We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

This review will explore the four major pillars required for design and development of an saRNA vaccine: antigen design, vector design, non-viral delivery systems, and manufacturing (both saRNA and lipid nanoparticles (LNP)). In will report on the major innovations, preclinical and clinical data reported in the last five years and will discuss future prospects.

The processability of conductive polymers such as polyaniline (PANI) still poses a challenge due to their properties. The use of stabilizers, compatible and able to interact with PANI, to obtain dispersible and stable colloids is described in this work. To this aim, potato starch has been used as a steric stabilizer for the preparation of polyaniline (emeraldine salt, ES)/starch biocomposites, by exploiting oxidative polymerization of aniline in aqueous solutions containing different ratios of aniline and starch (% w/w). The polyaniline/starch biocomposites were subjected to structural and spectroscopic analyses, thermal analysis, morphological analysis and electrochemical analysis. The samples were then tested for their dispersibility/solubility in various organic solvents. The results showed the formation of PANI/starch biocomposites with an overall smaller size than starch particles, with improved aqueous dispersion and solubility in organic solvents. Although X-ray diffraction and differential scanning calorimetry analyses indicated a loss of crystallinity in the biocomposites, the cyclic voltammetry tests showed that all PANI ES/starch biocomposites display improved redox exchange properties.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

Wide bandgap semiconductors-based photocatalysts are usually limited by their low solar energy conversion efficiency due to their limited absorption solar wavelength, surface’s fast recombination of photoelectron–hole pairs and low charge-carrier mobility. Here we report a new stepwise solution synthesis for making a new photocatalytic core/shell of titanate nanowire/reduced graphene oxide shell (or titanate/rGO) 1D-nanocomposite. The new core/shell nanocomposite maximized the specific surface area, largely reduced the charge transfer resistance and reaction energy barrier, and significantly improved the absorption of the visible light. The core/shell nanocomposites’ large on/off current ratio and rapid photo-responses boosted the photocurrent by 30.0%, the photocatalysis rate by 50.0%, and the specific surface area by 16.4%, when comparing with the pure titanate nanowire core. Our numerical simulations support the effective charge separation on the new core-shell nanostructure, which can help further advance the new photocatalysis.

A new class of nano-cube core-shell heterostructures containing Ag coating on the top of WO₃ was fabricated. Physical vapor deposition was used to produce WO₃ based nano-heterostructures. All kind of wet toxic chemical process was avoided to make the process simple and contaminant free. Sputtering of WO₃ and a subsequent thermal annealing process was done to create nano-cubes of WO₃. After that, sputtering of Ag was performed to form the Ag-WO₃ core-shell nano-heterostructures (CSNH). The CSNHs were characterized using field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD) and UV-vis spectroscopy. The morphologies, elemental analysis, interfaces, crystallinity, phases, and chemical compositions were analyzed. The bottom-up growth of WO₃ nanocubes was studied using different time periods at 900°C. Ag coating was also studied before and after annealing. Finally, an optical property (band gap) was also analyzed using Tauc plot derive from absorption spectra. The tailoring the band gap of WO₃ from ~2.9eV to ~ 2.45 eV was observed while Ag-WO₃ CSNH formed.

As marine traffic is contributing to pollution and mostly have predictable route with repetitive load profiles, to reduce their impact on environment, hybrid system with proton exchange membrane fuel cells (PEMFC-s) and battery pack, is promising replacement. For this purpose, the numerical model of repowered existing vessel that have two diesel engines with 300 kWe is developed. The goal of this paper is to develop numerical model which analyzes and determine equivalent hybrid ship propulsion system for known traveling route. The developed numerical model consists of an interconnected system with PEMFC stack and battery pack as power sources. Numerical model is developed and optimized to meet minimal required power demand for successful route demand, which has variable loads and daily sails six-time same voyage- in total 54 nautical miles. The results have shown that equivalent hybrid power system consists of 300 kWe PEMFC stack and battery pack with 424 kWh battery and state of charge varying between 20 and 87%. To power this new hybrid power system, hydrogen tank of 7200 l holding 284.7 kg at pressure of 700 bar is needed, compared to previous system that spend 1524 kg of diesel and generate 4886 kg of CO2.

Dye/salt separation has gained increasing attention in recent years, prompting the quest for cost-effective and environmentally-friendly raw materials for synthesis high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose structured NF membrane was fabricated by via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-size and finer-size TOCNFs on a microporous substrate, followed by cross-linked with trimesoyl chloride. The resultant TCM membrane possesses a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterials additives. TCM membranes exhibits high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirm the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red, orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.

Waterbomb structures are origami-inspired deformable structural components used in new types of robots. They have a unique radially deployable ability that enables robots to better adapt to their environment. In this paper, we propose a series of new waterbomb structures with square, rectangle, and parallelogram base units. Through quasi-static axial and radial compression experiments and numerical simulations, we prove that the parallelogram waterbomb structure has a twist displacement mode along the axial direction. Compared with the square waterbomb structure, the proposed optimal design of the parallelogram waterbomb structure reduces the critical axial buckling load-to-weight ratio by 55.4% and increases the radial stiffness-to-weight ratio by 67.6%. The significant increase in the radial stiffness-to-weight ratio of the waterbomb structure and decrease in the critical axial buckling load-to-weight ratio make the proposed origami pattern attractive for practical robotics applications.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

Introduction: Atrial fibrillation (AF) is a common cardiac arrhythmia whose prevalence rises with age and is linked to increased morbidity and mortality due to the risk of thromboembolism. Management typically involves anticoagulation and rhythm control, but the treatment of elderly patients with multiple comorbidities requires careful consideration of drug side effects and interactions. Cibenzoline, a Vaughan-Williams class IA antiarrhythmic, is effective against AF but has risks of toxicity, especially in older people and those with renal impairment, due to its renal excretion and prolonged half-life in these populations. Discussion: This paper presents a case of an 80-year-old woman with paroxysmal AF who suffered cardiac arrest due to cibenzoline toxicity despite receiving standard adjusted dosages. The patient's cibenzoline blood concentration was significantly higher than the therapeutic range, leading to cardiotoxicity, which was exacerbated by drug interactions with bisoprolol and edoxaban, both metabolized by the CYP3A4 enzyme. Venoarterial extracorporeal membrane oxygenation (V-A ECMO) and intra-aortic balloon pump (IABP) successfully managed the cardiac arrest. This case emphasizes the unpredictable pharmacokinetics of cibenzoline in elderly patients with renal impairment and the need for vigilant therapeutic drug monitoring to avoid adverse events. Conclusions: Cibenzoline can pose a significant risk of severe toxicity in elderly patients with renal impairment, and drug interactions may potentiate this risk. The paper underscores the importance of careful dose adjustment and monitoring of drug levels in this population. In cases of cibenzoline-induced cardiac arrest, V-A ECMO and IABP are effective treatment modalities. The case study serves as a critical reminder for clinicians to remain vigilant for drug-induced complications and to apply aggressive supportive treatments when necessary.

Dysregulation of cartilage homeostasis and the changes in the density and the architecture of the subchondral bone were postulated as a potent mechanically pathological activity contributing to osteoarthritis (OA) pathogenesis. Extracorporeal shockwave therapy (ESWT) is a new, none invasive and effective method in the treatment of animal OA model. In the current study, we demonstrated that shockwave induced the expression of protein-disulfide isomerase-associated 3 (Pdia-3) which is a multifunctional protein hypothesized to be a significant mediator for 1α,25-Dihydroxyvitamin D3 (1α,25(OH)₂D₃) signaling pathway using two-dimensional electrophoresis. Histological analysis and quantitative polymerase chain reaction (qPCR) were verified and observed that the expression of Pdia-3 at 2 weeks was significantly higher than that of any other group at 4 weeks, 8 weeks, and 12 weeks post-shockwave treatment in early OA knee of rat. The other factors of the 1α,25(OH)₂D₃ rapid membrane signaling pathway including extracellular signal-regulated protein kinases 1 (ERK1), osteopontin (OPG), alkaline phosphatase (ALP), and matrix metallopeptidase 13 (MMP13) were measured and significantly increased by qPCR at 2 weeks post-shockwave treatment in early OA knee. Our proteomic data revealed significant Pdia-3 expression in microenvironments of joint tissue that could be actively responded to ESWT, which may potentially regulate biological function of chondrocytes and osteoblasts in the treatment of OA knee.

This paper seeks to fill in the gaps of modern relativistic Cosmology by utilizing the total symmetry between space and time dimensions and re-interpreting the scale factor of the Universe as a gravitational potential generated by the mass/energy of the entire Universe as a whole. The gradient of this potential is along the cosmological time dimension through which the Universe is falling. This gradient gives us an arrow of time, we find explanations for why the Universe began expanding and why the expansion is accelerating without the need for a Cosmological Constant. In a finite time, the gradient will point in the opposite direction of time turning the expanding Universe into a collapsing one where it is shown that when placing the Schwarzschild metric in the dynamic Cosmological background, gravity becomes repulsive and things like would-be Black Holes become White Holes. The model naturally describes a Universe and an anti-Universe (consisting of antimatter) moving in opposite directions of time that collide at the end of collapse, annihilating and subsequently pair producing two new Universes as the cycle begins again. It is shown that the model's Hubble diagram fits the currently available supernova and quasar data. It is found that Dark Matter can perhaps be understood as ordinary matter that is not connected to us with null geodesics.

Two novel core-shell composites SiO2@PMDA-Si-Tb, SiO2@PMDA-Si-Tb-phen with SiO2 as the core and terbium organic complex as the shell, were successfully synthesized. The terbium ion was coordinated with organic ligand forming terbium organic complex in the shell layer. The bi-functional organosilane ((HOOC)2C6H2(CONH(CH2)3Si(OCH2CH3)3)2 (abbreviated as PMDA-Si) was used as the first ligand and phen as the second ligand. Furthermore, the silica-modified SiO2@PMDA-Si-Tb@SiO2, SiO2@PMDA-Si-Tb-phen@SiO2 core-shell-shell composites were also synthesized by sol–gel chemical route. An amorphous silica shell was coated around the SiO2@PMDA-Si-Tb and SiO2@PMDA-Si-Tb-phen core-shell composites. The core-shell and core-shell-shell composites both exhibited excellent luminescence in solid state. The luminescence of core-shell-shell composites was stronger than that of core-shell composites. Meanwhile, an improved luminescence stability property for the core-shell-shell composites was found in the aqueous solution. The core-shell-shell composites exhibited bright luminescence, high stability, long lifetime, and good solubility, which may present potential applications in the field of bio-medical.

Artificial membrane systems can serve as models to investigate molecular mechanisms of different cellular processes, including transport, pore formation, and viral fusion. However, the current simulacrums such as SUVs, GUVs, and the supported lipid bilayers suffer from issues, namely high curvature, heterogeneity, and surface artefacts, respectively. Freestanding membranes provide a facile solution to these issues, but current systems developed by various groups use silicon or aluminium oxide wafers for fabrication that involves access to a dedicated nanolithography facility and high cost while conferring poor membrane stability. Here, we report the development, characterization and applications of an easy-to-fabricate suspended lipid bilayer (SULB) membrane platform leveraging commercial track-etched porous filters (PCTE) with defined microwell size. Our SULB system offers a platform to study the lipid composition-dependent structural and functional properties of membranes with exceptional stability in a high throughput fashion. With dye entrapped in PCTE microwells by SULB, we show that sphingomyelin significantly augments the activity of pore-forming toxin, Cytolysin A (ClyA) and the pore formation induces lipid exchange between the bilayer leaflets. Further, we demonstrate high efficiency and rapid kinetics of membrane fusion by dengue virus in our SULB platform. Our suspended bilayer membrane mimetic offers a novel platform to investigate a large class of biomembrane interactions and processes.

The catenary shells of revolution are widely used in constructions due to their unique mechanics' feature. However, no publications on this type of shells can be found in the literature. To have a better understanding of the deformation and stress of the catenary shells of revolution, we formulate the principal radii for two kinds of catenary shells of revolution and their displacement type governing equations. Numerical simulations are carried out based on both Reissner-Meissner mixed formulations and displacement formulations. Our investigations show that both deformation and stress response of elastic catenary shells of revolution are sensitive to its geometric parameter $c$, and reveal that the mechanics of the catenary shells of revolution does much better than the spherical shells. Two complete codes in Maple are provided.

The versatile one-pot green synthesis of a highly concentrated and stable colloidal dispersion of AgNPs was carried out using the self-assembled tannic acid without using any other hazardous chemicals. Tannic acid (Plant-based polyphenol) was used as a reducing and stabilizing agent for silver nitrate in a mild alkaline condition. The synthesized AgNPs were characterized for their concentration, capping, size distribution, and shape. The experimental results confirmed the successful synthesis of nearly spherical and highly concentrated (2281 ppm) AgNPs, capped with poly-tannic acid (AgNPs-PTA). The average particle size of AgNPs-PTA was found 9.90 ± 1.60 nm. The colloidal dispersion of synthesized nanoparticles was observed stable for more than 15 months in the ambient environment (25 oC, 65 % relative humidity). The synthesized AgNPs-PTA showed an effective antimicrobial activity against Staphylococcus Aureus Escherichia coli. Ag-PTA also exhibited enhanced catalytic properties. It reduces 4-nitrophenol into 4-aminophenol in the presence of NaBH4 with a normalized rate constant (Knor = K/m) of 615.04 mL·s-1·mg-1. Furthermore, AgNPs-PTA were stable for more than 15 months under ambient conditions. The unique core-shell structure and ease of synthesis render the synthesized nanoparticles superior to others, with potential for large-scale applications, especially in the field of catalysis and biomedical.

In this work, we demonstrate the preparation of easy-to-fabricate nanogranular, strontium ferromolybdate/strontium molybdate core-shell ceramics and examine their properties including tunnel magnetoresistance, magnetic field sensitivity and temperature coefficient of the tunnel magnetoresistance. The tunnel magnetoresistance of nanogranular, strontium ferromolybdate/strontium molybdate core-shell ceramics was modeled yielding values suitable for magnetoresistive sensor application. Such structures possess a narrow peak of magnetic flux sensibility located at about 125 mT. For magnetic flux measurement, single domain granules with superparamagnetic behavior should be applied. The predicted TMR magnetic flux sensitivities for granules with superparamagnetic behavior amount to about 7.7 % per T and 1.5 % per T for granules sizes of 6.8 nm and 4 nm, respectively. A drawback of the tunnel magnetoresistance of such nanogranular core-shell ceramics is the unacceptable large value of the temperature coefficient. Acceptable values, lower than 2 % per K, are obtained only at low temperatures (less than 100 K) or large magnetic flux densities (exceeding 6 T). Therefore, a Wheatstone bridge configuration should be adopted for magnetoresistive sensors design to compensate the effect of temperature.

Membrane-based sensors (MePSs) exhibit remarkable precision and sensitivity in detecting pressure changes. MePSs are commonly used to monitor catalytic reactions in solution, generating gas products crucial for signal amplification in bioassays. They also allow catalyst quantification by indirectly measuring the pressure generated by the gaseous products. This is particularly interesting to detect enzymes in biofluids associated with disease onset. To enhance the performance of a MePS, various structural factors influence membrane flexibility and response time, ultimately dictating the device's pressure sensitivity. In this study, we fabricated MePSs using polydimethylsiloxane (PDMS) and investigated how structural modifications affect the Young's modulus (E) and residual stress (σ0) of the membranes. These modifications have a direct impact on the sensors' sensitivity to pressure variations, observed as a function of the volume of the chamber (Σ) or of the mechanical properties of the membrane itself (S). MePSs exhibiting the highest sensitivities were then employed to detect catalyst quantities inducing the dismutation of hydrogen peroxide, producing dioxygen as gaseous product. As a result, catalase enzyme was successfully detected using these optimized MePSs, achieving a remarkable sensitivity of (22.7 ± 1.2) µm/nM and a limit of detection (LoD) of 396 pM.

Mandibular critical size defect (CSD) due to pathological conditions, trauma, and congenital disease can not heal spontaneously and predominantly filled with fibrous tissue. Therefore, a Guided Bone Regeneration (GBR) combined with bone grafting can be performed. The researchers considered using Demineralized Dentin Material Membrane (DDMM) from bovine dentine as an alternative GBR. This study aimed to determine the amount of fibroblast and collagen density after DDMM and bone graft implantation on CSD. Thirty-six Rattus norvegicus rats were used as samples. Mandibular bone defect 5x5 mm was made, then filled with bone graft and covered with Bovine Pericardium Collagen Membrane (BPCM) in the control group and DDMM in the treatment group. Six samples were sacrificed on 7, 14, and 21 days post-surgical for histology examination. There were no significant differences in the amount of fibroblast and collagen density (p-value > 0,05). The amount of fibroblast is lower and the collagen density is higher in treatment group. DDMM has microporosity to prevent connective tissue ingrowth and dentine tubules to allow growth factors release. DDMM and bone graft implantation can reduce the amount of fibroblasts and increase collagen density of CSD which potentially being used as a CSD alternative treatment for bone regeneration.

Prunus dulcis is one of the most widely cultivated species in the world. Its fruit (almond) is rich in various nutritious and bioactive compounds that exert several beneficial effects. The aim of this study was to determine the chemical profile and evaluate the biological potential in vitro of almond shell extracts. The chemical analysis of shell extracts led to the identification of 15 com-pounds by HPLC-DAD of which 11 were first detected in the almond plant. Twenty-six volatile compounds were identified by the GC-MS technique, among them; seven were firstly detected in the studied plant. For the biological activities, the extracts demonstrated moderate inhibition potential against the antioxidant, antidiabetic, and cytotoxic activities. The methanol extract at 50 µg/mL showed the highest antioxidant (45%) and antidiabetic activities (45% against alpha-glucosidase and 31% against alpha-amylase extracts), while the cyclohexane and dichloromethane at 50 µg/mL showed the highest cytotoxic activity towards Hela (32.2% with cyclohexane), and RAW 264-7 (45% with dichloromethane). Overall, these findings demonstrate the potential of almond shell extracts as a source of bioactive compounds that could be applied in the pharmaceutical and medical fields.

Biological membranes are fascinating. Santiago Ramón y Cajal, who received the Nobel prize in 1906 together with Camillo Golgi for their work on the nervous system, wrote “[..]in the study of this membrane[..] I felt more profoundly than in any other subject of study the shuddering sensation of the unfathomable mystery of life”[1]. The visualization and conceptualization of these biological objects have profoundly shaped many aspects of modern biology, drawing inspiration from experiments, computer simulations, as well as from the imagination of scientists and artists. The aim of this review is to provide a fresh look on current ideas of biological membrane organization and dynamics by discussing selected examples across fields [1] The full quotation is “I must not conceal the fact that in the study of this membrane I for the first time felt my faith in Darwinism (hypothesis of natural selection) weakened, being amazed and confounded by the supreme constructive ingenuity revealed not only in the retina and in the dioptric apparatus of the vertebrates but even in the meanest insect eye. There, in fine, I felt more profoundly than in any other subject of study the shuddering sensation of the unfathomable mystery of life.” from the autobiography Recollections of My Life.

The most common and taught membrane theory assumes that the membrane behaves as a kind of electrical capacitance that is exposed to an electrical current generated by an ionic flow. If this statement is verifiable, it can be confirmed by the laws of physics, mathematics and in particular electricity. We will demonstrate that this hypothesis is not verified and that it is necessary to modify biophysics according to already established and experimentally verified principles of physics.

In the present paper, the comparison is conducted between three classical shell theories as applied to the linear vibrations of single-walled carbon nanotubes (SWCNTs); specifically, the evaluation of the natural frequencies is conducted via Donnell, Sanders and Flügge shell theories. The actual discrete SWCNT is modelled by means of a continuous homogeneous cylindrical shell considering equivalent thickness and surface density. In order to take into account the intrinsic chirality of carbon nanotubes (CNTs), a molecular based anisotropic elastic shell model is considered. Simply supported boundary conditions are imposed and complex method is applied to solve the equations of motion and to obtain the natural frequencies. Comparisons with the results of molecular dynamics simulations available in literature are performed to check the accuracy of the three different shell theories, where Flügge shell theory is found to be the most accurate. Then, a parametric analysis evaluating the effect of diameter, aspect ratio and number of waves along the longitudinal and circumferential directions on the natural frequencies of SWCNTs is performed in the framework of the three different shell theories. Assuming the results of Flügge shell theory as references, it is obtained that Donnell shell theory is not accurate for relatively low longitudinal and circumferential wavenumbers, for relatively low diameters and for relatively high aspect ratios. On the other hand, it is obtained that Sanders shell theory is very accurate for all the considered geometries and wavenumbers, and therefore it can be correctly adopted instead of the more complex Flügge shell theory for the vibration modelling of SWCNTs.

Recently, some authors have developed a shell-less culture system for chick embryos by using a plastic lm as culture vessels. We will show that velocity of rotation of vessels in incubator and temperature have direct relations with growth of chick embryos. We also obtain a mathematical relation between velocity, temperature and rate of growth of chick embryo.

The nucleon-pair shell model (NPSM) with broken symmetry basis is studied. The results demonstrate the validity of NPSM with symmetry broken basis, which leads to a significant reduction in the dimensionality of the multi-pair configuration space. We have observed that the axial-deformed basis provides a satisfactory description of the low-lying spectrum, even without the need for the projection procedure. In the case of the triaxial-deformed basis, we have investigated the variation after angular momentum projection, indicating the potential for NPSM to find exact solutions in the half-closed system.

Low-energy Coulomb excitation is capable of providing unique information on static electromagnetic moments of short-lived excited nuclear states, including non-yrast states. The process selectively populates low-lying collective states and is therefore ideally suited to study phenomena such as shape coexistence and development of exotic deformation (triaxial or octupole shapes). Historically, these experiments were restricted to stable isotopes. However, the advent of new facilities providing intense beams of short-lived radioactive species has opened the possibility to apply this powerful technique to a much wider range of nuclei. We discuss the observables that can be measured in a Coulomb-excitation experiment, their relation to nuclear structure parameters with an emphasis on the nuclear shape, and present some recent examples of Coulomb-excitation studies that provided outcomes relevant for the Shell Model.

In the last 20 years, an increasing number of studies have been reported on membrane active peptides, which exert their biological activity by interacting with the cell membrane either to disrupt it and lead to cell lysis or to translocate through it to deliver cargos into the cell and reach their target. These peptides are attractive alternatives to currently used pharmaceuticals. Antimicrobial peptides (AMPs) and peptides designed for drug and gene delivery currently in the drug pipeline suggest that these membrane active peptides will soon constitute a significant percentage of the drug market. Here, we focus on two most prominent classes of membrane active peptides; AMPs and cell-penetrating peptides (CPPs). AMPs are a group of membrane active peptides that disrupt the membrane integrity or inhibit the cellular functions of bacteria, virus and fungi. CPPs are another group of membrane active peptides that mainly function as cargo-carriers even though they may also show antimicrobial activity to some extent. Biophysical techniques to understand how they interact with the membrane have shed light on the peptide–membrane interaction at various levels of detail. Structural investigation of membrane active peptides in the presence of the membrane provides important clues on the effect of the membrane environment on peptide conformations. Advances in live imaging techniques have allowed examination of peptide action at a single cell or single molecule level. In addition to these experimental biophysical techniques, molecular dynamics simulations provided clues on the peptide-lipid interactions and dynamics of the cell entry process at atomic detail. In this review, we summarize the recent advances in experimental and computational investigation of membrane active peptides with particular emphasis on two amphipathic membrane active peptides, the AMP melittin and the CPP pVEC.

The generation and maintenance of membrane potential is a fundamental part of Membrane Pump Theory. One of the key points of this hypothesis is based on a natural or facilitated molecular diffusion through several types of ion channels and pumps like the Na/K ATPase. Chemistry, physics and especially electrochemistry, however, bring strong contradictions to this theoretical assumption. By respecting the principles of chemistry and electrostatics, it becomes obvious that this theoretical hypothesis cannot work. The ionic diffusion that would be at the origin of this potential cannot take place. Indeed, the topology and the forces involved definitively exclude the current model, which must absolutely be revised according to the current state of our knowledge and allow an advance in the understanding of the phenomena and open new research perspectives.

The exploitation of lipid membranes in biosensors has provided the ability to reconstitute a considerable part of their functionality to detect trace of food toxicants and environmental pollutants. Nanotechnology enabled sensor miniaturization and extended the range of biological moieties that could be immobilized within a lipid bilayer device. This chapter reviews recent progress in biosensor technologies based on lipid membranes suitable for environmental applications and food quality monitoring. Numerous biosensing applications are presented, putting emphasis on novel systems, new sensing techniques and nanotechnology-based transduction schemes. The range of analytes that can be currently detected include, insecticides, pesticides, herbicides, metals, toxins, antibiotics, microorganisms, hormones, dioxins, etc. Technology limitations and future prospects are discussed, focused on the evaluation/ validation and eventually commercialization of the proposed sensors.

In order to alter and adjust the shape of the membrane, cells harness various mechanisms of curvature generation. Many of these curvature generation mechanisms rely on the interactions between peripheral membrane proteins, integral membrane proteins, and lipids in the bilayer membrane. One of the challenges in modeling these processes is identifying the suitable constitutive relationships that describe the membrane free energy that includes protein distribution and curvature generation capability. Here, we review some of the commonly used continuum elastic membrane models that have been developed for this purpose and discuss their applications. Finally, we address some fundamental challenges that future theoretical methods need to overcome in order to push the boundaries of current model applications.

The exploitation of lipid membranes in biosensors has provided the ability to reconstitute a considerable part of their functionality to detect trace of food toxicants and environmental pollutants. Nanotechnology enabled sensor miniaturization and extended the range of biological moieties that could be immobilized within a lipid bilayer device. This chapter reviews recent progress in biosensor technologies based on lipid membranes suitable for environmental applications and food quality monitoring. Numerous biosensing applications are presented, putting emphasis on novel systems, new sensing techniques and nanotechnology-based transduction schemes. The range of analytes that can be currently detected include, insecticides, pesticides, herbicides, metals, toxins, antibiotics, microorganisms, hormones, dioxins, etc. Technology limitations and future prospects are discussed, focused on the evaluation/ validation and eventually commercialization of the proposed sensors.

Metal nanoparticles are used to modify/enhance the properties of a polymer matrix for a broad range of applications in bio-nanotechnology. Here, we study the properties of polymer/gold nanoparticle (NP) nanocomposites through atomistic molecular dynamics, MD, simulations. We probe the structural, conformational and dynamical properties of polymer chains at the vicinity of a gold (Au) NP and a functionalized (core/shell) Au NP, and compare them against the behavior of bulk PE. The bare Au NPs were constructed via a systematic methodology starting from ab-initio calculations and an atomistic Wulff construction algorithm resulting in the crystal shape with the minimum surface energy. For the functionalized NPs the interactions between gold atoms and chemically adsorbed functional groups change their shape. As a model polymer matrix we consider polyethylene of different molecular lengths, from the oligomer to unentangled Rouse like systems. By computing the different properties the concept of the interface, and the interphase as well, in polymer nanocomposites with metal NPs are critically examined. Results concerning polymer density profiles, bond order parameter, segmental and terminal dynamics show clearly that the size of the interface / interphase, depends on the actual property under study. In addition, the anchored polymeric chains change the behavior/properties, and especially the chain density profile and the dynamics, of the polymer chain at the vicinity of the Au NP.

To realize the utilization of peanut shell, this study investigates the combustion behavior, chemical kinetics, and thermodynamic parameters of peanut shell using TGA under atmospheric air. Results indicate that increasing the heating rate leads to higher ignition, burnout, and peak temperatures, as observed in the TG/DTG curves shifting to the right. Analysis of combustion performance parameters suggest that higher heating rates can enhance combustion performances. Kinetic analysis using two model-free methods, KAS and FWO, shows that the activation energy (Eα) ranges from 93.30 to 109.65 kJ/mol for FWO and 89.72 to 103.88 kJ/mol for KAS. The data fit well with coefficient of determination values (R2) close to 1. Pre-exponential factors using FWO range from 2.19×106 to 8.06×107 s–1, and for KAS range from9.72×105 to 2.25×107 s–1. Thermodynamic analysis indicates a low-energy barrier (≤ ±6 kJ/mol) between activation energy and enthalpy changes, suggesting easy reaction initiation. Furthermore, variations in enthalpy (ΔH), Gibbs free energy (ΔG), and entropy (ΔS) upon conversion (α) suggest that peanut shell combustion is endothermic and non-spontaneous, with the generation of more homogeneous or well-ordered products as combustion progresses. These findings offer a theoretical basis and data support for the further utilization of agricultural biomass.

Concrete production requires a significant amount of natural resources, with aggregates comprising between 55% and 80% of the total volume. However, over-exploitation of natural aggregates has led to the exploration of alternative materials for use in concrete production. In this study, crushed hazelnut shells were investigated as a partial replacement for fine aggregate, addressing the problem of natural resource depletion and offering a second use for this important agricultural waste product available in Chile. Hazelnut shells were incorporated in percentages of 2.5%, 5%, and 10% by weight of sand for water-cement ratios of 0.4 and 0.5. The compressive strengths at 7 and 28 days and bending tensile strengths at 28 days were determined, alongside physical properties such as workability, temperature, air content, fresh density, and hardened density of the concrete. Our findings show that replacing 2.5% of the fine aggregate with hazelnut shells led to higher compressive strength at 28 days, exceeding the strength of the standard specimens by 9.5%, whereas replacing 5% of the fine aggregate led to the highest bending tensile strength, exceeding the resistance of the standard specimens by 3.5%. Moreover, the 0.4 w/c ratio consistently led to better results for both compressive and bending tensile resistances, with fewer and lower reductions in mechanical resistances compared to the standard mixture. Our results suggest that concrete mixes with hazelnut shells as a replacement for fine aggregate at a percentage of up to 2.5% can be used in constructive systems with compression strengths lower than 17 MPa, and mixtures with up to 10% hazelnut shell replacement can be used in structures with tensile bending stress requirements lower than 6 MPa. Overall, the use of hazelnut shells as a partial replacement for fine aggregate in concrete production presents an environmentally-friendly and cost-effective solution for the construction industry.

A thin-shell wormhole is crafted by the cut-and-paste method of two Bardeen de-Sitter black holes using Darmois-Israel formalism. Energy conditions are considered for different values of magnetic charge while both mass and cosmological constant are fixed. The attractive and repulsive characteristics of the throat of the thin-shell wormhole are also examined through the radial acceleration. Dynamics and stability of the wormhole are studied around the static solutions of the linearized radial perturbations at the throat of the wormhole. The regions of stability are determined by checking out the condition of concavity of the potential as a function in the throat radius for different values of magnetic charges.

Hepatocellular carcinoma (HCC) is a heterogeneous malignancy with complex carcinogenesis. Although there has been significant progress in the treatment of HCC over the past decades, drug resistance to chemotherapy remains a major obstacle in its successful management. In this study we were able to reduce chemoresistance in cisplatin-resistant HepG2 cells by either silencing the expression of transglutaminase type 2 (TG2) using siRNA or by pre-treatment of cells with the TG2 enzyme inhibitor cystamine. Further analysis revealed that, whereas the full-length TG2 isoform (TG2-L) was almost completely cytoplasmic in its distribution, the majority of the short TG2 isoform (TG2-S) was membrane-associated in both parental and chemoresistant HepG2 cells. Following induction of cisplatin toxicity in non-chemoresistant parental cells, TG2-S together with cisplatin quickly relocated to the cytosolic fraction. Conversely, no cytosolic relocalisation of TG2-S or nuclear accumulation cisplatin was observed following identical treatment of chemoresistant cells, where TG2-S remained predominantly membrane-associated. This suggests that deficient subcellular relocalisation of TG2-S from membranous structures into the cytoplasm may limit the apoptic response to cisplatin toxicity in chemoresistant cells. Structural analysis of TG2 revealed the presence of binding motifs for interaction of TG-S with the membrane scaffold protein LC3/LC3 homologue that could contribute to a novel mechanism of chemotherapeutic resistance in HepG2 cells.

The article focuses on the galvanic replacement synthesis of Ti-Ni and Zr-Ni metal systems with the "core-shell" structure which are potential precursors for intermetallics. The authors defined the effective synthesis parameters and the formation features of polymetallic systems character-ized by granulometric, phase and elemental composition. The X-ray fluorescence and X-ray phase analysis methods showed that the deposition of nickel on dispersed titanium and zirconium leads to the production of test samples with phase composition representing a mechanical mixture of Ni and Ti, Ni and Zr. The method of X-ray fluorescence analysis showed that the presence of hy-drofluoric acid with a 0.5-1.5 M concentration results in the formation of fixed quantitative ratios of elements in the precipitate, which allows the quantitative composition of dispersed systems "titanium - nickel", "zirconium - nickel" to be regulated within a relatively wide range. Scanning electron microscopy proved that all synthesized systems are characterized by a highly porous structure that follows the titanium and zirconium particle surface contour and the presence of spherical nanoscale subunits on the formed particle surface.

In this work, we present a study of ordinary muon capture (OMC) on 136Ba, the daughter nucleus of the 136Xe double beta decay (DBD). OMC rates to low-lying nuclear states (below 1 MeV of excitation energy) in 136Cs are assessed by using both the interacting shell model (ISM) and the proton-neutron quasiparticle random-phase approximation (pnQRPA). We also add the chiral two-body (2BC) meson-exchange currents and use an exact Dirac wave function for the captured s-orbital muon. OMC can be viewed as a complementary probe of the wave functions in 136Cs, the intermediate nucleus of the 136Xe DBD. At the same time OMC can be considered as a powerful probe of the effective values of the weak axial-type couplings in a 100-MeV momentum-exchange region relevant for the neutrinoless DBD. The present work represents the first attempt to compare the ISM and pnQRPA results for the OMC on a heavy nucleus by including also the exact muon wave function and the 2BC. Sensitivity estimates of the present and future neutrinoless DBD experiments will clearly benefit from the future OMC measurements through the OMC calculations similar to the present one.

The generation and maintenance of membrane potential is considered a fundamental element of the cellular machinery. They are based on elements of physics and chemistry. Mathematics is used to validate the equations and evaluate the results. However, this computation process can lead to a misunderstanding of the phenomena involved or to the masking of crucial events. It is even possible that the calculation no longer corresponds to the hypothesis considered. Membrane theory is no exception to these trivial considerations, which are essential for normal theory validation.

Membrane potential generation and maintenance are fundamental parts of membrane theory. However, since its inception, theories and assumptions have remained simple, whereas the amount of knowledge available has only grown. Unfortunately, this simplification and reductionism lead to its loss of validity on both microscopic and macroscopic scales. This article shows that assumptions made outside the context of factual reality lead to contradictions that cannot be compared with science. Membrane theory must be thoroughly revised, taking into account all forgotten and unanswered assumptions and questions to conform to facts and science to maintain credibility.

The membrane potential or resting potential of the neuron has been the subject of many studies. Although this theory explains the generation and maintenance of the membrane potential by direct or even facilitated diffusion, there are too many contradictions to doubt that these forces are sufficient or even at work in a process whose initial conditions are of rare complexity. The aim of this article is to show that already in the past, a competing theory has been developed whose hypothesis seems more scientifically sound. To confirm this last theory, Hirohisa Tamagawa carried out an experiment of great simplicity which makes it possible to invalidate the current theory and to question the teaching and the knowledge in Biology and Biophysics.

There are different treatment options in modern dentistry for the replacement of lost dentition. Of these the most upcoming and acceptable treatment option is Dental implants. The common problem usually with immediate implant placement in the anterior region is the post-operative soft tissue contour as a part of the bone modelling during healing. Hurzeler et al in 2010 introduced a new technique called the “socket shield technique”. This technique has been used as an alternative treatment modality for immediate implant placement in the aesthetic zone.This review articles provides a detailed information regarding the clinical concept of Root membrane technique.

The temperature-dependent intensities of the exciton (X) and biexciton (XX) peaks from single GaAs cone-shell quantum dots (QDs) are studied with micro photoluminescence (PL) at varied excitation power and QD size. The QDs are fabricated by filling of self-assembled nanoholes, which are drilled in an AlGaAs barrier by local droplet etching (LDE) during molecular beam epitaxy (MBE). This method allows the fabrication of strain-free QDs with sizes precisely controlled by the amount of material deposited for hole filling. Starting from the base temperature T = 3.2 K of the cryostat, single-dot PL measurements demonstrate a strong enhancement of the exciton emission up to a factor of five with increasing T. Both, the maximum exciton intensity and the temperature Tx,max of the maximum intensity depend on excitation power and dot size. At an elevated excitation power, Tx,max becomes larger than 30 K. This allows an operation using an inexpensive and compact Stirling cryocooler. Above Tx,max, the exciton intensity decreases strongly up to its disappearance. The experimental data are quantitatively reproduced by a model which considers the competing processes of exciton generation, annihilation, and recombination. Exciton generation in the QDs is given by the sum of direct excitation in the dot plus additional bulk excitons diffusing from the barrier layers into the dot. The thermally-driven bulk-exciton diffusion from the barriers causes the temperature enhancement of the exciton emission. Above Tx,max, the intensity decreases due to exciton annihilation processes. In comparison to the exciton, the biexciton intensity shows an only very weak enhancement, which is attributed to more efficient annihilation processes.

Core-shell particles are heterogenous micro- or nanoparticles with solid, liquid or gas core encapsulated by a protective solid shell. The unique composition of core and shell materials imparts smart properties to the particles. Core-shell particles are gaining increasing attention as tuneable and versatile carriers for pharmaceutical and biomedical applications including targeted drug delivery, controlled drug release, and biosensing. This review first provides an overview of fabrication methods for core-shell particles, followed by a brief discussion on their application and a detailed analysis on manipulation including assembly, sorting, and triggered release. We compile current methodologies employed for manipulation of core-shell particles and demonstrate how existing methods of assembly and sorting micro/nanospheres can be adopted or modified for core-shell particles. Various triggered release approaches for diagnostics and drug delivery are also discussed in detail.

The need for quick and easy deflection calculations of various prefabricated slabs causes that simplified procedures and numerical tools are used more and more often. Modelling of full 3D finite element (FE) geometry of such plates is not only uneconomical but often requires the use of complex software and advanced numerical knowledge. Therefore, numerical homogenization is an excellent tool, which can be easily employed to simplify a model, especially when accurate modelling is not necessary. Homogenization allows for simplifying a computational model and replacing a complicated composite structure with a homogeneous plate. Here, a numerical homogenization method based on strain energy equivalence is derived. Using the method proposed, the structure of the prefabricated concrete slabs reinforced with steel spatial trusses is homogenized to a single plate element with an effective stiffness. There is a complete equivalence between the full 3D FE model built with solid elements combined with truss structural elements and the simplified homogenized plate FE model. The method allows for the correct homogenization of any complex composite structures made of both solid and structural elements, without the need to perform advanced numerical analyses. The only requirement is a correctly formulated stiffness matrix of a representative volume element (RVE) and appropriate formulation of the transformation between kinematic constrains on RVE boundary and generalized strains.

By introducing a variable transformation $\xi=\frac{1}{2}(\sin \theta+1)$, the symmetrical deformation equation of elastic toroidal shells is successfully transferred into a well-known equation, namely Heun's equation of ordinary differential equation, whose exact solution is obtained in terms of Heun's functions. The computation of the problem can be carried out by symbolic software that is able to with the Heun's function, such as Maple. The Gauss curvature of the elastic toroidal shells shows that the internal portion of the toroidal shells has better bending capacity than the outer portion, which might be useful for the design of metamaterials with toroidal shells cells. Through numerical comparison study, the mechanics of elastic toroidal shells is sensitive to the radius ratio. By slightly adjustment of the ratio might get a desired high performance shell structure.

Endothelial cells are the crucial inner lining of blood vessels, pivotal in vascular homeostasis and integrity. However, these cells are perpetually subjected to a myriad of mechanical, chemical, and biological stresses that can compromise their plasma membranes. A sophisticated repair system involving key molecules, such as calcium, annexins, dysferlin, and MG53, is essential for maintaining endothelial viability. These components orchestrate complex mechanisms, including exocytosis and endocytosis, to repair membrane disruptions. Dysfunctions in this repair machinery, often exacerbated by aging, are linked to endothelial cell death, subsequently contributing to the onset of atherosclerosis and the progression of cardiovascular diseases (CVD) and stroke, major causes of mortality in the United States. Thus, identifying the core machinery for endothelial cell membrane repair is critically important for understanding the pathogenesis of CVD and stroke and developing novel therapeutic strategies for combating CVD and stroke. This review summarizes the recent advances in understanding the mechanisms of endothelial cell membrane repair. The future directions of this research area are also highlighted.

The structure of existing activated models is inherently deficient in reflecting the major role of the membrane filtration. This study developed and proposed a novel model, MASM, for the membrane activated process. The effective filtration size imposed by the membrane module, entrapping larger size particles was adopted as the basis of the proposed model. The model defined a modified COD fractionation, accounting for the captured COD fractions as additional model components and utilizing related mass balance relationships. It was implemented for testing the fate of soluble hydrolysable COD and system performance of super-fast membrane activated sludge based on real data for the characterization and process kinetics of domestic sewage and denim processing effluents. Model evaluation was carried for parallel systems with gravity settling and membrane filtration operated at a sludge age range of 0.5-2.0 d. Results reflected significantly better performance of super-fast membrane activated sludge system for both wastewaters, underlining that it was crucially important to account for the captured COD fractions to provide an accurate evaluation of system behavior and effluent quality. This should also be identified as the major shortcoming of the ASM models for evaluating and predicting system performance of activated sludge configurations with membrane separation.

A simple model is developed for membrane fouling, taking into account two main fouling phenomena: cake formation, due to attached solids onto the membrane surface and pores clogging, due to retained compounds inside the pores. The model is coupled with a simple anaerobic digestion model for describing the dynamics of an Anaerobic Membrane BioReactor (AnMBR). In simulations, we investigate its qualitative behavior: it is shown that the model exhibits satisfying properties in terms of flux decrease due to membrane fouling. Comparing simulation and experimental data, the model is shown to predict quite well the dynamics of an AnMBR. The simulated flux best fits the experimental flux with a correlation coefficient r2=0.968 for the calibration data set and r2=0.938 for the validation data set. General discussions are given on possible control strategies to limit fouling and optimize the flux production. We show in simulations that these strategies allow one to increase the mean production flux to 33 L/(h.m2), whereas without control it was 18 L/(h.m2).

Scaffolds for tissue engineering are expected to respond to a challenging combination of physical and mechanical requirements, guiding the research towards the development of novel hybrid materials. This study introduces innovative three-dimensional bioresorbable scaffolds, in which a stiff poly(lactic acid) lattice structure is meant to ensure temporary mechanical support, while a bioactive gelatin-chitosan hydrogel is incorporated to provide a better environment for cell adhesion and proliferation. The scaffolds present a core-shell structure, in which the lattice core is realized by additive manufacturing, while the shell is nested throughout the core by grafting and crosslinking a hydrogel forming solution. After subsequent freeze-drying, the hydrogel network forms a highly interconnected porous structure that completely envelops the poly(lactic acid) core. Thanks to this strategy, it is easy to tailor the scaffold properties for a specific target application, by properly designing the lattice geometry and the core/shell ratio, which are found to significantly affect the scaffold mechanical performance and its bioresorption. Compression stiffness and strength provided by poly(lactic acid) lattices are overall within the range of values displayed by human bone tissue and remain stable after prolonged immersion in water at body temperature for several weeks. On the other hand, the hydrogel undergoes gradual and homogeneous degradation over time, but the core-shell integrity and structural stability are nevertheless maintained during at least 7-week hydrolytic degradation tests. In vitro experiments with human mesenchymal stromal cells reveal that the core-shell scaffolds are biocompatible and their physical-mechanical properties and architecture are suitable to support cell growth and osteogenic differentiation, as demonstrated by hydroxyapatite formation. These results suggest that the bioresorbable core-shell scaffolds can be considered, and further studied, in view of clinically relevant endpoints in bone regenerative medicine.

This article discusses the fabrication of pullulan/polyvinyl alcohol (PVA) and PVA blends as carrier polymers for drug delivery. This study utilized coaxial electrospinning to encapsulate doxorubicin (DOX), a common anticancer drug, within nanofibers, which helped mitigate the adverse effects of DOX on normal cells. The study also demonstrated that the coaxial electrospinning technique using PVA/pullulan cores was effective in inhibiting the attachment and proliferation of HeLa cells, a type of cervical cancer cell. The use of pullulan/PVA and PVA blends as carrier polymers in conjunction with coaxial electrospinning could provide a safe and effective drug delivery system for the treatment of cervical and other solid malignancies. The study concluded that nanofibers showed promising results in inhibiting the growth of HeLa cells, indicating their potential as safe and effective drug delivery systems for treating cervical cancer and other solid malignant tumors.

Biomass is a widely distributed and renewable source of carbon. The main objective of this work is to produce an activated carbon from coconut shells with suitable characteristics to separate CO2 from biogas. The textural characterization of the adsorbent has been determined. Pure component adsorption isotherms of CO2 and CH4 at 30, 50 and 70 °C have been measured. Moreover, the performance of the produced activated carbon, as potential adsorbent for CO2 capture from a CO2/CH4 gas mixture has been evaluated under dynamic conditions in a purpose-built fixed-bed setup.

Extracorporeal membrane oxygenation (ECMO) is used for the management of severe respiratory and cardiac failure, as well as bridge to definite treatment or transplantation. ECMO associated coagulopathy (EAC) is a frequent complication leading to high rates of thrombosis or severe haemorrhage, contributing to morbidity and mortality of patients. Understanding the pathophysiology of EAC is substantial for effectively managing patients on ECMO. We analyse the underlying mechanism of EAC and discuss the monitoring of coagulation profile, combining the viscoelastic point of care assays with the conventional coagulation laboratory tests.

The presented research article shows a functionally graded lattice as an infill structure in designing a 3D printed mechanical element—a bicycle crank arm. The authors want to answer the fundamental question: whether the functionally graded lattice structures can efficiently improve structural performance and how they can be implemented in real complex components. Intuitively, everyone senses that using such elements must bring profit. A good example might be nature, which commonly reaches for such a solution in the skeletons of animals and humans. Two aspects determine their realisations: the lack of adequate construction and analysis methods and the limitations of existing manufacturing methods. Thus, the authors used relatively simple crank arm design and design exploration methods for structural analysis. The design exploration method enabled us to find the optimum solution efficiently. A developed prototype was created utilising additive manufacturing. One of the 3D printing methods - fused filament fabrication technology for metals, allowed the prototype of a crank arm with the optimised infill to be made. As a result, the authors developed a lightweight and manufacturable crank arm showing the new construction and analysis method implementable in similar 3D printed elements.

In this paper, the results of finite element analyses of a single-layer cylindrical latticed shell under severe earthquake is presented. A 3D Finite Element model using fiber beam elements were used to investigate the collapse mechanism of this type of shell. The failure criteria of structural members are simulated based on the theory of damage accumulation. Severe earthquake of peak ground acceleration (PGA) of 500 gal was applied to the shell. The stress and defeomation of the shell were studied in detail. A three-stages collapse mechanism “double-diagonal -members-failure-belt” of this type of structure was discovered. Based on the analysis results, the measures to mitigate collapse of this type of structure is recomanded.

Ras is the most frequently mutated oncogene and recent drug development efforts have spurred significant new research interest. Here we will review progress toward understanding how Ras functions in nanoscale, proteo-lipid signaling complexes on the plasma membrane, called nanocluster. We will discuss how G-domain reorientation is plausibly linked to Ras-nanoclustering and -dimerization. We will then look at how these mechanistic features could cooperate in the engagement and activation of RAF by Ras. Moreover, we will show how this structural information can be integrated with microscopy data that provide nanoscale resolution in cell biological experiments. Synthesizing the available data, we propose to distinguish between two types of Ras nanoclusters, an active, immobile RAF-dependent type and an inactive/ neutral membrane anchor-dependent. We conclude that it is possible that Ras reorientation enables dynamic Ras dimerization, while the whole Ras/ RAF complex transits into an active state. These transient di/oligomer interfaces of Ras may be amenable to pharmacological intervention. We close by highlighting a number of open questions including, whether all effectors form active nanoclusters and whether there is an isoform specific composition of Ras nanocluster.

In the current study nanocellulose was isolated from walnut shell using mechanical and chemical methods. This study highlights the particle size, morphology and these methods’ efficiency in nano structure extraction. The difference between morphology and size of the particles (of the both extracted methods) were investigated by field emission scanning electron microscopy (FESEM). Walnut shell is an agro-waste material with source of lignin and cellulose. Ball mill-ing with different times, in the presence and absence of additive and acid hydrolysis were used as mechanical and chemical methods, respectively. The result showed mechanical method is unable to extract nanoparticle and just reshape the walnut shell. Milling time were also found important in morphology of fiber extracted. FE-SEM images represented that structure mean diameter of using ball mill was 1± 5 μm while hydrolysis acid method extract nano particle with mean diameter of 40± 20 nm.

Calcium dihydrogen phosphate monohydrate [Ca(H2PO4)2·H2O] (a fertilizer) was successfully synthesized by the recrystallization process by using a prepared triple superphosphate (TSP) that derived from oyster shell waste as starting material. This bio-green, eco-friendly process to produce an important fertilizer can promote a sustainable society. The shell-waste-derived TSP was dissolved in distilled water and kept at 30, 50, and 80 °C. Non-soluble powder and TSP solution were obtained. The TSP solution fraction were then dried and the recrystallized products (RCP30, RCP50, and RCP80) were obtained and confirmed as Ca(H2PO4)2·H2O. Whereas the non-soluble products (NSP30, NSP50, and NSP80) were observed as calcium hydrogen phosphate dihydrate (CaHPO4·2H2O). The recrystallized yields of RCP30, RCP50, and RCP80 were found to be 51.0%, 49.6%, and 46.3%, whereas the soluble percentages were 98.72%, 99.16%, and 96.63%, respectively. RCP30 shows different morphological plate sizes, while RCP50 and RCP80 present the coagulate crystal plates. X-ray diffractograms confirm the formation of both the NSP and RCP. The infrared adsorption spectra confirmed the vibrational characteristics of HPO42‒, H2PO4‒ and H2O existed in CaHPO4·2H2O and Ca(H2PO4)2·H2O. Three thermal dehydration steps of Ca(H2PO4)2·H2O (physisorbed water, polycondensation, and re-polycondensation) were observed. Ca(H2PO4)2 and CaH2P2O7 are the thermodecomposed products from the first and second steps, whereas the final product is CaP2O6.

A triangular lattice model for pattern formation by core-shell particles at fluid interfaces is introduced and studied for the particle to core diameter ratio equal to 3. Repulsion for overlapping shells and attraction at larger distances due to capillary forces are assumed. Ground states and thermodynamic properties are determined analytically and by Monte Carlo simulations for soft outer- and stiffer inner shells, with different decay rates of the interparticle repulsion. We find that thermodynamic properties are qualitatively the same for slow and for fast decay of the repulsive potential, but the ordered phases are stable for temperature range depending strongly on the shape of the repulsive potential. More importantly, there are two types of patterns formed for fixed chemical potential - one for a slow and another one for a fast decay of the repulsion at small distances. In the first case two different patterns - for example clusters or stripes - occur with the same probability for some range of the chemical potential. For fixed concentration, an interface is formed between two ordered phases with the closest concentration, and the surface tension takes the same value for all stable interfaces. In the case of degeneracy, a stable interface cannot be formed for one out of four combinations of the coexisting phases, because of a larger surface tension. Our results show that by tuning the architecture of a thick polymeric shell, many different patterns can be obtained for sufficiently low temperature.

Shell nacre from Pinctada species has been extensively researched for managing bone defects. However, there is a gap in the research on using shell nacre as cement with improved physico-chemical properties. To address this, the current study aimed to develop a chemical curable com-posite shell nacre cement (SNC) using shell nacre powder and an organically modified ceramic resin shell nacre containing ladder-structured siloxane methacrylate (SNLSM). Different amounts of shell nacre (24, 48, and 72 weight(wt)%) were added to the SNLSM resin matrix and the effect on the physicochemical properties of the cement was studied. The composite shell nacre cement SNC 72 containing 72 wt% shell nacre exhibited significantly higher mechanical properties (com-pressive strength >100 MPa, flexural strength > 35 MPa) and low linear polymerization shrinkage (0.4%) than other compositions. SNC 72 was radiopaque and the exotherm generated during the curing of the cement was minimal. Direct contact of cured SNC 72 with L929 cells revealed the non-cytotoxic nature of the cement. Overall, the results of the study proved that the composite SNC 72 would be a promising candidate for bone defect management.

The optical properties of the Nafion polymer membrane containing colloidal CdSe/CdS/ZnS nanocrystals embedded by diffusion have been studied. The CdSe/CdS/ZnS nanocrystals have a core/shell/shell appearance. A toluene solution was used to provide mobility of the active sul-fone groups of the Nafion membrane and to embed the nanocrystals inside the membrane. The kinetics of the process of nanocrystal embedding into the membrane matrix was studied using luminescence analysis, absorption spectroscopy and laser emission spectroscopy techniques. The diffusion of colloidal CdSe/CdS/ZnS nanocrystals into the Nafion proton exchange membrane resulted in a new molecular complex «Nafion-colloidal CdSe/CdS/ZnS nanocrystals». The pres-ence of new luminescence centers based on CdSe/CdS/ZnS nanocrystals in the membrane was registered using laser emission spectroscopy. Colloidal nanocrystals located in the Nafion ma-trix represent an analogue of a luminescent transducer. The lines contained in the luminescence spectrum of the membrane, which has been in solution with colloidal nanocrystals for a long time, registered upon its drying, show the kinetics of the formation of the molecular complex «Nafion membrane - nanocrystals». The luminescence spectrum of the membrane with nano-crystals contains additional intensity maxima that do not coincide with the spectral lines of the solvent and Nafion membrane. The intensity of the luminescence spectrum of the membrane with embedded nanocrystals is higher than the intensity of the secondary emission peak of the initial nanocrystals, which is important for the practical use of the complex «Nafion-colloidal nanocrystals» in optical systems.

The air is a fundamental element for the life on Earth. Rapid urbanization and industrialization release large amounts of pollutants (harmful gases, microorganisms, and particulate matter, among others) into the atmosphere, leading to health hazards. Air filtration is still the most used and promising technique for protecting air against pollutants. The quality and efficiency of filtering process are dependent of material used for the filter and other filter’s properties. Several methods can be used for manufacturing filters, one of them uses fibrous membranes obtained through electrospinning from polymeric solutions. Electrospinning is a technique that combines the application of an electrostatic field to a moving fluid which results in the fibers formation. Electrospun membranes are constituted by fibers that the sizes spread on submicro and or nanometric scales. This review focuses on fiber membranes obtained by electrospinning for filtration of particulate matter. It is addressed the effect of solution, processing and ambient parameters on the morphology and dimensional characteristics of fiber membranes. The basic principles of air filtration and test and characterization of filter performance are presented. The research progress on electrospun nanofibers as air filters in recent years is summarized and examined. Finally, conclusion and future perspectives in electrospun fibers for air filtration are provided and discussed.

The generation and maintenance of membrane potential is a fundamental part of Membrane Pump Theory. One of the key points of this hypothesis is based on a natural or facilitated molecular diffusion through several types of ion channels and pumps like the Na/K ATPase. Following the principles of chemistry, electrostatics and geometry, it becomes clear that ion channels cannot function in this way. The ions channels cannot by their location have both a filter function and be ion concentrators, and the Na/K pump by its position in the membrane and by the proposed assumptions is not able to perform its regulatory function. The current model must absolutely be revised according to the current state of our knowledge and allow an advance in the understanding of the phenomena opening new research perspectives.

A new method is proposed to increase rejection in microfiltration by applying membrane oscillation using a new type of microfiltration membranes with slotted pores. The oscillations applied to the membrane surface result in reducing membrane fouling and increasing separation efficiency. An exact mathematical solution of the flow in the surrounding solution outside the oscillating membrane is developed. The oscillation results in appearance of the lift velocity, which moves oil particles away from the membrane. The latter results in both reducing membrane fouling and increasing oil droplets rejection. This developed model was supported by the experimental results for oil water separation in produced water treatment. It was proven that oil droplet concentration reduced notably in the permeate due to the membrane oscillation and that applied shear rate caused by the membrane oscillation is also reduce pore blockage. New generation of microfiltration membranes with slotted pores was used in the experiments.

Production of wastewater related to the oil and gas industries is increasing over the years. The compounds found in industrial wastewater typically show high toxicity, and in this way, they have become a primary environmental concern. Several techniques have been applied in industrial effluents remediation. In spite of the efforts, these techniques are yet ineffective to treat oily wastewater before it can be discharged safely to the environment. Membrane technology is an attractive approach to treat oily wastewater. This is dedicated to the immobilisation of TiO2 nanoparticles on poly (vinylidene fluoride–trifluoro ethylene) (PVDF-TrFE) porous matrix by solvent casting. Membranes with interconnected pores with an average diameter of 60 micrometres and the contact angle of 97°, decorated with TiO2 nanoparticles, are obtained. The degradation of oily wastewater demonstrated the remarkable photocatalytic efficiency of the nanocomposite membranes: under sunlight irradiation for 7 hours, colourless water was obtained. These results show the suitability of TiO2/P(VDF–TrFE) nanocomposite for photocatalytic applications for oily wastewater remediation.

We simulated the glass-blowing process to model a shell resonator, which is a key component in MRIG (Micro Rate Integrating Gyroscope), using the finite elements method to solve a non-isothermal problem. We also calculated the mechanical characteristics of the modeled resonator, including effective mass, eigenfrequencies, angular gain, and energy loss, to predict the resonator's performance as a gyroscope. One key aspect we addressed is the bending of the resonator's rim toward the stem during glass-blowing process. This phenomenon occurs due to increased heat loss at the mold's edge and reduced heat flux at the side of the Gaussian heat source. To mitigate rim bending and the subsequent reduction in capacitance between the rim and 3D electrodes, which can degrade performance in micro glass-blown shell resonators for gyroscopes, we propose two potential mold solutions. The first is using a short-stem mold, which requires extensive polishing to eliminate the bent rim. The second solution is using a mold with a suitable chamfer at the edge, resulting in a straight rim. To quantitatively compare resonators created by these two types of molds, we calculated the noise factor for predicting its gyroscope performance. From these calculations, we find out that using the chamfered mold enables us to increase in the resonator's effective mass, eigenfrequency, angular gain, and quality factor, consequently reducing the noise factor compared to using the short-stem mold. This simulation process will assist us in getting insight into understanding a shell resonator as a gyroscope, designing a mold and determining experimental conditions.

Aquaculture by-products can be compromised an important liming material of increasing soil pH and soil fertility. The aim of this research was to assess the effect of mussel shells on soil pH, on organic matter and on soil nutrients. In this study a pot experiment was carried out at the De-partment of Ichthyology and Aquatic Environment (University of Thessaly, Greece). A acidic soil (pH 4.26) amended with 6 different proportions of mussel shell (0.0, 0.1, 0.3, 0.5, 1, 3 and 6%) in two different grain sizes (Fine powder (>1 mm) and Coarse powder (1-2 mm)), resulting in 13 treatments. According to the results, it was observed that pH, organic matter, Available P and Exchangeable K increased. Specifically, the highest pH values observed at 6% rate. Available P and Exchangeable K achieved the highest content at 6% Fine powder treatment, 46.2 and 190.1 mg kg-1, respectively. Similarly, organic matter had the highest value in 6% Fine powder pots (2.27%). Moreover, Total N concentration varied from 0.11 to 0.14 but no statistically significant different was noticed between the treatments. In conclusion, mussel shells can compose a promising liming material in the agriculture section.

To improve the interfacial compatibility between cement matrix and expanded polystyrene (EPS) in the core-shell lightweight aggregates (CSLA), the effects of sodium silicate, Polyvinyl alcohol (PVA) emulsion, Vinyl acetate-ethylene (VAE) emulsion, acrylic acid, and acetic acid on the cement-EPS interface were investigated. The denseness of the interface was studied by scanning electron microscopy (SEM), and the effect of interfacial agents on the hydration process of cement was studied by the heat of hydration and induction resistivity. The macroscopic properties of the interface of the CSLA were characterized by the "leak-white" rate, drop resistance and numerical crushing strength. The results show that the sodium silicate densifies the interface by generating hydration products on the EPS surface. At the same time, organic acid enhances the interfacial properties of EPS and cement by increasing the surface roughness and allowing hydration products to grow in the surface micropores. In terms of the cement hydration process, both two interfacial agents delay the cement hydration. Above all, with comprehensive interface properties, "leak-white" rate, and mechanical properties, VAE emulsion and sodium silicate can achieve the best performance with a final crushing resistance of 5.7 MPa.

Cashew nut shells (CNS) are the primary waste produced during the processing of cashew nuts; and needs constant attention to handle or valorize these wastes effectively. As a result, these CNS wastes are processed into solid briquettes citing their significant calorific content, thus making them as a promising renewable biofuel for combustion based applications. In most cases, these wastes are pre-treated either through de-oiling or carbonizing prior to compaction, thus removing the harmful hydrocarbons present in them in form of CNS liquids. Presently, this chapter focus on summarising various data related to these CNS wastes and their briquettes in terms of their availability, chemical characteristics, pre-treatment and processing technique, fuel and combustion properties as reported in various literatures. Here, availability depicts the current trend in global consumption of these snack nuts and the proportionate amount of waste shells produced; while, chemical characteristics focused on discussing their anatomy, proximate, lignocellulosic and elemental compositions. Following this, pre-treatment and processing techniques list out the various practises followed to remove CNSL, process de-oiled CNS cakes into bio-char through carbonization, and briquetting of pre-treated CNS wastes along with their compacting techniques prescribed by various researchers. Lastly, fuel and combustion properties brief out about the fuel traits of developed CNS briquettes along with their burning characteristics; and include parameters like proximate and elemental compositions, density and compressive strength, and results related to their combustion and water boiling tests. Moreover, all the reported results and data in this study were in accordance with the international testing standards; and ranged in between their permissible range.

Core-shell structured magnetic nanoparticles combine hard and a soft phases to improve energy efficiency. The mutual interaction of the two phases can lead to the exchange spring effect leading to higher magnetic energy. In this regard, synthesis of Nd2Fe14B based core-shell structured powders have proven to be elusive due to the relatively reactive nature of this phase. In this study, a process has been established for successfully coating the surface of Nd2Fe14B powders with FeCo layer using galvanic displacement method. Initially, a binary phase magnetic powder was synthesized containing Nd2Fe14B and Nd2Fe17 phase. Subsequently, the powders were coated using a Co precursor at 303 K. During coating the metastable Nd2Fe17 phase was dissolved and the Fe ions were released into the solution. Subsequently, the Fe ions deposited together with the Co ions on the surface of Nd2Fe14B powder to form a FeCo shell. The deposited layer thickness and composition was confirmed using TEM analysis.

Single nanowires (NWs) are of great importance for optoelectronic applications, especially solar cells serving as powering nanoscale devices. However, weak off-resonant absorption can limit its light-harvesting capability. Here, we propose a single NW coated with the graded-index dual shells (DSNW). We demonstrate that with appropriate thickness and refractive index of the inner shell, the DSNW exhibits significantly enhanced light trapping compared with the bare NW (BNW), and the NW only coated with the outer shell (OSNW) and the inner shell (ISNW), which can be attributed to the optimal off-resonant absorption mode profiles due to the improved coupling between the reemitted light of the transition modes of the leak mode resonances of the Si core and the nanofocusing light from the dual shells with the graded refractive index. We found that the light absorption can be engineered via tuning the thickness and the refractive index of the inner shell, the photocurrent density is significantly enhanced by 134% (56%, 12%) in comparison with that of the BNW (OSNW, ISNW). This work advances our understanding of how to improve off-resonant absorption by applying graded dual-shell design and provides a new choice for designing high-efficiency single NW photovoltaic devices.

The development of sensors for monitoring Carbon Monoxide (CO) in a large range of temperature is of crucial importance in areas as monitoring of industrial processes or personal tracking using smart objects. Devices integrating GaN/Ga₂O₃ core/shell nanowires (NWs) is a promising solution allowing combining the high sensitivity of the electronic properties to the states of GaN-core surface; and the high sensitivity to CO of Ga₂O₃-shell. Because the performances of sensors primarily depend on the material properties composing the active layer of the device, it is essential to control these properties and in first time its synthesis. In this work, we investigate the synthesis of GaN/Ga₂O₃ core-shell NWs with a special focus on the formation of the shell. The GaN NWs grown by Plasma-assisted molecular beam epitaxy, are post-treated following thermal oxidation to form Ga₂O₃-shell surrounding the GaN-core. We establish that the Ga₂O₃-shell thickness can be modulated from 1 up to 14 nm by changing the oxidation conditions, and follows the diffuse-controlled reaction. By combining XRD-STEM and EDX analysis, we also demonstrate that the oxide shell formed by thermal oxidation is crystalline and presents the β-Ga₂O₃ crystalline phase, and is synthesized in epitaxial relationship with the GaN-core.

This study proposed the combination system consisting of biogas dry reforming reactor and solid oxide fuel cell (SOFC). Since a biogas dry reforming is an endothermic reaction, this study adopted a membrane reactor operated due to the non-equilibrium state with H2 separation from the reaction space. This study aimed to clarify the characteristics of Ni/Cr/Ru catalyst using for a biogas dry reforming membrane reactor. Additionally, this study also investigated the comparison of the characteristics of Ni/Cr/Ru catalyst with that of Ni/Cr catalyst. The impact of operation temperature, the molar ratio of CH4 : CO2, the differential pressure between the reaction chamber and the sweep chamber and the introduction of sweep gas on the characteristics of the biogas dry reforming membrane reactor using Pd/Cu membrane and Ni/Cr/Ru catalyst was examined. The concentration of H2 using Ni/Cr/Ru catalyst was larger than that using Ni/Cr catalyst by 2871 ppmV for the molar ratio of CH4 : CO2 = 1.5 : 1 at the reaction temperature of 600 ℃ and the differential pressure of 0 MPa without a sweep gas, especially. Under this condition, CH4 conversion, H2 yield and thermal efficiency were 67.4 %, 1.77×10-2 % and 0.241 %, respectively.

This study focuses on a biogas dry reforming to produce H2. Biogas contains CO2 of 40 vol% approximately, indicating that the efficiency of the power generation is reduced because of the smaller heating value compared with a natural gas. The authors have proposed the combination system consisting of biogas dry reforming reactor and solid oxide fuel cell (SOFC). Since a biogas dry reforming is an endothermic reaction, this study adopts a membrane reactor which can be operated by causing the non-equilibrium state with H2 separation from the reaction space. This study aims to clarify the impact of thickness of Pd/Cu membrane on the characteristics of the biogas dry reforming membrane reactor using Pd/Cu membrane and Ni/Cr catalyst. The impact of the operation temperature, the molar ratio of CH4:CO2 and the differential pressure between the reaction chamber and the sweep chamber on the characteristics of the biogas dry reforming membrane reactor using Pd/Cu membrane and Ni/Cr catalyst is examined changing the thickness of Pd/Cu membrane. As a result, the highest concentration of H2 is 122711 ppmV which is obtained in case of CH4:CO2 =1:1 at the reaction temperature of 600 ℃ and the differential pressure of 0 MPa using the Pd/Cu membrane whose thickness of 40 m.

membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic hydrophobic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Abstract: membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Autophagy is a cellular mechanism that utilizes lysosomes to degrade its own components and is performed using Atg5 and other molecules originating from the endoplasmic reticulum membrane. On the other hand, we identified an alternative type of autophagy, namely, Golgi membrane-associated degradation (GOMED), which also utilizes lysosomes to degrade its own components, but does not use Atg5 originating from the Golgi membranes. The GOMED pathway involves Ulk1, Wipi3, Rab9 and other molecules, and plays crucial roles in a wide range of biological phenomena, such as the regulation of insulin secretion and neuronal maintenance. We here describe the overview of GOMED, the methods to detect autophagy and GOMED, and to distinguish GOMED from autophagy.

In a large variety of organisms, antimicrobial peptides (AMPs) are primary defences against pathogens. BP100 (KKLFKKILKYL-NH2), a short, synthetic, and cationic AMP, is active against bacteria and displays low toxicity towards eukaryotic cells. BP100 acquires an α-helical conformation upon interaction with membranes and increases membrane permeability. Despite the volume of information available, the mechanism of action of BP100, the selectivity of its biological effects, and its applications are far from consensual. In this work, we synthesized a fluorescent BP100 analog containing naphthalimide linked to its N-terminal end, Napht-BP100 (Napht-AAKKLFKKILKYL-NH2). The fluorescence properties of naphthalimides, especially their spectral sensitivity to microenvironment changes, are well established, and their biological activities against different types of cells are known. A wide variety of techniques were used to demonstrate that a-helical Napht-BP100 was bound and permeabilized POPC and POPG LUV. Napht-BP100, different from that observed for BP100, was bound to, and permeabilized POPC LUV. With zwitterionic (POPC) and negatively charged (POPG) containing LUVs, membrane surface high peptide/lipid ratios triggered complete disruption of the liposomes in a detergent-like manner. This disruption was driven by charge neutralization, lipid aggregation, and membrane destabilization. Napht-BP100 also interacted with double-stranded DNA, indicating that this peptide could also affect other cellular processes in addition to membrane destabilization. Napht-BP100 showed superior antibacterial activity, increased hemolytic activity compared to BP100, and may constitute an efficient antimicrobial agent for dermatological use. By conjugating BP100 and naphthalimide antimicrobial properties, Napht-BP100 was bound more efficiently to the bacterial membrane and could destabilize the membrane and enter the cell by interacting with its cytoplasm- exposed DNA.

Polyvinyl guanidineacetic (PVG) was prepared by the chemical grafting between poly(vinyl alcohol) (PVA) and guanidineacetic acid. The results showed that the guanidineacetic groups were successfully introduced into the polyvinyl alcohol by fourier transform infrared (FTIR) and thermogravimetry (TG). The effects of the amount of catalyst and reaction time on the PVG grafting rate were investigated. The PVG/NWF composite membrane as a heterogeneous catalyst for biodiesel production was successfully prepared by the solvent phase inversion. The effects of mass ratio of methanol/soybean oil and reaction temperature on the conversions using the composite membrane for transesterification were studied. And the reusability of the composite membrane and the kinetics of the reaction catalyzed by the composite membrane were also investigated. The conversions obtained from the model are in good agreement with the experimental data.

African trypanosomes are an early branch in eukaryotic evolution and developed a unique endomembrane system as an adaptation to their parasitic life style. The key virulence mechanism of many pathogens is successful immune evasion to enable survival within the host, which is a feature requiring both genetic events and membrane transport in African trypanosomes. Intracellular trafficking not only plays a role in immune evasion, but also in homeostasis of intracellular and extracellular compartments and interactions with the environment. Significantly, historical and recent work has unravelled some of the connections between these processes and highlighted how immune evasion mechanisms associated with adaptations in membrane trafficking may have, paradoxically, provided specific sensitivity to drugs. Here we explore these advances in understanding the membrane composition of the trypanosome plasma membrane and organelles and provide a perspective for how transport could be exploited for therapeutic purpose.

The global polyvinyldene flouride market is estimated to reach $937,278.5 thousand by 2019, therefore to develop new membranes and gain pioneering ideas, which could create innovative business opportunities, a fundamental knowledge about membrane properties fabricated from recent commercially available PVDF polymers is highly mandatory. In this study, we successfully prepared nine non-woven supported PVDF membranes using a phase inversion precipitation method starting from a 15 wt% PVDF solution in N-methyl-2-pyrrolidone. Various membrane morphologies were obtained by using (1) PVDF polymers with diverse molecular weight in a range from 300.000 Da to 700.000 Da and (2) different temperatures of the coagulation bath (20, 40, and 60 ±2°C) used for the films precipitation. Environmental Scanning Electron Microscope (ESEM) was used for surface and cross-section morphologies characterization. Atomic Force Microscope (AFM) was employed to investigate surface roughness, while Contact Angle (CA) instrument was used for membranes wettability studies. Fourier Transform Infrared Spectroscopy (FTIR) results show that the fabricated membranes are formed by a mixture of TGTG’ chains in α phase crystalline domains and all-TTTT trans planar zigzag chains characteristic to β phase. Moreover, generated results indicate that the phases content and membrane morphologies depend on the polymer molecular weight and conditions used for the membranes preparation. The diversity of fabricated membranes could be applied by the End User Industries for different applications.

Hazelnut (Corylus avellana L.) is of great agroeconomic importance, prized for its nutritional value and antioxidant properties. Its yield and quality may differ due to factors such as season (S), locality (L) and cultivar (C). Our objective was to determine the dynamics of morphological features and antioxidant properties in nuts of Barcelona and Tonda di Giffoni (TDG) cultivars planted at two localities (Cunco and Perquenco) during three productive seasons (S1, S2 and S3). Barcelona grown in Perquenco in S1 and S3 (less precipitation, more solar radiation), performed better than in Cunco with respect to most morphological nut, kernel and shell features, and the same parameters generally had the same trends for TDG in S2 and S3. Among the seasons at the same localities, the differences between the predominant condition defects for both cultivars were in the decreasing order wrinkled/deformed kernels, double kernels, blank and mold ker-nels, with about 75% of hazelnuts without defect. In both cultivars, the shell had higher antioxi-dant properties that increased in S1 and S3 at both localities, and were consistently higher than in the kernels. Lipid peroxidation was higher in the kernel than shell in both cultivars and local-ities for S1 and S3. The results of this study suggest that the different hazelnut cultivar features including physical and chemical components depend on season and locality, which offers im-portant clues for all those interested in the hazelnut industry.

Though the energy density of lithium-ion batteries continues to increase, safety issues related with the internal short-circuit and the resulting combustion of highly flammable electrolyte impede the further development of lithium-ion batteries. It has been well-accepted that a thermal stable separator is important to postpone the entire battery short-circuit and thermal-runaway. Traditional methods to improve the thermal stability of separators includes surface modification and/or developing alternate material systems for separators which may always affect the battery performance negatively. Herein, a thermostable and shrink-free separator with little compromise in battery performance is prepared by coaxial electrospinning and tested. The separator consists of core-shell fiber networks where poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP) layer serves as shell and polyacrylonitrile (PAN) as the core. This core-shell fiber network exhibits little or even no shrinking/melting at elevated temperature over 250 °C. Meanwhile, it shows excellent electrolyte wettability and can take large amount of liquid electrolyte three times more than that of conventional Celgard 2400 separator. In addition, the half-cell using LiNi1/3Co1/3Mn1/3O2 as cathode and the aforementioned electrospun core-shell fiber network as separator demonstrates superior electrochemical behavior, stably cycling for 200 cycles at 1 C with a reversible capacity of 130 mAh g-1 and little capacity decay.

Proton exchange membrane (PEM) fuel cells have emerged as a viable alternative energy production source for stationary and transportation applications. Reliable and sustainable fuel cell operation requires effective water management. Membrane water content can vary along the stack during transients which can lead to losses in fuel cell performance. To control these variations a model that predicts the internal humidity dynamics of the stack is needed. In this study, a control-oriented model for predicting membrane water content variation was developed and implemented in MATLAB/Simulink. A lumped parameter model was initially developed and then further discretized into smaller control volumes to track humidity distribution along the stack. To validate the model’s predictions, the predicted results were compared to computer simulation results from GT-Suite. The root mean square error (RMSE) between the model’s prediction and GT-Suite’s simulation results was found to be within 1.5 membrane water content for all cases, demonstrating the model’s capability to capture the variation of membrane water content along the stack. The developed model will be useful for real-time control of membrane water content variation in PEM fuel cells.

Water electrolysis is a highly efficient route to produce ideally clean H2 fuel with excellent energy conversion efficiency and high gravimetric energy density, without producing carbon trace unlike steam methane reforming, and resolves the issues of environmental contamination via replacing the conventional fossil fuel. Of special importance lies in the advancement of highly effective non-precious catalysts for the oxygen evolution reaction (OER). The electrocatalytic activity of an active catalyst mainly depends on the material conductivity, accessible catalytically active sites, and intrinsic OER reaction kinetics, which can be tuned via introducing heteroatom N in the catalyst stricture. Herein, an efficacious nitrogenation of CuS has been accomplished, which was synthesized using hydrothermal procedure, and characterized for their electrocatalytic activity towards OER. The nitrogen-doped CuO@CuS (N,CuO@CuS) electrocatalyst exhibits superior OER activity than pristine CuS (268 and 602 mV), achieving the low overpotential of 240 and 392 mV at a current density of 10 and 100 mA/cm2, respectively, ascribed to the favorable electronic structural modification triggered by nitrogen incorporation. The N,CuO@CuS also exhibits excellent endurance under varied current rates and a static potential response over 25 h stability measured at 10 and 100 mA/cm2.

Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.

Sperm cells must undergo a complex maturation process after ejaculation to be able to fertilize an egg. One component of this maturation is hyperpolarization of the membrane potential to a more negative value. The ion channel responsible for this hyperpolarization, SLO3, was first cloned in 1998, and since then much progress has been made to determine how the channel is regulated and how its function intertwines with various signaling pathways involved in sperm maturation. Although SLO3 was originally thought to be present only in the sperm of mammals, recent evidence suggests that a primordial form of the gene is more widely expressed in some fish species. As with many reproductive genes, SLO3 is rapidly evolving with low conservation between closely related species and different regulatory and pharmacological profiles. Despite these differences, SLO3 appears to have a conserved role in regulating sperm membrane potential and driving large changes in response to stimuli. As with the differences in regulation of the channel, the effect of this hyperpolarization of the membrane potential may vary among mammalian species. Recent discoveries have elucidated the role of SLO3 in these processes in human sperm and provided tools to target the channel to affect human fertility.

Although there is a common physiological notion that the origin of the membrane potential is attributed to transmembrane ion transport, it is theoretically possible to explain its generation by the mechanism of ion adsorption. It was previously suggested that the ion adsorption mechanism led even to the potential formulas which are even identical to either the famous Nernst equation or Goldman-Hodgkin-Katz equation. Our further analysis shown in this paper indicates that the potential formula based on the ion adsorption mechanism leads to one equation which is the function of material surface charge density and the material surface potential. Furthermore, we confirmed that the equation holds in all the different experimental systems we studied. Although we have not succeeded in elucidating why such an equation is established, the equation appears to be the key equation governing the characteristics of the membrane potential regardless of the systems in question.

Accurate prediction of the membrane potential by membrane theory is possible on the basis that the plasma membrane is selectively permeable to ions and that permeability determines the characteristics of the membrane potential. However, an experimental and artificial cell system with an impermeable membrane serving as a model plasma membrane has a non-zero membrane potential, and this potential generated across the membrane is somehow consistent with the potential characteristics predicted by the membrane theory, despite the impermeability of the membrane to ions. A long-forgotten theory, called the association-induction hypothesis (AIH), has emerged as a more plausible mechanism for generating the membrane potential than the membrane theory to explain this unexpected behavior. The AIH asserts that ion-selective membrane permeability is not necessary for the generation of the membrane potential, which is contrary to the membrane theory. Although such an idea is not easy to accept, the experimental results clearly suggest the correctness of the AIH.

An embryonic version of membrane theory can be date back to the Bernstein's work reported more than a hundred years ago. Such an originally old work has evolved conceptually and mathematically up until today, and it plays a central role in current membrane theory. Goldman-Hodgkin-Katz equation (GHK eq.) is one of the math-based monumental works, which constitutes the present membrane theory. Goldman theoretically derived GHK eq., but its physiological meaning was provided by the two renowned scientists, Hodgkin and Katz. These two employed an assumption that the electric field (EF) across the plasma membrane is constant to validate the GHK eq. physiologically. Proposal of Hodgkin-Huxley model (HH model) is another math-based monumental works developed from the membrane theory and now forms a fundamental part of the current membrane theory. GHK eq. and HH model are quite fundamental central concepts in the current physiology. Despite the broad acceptance of GHK eq. at present time, its prerequisite that the EF within the plasma membrane is constant is hardly believable. Especially when the action potential is generated, it sounds totally nonsense. Furthermore, the existence of constant EF within the plasma membrane is conceptually almost in conflict with the HH model. The authors will discuss those problematic issues the membrane theory inherits.

In this paper, we present a finite element simulation of an adaptive piezoelectric fluid-membrane lens modeled in COMSOL Multiphysics. The simulation couples the piezoelectric effect with the fluid dynamics to model the interaction between piezoelectric forces and fluid forces. Also, the simulation is extended to model the thermal expansion of the fluid. Finally, we compare the simulation and experimental results of the adaptive lens refractive power at different actuation levels and temperatures.

Water electrolysis provides efficient and cost-effective production of hydrogen from renewable energy. Currently, the oxidation half-cell reaction relies on noble-metal catalysts, impeding widespread application. In order to adopt water electrolyzers as the main hydrogen production systems, it is critical to develop inexpensive and earth-abundant catalysts. This review discusses the proton exchange membrane (PEM) water electrolysis (WE) and the progress in replacing the noble-metal catalysts with earth-abundant ones. Researchers within this field are aiming to improve the efficiency and stability of earth-abundant catalysts (EACs), as well as to discover new ones. The latter is particularly important for the oxygen evolution reaction (OER) under acidic media, where the only stable and efficient catalysts are noble-metal oxides, such as IrO_x and RuO_x. On the other hand, there is significant progress on EACs for the hydrogen evolution reaction (HER) in acidic conditions, but how many of these EACs have been used in PEM WEs and tested under realistic conditions? What is the current status on the development of EACs for the OER? These are the two main questions this review addresses.

A membrane ozonation contactor was built to investigate ozonation using tubular membranes and to inform computational fluid dynamics (CFD) studies. Non-porous tubular polydimethylsiloxane (PDMS) membranes of 1.0 – 3.2 mm inner diameter were tested at ozone gas concentrations of 110 – 200 g m−3 and liquid side velocities of 0.002 m s−1 – 0.226 m s−1. The dissolved ozone concentration could be adjusted to up to 14 mg O3 L−1 and increased with decreasing membrane diameter and liquid side velocity. Experimental mass transfer coefficients and molar fluxes of ozone were 1.1∙10−5 mol m−2 s−1 and 2.4∙10−6 m s−1, respectively, for the smallest membrane. CFD modelling could predict the final ozone concentrations but slightly overestimated mass transfer coefficients and molar fluxes of ozone. Model contaminant degradation experiments and UV absorption measurements of ozonated water samples in both ozone (O3) and peroxone (H2O2/O3) reaction systems in pure water, river water, wastewater effluent and solutions containing humic acid show that the contactor system can be used to generate information on the reactivity of ozone with different water matrices. Combining simple membrane contactors with CFD allows predicting ozonation performance under a variety of conditions leading to improved bubble-less ozone systems for water treatment.

Curcumin has restrained clinical applications due to poor bioavailability. This study aimed to synthesize cockle shell-derived calcium carbonate (aragonite) nanoparticles (CSCaCO3NP) for delivery of curcumin and to evaluate its kinetic release in vitro. CSCaCO3NP was synthesized and conjugated with curcumin (Cur-CSCaCO3NP) using a simple top down approach and characterized for its physicochemical properties as a potential curcumin carrier. In vitro release profile was assessed using dialysis bag membrane method. The release data were fitted to Korsmeyer-Peppas, Zero order and Higuchi models to evaluate the mechanism of release pattern. A spherical shaped CSCaCO3NP with a surface area of 14.48±0.1 m2/g, average mean diameter size of 21.38±2.7 nm and a zeta potential of -18.7 mV was synthesized which has a high loading content and encapsulation efficiency. The FT-IR and XRD revealed less observable changes on the peaks after conjugation. In vitro kinetic release profile demonstrated sustained release and best fitted to the Higuchi equation model. The results of this study showed the capacity of the synthesized CSCaCO3NP to encapsulate curcumin efficiently with a stable release in vitro. This could give an insight and supportive ideas on the potentials of CSCaCO3NP for curcumin delivery. Therefore, CSCaCO3NP holds future prospects in preclinical framework to enhance curcumin efficacy for oral therapeutic applications.

During HVDC earth return operation systems, a high magnitude current will be injected into soil through earth electrode, the potential on the surface would change widely and produce unfavorable effects on the AC systems around. This paper presents an effective finite element method (FEM) coupling electric field with thermal field to evaluate the electrical field induced by the injected DC current. Firstly, owe to the characteristic of FEM, this method can consider arbitrary soil and earth electrode structure. Secondly, by setting the electrical and thermal parameters of soil as a function of temperature at the same time, the dynamic coupling process of electric field and thermal field is simulated accurately. Thirdly, to deal with the singular point in FEM subdivision and the huge computation in traditional three-dimensional FEM, the FEM coupling 2-D earth electrode with 3-D soil based on "shell" theory is introduced. Finally, based on the suggested method, the effect of abnormal resistance region (ARR) near DC earth electrode on electric field distribution is analyzed.

Pyrolysis is a thermochemical conversion process designed for biomass decomposition in an oxygen-free environment. It typically operates within a temperature window of 200 to 800°C and generates various byproducts, including gases, liquid fractions (both aqueous and organic) such as bio-oil, and solids like char. Bio-oil is a significant product of pyrolysis. It is characterised by a complex blend of organic compounds. The acidic nature of bio-oil primarily originates from volatile acids, such as acetic acid. The recovery of acetic acid from bio-oil facilitates the use of the extracted substance as a precious resource, hence enhancing its significance in the framework of a circular bioeconomy. Acetic acid finds widespread application in manufacturing commercially important chemicals like vinyl acetate monomers and formulating phytosanitary products due to its inherent herbicidal and antifungal properties. However, to be used, acetic acid has to be separate from the raw bio-oil. Separation methodologies, including nanofiltration and reverse osmosis, demonstrate potential in recovering acidic constituents from bio-oil due to their high selectivity and effective system management. This article offers a concise review about acetic production from lignocellulosic biomass from pyrolysis and its recovery through various membrane separation processes.

Although a slightly radioactive element, thorium is considered very toxic because its various species, which reach the environment, can constitute an important problem for the health of the population. The present paper aims to expand the possibilities of using membrane processes in the removal, recovery and recycling of thorium from industrial residues reaching the municipal waste processing platforms. The paper includes a short introduction on the interest shown for this element, a weak radioactive metal, followed by highlighting of some common (domestic) uses. In a distinct but concise part, the bio-medical impact of thorium is presented. The classic technologies for obtaining thorium are concentrated in a single schema, and then the speciation of thorium is presented with an emphasis on the formation of hydroxo-complexes and complexes with common organic reagents. The determination of thorium has been highlighted both on the basis of its radioactivity, but especially through methods that call for extraction followed by an established electrochemical, spectral or chromatographic method. Membrane processes are presented based on the electrochemical potential difference, rapidly presenting barro-membrane processes, electrodialysis, liquid membranes and hybrid processes. A separate sub-chapter is devoted to proposals and recommendations for the use of membranes in order to achieve some progress in urban mining for the valorization of thorium.