Electroless etching of semiconductors was elevated to an advanced micromachining process by the addition of a structured metal catalyst. Patterning of the catalyst by lithographic techniques facilitates the patterning of crystalline and polycrystalline wafer substrates. Galvanic deposition of metals on semiconductors has a natural tendency to produce nanoparticles rather than flat uniform films. This characteristic makes possible the etching of not only wafers but also particles with arbitrary shape. While it has been widely recognized that spontaneous deposition of metal nanoparticles can be used in connection with etching to porosify wafers, it is also possible to produced nanostructured powders. MACE can be controlled to produce (1) etch track pores with shapes and sizes closely related to the shape and size of the metal nanoparticle, (2) hierarchically porosified substrates exhibiting combinations of large etch track pores and mesopores, and (3) nanowires with either solid or mesoporous cores. This review discussed the mechanisms of porosification, processing advances and the properties of the etch product with special emphasis on the etching of silicon powders.

Optical biopsy describes a range of medical procedures in which light is used to investigate disease in the body, often in hard-to-reach regions via optical fibres. Optical biopsies can reveal a multitude of diagnostic information to aid therapeutic diagnosis and treatment with higher specificity and shorter delay than traditional surgical techniques. One specific type of optical biopsy relies on Raman spectroscopy to differentiate tissue types at the molecular level and has been used successfully to stage cancer. However, complex micro-optical systems are usually needed at the distal-end to optimise the signal-to-noise properties of the Raman signal collected. Manufacturing these devices remains a critical challenge, particularly in a way suitable for large scale adoption. In this paper, we describe a novel fibre-fed micro-optic system designed for efficient signal delivery and collection during a Raman spectroscopy based optical biopsy. Crucially, we fabricate the device using a direct-laser-writing technique known as ultrafast laser assisted etching which is scalable and allows components to be aligned passively. The Raman probe has a sub-millimetre diameter and offers confocal signal collection with 71.3 ± 1.5% collection efficiency over a 0.8 numerical aperture. Proof of concept spectral measurements were performed on mouse intestinal tissue and compared with results obtained using a commercial Raman microscope.

Some contaminants of emerging concern (CECs) are known to survive conventional wastewater treatment plants, which introduce them back to the environment and can potentially cycle up in drinking water supplies. This is especially concerning because of the inherent ability of some CECs to induce physiological effects in humans at very low doses. Advanced oxidation processes (AOPs) such as TiO2 based photocatalysis are of prominent interest for addressing CECs in aqueous environments. Natural water resources often contain dissolved metal cations concentrations in excess of targeted CEC concentrations. These cations may significantly, adversely impact degradation of CECs by scavenging TiO2 surface generated electrons. Consequently, simple pseudo first order or Langmuir-Hinshelwood kinetics are not sufficient for reactor design and process analysis in some scenarios. Rhodamine B dye and dissolved copper cations were studied as reaction surrogates to demonstrate that TiO₂ catalyzed degradation for very dilute solutions is very nearly completely due to homogeneous reaction with hydroxyl radicals and that in this scenario the hole trapping pathway has negligible impact. Chemical reaction kinetic studies were then carried out to develop a robust model for RB/metal reactions that is exact in the electron pathways for hydroxyl radical production and metal scavenging.

Novel Ca3(BTC)2 metal-organic frameworks with different sizes and shapes constructed by Ca2+ and trimesic acid as metal center and ligands respectively were synthesized by a surfactant-assisted method. The relationship between the quantity of surfactant and the particle morphology of the product have been further studied. The samples were characterized by scanning electron microscope, powder X-ray diffraction and Inductively coupled plasma mass spectrometry. The results indicated that the size and shape of Ca3(BTC)2 could be regulated by changing the quantity of surfactant. Rod- and sheet-like Ca3(BTC)2 MOFs have been readily availabled. The removal kinetics of heavy metals of Pb(II) were also studied by rod-like Ca3(BTC)2. The results showed that as-synthesized Ca3(BTC)2 could effectively remove heavy metals of Pb(II) from the sewage.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

Keywords: liquid alloys, microstratification, dispersed particles, spontaneous dispersion, criteria for true (entropic) spontaneous dispersion, mechanisms of quasi-spontaneous dispersion, methods and results for assessing size of dispersed particles.

Transparent and high-hardness materials have become the object of wide interest. Most notably, it concerns technical glasses and crystals. A notable example is a sapphire – one of the most rigid materials having impressive mechanical stability and good optical properties. Nonetheless, using this material for 3D micro-fabrication is not straightforward due to its brittle nature. On the microscale, selective laser etching (SLE) technology is an appropriate approach for such media. Therefore, we present our research on c-cut crystalline sapphire microprocessing by using femtosecond radiation-induced SLE. Here we demonstrate a comparison between different wavelength radiation (1030 nm, 515 nm, 343 nm) usage for modification inscription and various etchants (Hydrofloridic acid, Sodium Hydroxide, Potassium Hydroxide and Sulphuric and Phosphoric acid mixture) comparison. We show that regular SLE etchants such as Hydrofluoric acid or Potassium Hydroxide are unsuitable materials for selective sapphire laser etching. Meanwhile, a 78% sulphuric and 22% phosphoric acid mixture at 270°C temperature is a good alternative for this process. We present the changes in the material after the separate processing steps. Finally, a protocol for advanced sapphire structure formation and a few exemplary structures are presented.

Reductive amination is a powerful tool in sustainable organic synthesis that allows chemists to access a wide range of valuable amine products using renewable feedstocks, mild reaction con-ditions, and with minimal waste generation. Practical applications can be found in various fields, including pharmaceuticals, contributing to greener and more sustainable chemical processes. In this work we present a heterogeneous (Rh and Pt) catalysed protocol for the fast and efficient synthesis of ractopamine hydrochloride (-adrenergic drug) under MW-assisted reductive ami-nation protocol starting from raspberry ketone and octapamine. Microwave (MW) successfully accelerated the hydrogenation reaction and reduced the reaction time from 13 hours to only 3 hours under mild conditions (50°C at 10 bar). The best catalysts were Pt/C and Rh/C, which led to high conversion and selectivity towards ractopamine:HCl. The solvent has a significant effect on the reaction outcome. The replacement of methanol with other solvents had a negative impact on the reaction yield. We also replaced the raspberry ketone with other ketone substrates, especially cyclohexanone. These preliminary experiments may be useful for further process improvements in the synthesis of β-adrenergic agonists and related structures.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

How to effectively suppress thermal cracks in the metal laser additive manufacturing process is still one of the key issues to be solved in the field of laser additive manufacturing. Metal tin, with wide liquid phase working temperature range, high boiling point, low viscosity, high thermal conductivity and excellent electrical conductivity. The use of tin as an auxiliary thermal management material in the metal additive manufacturing process is expected to achieve effective regulation of the temperature field and stress field of the formed part, thereby inhibiting the initiation of cracks and obtaining formed parts with the target grain structure and high reliability. This paper presented a novel liquid metal-assisted laser additive manufacturing method (LMAAM). A numerical model for the laser additive manufacturing of tin-assisted titanium alloys was established. The differences of the flow field, temperature field and stress field of the formed parts with tin and without tin were compared and analyzed. The influence of the interaction position between the tin liquid level and the forming part on the temperature field and stress field of the forming part was deeply studied. The laser additive manufacturing experiment of tin-assisted titanium alloy was carried out, and the experimental results were basically consistent with the simulation results, which verified the validity of the model. LMAAM technology has proven to be an effective method for additive manufacturing of highly reliable formed parts.

Polyhydroxyalcanoates (PHAs) are biodegradable polymers synthesized in cytoplasmic granules in bacteria, such as Cupriavidus necator (Ralstonia eutropha), Alcaligenes latus, Pseudomonas spp., Comamonas spp. and other species. PHAs accumulation occurs in response to stress conditions, i.e. under high carbon and low nitrogen (24:1 ratio). PHA can be synthesized using recombinant microorganisms (provided with the operon phbA/phbB/phbC), escaping the constrains of nutrient request, except addition of high amount of sugar (glucose, lactose, fructose). In this study; E. coli was genetically modified for PHB production in biofermentors. The production of PHA at industrial scale requires a continuous supplementation of fermentable sugars to support the availability of nutrients and to assess the level of the exponential growth phase; since sugars are required either for bacterial growth either for PHA synthesis and energy storage. The biofermentors need to be run in automated system. Sensors are used at many points in fermentators; in the evaluation of parameters: consumption of sugars; cell density; quantification of PHB synthesis. The need of operational control during the fermentation has prompted us to application of three measurements; one unit linked to a Nanodrop to evaluate OD; one linked to a reaction chamber to measure sugars consumed by enzyme based fluorescence detection; and one for bacteria Nile Blue staining and fluorescence intensity reads. The growth of bacteria on three different plant by-products was monitored and PHB production in four days using a banana by-product feed was optimised. These detectors will make possible to exploit the full potential of bioreactors optimizing the time of use and maximizing the number of bacteria synthesizing PHA.

Excitation of the acoustic field leading to the Blaha effect affects the plasticity of the material significantly in ultrasonic vibration-assisted forming. In a micro-forming field, the effects are more significant in the deformation in surface of materials [1]-[3], in which reduction of the surface roughness based on the increasing of plastic deformation of surface asperity was effective [4]. On the other hand, the effect on deformation behavior of the bulk region indicted reduction in the yield stress of materials, and not only acoustic effect [5], but also impact effect is found to generate a large amount of dislocation and produce plastic deformation [6][7]. However, the effect on the bulk is more significant as that on the surface. Differences in the effect on the surface and the bulk are not clarified. In this study, the mechanism of the deformation in the surface of the material with ultrasonic vibration assistance is investigated and compared with that in the bulk. Forging tests using a newly developed ultrasonic vibrator were carried out on pure Cu foils with various process conditions. The longitudinal vibration frequency of the ultrasonic transducer is 60∓2kHz, and the vibration amplitude is in an adjustable range of 0~10μm. Forging test was carried out at different initial stress, specimen size and amplitude. The difference in acoustic softening and impact effects on the surface and the bulk was discussed.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

Among the various types of gas sensors, the chemoresistive gas sensors based on metal oxides are considered the most attractive ones due to their simple operation, low costs and miniaturization. Thin films of V2O5 undoped and doped with TiO2 were studied as nitrogen dioxide, methane and hydrogen sensors. The experimental kinetics of the electrical conductivity changes due to introduction and removal of gas on metal oxide gas sensors were successfully explained in terms of the Langmuir adsorption theory.

Solvent free copolymerization of epoxides derived from fatty acid esters of waste cooking oil with phthalic anhydride using (salen)CrIII Cl as catalyst and n-Bu4NCl/DMAP as co-catalyst was carried out for the first time under microwave irradiation, where reaction time was reduced from number of hours to minutes. The polyesters were obtained with molecular weight (Mw = 3084-6740 g/mol) and dispersity values (D = 1.18-1.92), when (salen)CrIII Cl/n-Bu4NCl was used as catalysts. While in case of DMAP as a co-catalyst, polyesters with improved molecular weight (Mw = 5537-6925 g/mol) and narrow dispersity values (D = 1.07-1.28) were obtained even at reduced concentrations of (salen)CrIII Cl and DMAP. The obtained products were characterized and evaluated by attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR), proton nuclear magnetic resonance (1H-NMR) spectroscopy, gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) Techniques.

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

This research study focuses on addressing practical optimization challenges in audio-visual content using advanced computational intelligence methods, with a specific emphasis on privacy-preserving issues. The research will be presented as a proposal and can be conducted based on the provided ideas. Computational intelligence encompasses various approaches, including evolutionary algorithms, learning methods, fuzzy systems, and neural networks, which have become essential tools for tackling complex engineering optimization problems due to computational expenses, dimensional complexities, and interdisciplinary integration. The research objectives include a thorough investigation of optimization challenges in audio-visual content, the delineation of problem characteristics, and the development of relevant methodologies based on these specifications. The main goals of the study, titled "Advanced Computational Intelligence Assisted Less-Expensive Privacy-Preserving Optimization," encompass the development of a metamodel-based learning algorithm integrated with evolutionary computation for privacy-preserving optimization, less-expensive signal watermarking optimization using hybrid metamodeling and evolutionary algorithms, and a closed-loop robust intelligent PID control system applied in real-time dynamic signal watermarking. Additional objectives may be defined as the research progresses and further background review is conducted.

Semisolid casting can provide excellent castings, but the nature of the pore-forming mechanisms has not been properly clarified. In the current communication, it was suggested that hydrogen precipitated during slurry making might have a decisive role in the formation of both gas and shrinkage porosity. Intensive stirring at the end of the slurry making process may act as a degassing step. Without the intense stirring, structures of primary slurry particles form around the hydrogen pores, strongly affecting pore formation and feeding during the intensification stage.

Heavy metal pollution poses a significant threat to ecosystems and human health worldwide. In response to this pressing issue, bioremediation has emerged as a promising approach for mitigating contamination. This paper adopts a bibliographic method to explore the key techniques and applications of bioremediation. Furthermore, we delve into the most prominent threats to human environmental health and the corresponding remediation methods. Additionally, we discuss the future trajectory of bioremediation research, with a particular focus on the integration of big data and machine learning technologies. These advanced methodologies hold great potential for enhancing the effectiveness and efficiency of environmental remediation efforts in the face of escalating pollution challenges.

In the present work, diamond films have been grown on GaN-on-Sapphire substrates by chemical vapor deposition (CVD) with the addition of nitrogen to the standard H2/CH4 precursor recipe. Diamond on GaN materials processing is not straight-forward, as GaN is susceptible to a quasi-pure hydrogen CVD plasma etching. 1%, 3% and 5% N2 gas was gradually added to the H2 gas with fixed 6% CH4 in the recipe to promote the growth of diamond nanocrystals. Different types of microstructures were produced, with addition of nitrogen to the precursor gas recipe. Nitrogen gas changes the diamond film microstructure from faceted to spherical grains, with signs of GaN etching. The sp3 bonded diamond film produced by nitrogen addition was found to be co-deposited along with a considerable amount of other non-diamond carbon phases (D - disordered graphite, G - crystalline graphite, TPA - trans-polyacetylene) and qualitatively all the diamond films were 50% pure (Raman peak ratio Isp3 / ID). The FWHM of the sp3 carbon Raman peak was calculated to be 6.5 cm-1, when there was no nitrogen gas in the precursor recipe, which deteriorates to a large extent after successive addition of N2. Fourier transform infrared spectroscopy (FTIR) showed a strong presence of the nitrogen related defects (peak positions at 1190 and 1299 cm-1) inside the nanocrystalline diamond (NCD) films grown with N2 addition. GaN layer etching from the base substrate by the CVD plasma was clearly evidenced by energy dispersive X-ray spectra (EDS) of the deposited films. Al elemental EDS peaks from the base sapphire substrate were observed for the films grown with nitrogen addition, but no Ga EDS peaks were detected. X-ray diffraction (XRD) micrographs further supported the enhanced GaN etching phenomenon. Nitrogen addition was thus found to be detrimental for growing CVD diamond films over GaN surfaces. The electrical resistivity of the uncoated GaN was initially measured to be 22.2 Ω-cm. However, the resistivity rose to 1.59×106 Ω-cm after the nitrogen assisted film deposition; due to the GaN etching - thereby exposing the underlying insulating sapphire substrate.

Detection of subsurface archaeological remains using a range of remote sensing methods, poses several challenges until today. Recent studies regarding the detection of archaeological proxies like those of cropmarks highlight the complexity of the phenomenon. In this work we present three different methods, and associated indices, for identifying stressed reflectance signatures indicating buried archaeological remains, based on a dataset of measured ground spectroradiometric reflectance. Several spectral profiles between the visible and near infrared part of the spectrum, were taken over a controlled environment in Cyprus during the 2011-2012 and are re-used in this study. The first two (spectral) methods are based on a suitable analysis of the spectral signatures in (1) the visible part of the spectrum, and in particular in the neighborhood of 570 nm, and (2) the red edge-near infrared part of the spectrum, in the neighborhood of 730 nm. Machine learning (decision trees) allows for the deduction of suitable wavelengths to focus on, in order to formulate the proposed indices and the associated classification criteria (decision boundaries) that can enhance the detection probability of stressed vegetation. Noise in the signal is taken into account by simulating reflectance signatures perturbed by white noise. Applying decision tree classification on the ensemble of simulations and basic statistical analysis we refine the formulation of the indices and criteria for the noisy signatures. The success rate of the proposed methods is over 90%. The third method rests on the estimation of vegetation/canopy reflectance parameters through inversion of the physical-based PROSAIL reflectance model and the associated classification through machine learning methods. The obtained results provide further insights into the formation of stress vegetation that occurred due to the presence of shallow buried archaeological remains, which are well aligned with physical-based models and existing empirical knowledge. To the best of the authors' knowledge, this is the first study demonstrating the usefulness of radiative transfer models such as PROSAIL for understanding the formation of cropmarks. Similar studies can support future research directions towards the development of regional remote sensing methods and algorithms if systematic observations are adequately dispersed in space and time.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

This paper presents a review on numerical and experimental methods to predict fracture of ad-vanced high strength steels (AHSS). AHSS are widely processed through sheet metal forming processes. Although being an excellent choice when lightweight, high strength and ductility are critical factors, their multi-phase microstructure accentuates forming challenges. To accurately model forming behavior, necking based failure criteria as well as direct fracture models require improvements. As a necking based failure model, the conventional forming limit diagram/curve (FLD/FLC) presents limitations such as in estimating direct fracture (surface cracks, edge cracks, shear cracks), as well as deformation histories under nonlinear strain paths. Thus, significant re-search efforts are being made towards the needs of advanced fracture constitutive models capa-ble of predicting fracture scenarios without necking, more frequently observed in the realm of AHSS. Scientific community research is divided into several directions aiming at improving the forming and fracture behavior accuracy of parts subjected to sheet metal forming operations. In this review paper, a comprehensive overview on ductile fracture modeling is presented. Firstly, the FLD/FLC limitations modeling fracture behavior in sheet metal forming operations are stud-ied. Followed by the recent trends in constitutive material modeling. Afterwards, material char-acterization methods advancements to cover a broad range of stress states are comprised. Final-ly, damage and fracture models predicting failure in AHSS are investigated. This review paper supplies relevant information on the current issues the sheet metal forming community is chal-lenged with due to the trend towards AHSS employment in the automotive industry.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

In this work, two plasmonic structures with two different periodic nanostructures (nanodisk and nanostrip arrays) separated from the gold layer by an ultrathin dielectric Al2O3 layer are proposed, and their optical properties are simulated as 3-dimensional models using COMSOL Multiphysics software tool. The optical responses, such as the amplification of the electric field and the scattering, absorption and extinction cross sections of the two structures, are investigated and compared. The results show that both structures show strong field enhancement in their gap layer, and the structure with the periodic array of metal nanodisks shows stronger field enhancement and larger absorption, extinction, and scattering cross sections in its dipole resonance wavelength, which is defined as a bright plasmonic mode. In addition, some weaker resonant modes are observed for both structures and the reason for their generation is dis-cussed. The analysis of different possible modes in such structures is crucial for their application in various fields.

Dentin bonding is a key in restorative dentistry. Herein, we developed self-etching two-bottle adhesive system containing 10-methacryloyloxidecyl dihydrogen phosphate monomer (MDP) and the physical, mechanical, and biocompatible properties were evaluated. The characteristics of MDP were analyzed using nuclear magnetic resonance (NMR). The water sorption and solubility, the shear-bond strengths to dentin and enamel, and cytotoxicity tests were performed. The newly blended experimental group showed the lowest thickness and water sorption and solubility values. The shear bond strength to enamel and dentin were comparable to control groups (the three other products) all test groups showed 60% of cell viability. In this study, the properties of the newly synthesized adhesive are comparable with the others. The fundamental goal of this study is to get the MDP patent released, as it is intended for domestic production. For this purpose, this dentin adhesive was developed and compared with the commercial product.

In this paper we present magnetoelectric properties of metal/metal-oxide/metal junctions. We use Ti and Fe as metallic layers separated by the porous metal-oxides of iron or titanium formed with the anodization method. This allowed to prepare double junctions with at least one ferromagnetic layer. Here we show magnetoresistance and current-voltage characteristics of the junctions together with their magnetic characteristics. We found positive or negative magnetoresistance depending on junction composition. We discuss also the nature of differential resistance calculated from I-V characteristics. Our findings show that the strongest influence on observed behaviour has a top metallic layer and the interface between this layer and anodized oxide where strong interatomic diffusion is expected.

Effective agricultural management in maize production operations starts with the early quantification of seedlings. Accurately determining plant presence allows growers to optimize planting density, allocate resources, and detect potential growth issues early on. This study presents an in-depth analysis of multiple object detection models used by drones to count maize seedlings, while concurrently investigating the influence of planting density, flight altitude, and plant growth stage. The findings of this study demonstrate that one-stage models are able to more accurately detect maize seedlings than two-stage models. In particular, YOLOv8n exhibits outstanding performance, achieving an F1-score of over 0.92 under various density conditions and maintaining a stable performance, especially under densities below 105,000 plants/ha. Additionally, planting density and growth stage were observed to significantly affect detection accuracy, with performance declining as density and growth stage increased. Image resolution and detection were impacted by flight altitude, with lower flights producing higher-quality results. Ultimately, YOLOv8n displays optimal performance under various conditions, providing crucial data to support intelligent decision-making. This research offers valuable insights into the application of object detection technology and provides a basis for the future development of precision agriculture.

This study was designed for the first time to improve phenolic yield and antioxidant activity of ultrasonic-assisted extraction from Acer truncatum leaves (ATL) using response surface methodology, and phenolic composition in ATL extracted under the optimized condition were characterized by UPLC-QTOF-MS/MS. Solvent and extraction time were selected based on preliminary experiments, and a four-factors-three-levels central composite design was conducted to optimize solvent concentration (X₁), material-to-liquid ratio (X₂), ultrasonic temperature (X₃) and power (X₄) for an optimal total phenol yield (Y₁) and DPPH• antioxidant activity (Y₂). The results showed that the optimal combination was ethanol: water (v:v) 66.21%, material-to-liquid ratio 1:15.31 g/mL, ultrasonic temperature 60 °C, power 267.30 W, and time 30 min with three extractions, giving a maximal total phenol yield of 7593.62 mg gallic acid equivalent /100 g d.w. and a maximal DPPH• antioxidant activity of 74241.61 μmol Trolox equivalent/100 g d.w.. Furthermore, 22 phenolics were first identified in ATL extract obtained under the optimized conditions, indicating that gallates, gallotannins, quercetin, myricetin and chlorogenic acid derivatives were the main phenolic composition in ATL. What’s more, a gallotannins pathway existing in ATL from gallic acid to penta-O-galloyl-glucoside was interpreted. All these results provided practical information aiming at full utilization of phenolics in ATL, together with fundamental knowledge for further research.

Cu₆Sn₅ whiskers precipitated in Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer were found and investigated after reflow soldering and during aging. Ag₃Sn fibers can be observed around Cu₆Sn₅ whiskers in the matrix microstructure, which can play an active effect on the reliability of interconnection. Different morphologies of Cu₆Sn₅ whiskers can be observed, and hexagonal rod structure is the main morphology of Cu₆Sn₅ whiskers. A hollow structure can be observed in hexagonal Cu₆Sn₅ whiskers, and a screw dislocation mechanism was used to represent the Cu₆Sn₅ growth. Based on mechanical property testing and finite element simulation, Cu₆Sn₅ whiskers were regarded as having a negative effect on the durability of Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer.

This investigation mainly focused on the microstructural analysis of Al based hybrid metal matrix composites. Aluminium as base metal and reinforced with 2% B4 C, ZrO2 (2%,4%,6%), SiC (4%,8%,12%). Specimens were manufactured by using conventional stir casting technique. Hybrid metal matrix composites were examined by using Scanning electron microscope. This research explained XRD, EDS and Fractography analysis. This investigation shows the reinforced material has given better results in all aspects than pure Al6061 alloy and homogeneous dispersion of particles inside the matrix. Porosity, delamination, cracks, particle distributions were observed through microstructural analysis. Additionally determined the crystal size of pure Aluminium 6061 alloy and hybrid composites.

Peptides, both natural and synthetic, are well suited for a wide range of purposes and offer versa-tile applications in different fields such as biocatalysts, injectable hydrogels, tumor treatment, and drug delivery. The rising prominence of therapeutic peptides encompasses anticancer, antiviral, antimicrobial, and anti-neurodegenerative properties. The metals Na, K, Mg, Ca, Fe, Mn, Co, Cu, Zn, and Mo are ten of the twenty elements that are considered essential for life. Crucial for under-standing the biological role of metals is the exploration of metal-bound proteins and peptides. Aside from essential metals, there are other, non-essential metals that also interact biologically, exhibiting either therapeutic or toxic effects. Irregularities in metal binding contribute to diseases like Alzheimer’s, neurodegenerative disorders, Wilson's, and Menkes disease. Certain metal com-plexes have potential applications as radiopharmaceuticals. The examination of these complexes was done by preforming UV-Vis, IR, EPR, NMR spectroscopy, and X-ray analysis.

The electrical performance of the back-channel etched Indium–Gallium–Zinc–Oxide (IGZO) thin-film transistors (TFTs) with copper (Cu) source and drain (S/D) which are patterned by a selective etchant was investigated. The Cu S/D were fabricated on molybdenum (Mo) layer to prevent the Cu diffusion to the active layer (IGZO). We deposited the Cu layer using thermal evaporation and performed the selective wet etching of Cu using non-acidic special etchant without damaging the IGZO active layer. We fabricated the IGZO TFTs and compare the performance in terms of linear and saturation region mobility, threshold voltage and ON current (ION). The IGZO TFTs with Mo/Cu S/D exhibits good electrical properties as the linear region mobility is 12.3 cm2/V-s, saturation region mobility is 11 cm2/V-s, threshold voltage is 1.2 V and ION is 3.16 x 10-6 A. We patterned all the layers by photolithography process. Finally, we introduced SiO2-ESL layer to protect the device from the external influence. The results show that the prevention of Cu and introduced ESL layer enhances the electrical properties of IGZO TFTs.

In recent years, unmanned aerial vehicles (UAVs) have become a valuable platform for many applications, including communication networks. UAV-enabled wireless communication faces challenges in complex urban and dynamic environments. UAVs can suffer from power limitations and path losses caused by non-line-of-sight connections, which may hamper better communication performance. To address these issues, reconfigurable intelligent surfaces (RIS) have been proposed as a helpful tool to enhance UAV communication networks. However, due to the high mobility of UAV, complex channel environments, and dynamic RIS configurations, it is challenging to estimate the link quality of ground users. In this paper, we propose a link quality estimation model using a gated recurrent unit (GRU) to assess the link quality of ground users for a multi-user RIS-assisted UAV-enabled wireless communication system. Our proposed framework uses a time series of user channel data and RIS phase shift information to estimate the quality of the link for each ground user. Simulation results showed that the proposed GRU model effectively and accurately estimates the link quality of the ground users in the RIS-assisted UAV-enabled wireless communication network.

Herbal Coffee is getting more popular due to its unique flavor and higher concentration of bioactive compounds, mainly polyphenols. Rosemary is a unique herb with potent antioxidant properties. A green technique called ultrasound aids in releasing bioactive substances from the plant cell wall. In this context, ultrasound-assisted herbal coffee prepared and their anti-diabetic, anti-Alzheimer, and antioxidant activities were measured while the LC/MS was used to determine the bioactive components from the herbal coffee infusion. A total of 95 secondary metabolites were putatively reported, including alkaloids, phenolic acids, and flavonoids, which we identified in the herbal coffee infusion. The total phenolic content (61.5 ± 5.1 mg GAE/g), total flavonoid content (19.3 ± 0.9 mg QE/g), and total condensed tannin (7.6 ± 0.7 mg CE/g) of herbal coffee infusion were observed to be highest of the two remaining samples. The herbal coffee extracts were used to determine all samples' antioxidant, anti-diabetic, and anti-Alzheimer activities. Using LC-MS/MS, we semi-quantified 19 phenolic metabolites. The results show numerous bioactive components in herbal coffee infusion with more potent antioxidant, antidiabetic, and anti-Alzheimer potential. Moreover, more studies must be conducted to confirm how the metabolomic profile of herbal coffee affects its flavor profile.

The bioindicator potential of seagrass ecosystems in coastal trace metal monitoring is low for tropical island ecosystems. This study evaluated the bioindicator potential of six seagrass species exposed to anthropogenic trace metal pollution in the Andaman and Nicobar Islands (ANI) of India. Sediment and seagrass biomass, samples were analyzed for trace metals (Co, Cr, Cu, Fe, Mg, Mn, Ni, Pb, Zn) from four locations of ANI exposed to anthropogenic contamination. Geo accumulation Index values indicated moderate trace metal contamination in seagrass sediment. Seagrass trace metal accumulation from sediment was both species-specific and location- specific for ANI. Small seagrass species such as H. ovalis, H. beccarii and H. uninervis accumulated the maximum concentration of six trace metals (Cr, Cu, Fe, Ni, Pb, Zn) in their tissues compared to big seagrass species like T. hemprichii and E. acoroides of ANI. This study indicates leaves of small seagrass and roots of big seagrass species can serve as short- and long-term bioindicators respectively, of coastal trace metal contamination in tropical islands of ANI.

Drosophila melanogaster serves as a important research model both for genetic investigations and for the study of metal toxicity, facilitating the elucidation of physiological mechanisms comparable to those of human organisms. In our research, we evaluated the toxicity effect resulting from exposure to various concentrations of lead and copper on the prolificity rates throughout the life cycle (egg-adult) of four genotypes of Drosophila melanogaster: wild-type (control), white, brown, and white-vestigial. During our study, the prolificity rates were examined across three repetitions under the impact of exposure to concentrations of 0.50, 1.00, 2.00, and 4.00 mM of copper (CuSO₄) and lead (Pb(C₂H₃O₂₎₂). Prolificity rates throughout the life cycle exhibited variations as a direct consequence of genetic factors, the concentration of exposure, and the specific type of metal, either copper or lead. The mutant white-vestigial genotype revealed an IC₅₀ concentration for prolificity inhibition at lower doses of 2.00 mM for copper and 4.00 mM for lead, in contrast to the control genotype (wild-type), which exhibited an inhibition concentration rate >IC₅₀ of 4.00 mM only in the case of copper. Our results concluded that the (i) dose influences the prolificity rate in a directly proportional manner, (ii) comparative analyses between copper and lead revealed that copper displayed toxicity across all genotypes within the concentration range of 0.50 mM to 2.00 mM. In contrast, lead exhibited toxicity within the concentration range of 1.00 mM to 4.00 mM, highlighting a (iii) more acute toxicity characteristic in the case of copper. Thus, the results of this research reflect the importance of using Drosophila melanogaster as a genetic model in the comparative study of the interaction between genetic factors and the toxicity of metals, offering significant insights into monitoring their impact and defining the maximum permissible doses on organisms.

This article presents a combined route and path planning strategy to guide Skid-Steer Mobile Robots (SSMRs) in scheduled harvest tasks within expansive crop rows with complex terrain conditions. The proposed strategy integrates: i) a global planning algorithm based on the Traveling Salesman Problem under the Capacitated Vehicle Routing approach and Optimization Routing (OR-tools from Google) to prioritize harvesting positions by minimum path length, unexplored harvest points, and vehicle payload capacity, and ii) a local planning strategy using Informed Rapidly-exploring Random Tree (IRRT*) to coordinate scheduled harvesting points while avoiding low-traction terrain obstacles. The global approach generates an ordered queue of harvesting locations, maximizing the crop yield in a workspace map. In the second stage, the IRRT* planner avoids potential obstacles, including farm layout and slippery terrain. The path planning scheme incorporates a traversability model and a motion model of SSMRs to meet kinematic constraints. Experimental results in a generic fruit orchard demonstrated the effectiveness of the proposed strategy. In particular, the IRRT* algorithm outperformed RRT and RRT* with 96.1% and 97.6% smoother paths, respectively. The IRRT* also showed improved navigation efficiency, avoiding obstacles and slippage zones, making it suitable for precision agriculture.

Responding to changing value creation processes in the sheet metal working sec-tor, where the complexity and interchangeability of products challenge traditional dif-ferentiation strategies, this empirical analysis explores integrating service-oriented and data-driven business models as new paths to ensure competitiveness, especially for small and medium-sized enterprises (SMEs). This study aims to capture the current state and challenges associated with the implementation of these business models in this sector. The research was conducted through semi-structured interviews with SMEs in the industry. The findings indicate that service-oriented and data-driven business models are not yet widely adopted and that manufacturing companies re-quire support in their implementation. Fields of action were identified for the industry. These are "Creating awareness and understanding", "Recognizing added value", "In-creasing company maturity" and "Understanding the change process". Cooperation between science and industry is essential in tackling these fields of action to ensure the successful integration of such business models in manufacturing companies. This pa-per identifies challenges in the fields of action that companies must address through a structured approach promoting awareness, recognizing value, improving organiza-tional maturity, and understanding the change process to successfully implement ser-vice-oriented and data-driven business models.

Green synthesis offers a superior alternative to traditional methods for producing metal and metal oxide nanoparticles. This approach is not only benign and safe but also cost-effective, scalable, and straightforward, operating under ambient conditions. Notable metals and metal oxide nanoparticles, such as manganese oxides, iron oxides, silver, and gold, have been produced using various bio-reductants derived from plant extracts. These biological agents not only expedite the reduction process but also stabilize the nanoparticles, serving dual roles as reducing and capping agents. This review presents the green synthesis of nanoparticles (NPs) obtained from biogenic wastes and plant extracts. The green-synthesized nanostructured MnO2 are evaluated as a potential photocatalyst for water treatment and as an electrode material in lithium-ion batteries and supercapacitors. The green-derived iron oxide nanoparticles are examined as promising antioxidant, anti-inflammatory, and anti-diabetic agents. Additionally, this review discusses the green synthesis of precious metal nanoparticles, specifically silver (Ag NPs) and gold (Au NPs), highlighting their potential medical applications in areas like antiviral treatments and cancer therapy.

The production of instant green tea requires hot-water extraction, which is time consuming and contributes to losses in aromatic compounds. In this study, an ultrasonic-assisted technology was used to improve the extraction efficiency of green tea, thereby shortening extraction time from 45 to 15 min. In pure water, the dissolution of caffeine and theanine did not change significantly, but total catechin dissolution increased by 0.23 mg/mL and total tea polyphenol dissolution decreased by 3.2 mg/mL. In 76.2% ethanol, the dissolution of caffeine and theanine did not change significantly, but total catechin dissolution increased by 1.57mg/mL and total tea polyphenol dissolution decreased by 1.5 mg/mL. Additionally, we used microwave-assisted technology to further improve the extraction efficiency of green tea, which shortened the extraction time to 2 min. However, the extraction rate remained unchanged. In pure water, the dissolution of caffeine and theanine did not change significantly, but the dissolution of total catechins increased by 0.41 mg/mL and the dissolution of tea polyphenols decreased by 2.9 mg/mL. Ultrasonic treatment increased the proportion of 3-hydroxybutan-2-one, (5S)-5-(hydroxymethyl)oxolan-2-one and 2-phenylethanol, which were the main aroma compounds in tea. Microwave treatment changed the aroma compounds in tea, causing losses in aroma compounds with low boiling point and maintaining (5S)-5-(hydroxymethyl)oxolan-2-one. The taste and aroma of instant green tea improved based on sensory evaluation results.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

Electromobility promises to efficiently mitigate consequences of increasing traffic volume and its accompanied greenhouse gas emissions. On an individual level, electrified bikes allow emission free electrified mobility at moderate costs and consequently their stock has increased significantly in recent years. This simultaneously increases the demand for spare parts, which are often manufacturer or application-specific, and due to many variants, challenging to provide for the market. This article evaluates powder-based and extrusion-based metal additive manufacturing of a typical electrified bike component to demonstrate an alternative spare parts supply. The investigation demonstrates how these parts can be additively manufactured function equivalent and with sufficient mechanical properties, also taking economical aspects into account. Furthermore, the needed resources and related environmental consequences for metal-based additive manufacturing spare-part production are compared for both process routes. The results show that both routes are capable of producing spare-parts at comparatively same mechanical performance and resource costs, while needed resources such as energy, gases and manufacturing time are significantly lower for powder-based, respectively machine costs for extrusion-based additive manufacturing. Therefore, additive manufacturing offers a promising opportunity to produce parts in small quantities resource efficient and rapidly.

Metal additive manufacturing (AM) has gained much attentions in recent years due to its advantages including geometric freedom and design complexity, appropriate to a wide range of potential industrial applications. However, conventional metal AM methods have high-cost barriers due to the initial cost of the capital equipment, support and maintenance, etc. This study presents a unique low-cost metal material extrusion (MME) technology. The filaments used have polylactic acid (PLA) as the matrix and metal powders (copper, bronze, stainless steel, high carbon iron, and aluminum) as reinforcements. Using the proposed fabrication technology, test specimens were built by extruding polymer/metal composite filaments, which were then sintered in an open-air furnace to produce solid metallic parts. In this research, the mechanical and thermal properties of the built parts are examined using tensile tests, thermogravimetric-, thermomechanical- and microstructural analysis.

Software analysis, debugging, and reverse engineering have a crucial impact in today’s software industry. Efficient and stealthy debuggers are especially relevant for malware analysis. However, existing debugging platforms fail to address a transparent, effective, and high-performance low-level debugger due to their detectable fingerprints, complexity, and implementation restrictions. In this paper, we present HyperDbg, a new hypervisor-assisted debugger for high-performance and stealthy debugging of user and kernel applications. To accomplish this, HyperDbg relies on state-of-the-art hardware features available in today’s CPUs, such as VT-x and extended page tables. In contrast to other widely used existing debuggers, we design HyperDbg using a custom hypervisor, making it independent of OS functionality or API. We propose hardware-based instruction-level emulation and OS-level API hooking via extended page tables to increase the stealthiness. Our results of the dynamic analysis of 10,853 malware samples show that HyperDbg’s stealthiness allows debugging on average 22% and 26% more samples than WinDbg and x64dbg, respectively. Moreover, in contrast to existing debuggers, HyperDbg is not detected by any of the 13 tested packers and protectors. We improve the performance over other debuggers by deploying a VMX-compatible script engine, eliminating unnecessary context switches. Our experiment on three concrete debugging scenarios shows that compared to WinDbg as the only kernel debugger, HyperDbg performs step-in, conditional breaks, and syscall recording, 2.98x, 1319x, and 2018x faster, respectively. We finally show real-world applications, such as a 0-day analysis, structure reconstruction for reverse engineering, software performance analysis, and code-coverage analysis.

The severe volumetric expansion of silicon nanoparticles (~400 %) limits their practical application as an anode material for next-generation lithium–ion battery (LIB). Here, we describe the fabrication and characterization of conformal polydopamine carbon shell encapsulating rattle-type silica@silicon nanoparticles (PDA−PEI@PVP−SiO2@Si) with tunable void structure prepared following a dual SiO2 template using (3–aminopropyl)triethoxysilane (APTES) as a self-catalytic, structure-directing agent to tetraethyl orthosilicate (TEOS) pretreated with polyvinylpyrrolidone (PVP K30) via modified Stöber process. Polyethylene imine (PEI) crosslinking facilitated the construction of interconnected three-dimensional bubble wrap-like carbon matrix structure through hydrothermal treatment, pyrolysis, and subsequent surface-protected etching. The composite anode material delivered 539 mAh·g−1 capacity after 100 cycles at 0.1 A·g−1, and 453 mAh·g−1 rate performance at 5 A·g−1. The satisfactory electrochemical performance of the PDA−PEI@PVP−SiO2@Si was attributed to the following: the rattle-type structure providing void space for Si volume expansion, PVP K30-pretreated APTES/TEOS SiO2 seeds via catalyst-free, hydrothermal-assisted Stöber protecting Si/C spheres upon etching, carbon coating strategy increasing Si conductivity while stabilizing the solid electrolyte interface (SEI), and PEI carbon crosslinks providing continuous conductive pathways across the electrode structure. The present work realizes a promising strategy to synthesize the tunable yolk–shell C@void@Si composite anode materials for high power/energy-density LIB applications.

Levels of trace element pollution in surface soil can be estimated using soil analyses and leaching tests. These methods may reveal different results due to the effect of soil properties, such as grain size and mineral composition, on elemental availability. Therefore, this study advocates an alternative method for monitoring and assessment of trace element pollution in surface soil using terricolous fruticose lichens. Lichens growing at abandoned mine sites and unpolluted areas in southwest Japan and their substrata were analyzed using inductively coupled plasma-mass spectrometry and X-ray fluorescence spectrometry to clarify the relationships between Cu, Zn, As, and Pb concentrations in lichens and soils, including their absorption properties. Concentrations of these elements in the lichens were positively correlated with those in the soils regardless of lichen species, location, habitat, or conditions of soils. The analyzed lichens had neither competitive nor antagonistic properties in their elemental absorption, which made them good biomonitors of trace element pollution in surface soil. The distribution maps of average Cu, Zn, As, and Pb concentrations at each sampling region detected almost all of the Cu, Zn, and As pollution of the soils. Therefore, lichens could be used in practical applications to monitor Cu, Zn, and As pollution in surface soils.

The goal of this research is to determine the optimal microwave-assisted sol-gel synthesis pa-rameters of TiO2 nanoparticles with the achievement of the crystalline TiO2 nanoparticles with the highest specific surface area and the lowest energy band gap. Titanium isopropoxide was used as a precursor to prepare the sol (colloidal solution) of TiO2, isopropanol as a solvent, acetylacetone for complexation, and nitric acid as a catalyst. Four samples of titanium dioxide were synthesized from the prepared colloidal solution in a microwave reactor at a temperature of 150 °C for 30 minutes and at a temperature of 200 °C for 10, 20, and 30 minutes. The phase composition of the prepared samples was determined by X-ray diffraction analysis (XRD) and Fourier-transform infrared spectroscopy (FTIR). Nitrogen adsorption/desorption isotherms were used to determine the spe-cific surface area and pore size distributions by Brunauer-Emmett-Teller (BET) method. The band gap energy values of the TiO2 samples were determined by diffuse reflectance spectroscopy (DRS). CrystallineTiO2 nanoparticles with the highest specific surface area and the lowest energy band gap were obtained for the TiO2 sample synthesized at 200 °C for 10 minutes.

We show the enhancement in the intensity and emission rate of perovskite cesium lead bromide (CsPbBr3) and formamidinium lead bromide (FAPbBr3) nanocrystals in the presence of single and double gold layer cavities, which we refer to as Metal-Emitter (ME) and Metal-Emitter-Metal (MEM) nanostructures. Up to 1.9-fold photoluminescence intensity and up to 5.4-fold emission rate enhancements were obtained for FAPbBr3 nanocrystals confined by double gold layers, which are attributed to plasmonic confinement from the gold layers. The experimentally obtained values are validated by analytical calculations and electromagnetic simulations. Such an effective method of manipulation of the spontaneous emission rate by simple plasmonic nanostructures can be utilized in sensing and detection applications.

Physical layer secret key (SK) generation is known to be an efficient means to achieve high secrecy rate, on the condition that dynamic channel state information (CSI) is provided. For this reason, the secrecy performance is highly degraded in a static environment. The intelligent reflecting surface (IRS) is a promising solution to create dynamic randomness, and thus lead to enhanced secrecy performance regardless of the user environments. This paper proposes an IRS-assisted physical layer SK generation scheme, by efficiently combing phase information of the direct and reflected channel information in a hybrid way. In particular, the initial SKs are obtained by adopting efficient phase quantization method with symmetric bit allocation to complex numbered channel estimates. Simulation results show that the proposed hybrid phase quantization (PQ) can improve the SK generation rate and the key disagreement probability in a static environment.

Study question: What are the current trends of research in Human Assisted Reproduction around the world? Summary answer: USA is the leading country, followed by the UK, China, France and Italy. The largest research area is “laboratory techniques”, although other areas such as “public health”, “quality, ethics and law” and “female factor” are gaining ground worldwide. What is known already: Scientific research, especially in health and medical sciences, aims at addressing specific needs that society (and, especially, patients) perceives as pressing. One of the main challenges for policymakers and research funders alike is therefore to align research priorities to societal needs. We can thus think of research agendas in terms of a demand side (societal needs) and a supply side (research outputs). Research output in Human Assisted Reproduction has expanded in the past years, as indicated by the increasing number of scientific publications in indexed journals in this area. Nevertheless, no map of research related to assisted reproduction has been produced so far, hindering the identification of potential areas of improvement and need. Study design, size, duration: 26,000+ scientific publications (articles, letters, and reviews) on Human Assisted Reproduction produced worldwide between 2005 and 2016 were analyzed. These publications were indexed in PubMed or obtained from reference list of indexed publications included in the analysis.Participants/materials, setting, methods: The corpus of publications was obtained by combining the MeSH terms: “Reproductive techniques”, “Reproductive medicine”, “Reproductive health”, “Fertility”, “Infertility”, and “Germ cells”. Then it was analyzed by means of text mining algorithms (Topic Modeling (TM) based on Latent Dirichlet Allocation (LDA)), in order to obtain the main topics of interest. Finally, these categories were analyzed across world regions and time. Main results and the role of chance: We identified 44 main topics, which were further grouped in 11 macro categories, form larger to smaller: “laboratory techniques”, “male factor”, “quality, ethics and law”, “female factor”, “public health and infectious diseases”, “basic research and genetics”, “pregnancy complications and risks”, “general infertility and ART”, “psychosocial aspects”, “cancer”, and “research methodology”. The USA was the leading country in number of publications, followed by the UK, China, France and Italy. Interestingly, research contents in high income countries is fairly homogeneous across macro-categories, and it is dominated by “laboratory techniques” in Western and Southern Europe, and by “quality, ethics and law” in North America, Australia and New Zealand. In middle income countries we observe that research is mainly performed on “male factor”, and noticeably less on “female factor”. Finally, research on “public health and infectious diseases” predominates in low-income countries. Regarding temporal evolution of research, “laboratory techniques” is the most abundant topic on a yearly basis, and relatively constant over time. However, since production in most of the other categories is increasing, the relative contribution of this research category is actually decreasing. Publication is especially increasing in “public health and infectious diseases” (in all world regions, but especially in low income countries), “quality, ethics and law” (high income countries), and “female factor” (middle income countries). Limitations, reasons for caution: Three main factors might limit the robustness of our work: the textual corpus analyzed is based on abstract and titles, the reproducibility of the stochastic algorithms applied, which may produce slightly differing results at each run, and the interpretation of the topics obtained. Wider implications of the findings: This study should prove beneficial in the design of research strategies and policies that foster the alignment between supply (assisted reproduction research) and demand (society). Study funding/competing interest(s): PTQ-14-06718 of the Spanish MINECO Torres Quevedo programme (FAM).

Utilizing unmanned aerial vehicles (UAVs) to facilitate wireless communication has emerged as a viable and promising strategy aimed at enhancing both current and prospective wireless systems. This approach offers many advantages by establishing line-of-sight connections, optimizing operational efficiency, and enabling flexible deployment capabilities in various terrains. Thus, in this paper, we investigate UAV communication in a relaying network in which a UAV helps communication between a source and two destination users while flying to a location. To have a complete view of our proposed system, we consider both orthogonal multiple access as OFDM and non-orthogonal multiple access (NOMA) scenarios. Moreover, we apply successive convex optimization (SCO) and the Block-coordinate gradient descent (BCGD) for the sum-rate optimization problems to improve the system performance under constraints of total bandwidth and total power at the ground base station and UAV. The experimental results validate that the achievable secrecy rates are notably enhanced by using our proposed algorithms and show optimal trends for critical parameters, such as transmit powers, the flight trajectory and speed of UAV, and resource allocation of OFDM and NOMA.

Two-dimensional (2D) transition metal dichalcogenides (TMDCs) nanosheets have shown extensive applications due to their excellent physical and chemical properties. However, the low light absorption efficiency limits their application in optoelectronics. By rolling up 2D TMDCs nanosheets, the one-dimensional (1D) TMDCs nanoscrolls are formed with spiral tubular structure, tunable interlayer spacing and opening ends. Due to their increased thickness of scroll structure, the light absorption is enhanced. Meanwhile, the rapid electron transportation is confined along the 1D structure. Therefore, the TMDCs nanoscrolls show improved optoelectronic performance compared to 2D nanosheets. In addition, the high specific surface area and active edge site from bending strain of basal plane make them promising materials for catalytic reaction. Thus, the TMDCs nanoscrolls have attracted intensive attention in recent years. In this review, the structure of TMDCs nanoscrolls is firstly demonstrated and followed by various preparation methods of the TMDCs nanoscrolls. Afterwards, the applications of TMDCs nanoscrolls in the fields of photodetection, hydrogen evolution reaction, and gas sensing are discussed.

Polymeric particles made up of biodegradable and biocompatible polymers such as poly(lactic-co-glycolic acid) (PLGA) are promising tools for several biomedical applications including drug delivery. Particular emphasis is placed on the size and surface functionality of these systems as they are regarded as the main protagonists in dictating the particle behavior in vitro and in vivo. Current methods of manufacturing polymeric drug carriers offer a wide range of achievable particle sizes, however, they are unlikely to accurately control the size while maintaining the same production method and particle uniformity, as well as final production yield. Microfluidics technology has emerged as an efficient tool to manufacture particles in a highly controllable manner. Here, we report on tuning the size of PLGA particles at diameters ranging from sub-micron to microns using a single microfluidics device, and demonstrate how particle size influences the release characteristics, cellular uptake and in vivo clearance of these particles. Highly controlled production of PLGA particles with ~100 nm, ~200 nm and >1000 nm diameter is achieved through modification of flow and formulation parameters. Efficiency of particle uptake by dendritic cells and myeloid-derived suppressor cells isolated from mice is strongly correlated with particle size and is most efficient for ~100 nm particles. Particles systemically administered to mice mainly accumulate in liver and ~100 nm particles are cleared slower. Our study shows the direct relation between the particle size varied through microfluidics and the pharmacokinetics behavior of particles, which provides a further step towards the establishment of a customizable production process to generate tailor-made nanomedicines.

In this work, we proposed a novel design of microfluidic mixer utilizing the amplified Marangoni chaotic advection induced by AC continuous electrowetting of a metal droplet situated in electrolyte solution, due to the linear and quadratic voltage-dependence of flow velocity at small or large voltages, respectively. Unlike previous researchers exploiting the unidirectional surface stress with DC bias at droplet/medium interface for pumping of electrolyte where the resulting flow rate is linearly proportional to the field intensity, dominance of another kind of dipolar flow pattern caused by local Marangoni stress at the drop surface in sufficiently intense AC electric field is demonstrated by both theoretical analysis and experimental observation, which exhibits a quadratic growth trend as a function of the applied voltage. The dipolar shear stress merely appears at larger voltages and greatly enhances the mixing performance by inducing chaotic advection between the neighboring laminar flow. The mixer design developed herein, on the basis of amplified Marangoni chaotic advection around a liquid metal droplet at larger AC voltages, has great potential for chemical reaction and MEMS actuator applications, because of generating high-throughput and excellent mixing performance at the same time.

Background: Bonsai integrates relaxation, leisure and art therapy into one medium that can have personal, emotional and commercial value and have benefits beyond the therapist’s couch. The art of bonsai, when used as a therapy tool may affect the capacity of the bonsai practitioner to adjust to negative and stressful life events. Objective: The study was initiated to evaluate the benefit of bonsai on the wellbeing of practitioners of the art. Method: 255 bonsai artists participated in a study that examined the effect of bonsai on their well-being. Semi-structured interviews were conducted with bonsai artists. Results: The majority of participants agreed that being able to work on their bonsais affected their moods positively. Discussion: Although bonsai artists did not report better mental health, participants reported an improvement in their mood when working on a bonsai tree. These findings are significant in that it can be especially useful in settings such as psychiatric hospitals, old age homes, orphanages, prisons, etc., as a preventative measure as well as restorative measures in the well-being of patients.

Force reduction is one of the most important benefit of applying ultrasonic vibration on milling. However, most of studies so far are limited to experimental investigation. In the current study, an analytical predictive model on cutting forces in ultrasonic vibration-assisted milling is proposed. The three types of tool-workpiece criteria are considered based on the instantaneous position and velocity of tool center. Type I criterion indicates that there is no contact if the instantaneous velocity is opposite to tool rotation direction. Type II criterion checks whether the vibration displacement is larger than the instantaneous uncut chip thickness. Type III criterion considers the overlaps between current and previous tool paths due to vibration. If none of these criteria is satisfied, milling forces are nonzero. Then the calculation is performed by transforming milling and tool geometry configuration to orthogonal cutting at each instant. The orthogonal cutting forces are predicted through the exhaustive search of shear angle and calculation of shear flow stress on tool-chip interface. The axial force is then calculated based on tool geometry, and the milling forces in feed, cutting, and axial directions are calculated after coordinate transformation. The proposed predictive force model in ultrasonic vibration-assisted milling is validated through comparison to experimental measurements on Aluminum alloy 2A12. The predicted values are able to match the measured milling forces with high accuracy of average difference of 13.6% in feed direction and 13.8% in cutting direction.

Since fine powders tend strongly to adhesion and agglomeration, their processing with conventional methods is difficult or impossible. Typically, in order to enable the handling of fine powders, chemicals are added to increase the flowability and reduce adhesion. This contribution shows that instead of additives also vibrations can be used to increase the flowability, to reduce adhesion and cohesion, and thus to enable or improve processes such as precision dosing, mixing, and transport of very fine powders. The methods for manipulating powder properties are described in detail and prototypes for experimental studies are presented. It is shown that the handling of fine powders can be improved by using low-frequency, high-frequency or a combination of low- and high-frequency vibration.

Metal-supported fuel cells (MSCs) offer potential material cost and robustness advantage over anode supported cells (ASCs). Because of the very good thermal shock stability of such MSCs, these can be heated up very quickly. However the challenge co-firing of metal substrate and electrolyte stays still unsolved. The production of the core component, the tape casted metal substrate, with defined shrinkage resulting from modification of metal powders is presented in the paper. This approach leads to an adjustment of the shrinkage mismatch during sintering, between metal and ceramic components, and adjustment of target specifications like porosity, green density and layer thickness.

In this study, we design a new refractive index sensor based on a metal–insulator–metal waveguide coupled with a notched ring and vertical rectangular resonators. We use the finite element method to study the propagation characteristics of the sensor. According to the calculation results, the transmission spectrum exhibits a typical Fano resonance shape. The phenomenon of Fano resonance is caused by the coupling between the wide spectrum and narrow spectrum. In the design, the wide spectrum signal is generated by the vertical rectangular resonator, while the narrow spectrum signal is generated by the notched ring resonator. In addition, we varied the structural parameters of the resonators and filled the structure with media of different refractive indices to study the sensing properties. The maximum achieved sensitivity of the sensor reached 1071.4 nm/RIU. The results reveal potential applications of the coupled system in the field of sensors.

The indole nucleus is an important element of many natural and synthetic molecules with significant biological activity. Nonetheless, the co-presence of transitional metals in organic scaffold may represent an important factor in the development of effective medicinal agents. This review covers some of the relevant and recent achievements in the biological, chemical and pharmacological activity of important indole-based metal complexes in the area of drug discovery.

Crack inspection is important to monitor the structural health of pavement structures and to facilitate an easier rehabilitation process. Currently, pavement crack inspection is conducted manually, which is inefficient and costly at the same time. For solving the problem, this work has developed a robotic system for automated data collection and analysis in real-time. The robotic system navigates on the pavement and collects visual images from the surface. A deep learning-based semantic segmentation framework named RCDNet was proposed and implemented on the onboard computer of the robot to identify cracks from the visual images. Simulation results show that the deep learning model obtained 96.29% accuracy for predicting the images. The proposed robotic system was tested on both indoor and outdoor environments and was observed that it can complete inspecting a 3m × 2m grid within 10 minutes and a 2.5m × 1m grid within 6 minutes. This outcome shows that the proposed robotic method can drastically reduce the time of manual inspection. Furthermore, a severity map based on the results from visual images was also generated to provide an idea of which locations should be paid more attention to repair in a test grid.

Carbon nanotubes are hybridized with metal crystals to impart multifunctionality into the nanohybrids (NHs). Simple but effective synthesis techniques are desired to form both zero-valent and oxides of different metal species on carbon nanotube surfaces. Sol-gel technique brings in significant advantages and is a viable technique for such synthesis. This study probes the efficacy of sol-gel process and aims to identify underlying mechanisms of crystal formation. Standard electron potential (SEP) is used as a guiding parameter to choose the metal species; i.e., highly negative SEP (e.g., Zn) with oxide crystal tendency, highly positive SEP (e.g., Ag) with zero-valent crystal-tendency, and intermediate range SEP (e.g., Cu) to probe the oxidation tendency in crystal formation are chosen. Transmission electron microscopy and X-ray diffraction are used to evaluate the synthesized NHs. Results indicate that SEP can be a reliable guide for the resulting crystalline phase of a certain metal species, particularly when the magnitude of this parameter is relatively high. However, for intermediate range SEP-metals, mix phase crystals can be expected. For example, Cu will form Cu₂O and zero-valent Cu crystals, unless the synthesis is performed in a reducing environment.

Metal/metal composites represent a particular class of materials showing innovative mechanical and electrical properties. Conventionally, such materials are produced by severely plastically deforming two ductile phases via rolling or extruding, swaging, and wire drawing. This study presents the feasibility of producing metal/metal composites via a capacitive discharge-assisted sintering process named electro-sinter-forging. Two different metal/metal composites with CP-Ti/AlSi10Mg ratios (20/80 and 80/20 %vol) are evaluated, and the effects of the starting compositions on the microstructural and compositional properties of the materials are presented. Bi-phasic metal/metal composites constituted by isolated α-Ti and AlSi10Mg domains with a microhardness of 113 ± 13 HV_0.025 for the Ti20-AlSi and 244 ± 35 HV_0.025 for the Ti80-AlSi are produced. The effect of the applied current is crucial to obtain high theoretical density, but too high currents may result in Ti dissolution in the Ti80-AlSi composite. Massive phase transformations due to the formation of AlTiSi based intermetallic compounds are observed through thermal analysis and confirmed by morphological and compositional observation. Finally, a possible explanation for the mechanisms regulating densification is proposed accounting for current and pressure synergistic effects.

Herein, a novel cavity design of racetrack integrated circular cavity established on metal-insulator-metal (MIM) waveguide is suggested for refractive index sensing application. Over the past few years, we have witnessed several unique cavity designs to improve the sensing performance of the plasmonic sensors created on the MIM waveguide. The optimized cavity design can provide the best sensing performance. In this work, we have numerically analyzed the device design by utilizing the finite element method (FEM). The small variations in the geometric parameter of the device can bring a significant shift in the sensitivity and FOM of the device. The best sensitivity and FOM of the anticipated device are 1400 nm/RIU and ~12.01, respectively. We believe that the sensor design analyzed in this work can be utilized in the on-chip detection of biochemical analytes.

In this paper, we present a novel approach for managing the file system in Linux using a voice assistant. Our system allows users to perform file system operations such as creating directories, renaming files, and deleting files by issuing voice commands. We develop a voice assistant using Python libraries and integrate it with the file system in Linux. The voice assistant is capable of understanding natural language and executing commands based on the user's voice inputs. We conduct experiments to evaluate the performance of the system and demonstrate that our approach is effective and efficient in managing the file system using voice commands. Our system can enhance the accessibility and usability of the file system in Linux for individuals with disabilities or those who prefer a hands-free approach to file management.

People working in the field of Animal-Assisted Interventions (AAI) often state that they perceive animal welfare as a matter of paramount importance, nevertheless most of scientific literature focuses on the effectiveness of interventions from the user's perspective. Before focusing on animals’ management and welfare during the interaction with users, it would be important to ensure animal welfare during their “ordinary lives”. This article reports information and considerations about the management of donkeys involved in AAI in Northern Italy. Six facilities with several years of experience in Donkey-Assisted Interventions were visited for the purpose of an initial data collection regarding the management of donkeys involved in AAI. A general lack of knowledge regarding the nutritional needs of the donkey and a heterogeneity of practices in the field of its preventive medicine have been identified; the study also highlighted a need for efforts to create a more stimulating and enriched environment for animals involved in AAI. Some possible areas for improvement in the management of donkeys involved in AAI have been highlighted. Further studies are necessary to provide a more comprehensive picture of the welfare of donkeys involved in this context.

Isotope detection and identification is paramount in many fields of science and industry, such as in the fusion and fission energy sector, in medicine and material science, and in archeology. The isotopic information provides fundamental insight on the research questions related to these fields as well as insight on product quality and operational safety. However, isotope identification with the established mass-spectrometric methods is laborious and requires laboratory conditions. In this work, Microwave-Assisted Laser-Induced Breakdown Spectroscopy (MW-LIBS) is introduced for isotope detection and identification utilizing radical and molecular emission. The approach is demonstrated with stable B and Cl isotopes in solids and H isotopes in liquid using emission from BO and BO2, CaCl, and OH molecules, respectively. MW-LIBS utilizes the extended emissive plasma lifetime and molecular emission signal integration times up to 900 s to enable use of low ~4 mJ ablation energy without compromising signal intensity and, consequently, sensitivity. On the other hand, long plasma lifetime gives time for molecular formation. Increase in the signal intensity towards the late microwave-assisted plasma was prominent in BO2 and OH emission intensities. As MW-LIBS is online-capable and requires minimal sample preparation, it is an interesting option for isotope detection in various applications.

With the development of Internet technology, teachers are constantly seeking innovative teaching methods to match the potential of enhanced technology. Although many studies have been performed before , they aren’t enough in this field. The purpose of this paper is to explore innovative teaching designs and examine the impact of Internet-assisted English teaching of reading based on constructivism. The case is carried out in NO.9 middle school of Bengbu, a underdeveloped area of China, most of students aren’t interested in learning English .We compared Internet-assisted with traditional textbook literature methods to improve the reading proficiency of students, using a questionnaire survey,pre-test and post-tests comparisons. The result showed Internet-assisted English reading teaching is better than textbook. It can arouse students' interest and motivation,reading proficiency and exam result of students have been improved significantly, created a positive learning situation.

The fuel cell particularly the Proton Exchange Membrane Fuel Cell (PEMFC) is a new energy technology that plays a critical role in achieving market viability. The PEMFC has high power density, zero CO₂ emissions, and high conversion efficiency. However, with uniform distribution of fuel in PEMFC, we can improve the performance and reduce the cost. The PEMFC will be more efficient and effective in terms of renewable energy as a byproduct only water. Metal foam is used as an alternative for the channels in PEMFC. The model of PEMFC was established by using the ANSYS Fluent 3D Model. Then we proposed four configurations of PEMFC. The outcome demonstrates that Case IV provided outstanding performance if it is compared with the other three cases. In terms of power density, Case IV provided a high power density that is double that of Case I. The porosity of metal foam was investigated. The 0.6 porosity value is found as the optimal value. The uniform distribution of the fuel can be achieved at this value which leads to the outstanding current density.

Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.

Background: In the landscape of thoracic surgery, innovation continually drives progress, offering novel approaches to address complex pathologies while prioritizing patient well-being. Dual-portal robotic-assisted thoracic surgery DRATS represents the next frontier in this evolution. In this report we describe our experience with the DRATS approach for segmentectomy with the indocyanine green intersegmental plane identification. Methods: We presented the case of a patient who underwent a DRATS lingulectomy and lymphadenectomy stations 5, 6, 7, and 10 using the daVinci Surgical System. Results: The patient's postoperative course was uneventful with chest tube was removed in second post operative day. The final pathological analysis confirmed a low-grade malignant potential adenocarcinoma, with main diameter of 1.1 cm, at 3 cm from lung margins. 12 nodes were removed, from station 5,6,7,10,11, all of the free of metastases. Conclusions: Our initial observations suggest that Dual-Portal Robotic-Assisted Tho-racic Surgery (DRATS) demonstrates notable feasibility.

Now day; the interest for the synthesis of heterocyclic compounds containing hydroquinoline fragments has increased tremendously due to their wide variety of pharmaceutical and industrial applications. This work details the synthesis of linear and fused heterocyclic systems containing hydroquinoline fragments and the pharmacological activity spectra of the synthesized compounds was predicted by in silico method using Prediction of Activity Spectra of Substances (PASS) program. 1,2,2,4-tetramethyl-1,2-dihydroquinoline-6-carbaldehyde 5a was reacted for three hours with a system of hydroxylammonium chloride/pyridinium chloride/toluene to produce 1,2,2,4-tetramethyl-1,2-dihydroquinoline-6-nitrile 7. N-benzyl-2,2,4-trimethyl-1,2,3,4-tetrahydroquinoline-6-carbaldehyde 6b and iodine reacted at room temperature in aqueous ammonia water, followed by aq. treatment with Na2S2O3 and produced N-benzyl-2,2,4-trimethyl-1,2,3,4-tetrahydroquinoline-6-nitrile 8. 30-60% 2-phenyl-1,3-oxazol-5(4H)-ones 9a,b; 10a,b were synthesized via the condensation reaction of N-alkylhydroquinoline-6-carbaldehydes 5a,b; 6a,b with hippuric acid in acetic acid. When activated 7-methylazolopyrimidines 11a,b were reacted with N-alkyl-2,2,4-trimethyl-1,2,3,4-tetrahydroquinoline-6-carbaldehydes 6a,b, the reaction produced 60–70% yield of 7-[(E)-2,2,4-trimethylhydroquinolin-6-ylidenemethyl]azolo[1,5-a]pyrimidin-6-yl carboxylic acids 12a,b. The condensation reaction of 7-hydroxy-1,2,2,4-tetramethyl-1,2-dihydroquinoline 3h with dimethylacetylenedicarboxylate (DMAD) and ethylacetoacetate afforded methyl (Z)-2-(5,7,7,8-tetramethyl-2-oxo-7,8-dihydrofuro[3,2-g]quinolin-3(2H)-ylidene)acetate 16 and 4,6,8,8,9-pentamethyl-8,9-dihydro-2H-pyrano[3,2-g]quinolin-2-one 17, respectively. The condensation reaction of 6-formyl-7-hydroxy-1,2,2,4-tetramethyl-1,2-dihydroquinoline 5e with methylene active compounds ethylcyanoacetate/dimethyl-3-oxopentanedioate/ ethylacetoacetate/diethylmalonate/Meldrum’s acid afforded 3-substituted dihydroquinoline containg coumarins 19 & 21. A pentacyclic coumarin 22 was obtained via the random condensation reaction of malononitrile with 5e in the presence of catalytic amount of piperidine in ethanol. The potential biological activities of the synthesized compounds were evaluated using PASS computer program. According to the prognosis, (E)-4-(N-alkylhydroquinolin-6-yl)-3-buten-2-ones, 13a, b & 14 showed high probability of being active (Pa) as the Gluconate 2-dehydrogenase inhibitor, Anti-allergic, Anti-asthmatic, and Anti-arthritic with the Pa value of 0.849-0.870. It was also found out that hydroquinolinecarbonitrile compounds 7 & 8 have a propensity to act as a good progesterone antagonists, anti-allergic, anti-asthmatic, and anti-arthritic (Pa = 0.276-0.827). Among the coumarin moieties containing hydroquinolines, compounds 17, 19a, and 19c were predicted to be good progesterone antagonists with the Pa values of 0.710, 0.630 and 0.615; respectively.

Background: Robot-assisted laparoscopic surgery robot-assisted surgical system has gained significant popularity over open and laparoscopic interventions. However, given its high costs, it remains unclear what clinical advantages robot-assisted laparoscopic surgery offers over conventional laparoscopic surgery. Objective: This umbrella review aims to synthesize and compare the clinical outcomes of robot-assisted laparoscopic surgery versus conventional laparoscopic surgery for five surgical procedures. Inclusion criteria: All systematic reviews and meta-analyses published in the past five years that compared the clinical outcomes of conventional laparoscopic surgery and robot-assisted laparoscopic surgery for cholecystectomy, colectomy, hysterectomy, nephrectomy and/or prostatectomy were included. Methods: A systematic literature search was conducted in PubMed and Scopus. The quality of all included reviews was assessed with the AMSTAR 2 quality assessment tool. Each review’s study characteristics (and a list of primary sources) were extracted, along with the quantitative and qualitative data for the following ten clinical outcomes: blood loss, rate of conversion to open surgery, hospitalization costs, incisional hernia rate, intraoperative complication rate, postoperative complication rate, length of hospital stay, operative time, readmission rate and wound infection rate. Results: Fifty-two systematic reviews and (network) meta-analyses were included in this umbrella review, covering more than 1,288,425 patients from 1046 primary sources published between 1996 and 2022. The overall quality of the included reviews was assessed to be low or critically low. Robot-assisted laparoscopic surgery yielded comparable results as conventional laparoscopic surgery in terms of blood loss, conversion to open surgery rate, intraoperative complication rate, postoperative complication rate, readmission rate and wound infection rate for most surgical procedures. While the hospitalization costs of robot-assisted laparoscopic surgery were higher and the operative times of robot-assisted laparoscopic surgery were longer than conventional laparoscopic surgery, robot-assisted laparoscopic surgery reduced the length of hospital stay of patients in nearly all cases. Conclusion: Robot-assisted laparoscopic surgery achieved comparable results with conventional laparoscopic surgery for cholecystectomy, colectomy, hysterectomy, nephrectomy and prostatectomy based on ten clinical outcomes. Further research is needed to prove that robot-assisted laparoscopy is as safe and reliable as conventional laparoscopic surgery.

A pandemic can have a huge impact on normal human life and the economy, taking COVID-19 as an example. While the population flow between countries and regions is the main factor affecting the change of a pandemic, exactly as the airline network. Therefore, realizing the overall control of airports is an effective way to control a pandemic. However, restricted to the differences in prevention and control policies in different areas and privacy issues, the patients’ personal data of the medical center cannot be effectively combined with the passengers’ personal data. This prevents more precise airport control decisions from being made. To the end, this paper designs a novel data sharing framework (i.e., PPChain) based on blockchain and federated learning. The experiment shows that the relationship between the epidemic and aircraft transport can be effectively explored by PPChain, without sharing raw data. This approach does not require centralized trust and improves the security of the shareing process.The scheme can help formulate more scientific and rational prevention and control policies on airports’ control. And it can use aerial data to predict pandemics more accurately.

This article presents new PEM fuel cell models with hexagonal and pentagonal designs. After observing cell performance improvement in these models, we optimized them. Inlet pressure and temperature were used as input parameters, and consumption and output power were the target parameters of the multi-objective optimization algorithm. Then we used artificial intelligence techniques, including deep neural networks and polynomial regression, to model the data. Next, we employed the RSM (Response Surface Method) method to derive the target functions. Furthermore, we applied the NSGA-II multi-objective genetic algorithm to optimize the targets. Compared to the base model (Cubic), the optimized Pentagonal and Hexagonal models averagely increase the output current density by 21.819\% and 39.931\%, respectively.

Cobalt, like other critical elements, is gaining in importance today. The great technological advances and the deep knowledge of the physical and chemical properties of this element have allowed to enhance its applications in various fields, such as: catalysts, paints, alloys for the mechanical and aerospace industries, as well as the medical sector and in recent times, its use within the rechargeable battery industry. The main exploitable deposits are in the Democratic Republic of the Congo, which have economic potential due to a strong influence on their mineralization processes. However, the growing demand for cobalt and the search for less dependence on African deposits leads to targeting other regions, so it is necessary to carry out exhaustive exploration to find out the potential of its reserves for a subsequent benefit of the mineral. Generally, cobalt comes as a by-product of the extraction of other metallic minerals, mainly from Cu-Co, Ni-Co, Ni-Cu-Co deposits. From the above, a first review is carried out on the differences that exist in the geochemical, mineralogical and forecast properties that exist within the different deposits that harbor cobalt. As a second review topic, it delves into efficient processing for cobalt recovery, which is generally carried out by flotation, acid leaching, in addition to its recovery from secondary sources, such as batteries and metallurgical waste. However, generally speaking there is still a vast lack of fundamental knowledge about the processability of cobalt. Said processing has been affected from the point of view of mineralogy, that is, understanding and knowing the cobalt-bearing minerals, as well as gangue mineralogy, these aspects exercise significant control during their processing and selection of the most appropriate route. suitable for cobalt extraction (leaching and/or flotation). In this context, the document concludes with a vision of the challenges that the mining industry must implement to enter circular economy models, mainly in the creation of sustainable processes from secondary sources.

Is there any possible synergic effect of fertility outcome between spindle view-assisted intracyto-plasmic sperm injection (SV-ICSI) with or without assisted oocyte activation (AOA) for patients with low fertilization rate history? To explore the answer, a retrospective study was held in our fertility center by reviewing patients receiving SV-ICSI during 2019/03 to 2023/06. Total 47 pa-tients were included, the fertility outcomes of intervention group (AOA-SV-ICSI, 14 patients) and control group (SV-ICSI, 33 patients), such as fertilization rate, blastocyst formation rate and clin-ical pregnancy rate, were analyzed. The blastocyst formation rate between groups was signifi-cantly higher in AOA-SV-ICSI group (p=0.020), but the fertilization rate and clinical pregnancy rate did not reach any statistical significance. This discovery of increased blastocyst formation rate in low fertilization rate patients could possibly help them in getting more usable embryos in fertility treatment.

Purpose: Early glottic cancer is a highly curable malignancy. Disease control is achieved by resec-tion or external beam radiation with similar long-term results according survival. Surgery is predominantly performed by transoral endoscopic approach, due to reduced complication rates when compared to open cordectomy. Open cordectomy might still be warranted in cases of inad-equate surgical accessibility. Aim of the present study was to compare endoscopic versus open approach in relation to complications and outcome in an up-to-date patient group. Methods: 219 patients underwent primary tumor resection in early glottic cancer (UICC stages I-II). 168 opera-tions were performed endoscopically, 51 operations were open transcervical cordectomies. We compared survival data with non-parametric methods and functional outcome according to need of tracheostomy, feeding tube and voice functional outcome following ELS protocol. Results: There were no significant differences in overall survival (OS). 2 years OS after endoscopic surgery was 90.5% vs 95.3% after transcervical resection. As expected, OS in T1b and T2 tumors was worse than in T1a tumors. We found a statistically significant difference in disease free survival (DFS) within the T1a and T1b/T2 group (Log rank test: p=0.006) but no relevant difference be-tween the two surgical modalities, even when the data was stratified by T-categories performing a Cox regression (hazard ratio 1.21, p=0.712). Patients who underwent open surgery had a sig-nificantly worse peri- and postoperative course with longer hospital stay, higher frequency of tracheotomies and longer need for nasogastric tubes. Functional results were comparable within the two patient groups while higher tumor size / stage was an unfavorable predictor for voice re-habilitation. Conclusion: Open cordectomy leads to more complications but offers comparable oncological and functional outcome when compared to transoral endoscopic approach in early glottic cancer. Open surgery therefore continues to be a valid treatment option when endoscopic resection is not possible.

Keywords: Requirements prioritization, Next release plan, Software product planning, Decision support, MoSCoW, AHP, K-Menas, GMM, BIRCH, PAM, Hierarchical, Clustering, Clusters Evaluation

Driven by the rapidly growing demand for information security, covert wireless communication conceived as one of the essential technology has attracted tremendous attention. However, traditional wireless covert communication is continuously exposing the inherent limitations that challenge deploying in environments with a large number of obstacles, such as cities with high-rise buildings. In this paper, we propose an intelligent reflecting surface (IRS) assisted covert communication system (CCS) with a friendly UAV, where the UAV generates artificial noise (AN) to interfere with the monitors. Furthermore, we model the power of AN emitted by UAV as an uncertainty model, with which the closed-form detection error probability (DEP) on the covert wireless communication for the monitor is derived. Under the derived DEP, we formulate the optimization problem to maximize the covert rate, and an iterative algorithm is designed to solve the optimization problem to obtain the optimal covert rate by using Dinkelbach method. Simulation results show that the proposed system achieves the maximum covert rate when the phase of the IRS units, the trajectory, and the transmit power of the UAV are jointly optimized.

This study investigates the applications of reconfigurable intelligent surfaces (RIS) in heterogeneous downlink networks (HetNet). Due to the network densification, the small cell base station (SBS) interferes with the macrocell users (MUE). In this paper, we utilize RIS to mitigate cross-tier interference in an HetNet via directional beamforming by adjusting the phase shift of the RIS. We consider an RIS-assisted HetNet consisting of multiple SBS nodes and MUEs that utilize both direct paths and reflected paths. Therefore, the aim of this study is to maximize the sum rate of all MUEs by jointly optimizing the transmit beamforming of the macrocell base station (MBS) and the phase shift of the RIS. An efficient RIS reflecting coefficients-based optimization (RCO) is proposed based on a successive convex approximation approach. Simulation results are provided to show the effectiveness of the proposed scheme in terms of its sum rate in comparison with the scheme HetNet without RIS and the scheme HetNet with RIS but with random phase shifts.

With the rapid development of Internet of Vehicles (IoV), particularly the introduction of mobile edge computing (MEC), vehicles can efficiently share data with one another. However, edge computing nodes are vulnerable to various network attacks, posing security risks to data storage and sharing. Moreover, the presence of abnormal vehicles during the sharing process poses significant security threats to the entire network. To address these issues, this paper proposes a novel reputation management scheme, which proposes an improved multi-source multi-weight subjective logic algorithm. This algorithm fuses direct and indirect opinion feedback of nodes through the subjective logic trust model while considering factors such as event validity, familiarity, timeliness, and trajectory similarity. Vehicle reputation values are periodically updated, and abnormal vehicles are identified through reputation thresholds. Finally, blockchain technology is employed to ensure the security of data storage and sharing. By analyzing real vehicle trajectory datasets, the algorithm is proven to effectively improve the differentiation and detection rate of abnormal vehicles.

With the rapid development of the Internet of Things (IoT), there are dramatic increasing number of devices in the network, which causes the challenge that only using infrastructure such as based station cannot provide service with all devices with high quality. Therefore, due to their flexibility and economy, unmanned aerial vehicles (UAV) are widely used to increase the performance of IoT networks. UAVs can not only provide communication services for IoT devices in the absence of a network, but they can also perform video surveillance, cargo transportation, pesticide spraying, and other specialized tasks. However, due to the complexity of the scenario and the need for real-time decision making, it is challenging to schedule UAVs in the network using traditional optimization methods, and growing attention has focused on using AI to optimize UAVs in the network. In this paper, we focus on the AI-enabled UAV optimization method in IoT networks and give a comprehensive scope on what and how to use AI-enabled methods to increase the performance of UAV-assisted IoT networks. Moreover, a brief analysis of the challenges of using AI methods in IoT networks and some potential research directions are given.

This paper proposes a hybrid medium access control (MAC) protocol for wireless sensor network (WSN) data gathering, employing unmanned aerial vehicles (UAV). The UAV sends a beacon frame periodically to inform sensor nodes regarding its presence. Afterward, each sensor node which receives beacon frame contends to send registration frame to the UAV. The UAV will transmit the second beacon frame to the registered nodes to notify their transmission schedule. The time-slot scheme is used for the transmission schedule. The transmission schedule of each sensor is determined based on their priority. Specifically, the priority of each sensor is determined during the registration process. Furthermore, the architecture of UAV-WSN data gathering system is introduced in this paper. Simulations are performed, showing that the proposed MAC protocol achieves fairness while enhancing network performance.

Cochlear implantation (CI) allows rehabilitation for patients with severe to profound hearing impairment. Although the use of a robotic assistant provides technical assistance to the surgeon, the assessment of the impact of its use on auditory outcomes remains uncertain. We aim to com-pare the hearing results of patients who underwent bilateral cochlear implantation, one side was performed with manual insertion and the other side with robot-assisted insertion. The electrode array intrascalar positioning and the surgery duration were also studied. This retrospective intra-individual study involved 10 patients who underwent bilateral cochlear implantation. The study included 2 infants and 8 adults. The unique composition of this cohort enabled us to utilize each patient as their own control. Regarding speech disyllabic recognition, pure tone average, ECAP, ratio of array translocation, basilar membrane rupture, percentage of translocated electrodes there was no difference between manual and robot-assisted CI groups. This study is the first to compare intra-individual hearing performance after cochlear implantation either manually or robot-assisted. The number of patients and the time delay between manual and robotic implantation may have led to a lack of power, but there was no apparent difference in hearing performance between manual and robotic implantation.

Low-dimensional carbon-based (LDC) materials have attracted extensive research attentions in electrocatalysis because of their unique advantages such as structural diversity, low cost, and chemical tolerance. They have been widely used in a broad range of electrochemical reactions to relief environmental pollution and energy crisis. Typical examples include hydrogen evolution reaction (HER), oxygen evolution reaction (OER), oxygen reduction reaction (ORR), carbon dioxide reduction reaction (CO₂RR), and nitrogen reduction reaction (NRR). Traditional “trial and error” strategies seriously slowed down the rational design of electrocatalysts for these important applications. Recent studies show that the combination of density functional theory (DFT) calculations and experimental research is capable of accurately predicting the structures of electrocatalysts, thus could reveal the catalytic mechanisms. Herein, current well-recognized collaboration methods of theory and practice are reviewed. The history of modern DFT, commonly used calculation methods, and basic functionals are briefly summarized. Special attention is paid to descriptors that are widely accepted as a bridge links the structure and activity, and the breakthroughs for high-volume accurate prediction of electrocatalysts. Importantly, correlating multiple descriptors are used to systematically describe the complicated interfacial electrocatalytic processes of LDC catalysts. In addition, machine learning and high-throughput simulations are crucial in assisting the discovery of new multiple descriptors and reaction mechanisms. This review will guide the further development of LDC electrocatalysts for extended applications from the aspect of DFT computations.

The chemical graph theory is a subfield of mathematical chemistry which applies classic graph theory to chemical entities and phenomena. Chemical graphs are main data structures to represent chemical structures in cheminformatics. Computable properties of graphs lay the foundation for (quantitative) structure activity and structure property predictions - a core discipline of cheminformatics. It has a historic relevance for natural sciences, such as chemistry, biochemistry and biology, and is in the heart of modern disciplines, such as cheminformatics and bioinformatics. This review first covers the history of chemical graph theory, then provides an overview of its various techniques and applications for CASE, and finally summarises modern tools using chemical graph theory for CASE.

(1) Background: Although resistance to pathogens and pests has been researched in many potato cultivars and breeding lines with DNA markers, there is scarce evidence as to the efficiency of the marker-assisted selection (MAS) for these traits when applied at the early stages of breeding. A goal of this study was to estimate the potential of affordable DNA markers to track Rpi disease resistance genes, that are effective against the pathogen Phytophthora infestans, as a practical breeding tool on a progeny of 68 clones derived from a cross between the cultivar Sudarynya and 13/11-09. (2) Methods: this population was studied for four years to elucidate the distribution of LB resistance and other agronomical desirable or simple to phenotype traits such as tuber and flower pigmentation, capacity and structure of yield. LB resistance was phenotypically determined through natural and artificial infection and the presence/absence of nine Rpi genes was assessed via 11 sequence-characterized amplified region (SCAR) markers. To aid this analysis, the profile of Rpi genes in the 13/11-09 parent was established using diagnostic resistance gene enrichment sequencing (dRenSeq) as a gold standard. (3) Results: at the early stages of a breeding program, MAS can halve the workload when screening the segregation of F1 offspring and selected SCAR markers for Rpi-genes provide useful tools.

In this paper, a new design of a helium-assisted hybrid drone is proposed for flight time enhancement. As is widely known, most of the drones with a VTOL (vertical take-off and landing) feature have a short operation time, limiting their capability to carry out sustainable operations for the given missions. Thus, with the clear goal of enhancing the flight time, this study aims to develop a hybrid drone system, where a helium balloon is used to provide a lifting force for this purpose. The proposed design for the hybrid drone has several benefits including easiness to manufacture and relatively small size when compared to other types of hybrid drones. Various analyses are conducted for the design of the hybrid drone system including the balloon shape and size, buoyant force, flight time, and connector design. Since stability and performance are one of the most important issues for the new design, the pole location analysis is conducted based on the control theory. This rigorous analysis provides that the proposed hybrid drone design is stable as well as robust against swinging motions. To validate the effectiveness of the proposed design and flight time enhancement, simulations were conducted and experimental results are also provided using the manufactured hybrid drone system. Through the real experiments, it is proved that the hybrid drone can increase the flight time more than 2.5 times while guaranteeing stable motions.

Experimental studies on the development of processes of obtaining ultradispersed metal-ceramic materials and coatings Mo-ZrO₂, Mo-Al₂O₃, W-ZrO₂, W-Al₂O₃ CVD by deposition from the gas phase in CO₂ process using low-temperature nonequilibrium plasma were carried out.The structure, microhardness, phase composition, and high-temperature annealing behavior of the materials were studied. It is shown that the choice of parameters of the deposition process and temperature annealing can be controlled by the distribution function of ultradispersed particles in the material and their sizes.High-temperature X-ray studies of "molecular" two-phase alloys Mo- Al₂O₃ and Mo- ZrO₂show that, depending on the elastic and thermal properties of the matrix materials and dispersed particles, the molybdenum matrix can be in an all-round tensed or all-round compressed state.In the study of the electro-physical characteristics of the two-phase disperse-strengthened alloys Mo- ZrO₂, Mo- Al₂O₃, W- ZrO₂, W- Al₂O₃ it has been established that in the region of temperatures 1023...1273K anomalous changes of specific electrical resistance and instability of thermal eddy in magnitude are observed apparently connected with the presence of internal stresses in material caused by ultradisperse particles.Theoretical aspects of the problem of increasing the carriers density in nanocomposite materials are reviewedTheoretical analysis of the effect of the ensemble of microparticles on the change of electron density in ultradisperse metal-ceramic materials is carried out. It is shown that the average values of the electron density in the matrix with the introduction of 1% of particles with a radius of 50 A increase by more than two orders of magnitude.The possibilities of creating ultradisperse compositions using radiation-plasma methods are considered.

Currently, there are many studies on the application of nanotechnology in therapy. Metallic nanoparticles are promising nanomaterials in cancer therapy, however, functionalization of these nanoparticles with biomolecules has become relevant as their effect on cancer cells is con-siderably increased by photothermal and photodynamic therapy, drug nanocarriers, and speci-ficity by antibodies, resulting in new therapies that are more specific against different types of cancer. This review describes studies on the effect of functionalized palladium, gold, silver and platinum nanoparticles in the treatment of cancer.

This review summarizes experimental and theoretical studies of transition metal complexes with two types of novel metal-carbon bonds. One type features complexes with carbones CL2 as ligands, where the carbon(0) atom has two electron lone pairs which engage in double (σ and π) donation to the metal atom [M] CL2. The second part of this review reports complexes which have a neutral carbon atom C as ligand. Carbido complexes with naked carbon atoms may be considered as endpoint of the series [M]-CR3 → [M]-CR2 → [M]-CR → [M]-C.

A new Pd(II) complex of the previously reported ligand N,N′-bis[(2,2′-dihydroxybiphen-3-yl)methyl]-N,N′-dimethylethylenediamine (L) was obtained from a DMF/H2O mixture. It differs from a Pd(II) complex of L previously obtained by sole DMF. The roles in the solid state assembly of solvent molecules and molecular conformation (driven by specific transition metal ions) were studied by comparing six complexes of L containing different metal centers (Ni(II), Cd(II), Cu(II), Pd(II)). Hirshfeld surface analysis, 2D fingerprint plots and energy frameworks calculations were used to investigate the intermolecular interactions within the crystal packing of the six complexes. As suggested by interaction energies, Pd(II) and Ni(II) complexes arrange to form ribbons, while Cd(II) and Cu(II) complexes form 3D networks. Interactions between complexes and solvent molecules in the previous Pd(II) complex are replaced by complex-complex interactions in the new Pd(II) complex, while BuOH and MeOH are interchangeable in the interactions within the crystal packing of the two Ni(II) complexes. Finally, solvent molecules are not involved in the crystal packing of the Cu(II) complex. The present study suggested that the solid state assembly of these systems is mainly driven by the molecular conformation, that depends in turn by the metal ion involved, while the solvent only plays a minor role.

Metal foams are widely studied as possible tools for the enhancement of heat transfer from hot bodies. The basic idea is that a metal foam tends to increase significantly the heat exchange area between the hot solid body and the external cooling fluid. For this reason, this class of porous materials are considered as good candidates for an alternative to finned surfaces, with different pros and cons. Among the pros, we mention the generally wider area of contact between solid and fluid. Among the cons is the difficulty of producing different specimens with the same inner structure, with the consequence that their performance may be significantly variable. This paper will offer a survey of the literature with a focus on the main heat transfer characteristics of the metal foams. Then, a numerical simulation of the heat transfer at the pore scale level for an artificial foam with a spatially periodic structure will be discussed. Finally, these numerical results will be employed to assess the macroscopic modelling of the flow and heat transfer in a metal foam.

Swarf of aluminum alloy with high corrosion resistance and ductility was successfully converted into fine hydroreactive powders via its ball milling with silver powder and either lithium chloride or gallium. The later substances significantly intensified particle size reduction, while silver formed ‘cathodic’ sites (Ag, Ag2Al) promoting Al corrosion in aqueous saline solutions with hydrogen generation. The diffraction patterns, microphotographs, and elemental analysis results demonstrated partial aluminum oxidation in the samples and their contamination with tungsten carbide from milling balls. Those effects were responsible for obtaining hydrogen yields lower than expected. For AlCl3 solution at 60 °C, Al–LiCl–Ag, Al–LiCl, Al–Ga–Ag, and Al–Ga composites delivered (84.6±0.2), (86.8±1.4), (80.2±0.5), and (76.7±0.7)% of the expected hydrogen respectively. Modification with Ag promoted Al oxidation thus providing higher hydrogen evolution rates. The samples with Ag were tested in CaCl2 solution as well, for which the reaction proceeded much slower. At a higher temperature (80 °C) after 3 h of experiment, the hydrogen yields for Al–LiCl–Ag and Al–Ga–Ag powders were (46.7±2.1) and (31.8±1.9)%. The tested Ag-modified composite powders were considered promising for hydrogen generation and had a potential for further improvement to provide higher performance.

A developing energy-saving approach of cold sintering in a pure aqueous medium was applied to the preparation of α-Al2O3 ceramics and performed on spark plasma sintering equipment. The initial γ-Al(OH)3 and γ-AlOOH powders and the cold-sintered ceramics were studied by X-ray diffraction analysis, infrared spectroscopy, thermal analysis, and scanning electron microscopy to reveal the chemical and structural transformations they experienced during the cold sintering. At 450°C and 70 MPa, initial γ-AlOOH transformed into a fragile α-Al2O3 material. Porous α-Al2O3 ceramics with about 60% porosity was obtained after cold sintering of γ-Al(OH)3 in the same conditions combined with subsequent annealing at 1250°C for 3 h. The role of water molecules in the studied processes was considered as the enhancement of structural mobility in the cold-sintered material due to its reversible hydroxylation similar to earlier investigated supercritical water action on the precursors during α-Al2O3 formation. Further improvement of the cold sintering setup and regimens would open prospects in α-Al2O3 ceramics manufacturing by an ecologically benign route.

In laser-assisted milling, higher temperature in shear zone softens the material potentially resulting in a shift of mean residual stress, which significantly affects the damage tolerance and fatigue performance of product. In order to guide the selection of laser and cutting parameters based on the preferred mean residual stress, inverse analysis is conducted by predicting residual stress based on guessed process parameters, which is defined as the forward problem, and applying iterative gradient search to find process parameters for next iteration, which is defined as the inverse problem. An analytical inverse analysis is therefore proposed for the mean residual stress in laser-assisted milling. The forward problem is solved by analytical prediction of mean residual stress after laser-assisted milling. The residual stress profile is predicted through the calculation of thermal stress, by treating laser beam as heat source, and plastic stress by first assuming pure elastic stress in loading process, then obtaining true stress with kinematic hardening followed by the stress relaxation. The variance-based recursive method is applied to solve inverse problem by updating process parameters to match the measured mean residual stress. Three cutting parameters including depth of cut, feed per tooth, and cutting speed, and two laser parameters including laser-tool distance and laser power, are updated with respected to the minimization of resulting residual stress and measurement in each iteration. Experimental measurements are referred on the laser-assisted milling of Ti-6Al-4V grade 5 and ELI. The percentage difference between experiments and predictions is less than 5% for both materials, and the selection is completed within 50 loops.

Unmanned aerial vehicles (UAVs) have increasingly become integral to multi-access edge computing (MEC) due to their flexibility and cost-effectiveness, especially in the B5G and 6G eras. This paper aims to enhance the Quality of Experience (QoE) in large-scale UAV-MEC networks by minimizing the shrinkage ratio through optimal decision-making in computation mode selection for each user device (UD), UAV flight trajectory, bandwidth allocation, and computing resource allocation at edge servers. However, the interdependencies among UAV trajectory, binary task offloading mode, and computing/network resource allocation across numerous IoT nodes pose significant challenges. To address these challenges, we formulate the shrinkage ratio minimization problem as a mixed-integer nonlinear programming (MINLP) problem and propose a two-tier optimization strategy. To reduce the scale of the optimization problem, we first design a low-complexity UAV partition coverage algorithm based on the Welzl method and determine the UAV flight trajectory by solving a Traveling Salesman Problem (TSP). Subsequently, we develop a coordinate descent (CD) based method and an alternating direction method of multipliers (ADMM) based method for network bandwidth and computing resource allocation in the MEC system. The CD-based method is simple to implement and has a low computational complexity, while the ADMM-based method can further enhance the optimization result through joint optimization. Extensive simulations demonstrate that our proposed algorithms perform well in large-scale edge networks and outperform other representative benchmark methods.

The Semiconductor and Liquid Assisted Photothermal Effect (SLAPE)” concept was employed for the first time in this study to generate electricity from sunlight. In SLAPE process, a semiconducting material is immersed completely in a stable organic solvent to capture the complete sunlight reaching the earth surface and to turn it into the heat-energy that can be eventually converted into electricity by using Organic Rankine Cycle (ORC) with the help of a heat engine and electric generator. In this investigation, the SLAPE solar panels were fabricated with two top and bottom chambers separated by thin thermally conducting metal sheet (Cu or Al). Multi-crystalline silicon photovoltaic cells (SPVCs) in conjunction with -butyrolactone were employed to capture the sunlight, and a low-boiling point dichloromethane (DCM) solvent was employed as a working fluid to capture the in situ generated heat energy from sunlight. Upon exposure to the natural sunlight, the 21 numbers of SPVCs together with about 2 litres -butyrolactone containing one square meter area SLAPE solar panel has generated about 17 V when integrated with a laboratory model reciprocally moved steam engine and a custom-made electric generator, whereas, a commercial SPVC solar panel with 21 number SPVCs generate a maximum voltage of 11 V. The theoretical background governing the SLAPE solar panels, the necessity for their invention and the proof of concept of SLAPE solar panels have been thoroughly presented and discussed and established in this article.