Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

In the development of the safety-critical systems, it is important to perform Failure Modes and Effects Analysis (FMEA) process to identify potential failures. However, traditional FMEA activities tend to be considered difficult and time-consuming tasks. To compensate for the difficulty of the FMEA task, various types of tools are used to increase the quality and the effectiveness of the FMEA reports. This paper explains an Automatic FMEA tool which integrates the Model-based Design (MBD), FMEA, and Simulated Fault Injection techniques in a single environment. The Automatic FMEA tool has the following advantages compared to the existing FMEA analysis tool. First, the Automatic FMEA tool automatically generates FMEA reports compared to the traditional spreadsheet-based FMEA tools. Second, the Automatic FMEA tool analyzes the causality between the failure modes and the failure effects by performing model-based fault injection simulation. In order to demonstrate the applicability of the Automatic FMEA, we used the electronic fuel injection system (EFI) Simulink model. The results of the Automatic FMEA were compared to that of the legacy FMEA.

In GDI engine applications, high-pressure (H.P.) injectors typically require to be designed to be capable of rapid response for GDI engines in order to be driven in the rapid response with respect to magnetic actuators, allowing for example more precise air-fuel ratio control in the GDI engines. The H.P. fuel injector is a highly dynamic component requiring careful voltage and pressure input modulation to achieve the required fuel injection quantities of GDI engines. The accurate fuel injection curves are a key influence for this technology, therefore will require the estimation of the fuel flow rate to be realized. In this paper, a PIC microchip for programming injector drive circuits is implemented to improve the performance of a H.P. fuel injector and tested to verify its feasibility. In the proposed injector drive circuit, powers MOSFETs directly control the charging/discharging current by a dsPIC30F4011 microchip. Design and analysis of the proposed injector drive circuit are presented. Next, effects of total pulse width, injector supply voltage, fuel system pressure and PWM operation on fuel injection quantities of a H.P. fuel injector are measured. Also, the measured data of the H.P. fuel injector fed by the injector driving circuit are defined as the fuel injection curves. Finally experimental results are provided for verification of the proposed injector drive circuit.

Maritime data not only identify financial resources that can significantly enhance the efficiency of shipping companies but also play a pivotal role in promoting eco-friendly and sustainable shipping practices. However, active corporate strategies are required to include maritime data essential for the commercial operation of autonomous ships in the form of corporate assets by transparent evaluating the data. The aim of this study is to review previous studies on da-ta-valuation models, identify a valuation model suitable for maritime business, consider the characteristics of maritime data. The analytic hierarchy process (AHP) method is used to derive priorities for valuing maritime data assets, with emphasis placed on the characteristics of mari-time data, followed by the character of the future-oriented maritime-data market and the da-ta-valuation model. The results obtained that the most important factors in selecting a maritime data-valuation model by analyzing the AHP method were identified as the characteristics of the maritime data(M1). The next most important factors analyzed were the features of the mari-time-data market(M2) and the features of the maritime data-valuation model(M3) in order. In addition, the characteristics of maritime data were preferentially considered among the main criteria, and the market approach (A2) was selected as the most optimal valuation model. The potential impact of this implementation could contribute to the establishment of an intelligent technology market by estimating the value of data and developing a platform for maritime data trading, allowing for more efficient data sharing and utilization by maritime autonomous sur-face ship(MASS).

With growing regulations on ship emissions, specifically carbon dioxide and nitrogen oxides, this study emphasizes the critical need for improving the performance of existing ship diesel engines. Focusing on easily modifiable injection conditions within the fuel system, the research aims to enhance combustion characteristics for operational ships. The study provides a concise analysis of the combustion performance improvements achievable in the field. The study employed a range of calculation conditions, spanning from fuel injection pressures of 20 MPa to 160 MPa, injection timing from 15 degrees before top dead center (BTDC) to 5 degrees after top dead center (ATDC), and spray angles varying between 10 degrees and 50 degrees. A comprehensive analysis was conducted, focusing on fuel distribution behavior, combustion dynamics, carbon monoxide (CO) production and extinction, as well as nitrogen oxide (NO) production. This thorough examination aimed to provide insights into the complex interplay of these factors in order to optimize combustion performance in ship diesel engines. The analysis indicated that substantial unburned fuel occurred at injection pressures below 40 MPa and spray angles less than 20 degrees. This issue was significantly mitigated when injection pressures exceeded 80 MPa or a spray angle of 40 degrees was employed. High flame propagation speeds were observed at injection pressures over 80 MPa and injection timings before BTDC 10. Carbon monoxide emissions were notably low when injection pressures exceeded 80 MPa and a 40-degree spray angle was used. Nitrogen oxide emissions were minimized under conditions of injection pressure below 40 MPa, injection timing after BTDC 5 degrees, and a spray angle between 30 and 40 degrees. The study concludes that the most effective injection conditions for concurrently reducing fuel consumption, minimizing incomplete combustion products, and lowering nitrogen oxide emissions in the target engine are optimal when the injection pressure is set at 80 MPa, the injection timing is positioned at 5 degrees before top dead center (BTDC), and the spray angle is maintained at 40 degrees.

The paper presents results from investigation focused on toxicity content in the exhaust gases emitted by the internal combustion compression ignition engine fueled with glycerol-ethanol blends at ratio of 50/50% by volume. Innovative issue of this engine is application of 2 high pressure injectors for glycerol-ethanol blend and diesel fuel direct injection at high pressure over 200 MPa. As known, glycerol is considered is by-product from biodiesel production technologies, hence its cost is relatively low to other renewable alternative fuels, which can be applied as a fuel to the reciprocating piston engines. Tests on exhaust gases toxicity were performed. It was found that the toxic components UHC, NOx and CO were below the maximal allowed limits. Both NOx and smoke emissions were strongly reduced with increase in glycerol-ethanol fraction in the fuel. Summarizing, such a fueling strategy proposed in this paper made it possible to effectively and environmentally friendly combust crude glycerol in the compression ignition engine working in a heat and power cogeneration unit. Exhaust gas emission tests conducted in this case confirmed usability of this technology to be implemented into practice.

Within the context of ever wider expansion of direct injection in spark ignition engines, this investigation was aimed at improved understanding of the correlation between fuel injection strategy and emission of nanoparticles. Measurements performed on a wall guided engine allowed identifying the mechanisms involved in the formation of carbonaceous structures during combustion and their evolution in the exhaust line. In-cylinder pressure was recorded in combination with cycle-resolved flame imaging, gaseous emissions and particle size distribution. This complete characterization was performed at three injection phasing settings, with butanol and commercial gasoline. Optical accessibility from below the combustion chamber, allowed visualization of diffusive flames induced by fuel deposits; these localized phenomena were correlated to observed changes in engine performance and pollutant species. With gasoline fueling, minor modifications were observed with respect to combustion parameters, when varying the start of injection. The alcohol, on the other hand, featured marked sensitivity to the fuel delivery strategy. Even though the start of injection was varied in a relatively narrow crank angle range during the intake stroke, significant differences were recorded, especially in the values of particle emissions. This was correlated to the fuel jet-wall interactions; the analysis of diffusive flames, their location and size confirmed the importance of liquid film formation in direct injection engines, especially at medium and high load.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

Diesel is consistently a very popular fuel for internal combustion engines. Its consumption in the European Union has been rising over recent years, as has the number of engines increasingly sensitive to fuel contamination. One of the most important parameters affecting diesel quality is water content. Although its exceedances of the standard’s permissible amount are not common, they carry the risk of serious damage to expensive, modern fuel injection systems. Current methods of measuring water content require both specialised personnel and equipment, as well as transporting the sample to a suitable laboratory. The research presented in this paper was aimed at verifying whether it would be possible to test the moisture content of diesel using impedance spectroscopy. Once refined, such measurement method could be used in situ. Analysing the properties of diesel is challenging, mainly because many types of the fuel are sold, the chemical composition of which is always a well-guarded manufacturer’s secret. The experimental results obtained on many types of commercially available diesel show that it is possible to use impedance spectroscopy to estimate the water content of different types of diesel fuel. The measurement accuracy achieved makes it possible to detect approaching or exceeding the permissible water content.

As marine traffic is contributing to pollution and mostly have predictable route with repetitive load profiles, to reduce their impact on environment, hybrid system with proton exchange membrane fuel cells (PEMFC-s) and battery pack, is promising replacement. For this purpose, the numerical model of repowered existing vessel that have two diesel engines with 300 kWe is developed. The goal of this paper is to develop numerical model which analyzes and determine equivalent hybrid ship propulsion system for known traveling route. The developed numerical model consists of an interconnected system with PEMFC stack and battery pack as power sources. Numerical model is developed and optimized to meet minimal required power demand for successful route demand, which has variable loads and daily sails six-time same voyage- in total 54 nautical miles. The results have shown that equivalent hybrid power system consists of 300 kWe PEMFC stack and battery pack with 424 kWh battery and state of charge varying between 20 and 87%. To power this new hybrid power system, hydrogen tank of 7200 l holding 284.7 kg at pressure of 700 bar is needed, compared to previous system that spend 1524 kg of diesel and generate 4886 kg of CO2.

Individuals with metabolic syndrome have increased risk for developing health conditions, in-cluding cardiovascular diseases and stroke. Modifiable risk factors, such as exercise and diet, are key components in the prevention and control of metabolic syndrome. Specifically, dietary pat-terns and habits are extremely successful in controlling more than one of the metabolic syn-drome risk factors. Meal timing and frequency have been associated with type 2 diabetes, cardi-ovascular diseases, and other chronic conditions. However, there is limited evidence linking metabolic syndrome to meal timing and meal frequency. This review summarizes and discusses how meal timing and frequency impact metabolic outcomes in adults.

Addressing the pressing challenge of global warming, reducing greenhouse gas emissions in the transportation sector is a critical imperative. Battery and fuel-cell electric vehicles have emerged as promising solutions for curbing emissions in this sector. In this study, we conducted a comprehensive life cycle assessment (LCA) for typical passenger vehicles, heavy duty trucks and city buses using either proton-exchange membrane fuel cells or Li-ion batteries with different cell chemistries. To ensure accuracy, we supplemented existing studies with data from the literature, particularly for the recycling phase, as database limitations were encountered. Our results highlight that fuel cell and battery systems exhibit large emissions in the production phase. Recycling can significantly offset some of these emissions, but a comparison of the technologies examined revealed considerable differences. Overall, battery electric vehicles consistently outperform fuel cell electric vehicles regarding absolute greenhouse gas emissions. Hence, we recommend prioritizing battery electric over fuel cell vehicles. However, deploying fuel cell electric vehicles could become attractive in a hydrogen economy scenario where other factors, e. g. the conversion and storage of surplus renewable electricity via electrolysis, become important.

Currently Single Board Computers (SBCs) are sufficiently powerful to run Real-Time Operating Systems (RTOSs) and applications with real-time attributes and requirements. SBCs serve as a foundation in Industrial Internet of Things (IIoT). The NXP Semiconductors produces a series of SBCs based on ARM-processors for a variety of industrial applications. The continuous increase in real-time data generated by IoT devices adds further research issues about the efficiency of such systems and applications. The purpose of this research was to investigate the timing performance of an NXP TWR-K70F120M device with μClinux OS on running concurrently tasks with real-time features and constraints. A custom-built multithreaded application with specific compute-intensive sorting and matrix operations was developed and applied to obtain measurements in specific timing metrics, including task’s execution time, threads waiting time, and response time, under different threads variations. The performance of this device was additionally benchmarked and validated against favorite platforms, a Raspberry Pi4 and BeagleBone AI SBCs. The experimental results showed that this device stands well both in terms of timing and efficiency metrics. Execution times were quite lower than the others, by approximately 56% in the case of two threads, and by 29% in the case of thirty-two threads configurations.

Dietary habits, including meal frequency, meal timing, and skipping meals, have been extensively studied due to their association with the development of non-communicable diseases (NCDs). This study describes dietary habits, meal timing, meal frequency, skipping meals, and late-night eating in Kuwaiti adults. The Kuwait National Nutrition Surveillance System data was utilized to reach the objectives of this study. The findings reveal that approximately 50% of the adults in Kuwait eat after 10 p.m., 29% skip breakfast, and 9.8% skip dinner. Furthermore, adults in Kuwait consume 4.4 meals per day on average. Women skip breakfast more often and have extended night fasting than men (p<0.001). Married adults skip breakfast and dinner less than unmarried adults (p<0.001). In conclusion, this descriptive study provides valuable insights into the dietary habits of Kuwaiti adults, emphasizing the importance of further investigating the association between meal timing, meal frequency, and the prevalence of NCDs in Kuwait.

With the widespread use of new equipment such as distributed photovoltaics, distributed energy storage, electric vehicles, and distributed wind power, the control of low-voltage distribution networks (LVDNs) has become increasingly complex. Acquiring the most recent topological structure is essential for conducting accurate analysis and real-time control of LVDNs. The signal-injection-based topology identification algorithm is favored for its speed and efficiency. This study proposes a new signal-injection-based topology identification algorithm aimed at solving the issues of reduced completeness and correctness of identification caused by missing feature signal records (FSRs). By analyzing the correlations between FSRs of different positions, the algorithm employs vertical and horizontal completion methods to effectively address missing data, combined with inclusion detection algorithms, to identify the topology of LVDNs. Based on the study of actual LVDN data, the results indicate that the algorithm not only significantly improves the completeness and correctness of topology identification for LVDNs but can also increase the number of devices in operation by evaluating the status of topological equipment, further enhancing the topology identification performance.

Scientific studies on the impact of wood species on solid fuel production, performance, and sustainability are grossly inadequate. The knowledge of this is imperative as users of solid fuels are increasing rapidly, especially in Africa. On this note, it becomes necessary to explore measures that will improve its efficiency and sustainability as an energy source. This study investigates some properties of selected wood species used as an energy source in Nigeria and their pelleting potential. Nine (9) samples were characterized and assessed for suitability of pelleting following four wood pellet quality standards. The findings revealed Anogeissus leiocarpus as the species with the best rating score in terms of fuel properties while Vitellaria paradoxa as the lowest. However, in terms of conformity with the four wood pellets standards, Khaya senegalensis, Parkia biglobosa and Anogeissus leiocarpus having presented density, calorific value, sulfur, arsenic, cadmium, and lead within the limits of the wood pellet quality standards were considered the best wood species in terms of fuel suitability and pelleting potential. The findings therefore suggest that not all wood species are suitable as fuel. Thus, for species that do not meet the standard wood pellet requirements, alternatives such as the use of biomass blends, additives, or process adjustments can be employed to adapt the quality to the standards or by using the fuels in improved cookstoves.

Development encompasses processes that occur at multiple length-scales, includ- ing gene regulatory interactions, cell movements and reorganisation, cell signalling and growth. It is essential that the timing of events in all of these different processes are coordinated to generate well patterned tissues and organs. However, how the timing of intrinsic cell state changes is coordinated with events at the multi-tissue and whole organism level is unknown. Here, we argue that an important mechanism which accounts for integration of timing across levels of organisation is provided by tissue tectonics: i.e. how morphogenetic events driving tissue shape change result in the relative displacement of signalling and responding tissues and coordinate devel- opmental timing across scales. In doing so, tissue tectonics provides a mechanism by which the cell specification events intrinsic to cells can be modulated by the temporal exposure to extracellular signals. This exposure is in turn regulated by higher-order properties of the embryo such as their physical properties, rates of growth and the combination of dynamic cell behaviours impacting tissue morphogenesis. Tissue tec- tonics creates a downward flow of information from higher to lower levels of biological organisation, providing an instance of downward causation in development.

The objective of this study is to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the equivalence ratio distributions and the injected fuel droplet behavior in the cylinder of the RCCI engine. The spray simulation was conducted by dividing two-part. First, the spray validation simulations progressed to find the spray-influenced factor of the test injector. Next, the engine simulations were performed with the spray-influenced factor obtained from spray validation simulations to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the injected fuel atomization and the equivalence ratio distributions. The introduced total heating value was fixed at 595J based on the lower heating value of diesel 14mg. The heating value of the premixed ethanol ratio varied from 0% to 40% based on the same total heating value in-cylinder in steps of 10%. It was revealed that when the premixed ethanol ratio based on the same total heating value in-cylinder was increased, the spray tip penetration value was reduced from the time after 4deg of diesel injection start because of the short injection duration by the small amount of diesel fuel. The SMD value was also more enormous up to 32.58% with increasing the premixed ethanol ratio because of the low kinetic energy of the injected fuel by the short injection duration and the slow evaporation of the injected fuel by the low cylinder temperature.

Controlling injection parameters is paramount when it comes to producing high-quality green parts using powder injection molding. This work combines experimental and numerical approaches to study the impact of injection parameters on mold in-cavity pressure and on the overall quality of green parts produced by low-pressure powder injection molding. The properties of two low-viscosity feedstocks (formulated from a water-atomized stainless-steel powder and wax-based binder system) were measured and implemented in an Autodesk Moldflow numerical model to quantify the molding pressures, which were finally validated using experimental real-scale injections. The results confirmed that an increase in mold temperature, an increase in feedstock temperature, and a decrease in solid loading decrease the mold in-cavity pressure, which was correlated with the feedstock viscosity. As a key result, real-scale injections confirmed that a minimum flow rate was required to avoid atypical high in-cavity pressure leading in several visual defects such as weld lines, flow marks, cracks, sinks, and incomplete filling. Due to differences in its thermal transfer properties, this flow rate threshold value decreases as the feedstock solid loading increases. For injection speeds higher than this value, the injection pressure measured experimentally was linearly correlated with the injection flow rate.

This study investigates whether a chronotherapeutic treatment of hepatocellular carcinoma (HCC) may improve treatment efficacy and mitigate side effects on healthy liver (HL). HCC was induced in Per2::luc mice which were irradiated at four time points of the day. Proliferation and DNA-double strand breaks were investigated in irradiated and non-irradiated organotypic slice culture (OSC) and ex vivo samples by detection of Ki67 and γ-H2AX. OSC proved useful to determine dose-dependent effects on proliferation and DNA damage but appeared unsuited to test the chronotherapeutic approach. Irradiation of ex vivo samples was most effective at the proliferation peaks in HCC at ZT02 (early inactivity phase) and ZT20 (late activity phase). Irradiation effects on HL were minimal at ZT20. Ex vivo samples revealed disruption in daily variation and down-regulation of all investigated clock genes except Per1 in non-irradiated HCC as compared with HL. Irradiation affected rhythmic clock gene expression in HL and HCC at all ZTs except at ZT20. Irradiation at ZT20 had no effect on total leukocyte numbers. Our results indicate ZT20 as the optimal time point for irradiation of HCC in mice. Translational studies are now needed to evaluate whether the late activity phase is the optimal time point for irradiation of HCC in man.

We analysed changes in magnitude and timing of the largest annual observed daily flow (Amax), in each water year, for 596 stations in high-value water resources catchments and flood risk locations across Australia. These stations are either included in the Bureau of Meteorology's Hydrologic Reference Stations, or used in its operational flood forecasting services. Monotonic trend (which are either consistently increasing or decreasing) analyses of the magnitude and timing of flood peaks (estimated using Amax) were performed using Theil-Sen and Mann-Kendell approach and circular statistics to identify strength of seasonality and timing. Regional significance at the drainage division scale was analysed using the Walker test. Monotonic decreasing trends in Amax flood magnitude were detected in the Murray-Darling River basin and in other drainage divisions in Victoria, south-west and mid-west of Western Australia and South Australia. No significant obvious pattern in Amax magnitude was detected in northern Queensland, coastal NSW, central Australia and Tasmania. Only the Tanami-Timor Sea Coast drainage division in northern Australia showed monotonic increasing trends. Monotonic trends in Amax magnitude were regionally significant at the drainage division scale. We found two distinct patterns in flood seasonality and timing. In the northern and southern parts of Australia, flood peaks generally occur during February to March and August to October, respectively. The strength of this seasonality varies across the country. Weaker seasonality was detected for locations in the Murray-Daring River basin, and stronger seasonality was evident in northern Australia, south-west of Western Australia, South Australia, Victoria and Tasmania. The trends of seasonality and timing reveal that in general, flood peaks are occurring later in the water year in recent years. In northern Australia, flood peaks are generally occurring earlier – at a rate of 12 days/decade. In Victoria, New South Wales and Tasmania, trends in timing are generally mixed. However, in the south-west of Western Australia, the largest change in timing was evident – with Amax peaks commencing later at a rate of 15 days/decade. Decadal variability in flood timing was found at the drainage division scale as well. Most stations show a decreasing trend in Amax magnitude, but how that trend is associated with the change in timing is not clear.

Annually, the oak forests of the Zagros Mountain chains, in western Iran and northeastern Iraq, face recurring challenges posed by forest fires, particularly in the Kurdo-Zagrosian forests situated in western Iran and northeastern Iraq. Assessing fire susceptibility relies significantly on vegetation condition. Integrating in situ data, Remote Sensing (RS) data, alongside the integration of Geographical Information Systems (GIS), presents a cost-effective and precise approach to capturing environmental conditions before, during, and after fire events, minimizing the need for extensive fieldwork. This study refines and applies the Zagros Grass Index (ZGI), a local vegetation index tailored to discern between grass-covered surfaces from tree canopies in Zagros forests, identifying the grass masses as the most flammable fuel type. Utilizing Moderate Resolution Imaging Spectroradiometer (MODIS) Normalized Difference Vegetation Index (NDVI) product as input, from 2013 to 2022, the ZGI aims to mitigate the influence of tree canopies, isolating NDVI values solely attributable to grass cover. By incorporating phenological characteristics of forest trees and grass species, the ZGI outperforms NDVI in mapping grass-covered areas that are crucial for fire susceptibility assessment in the study region. Results demonstrate a strong overlap between ZGI-based maps and recorded fire occurrences, validating the efficacy of the index in fire susceptibility estimation.

N-acetyl-L-cysteine (NAC), a sulfhydryl-containing compound, is mainly used as a mucolytic and as an antidote for acetaminophen overdose. Flow injection and sequential injection systems were designed and optimized with the aim of providing precise, accurate and reliable flow methods for NAC determination in pharmaceuticals with very low sample and reagent consumption. Proposed methods are based on a redox reaction wherein NAC reduces a complex of Cu(II) and bathocuproine disulfonate (BCS) to orange [Cu(BCS)2]3– complex, which absorption was measured at λmax = 483 nm. The optimized FIA and SIA configuration yielded a linear calibration curve with correlation coefficients (R2 = 0.9999 and R2 = 0.9996) in the concentration range of 3.0 × 10–7 – 3.0 × 10–5 mol L–1 and analytical frequency of 120 h–1 for the FIA method and 4.0 × 10–7 – 4.0 × 10–5 mol L–1, at sampling rate 60 h–1 for the SIA method. The proposed flow methods were successfully applied for the determination of NAC in pharmaceutical products, as the results showed good agreement with the standard method prescribed by Pharmacopoeia. Recoveries were in the range from 98.4% to 101.9% for the FIA method and from 97.2% to 101.8% for the SIA method.

Abstract: Background: epileptic encephalopathies (EE) are characterized by severe drug-resistant seizures, early-onset, and unfavorable developmental outcome. We describe a cohort of pediatric patients with EE who underwent intravenous methylprednisolone (IVMP) pulse therapy to examine its efficacy/tolerability. Methods: This is a retrospective study from 2020 to 2023. Inclusion criteria were: ≤18 years at the time of IVMP pulse therapy and at least 6 months of follow-up. Efficacy and outcome, defined as seizure reduction >50% (responder rate), were evaluated at 6 and 9 months of therapy, and 6 months after therapy suspension; quality of Life (QoL) was also assessed. Variables predicting positive post-IVMP outcomes were identified using statistical analysis. Results: Twenty-one patients were included. The responding rate was 85.7% at 6 and 9 months of therapy, and 80.9% at 6 months after therapy suspension. Genetic etiology and encephalopathy related to status epilepticus during NREM sleep (ESES) were predictive of efficacy (p=0.0475). The fourth month of therapy was the minimum time point to establish the effectiveness of the treatment. All patients showed improvements in QoL, EEG tracing and postural-motor development. No relevant adverse events were observed. Conclusions: Our study confirms the efficacy and tolerability of pulse IVMP treatment in pediatric patients with EE, especially with genetic etiology and ESES. The fourth month of therapy was the minimum time point to establish its effectiveness. QoL, EEG and postural-motor development also showed improvement.

Research on alternatives to rectal thermometry in canine and feline patients has focused on equipment and measurement location but not procedure duration. In a cross-over designed clinical scenario, we evaluated the time prior to and after (Pre-TempT and Post-TempT) rectal and axillary thermometry in canine (n = 114) and feline (n = 72) patients. Equipment duration was controlled for to determine a presumptive total time (TTime) associated with each thermometry method. Pre-TempT and TTime was significantly shorter in axillary thermometry trials for both canine and feline pets (P < 0.001). There was no difference in Post-TempT between thermometry methods in canine patients (P = 0.887) however, the Post-TempT was longer in felines after axillary thermometry (P = 0.004). Reductions in Pre-TempT and TTime were not significant in Scottish Fold breed cats and within the feline rectal trials, the TTime of domestic-long hair breeds was significantly longer than domestic-short hair breeds (P = 0.019). No other tested parameter played a significant role in these results. Axillary thermometry was faster than rectal thermometry in both canine and felines pets due primarily to the time associated with animal approach and restraint (Pre-TempT). These results have implications when optimizing clinic workflow, appointment durations and patient handling time.

The definition of Early Cholecystectomy (EC) is still debatable. This paper aims to find whether the timing of EC affects outcomes. This is a multicentric prospective observational study including patients with acute calculous cholecystitis (ACC) who had cholecystectomy within ten days from the onset of symptoms. Kruskall-Wallis test, Fisher’s Exact test and Spearman rank correlation were used for statistical analysis. The patients were divided into three groups depending on the timing of the operation: 0-3 days, 4-7 days, or 8-10 days from the onset of symptoms. 1117 patients were studied over a year. The time from the onset of symptoms to EC did not affect the postoperative complications and mortality, the conversion and the reintervention rate. It was a significant risk factor for intraoperative complications (0-3 days, 2.8%; 4-7 days, 5.6%; 8-10 days, 7.9%; p=0.01) and subtotal cholecystectomies (0-3 days, 2.7%; 4-7 days, 5.6%; 8-10 days, 10.9%; p&lt;0.001). ACC is an evolutive inflammatory process and, as the days go by, the local and systemic inflammation increases which makes surgery more complex and difficult with higher risk of intraoperative complications. We recommend performing EC for ACC as soon as possible within the first ten days of the onset of symptoms.

In the investment casting process, the pattern made of wax is obtained in a die for further formation of shell mold. This work investigates commercial pattern waxes fluidity with a newly developed injection fluidity test. A good correlation between wax fluidity and its viscosity is observed, which is different from metallic alloys, where the solidification behavior is more critical. The difference in investigated filled waxes fluidity can be associated with the type and amount of filler.

The aims of study was to evaluate the effects of rates, sources and timing of nitrogen application under cover of transgenic corn yield cultivated in Amazon Biome. The experiments were conducted in Parauapebas city, State of Pará, Brazil, in two years (2016/2017 and 2017/2018). The experimental design was randomized blocks, in a 5x2x2 factorial scheme, consisting of five rates of N (0; 45; 90; 135; and 180 kg ha-1), two nitrogen sources (urea and ammonium sulfate) and two application times of N (phenological stages V4 and V8), with four replications. The factor N rates promoted adjustment of linear equation (leaf area index, mass of thousand grains, and yield) and quadratic equation (dry mass of leaf index). Nitrogen fertilization promoted significant increases in mass of thousand grains and yield, obtaining the best results with 180 kg ha-1 of N applied at V4 phenological stage. Based on results obtained in two years of corn cultivated under conditions of Amazon Biome, the application of N at V4 phenological stage at rates of 121 to 131.39 kg ha-1 of N showed the best results for vegetative growth, while 180 kg ha-1 of N, regardless of source used, urea or ammonium sulfate, promoted greater grain weight and greater yield.

The study examined eating timing, diet, and the ratio of sleep phases in people with social jetlag (SJL). The study involved 83 participants who filled out a questionnaire, and 21 of them took part in the study of sleep phases by electroencephalography during the week. SJL was associated with a higher incidence rate of eating jetlag, eating phase delays, an increase in calorie intake after 9 p.m., a decrease in dietary fiber intake for breakfast, and melatonin-containing product consumption for dinner. Young people with SJL had a reduction in total sleep and light sleep phase duration by 60 and 36 min on work/school days and an increase in total sleep and REM sleep phase duration by 66 and 60 min on weekends, respectively. Young people consuming foods with more than 4234.5 ng of melatonin for dinner, compared with their peers consuming less than 313.2 ng of melatonin, showed a decrease in SJL and sleep debt by 54 and 90 min and an increase in the total sleep and the deep sleep phase duration by 66 and 30 min, respectively. Thus, the consumption of melatonin-containing foods for dinner is associated with a decrease in circadian misalignment and a sleep quality improvement.

In order to study the movement characteristics of fuel in the fuel tank during aircraft maneuvering, this paper conducts numerical simulations of a typical wing fuel tank using the finite point set method based on certain boundary conditions and excitation. The results show that the finite point set method can capture the complex phenomena of fuel free surface fluctuations, surging, rolling and breaking, as well as the change in center of gravity caused by fuel movement. Under aircraft acceleration and pitch angle excitation, fuel will generate sustained impact pressure on the fuel tank wall. The velocity attenuation of fuel flowing through the baffle communication hole is fast, and the flow resistance and energy dissipation of the communication hole buffer the impact of fuel on the fuel tank wall.

Repair mortar is commonly used to rehabilitate reinforced concrete structures or components that exhibit a relatively high level of distresses. Yet, this repair mortar can be contaminated by salt from its service environment. This work employs a two-dimensional finite element model to investigate the transport behavior of ionic species in salt-contaminated and water-saturated repair mortar under an externally applied electric field. The model was experimentally validated and then utilized to evaluate the effectiveness of electrochemical chloride extraction (ECE) with or without electrical injection of corrosion inhibitor (EICI). In the case study, both the ECE alone and the ECE+EICI treatment was found effective in decontaminating the zone in front of the steel rebar. In both techniques, the magnitude of current density has a significant effect on removing chloride out of the mortar and increasing the pH of the pore solution near the rebar, whereas the treatment time any not have a significant effect under some scenarios. The injection of the organic corrosion inhibitor significantly slowed down the removal of chloride. Changes in the ionic distribution in the mortar were generally beneficial in reducing the corrosion risk of the steel rebar and thus extending the service life of the repair mortar.

Background Main treatment modality for spinal meningiomas (SM) is gross total resection (GTR). However, optimal timing of surgery, especially in cases with absent or mild neurological symptoms remains unclear. The aim of this study is to assess the impact of early-stage resection on neurological outcome, quality of life (QoL) and quality of care. The primary objective was a favorable neurological outcome (McCormick scale 1); Methods: We retrospectively analyzed data from patients operated on SM between 2011 and 2021. Patients with mild neurological symptoms preoperatively (McCormick scale 1 and 2) were compared to those with more severe neurological symptoms (McCormick scale 3-5). Disabilities and QoL were assessed according to validated questionnaires (SF36, ODI, NDI). Results: Age, spinal cord edema, thoracic localization, and spinal canal occupancy ratio were associated with more severe neurological symptoms (all p<.05). Patients presented with mild symptoms were associated with favorable neurological outcome (OR: 14.778 (95%CI 3.918-55.746, p<.001), which is associated with shorter hospitalization, better QoL and less disabilities (p<.05). Quality of care was comparable in both cohorts; Conclusions: Early surgical intervention of SM, before the development of severe neurological deficits, should be considered as it is associated with a favorable neurological outcome and quality of life.

Background: Cleft lip and palate can affect the development of the maxilla, which may create a midfacial deficiency as well as an interference of the facial growth pattern and dentofacial esthetics. Objective: Estimate the chronological age of complete fusion of the spheno-occipital synchondrosis in cleft lip and/or palate patient´s and a control group, using cone beam computed tomography images. Methods: In this retrospective study, 125 patients were enrolled (cleft lip and/or palate group (n=91); control group (n=34)). Age comparison was made with Chi-square test and a Kaplan-Meyer analysis determined the median time to reach complete fusion of the spheno-occipital synchondrosis (p&lt;0.05). Results: The experimental group showed statistically significant differences in the median time for complete ossification between males and females (p=0.019). No statistically significant differences were found in the control group between males and females (p=0.104). The median time for complete ossification of the spheno-occipital synchondrosis was, for males, 15.0 years in both groups; for females, it was 14.0 years in the experimental group and 13.0 years in the control group. Conclusions: The present study showed no differences in the ossification of the spheno-occipital synchondrosis between individuals with and without cleft lip and/or palate.

High-quality ionization injection methods for Wake Field Acceleration driven by lasers or charged beams (LWFA/PWFA) can be optimised so as to generate high-brightness electron beams with tuneable duration in the attosecond range. We present a model of the minimum bunch duration obtainable with low-emittance ionization injection schemes, by spotting the roles of the ionization pulse duration, of the wake field longitudinal shape and of the delay of the ionization pulse position with respect to the node of the accelerating field. The model is tested for the resonant multi-pulse ionization injection (ReMPI) scheme, showing that bunches having length of about 300as can be obtained with a ionization pulse having duration of 30fs FWHM

Injection molding is one of the most common and effective manufacturing processes used to produce plastic products and impacts industries around the world. However, injection molding is a complex process that requires careful consideration of several key control variables. These variables and how they are utilized greatly affect the resulting parts of any molding operation. The bounds of the acceptable values of each control process variable or CPV must be analyzed and delimited to ensure manufacturing success and produce injected molded parts efficiently and effectively. One such method in which the key CPV of an injection molding operation can be delimited is through the development of a process window. Once developed, operating CPV at values inside the boundaries of the window or region will allow for the consistent production of parts that comply with the desired performance measures (PM), promoting a stable manufacturing process. This work proposes a method to experimentally develop process windows and illustrates the methodology with a specific molding operation.

Implementation of waterflood is with injected pressured water to reservoir to escalation oil production. Produced water is the dominated result from oil and gas mechanism in this world meanwhile 65% of water is injected back to the well for pressure maintenance, 30% for discharge aquifier condition and surface. For shaly sand, produced water usually bring coarse and suspended sand to the surface. Therefore, this sand level is needed to declining to avoid plugging in injection well until certain economic condition.

An important aspect of PET imaging in clinical application is the localization and detection of tumors and lesions by administering a predetermined amount of radiotracer. This allows for example, a detailed view of what is going inside the patient body in cellular level. The quality of PET image is strongly dependent on the amount of administrated radiotracer and the patient’s body parameters. As the amount of injection radiotracer increases, the quality of resulting image increases and the lesion detection efficiency increases. The PET examiner society recognizes that any dose of radiotracer is associated with some possible radiation risks. It can harmful to the patient if essential PET imaging session is not made due to fear of radiation risk. In order to ensure the highest quality diagnosis and the smallest radiation risk, the patient should receive the smallest amount of radiotracer that provide image with sufficient quality. Our study is focused on proposing an efficient PET simulation tool that predict the smallest possible amount of administrated radiotracer to provides the appropriate diagnostic information based on significant patient’s body parameters (weight, age) at fixed scanning to improve the clinical diagnostic process in term of tumor detecting and localization. We have built a model of particular PET scanner and model of patient based on real MRI image and digital anthropomorphic phantom of our region of interest (brain). We have performed Monte Carlo simulation for whole PET procedure with special parameter In evaluating stage, a dataset of 60 patient is used and 11 independent dose prediction simulation for each patient are performed. We conclude that our simulator perform a desirable and efficient prediction of injection radiotracer amount that optimizes the current clinical amount up to 28%. In addition, we found that the total injected radiotracer dosage for adult patients are mostly affected when considering patient weight rather than patient age.

Micro Injection molding combined with the use of removable inserts is one of the most promising manufacturing process for microfluidic devices, such as Lab-on-a-chip, that have the potential to revolutionize the healthcare and diagnosis system. In this work we have designed, fabricated and tested a compact and disposable plastic optical stretcher. To produce the mould inserts, two micro manufacturing technologies have been used. Micro Electro Discharge machining was used to reproduce the inverse of the capillary tube connection characterized by high aspect ratio. Thanks to the high accuracy of femtosecond laser machining, instead, we manufactured insert with perfectly aligned microfluidic channels and fiber slots, facilitating the final composition of the optical manipulation device. The optical stretcher operation is tested using microbeads and red blood cells solutions. The prototype presented in this work demonstrates the feasibility of this approach that should guarantee a real mass production of ready-to-use- Lab-on-a-chip.

Aquaculture contributes to the sustainable development of food security, marine resource conservation, and economy. Shifting aquaculture feed from fish meal and oil to terrestrial plant-derivatives may result in cost savings. However, many carnivorous fish cannot be sustained on plant-derived materials, necessitating the need for the identification of important factors for farmed fish growth and to investigate whether components derived from terrestrial plants can be used in feed. Herein, we focused on the carnivorous fish leopard coral grouper (P. leopardus) to identify the essential growth factors and clarify their intake timing from feeds. Furthermore, we evaluated the functionality of starch, which are easily produced by terrestrial plants. Results reveal that carbohydrates, which are not considered essential for carnivorous fish, can be introduced as a major part of artificial diet. The development of artificial feed using starch offers the possibility of increasing the growth of carnivorous fish in aquaculture.

Color can direct visual attention to specific locations through bottom-up and top-down mechanisms. Using Continuous Flash Suppression (CFS) as way to investigate the factors that gate access to consciousness, the current study investigated whether color also directly affected the timing of conscious perception. Low or high spatial frequency (SF) gratings with different orientations were shown as targets to the non-dominant eye of human participants. CFS patterns were presented at a rate of 10Hz to the dominant eye to delay conscious perception of the targets, and participants had the task to report the target’s orientation as soon as they could see it. With low-SF targets, two types of color-based effects became evident. First, when the targets and the CFS patterns had different colors, the targets entered consciousness faster than in trials where the targets and CFS patterns had the same color. Second, when participants searched for a specific target color, targets that matched these search settings entered consciousness faster compared to conditions where the target color was irrelevant and could vary from trial to trial. Thus, the current study demonstrates that color is a central feature of human perception and leads to faster conscious perception of visual stimuli through bottom-up and top-down attentional mechanisms.

Solid state sensors having timing capabilities are becoming an absolute need in particle tracking techniques of future experiments at colliders. In this sense, silicon sensors having 3D structure are becoming an interesting solution, due to their intrinsic speed and radiation resistance. A characteristics of such devices is the strict dependence of their performance on their geometric structure, which can be widely optimised by design, thus requiring suitable tools for an accurate modeling of their behaviour. This paper illustrates the development, performance and use of the TCoDe simulator, specifically dedicated to the fast simulation of carrier transportation phenomena in solid state sensors. Some examples of its effectiveness in the design and analysis of 3D sensors is also given.

The aim of this study was to assess the best timing to perform arthrocentesis in the management of temporomandibular disorders with regards to conservative treatment. A systematic search based on PRISMA guidelines, including a computer search with specific keywords, reference list search, and manual search was done. Relevant articles were selected after 3 search rounds for final review based on 6 predefined inclusion criteria, followed by a round of critical appraisal. Eleven publications, including 5 randomized controlled trials and 6 prospective clinical studies informed this review. The studies were divided into 3 groups based on the timing of arthrocentesis: 1). Arthrocentesis as the initial treatment, 2). Early arthrocentesis, and 3). Late arthrocentesis. Meta-analyses compared the efficacy of improvement in mouth opening and pain reduction in the 3 groups. The results were statistically significant and favoured early arthrocentesis, followed by late arthrocentesis in terms of both improvements in mouth opening and pain reduction. All 3 groups showed improvement in mouth opening and pain reduction. We conclude that early arthrocentesis may be able to produce the best clinical results, while arthrocentesis before attempting conservative treatment may produce less favourable outcomes.

Counterfeiting electronic components is a serious problem for the security and reliability of any electronic systems. Unfortunately, the number of counterfeit components has increased considerably after the introduction of horizontal semiconductor supply chain. In this paper, we propose a new method for detecting recycled Flash memory, a major target of the counterfeiters due to its ubiquitous usage. Proposed method is based on measurement of change in Flash array characteristics (such as erase time, program time, fail bit count, etc.) with its usage. We find that erase time is the best metric to distinguish a used Flash chip from a fresh one for the following reasons: (1) erase time shows minimal variation among different fresh memory blocks/chip and (2) erase time increases significantly with usage. We verify our method for a wide range of commercial off the shelf Flash chips from several vendors, technology nodes, storage density and storage type (single-bit per cell and multi-bit per cell). The minimum detectable chip usage varies from 0.05% to 3.0% of its total lifetime depending on the exact details of the chip.

The construction of optimized biological fuel cells requires a cathode which combines the longevity of a microbial catalyst with the power density of an enzymatic catalyst. Laccase secreting fungi were grown directly on the cathode of a biological fuel cell to facilitate the exchange of inactive enzymes with active enzymes with the goal of extending the lifetime of laccase cathodes. Additionally, a functionally graded coating was developed to increase enzyme loading at the cathode. Directly incorporating the laccase producing fungus at the cathode extends the operational lifetime of laccase cathodes while eliminating the need for frequent replenishment of the electrolyte. Additionally, the hybrid microbial-enzymatic cathode addresses the issue of enzyme inactivation by using the natural ability of fungi to exchange inactive laccases at the cathode with active laccases. Finally, enzyme adsorption was increased through the use of a functionally graded coating containing an optimized ratio of titanium dioxide nanoparticles and single walled carbon nanotubes. The hybrid microbial-enzymatic fuel cell combines the higher power density of enzymatic fuel cells with the longevity of microbial fuel cells and demonstrates the feasibility of a self-regenerating fuel cell in which inactive laccases are continuously exchanged with active laccases.

Sleep timing is one of the dimensions of sleep that refers to the time of day when sleep occurs. It was included in sleep-related research because of the potential associations between overweight and consumption of meals and snacks. This cross-sectional study aimed to investigate associations between sleep timing, meal and snack consumption, and weight status in 1333 schoolchildren aged 7-14 years. The midpoint of sleep was used as a sleep timing measure obtained by the midpoint between bedtime and wake-up time and classify as Early, intermediate, and Late. Schoolchildren in the Early group were less likely to be overweight (OR: 0.83, 95% CI 0.69; 0.99), had higher odds of mid-morning snack consumption (OR: 1.95, 95%CI 1.56; 2.44) and lower probability to consume the evening snack (OR: 0.75, 95%CI 0.59; 0.94) compared with the Intermediate group. The Late group had lower odds of mid-morning snack consumption (OR: 0.67, 95%CI 0.55, 0.80) than the Intermediate group. The consumption of mid-morning and evening snacks was associated with the Early and the Late midpoint of sleep. These results suggest that bedtime and wake-up time are relevant to consuming meals and snacks and may also be related to a greater probability of being overweight in children and adolescents.

Purpose: The intervertebral disc is a leading avascular organ in the body that may gather nutrition through diffusion. It maintains homeostasis by the use of autophagy and apoptosis to survive in unfavorable conditions such as stress and mechanical force. Therefore, excessive force and stress beyond normal conditions may cause intervertebral disc degeneration. The purpose of this study was to examine which is the better method, either external fixator (EF) or saline injection (SI), for inducing autophagy and apoptosis-mediated nucleus pulposus (NP) cell death in the discs of rat tail’s. Methods: Sixteen, nine-weeks-old male Sprague–Dawley rat tails were treated with 0.9% saline and EF (two-cross Kirschner wires) for a period ofsix and twelve weeks. Treated discs were dissected to identify the participation of autophagy and apoptosis in intervertebral disc degeneration. For identification purposes, H&amp;E staining, Masson’s trichrome staining, and immunohistochemistry (IHC) for LC3, beclin-1, and P62 in addition to MMP-2, MMP-3, and TIMP-1 were performed. Furthermore, we performed real-time polymerase chain reaction (RT-PCR) to observe autophagy-related gene expression (beclin-1, LC3, and P62) and apoptosis-related gene expression (MMP-2, MMP-3, and TIMP-1). Results: TheEF group showed more insidious NP cell degeneration than the control (Ctrl) group. Degeneration was elevated with increasing compression duration of EF group, whereas the SI group could not distinguish the margin of annulus fibrosus (AF) and NP cells. LC3, beclin-1, and P62 showed the highest and lateral expression whilst MMP-2, MMP-3, and TIMP-1 showed up-regulated and central expression in both groups, although the SI group could not recognize the boundary between NP and AF cells. The EF group showed the highest autophagy-related gene expression whereas the SI group showed lower expression. In addition, the EF group showed more autophagy-accumulating materials than the SI group which elevated with increasing compression duration. Furthermore, the SI group induced the highest apoptotic gene expression, but the EF group showed the lowest expression. Conclusion: The EF method was better for studying autophagy and apoptosis because it enhanced intervertebral disc degeneration after compression, which is actively linked to autophagy and apoptosis. The degeneration process was elevated by increasing the compression duration, but SI could not distinguish AF and NP cell margins.

Achieving synchronization between the central and peripheral body clocks is essential for ensuring optimal metabolic function. Meal timing is an emerging field of research that investigates the influence of eating patterns on our circadian rhythm, metabolism, and overall health. This narrative review examines the relationship between meal timing, circadian rhythm, clock genes, circadian hormones, and metabolic function. It analyzes existing literature and experimental data to explore the connection between mealtime, circadian rhythms, and metabolic processes. The available evidence highlights the importance of aligning mealtime with the body’s natural rhythms to promote metabolic health and prevent metabolic disorders. Specifically, studies show that consuming meals later in the day is associated with a elevated prevalence of metabolic disorders, while early time-restricted eating, such as having an early breakfast and an earlier dinner, improves levels of glucose in the blood and substrate oxidation. Circadian hormones, including cortisol and melatonin, interact with mealtimes and play vital roles in regulating metabolic processes. Cortisol, aligned with dawn in diurnal mammals, activates energy reserves, stimulates appetite, influences clock gene expression, and synchronizes peripheral clocks. Consuming meals during periods of elevated melatonin levels, specifically during the circadian night, has been correlated with potential implications for glucose tolerance. Understanding the mechanisms of central and peripheral clock synchronization, including genetics, interactions with chronotype, sleep duration, and hormonal changes, provides valuable insights for optimizing dietary strategies and timing. This knowledge contributes to improved overall health and well-being by aligning mealtime with the body’s natural circadian rhythm.

This paper examines the importance of choice of cooking fuels in wellbeing, analysing relationships between the proportion of population with primary reliance on different types of fuels for cooking (predictor variable), and key wellbeing indices (outcome variables) - Personal Health, Social Life, Civic Engagement, Life Evaluation, Negative Experience. By combining two global datasets from Gallup and WHO, the study adds to current evidence by taking a global perspective. Controlling for demographic factors such as income per capita, age, education level, employment, etc., regression modelling of these relationships show that clean cooking fuels are influential in all of the key wellbeing indices with the exception of the Life Evaluation Index. Among the key wellbeing indices, Personal Health and Negative Experience Indices are the most strongly influenced by choice of clean cooking fuels. By adding access to electricity as an additional predictor variable, the analysis highlights the potential for integrating eCooking into national electrification plans as part of sustainable energy transitions, given that health outcomes (Personal health and Negative experience indices) appear to be as closely linked to choice of cooking fuels as to access to electricity.

Microbial Fuel Cells (MFCs) representing a promising technology for the extract of energy and resources through wastewater and it also offer an economic solution to the problem of environment effluent and energy crisis in near future. The advance device is rather appealing, due its potential benefits, its practical application is, however hindered by several drawbacks, such an internally competing microbial reaction, and low power generation. This report is an endeavor to address various design connected to the MFCs application to wastewater treatment, in particular cost effective bioelectricity from waste water are reviewed and discussed with a multidisciplinary approach. The conclusions drawn herein can be of practical interest to all new researchers dealing with effluent wastewater treatment using MFCs.

The use of renewable fuels for internal combustion engines marks a significant stride towards sustainability in transportation and power generation. Ensuring the compatibility of these fuels with existing diesel engines and infrastructure is paramount for a smooth transition. Diesel engines ca-pable of harnessing the advantages of alternative fuels without extensive modifications offer a pragmatic approach to sustainable power for vehicles and industries. This article investigates the impact of carbon neutral renewable fuel types (HVOs and biodiesel) on the operation of the high-pressure injection pump, focusing on rotational speed and delivery pressure as key parame-ters. Investigations, based on pump operating cycle analysis and volumetric efficiency measure-ments, reveals that while speed dependence is moderate, fuel type significantly influences pump performance. Hydrogenated carbon-neutral fluids (HVOs) demonstrate adequate capabilities compared to conventional fossil fuels, offering promising prospects for reducing environmental impact. The findings underscore the importance of considering fuel properties, particularly com-pressibility modulus. These insights provide valuable guidance for the advancement of sustainable transportation and industrial systems.

Blade Health Monitoring (BHM) is often necessary in power plants and in aviation to prevent excessive blade vibration and cracks. This article proposes a network of blade tip timing sensors operated in a distributed BHM system. A number of cooperating agents is implemented in smart conditioning units which can autonomously operate in an adverse environment and communicate with other nodes via a serial interface. The project uses special versions of reduced instruction set chips that are able to operate near the hot section of the engine. Due to the limited number of types of microprocessors available in the extended temperature range grading, it was necessary to fully utilize the limited hardware resources and implement preemptive multitasking. For this purpose, a custom operating system and communication protocol were designed. The protocol hosts the middle layer which hides the implementation of the distributed system. The presented architecture ensures the sufficient computational capacity in individual nodes of the network operated in adverse conditions. It is scalable and resistant to transmission errors.

Nuclear waste is one of the most important environmental problems of nuclear power plants. A novel renewable distillation method has been proposed for an on-site recycling of the spent nuclear fuel and separation of its valuable components from the fissile isotopes, which is especially applicable for reactors using liquid fuels.

(1) Background: Substantial evidence that neural timing deficits are prevalent in developmental disorders, aging, and concussions resulting from a mild Traumatic Brain Injury (mTBI) is presented. We show that if timing deficits are remediated using low-level movement discrimination training, then high-level cognitive skills, including reading, attention, processing speed, and working memory improve substantially. (2) Methods: Two case studies are presented using MEG source imaging on an adult dyslexic, and a healthy older adult observed before and after training on movement discrimination two times/week for 8 weeks for adult dyslexic. (3) Results: We found improvements in reading, attention, processing speed, and working memory on neuropsychological tests. Substantial MEG signal increases in visual Motion Networks (V1, V3, MT, MST), Attention Networks (ACC, dlPFC, vlPFC and precuneous/ PCC areas) and Memory Networks (dlPFC). (4) Conclusions: Improving neural timing deficits before cognitive exercises to improve specific cognitive skills provides a rapid and effective method to improve cognitive skills. Improving the timing and sensitivity of low-level dorsal pathways, improving feedforward and feedback pathways, is essential to improve high-level cognitive skills. This adaptive training with substantial feedback shows cognitive transfer to tasks not trained on, significantly improving a person’s quality of life rapidly and effectively.

Exsolved perovskites can be obtained from lanthanum ferrites, such as La0.6Sr0.4Fe0.8Co0.2O3, as result of Ni doping and thermal treatments. Ni can be simply added to the perovskite by an incipient wetness method. Thermal treatments include calcination in air (e.g., 500 °C) and subsequent reduction in diluted H2 at 800 °C to favor the exsolution process. The chemistry of the nanoparticles exsoluted on the substrate surface can be further modulated by a post treatment in air. These processes allow to produce a two-phase material consisting of a Ruddlesden-Popper type structure and a solid oxide solution e.g. α-Fe100-y-zCoyNizOx oxide. The formed electro-catalyst shows sufficient electronic conductivity under reducing environment at the SOFC anode. Outstanding catalytic properties are observed for the direct oxidation of dry fuels in SOFCs, including H2, methane, syngas, methanol, glycerol and propane. This anode electrocatalyst can be combined with full density electrolyte based on Gadolinia-doped Ceria or with La0.8Sr0.2Ga0.8Mg0.2O3 (LSGM) or BaCe0.9Y0.1O3-δ (BYCO) to form a complete perovskite structure-based cell. Moreover, the exsolved perovskite can be used as a coating layer or catalytic pre-layer of a conventional Ni-YSZ anode. Beside the excellent catalytic activity, this material also shows proper durability and tolerance to sulphur poisoning. In this mini review, preparation methods, physico-chemical characteristics, surface properties of exsoluted and core-shell nanoparticles encapsulated on the metal-depleted perovskite substrate surface, electrochemical properties for the direct oxidation of dry fuels and related electrooxidation mechanisms are examined and discussed.

The high dependence on light crude oil as the main source of energy in automobiles., industrial processes, source of raw material for various industrial synthesis have made the heavy crude more available in the world and open for research work on its potentials as a source of energy for the increasing population of the world in areas like energy source for powering big marine engines, energy source in heavy industrial machines e.t.c. Though the relatively unfavourable characteristics of heavy fuel oil such as; high viscosity, high probability of precipitating is a reasonable challenge to the possible utilization of heavy fuel as a source of energy in the areas highlighted above. These issues of heavy fuel oil are largely due to the presence of Asphaltene in it which is a large complex hydrocarbon in heavy fuel oil. Understanding the combustion potential of asphaltene is therefore an interesting and challenging problem that has attracted increasing attention from both academia and industry. This research work is aimed at carrying combustion studies on the Forcados (Ni-geria) heavy fuel fraction asphaltene HFFA extracted from Forcados crude Oil and examining its combustion characteristics with the view to examine it for future sweet heavy fuel generation for it source got low sulphur content, to ascertain the volatile composition, moisture and ash content. The HFFA extracted to determine physical characteristics of the HFFA extracted for fuel properties potentialities and this study was carried out to evaluate the chemical constituents of forcadous asphaltene lead-ing to the generaration of HFFA using GCMS. The Forcados asphaltene showed some good fuel properties when subjected to ce-tane number, API gravity, flash point and cloud point parameter test. Probing further with AAS for trace metal presence showed some high concentration on Chromium (Cr), Nickel (Ni), Iron (Fe), Lead (Pb), Cadmium (Cd), Copper (Cu), Manganese (Mn) and Zinc (Zn) indicating the potential for residual and soot formation after combus-tion. But still being a sweet asphaltene from Nigerian sweet crude source will be de-void of corrosive effect on machineries and heavy fuel engine if used to power it as in the case of high sulphur content in Venezuelan crude oil and some other world. The GCMS showed the decomposition of heavy crude asphaltene peaks and sig-naling the presence of heavy fuel fraction in the composition of the asphaltene while the FTIR and the UV-VIS identified the various functional groups in the compounds and the identification of signals that cannot be seen in the normal spectrum respec-tively.

Heat and power cogeneration plants based on fuel cells are interesting systems for energy- conversion at low environmental impact. Different fuel cells have been proposed, but experimental testing rigs are expensive and the development of commercial systems is time consuming if based on fully experimental activities. Furthermore, tight control of operation of fuel cells is compulsory to avoid damage, which must be based on accurate models, able to predict the cell behaviour and prevent stresses and shut-down. Some selected examples of steady state, dynamic and fluid dynamic modelling of different types of fuel cells are proposed, mainly PEMFC and SOFC type. The general ideas behind the thermodynamic, kinetic and transport description are recalled, with some examples of models derived for single cells, stacks and integrated power co-generation units.

This study investigated the influence of nutrient inputs and their timing on saffron yield and quality. The study was conducted from 2016 to 2020 and involved the application of eight different fertilization treatments at various stages of saffron growth. These treatments included single doses in Autumn (A), Winter (W), and Spring (S); double doses in Winter-Spring (AW), Autumn-Spring (AS), and Winter-Spring (WS); and a triple dose in Autumn-Winter-Spring (AWS). A control group (C) received no fertilizer. A compound fertilizer with a 15-15-15 composition was applied across all treatments, with nitrogen (N) rates of 67.5 kg/ha for single doses (A, W, S), 135 kg/ha for double doses (AWF, ASF, WSF), and 202.5 kg/ha for the triple dose (AWSF). Similar rates were applied for phosphorus (P) and potassium (K). The findings demonstrated that fertilization generally enhanced saffron attributes. The triple dose treatment yielded the most effective results. The timing of fertilization also played a crucial role, as split applications during different growth stages led to higher production especially winter fertilization. However, spring fertilization had limited impact due to decreased plant activity and reduced nutrient absorption during that period. Although the yield increased, the qualitative aspects of saffron, including color (crocin), taste (picrocrocin), and aroma (safranal), were not significantly influenced by the fertilization treatments. Nevertheless, these attributes remained within the natural limits defined by ISO-3632, indicating that fertilization practices did not compromise saffron quality. Our study highlights the significance of nutrient inputs and their timing in optimizing saffron yield. It provides valuable insights for developing efficient fertilization programs to enhance saffron production while preserving its quality characteristics.

Timely mitosis is critically important for the early embryo development. It is regulated by the activity of the ubiquitously conserved CDK1 kinase. The dynamics of CDK1 activation must be precisely controlled to assure physiologic and timely entry into mitosis. Recently, a known S-phase regulator CDC6 emerged as a key player in the mitotic CDK1 activation cascade in early embryonic divisions, operating together with Xic1 as a CDK1 inhibitor upstream of the Aurora A- and PLK1 kinases, both CDK1 activators. Herein we review the molecular mechanisms that underlie the control of the mitotic timing, with special emphasis on how CDC6/Xic1 function impacts CDK1 regulatory network. We focus on the presence of two independent mechanisms inhibiting the dynamics of CDK1 activation: Wee1/Myt1- and CDC6/Xic1-dependent, and how they cooperate with CDK1 activating mechanisms. As a result we propose a comprehensive model integrating CDC6/Xic1-dependent inhibition into the CDK1-activation cascade. The physiological dynamics of CDK1 activation appear to be tuned by the system of multiple inhibitors and activators and their integrated modulation ensures concomitantly both the robustness and certain flexibility of the control of this process. Identification of multiplied activators and inhibitors of CDK1 activation upon M-phase entry allows a better understanding of why cells divide at a specific time, and how the pathways involved in the timely regulation of the cell division are all integrated to precisely tune the control of mitotic events.

In Nitrate Vulnerable Zones (NVZ) site-specific techniques are needed to match N availability with durum wheat (Triticum turgidum subsp. durum Desf.) requirements. Enhanced-efficiency fertilizers (EEF) can improve efficient N supply and reduce leaching, thus contributing to sustainable agriculture. To study the effects of rates, sources and timings of nitrogen application, two-year field experiments were carried out at two Mediterranean NVZs of Central Italy (Pisa and Arezzo). The trial compared: i) two N rates: one based on the crop N requirements (NO), the other on the Action Programmes’ prescriptions of the two NVZ (NAP); ii) three N sources (urea, methylene urea (MU), and nitrification inhibitor (NI) 3,4-Dimethylpyrazole phosphate (DMPP); and two top-dressing timings (1st tiller visible and 1st node detectable). Grain yield and yield components were determined, together with N uptake. Results showed that: i) grain and biomass production were reduced with NAP at both locations; ii) urea performed better than slow-release fertilizers; iii) the best application time varied depending on N source and location: at Pisa enhanced-efficiency fertilizers achieved higher yields when applied earliest, while for urea the contrary was true; at Arezzo different N fertilizers showed similar performances between the two application timings. Different behaviors of top-dressing fertilizers at the two localities could be related to the diverse patterns of temperatures and rainfall. Therefore, optimal fertilization strategies vary according to environmental conditions.

Electrochemical energy conversion and storage is key for the use of regenerative energies at large scale. A thorough understanding of the individual components, such as the ion conducting membrane and the electrode layers, can be obtained with scattering techniques on atomit to molecular length scales. The largely heterogeneous electrode layers of High-Temperature Polymer Electrolyte Fuel Cells are studied in this work with small- and wide-angle neutron scattering at the same time with the iMATERIA diffractometer at the spallation neutron source at J-PARC, opening a view on structural properties on atomic to mesoscopic length scales.

Normally, the Nernst voltage calculated from the concentration of the reaction gas in the flow channel is considered to be the ideal voltage (reversible voltage) of the oxyhydrogen fuel cell, but actually it will cause a concentration gradient when the reaction gas flows from the flow channel through the gas diffusion layer to the catalyst layer. The Nernst voltage loss in fuel cells in most of the current literature is thought to be due to the difference in concentration of reaction gas in the flow channel and concentration of reaction gas on the catalyst layer at the time when the high net current density is generated. Based on the Butler-Volmer equation in oxyhydrogen fuel cell, this paper demonstrates that the Nernst voltage loss is caused by the concentration difference of reaction gas in flow channel and on the catalytic layer at the time when equilibrium potential (Galvanic potential) of each electrode is generated.

Fuel gas network (FGN) synthesis is a systematic method for reducing fresh fuel consumption in a chemical plant. In this work, we address the synthesis of fuel gas network using block superstructure originally proposed for process design and intensification (Demirel et.al. [1]). Instead of a classical source-pool-sink superstructure, we consider a superstructure with multiple feed and product streams. These blocks interact with each other through direct flows that connect a block with its adjacent blocks and through jump flows that connect a block with all blocks. The blocks with feed streams are viewed as fuel sources and the blocks with product streams are regarded as fuel sinks. Addition blocks can be added as pools when there exists intermediate operations among 9 source blocks and sink blocks. These blocks can be arranged in a I × J two-dimensional grid with I = 1 for problems without pools, or I = 2 for problems with pools. J is determined by the maximum number of pools/sinks. With this representation, we formulate fuel gas network synthesis problem as a mixed-integer nonlinear (MINLP) problem to optimally design a fuel gas network with minimal total annul cost. We present a real-life case study from LNG plant to demonstrate the capability of the proposed approach.

Gold occurrence Maljavr, located in amphibolite metamorphosed rocks in the Uragubsky greenstone belt, is the first gold prospect connected with conglomerates of Archean age, found in the Fennoscandian Shield. Gold mineralization is controlled by a series of lenses of altered rocks in biotite gneiss-metaconglomerate. The age of zircon from biotite gneiss in the zone of alteration is 2665±22 Ma, this is considered as the time of alteration processes. Biotite gneiss and altered rocks were later intruded by tourmaline granite pegmatite at 2508±7Ga, the pegmatite caused recrystallization of sulfide minerals in the altered rocks. Visible gold in association with bismuth minerals native bismuth, ehrigite (the second finding in the world), maldonite, bismuthinite, joseite-B, hedleyite was found exceptionally in polymineral inclusions in recrystallized arsenopyrite and löllingite. The age of pegmatite 2508±7Ma we regard as the time of formation of gold-bismuth mineralization. Geological position of the Maljavr occurrence, the linkage of gold mineralization with pegmatite, geochemical association Au-As-Se-Te-Bi in the mineralized rocks – all these characteristics correspond to intrusion-related gold deposits. Biotite gneiss-metaconglomerate, hosting the mineralized altered rocks, was the probable primary source of arsenic and gold for mineralization.

Social media addiction has attracted the attention of researchers especially during the COVID era because negative emotions generated from the pandemic may have increased social media addiction. The present study aimed to investigate the role of negative emotions and social media addiction on health problems during and after the COVID lockdown. A survey was conducted with 2926 participants aged between 25 and 45 years. The data collection period was between 2nd September and 13th October 2020. Partial Least Square Structural Equation Modeling was conducted for data analysis by controlling the respondents' working time, leisure time, gender, education, and age. Our study showed that social media addiction and time spent on social media impact health. Interestingly, while anxiety about COVID increased social media addiction, fear about COIVD reduced social media addiction. Also, long working hours contributed most to people’s health issues, and its impact on social media addiction and hours was much higher than negative emotions, where males faced more health challenges than females. The impacts of negative emotions generated by the COVID on social media addiction and health issues should be reconsidered. Government and employers' control of people's working time stress should prioritize solving social media addiction-related issues.

Photoplethysmography (PPG) is a simple-to-perform vascular optics measurement technique that can detect changes in blood volume in the microvascular tissue bed. Beat-to-beat analysis of the PPG waveform enables the study of the variability of pulse features such as amplitude and pulse arrival time (PAT), and when quantified in the time and frequency domains, has considerable potential to shed light on perfusion changes associated with peripheral arterial disease (PAD). In this pilot study innovative multi-site bilateral finger and toe PPG recordings from 43 healthy control subjects and 31 PAD subjects were compared (recordings each at least 5 minutes, collected in a warm temperature-controlled room). Beat-to-beat normalized amplitude and PAT variability was then quantified in the time-domain using SD and IQR measures and in the frequency-domain bilaterally using Magnitude Squared Coherence (MSC). Significantly reduced normalized amplitude variability (healthy control 0.0384 (IQR 0.0217-0.0744) vs PAD 0.0160 (0.0080-0.0338) (p<0.001) and significantly increased PAT variability (healthy control 0.0063 (0.0052-0.0086) vs PAD 0.0093 (0.0078-0.0144) (p<0.001) was demonstrated in PAD using the time-domain analysis. Frequency-domain analysis demonstrated significantly lower MSC values across a range of frequency bands for PAD patients. These changes suggest a loss of right-to-left body side coherence and cardiovascular control in PAD. This study has also demonstrated the feasibility of using these measurement and analysis methods in studies investigating multi-site PPG variability for a wide range of cardiac and vascular patient groups.

Purpose: Intervertebral disc is a leading avascular organ in the body. Hence, it may utilize autophagy and apoptosis to alive in unfavorable condition like stress and mechanical force. But excessive force and stress is a key cause to intervertebral disc degeneration (IVDD). Purpose of this study is to identify, external fixator (EF) and saline injection (SI) may induce autopahgy and apoptosis mediated nucleus pulposus (NP) cells death in rat tail’s disc and which method is better for studying autophagy and apoptosis. Methods: Sixteen 9-week-old male Sprague–Dawley rat tails were treated with 0.9% saline and EF (two-cross kirschner wires) for 6 weeks and 12 weeks as well. Treated discs were dissected for checking out participation of autopahgy and apoptosis to intervertebral disc degradation (IVDD). For identifying them, we performed H&E staining, Masson’s trichrome staining, and Immunohistochemistry (IHC) for LC3, Beclin-1and P62 as well as MMP-2, MMP-3 and TIMP-1.Furthermore, we performed quantitative polymerase chain reaction (qPCR)to check out autophagy related gene expression (beclin-1, LC3 and P62) and apoptosis related gene expression (MMP-2, MMP-3 and TIMP-1) respectively. Results: More insidious nucleus pulposus (NP) cell degeneration was indentified in (EF) group than in (Ctrl) control group. And rate of degradation was elevated with increasing duration of compression, but SI group cannot distinguish the margin of AF and NP cells. Highest along with lateral expression was found for LC3, Beclin-1, and P62 of both groups. Up-regulated and central expression was observed for MMP-2, MMP-3 and TIMP-1 of both groups, although SI group cannot recognize the margin between NP and AF cells. Utmost autophagy related gene expression was identified in EF group than in SI group. Besides, maximum autophagy accumulating materials was found in EF group than in SI group. And it was amplified along with increasing the duration of compression. Highest, apoptotic gene expression was observed in SI group, whereas, EF group showed lowest expression. Conclusion: External fixator (EF) method was better to study autophagy and apoptosis because it enhanced IVDD after compression which is actively linked with autophagy and apoptosis. Degeneration process was conversely proportional along with duration of compression. On contrary, saline injection (SI) could not distinguish AF and NP cell border.

Microgrids offer flexibility in power generation in a way of using multiple renewable energy sources. In the past few years, microgrids become a very active research area in terms of design and control strategies. Most of the microgrids use DC/DC converters to connect renewable energy sources to the load. In this paper, the simulation model of a DC microgrid with three different energy sources (Lithium-ion battery (LIB), photovoltaic (PV) array, and fuel cell) and external variant power load is built with MATLAB/Simulink and the simulative results show that the stability of DC microgrid can be guaranteed by the proposed maximum power point controller MPPT. The three energy sources are connected to the load through DC/DC converters, one for each. This type of topology ensures protection for each energy source as well as optimum stability at the load.

In this study, the physical properties of briquettes produced from two different biomass feedstocks (sawdust and date palm trunk) and different plastic wastes were investigated, without using any external binding agent. The biomass feedstocks were blended with different ratios of two WEEE plastics (halogen-free wire and print circuit boards (PCB)) and automotive shredder residues (ASR). The briquettes production is studied at different waste proportions (10-30%), pressures (22-67 MPa) and temperatures (room-130 ˚C). Physical properties as density and durability rating were measured, usually increasing with temperature. Palm trunk gave better results than sawdust in most cases, due to its moisture content and the extremely fine particles that are easily obtained.

Older adults with diabetes are at elevated risk of complications following hospitalization. Home health care services mitigate the risk of adverse events and facilitate a safe transition home. In the United States, when home health care services are prescribed, federal guidelines require they begin within two days of hospital discharge. This study examined the association between timing of home health care initiation and 30-day rehospitalization outcomes in a cohort of 786,734 Medicare beneficiaries following a diabetes-related index hospitalization. Of these patients, 26.6% were discharged to home health care. To evaluate the association between timing of home health care initiation and 30-day rehospitalizations, multivariate logistic regression models including patient demographics, clinical, geographic variables, and neighborhood socio-economic variables were used. Inverse probability-weighted propensity scores were incorporated into the analysis to account for potential confounding between the timing of home health care initiation and the outcome in the cohort. Compared to patients who received home health care within the recommended first two days, patients who received delayed services (3-7 days after discharge) had higher odds of rehospitalization (OR 1.28, 95% CI 1.25-1.32). Among patients who received late services (8-14 days after discharge), the odds of rehospitalization were four times greater than for patients receiving services within 2 days (OR 4.12, 95% CI 3.97-4.28). Timely initiation of home health care following diabetes-related hospitalizations is one strategy to improve outcomes.

Background: The reported associations between time to first antibiotic dose after hospital arrival and short-term mortality have varied in prior studies of CAP. It is unclear the benefit of early antibiotics in all patients given the risks of antibiotic overuse and misdiagnosis; Methods: A PubMed and Google Scholar search was performed to identify articles detailing the epidemiology, prognosis, diagnosis, and preliminary management of CAP; Results: In sepsis, antibiotics should not be delayed, and should be administered as soon as possible after recognition. For moderate or severe CAP patients without sepsis, antibiotics should be administered as soon as the diagnosis of CAP is highly likely. For stable, non–critically ill patients with CAP, the timing of antibiotics is not as clear and available evidence does not recommend strict requirements. Antibiotic timing – both rapid and delayed could be used as indicators of quality care in differing clinical scenarios; Results: The dogma of starting antibiotics quickly, within a rigid timeframe of expectations and guidelines has not improved outcomes in pneumonia patients, and has led to an increase in antibiotic treatment in uninfected patients. Severity of illness is the key factor associated with poor outcomes and should more significantly guide the timing of antibiotic initiation.

Currently, most plastic waste stems from packaging materials, with a large proportion of this waste either discarded or used to derive fuel. Accordingly, there is growing interest in the use of pyrolysis in the context of chemically recycling non-recyclable (i.e., via mechanical means) plastic waste into petrochemical feedstock. The aim of this study is to use kinetic analyses to elucidate the pyrolytic properties of solid recovered fuel (SRF) produced using two types of reactors, namely, fixed bed and fluidized bed reactors. From the kinetic analysis, the activation energy corresponding to the rate of pyrolysis reaction conversion was obtained. In conclusion, we found that the pyrolysis occurs more vigorously in fluidized bed reactors compared to fixed bed reactors.

Ethanol produced from various biobased sources (bioethanol) has been gaining high attention lately due to its potential to cut down net emissions of carbon dioxide while reducing burgeoning world dependence on fossil fuels. Global ethanol production has increased more than six-fold from 18 billion liters at the turn of the century to 110 billion liters in 2019 (1,2). Sugar cane and corn have been used as the major feedstocks for ethanol production. Lignocellulosic biomass has recently been considered as another potential feedstock. This paper reviews recent developments and current status of commercial production of ethanol across the world. The review includes the ethanol production processes used for each type of feedstock, both currently practiced at commercial scale and newly developed technologies, and production trends in various regions and countries in the world.

The objective of this work is to compare how the gases emitted during the manufacture of the clinker vary in a cement plant, using two types of fuel: petroleum coke and unusable tires (UTs). The study is based on a case study using real time data on more than 40 process variables. Gases are analysed from two points of the production process: Sintering Kiln, main focus of emission to the atmosphere by chimney, and Preheater. The variation of CO and NOx depending on the oxygen and fuel type is studied. The SO2 levels are also analyzed, observing a decrease when using the UTs. The quality of the Clinker has been compared depending on the fuel type. The results are compared, on the one hand, with the quality of the clinker, determined by the content of the majority (C3S, Alite) and minority (Free CaO) phases, and, on the other hand, with the Kiln sintering temperature, the most influential parameter in the productive process. It is verified that Clinker quality is maintained, regardless of the type of fuel used. Concluding that the use of UTs as fuel can generate an important economic and environmental benefit for cement companies and their environment.

(1) Background: Benefits and timing of percutaneous dilatational tracheostomy (PDT) in Intensive Care Unit (ICU) COVID-19 patients are still controversial. PDT is considered a high risk procedure for transmission of SARS CoV-2 to health care workers (HCWs). The present study analyzed optimal timing of PDT, clinical outcomes of patients undergoing PDT and safety of HCWs performing PDT. (2) Methods: 133 COVID-19 patients underwent PDT in our ICU from April 1, 2020 to March 31, 2021, 23 patients were excluded and 110 patients were enrolled. A trained medical team was dedicated to the PDT procedure. Demographic, clinical history and outcome data were collected. Patients who underwent PDT were stratified into two groups: early group, PDT ≤ 12 days from orotracheal-intubation (OTI) and late group, &gt;12 days from OTI; HCW surveillance program was performed. (3) Results: Early group included 57 patients and late group included 53 patients. Early group patients showed shorter ICU length of stay and fewer days of mechanical ventilation than the late group (p&lt;0.001). At day 7 after tracheostomy, early group patients required fewer intravenous anesthetic drugs and experienced an improvement of ventilation parameters, PaO2/FiO2-Ratio, PEEP and FiO2 (p&lt;0.001). No difference in case fatality ratio between the two groups was reported. No SARS-CoV-2 infection was reported in HCWs performing PDT. (4) Conclusions: PDT was safe and effective for COVID-19 patients, since it improved respiratory support parameters, reduced ICU length of stay and duration of mechanical ventilation, and optimized the weaning process. The procedure was safe for all HCWs involved in the dedicated medical team. The development of standardized early PDT protocols should be implemented and PDT procedure could be considered as first line approach in ICU COVID-19 requiring prolonged mechanical ventilation.

A recent study published in Nature Medicine (Mautner et al., Nat Med 2023 Nov 2. doi: 10.1038/s41591-023-02632-w. Epub ahead of print) reported findings regarding a four-arm parallel, multicenter, single-blind, randomized, controlled clinical trial with 480 patients, aimed at comparing the therapeutic effectiveness of orthobiologic interventions against corticosteroid injections for the treatment of knee osteoarthritis (OA). The study concluded that, one-year post-treatment, all orthobiologic therapies examined were equivalent in effectiveness to each other and to corticosteroid injections. While we commend the scope and methodological rigor of the trial, the publication could be enhanced by a more comprehensive presentation of data to support the conclusions drawn. Particularly, the omission of baseline data for primary outcomes, the missing context to evaluate absolute values, the lack of discussion regarding interindividual variability, and the unexpectedly favorable results for corticosteroids that contrast the established literature, are areas that merit additional examination and insight. Here we aim to highlight these points for consideration, and advocate for the release of supplementary data to facilitate a comprehensive understanding and utilization of this rich dataset.

The influence of various energetic particles and electron injection on transport of minority carriers and non-equilibrium carrier recombination in Ga₂O₃ is summarized in this review. In Ga₂O₃ semiconductor, if robust p-type material and bipolar structures become available, diffusion length of minority carriers will be of critical significance. Diffusion length of minority carriers dictates functionality of such electronic devices as diodes, transistors, and detectors. One of the problems in ultra-wide band gap materials technology, is the short carrier diffusion length, due to scattering on extended defects. Electron injection in n- and p-type Gallium Oxide results in a significant increase of the diffusion length, even after its deterioration due to exposure to alpha- and proton-irradiation. Furthermore, post electron injection diffusion length in irradiated material exceeds that in Ga₂O₃ prior to irradiation and injection. The root cause of the electron injection-induced effect is attributed to the increase of minority carrier lifetime in the material due to trapping of non-equilibrium electrons on native point defects. It is, therefore, concluded that the electron injection is capable of “healing” the adverse impact of radiation in Ga₂O₃ and can be used for control of minority carrier transport and, therefore, device performance.

With the popularization of natural gas and the requirements for environmental protection, the development and utilization of natural gas is particularly important. The status of natural gas in China's oil and gas exploration and development is constantly improving, and the country is paying more and more attention to the exploitation and utilization of natural gas. The Upper Paleozoic tight sandstone in the Ordos Basin is characterized by low porosity, low permeability and large area of concealed gas reservoirs. By injecting CO2 into the formation, the recovery of natural gas can be improved, and at the same time, the stable storage of CO2 can be achieved to achieve a win-win situation of CO2 emission reduction and utilization. Injecting greenhouse gas CO2 into gas reservoirs for storage and improving recovery has also become a hot research issue. In order to improve the recovery efficiency of tight sandstone gas reservoir, this paper takes the complex tight sandstone of Upper Paleozoic in Ordos Basin as the research object, through indoor physical simulation experiments, carried out the influence of displacement rate, fracture dip angle, core permeability, core dryness and wetness on CO2 gas displacement efficiency and storage efficiency, and analyzed the influence of different factors on CO2 gas displacement efficiency and storage efficiency to improve the recovery and storage efficiency. The research results show that under different conditions, when the CO2 injection pore volume is less than 1PV, the relationship between the CH4 recovery rate and the CO2 injection pore volume is linear, and the tilt angle is 45 °. When the CO2 injection pore volume exceeds 1PV, the CH4 recovery rate increases slightly with the increase of displacement speed, the recovery rate of CO2 displacement CH4 is between 87% - 97%, and the CO2 breakthrough time is 0.7PV-0.9PV. In low-permeability and low-speed displacement cores, the diffusion of CO2 molecules is more significant. The lower the displacement speed is, the earlier the breakthrough time of CO2 is, and the final recovery of CH4 slightly decreases. Gravity has a great impact on CO2 storage and enhanced recovery. The breakthrough of high injection and low recovery of CO2 is earlier, and the recovery of CH4 is about 3.3% lower than that of low injection and high recovery. The bound water makes the displacement phase CO2 partially dissolved in the formation water, and the CO2 breakthrough lags about 0.1PV. Ultimately, CH4 recovery factor and CO2 storage rate are higher than those of dry core displacement. The research results provide theoretical data support for CO2 injection to improve recovery and storage efficiency in complex tight sandstone gas reservoirs.

The purpose of this study is to identify the steps involved in fabricating silica/chitosan composite membranes and their suitability in fuel cell application. It also intends to identify the physical characteristics of chitosan composite membranes, including their degree of water absorption, proton conductivity, methanol permeability, and functional groups. In this investigation, composite membranes were fabricated using the solution casting method with chitosan content of 5 g and silica variations dosage of 2% and 4% while stirring at a constant speed for 2h. According to the findings, the analysis of composite membranes produced chitosan membranes that were successfully modified with silica. The optimum membrane was found to be 4% s-SiO2 from the Sol-gel method with composite membrane's optimal condition of 0.234 cm/s proton conductivity, water uptake of 56.21%, and reduced methanol permeability of 0.99 × 10 -7 cm2/s in the first 30 minutes and 3.31 × 10-7 in the last 150 minutes. Maintaining lower water uptake capacity at higher silica content is still a challenge that needs to be addressed. However, the fabricated membranes showed exceptional results in terms of proton conductivity and methanol permeability.

A critical review of recent work on fuel lubricant interactions is undertaken. The work focusses on liquid fuels used in diesel and gasoline vehicles. The amount of fuel that contaminates the lubricant depends on driving conditions, engine design, fuel type and lubricant type. When fuel contaminates a lubricant, the viscosity of the lubricant will change (it will usually decrease), the sump oil level may increase, there may be a tendency for more sludge formation, there may be an impact on friction and wear, and low speed pre-ignition could occur. The increased use of biofuels (particularly biodiesel) may require a reduction in oil drain intervals, and fuel borne additives could contaminate the lubricant. The move to active regeneration of particulate filters by delayed fuel post-injection and the move to hybrid electric vehicles, and vehicles equipped with stop-start systems will lead to increased fuel dilution. This will be of more concern in diesel engines, since significant fuel dilution could still persist at sump oil temperatures in the range 100-150C (whereas in gasoline engines the more volatile gasoline fuel will have substantially evaporated at these temperatures). It is anticipated that more research into fuel lubricant interactions, particularly for diesel engines, will be needed in the near future.

Since World War I, the commercial aviation industry has seen many improvements that now allow people and goods to reach the other side of the world in few hours, consuming much less fuel than in recent decades. Improvements in cargo capacity and energy efficiency were significant and, in this scenario, commercial airlines were able to thrive and bring great benefits to world economy. However, this sector is facing environmental challenges due to the intensive use of aviation fuel. Brazil is one of the largest domestic air passenger markets in the world and still has great growth potential, considering its economic potential and territorial dimensions: roughly the same size as the US and twice the size of the European Union. This paper discusses partial productivity of jet fuel in Brazilian domestic aviation and proposes an econometric method to support public regulators and airlines decisions. The proposed model uses variables such as aircraft size, route characteristics and idle flight capacity in a panel data analysis. The results show that reducing idle capacity is one of the best ways to achieve better short-term fuel efficiency and therefore will reduce environmental impacts and have positive economic effects on commercial air transport activities.

Some global difficulties in the modern period include energy storage conversion. Researchers have looked to renewable energy resources to discover long-term answers to this dilemma. Fuel cells are one example of prospective energy producing technology. Although these technologies appear to be very enticing, they are known to be expensive due to high expenses. Catalyst costs, as well as concerns concerning energy density. Pt based Electrocatalysts have traditionally been used to drive ORR and offer efficient power outputs. However, cost constraints have limited the use of these electrocatalysts, rendering them inefficient. Apart from the high price, Pt-based Electrodes are prone to time-dependent drift and CO deactivation, both of which occur gradually. Electrocatalysts deteriorate over time, reducing the efficiency of fuel cells. This is why alternative electrocatalysts are in high demand for future energy applications. This review covers the comparative study of Platinium and Non-Platinium based electrocatalyst in fuel cells, their shortcomings and recent advancement for efficient and optimized electrocatalyst.

This study investigates the use of Au-doped Pd anodic electrocatalysts on ATO support for the conversion of methane to methanol. The study involves cyclic voltammetry, in-situ Raman spectra, polarization curves, and FTIR analysis to determine the optimal composition of gold and palladium for enhancing the conversion process. The results demonstrate the potential for utilizing methane as a feedstock for producing sustainable energy sources. Pd75Au25/ATO electrode exhibited the highest OCP value, and Pd50Au50/ATO had the highest methanol production value at a potential of 0.05 V. Therefore, it can be concluded that an optimal composition of gold and palladium exists to enhance the conversion of methane to methanol. The findings contribute to the development of efficient and sustainable energy sources, highlighting the importance of exploring alternative ways to produce methanol.

This article presents new PEM fuel cell models with hexagonal and pentagonal designs. After observing cell performance improvement in these models, we optimized them. Inlet pressure and temperature were used as input parameters, and consumption and output power were the target parameters of the multi-objective optimization algorithm. Then we used artificial intelligence techniques, including deep neural networks and polynomial regression, to model the data. Next, we employed the RSM (Response Surface Method) method to derive the target functions. Furthermore, we applied the NSGA-II multi-objective genetic algorithm to optimize the targets. Compared to the base model (Cubic), the optimized Pentagonal and Hexagonal models averagely increase the output current density by 21.819\% and 39.931\%, respectively.

This review summarises the main numerical models of fuel droplet heating and evaporation (DHE) in combustion engines across the different scales by accessing the nano/micro, meso and macroscopic fluid elements. The phenomena of multi-physics, multi-scale and multi-phase fluid flow and heat transfer are fully investigated when the fuel droplet (dodecane) is heating and evaporated into a background gas (nitrogen) crossing the liquid-vapour (LV) interface, kinetic region (i.e., Knudsen layer) and the bulk regions of liquid and gas in terms of molecular dynamics (MD) simulations, kinetic theory modelling (i.e., direct numerical solutions of Boltzmann equations) and convectional fluid dynamics approach, respectively. The evaporation coefficient of fuel evaporating molecules and their velocity distributions at the LV interface derived from MD simulations formulate a new kinetic boundary condition (KBC). Moreover, a novel kinetic model considering the inelastic collision between fuel molecules alongside the new KBC enables us to describe the non-equilibrium gas dynamics of fuel vapour and gas mixture in Knudsen layer (KL). Heat and mass flux analysis of the fuel droplet under combustion engine conditions can be accurately assessed by implementing the inelastic collision between fuel molecules in KL and a temperature-dependent evaporation coefficient at the LV interface into DHE. The surface temperature of fuel droplet and its evaporation time, which play a significant role in resolving the ignition delay and hence the combustion phasing in engines, can also be well estimated. The multi-scale modelling of fuel DHE will make significantly potential input into the cleaner engine targeting the low-carbon emissions and enhance the capability of the existing computational fluid dynamics (CFD) solvers.

The peri-urban and urban forests in Greece occupy a total area of 105.353 ha. In these vulnerable ecosystems, fire constitutes a natural disaster presenting particular challenges and specific difficulties. These include the high number of visitors as well as forests characteristics - such as the presence of particularly flammable tree species and high accumulation of combustible biomass – that make the on-start of fires more likely. The main purpose of the current research is to identify the optimum combination of silvicultural treatments to efficiently reduce potential forest fire severity and to facilitate their successful suppression by firefighting crews. In order to simulate the basic fire environment of urban forests, two main experimental plots were established and several tree and topographical characteristics were measured. Additionally, the NEXUS wildfire system was used to simulate forest fire potential behavior before and after the adoption of the silvicultural treatments that altered critical characteristics of the forest fire environment. The results clearly show that specific silvicultural prescriptions altered the type of forest fire spreading potential, revealing the overall efficiency of preventing actions during forest management.

In this study, a modular multi-step photometric microflow injection analysis (micro-FIA) system for the automatic determination of Cu(II) in a bioreactor has been developed. The system incorporates diverse 3D-printed modules, including a platform formed by a mixer module to mix Cu(II) with hydroxylamine which reduces Cu(II) to Cu(I) linked to a diluter module via a Tesla valve, a chelation mixer module, a disperser module, and a detector module provided by a LED light source at λ= 455 nm and a light dependence resistor (LDR) as a light intensity detector. The system measures the color intensity resulting from the chelation between Cu(I) and neocuproine. The micro-FIA system has demonstrated good capability for automatic and continuous Cu(II) determination, in a wide range of Cu concentrations from 34 to 2000 mg L-1. The device exhibits a good repeatability (coefficient of variation below 2% across the concentration range), good reproducibility, and has an accuracy of around 100% between 600 to 1900 mg·L-1. Real samples were analyzed using both the micro-FIA system and an atomic absorption spectroscopy method, revealing no statistically significant differences. Additionally, a Tesla valve located before the detector substituted a 3-way solenoid valve, eliminating the need for moving parts.

This study presents a novel approach to enhance Large Language Models (LLMs) like Alpaca by dynamically integrating real-time information. This method addresses the issue of content hallucination and data relevancy by automatically collecting and integrating current data from credible sources into model prompts. Experiments show a significant improvement in accuracy and a decrease in content hallucination, with a manageable increase in response time. The research underscores the potential of real-time data integration in making LLMs more accurate and contextually relevant, setting a foundation for future advancements in dynamic data processing in AI.

This work focuses on forced combustion with regards to the relationship between vent mixer models and several injection locations in unheated supersonic flow. A plasma jet torch was used to ignite the hydrogen–air mixture in a laboratory-scaled combustor duct. The flow field of the combustion was visualized with pressure and gas-sampling measurements. The vent mixers indicate good dispersion characteristics of the mixture for both parallel and normal 1 injections. However, forced combustion is dominantly governed by the injection rate toward the plasma jet (hot source) because the combustible region is restricted under the cold main flow. For this reason, the parallel injection, which provides the hydrogen–air mixture directly toward the plasma jet, shows good combustion performance. The normal 1 injection interacted with the vent mixers and shows slightly good combustion performance. Lastly, the normal 2 injection is little affected by the vent mixers and has poor combustion performance.

Coincident changes in abundance and behavior pose a challenge for interpreting abundance data from monitoring programs. In the San Francisco Estuary, long-term monitoring documented the declines of many species including the anadromous Longfin Smelt (Spirinchus thaleichthys). We identified seasonal patterns in reginal presence of Longfin Smelt through its life cycle using monitoring data and generalized additive modelling. We then investigated the year-to-year variability in the seasonal patterns of presence using functional data analysis (FDA). FDA separated the variability due to population size from variability due to differences in timing of presence. We found that Longfin Smelt have consistent seasonal distribution patterns and that two trawl types were needed to accurately describe those patterns. After accounting for variability due to year-class strength, shifts in the timing of presence were evident in three regions. The most variable period for the upstream regions Suisun Bay and West Delta was for age-0 fish in summer and for the downstream region Central Bay was for age-0 fish in late fall. This manifested as a delay in the typical fall re-occupation of upstream regions that comprise the study area for another monitoring study (Fall Midwater Trawl). Thus, a portion of the recent reductions in Fall Midwater Trawl abundance of Longfin Smelt resulted from changes in behavior rather than a decline in abundance. The presence of multiple monitoring surveys allowed analysis of distribution from one data set to aid interpretation of patterns in abundance from another monitoring survey. This study highlights how identifying portions of the life cycle with the most and least variability in distribution can help inform the types of management strategies that will be most effective. It also illustrates an analytical method that can be used to address the problem of confounded effects of abundance and behavior on patterns in monitoring data.

We have recently introduced the possibility of performing operando small-angle X-ray scattering measurements using a novel industrially relevant injection moulding system for plastics. We show that useful time-resolving measurements can be performed with a time-cycle of 1s and we highlight the possible steps to reduce this to 0.5s. We show how we can use the transmission measurements to provide a time-marker when plastic first enters the mould cavity in the region probed by the incident X-ray beam. We show the opportunities provided by this experimental stage mounted on the NCD-SWEET beamline at ALBA to probe the reproducibility of the injection moulding system on different scales. The design of the equipment allows the development of the structure and the morphology to be evaluated in different parts of mould cavity and we evaluate any differences in a rectangular mould cavity. We identify future prospects for this equipment in terms of novel mould heating and cooling systems and the opportunities for quantitatively evaluating radical approaches to injection moulding technology.

Minimum miscibility pressure (MMP) and oil swelling are two important factors of carbondioxide (CO₂) gas displacement mechanism occurred in the reservoir relate to application of CO₂ injection in the field to enhance oil recovery. In this paper determination of minimum miscibility pressure (MMP) between crude oil samples with carbondioxide gas conducted using two methods, i.e. correlation methods and laboratory experiment using slimtube. While, determination of swelling factor was conducted using PVT cell, where recombined fluid injected and conditionally at the reservoir temperature. The results of MMP using empirical equation (2807 Psig) and Holm & Josendal correlation (2750 Psig) is more approximate to the result of laboratory analysis (2805 Psig). The result of swelling test during injection CO₂ gas processes until 46.82% mole, shows that bubble point pressure is increasing gradually from 410 psig through 2200 psig, and swelling factor was also increase from 1.0 through 1.442. Based on the value of fracture pressure of Layer F in the KHL Field is 2200 Psig and MMP is 2805 Psig, hence the application of CO₂ gas injection in the field only could be conducted as immiscible flooding.

Safe sample transport is of great importance for infectious diseases diagnostics. Various treatments and buffers are used to inactivate pathogens in diagnostic samples. At the same time, adequate sample preservation, particularly of nucleic acids, is essential to allow an accurate laboratory diagnosis. For viruses with single-stranded RNA genomes of positive polarity, such as foot-and-mouth disease virus (FMDV), however, naked full-length viral RNA can itself be infectious. In order to assess the risk of infection from inactivated FMDV samples, two animal experiments were performed. In the first trial, six cattle were injected with FMDV RNA (isolate A22/IRQ/24/64) into the tongue epithelium. All animals developed clinical disease within two days and FMDV was reisolated from serum and saliva samples. In the second trial, another group of six cattle was exposed to FMDV RNA by instilling it on the tongue and spraying it into the nose. The animals were observed for 10 days after exposure. All animals remained clinically unremarkable and virus isolation as well as FMDV genome detection in serum and saliva were negative. No transfection reagent was used for any of the animal inoculations. In conclusion, cattle can be infected by injection with naked FMDV RNA, but not by non-invasive exposure to the RNA. Inactivated FMDV samples that contain full-length viral RNA carry only a negligible risk of infecting animals.

The present study evaluates the manufacturing parameters effects on the tensile properties of material composed by polylactic acid (PLA) with wood fibers known as Timberfill. The specimens were built through fused filament fabrication (FFF). The influence of four printing parameters (Layer height, Fill density, Printing velocity, and Orientation) are considered through a L27 Taguchi orthogonal array in order to reduce experimental runs. Tensile test is applied to obtain the response variable used as output results to perform the ANOVA calculations. Fill density is the most influential parameter on the tensile strength, followed by building orientation and layer height, whereas the printing velocity shows no significant influence. The optimal set of parameters and levels is found, being 75% fill density, 0○Z-axis orientation, 0.4 mm layer height, and 40 mm/s velocity as the best combination. Applying this combination showed 9.37 MPa in maximum tension. Lastly, five solid Timberfill specimens manufactured via injection molding technology were also tested and the results compared to the printed samples. The values of the elastic modulus, elastic limit, and maximum tension of the injected samples were almost twofold of those were obtained for the FFF samples, but the maximum elongation of injected specimens was fell sharply.

Intermediate temperature solid oxide fuel cell (SOFC) operation provides numerous advantages such as high combined heat and power (CHP) efficiency, potentially long-term materials stability, and the use of low-cost materials. However, due to the sluggish kinetics of the oxygen reduction reaction at intermediate temperature, the cathode of SOFC requires an efficient and stable catalyst. Significant progress in the development of cathode materials has been made over recent years. In this article, multiple strategies for improving the performance of cathode materials have been extensively reviewed such as A and B site doping of perovskites, infiltration of catalytic active materials, the use of core-shell composites, etc. Emphasis has been given to intrinsic properties such as thermal expansion compatibility, chemical and thermal stability, and oxygen transport number. Furthermore, to avoid any insulating phase formation at the cathode/electrolyte interface, strategies for interfacial layer modifications have also been extensively reviewed and summarized. Based on major technical challenges, future research directions have been proposed for efficient and stable intermediate temperature solid oxide fuel cell (SOFC) operation.

In response to global climate challenges and the increasing demand for energy, exploring renewable energy alternatives has become crucial. Bio-oils, derived from biomass pyrolysis, are emerging as potential replacements for fossil fuel-based liquid fuels. This paper shares findings from the Institute of Energy and Fuel Processing Technology on the quality of crude biomass pyrolysis bio-oil samples. These findings highlight their potential as motor liquid fuels. The article details the results of tests on the physicochemical properties of four distinct bio-oil samples. Additionally, it presents preliminary test results on the hydrodeoxygenation of bio-oils in a batch reactor. The production of homogeneous, stable mixtures using other fuel additives, such as diesel oil, rapeseed methyl ester (RME), and butanol, is also discussed.

: Microbial fuel cell (MFCs) devices utilise the metabolic processes of bacteria to generate electricity from various organic substrates. Due to the enormous amount of energy that organic waste produces, scientists are highly interested in advanced MFCs. MFCs serve as a multidisciplinary research platform at the engineering and natural sciences intersection. MFCs have various uses besides being used as energy sources, such as sensing capabilities. Despite showing considerable promise, only a few marine sediment MFCs have been deployed in real-world applications to supply current for low-power devices. It is now required to maintain track of the work being done by research groups worldwide and regularly compile significant discoveries due to the rising quantity of research publications. Review papers are a traditional beginning point for a literature review for new scholars. This review is a fast reckoner that directs readers to pertinent reviews and research publications detailing significant advances in microbial fuel cell research during the previous two decades. An overview of key advances in MFC research over the past two decades is provided as a quick reference in this review article. In addition, the report identifies research gaps that, if filled, could bring this technology closer to real-world use.

During the launch and return of a spacecraft, the intense combustion of propellants generates strong electromagnetic radiation, which interferes with the operation of electronic equipment in the spacecraft. To improve the electromagnetic compatibility of electronic equipment in spacecraft, it is necessary to study the electromagnetic radiation characteristics of rocket fuel. An electromagnetic radiation measurement system based on antennas is designed to measure the electromagnetic radiation generated by rocket fuel, and the electromagnetic radiation characteristics are obtained through data analysis. The mechanism of the electromagnetic radiation generated by rocket fuel is comprehensively analysed through the spatial, time-domain, frequency-domain, and energy-domain characteristics. A characterization model is established to provide a reliable scheme for evaluating the influence of rocket fuel electromagnetic radiation on electronic equipment in spacecraft.

Biofuels have become an integral part of everyday life in modern society. Bioethanol and fatty acid methyl esters are a common part of both the production of gasoline and diesel fuels. Also, pressure on replacing fossil fuels with bio-components is constantly growing. Waste vegetable fats can be replacing biodiesel. HVO seems to be a better alternative. This fuel has a higher oxidation stability for storage purposes, a lower temperature of loss of filterability for the winter time, a lower boiling point for cold starts and other. Viscosity, density, cold filter plugging point of fuel blend, and flash point were measured to confirm that a fuel from HVO is so close to a fuel standard that it is possible to use it in engines without modification. The objective of this article is to show the properties of different fuels with and without HVO admixtures and to prove the suitability of using HVO compared to FAME. HVO can also be prepared from waste materials and no major modifications of existing refinery facilities are required. No technology in either investment or engine adaptation of fuel oils is needed in fuel processing.

The use of biodiesel fuels in compression ignition engines leads to decrease CO, PM, HC and smoke opacity. However, NOx emissions increase importantly. Various methods to reduce NOx are used namely the EGR, the water injection method and the steam injection method. In this study, the steam injection method has been used instead of the other methods because of its benefits. This study examines the effects of steam injection on combustion products of diesel and biodiesel fuels by considering chemical equilibrium in order to determine the equilibrium combustion products involving 10 combustion products. A developed simulation code determing the equilibrium mole fractions and thermodynamic properties of combustion products is used for diesel and biodiesel fuels. It can be used for any fuel consisting of carbon, hydrogen or any oxygenated fuel. The results show that the mole fraction of CO2 and CO decrease with the steam injection ratios. NO mole fractions decrease with steam injection for lean mixtures but they increase slightly in the case of rich mixtures. The specific heat of combustion products increase with the steam injection ratios. Thus, the engine performance can be improved using the method. The model has been validated by comparing model results with the ones of NASA CEA software and GASEQ software using the methane as fuel. The relative errors of equilibrium mole fractions and thermodynamic properties of combustion products are less than 0.98 %.