This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Large-scale hydrological modeling in China is challenging given the sparse meteorological stations and large uncertainties associated with atmospheric forcing data.Here we introduce the development and use of the China Meteorological Assimilation Driving Datasets for the SWAT model (CMADS) in the Heihe River Basin(HRB) for improving hydrologic modeling, by leveraging the datasets from the China Meteorological Administration Land Data Assimilation System (CLDAS)(including climate data from nearly 40000 area encryption stations, 2700 national automatic weather stations, FengYun (FY) 2 satellite and radar stations). CMADS uses the Space Time Multiscale Analysis System (STMAS) to fuse data based on ECWMF ambient field and ensure data accuracy. In addition, compared with CLDAS, CMADS includes relative humidity and climate data of varied resolutions to drive hydrological models such as the Soil and Water Assessment Tool (SWAT) model. Here, we compared climate data from CMADS, Climate Forecast System Reanalysis (CFSR) and traditional weather station (TWS) climate forcing data and evaluatedtheir applicability for driving large scale hydrologic modeling with SWAT. In general, CMADS has higher accuracy than CFRS when evaluated against observations at TWS; CMADS also provides spatially continuous climate field to drive distributed hydrologic models, which is an important advantage over TWS climate data, particular in regions with sparse weather stations. Therefore, SWAT model simulations driven with CMADS and TWS achieved similar performances in terms of monthly and daily stream flow simulations, and both of them outperformed CFRS. For example, for the three hydrological stations (Ying Luoxia, Qilian Mountain, and ZhaMasheke) in the HRB at the monthly and daily Nash-Sutcliffe efficiency ranges of 0.75-0.95 and 0.58-0.78, respectively, which are much higher than corresponding efficiency statistics achieved with CFSR (monthly: 0.32-0.49 and daily: 0.26 – 0.45). The CMADS dataset is available free of charge and is expected to a valuable addition to the existing climate reanalysis datasets for deriving distributed hydrologic modeling in China and other countries in East Asia.

An atomic-scale approach is employed to simulate the formation of precipitates with different lattice misfits in the early stages of aging of supersaturated aluminum alloys. Simulation results reveal that the increase of lattice misfit could significantly promote the nucleation rate of precipitates, which results in a larger number and smaller size of the precipitates. The morphologies of the precipitates also vary with the degree of lattice misfit. Moreover, the higher the lattice misfit, the earlier the nucleation of the second phase occurs, which can substantially inhibit the movement of dislocations. The research on the lattice misfit of precipitation can provide theoretical guidance for the design of high-strength aluminum alloy.

During deep-sea mining, the heavy metals pollutants can cause contamination in the marine environment. In this paper, the multiphasic coupling model is established to describe the heavy metal migration process during deep-sea mining, which takes the effects of convection-diffusion, adsorption-desorption and sedimentation-resuspension of heavy metals in the aquatic environment into full consideration. Due to the advantages of Lattice Boltzmann method, it is adopted to numerically solve the multiphasic coupling model and achieve the simulation for heavy metal migration process during deep-sea mining. In addition, taking Cadmium as an example, the concentration variations are discussed and analyzed in detail. Based on the established model and Lattice Boltzmann method, the concentration distribution of heavy metals can be accurately described to provide the reasonable bases for the evaluation of marine environmental protection.

The liquid-vapor phase change lattice Boltzmann method is used to investigate the pinning-depinning mechanism of the contact line during droplet evaporation on the stripe-patterned surfaces in 3D space. Considering the curvature of the contact line and the direction of the unbalanced Young’s force, the local force balance theory near the stripe boundary is proposed to explain the steady state of the droplets on the stripe-patterned surfaces. An equation is proposed to evaluate the characteristic contact angle of the stabilized droplets. During the evaporation of the droplet, the stick-slip-jump behavior and the CCR-Mixed-CCA mode can be well captured by the lattice Boltzmann simulation. When the contact line is pinned to the stripe boundary, the contact line in the direction perpendicular to the stripes is slowly moving while the curvature of the contact line is gradually increasing. The gradually increasing curvature of the contact line accelerates the movement of the contact line, and the final contact line is detached from the stripe boundary. The research results provide theoretical support and guidance for the design, improvement and application of patterned surfaces in the field of micro-fluidic and evaporation heat transfer.

Crop production in Afghanistan suffers from limited phosphorus (P) availability, which severely hinders national agriculture sustainability. This present study hypothesized that deep fertilizer placement could significantly enhance uptake of immobile P and thus tissue P accumulation and crop yield. A two-year pot experiment growing two maize (Zea mays) hybrid cultivars (Xida-789 and Xida-211) was therefore conducted to test these hypotheses under three contrasting fertilizer placement methods (broadcast, side band, and deep band). In doing so, P concentrations in both maize tissues and soils were compared at 45, 60, and 115 days after sowing (DAS) under nine combinations of nitrogen (N) and P fertilizer rates (kg ha-1: N112P45, N112P60, N112P75, N150P45, N150P60, N150P75, N187P45, N187P60, N187P75). Results have shown that deep band placement significantly increased P uptake efficiency, leading to greater P concentration and accumulation in maize tissues compared to other two fertilization methods. This improved P uptake was attributed to several factors associated with deep placement, including reduced P fixation, enhanced root access to P, and moisture availability for P uptake. Additionally, deep band placement combined with higher N application rates (N187 and N150) further enhanced plant P uptake by promoting P availability and utilization mechanisms. Deep band placement also resulted in significantly higher total soil P, Olsen-P, and P use efficiency than broadcast and side band methods, indicating a more efficient P fertilization strategy for maize that can improve growth and yield. This present study also found positive correlations between P concentration in plant organs and soil Olsen-P, highlighting the importance of adequate soil P levels for optimal plant growth. Overall, our results have showed that deep band fertilizer placement emerged as a superior strategy for enhancing P uptake efficiency, utilization, and maize productivity compared to broadcast and side band placement. This approach can potentially optimize P fertilizer utilization, improve maize growth and yield, while minimizing environmental P losses associated with broadcast applications.

Conditions under which compositions of component systems form a well-defined system-of-systems here are formulated at a fundamental level. Statement of what defines a well-defined composition and sufficient conditions guaranteeing such a result offers insight into exemplars that can be found in special cases such as differential equation and discrete event systems. For any given global state of a composition, two requirements can be stated informally as: 1) the system can leave this state, i.e., there is at least one trajectory defined that starts from the state, and 2) the trajectory evolves over time without getting stuck at a point in time. Considered for every global state, these conditions determine whether the resultant is a well-defined system and if so, whether it is non-deterministic or deterministic. We formulate these questions within the framework of iterative specifications for mathematical system models that are shown to be behaviorally equivalent to the Discrete Event System Specification (DEVS) formalism. This formalization supports definitions and proofs of the afore-mentioned conditions. Implications are drawn at the fundamental level of existence where the emergence of a system from an assemblage of components can be characterized. We focus on systems with feedback coupling where existence and uniqueness of solutions is problematic.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

Lattice structures have emerged as promising materials for aerospace structures applications due to their high strength-to-weight ratios, customizable properties, and efficient use of materials. These properties make them at-tractive for use in anti-ice systems, where lightweight and heat exchanging are essential. This paper presents an extensive experimental investigation into mechanical compression properties of lattice trusses fabricated from AlSi10Mg powder alloy, a material commonly used in casted aerospace parts. The truss structures were manufactured using additive manufacturing Selective Laser Melting technique and subjected to uniaxial compressive loading to assess their performance. The results demonstrate that AlSi10Mg lattice trusses exhibit remarkable compressive strength with strong correlations depending upon both topology and cells’ parameters setup. The finding described highlights the potential of AlSi10Mg alloy as a promising material for custom truss fabrication, offering customizable cost-effective and lightweight solutions for aerospace market. The paper also emphasizes the role of additive manufacturing in producing complex structures with pointwise tailored mechanical properties.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

We develop an 1/n expansion method for the systematic approxi- mation of the solutions of classical spin systems (tri-dimensional vec- tors) which can describe general spin-spin interactions and phases with complex magnetization pattern. This method is applied to study the phase transitions observed in pyrochlore crystals (e.g. Gd₂ Ti₂ O₇ ) and the results have qualitative agreement with the experimental ones.

Susceptible, infective, recovered, and hospitalized/isolated individuals are placed on the cells of a nxn square lattice, where each cell is occupied by a single individual or is vacant. At discrete time units (typically one day each) all susceptibles and infectives execute a random movement and when a coincidence of the two types occurs the susceptible is converted to infective status according to some probability. Infectives are labelled by the number of days since originally infected. At each time increment the age label of the infectives is increased by one unit. When the label reaches a number like 15 or 20 days the susceptibles recover with some probability or become isolated/hospitalized. Upon reaching some age the latter types either recover or die. Probabilities for the movements and conversions from one status to another are implemented by random numbergeneration. Simulations were carried out to investigate the effect of several probability and age parameters, the size of population (proportional to nxn) and density (related to fraction of occupied cells), and the size of the movements. Mid-term gradual conversion of susceptibles to isolated was explored as intervention policy.

The aim of this work is to broaden the theory of computation by making use of fuzzy sets and multisets, which are generalization of ordinary sets. We study fuzzy multiset finite automata (FMFA), which are characterized by the incorporation of vagueness when it comes to the choice of the next state and multiple occurrences of the same input symbol. The resulting automaton is a genaralization of both classical automata and fuzzy automata. We discuss the algebraic characteristics of FMFA sub-automata—separatedness, strongly connectedness, cyclic, directable, and triangular FMFA in terms of equivalence classes induced by an equivalence relation defined on state set of FMFA. Intrestingly, for a given FMFA, a new FMFA can be constructed that is a homomorphic image of the original FMFA. We define different posets structures that can be associated with a given FMFA and show that some of them are upper semilattices and discuss the inter-relationship of a given poset, a finite upper semilattice (FUSL), a FMFA and a posets/FUSL associated with a given FMFA. Finally, we introduce the concept of decomposition of a FMFA in two different ways and characterize the strongly connected, triangular and directable FMFA.

This study examines geothermal energy extraction potential from the basement rock within the Denver-Julesburg (DJ) Basin, focusing on flow performance and heat extraction efficiency of different geothermal well configurations. It specifically compares U-Shaped, V-Shaped, Inclined V-Shaped, and Pipe-in-Pipe configurations against Enhanced Geothermal Systems (EGS) setups. Through numerical modeling, we evaluated the thermal behavior of these systems under various operational scenarios and fracture conditions. Results suggest that while closed-loop systems offer moderate temperature increases, EGS configurations show substantial potential for high-temperature extraction. This underscores the importance of evaluating well configurations in complex geological settings like the DJ Basin. The insights from this study aid in strategic geothermal energy planning and development, marking significant advancements in geothermal technology and setting a foundation for future explorations and optimizations.

The development of virtual models has recently been generalized in the field of complex mechatronic product design. Virtual models have various advantages such as: the systemic design approach, most often parametric, the implementation of extreme, expensive, and perhaps risky scenarios for the operation of the designed product, the testing of a large number of variants, etc. The main contribution of the paper consists of the development of an interface family called DeSeRoI (Dedicated Serial Robot Interface). Each member of the interface family integrates Simulink libraries and is created by the programmer in accordance with user requests. It follows that the interfaces composing the DeSeRoI family can have different levels of complexity depending on user needs and constraints. We are implementing a MATLAB-based application with user-provided configuration for serial robots in order to automatically visualize the kinematics data and simulation. Within MATLAB, two scripts are created responsible for generating Simulink models that compute the kinematics problem. One of the scripts (Main) saves information about the configuration of the robot and the other one (Generates_Simulink_Models) computes the kinematics problem. Different types of functions (software module) have been developed. Using these functions, the Simulink models result as modular entities. The automated approach eases user’s interaction and understanding of serial robots’ kinematics by performing the simulation procedure in a shorter amount of time and with higher efficiency, assuring a precise outcome despite the chosen parameters.

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

The majority of existing numerical simulations of the effect of bridge piers on water movement are based on a limited number of bridge piers at a laboratory scale. Furthermore, some 2D numerical simulations for actual bridge projects have deficiencies, including the use of overly large mesh sizes and an inadequate treatment of bridge piers. In this study, we compare three methods of structural mesh encryption, suspension mesh, and nonstructural mesh based on Delft3D, and apply the optimization scheme to a real bridge project. It is demonstrated that optimal results can be achieved by utilising a grid size comparable to the pier diameter (Dp) in the region away from the piers. In the vicinity of the piers, the grid cell size should be no larger than 1/9 Dp. The suspended grid technique (DD Boundary) can yield results consistent with those obtained using a full-area high-resolution grid, provided that the total number of grids can be reduced and the computational time is considerably reduced. In this study, the unstructured mesh (Deflt3D Flexible Mesh) scheme was unable to capture the oscillations of the wake flow behind the bridge piers. However, the application of the optimized scheme in bridge engineering has demonstrated its practical value. The findings of this study on mesh resolution and suspension mesh scheme can be applied to the Delft3D software and are also useful for other numerical simulation work.

In this paper we report a new development on the numerical model for aluminum-steam combustion. This model is based on diffusion flame of continuum regime and the thermal equilibrium between the particle and the flow field, which can be used to calculate the aluminum particle combustion model for two phase calculation conditions. The model prediction is in good agreement with the experimental data. A new type of vortex combustor was proposed for the combustion of aluminum and steam, and the mathematical model of the two phase reacting flow with in this combustor was established. The turbulence effects are modeled using the Reynolds Stress Model (RSM) with Linear Pressure-Strain approach, and the Eddy-Dissipation model is used to simulate the gas phase combustion. Aluminum particles are injected into the vortex combustor and form a swirling flow around the chamber and their trajectories are traced using the Discrete Phase Model (DPM). The simulation results show that the vortex combustor can achieve high efficient combustion of aluminum and steam. The influencing factors, such as the eccentric distance of the inlet of aluminum particles, particle size and steam inlet diameter, etc., are studied. The work described in this paper represents an attempt to the design of a vortex combustor in order to increase aluminum combustion efficiency.

Biomimicry in additive manufacturing often refers to topology optimization and the use of lattice structures, due to the organic shape of the topology-optimized designs, and the lattices often looking similar to many light-weight structures found in nature such as trabecular bone, wood, sponges, coral, to name a few. Real biomimetic design however involves the use of design principles taken in some way from natural systems. In this work we use a methodology whereby high resolution 3D analysis of a natural material with desirable properties is “reverse-engineered” and the design tested for the purpose. This allows more accurate replication of the desired properties, and adaption of the design parameters to the material used for production (which usually differs from the biological material). One such example is the impact-protective natural design of the glyptodont body armour. In this paper we report on the production of body armour models in metal (Ti4Al4V) and analyze the resulting mechanical properties, assessing their potential for impact protective applications. This is the first biomimetic study using metal additive manufacturing to date.

Master equations define the dynamics that govern the time evolution of various physical processes on lattices. In the continuum limit, master equations lead to Fokker-Planck partial differential equations that represent the dynamics of physical systems in continuous spaces. Over the last few decades, nonlinear Fokker-Planck equations have become very popular in condensed matter physics and in statistical physics. Numerical solutions of these equations require the use of discretization schemes. However, the discrete evolution equation obtained by the discretization of a Fokker-Planck partial differential equation depends on the specific discretization scheme. In general, the discretized form is different from the master equation that has generated the respective Fokker-Planck equation in the continuum limit. Therefore, the knowledge of the master equation associated with a given Fokker-Planck equation is extremely important for the correct numerical integration of the latter, since it provides a unique, physically motivated discretization scheme. This paper shows that the Kinetic Interaction Principle (KIP) that governs the particle kinetics of many body systems, introduced in [G. Kaniadakis, Physica A 296, 405 (2001)], univocally defines a very simple master equation that in the continuum limit yields the nonlinear Fokker-Planck equation in its most general form.

New q-series in the spirit of Jacobi have been found in a publication rst published in 1884 written in Russian and translated into English in 1928. This work was found by chance and appears to be almost totally unknown. From these entirely new q-series, fresh lattice sums have been discovered and are presented here.

The control of the fine particle emission from the coal-fired power plants has been a big challenge in china. Either the conventional electrostatic precipitator or the fabric filter has some shortages. The electrostatic precipitator is hard to keep high efficiency for the submicron particles. The fabric filter could keep high efficiency but with very high pressure drop. One solution is to combine them together. Several types of hybrid particle collectors (HPC) combining the electrostatic precipitator and the fabric filter together have been developed and applied in a number of projects in China. In recent years, numerical simulation technology has been widely used in the design of the collectors. In this paper, an unsteady numerical model is used to investigate the particle deposition characteristics in a scale hybrid collector. The fluid field is modeled by using incompressible Navier-Stokes equations with the RNG turbulence equations. The corona discharge is solved by using a finite volume method. The particle charging is modeled by using a filed-diffusing combined model. And an unsteady cake formation model is used to simulate the filtration process.

A modified Nambu{Jona-Lasinio Model with lattice structure is very instructive. It shows several similar problems and their solutions as the Lattice QCD. We study the limits of the large box size, small cell size and realistic pion mass. In particular, we study the relation of the discrete (bound state) solutions to the physical scattering states, for example the pion-pion scattering.

We report the strong coupling between plasmonic surface lattice resonances (SLRs) and photonic Fabry-Pérot (F-P) resonances in a microcavity embedded with two-dimensional periodic array of metal-insulator-metal nanopillars. For such a plasmonic-photonic system, we show that the SLR can be strongly coupled to the F-P resonances of both the odd- and even orders, and that the splitting energy reaches as high as 138 meV in the visible regime. We expect that this work will provide a new scheme for strong coupling between plasmonic and photonic modes.

Existing implants used with Total Knee Arthroplasty (TKA), Total Hip Arthroplasty (THA), and other joint reconstruction treatments, have displayed premature failures and frequent needs for revision surgery in recent years, particularly with young active patients who represent more than 55% of all joint reconstruction patients. Bone cement and stress shielding have been identified as the major reasons for premature joint failures. A breakdown of the cement may happen, and revision surgery may be needed because of the aseptic loosening. The significant mismatch of stiffness properties of patient trabecular bones and metallic implant materials in joint reconstruction surgery results in the stress shielding phenomenon. This could lead to significant bone resorption and increased risk of bone fracture and the aseptic loosening of implants. The present project introduces an approach for development of customized cellular structures to match the mechanical properties and architecture of human trabecular bone. It consists of four modules:1- characterization of geometry, microarchitecture, and stiffness properties of patient’s bones; 2- developing customized lattice structures tailored to mimic properties established in module 1; 3 - integration of developed lattice structure into full scale implant design and manufacturing; 4- implementation of the developed technology for use in implants that would overcome most of the issues related to aseptic loosening phenomenon. The present work aims at fulfilling the objectives of module 2 by exploring new designs of customized lattice structures and texture tailored to mimic closely patients’ bone anisotropic properties and that can incorporate an engineered biological press-fit fixation technique. The effects of various lattice design variables on mechanical performance of the structure are examined through systematic experimental plan using statistical design of experiments technique and analysis of variance method. All tested lattice designs were explored under realistic geometrical, biological, and manufacturing constraints. Of the four design factors examined in this study, strut thickness was found to have the highest percent contribution (41%) regarding the structure stiffness, followed by unit cell type, and cell size. Srut shape was found to have the lowest effect with only 11% contribution. The introduced solution offers lattice structure designs that can be adjusted to match bone stiffness distribution and promote bone ingrowth and hence eliminating the phenomenon of stress shielding while incorporating biological press-fit fixation technique.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

Shear dynamics simulation under extreme pressure was used to optimise the composition of ester-based lubricant base oil and extreme pressure additives. As a result, the ester-based lubricant in the weak-gel drilling fluid achieves reduction and increases the efficiency in drilling construction, and the field operation efficiency improves. The results of base oil lubrication simulation show that three base oils, namely, methyl oleate, ethyl oleate and butyl oleate, can be stably adsorbed on the surface layer of the shear surface. Methyl oleate has the lowest system temperature after shear stabilisation and has a high load-bearing capacity. The shear stress of methyl oleate decreases by changing the initial shear temperature and speed. It increases by 6.36 MPa when the speed increases from 10 m/s to 30 m/s. At this time, the shear stress of butyl oleate increases by 10.11 MPa. The results of the four-ball friction experiments show that the radius of the abrasion spot of methyl oleate is 179.83 μm, which is smaller than that of the other two base oils. Moreover, the friction coefficient of methyl oleate is 0.0018, which is approximately 1/3 of that of butyl oleate. Methyl oleate has better lubrication efficiency. The shear simulation results are consistent with the experimental results. The simulation can be used for the molecular design of lubricant materials. The oleic acid amide–containing amine group and the glyceride oleic–containing hydroxyl group were selected as the extreme pressure functional components for shear simulation. Results show that the shear stress of oleic acid amide is much lower than that of oleic acid glyceride when the initial shear temperature and speed change. The extreme pressure lubrication component–containing amine group is better than the extreme pressure lubrication material–containing hydroxyl group. The effects of different oleamide contents in the two-component mixtures on the lubricating properties were investigated through shear simulation, with methyl oleate as the base oil and oleamide as the extreme pressure functional component. The simulation results show that the lubricant has the optimal shear stress when 10% oleamide is added to the lubricant. The base properties of the lubricant were tested using a mixture of 90% methyl oleate and 10% oleamide, formulated as a lubricant. Results show that the friction coefficient can be reduced to 0.03 when 0.5% of the lubricant is added to the base mud. Moreover, the lubricant film formed shows high strength. Then, 1% lubricant was added to the weak-gel drilling fluid to evaluate the effect of the lubricant on the gel structure of the drilling fluid. Results show that adding lubricant does not affect the rheological properties of the drilling fluid. The gel structure of the system also remains stable even after 7 days of continuous ageing. The results of the field experiments in Hua3-01 well show that adding 1% ester-based lubricant to the field drilling fluid reduces the drilling friction by 33%. Thus, the efficiency of directional side drilling can be effectively improved, complicated accidents, such as poor starting and stopping of drilling and stuck jamming, can be avoided, and the goals of reducing quantity and increasing efficiency can be completed.

In this study, a new structure is proposed based on the body-centered cubic (BCC) lattice structure: adding a cubic truss in the center of the BCC structure, which is denoted by TLC (Truss-lattice-cube). The different dimensions of the central cube can affect the mechanical properties of the lattice structure notably. With a fixed length (15mm) of a unit cell, the optimal size for the central cube is determined to be 5 mm. Quasi-static compressive tests are performed on specimens made of Polylactic Acid (PLA) using additive manufacturing technology. The deformation characteristics of the new structure is analyzed in detail by experiments and numerical simulations. Compared to the BCC structure, the mechanical properties of the TLC structure are significantly improved. The initial flow stress of the TLC has been increased by 122% at a strain of 0.1; the specific strength has been enhanced by 293% at a strain of 0.5; and the specific energy absorption has been improved by 312% at the strain of 0.6. Printing defects in the lattice structure could deteriorate the mechanical property remarkably. In this work, incorporation of microcracks into the finite element model makes the simulation capture the influence of printing defects and improve the predictive accuracy of simulation significantly.

A typical vibrational spectrum in the ice phase has four separate bands: translation, libration, bending and stretching. Ice X, the final ice phase under high pressure, shows an exotic vibrational spectrum. Theoretically, an ideal crystal of ice X only has one peak at 998 cm-1 for Raman scattering and two peaks at 450 cm-1 and 1507 cm-1 for infrared absorption in this work. These three characteristic peaks are indicators of the phase transition between ice VII/VIII and ice X. Despite much experimental and theoretical work on ice X, only this study has clearly indicated these characteristic peaks in the region of the IR band. The phonon density of states shows quite different features than ice VIII, which could be verified by inelastic neutron scattering in the future. The dynamic processes of 15 vibrational normal modes are discussed and the typical hydrogen bonds are missing.

Over the past two decades, covalent organic frameworks (COFs) have become the most widely studied porous crystalline materials. Its specific physical and chemical properties are determined by the arrangement of atoms (crystal structure). Therefore, the determination of its structure is arguably the most important characterization step for COFs. Although single crystal X-ray diffraction (SCXRD) is the most widely used method for structure determination, the size of COF crystals is too small, or their crystal quality is so poor that confirmation of their structure is limited to lattice fringes by transmission electron microscopy (TEM). At present, many 2D-COFs have clear PXRD patterns, but not all 2D-COFs can obtain specific lattice fringes. This severely hinders the development of the COF field. Here, we discover the lattice shrinkage behavior of COFs under electron beam irradiation by comparing the lattice fringes of 2D-COFs under different conditions. By comparing the lattice fringes of TAPT-TFPT COF at room temperature and under liquid nitrogen freezing conditions, we found that the lattice fringes are in good agreement with the Powder X-ray diffraction (PXRD) and theoretical values of COF (2.213 nm) under freezing conditions, however, the lattice fringe spacing is only 1.656 nm at room temperature. The discovery not only provides new insights into the TEM characterization of COFs, but also further expands the range of crystalline COF materials.

Stabilization of planar premixed flame front on a lattice (porous) burner is considered. It is rigorously mathematically proved that there exist two different stabilization regimes: one with flame front located nearby the surface of the burner, and another with flame front located inside the lattice. These two regimes result in qualitatively different gas temperature profiles along the flow, that is monotonic and non-monotonic, respectively. Boundary between the two regimes is described in terms of dependence of the lattice solid material temperature on flow Peclet number. Likewise temperature profiles, such dependencies may be both monotonic and non-monotonic. Transition between the two types of dependencies is controlled by Arrhenius number. Conclusions of the study are supported by numerical analysis. They also compare favourably with available experimental data. Novelty of the present approach is fundamentally rigorous analytical analysis of the problem.

Real-time evolution of the electron densities under excitations in La₂CuO₄ was calculated by the time-dependent density functional theory (TDDFT). The author found, for the first time, under excitations, the electron cloud of Cu²⁺ changes obviously and the characteristic frequencies are 83 meV and 36 meV, respectively, for two different modes. The results are unexpected and close to that of lattice vibrations. The results show that the electron cloud of Cu²⁺ (just like the lattice) can be the electron-pairing medium in high temperature copper oxide superconductors.

By combing continuum topology optimization (TO) method and lattice structure technique, a sandwich aircraft spoiler with a high stiffness-to-weight is designed. TO method is served to produce the shell of the aircraft spoiler and the lattice structure, used as cores, is employed to support the shell. TO problem is established as maximizing the stiffness of the structure with limited material volume. Density-based method is utilized to achieve a 0/1 solution. We then empirically replace the core of the aircraft spoiler by using 3D kagome lattice structure. Two different materials, i.e., aluminum alloy and titanium alloy, are synthetically applied to further reduce the weight and simultaneously improve the strength of the aircraft spoiler. Numerical simulations are conducted to show that the designed aircraft spoiler can meet the service environment with a reduction of its weight by approximately 80% when compared with that of the initial design model. Finally, we have fabricated the designed model with photosensitive resin by using 3D printing technique.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

Two coupled climate models which participated the CMIP6 project (Coupled Model Intercomparison Project Phase 6), the Earth System Model of Chinese Academy of Sciences version 2 (CAS-ESM2-0) and the Nanjing University of Information Science and Technology Earth System Model version 3 (NESM3), were assessed in terms of the impact of four new sea ice parameterization schemes. These four new schemes are related to air-sea heat flux, radiation penetration and absorption, melt ponds, ice-ocean flux, respectively. To evaluate the effectiveness of these schemes, key sea ice variables with and without these new schemes, such as sea ice concentration (SIC) and sea ice thickness (SIT), were compared against observation and reanalysis product from 1980 to 2014. The simulations followed the design of historical experiments within the CMIP6 framework. The results revealed that both models demonstrated improvements in simulating Arctic SIC and SIT when the new parameterization schemes were implemented. The model bias of SIC in some marginal sea ice zones of Arctic was reduced, especially during March. The SIT was increased and the transpolar gradient of SIT was reproduced. The changes of spatial pattern of SIC and SIT after adding new schemes bear similarities between the two coupled models. This suggests that the new schemes have potential for broad application in climate models, especially for those with underestimated SIT.

Addressing the significant challenge in high-speed cotton dibbling operations in Xinjiang—specifically, the duck bill’s ("Duck bill" is a type of duck-billed bunch planting mechanism or component). shortened opening duration leading to seed throwing and floating—a new crawler-type delayed hole-forming mechanism has been designed. This mechanism extends the duck bill horizontally, thereby prolonging its opening time, enabling cotton sowing speeds of up to 6 km/h. Following agronomic principles for cotton planting, the overall layout of the crawler-type hole-forming mechanism, the structural parameters of the key components and the trajectory of the hole-forming are determined. We use the Discrete Element Method (DEM) and multi-body dynamics coupling method to simulate and analyze the motion process of the device. The fixed the tilt angle of the duck bill α(A), the depth of the duck bill hole-forming into the soil h(B), and the angle of rotation of the moving duck bill β(C) were taken as the experimental factors, with the longitudinal length of cotton seed hole (Y1) and the hole-forming depth of cotton seed hole (Y2) as the response values. The parameter range of each factor and the preliminary influence on the response value were determined through pre-experiments and single-factor simulation test. Based on RecurDyn-EDEM coupling, a quadratic regression orthogonal rotation combination simulation test was carried out. The results show that the order of the primary and secondary factors affecting the Y1 of the time-lapse hole-forming device was: A > C > B. The order of primary and secondary factors affecting the Y2 of the delayed hole forming device was: B > C > A. When the A was 2.4 °, the B was 42.4 mm, and the C was 30.5 °, the performance of the hole-forming was the best, and the Y1 was 26.4 mm, and the Y2 was 25.0 mm. The bench verification test results show that under the optimized combination of operating parameters, the average Y1 was 29.1 mm, and the average Y2 was 23.2 mm. Compared with the results of the previous coupled simulation model, the average relative errors of the two are 7.23 % and 4.36 %, respectively, indicating the accuracy and effectiveness of the established DEM simulation model and virtual test analysis. The hole-forming area and the opening time of the duck bill after the stable operation of the machine were recorded and measured. The calculated hole dislocation rate Hc was 4.33 %, which did not exceed the national standard requirement of 6 %. The qualified rate of hole distance Hx was 94.33 %, which was much higher than the national standard requirement of 80 %. The average opening time of the duck bill at a speed of 6 km/h is 0.45 s, which is much longer than the time required for cotton seeds to fall from the duck bill 0.11 s. It meets the requirements of high-speed cotton planting in China and facilitating advancements in future high-speed planter technology.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

The fractional advection-dispersion equation FADE plays an important role, especially in explaining the process of solute-transport in natural porous media with different degrees of heterogeneity. However, studies of the flow and transport of contaminants in the underground environment are based on the knowledge of many functional parameters of the subsoil. The delay factor caused by nonlinear absorption is one of these parameters inheriting significant ambiguities in its estimation in heterogeneous media. In the study, a fractional advection-dispersion FADE model was developed by the implicit Euler method, based on a Grunwald and Caputo-Liousville approximation to explicitly evaluate and simulate the transport mechanism of contaminants in media with unsaturated porous materials subjected to a nonlinear sorption model. Better solute mass retention was observed for fractional advection-dispersion FADE model. Moreover, the absorption parameter of the retardation coefficient has a better impact on the motion of the solute in a saturated porous medium. In other words, it has a significant effect on the dispersion of pollutants in aquifers. This study highlights the need to characterize the aquifer to predict solute transport in porous media.

The rapid development of quantum computing devices promises powerful machines with capabilities that solve a wide range of problems that traditional computers cannot. Therefore, quantum computers generate new threats at unprecedented speed and scale and specifically pose an enormous threat to encryption. Lattice-based cryptography is considered to be the rival to a quantum computer attack and the future of post-quantum cryptography. So, cryptographic protocols based on lattices have a variety of benefits, like security, efficiency, lower energy consumption, and speed. In this work, we study the most well-known lattice-based cryptosystems while a systematic evaluation and comparison is presented also, and focuses on their strengths and weaknesses.

The performance of lattice-Boltzmann solver implementations usually depends mainly on memory access patterns. Achieving high performance requires then complex code which handles careful data placement and ordering of memory transactions. In this work, we analyse the performance of an implementation based on a new approach called the data-oriented language, which allows the combining of complex memory access patterns with simple source code. As a use case, we present and provide the source code of a solver for D2Q9 lattice and show its performance on GTX Titan Xp GPU for dense and sparse geometries up to 4096 2 nodes. The obtained results are promising, around 1000 lines of code allowed us to achieve performance in the range of 0.6 to 0.7 of maximum theoretical memory bandwidth (over 2.5 and 5.0 GLUPS for double and single precision, respectively) for meshes of size above 1024 2 nodes, which is close to the current state-of-the-art. However, we also observed relatively high and sometimes difficult to predict overheads, especially for sparse data structures. The additional issue was also a rather long compilation, which extended the time of short simulations, and a lack of access to low-level optimisation mechanisms.

Tinnitus is a common phantom auditory percept, believed to be related to plastic changes in the brain due to hearing loss. However, tinnitus can also occur in absence of any clinical hearing loss. Then, since there is no hearing loss, the mechanisms that drive plastic changes remain largely enigmatic. Previous studies showed subtle differences in sound-evoked brain activity associated with tinnitus in subjects with tinnitus and otherwise, normal hearing, but the results are not consistent across studies. Here, we aim to investigate those differences using monaural rather than binaural stimuli. Sound-evoked responses were measured using functional magnetic resonance imaging (MRI) in participants with and without tinnitus. All participants had clinically normal audiograms. The stimuli were pure tones with frequencies between 353 and 8000 Hz, presented monaurally. A Principal Component Analysis (PCA) of the response in the auditory cortex revealed no difference in tonotopic organization, which confirmed earlier studies. A GLM analysis showed hyperactivity in the lateral areas of the bilateral auditory cortex. Consistent with the tonotopic map, this hyperactivity mainly occurred in response to low stimulus frequencies. This may be related to hyperacusis, which was associated with tinnitus found in the parahippocampus. This may reflect an interference between tinnitus and spatial orientation.

This paper proposed a three-layer distributed simulation network architecture: 1. Distributed virtual simulation network, 2. Perception and control sub-network, and 3. Collaborative communication service network. This simulation architecture runs on a distributed platform. The platform can provide a unique virtual scenario and several simulation services to verify the individual robot system's basic perception, control, and planning algorithms and the distributed collaborative algorithms of heterogeneous multi-robot systems. Furthermore, we designed a simulation experiment scenario for classical heterogeneous robot systems such as unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs). At last, We gave a rough estimation model of the bandwidth.

Although, promotion of urbanization culture in recent decades has made inevitable development of cities in the world, however, the development can be guided in a direction that leave, to the extent possible, minimum socioeconomic and environmental impacts. For this, it is required to first forecast auto-spreading orientation of cities and suburbs in rural areas over time and then avoid shapeless growth of cities. This paper is an attempt to develop a dynamic hybrid model based on logistic regression (LR), Markov chain (MC), and cellular automata (CA) for prediction of future urban sprawl in fast-growing cities. The model was developed using 12 widely-used urban development criteria, whose significant coefficient was determined by logistic regression, and validated by relative operating characteristic (ROC) analysis. The validated model was run in Guilan, a tourist province in northern Iran with a very high rate of urban development. For this, changes in the area of urban land use were detected over the period of 1989 to 2013 and then, future sprawl of the province was forecasted by the years 2025 and 2037. The analysis results revealed that the area of urban land use was increased by more than 1.7 % from 36012.5 ha in 1989 to 59754.8 ha in 2013, and the area of Caspian Hyrcanian forestland was reduced by 31628 ha. The results also predicted an alarming increase in the rate of urban development in the province by the years 2025 and 2037, during which urban land use is predicted to develop 0.9 % and 1.38 %, respectively. The development pattern is expected to be uneven and scattered, without following any particular direction. The development will occur close to the existing or newly-formed urban basements as well as around major roads and commercial areas. This development, if not controlled, will lead to the loss of 13863 ha of Hyrcanian forests and if the trend continues, 21013 ha of Hyrcanian forests and 20208 ha of Barren/open lands are expected to be destroyed by the year 2037. In general, the proposed model is an efficient tool for the support of urban planning decisions and facilitates the process of sustainable development of cities by providing decision-makers with an overview on future development of cities where the growth rate is very fast.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

In this work, two plasmonic structures with two different periodic nanostructures (nanodisk and nanostrip arrays) separated from the gold layer by an ultrathin dielectric Al2O3 layer are proposed, and their optical properties are simulated as 3-dimensional models using COMSOL Multiphysics software tool. The optical responses, such as the amplification of the electric field and the scattering, absorption and extinction cross sections of the two structures, are investigated and compared. The results show that both structures show strong field enhancement in their gap layer, and the structure with the periodic array of metal nanodisks shows stronger field enhancement and larger absorption, extinction, and scattering cross sections in its dipole resonance wavelength, which is defined as a bright plasmonic mode. In addition, some weaker resonant modes are observed for both structures and the reason for their generation is dis-cussed. The analysis of different possible modes in such structures is crucial for their application in various fields.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

In this paper, the boiling flow inside a nanochannel with 700000 argon particle has been simulated by molecular dynamics (MD) simulation. This approach has been employed to analysis the superheated flow and its heat transfer pattern as well. For all simulations an external thrust force varying from 1 PN to 12 PN is exerted on inlet nanoparticles along the channel to have the forced annular boiling flow. Computations reveal that saturation condition and superheat degree have significant impacts on the liquid-vapor interface. Furthermore, because of the major influence of surface tension throughout a nanochannel, the x-velocity of liquid film and vapor core has not considerable fluctuations and stay smooth. All provided results show the behaviors completely similar to the available outcomes in the literature.

Surgical simulators are crucial in early craniofacial and plastic surgical training, necessitating synthetic materials that accurately replicate tissue properties. Recent critiques of our lab’s currently deployed silicone surrogate have highlighted numerous areas for improvement. To further refine our models, our group's objective is to find a composition of materials that is closest in fidelity to native oral mucosa during surgical rehearsal by expert craniofacial surgeons. Fifteen platinum silicone-based surrogate samples were constructed with variable hardness and slacker percentages. These samples underwent evaluation of tactile sensation, hardness, needle puncture, cut resistance, suture retention, defect repair, and tensile elasticity. Expert craniofacial surgeon evaluators provided focused qualitative feedback on selected top-performing samples for further assessment and statistical comparisons. Evaluation revealed surrogate characteristics with satisfactory to good performance. Sample 977 exhibited the highest performance, and comparison with the original surrogate (sample 810) demonstrated significant improvements in critical areas, emphasizing the efficacy of the refined composition. The study identified a silicone composition that directly addresses the feedback received by our team’s original silicone surrogate. The study underscores the delicate balance between biofidelity and practicality in surgical simulation. The need for ongoing refinement in surrogate materials is evident to optimize training experiences for early surgical learners.

3D bioprinting holds great promise in the field of regenerative medicine as it can create complex structures in a layer-by-layer manner using cell-laden bioinks, making it possible to imitate native tissues. Current bioinks lack both the high printability and the biocompatibility required in this respect. Hence, the development of bioinks that are capable of both properties is needed. In our previous study, a furfuryl-gelatin based bioink, crosslinkable by visible light, was used for creating mouse mesenchymal stem cell-laden structures with high fidelity. In this study, lattice mesh geometries were printed in a comparative study to test against the properties of a traditional rectangular-sheet. After 3D printing and crosslinking, both structures were analysed for swelling and rheological properties, and their porosity estimated using scanning electron microscopy. Results showed that the lattice structure was relatively more porous but sturdy and exhibited a lower degradation rate compared to the rectangular-sheet. Further, the lattice allowed encapsulation of a greater number of cells, allowing them to proliferate to a greater extent compared to the rectangular-sheet that retained a lesser number of cells initially. All of these results collectively affirmed that the lattice poses as a superior scaffold design for tissue engineering applications.

Non-uniform grain boundary sliding can induce strain and rotation incompatibilities at perfectly planar interfaces. Explicit analytic expressions of stress and lattice rotation jumps are thus derived at a planar interface in the general framework of heterogeneous anisotropic thermo-elasticity with plasticity and grain boundary sliding. Both elastic fields are directly dependent on in-plane gradients of grain boundary sliding. It is also shown that grain boundary sliding is a mechanism that may relax incompatibility stresses of elastic, plastic and thermal origin although the latter are not resolved on the grain boundary plane. This relaxation may be a driving force for grain boundary sliding in addition to the traditionally considered local shears on the grain boundary plane. Moreover, the obtained analytic expressions are checked by different kinds of bicrystal shearing finite element simulations allowing grain boundary sliding and where a pinned line in the interface plane aims at representing the effect of a triple junction. A very good agreement is found between the analytic solutions and the finite element results. The performed simulations particularly emphasize the role of grain boundary sliding as a possible strong stress generator around the grain boundary close to the triple line because of the presence of pronounced gradients of sliding.

To address the requirements of sonar imaging, such as high receiving sensitivity, wide bandwidth, wide receiving angle, an AlN PMUT with an optimized ratio of 0.6 for the piezoelectric layer diameter to backside cavity diameter is proposed in this paper. A sample AlN PMUT is designed and fabricated with SOI substrate-based bulk MEMS process. The characterization test result of the sample demonstrates a -6 dB bandwidth of approximately 500 kHz and a measured receiving sensitivity per unit area of at 1.37 V/μPa/mm2, which significantly surpasses the performance of previously reported PMUTs. The -6 dB horizontal angles of the AlN PMUT at 300 kHz and 500 kHz are measured 68.30° and 54.24°, respectively. To achieve an accurate prediction of its characteristics when being packaged and assembled in a receive array, numerical simulations with the consideration of film stress are conducted. The numerical result shows a maximum deviation of ±7% in the underwater receiving sensitivity across the frequency range of 200 kHz to 1000 kHz and a deviation of about 0.33% in the peak of underwater receiving sensitivity comparing to the experimental data. By such good agreement, the simulation method reveals its capability of providing theoretical foundation for enhancing the uniformity of the AlN PMUTs in future studies.

Polarons, quasiparticles resulting from the interaction between an impurity and the collective excitations of a medium, play a fundamental role in physics, mainly because they represent an essential building block for understanding more complex many-body phenomena. In this manuscript, we study the spectral properties of a single impurity mixed with identical bosons in a one-dimensional lattice with power-law hopping. In particular, based on the so-called T-matrix approximation, we show the existence of well-defined quasiparticle branches for several tunneling ranges and for both, repulsive and attractive impurity-boson interactions. Furthermore, we demonstrate the persistence of the attractive polaron branch when the impurity-boson bound state is absorbed into the two-body continuum and that the attractive polaron becomes more robust as the range of the hopping increases. The results discussed here are of relevance for the understanding of the equilibrium properties of quantum systems with power-law interactions.

The presented research article shows a functionally graded lattice as an infill structure in designing a 3D printed mechanical element—a bicycle crank arm. The authors want to answer the fundamental question: whether the functionally graded lattice structures can efficiently improve structural performance and how they can be implemented in real complex components. Intuitively, everyone senses that using such elements must bring profit. A good example might be nature, which commonly reaches for such a solution in the skeletons of animals and humans. Two aspects determine their realisations: the lack of adequate construction and analysis methods and the limitations of existing manufacturing methods. Thus, the authors used relatively simple crank arm design and design exploration methods for structural analysis. The design exploration method enabled us to find the optimum solution efficiently. A developed prototype was created utilising additive manufacturing. One of the 3D printing methods - fused filament fabrication technology for metals, allowed the prototype of a crank arm with the optimised infill to be made. As a result, the authors developed a lightweight and manufacturable crank arm showing the new construction and analysis method implementable in similar 3D printed elements.

Laser powder bed fusion (L-PBF) is a type of additive manufacturing technology that processes metal powders into a component. Support structures are an essential part of the L- PBF process as they transfer the laser-induced heat during and shortly after the process to the substrate, sustaining positional accuracy of downward facing surfaces of the component. Since the use of support structures is inevitable, optimized designs for them are crucial in realizing more sustainable production process. In a serial production setup, reducing the lead time and cost of a non-value-added process step like support structure removal is of significance when improving the overall business case and competitiveness.The goal of this study was to verify the applicability of lattice-based support structures for L-PBF. To achieve this, different lattice types as support structures were designed. They were tested, compared and verified for a Siemens gas turbine component. The results showed that the generated lattice-based support structures could be suitable for L-PBF. The supports had to be designed appropriately such that they could preserve the geometry of the part. Furthermore, they had to have a short fabrication time and to be removable easily, preferably without machining or sawing.

We present a unified approach to the thermodynamics of hadron-quark-gluon matter at finite temperatures on the basis of a quark cluster expansion in the form of a generalized Beth-Uhlenbeck approach with a generic ansatz for the hadronic phase shifts that fulfills the Levinson theorem. The change in the composition of the system from a hadron resonance gas to a quark-gluon plasma takes place in the narrow temperature interval of 150−185 MeV where the Mott dissociation of hadrons is triggered by the dropping quark mass as a result of the restoration of chiral symmetry. The deconfinement of quark and gluon degrees of freedom is regulated by the Polyakov loop variable that signals the breaking of the Z(3) center symmetry of the color SU(3) group of QCD. We suggest a Polyakov-loop quark-gluon plasma model with O(αs) virial correction and solve the stationarity condition of the thermodynamic potential (gap equation) for the Polyakov loop. The resulting pressure is in excellent agreement with lattice QCD simulations up to high temperatures.

Efficient member revocation and strong security against attacks are prominent requirements in group signature schemes. Among the revocation approaches Verifier-local revocation is the most flexible and efficient method since it requires to inform only the verifiers regarding the revoked members. The verifier-local revocation technique uses a token system to manage members’ status. However, the existing group signature schemes with verifier-local revocability rely on weaker security. On the other hand, existing static group signature schemes rely on a stronger security notion called, full-anonymity. Achieving the full-anonymity for group signature schemes with verifier-local revocation is a quite challenging task. This paper aims to obtain stronger security for the lattice-based group signature schemes with verifier-local revocability, which is closer to the full-anonymity. Moreover, this paper delivers a new key-generation method which outputs revocation tokens without deriving from the users’ signing keys. By applying the tracing algorithm given in group signature schemes for static groups, this paper also outputs an efficient tracing mechanism. Thus, we deliver a new group signature scheme with verifier-local revocation that satisfies a stronger security from lattices.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

A triangular lattice model for pattern formation by core-shell particles at fluid interfaces is introduced and studied for the particle to core diameter ratio equal to 3. Repulsion for overlapping shells and attraction at larger distances due to capillary forces are assumed. Ground states and thermodynamic properties are determined analytically and by Monte Carlo simulations for soft outer- and stiffer inner shells, with different decay rates of the interparticle repulsion. We find that thermodynamic properties are qualitatively the same for slow and for fast decay of the repulsive potential, but the ordered phases are stable for temperature range depending strongly on the shape of the repulsive potential. More importantly, there are two types of patterns formed for fixed chemical potential - one for a slow and another one for a fast decay of the repulsion at small distances. In the first case two different patterns - for example clusters or stripes - occur with the same probability for some range of the chemical potential. For fixed concentration, an interface is formed between two ordered phases with the closest concentration, and the surface tension takes the same value for all stable interfaces. In the case of degeneracy, a stable interface cannot be formed for one out of four combinations of the coexisting phases, because of a larger surface tension. Our results show that by tuning the architecture of a thick polymeric shell, many different patterns can be obtained for sufficiently low temperature.

This paper presents a comparative study of heat transfer performance of lattice structured heat sinks. 20 different unit cells were chosen and heat sinks were modelled in nTop with constant unit cell size. Al 6061 alloy was chosen for analysis due to its good thermal conductivity, low weight, low cost, and high strength. Steady state thermal analysis was performed using ANSYS with constant input parameters for all samples. Heat flux and temperature distribution within the heat sinks were analysed. The study aims to provide a comprehensive understanding of the thermal performance of lattice heat sink designs.

The lattice reduction aided(LRA) algorithm has attracted widely attention of researchers in MIMO systems because of its low complexity to achieve full diversity. However, most lattice reduction auxiliary algorithms do not directly improve system performance. In this paper, a modified lattice reduction successive interference cancellation (SIC) algorithm is proposed for MIMO OFDM system mild changing the complexity of LRA algorithm. At present, the MMSE SQRD algorithm has the problem of regarding too much useful signals as the residual interference which cannot be cancelled by successive interference cancellation. Since the diagonal elements of useful signals are non-zero, the components of the symbols to be detected still present in the interference term, treating all the signals as interference will be resulted in performance loss. To solve this problem, the modified matrix is proposed.by moving this symbol component into the signal term, the proposed algorithm can provide the better performance than MMSE SQRD algorithm. The analysis shows that the LRA-MMSE-SIC algorithm of proposed in this paper significantly improves the system performance with mild increasing the complexity. The simulation results show that the performance of the proposed algorithm is improved by 1dB and 8dB compared with the comparison algorithm when the bit error rate is 10−3.

Anyon is collective excitation of two dimensional electron gas subjected to strong magnetic field, carrying fractional charges and exotic statistical character beyond fermion and boson. So far, anyons with serial fractional charges only exist in fractional quantum Hall effect. It is still a challenge to find new serial of fractional charges in other physical system and develop an unified mathematical physics theory based on the same root. Here a topological path fusion theory of propagating electrons in magnetic flux lattice is proposed to explore the physical origin of fractional charges based on a generalization of Feynman's path integral theory and Thurston's train track theory. This mathematical physics theory generated the existed serial of fractional charges in fractional quantum Hall effect and predicted new serial of fractional charges. A serial of irrational charges are predicted in one dimensional lattice of magnetic fluxes. Fractionally charged anyons are also generated in two dimensional and three dimensional lattice of train tracks of electric currents, revealing an exact correspondence between knot lattice model and train track model. A new explanation for the modular symmetry of complex Hall conductance and composite fermion in fractional quantum Hall effect is also derived from this topological path fusion theory. Experimental observation of anyon in three dimensions can be realized by constructing three dimensional interlocking magnetic fluxes or mapping magnetic fluxes into forbidden zones in multi-connected space filled by solid state material. A photonic crystal with porous nano-structures is a promising system for detecting fractional charges and paves a new way for topological quantum computation.

The Landau damping effect was observed in collisionless plasma, as a microscopic resonant mechanism between electromagnetic radiation and the collective modes. In this paper we demonstrate the occurrence of the Landau damping at macroscopic scale in the interaction between water waves and anharmonic lattice of magnetic buoys. By coupling the Navier-Stokes equations for incompressible fluid with the nonlinear dynamics of an anharmonic magnetic lattice we obtain a resonant transfer of momentum and energy between the two systems. The velocity of the flow is obtained in the Stokes approximation with Basset type of drag force. The dynamics of the buoys is calculated in the surfactant approximation for a specific frequency, then we use Fourier analysis to obtain the general time variable interaction. After involving an integral Dirichlet transform we obtain the time dependent expression of the drag force, the interaction waves-lattice with a new term in the form of a Caputo fractional derivative. We compare the results of the model with experiments performed in a wave tank with free floating magnetic buoys under the action of small amplitude gravitational waves. This configuration can be applied in studies for the attenuation with resonant damping of rogue waves, storms or tsunamis.

Agricultural greenhouse is largely answered in the agricultural sphere, despite the shortcomings it has, including overheating during the day and night cooling which sometimes results in the thermal inversion mainly due to its low inertia. The glasshouse dressed chapel is relatively more efficient than the conventional tunnel greenhouse. Its proliferation on the ground is more or less timid because of its relatively high cost[14-22]. Agricultural greenhouse aims to create a favorable microclimate to the requirements of growth and development of culture, from the surrounding weather conditions, produce according to the cropping calendars fruits, vegetables and flower species out of season and widely available along the year. It is defined by its structural and functional architecture, the quality thermal, mechanical and optical of its wall, with its sealing level and the technical and technological accompanying[12-13]. The greenhouse is a very confined environment, where multiple components are exchanged between key stakeholders and them factors are light, temperature and relative humidity[8]. This state of thermal evolution is the level sealing of the cover of its physical characteristics to be transparent to solar, absorbent and reflective of infrared radiation emitted by the enclosure where the solar radiation trapping effect otherwise called "greenhouse effect" and its technical and technological means of air that accompany. The socio-economic analysis of populations in the world leaves appear especially the last two decades of rapid and profound transformations These changes are accompanied by changes in eating habits, mainly characterized by rising consumption spread along the year[14]. To effectively meet this demand, greenhouse-systems have evolved, particularly towards greater control of production conditions (climate, irrigation, ventilation techniques, CO2 supply, etc ...). Technological progress has allowed the development of greenhouses so that they become increasingly sophisticated and of an industrial nature (heating, air conditioning, control, computer, regulation, etc ...). New climate driving techniques have emerged, including the use of control devices from the classic to the use of artificial intelligence[10-11] such as neural networks and / or fuzzy logic, etc... As a result, the greenhouse growers prefer these new technologies while optimizing the investment in the field to effectively meet the supply and demand of these fresh products cheaply and widely available throughout the year.

The osseointegration process in and around additively manufactured (AM) lattice structures of a new titanium alloy, Ti–19Nb–14Zr, was evaluated. Three different implants, including lattices with increasing high sidewalls gradually closing them, were designed, manufactured and implanted in the tibia and metatarsal bone of two sheep for twelve weeks. After removal, they were characterized with X-ray computed tomography (XCT). The 3D XCT images were segmented using machine learning. The bone-interface implant (BII) and bone-implant contact (BIC) were studied. The results show that, since AM naturally leads to high roughness surface finish, the wettability of the implant is increased. The new alloy possesses an increased affinity to the bone enhancing the quality of osseointegration. The lattice provides crevices, in which the biological tissue can jump in and cling. The combination of these factors is pushing ossification beyond its natural limits. Therefore, the quality and speed of the ossification and osseointegration in and around these Ti–19Nb–14Zr AM laterally closed lattice implants open the possibility of bone spline key of prostheses. This enables the stabilization of the implant into the bone while keeping the possibility of punctual hooks allowing the implant to be removed more easily if required.

The object of study in the article is the auxiliary variable-frequency electric drive onboard of an AC electric locomotive, and more precisely, the structure and parameters of the control system of the active corrector of power factor (ACPF), which is part of the electric drive, as a unit that ensures electromagnetic compatibility of the electric drive with other equipment on board the electric locomotive and catenary and its energy efficiency. The topic of the article's research is the substantiation of the structure of the ACPF control system, the choice of types (transfer functions) of controllers and the calculation of their parameters. The research method chosen was the calculation of the transfer functions of the controllers of the cascaded loops control system, followed by computer simulation using the OrCAD software. The results of simulating a cascaded two loops control system of an ACPF with different types of controllers are presented and analytically compared. It is concluded that it is advisable to use a cascaded two loops control system, containing a voltage control loop and a current control loop. The best results show the simulation when using an aperiodic current controller (A-controller) and a proportional-integral voltage controller (PI-controller). The data obtained serve as the basis for further improvement of the operation of the ACPF by enhancing and optimizing the settings, structure and algorithms of the control system, which, with the selected hardware of power converter unit, will allow the ACPF to perform its functions with a high degree of reliability in an entire range of disturbing and control influences.

Perovskite solar cells (PSCs) are vital for their optical and electrical properties, with lead-based PSCs reaching a remarkable efficiency of 26.1%, while tin-based counterparts achieve 18.71%. Due to lead's toxicity, there's a push for alternatives like tin. However, tin-based PSCs suffer from stability issues and high defect density states, necessitating the development of cost-effective, high-performance, and eco-friendly alternatives. In this study, we designed a hetero-junction architecture using MASnI3-based Perovskite, opti-mized with SCAPs-1D. After exhaustive analysis, our device achieved a power conversion efficiency of 24.18%, with enhanced parameters including Voc of 0.09323V, Jsc of 30.8360 mA/cm2, and FF of 84.10%. Recombination rates, particularly Shockley-Read Hall recom-bination, were significantly reduced. Parametric analyses, encompassing absorber layer thickness, band gap, defect density, doping concentration, and operating temperature, in-dicate potential efficiency enhancements. This underscores the viability of Sn-based PSCs as a cost-effective, efficient, and environmentally benevolent alternative to lead-based counterparts, promising advancements in future research and development efforts.

The security of several fully homomorphic encryption (FHE) schemes depends on the intractability assumption of the approximate common divisor (ACD) problem over integers. Subsequent efforts on solving the ACD problem as well as its variants were also developed during the past decade. In this paper, an improved orthogonal lattice (OL) based algorithm, AIOL, is proposed to solve the general approximate common divisor (GACD) problem. The conditions for ensuring the feasibility of AIOL are also presented. Compared to the Ding-Tao’s OL algorithm, the well-know LLL reduction is used only once in AIOL, and when the error vector r is recovered in AIOL, the possible difference between the restored and the true value of p is given. The experimental comparisons towards the Ding-Tao’s algorithm and ours are also provided for validating our improvements.

A better understanding of high temperature processes in slags contributes to facilitate knowledge based design of the solidified product. Here, a slag analogue with a nominal composition of 17 wt% LiMnO2 and 83 wt% Ca2SiO4 was synthesized encountering fairly high cooling rates. The Mn species from 1223 K to 1773 K was simulated using a thermodynamic model assuming a homogeneous melt. The micro-composition including the Mn species of the solidified slag was determined experimentally and was used as basis for molecular dynamics (MD) simulation. The MD simulation provides information on structure and viscosity at high temperatures, otherwise difficult to access. These parameters significantly influence oxidation state of redox-active elements and the solidified product. The micro-composition analyzed by electron probe micro analysis (EPMA) and synchrotron based micro-X-ray fluorescence (micro-XRF) showed that Mn-rich and Ca-Si-rich phases are separated. While the Mn-O phases did not contain noticeable Ca, the Ca2SiO4 phase had incorporated 0.6 wt% of Mn. The slag solidified into round shaped and droplet shaped grains of a Li-Mn-oxide, some Mn3O4 and Ca2SiO4. The powder X-ray diffraction (PXRD) confirmed the formation of larnite, the identity of the Li-Mn-oxide however remained inconclusive. The Mn oxidation state (OS) was identified using synchrotron based micro-X-ray absorption near edge spectroscopy (micro-XANES). The Mn-O grains, matched well with Li-Mn-oxides and a Mn OS: +3 e.g. LiMn3+O2. Small areas matching Hausmannite (Mn2+Mn23+O4) were also identified. The OS of Mn in the silicate phase could not be identified. For comparison a slowly cooled slag analogue with similar composition however higher Si content, was also subjected to micro-XANES. The slowly cooled slag formed long Mn-rich needles in a matrix of large calcium silicate crystals. The Mn-rich crystals matched well with the XANES spectrum of a Mn3+ Li-oxide like LiMn3+O2. At the rim of the needles the Mn-spectra matched well the Hausmannite (Mn2+Mn23+O4) reference. In the silicate phases Mn had a OS: +2, unambiguously. The melt structure at different temperatures of two compositions i.e. LiMn3+O2 and Ca2SiO4 was simulated using molecular dynamics (MD). They serve as model compositions assuming a heterogeneous melt. The results show significant different degrees of polymerization and viscosity. Information from MD simulations can support the identification of potentially different oxygen permeability and with that prediction of oxidation states. The bulk composition was identified by inductively coupled plasma optical emission spectrometry (ICP-OES), bulk structure by PXRD and bulk species by lab-XANES. The synchrotron micro analysis including micro-XRD were performed at the microfocus beamline I18 at the Diamond Light Source. Pure reference compounds were prepared and characterized with the same multi-modal approach.

We propose a method that enables precise determination of the number of atoms in a Dick-noise-free optical lattice clock, by effectively addressing quantum projection noise. Our approach relies on conducting stability measurements at three distinct parameter sets, allowing us to differentiate between quantum projection noise, photon shot noise, and technical noise. Importantly, our method enables accurate extraction of the atom number, even in the presence of photon shot noise and technical noise. To validate the effectiveness of our approach, we employ numerical simulations and optimize the modulation parameters to achieve the smallest uncertainty possible. The numerical simulations show the validity of our method and demonstrate a measurement uncertainty in the atom number that is below 4% across a wide range of atom numbers, provided that the standard deviation of atom number fluctuation is kept below 0.23 times the average atom number.

Additive manufacturing enables the realization of complex component designs that can not be achieved with conventional processes, such as the integration of lattice structures for weight reduction. To include lattice structures in component designs, an automated algorithm compatible to conventional CAD is required that is able to handle various lattice topologies as well as variable local shape parameters such as strut radii. Furthermore, smooth node transitions are desired since previous studies indicate advantages regarding reduced stress concentrations and the structural response to loadings such as fatigue performance. The surface patch-based algorithm developed in this work is able to solidify given lattice frames to smooth lattice structures without manual construction steps. The algorithm requires only a few seconds of sketching time for each node and favours paralellization. Automated special case workarounds as well as fallback mechanisms are considered for non-standard inputs. It is demonstrated on irregular lattice topologies and applied for the construction of a lattice infill of an aircraft component that was additively manufactured.

The center vortex model of quantum-chromodynamics can explain confinement and chiral symmetry breaking. We present a possible resolution for problems of the vortex detection in smooth configurations and discuss improvements for the detection of center vortices.

The quasi-two-dimensional organic charge-transfer salt κ-(BEDT-TTF)₂Cu₂(CN)₃ is one of the prime candidates for a quantum spin-liquid due the strong spin frustration of its anisotropic triangular lattice in combination with its proximity to the Mott transition. Despite intensive investigations of the material's low-temperature properties, several important questions remain to be answered. Particularly puzzling are the 6 K anomaly and the enigmatic effects observed in magnetic fields. Here we report on low-temperature measurements of lattice effects which were shown to be particularly strongly pronounced in this material (R. S. Manna et al., Phys. Rev. Lett. 104, 016403 (2010)). A special focus of our study lies on sample-to-sample variations of these effects and their implications on the interpretation of experimental data. By investigating overall nine single crystals from two different batches, we can state that there are considerable differences in the size of the second-order phase transition anomaly around 6 K, varying within a factor of 3. In addition, we find field-induced anomalies giving rise to pronounced features in the sample length for two out of these nine crystals for temperatures T < 9 K. We tentatively assign the latter effects to B-induced magnetic clusters suspected to nucleate around crystal imperfections. These B-induced effects are absent for the crystals where the 6 K anomaly is most strongly pronounced. The large lattice effects observed at 6 K are consistent with proposed pairing instabilities of fermionic excitations breaking the lattice symmetry. The strong sample-to-sample variation in the size of the phase transition anomaly suggests that the conversion of the fermions to bosons at the instability is only partial and to some extent influenced by not yet identified sample-specific parameters.

Nowadays, unmanned vehicles are widely used in various fields. However, the safety of unmanned vehicles is directly determined by the autopilot systems, and sensor faults are a very critical factor that affects the normal operation of the autopilot systems. To efficiently and comprehensively test unmanned systems for sensor faults, this paper proposes a chip-level testing platform for unmanned vehicle autopilot systems based on FPGA hardware-in-the-loop simulation. Unlike existing testing platforms, the introduction of FPGA technology allows us to achieve nanosecond real-time simulation frequency, thus realizing chip-level simulation of sensors and black-box automated testing. Firstly, we propose a set of general platform and modeling methods, and the paper presents a detailed application of the four most common necessary sensors in autopilot systems as examples. Secondly, we propose for the first time a chip-level fault testing method for unmanned systems, and build a test platform with a quadrotor vehicle, the PX4 software platform, and the Pixhawk4 hardware platform as examples. Finally, the experimental results verify that the testing platform proposed in this paper can adapt to various autopilot systems and has high simulation test reliability.

The medium-voltage DC (MVDC) technology has gained increasing interests in recent years. Power electronics devices dominate those grids. Accurate simulation of such a grid, with detailed models of switching semiconductors, can quickly became very time-consuming, according to the number of connected devices to be simulated. A simulation approach based on interactions on a continuous time model can be very interesting, especially for developing a system level control model of such a modern MVDC distribution grid. Aim of this paper is to present all the steps required for obtaining a continuous time modelling of a +/- 10 kV MVDC grid case study, including Solid State Transformer (SST) and Modular Multilevel Converter (MMC) based Active Front End (AFE). Additional aim of this paper is to supply an educational content about the use of the continuous time simulation approach, thanks to a detailed description of the various devices modelled into the presented MVDC grid. The results of a certain number of simulation scenarios are eventually presented.

: Suicide is a serious public health problem, with a global mortality rate of 1.4% of all deaths worldwide, and the leading cause of unnatural death in Spain. The use of clinical simulation has proven to be a beneficial tool in the training of nursing students. Such experiences allow them to develop cognitive and affective skills that are fundamental for the detection of warning signs and use of interventions in cases of people who want to take their own lives. Working in a mental health environment can be difficult for nursing students; therefore, the purpose of this study was to explore the perceptions of nursing students on the approach, management and intervention of suicidal crisis through clinical mental health simulation. Methods: qualitative descriptive phenomenological study through focus groups and reflective narratives in a sample of 45 students. A thematic analysis was performed using ATLAS-ti. Results: After the analysis, three themes were obtained: (a) management and handling of emotions (b) identification of suicide motives (c) intervention in suicidal crisis. Discussion: Clinical simulation in mental health allows students to exercise clinical judgment reasoning, detect warning signs for a better treatment approach, and provide tools for effective intervention and management of patient care. The results of this study indicate that nursing students face challenges in approaching mental health clinical simulation due to lack of prior exposure.

This study aimed to solve the problems of sealing and tearing failure of packer’s rubber cylinders during CO2 downhole injection. Using the simulation software, Comsol, a rubber cylinder model in a supercritical CO2 (SC-CO2) environment was established. The thermal analogy method was used to simulate the CO2 diffusion and rubber cylinder swelling process, thus we analyzed the deformation and stress of the rubber cylinder caused by temperature, pressure and CO2 as swelling agent. Results showed that, in the SC-CO2 environment, under the influence of CO2 diffusion and the consequent swelling, the rubber cylinder body is prone to large deformation, and the maximum shear stress is significantly increased, leading to shear failure of the rubber cylinder. The reduction of the initial seating pressure can alleviate the impact of deformation, whereas the reduction of the maximum contact pressure could cause the rubber cylinder to lose its seal. We also analyzed the change rules between various factors and the maximum contact pressure of the rubber cylinder, which provides a theoretical basis and technical support for improving the sealing performance of the packer’s rubber cylinder in the SC-CO2 environment.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

This paper introduces a new adaptation of the enthalpic lattice Boltzmann method (LBM) tailored to simulate the intricate dynamics of conjugate heat transfer in non-homogeneous media, showcasing considerable potential for enhancing heat exchanger designs. This approach expands upon the conventional enthalpic LBM framework by seamlessly incorporating tailored source terms, enabling precise representation of local and transient variations in the medium’s thermophysical properties. The resulting LBM model comprehensively captures the energy conservation equation, with exceptions made only for flow compressibility and viscous dissipation, thereby significantly augmenting its versatility in analyzing heat exchanger configurations. Verification tests, comprising assessments of both transient and steady-state solutions, unequivocally validate the accuracy of the proposed model, further bolstering its reliability for analyzing heat exchange processes within intricate heat exchanger geometries. To demonstrate its efficacy, simulations of conjugate heat transfer processes involving fluid natural convection within structured cavities were performed, imposing both Dirichlet and Neumann boundary conditions to emulate scenarios encountered in practical heat exchanger operations. The findings yield compelling insights, particularly in the transient regime, revealing the beneficial impact of structured cavities on enhancing heat transfer processes. These insights inform potential design optimizations for heat exchangers. The results emphasize the potential of the modified enthalpic LBM approach to elucidate complex heat transfer phenomena in non-homogeneous media and structured geometries, offering valuable implications for heat exchanger engineering and optimization.

The manuscript presents a novel approach to designing and fabricating a stretchable patch antenna designed for strain sensing and wireless communication of sensing data at the same time. The challenge lies in combining flexible and stretchable textile materials with different physical mor-phologies, which can hinder adhesion among multiple layers when stacked up, resisting the overall stretchability of the antenna. The proposed antenna design overcomes this challenge by incorpo-rating a lattice hinge pattern in the non-stretchable conductive e-textile, transforming it into a stretchable structure. The innovative design includes the longitudinal cuts inserted in both the patch and the ground plane of the antenna, allowing it to stretch along in the perpendicular direction. Implementing the lattice hinge pattern over the conductive layers of the proposed patch antenna in combination with a 2 mm thick Polydimethylsiloxane (PDMS) substrate achieves a maximum of 25% stretchability compared to its counterpart antenna without lattice hinge design. The stretchable textile antenna resonates around a frequency of 2.45 GHz and exhibits a linear resonant frequency shift when strained up to 25%. This characteristic makes it suitable for use as a strain sensor. Ad-ditionally, the lattice hinge design enhances the conformability and flexibility of the antenna compared to a solid patch antenna. The realized antenna gains in the E and H-plane were measured as 2.21 dBi and 2.34 dBi, respectively. Overall, the presented design offers a simple and effective solution for fabricating a stretchable textile patch antenna for normal use or as a sensing element, opening up possibilities for applications in communication and sensing fields.

The Physics-Informed Neural Networks (PINNs) improve the efficiency of data utilization by combining physical principles with neural network algorithms and ensure that the predictions are consistent and stable with the physical laws. PINNs opens up a new approach to address inverse problems in fluid mechanics. Based on the single-relaxation-time lattice Boltzmann method (SRT-LBM) with the Bhatnagar-Gross-Krook (BGK) collision operator, the PINN-SRT-LBM model is proposed in this paper for solving the inverse problem in fluid mechanics. The PINN-SRT-LBM model consists of three components. The first component involves a deep neural network that predicts the equilibrium control equations in different discrete velocity directions within SRT-LBM. The second component employs another deep neural network to predict non-equilibrium control equations, enabling inference of the fluid's non-equilibrium characteristics. The third component, a physics informed function translates the outputs of the first two networks into physical infor-mation. By minimizing the residuals of the physical partial differential equations (PDEs), the physics informed function infers relevant macroscopic quantities of the flow. The model evolves two sub-models applicable to different dimensions, named PINN-SRT-LBM-I and PINN-SRT-LBM-II models according to the construction of the physical informed function. The innovation of this work is the introduction of SRT-LBM and discrete velocity models as physical drivers into the neural network through the interpretation function. Therefore, PINN-SRT-LBM allows the neural network to handle inverse problems of various dimensions and focus on problem-specific solving. Experimental results confirm the accurate prediction of flow infor-mation at different Reynolds numbers within the computational domain. Relying on the PINN-SRT-LBM models, inverse problems in fluid mechanics can be solved efficiently.

Dielectric barrier discharge (DBD) plasma has several applications in different fields. One of these fundamental applications is medical usages, where various methods are employed to improve the plasma treatment process. The combination of different gases is one of the important strategies to improve the performance of plasma in treatment. In this paper, the optimized plasma parameters for one-dimensional radiofrequency discharge produced at low pressures in a helium gas combination is studied. In this research, the optimal combination of H₂O and He is identified to attain the highest amount of reactive oxygen species (ROS). Considered mixture are 5,10,15 and 20 precent of H₂O for one dimensional helium gas discharge. The results show that the parameters of the output plasma are highly dependent on the composition of the input gases. It is found that the greatest concentrations of H+, He+, Hes (excited helium), and OH/ densities are observed when the H₂O percentage is 10%. Moreover, the density distributions of various species and the temperatures of electrons are numerically calculated during the electrical discharge process. These findings provide useful knowledge on how to optimize plasma parameters for biomedical applications, which may lead to improved treatment results in several therapeutic areas.

Falls are considered a significant cause of disability, pain, and premature deaths in older adults, often due to sedentary lifestyles and various risk factors. Combining immersive virtual reality (IVR) with physical exercise, or exergames, enhances motivation and personalizes training, effectively preventing falls by improving strength and balance in older people. IVR technology may increase the ecological validity of the assessments. The main goal of our study was to assess the feasibility of using a KAVE-based VR platform combining simulations of Levadas and a Cable Car to perform a balanced assessment and profiling of the older adult population for high risk-of-falls and the related user experience. A VR-based platform using a Wii balance board and a CAVE was developed to assess balance and physical fitness. Validated by the Biodex Balance System (BBS), 25 older adults participated in this study. The usability and presence were measured through the System Usability Scale and ITC-SOPI questionnaires, respectively. The IVR system showed a high presence and a good usability score of 75. Significant effects were found in the maximum excursion of the Centre of Pressure (COP) on the anterior-posterior axis during the Cable Car Simulation (CCS), correlating with BBS metrics. Multiple discriminative analysis models and the support vector machine classified fall risk with moderate to high accuracy, precision, and recall. The system accurately identified all high-risk participants using the Leave-One-Out method. This study suggests that an IVR-based platform based on simulations with high ecological validity can be used to assess physical fitness and identify individuals at a higher risk of falls.

We consider mixture experiments in which the proportions of the components must be non-negative and their sum must equal one. Thus, the experimental region for a mixture of components is a simplex. Li and Zhang (2017) made the conjecture that the pseudo component transformation of the lattice points in the simplex has a special property. In this paper, we show that this conjecture is not true in general. Furthermore, we refine this conjecture and prove the refined conjecture.

In these last years, self-healing polymers have emerged as a topic of considerable interest owing to their capability to partially restore material properties and thereby extend the product's lifespan. The main purpose of this study is to investigate the nano-indentation response in terms of hardness, reduced modulus, contact depth and coefficient of friction of a self-healing resin developed for use in aeronautical and aerospace contexts. To achieve this, the bifunctional epoxy precursor underwent tailored functionalization to improve its toughness, facilitating effective compatibilization with a rubber phase dispersed within the host epoxy resin. This approach aimed to highlight the significant impact of the quantity and distribution of rubber domains within the resin on enhancing its mechanical properties. The main results are that pure resin exhibits a higher hardness (about 36.7% more) and reduced modulus (about 7% more), consequently leading to a lower contact depth and coefficient of friction (11.4% less) compared to other formulations that, conversely, are well-suited for preserving damage from mechanical stresses due to their capabilities in absorbing mechanical energy. Furthermore, finite element method (FEM) simulations of the nanoindentation process were conducted. The numerical results were meticulously compared with experimental data, demonstrating a good agreement. This validation of the FEM model underscores its efficacy in predicting the mechanical behavior of nanocomposite materials under nanoindentation. The proposed investigation aims to contribute knowledge and optimization tips about self-healing resins.

Metal nanoparticles supporting plasmons are widely used to enhance electromagnetic fields, resulting in strong light-matter interactions at the nanoscale in a diverse range of applications. Recently, it has been shown that when metal nanorods are periodically arranged with proper lattice periods, surface lattice resonances (SLRs) can be excited and near fields can be greatly enhanced over extended volumes. In this work, we report significant near field enhancement over even larger volumes by placing the metal nanorod array within a Fabry-Pérot (F-P) microcavity. Results show that taking advantage of strong coupling between the SLR and the photonic F-P resonances, the electric field intensity of the bonding split mode can be enhanced by up to 1935 times, which is about three times of the enhancement of the SLR, and the greatly enhanced field can extend over most of the F-P microcavity. We further show that the F-P resonances of both odd and even orders can strongly couple to the SLR by varying the nanorods position from the middle of the microcavity. We expect that the proposed plasmonic-photonic coupling system will find promising applications in nanolasers, nonlinear optics and sensing.

Sources are classified into two depending upon the factor of reviving. These sources, which cannot be revived into their original shape once they are consumed, are considered as nonrenewable energy resources, i.e., (coal, fuel) Moreover, those energy resources which are revivable to the original condition even after being consumed are known as renewable energy resources, i.e., (wind, solar, hydel) Renewable energy is a cost-effective way to generate clean and green electrical energy Now a day’s majority of the countries are paying heed to energy generation from RES Pakistan is mostly relying on conventional energy resources which are mostly nonrenewable in nature coal, fuel is one of the major resources, and with the advent of time their prices are increasing on the other hand RES have great potential in the country with the deployment of RES greater reliability and an effective power system can be obtained In this thesis, a similar concept is being used and a hybrid power system is proposed which is composed of intermixing of renewable and nonrenewable sources The Source side is composed of solar, wind, fuel cells which will be used in an optimal manner to serve load The goal is to provide an economical, reliable, uninterruptable power supply. This is achieved by optimal controller (PI, PD, PID, FOPID) Optimization techniques are applied to the controllers to achieve the desired results. Advanced algorithms (Particle swarm optimization, Flower Pollination Algorithm) will be used to extract the desired output from the controller Detailed comparison in the form of tables and results will be provided, which will highlight the efficiency of the proposed system.

The aim of this work is to introduce a mathematical model representing the evolution of the temperature in a vegetation cover and the ground underneath it. Vegetation, and its interaction with soil, plays a very important role in the protection of soil surface from the action of sun and precipitations. A reduction in the vegetated mass increase the risk of desertification, soil erosion or surface runoffs which which can give rise to soil loss and sediment retention. These processes can favour climate change and global warming, which are major concerns nowadays. The mathematical model presented takes into account the main processes involved in vegetation cover and the interaction with the soil, among which, we can mention the Leaf Area Index, which is a dimensionless quantity defined as the one-sided green leaf area per unit ground surface area, or albedo and co-albedo which are clearly influenced by the vegetation. It is also considered a nonlinear heat capacity in the soil which incorporates the latent heat of fusion, when the phase change takes place. The numerical technique used to solve the mathematical model is based on a finite volume scheme with Weighted Essentially Non Oscillatory technique for spatial reconstruction and the third order Runge-Kutta Total Variation Diminishing numerical scheme is used for time integration. Some numerical examples are solved to obtain the distribution of temperature both in the vegetation cover and the soil.

In this study, the multi-relaxation-time lattice Boltzmann method is applied to investigate the oscillatory instability of lid-driven flows in two-dimensional semi-elliptical cavities with different vertical to horizontal aspect ratios K in the range of 1.0--3.0. The program implemented in this study is parallelized using CUDA (compute unified device architecture), a parallel computing platform, and computations are carried out on NVIDIA Tesla K40c GPU. To carry out precise calculations, the CUDA algorithm is extensively investigated, and its parallel efficiency indicates that the maximum speedup is 47.6 times faster. Furthermore, the steady--oscillatory Reynolds numbers are predicted by implementing the CUDA-based programs. The amplitude coefficient is defined to quantify the time-dependent oscillation of the velocity magnitude at the monitoring point. The simulation results indicate that the transition Reynolds numbers correlate negatively with the aspect ratio of the semi-elliptical cavity, and are smaller than those of the rectangular cavity at the same aspect ratio. In addition, the detailed vortex structures of the semi-elliptical cavity within a single period are also investigated when the Reynolds number is larger than the steady--oscillatory value to determine the effects of periodic oscillation of the velocity magnitude.

The rapid integration of Information and Communication Technology (ICT) is transforming the traditional electrical grid into a {\em Smart Grid}. Smart grids enable two-way communication and improved monitoring and control between utilities and customers. However, due to its heterogeneous nature, public exposure, and weak security at low-powered devices, the Smart Grid has vulnerabilities to various malicious threats, adversaries, and cyber attacks, which may affect cost and service availability. Additionally, when the systems' confidentiality, integrity, or availability are compromised, the resulting fallout can threaten national security and have cascading effects on human lives. Given the extreme consequences of an attack, smart-grid technology must be thoroughly tested for correct operation and security {\em before} it is deployed. As a result, vulnerability testing of smart grids, not only for correctness but for security purposes, has been the subject of numerous studies by academics, government agencies, and private companies. This paper reviews the vulnerabilities associated with the smart grid and spotlights simulation as the vulnerability testing methodology conducted in recent pertinent research works. It also presents various security aspects of the smart grid, including grid applications, system and network infrastructure and components, cyber threats and attacks, simulation, and different mitigation techniques. Finally, we analyze the gaps in the current research works, focusing on simulation. We briefly present a real-time simulation testbed that mimics customer behaviour and integrates hardware in the loop to apply attack methods, analyze vulnerabilities and risk mitigation associated with the smart grid system, and propose future work to improve the current framework.

Spectrometers have a wide range of applications ranging from optical to non-optical spectroscopy. The need for compact, portable, and user-friendly spectrometers has been the pivot of attention from small laboratories to the industrial scale. Here, the Czerny Turner configuration-based optical spectrometer simulation design is carried out using ZEMAX OpticStudio. A compact and low-cost optical spectrometer in the visible range has been developed by using diffraction grating as a dispersive element and USB-type WebCAM CCD (Charge-coupled device) as a detector instead of an expensive commercial diffraction grating and detector. Using National Instruments LabVIEW, data acquisition, processing, and displaying techniques are made possible. We have employed different virtual images in LabVIEW programs to collect the pixel-to-pixel information and wavelength-intensity information from the image captured using the WebCAM CCD. Finally, we have shown that the OpticStudio-based spectrometer and experimental measurements of the developed spectrometer are in good agreement.

Air corridors are an integral part of the advanced air mobility infrastructure. They are the virtual highways in the sky for transportation of people and cargo in the controlled airspace at an altitude of around 1000 ft. to 2000 ft. above the ground level. This paper presents fundamental insights into the design of air corridors with high operational efficiency as well as zero collisions. It begins with the definitions of air cube, skylane or track, intersection, vertiport, gate, and air corridor. Then, a multi-layered air corridor model is proposed. Traffic at intersections is analyzed in detail with examples of vehicles turning in different directions. The concept of capacity of an air corridor is introduced along with the nature of distribution of locations of vehicles in the air corridor and collision probability inside the corridor are discussed. Finally, the results of simulations of traffic flows are presented.

Differential equation models to understand interaction between plant and nutrient solution are presented. The root cells selectively emit H+ ions with active transport consuming ATPs to establish electrical gradient along the cell membrane. It establishes electrical field with Nernst potential to make positively charged ions outside the cell membrane flow into the root cell. Anion influx is also modulated by H+ ion concentration because plant root cell absorbs negatively charged particles with symport. If an anion collides with H+ cell to make net charge as neutral, at symport channel, it can flow through. In this paper, mathematical models for cation and anion absorption are introduced. Cation absorption model was induced from Ohm's law combined with Goldman's equation. Anion absorption model is similar to chemical reaction rate model. Both models have physiological terms influenced by gene expression pattern, species or phenotypes. Cation model also includes terms for ion's kinetic and electrical properties, growth of plant and interaction between the root and the surroundings. Simulation for 20 different sets of coefficients showed that the physiology-related coefficient has important role on nutrition absorption tendencies of plants.

We introduce a mission design for an interstellar expedition to nearby earth-like exoplanets, which our analysis determined to be Tau Ceti and Gliese 667C, at the time of analysis in 2013. We review the research problems in propulsion and AGI that must be addressed to launch an AI guided interstellar probe within 100 years. We propose a new semi-autonomous agent approach for intelligent control of the spacecraft. We introduce the concept of a semi-autonomous agent as having built-in safety guarantees that constrain operation. An autonomous agent case study is presented formulating the objective, constraints, AGI implementation of the agent based on Solomono's Alpha architecture, and adding speci city. We discuss the training required to reach human-level and trans-sapient levels of intelligence which corresponds to an entire crew of AI experts specialized in elds such as astrophysics, astromechanics, astrobiology, quantum physics, computer science, molecular biology, and so forth. We project the feasibility of the human-level AI technology based on empirical ndings in neuroscience, and nd that it should be feasible by 2030. We analyze Solomono's in nity point hypothesis in light of Koomey's law about energy eciency of computing and nd that the trends in 2013 indicated an early singularity by 2035, which implies that we might encounter physical bottlenecks which will decelerate computing technology improvements signi cantly. We recommend thus year 2040 for launching the probe by which date other required technologies will have been developed. We discuss the scenario of a virtual crew made of brain simulations, which is a bio-information based AI approach. We detail the subsystems of command and control, communication, scienti c instrumentation, power, propulsion, navigation, and shielding. We propose a variation of ICAN-II/AIMStar propulsion which uses a positron source instead of anti-protons to initiate micro-fusion reactions. We combine the positron initiated fusion pulse propulsion scheme with a miniaturized version of the Daedelus fusion thruster obtaining high performance. We derive two mission pro les one for fusion pulse propulsion, and the yet hypothetical Q-Thruster. Fusion thruster requires 132.2 years for Tau Ceti, and 233.2 years for Gliese 667C, while Q-Thruster takes only 42.3 years for Tau Ceti, and 62.5 years for Gliese 667C. We also discuss extended roles for intelligent interstellar probes such as self-reproduction via nanotechnology, refueling, construction, robotic bodies, and transmission of brain simulations.

This paper shows that by applying the Nyquist-Shannon sampling theorem, the spatial and temporal resolution of a simulation can be no more than half the resolution of the simulating reality. This has significant implications for not only the values of the observables in the simulation but also its physical laws. This progressive halving of nested simulations coupled with the minimum resolution compatible with the production of a simulation also sets a limit to the nestedness of a lineage of simulations (it is by no means infinite). The limit of nestedness is then used to calculate the probability that we are living in a simulation assuming a single base reality. This will be shown to be significantly lower than popular expectation. A Kardashev-like scale, with three variants, is also developed to gauge the technological advancement of a civilization in relation to the extent to which it can extract information from space and time.

Multi-stage hydraulic fracturing with horizontal well technology has been widely used in shale oil reservoir. After hydraulic fracturing, hydraulic fractures and opened beddings are intertwined, which result in a complex fracture network. As well as the migration of multi-phase fluids during fracturing and soaking processes, which lead to complex flowback performance, and brings dif-ficulty to productivity evaluation and flowback strategies optimization. In this paper, taking the Daqing Gulong shale reservoir as an example, a numerical model for flowback period, which considered oil-water-gas three-phase flow and orthogonal fracture network has been established. The characteristics and influencing factors of flowback performance have been deeply studied, and the flowback modes of shale oil are reasonably optimized. Factors such as PTPG (pseu-do-threshold pressure gradient), opened bedding stress sensitivity, opened bedding permeability and matrix permeability have obvious effects on the flowback performance, resulting in signifi-cant variations in production peaks, high yield periods, and decline rates. In addition, three flowback modes are distinguished based on the rate at which the BHP (bottom hole pressure) drops. These correspond to three types of choke modes. Based on the result of numerical model, three flowback modes are optimized and the impacts of different flowback modes on shale oil flowback are clarified. This study is particularly important for understanding the performance of shale oil flowback and guiding the efficient exploitation of shale oil.

The objective of this paper is to investigate the debonding behavior of the interface between continuously and discontinuously fiber reinforced thermoplastics using the climbing drum peel test. The study emphasizes the importance of considering different climatic boundary conditions due to the properties of thermoplastics. Specimens with varying moisture contents are prepared and tested. It is observed that an increase in moisture content initially results in a higher fracture surface energy being required to separate the two materials, but a further increase results in a decrease of the required energy. The study presents an explanatory model of increasing plasticization of the polymer due to increased polymer chain mobility, which results in more deformation energy being required to propagate the crack. The experiment is also modeled numerically for the first time with cohesive surfaces, which successfully reproduces the force-displacement curve in the experiment.