SARS-CoV2 genome sequence analyses, we used receptor–ligand docking to identify one potential point mutation (V354F) on the spike structure which enhances spike binding to ACE2 receptors underlying potential super infection. Importantly, the V354F site on spike S1 had been identified in 5/10 infected French patients living in Paris, who sharing 100% identical SARS-CoV2 genomes. With Covid-19 cases increasing rapidly in France that could lead to a new explosion, we suggest that the French government should identify all potential super spreaders and treat them accordingly. In summary, our study provides on of the measures to avoid the potential second worldwide explosion of SARS-CoV2.

New class of triazinoindole bearing thiosemicarbazide (1-25) was synthesized and evaluated for α-glucosidase inhibitory potential. All synthesized analogues exhibited excellent inhibitory potential having IC50 values ranging from 1.30 ± 0.01 to 35.80 ± 0.80 µM when compared with the standard acarbose having IC50 value 38.60 ± 0.20 µM. Among series the analogues 1 and 23 was found the most potent having IC50 values 1.30 ± 0.05 and 1.30 ± 0.01 µM respectively. Structure activity relationship (SAR) was mainly based upon by bring about difference of substituents on phenyl rings. To confirm the binding interactions, molecular docking study was performed. Synthesized analogues were characterized through HREI-MS, 1H and 13C-NMR analysis.

Nine 2-(1,2-benzothiazol-3-yl)-N-(4-oxo-2-phenyl-1,3-thiazolidin-3-yl) propanamides were designed and synthesized, combining benzisothiazole and 4-thiazolidinone in one frame. The aim of the study was to verify their effectiveness to contrast the inflammatory/oxidative process in which free oxygen and nitrite (ROS and RNS) radicals, advanced glycation products (AGEs), inflammatory cytokines and matrix metalloproteinases (MMPs) are involved. Docking studies of all the compounds were performed in order to explore their binding mode at the MMP-9 protein. An appreciable anti-inflammatory/wound healing effects of the tested compounds was highlighted. Derivative 23, bearing a 4-carboxyphenyl substituent at C2 of the 4-thiazolidinone ring, exhibited the highest activity, being able to inhibit MMP-9 at nanomolar level (IC₅₀ = 40 nM).

Childhood overweight/obesity (OV/OB) is a major public health problem, of greater concern when accompanied with comorbidities such as hypertension and insulin resistance leading to metabolically unhealthy obesity (MUO). Aetiologic associations between meal patterns, OV/OB risk and MUO are limited. The aim of this systematic review was to explore associations between meal patterns and the risk of childhood OV/OB and MUO. Longitudinal studies and randomised controlled trials from PUBMED and Scopus published between January 2013 - April 2024 were retrieved. Twenty-eight studies were included, all of which reported on OV/OB risk; none on MUO risk. Regular consumption of breakfast and family meals and avoiding dining while watching TV may be protective factors against childhood OV/OB, whereas meal skipping (primarily breakfast) may be a detrimental factor. Mixed effects of meal frequency on OV/OB risk were observed; no effects of frequency of lunch or of fast-food consumption and of meals served at school were found. There was insufficient evidence to support the role of other patterns (meal timing, eating in other social contexts). Meals were mainly participant-identified, leading to increased heterogeneity. Research focusing on childhood MUO and improved methodological approach (e.g. harmonised definitions) regarding the assessment of meal patterns are highly warranted.

Nowadays, unmanned vehicles are widely used in various fields. However, the safety of unmanned vehicles is directly determined by the autopilot systems, and sensor faults are a very critical factor that affects the normal operation of the autopilot systems. To efficiently and comprehensively test unmanned systems for sensor faults, this paper proposes a chip-level testing platform for unmanned vehicle autopilot systems based on FPGA hardware-in-the-loop simulation. Unlike existing testing platforms, the introduction of FPGA technology allows us to achieve nanosecond real-time simulation frequency, thus realizing chip-level simulation of sensors and black-box automated testing. Firstly, we propose a set of general platform and modeling methods, and the paper presents a detailed application of the four most common necessary sensors in autopilot systems as examples. Secondly, we propose for the first time a chip-level fault testing method for unmanned systems, and build a test platform with a quadrotor vehicle, the PX4 software platform, and the Pixhawk4 hardware platform as examples. Finally, the experimental results verify that the testing platform proposed in this paper can adapt to various autopilot systems and has high simulation test reliability.

The medium-voltage DC (MVDC) technology has gained increasing interests in recent years. Power electronics devices dominate those grids. Accurate simulation of such a grid, with detailed models of switching semiconductors, can quickly became very time-consuming, according to the number of connected devices to be simulated. A simulation approach based on interactions on a continuous time model can be very interesting, especially for developing a system level control model of such a modern MVDC distribution grid. Aim of this paper is to present all the steps required for obtaining a continuous time modelling of a +/- 10 kV MVDC grid case study, including Solid State Transformer (SST) and Modular Multilevel Converter (MMC) based Active Front End (AFE). Additional aim of this paper is to supply an educational content about the use of the continuous time simulation approach, thanks to a detailed description of the various devices modelled into the presented MVDC grid. The results of a certain number of simulation scenarios are eventually presented.

: Suicide is a serious public health problem, with a global mortality rate of 1.4% of all deaths worldwide, and the leading cause of unnatural death in Spain. The use of clinical simulation has proven to be a beneficial tool in the training of nursing students. Such experiences allow them to develop cognitive and affective skills that are fundamental for the detection of warning signs and use of interventions in cases of people who want to take their own lives. Working in a mental health environment can be difficult for nursing students; therefore, the purpose of this study was to explore the perceptions of nursing students on the approach, management and intervention of suicidal crisis through clinical mental health simulation. Methods: qualitative descriptive phenomenological study through focus groups and reflective narratives in a sample of 45 students. A thematic analysis was performed using ATLAS-ti. Results: After the analysis, three themes were obtained: (a) management and handling of emotions (b) identification of suicide motives (c) intervention in suicidal crisis. Discussion: Clinical simulation in mental health allows students to exercise clinical judgment reasoning, detect warning signs for a better treatment approach, and provide tools for effective intervention and management of patient care. The results of this study indicate that nursing students face challenges in approaching mental health clinical simulation due to lack of prior exposure.

As part of valorisation of agricultural waste into bioactive compounds, a series of structurally novel oleanolic acid ((3β-hydroxyolean-12-en-28-oic acid, OA-1)-phtalimidines (isoindolinones) conjugates 18a-v bearing 1,2,3-triazole moieties were designed and synthesized by treating a previously azide 4 prepared from OA-1 isolated from olive pomace (Olea europaea L.) with a wide range of propargylated phtalimidines using the Cu(I)-catalyzed click chemistry approach. OA-1 and its newly prepared analogues 18a-v were screened in vitro for their antibacterial activity against two Gram-positive bacteria, Staphylococcus aureus and Listeria monocytogenes; and two Gram-negative bacteria, Salmonella thyphimurium and Pseudomonas aeruginosa. Attractive results were obtained notably against L. monocytogenes. Compounds 18d, 18g and 18h exhibited the highest antibacterial activity when compared with OA-1 and other compounds in the series against tested pathogenic bacterial strains. Molecular docking study was performed to explore the binding mode of the most active derivatives against the target protein from L. monocytogenes. Results showed the importance of both hydrogen bonding and hydrophobic interactions with the target protein and are in favor to the experimental data.

This study aimed to solve the problems of sealing and tearing failure of packer’s rubber cylinders during CO2 downhole injection. Using the simulation software, Comsol, a rubber cylinder model in a supercritical CO2 (SC-CO2) environment was established. The thermal analogy method was used to simulate the CO2 diffusion and rubber cylinder swelling process, thus we analyzed the deformation and stress of the rubber cylinder caused by temperature, pressure and CO2 as swelling agent. Results showed that, in the SC-CO2 environment, under the influence of CO2 diffusion and the consequent swelling, the rubber cylinder body is prone to large deformation, and the maximum shear stress is significantly increased, leading to shear failure of the rubber cylinder. The reduction of the initial seating pressure can alleviate the impact of deformation, whereas the reduction of the maximum contact pressure could cause the rubber cylinder to lose its seal. We also analyzed the change rules between various factors and the maximum contact pressure of the rubber cylinder, which provides a theoretical basis and technical support for improving the sealing performance of the packer’s rubber cylinder in the SC-CO2 environment.

The paper explores the features of numerical simulation to analyze the dynamic behavior of drives controlled by pulse-width modulators. Modern motor control systems widely use pulse width modulation. Effective numerical modeling of such systems has specific features because the models employed are continuous-event and have hybrid behavior due to the presence of nonlinear links with discontinuities of the first kind. Therefore, it is essential to have special integration methods with variable steps, which should be factored in when developing the model. The paper shows how these problems are solved when modeling an electric drive with a DC motor in the SimInTech software.

This study delves into the realm of potential therapeutics for breast cancer by conducting a comprehensive docking simulation and virtual screening analysis using Autodock Vina Algorithm. The focus based on the human epidermal growth factor receptor 2 (HER2), a key protein associated with various cancers, particularly in the context of breast cancer.The results reveal compelling insights into the binding interactions of several natural compounds and drugs with HER2. Notably, Acebilustat, Bemcentinib, and Amentoflavone exhibit outstanding binding energies, averaging around -10 kcal/mol, suggesting strong and favorable interactions with the HER2 target.These encouraging findings not only emphasize the potential biological significance of these compounds but also hint at their potential usefulness in fighting breast cancer.Their promising binding affinities with HER2 position them as potential candidates for further investigation and development as therapeutic agents against breast cancer.

Mincle, a C-type lectin, is expressed predominantly in macrophages, where it plays a role in the macrophage response to various microorganisms such as mycobacteria. Docking is a computational procedure in which various software packages generate different positions at which ligands bind to their receptors. Discovery Studio docking was used in Molegro Virtual Studios. ChemDraw and ChemDraw3D were used for ligand preparation and construction because the protein preparation performed using docking software was a very lengthy process. Mincle plays a novel and non-redundant role in the induction of inflammatory signaling in response to mycobacteria. One disadvantage of Molegro studio docking is that it does not show the metallic atoms with which it interacts but rather shows hydrogen bonding and amino acid interactions. Hypothetically, trehalose dimycolate (TDM) and trehalose dibenzenate (TDB) detected by macrophages ultimately lead to CARD9 signaling, thereby producing pro-inflammatory cytokines and chemokines that have the potential to be used therapeutically.

G-protein coupled receptors (GPCRs) are large protein families known to be important in many cellular processes. They are well known for their allosteric activation mechanisms. They are drug targets for several FDA-approved drugs. We have investigated the diversity of the ligand binding site for these class of proteins against their cognate ligands using computational docking, even if their structures are known in the ligand-complexed form. The cognate ligand of some of these receptors dock at allosteric binding site, with better score than the binding at the conservative site. Further, ligands obtained from GLASS database, which consists of experimentally verified GPCR ligands, also show allosteric binding to GPCRs. The allosteric binders show strong affinity to the binding site, though the residues at the binding site are not conserved across GPCR subfamilies.