Monitoring volatile organic compounds (VOCs) places a crucial role in environmental pollutants control and indoor air quality. In this study, a metal-oxide (MOx) sensor detector (used in a commercially available monitor) was employed to delineate the composition of air containing three common VOCs (ethanol, acetone and hexane) under various concentrations. Experiments with a single component and double components were conducted to investigate how the solvents interact with the metal oxide sensor. The experimental results revealed that the affinity between VOC and sensor was in the following order: acetone > ethanol > n-hexane. A mathematical model was developed, based on the experimental findings and data analysis, to convert the output resistance value of the sensor into concentration values, which in turn can be used to calculate a VOC-based air quality index. Empirical equations were established based on inferences of vapor composition versus resistance trends, and on an approach of using original and diluted air samples to generate two sets of resistance data per sample. The calibration of numerous model parameters allowed matching simulated curves to measured data. As such, the predictive mathematical model enabled quantifying not only the total concentration of sensed VOCs, but also estimating the VOC composition. This first attempt to obtain semi-quantitative data from a single MOx sensor, despite remaining selectivity challenges, is aimed at expanding the capability of mobile air pollutants monitoring devices.

Sodium borohydride-closo-hydroborate Na3(BH4)(B12H12) exhibits the high room-temperature ionic conductivity and high electrochemical stability. To study the dynamical properties of this mixed-anion compound at the microscopic level, we have measured the 1H, 11B, and 23Na nuclear magnetic resonance spectra and nuclear spin-lattice relaxation rates over the temperature range of 8 – 573 K. Our 1H and 11B spin-lattice relaxation measurements have revealed two types of reorientational jump motion. The faster motional process attributed to reorientations of the [BH4]− anions is characterized by the activation energy of 159 meV, and the corresponding reorientational jump rate reaches ~10^8 s^-1 near 130 K. The slower process ascribed to reorientations of the larger [B12H12]− anions is characterized by the activation energy of 319 meV, and the corresponding reorientational jump rate reaches ~10^8 s^-1 near 240 K. The results of the 23Na nuclear magnetic resonance measurements are consistent with the fast long-range diffusion of Na+ ions in Na3(BH4)(B12H12). The diffusive jump rate of Na+ is found to reach ~10^4 s^-1 at 300 K and ~8 × 10^8 s^-1 at 530 K. Comparison of these jump rates with the ionic conductivity data suggests the importance of correlations between diffusing ions.

In this paper we present magnetoelectric properties of metal/metal-oxide/metal junctions. We use Ti and Fe as metallic layers separated by the porous metal-oxides of iron or titanium formed with the anodization method. This allowed to prepare double junctions with at least one ferromagnetic layer. Here we show magnetoresistance and current-voltage characteristics of the junctions together with their magnetic characteristics. We found positive or negative magnetoresistance depending on junction composition. We discuss also the nature of differential resistance calculated from I-V characteristics. Our findings show that the strongest influence on observed behaviour has a top metallic layer and the interface between this layer and anodized oxide where strong interatomic diffusion is expected.

Green synthesis offers a superior alternative to traditional methods for producing metal and metal oxide nanoparticles. This approach is not only benign and safe but also cost-effective, scalable, and straightforward, operating under ambient conditions. Notable metals and metal oxide nanoparticles, such as manganese oxides, iron oxides, silver, and gold, have been produced using various bio-reductants derived from plant extracts. These biological agents not only expedite the reduction process but also stabilize the nanoparticles, serving dual roles as reducing and capping agents. This review presents the green synthesis of nanoparticles (NPs) obtained from biogenic wastes and plant extracts. The green-synthesized nanostructured MnO2 are evaluated as a potential photocatalyst for water treatment and as an electrode material in lithium-ion batteries and supercapacitors. The green-derived iron oxide nanoparticles are examined as promising antioxidant, anti-inflammatory, and anti-diabetic agents. Additionally, this review discusses the green synthesis of precious metal nanoparticles, specifically silver (Ag NPs) and gold (Au NPs), highlighting their potential medical applications in areas like antiviral treatments and cancer therapy.

The article addresses manufacturing structures made of biodegradable materials that can be successfully used as energy-absorbing liner of sports helmets of all kinds, replacing the previously used expanded polystyrene. The paper is focused on injection technological tests and tensile tests (in quasi-static and dynamic conditions) of several composites based on a PLA matrix with the addition of other biodegradable softening agents, such as PBAT and TPS. Next, the thin-walled elements (dimensions of 55 x 55 x 20 mm) were manufactured and evaluated using a spring-loaded drop hammer. The 60J impact energy was tested according to EN 1078 standard. The dynamic crushing testing included checking the influence of the materials temperature (-20, 0, 20, and 40 °C) and the impact velocity. The PLA15PBAT85 blend was selected as the most effective material in terms of its use as energy-absorbing liner for sport helmets.

The band gap research in graphene is still a very important topic for materials application. Here, we report a band gap opening and p-type semiconducting property of the graphene by using an electrochemical doping on graphene surface. The manganese-oxide nanopar-ticles adsorbed on the graphene were used as the dopants in an electrolyte, which induce the band gap opening and the change of electronic structure. In addition, the fabricated graphene FET shows the p-type semiconductor behaviors. The temperature dependent conductivity of the p-type doped graphene at applied potential of 1.5 V during electro-chemical doping shows the formation of band gap of 0.23 eV, which is obtained from the fitting of conductivity equation. The semiconducting properties of manganese-oxide doped graphene is attributed to the formation of manganese-oxide nanoparticle on the surface of graphene.

Metal-supported fuel cells (MSCs) offer potential material cost and robustness advantage over anode supported cells (ASCs). Because of the very good thermal shock stability of such MSCs, these can be heated up very quickly. However the challenge co-firing of metal substrate and electrolyte stays still unsolved. The production of the core component, the tape casted metal substrate, with defined shrinkage resulting from modification of metal powders is presented in the paper. This approach leads to an adjustment of the shrinkage mismatch during sintering, between metal and ceramic components, and adjustment of target specifications like porosity, green density and layer thickness.

This paper presents and demonstrates the development of a new lightweight coating for aluminium alloy using a novel multicomponent alloy based on the AlSiMgCu system. This coating was applied using a newly designed approach that combined High-Velocity Oxy-Fuel (HVOF) and Plasma Spraying processes. This hybrid technique enables the deposition of coatings with enhanced performance characteristics. The microstructure was studied using optical microscopy (OM) and scanning electron with energy dispersive X-ray spectroscopy (SEM+EDS) microscopy, revealing good adhesion and compaction between the multicomponent coating and the A6061 substrate with 50 to 150 µm thickness. Vickers indentations were performed on the substrate and the new coating material, revealing a 50% improvement in the material's hardness compared to the casted alloy. Additionally, electrical conductivity measurements showed approximative x3.3 times values compared to the alloy in as-cast condition due to high solidification rates altering the morphology of the phases. Corrosion tests demonstrated a lower corrosion rate compared to other multicomponent aluminium alloys and similar to thermal treated A6061 alloy. Finally, tribological results obtained using ball on disc (BOD) test and laser scanning confocal microscopy, confirmed that the new multicomponent coating exhibited reductions in both friction coefficient and wear rate by more than 20% and 50%, respectively. This study demonstrates that using multi-component aluminium coatings could lead to developing of new automotive parts with enhanced properties for corrosion resistance, electrical conductivity, and wear conditions. Optimizing the thermal spraying parameters could further enhance the coating, achieving greater and more homogeneous thicknesses and yielding even higher performance properties.

Volatile organic compounds (VOCs) are among the most abundant air pollutants. Their high concentrations can adversely affect the human body and therefore, early detection of VOCs is of outmost importance. Among the different VOCs, in this review paper, we have focused our attention on the monitoring of acetaldehyde by chemiresistive gas sensors using nanostructured semiconducting metal oxides. These sensors not only can provide a high sensing signal for detection of acetaldehyde, but also high thermal and mechanical stability and low price. This review paper is divided into three major sections. First, we will introduce acetaldehyde as the target gas and the importance of its detection. Then, the fundamentals of chemiresistive gas sensors will be briefly presented and, in the last section, a survey of literature on acetaldehyde gas sensors will be discussed. Acetaldehyde sensors working mechanism, their structures and configurations are reviewed. Finally, the future development outlook and potential applications are discussed, giving a complete panoramic view for researcher working and interested in acetaldehyde detection for different purposes in many fundamentals and applicative fields.

In this study, we design a new refractive index sensor based on a metal–insulator–metal waveguide coupled with a notched ring and vertical rectangular resonators. We use the finite element method to study the propagation characteristics of the sensor. According to the calculation results, the transmission spectrum exhibits a typical Fano resonance shape. The phenomenon of Fano resonance is caused by the coupling between the wide spectrum and narrow spectrum. In the design, the wide spectrum signal is generated by the vertical rectangular resonator, while the narrow spectrum signal is generated by the notched ring resonator. In addition, we varied the structural parameters of the resonators and filled the structure with media of different refractive indices to study the sensing properties. The maximum achieved sensitivity of the sensor reached 1071.4 nm/RIU. The results reveal potential applications of the coupled system in the field of sensors.

Carbon nanotubes are hybridized with metal crystals to impart multifunctionality into the nanohybrids (NHs). Simple but effective synthesis techniques are desired to form both zero-valent and oxides of different metal species on carbon nanotube surfaces. Sol-gel technique brings in significant advantages and is a viable technique for such synthesis. This study probes the efficacy of sol-gel process and aims to identify underlying mechanisms of crystal formation. Standard electron potential (SEP) is used as a guiding parameter to choose the metal species; i.e., highly negative SEP (e.g., Zn) with oxide crystal tendency, highly positive SEP (e.g., Ag) with zero-valent crystal-tendency, and intermediate range SEP (e.g., Cu) to probe the oxidation tendency in crystal formation are chosen. Transmission electron microscopy and X-ray diffraction are used to evaluate the synthesized NHs. Results indicate that SEP can be a reliable guide for the resulting crystalline phase of a certain metal species, particularly when the magnitude of this parameter is relatively high. However, for intermediate range SEP-metals, mix phase crystals can be expected. For example, Cu will form Cu₂O and zero-valent Cu crystals, unless the synthesis is performed in a reducing environment.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of >1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

We report the production of metal oxide (TiFe₂O₄, ZnFe₂O₄) nanoparticles by pulsed laser ablation technique in liquid environment. We used nano second Nd: YAG laser systems working at 532 nm and 1064 nm of wavelength, the energy of the laser beam was kept constant at 80 mJ. Absorbance spectra, surface plasmon resonance, optical band-gap and nanoparticle morphology were investigated using ultraviolet-visible (UV-Vis) spectroscopy, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). Changing the wavelength of the laser for growth, nanoparticles shown shift between the absorbance and surface plasmon resonance peaks in their UV-Vis spectra, this implies that the optical properties of the colloid nanoparticles depends on laser parameters, this was confirmed with the variation of the band gap energy. Furthermore, red shift for the absorbance peak was observed for samples as-growth at 532 nm around the 150 nm as function of time preparation. Whereas, for the samples as-growth at 1064 nm there is no shift in the absorbance spectra, this can be due to agglomeration and formation of larger particles. The characterization results shown appropriate plasmonic photo-catalysts properties of the particles, hence the photo activation of the nanoparticles was examined on antibacterial effect using colonies of Staphylococcus Aureus and Escherichia coli.

Recent developments in the field of room temperature ferromagnetic metal oxide semiconductors (RTFMOS) have shown promising potential for improved photocatalytic performance. This review focuses on the combined study of photocatalytic and ferromagnetic properties at room temperature, with a particular emphasis on metal oxides, such as TiO2, which have emerged as a key area of interest in the domains of magnetism and environmental remediation. Despite extensive research over the years, the precise mechanism behind the interplay of ferromagnetism and photocatalysis in these materials remains incompletely understood. Several critical factors contributing to magnetism have been hinted at, including oxygen vacancies and various metal doping. Numerous reports have demonstrated that these factors play a primary role in room temperature ferromagnetism and photocatalysis in wide-band-gap metal oxides. However, establishing a direct correlation between magnetism, oxygen vacancies, dopant concentration, and photocatalysis has proven challenging. This review aims to provide a comprehensive overview of the recent progress in understanding the magnetism and photocatalytic behaviour of metal oxides. By examining the latest findings, this study sheds light on the potential of RTFMOS as effective photocatalysts, thereby contributing to advancements in environmental remediation and related applications.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

With metal oxide semiconductors being a promising candidate for accurate indoor air quality assessments, multiple drawbacks of the gas sensors prevent their widespread use. Examples include poor selectivity, instability over time, and sensor poisoning. Complex calibration methods and advanced operation modes can solve some of those drawbacks. However, this leads to long calibration times, which are unsuitable for mass production. In recent years, multiple attempts to solve calibration transfer have been made with the help of direct standardization, orthogonal signal correction, and many more methods. Besides those, a new promising approach is transfer learning from deep learning. This article will compare different calibration transfer methods, including direct standardization, piecewise direct standardization, transfer learning for deep learning models, and global model building. The machine learning methods to calibrate the initial models for calibration transfer are feature extraction, selection, and regression (established methods) and a custom convolutional neural network TCOCNN. It is shown that transfer learning can outperform the other calibration transfer methods regarding the root mean squared error, especially if the initial model is built with multiple sensors. It was possible to reduce the number of calibration samples by up to 99.3 % (from 10 days to approximately 2 hours) and still achieve an RMSE for acetone of around 18 ppb (15 ppb with extended individual calibration) if six different sensors were used for building the initial model. Furthermore, it was shown that the other calibration transfer methods (direct standardization and piecewise direct standardization) also work reasonably well for both machine learning approaches, primarily when multiple sensors are used for the initial model.

We report on the development of several different thin-film functional material systems prepared by RF magnetron sputtering at Edith Cowan University nanofabrication labs. We conduct research on the design, prototyping, and practical fabrication of high-performance magneto-optic (MO) materials, oxide based sensor components, and heat regulation coatings for advanced construction and solar windows.

Solid oxide cells are capable of efficiently converting various chemical energy carriers to electricity and vice versa. The urgent challenge nowadays is the faster degradation rate compared with other fuel cell/electrolyzer technologies. To understand the degradation mechanisms, simulation of a solid oxide cell is helpful. Since most previous research developed models using commercial software, such as COMSOL and ANSYS Fluent, a gap for knowledge transfer is being gradually formed between academia and industry due to licensing issues. This paper introduces a multiphysics model, developed by a computational code, openFuelCell2. The code is implemented with an open-source library, OpenFOAM. It accounts for momentum transfer, mass transfer, electrochemical reactions and metal interconnect oxidation. The model can precisely predict I-V curves under different temperatures, fuel humidity and operation modes. Comparison between OpenFOAM and COMSOL simulations shows good agreement. The metal interconnect oxidation is modelled, which can predict the thickness of the oxide scale under different protective coatings. Simulations are conducted by assuming an ultra-thin film resistance on the rib surface. It is revealed that coatings fabricated by atmospheric plasma spraying can efficiently prevent metal interconnect oxidation, with a contribution of only 0.53 \% to the total degradation rate.

Keywords: liquid alloys, microstratification, dispersed particles, spontaneous dispersion, criteria for true (entropic) spontaneous dispersion, mechanisms of quasi-spontaneous dispersion, methods and results for assessing size of dispersed particles.

Cellulose-based carbon (CBC) has been widely concerned with its porous structure, high specific surface area, and is liable to adsorb gas molecules and macromolecular pollutants. However, the application of CBC in gas sensing has been little studied. In this paper, ZnO/CBC heterojunction was formed by means of simple co-precipitation and high temperature carbonization. As a new ammonia sensor, the prepared ZnO/CBC sensor can detect ammonia compared with that of the previous pure ZnO ammonia sensor can not at room temperature. It has great gas sensing response, stability and selectivity to ammonia concentration at 200 ppm. This study provides a new idea for the design and synthesis of biomass carbon-metal oxide composites.

Nanomaterials based on metal oxides (MexOy) are employed as catalysts and/or sorbents in processes undergoing conditions in supercritical water (scH2O), the “green” reaction medium used to obtain energy relevant products. Their properties are greatly affected by the synthesis method used to produce the active MexOy. Moreover, in order to maintain their performance, it is more practical and cost-effective to use supported MexOy nanoparticles. Within this context, the present work deals with the preparation of carbon-supported ZnO and CuO composites by an innovative method based on impregnation under scH2O conditions. Metal oxides were impregnated on a carbon (C) support using a continuous flow tubular reactor. The results show that impregnation in scH2O is a promising approach for the preparation of ZnO/C and CuO/C composite materials. This one-step synthesis method, in a continuous flow, uses neither seed layer nor mineralizer, and it needs substantially lower preparation times than the conventional impregnation methods.

Graphene oxide (GO) is considered as one of the promising adsorbents for the removal of various heavy metal contaminants in aquatic environment, due to its beneficial structural, chemical and electronic properties. Using the density functional theory (DFT) approach, we investigate the reactivity of a model GO nanoparticule (C30H14O15) toward neutral and charged lead (Pb) and cadmium (Cd) atoms. We found the model metal-free GO to have a high chemical reactivity. To study the adsorption of the metal atoms on the GO nanoparticle, we have used a single and doubly-adsorbed neutral (Pb0 and Cd0) and charged (Pb2+, Cd2+) atoms. After identified possible adsorption sites on the GO, we found that a single charged metal ion binds more strongly than a neutral atom of the same type. To determine the possibility of multiple adsorptions of GO nanoparticle, two metal atoms of the same species are co-adsorbed on its surface. Our calculations reveals a site-dependent adsorption energy such that when two atoms of the same specie are adsorbed at sites Si and Sj , the binding energy per atom depends on the whether one of the two atoms is adsorbed firstly on the Si or Sj sites. It is also found that the binding energy per atom for two co-adsorbed atoms of the same specie is less than the binding energy of a singly-adsorbed atom which suggests that atoms may become less likely to be adsorbed on the GO nanoparticle when their concentrations increase. This applies to both neutral and charged atoms. We adduce the origin of this observation to be interplay between metal-metal interaction on the one hand and GO-metal on the other, with the former resulting in a less binding for the charged adsorbed metals in particular, due to repulsive interaction between two positively charged ions. The frontier molecular orbitals analysis and the calculated global reactivity descriptors of the respective GO- metal complexes revealed that all the GO-metal complexes have a smaller HOMO-LUMO gap (HLG) relative to that of pristine metal-free GO nanoparticle. This suggests that although the GO-metal complexes are stable, they are less stable compared to metal-free GO nanoparticles. The negative values of the chemical potentials obtained for all the GO-metal complexes further confirms their stability. Our work calculates parameters that will be crucial to rational design of GO nanoparticles for Pb abd Cd ions contaminants removal, and may find application in water purification for example.

Liquid metal alloy, incorporated with microfluidic manipulation, has become a promising candidate for flexible resistive sensor array (RSA) that can imitate the functions of human skin. One advantage of RSA with shared rows and shared columns is to reduce the number of wires from M × N to M + N (rows: M and columns: N) and hence to greatly lessen the complexity and burden on the electrical system. The associated drawback is the crosstalk effect between adjacent elements during measurement. Although many literatures have reported several methods to resolve this limitation, almost all of them focus only on the high resistance value (≥100 Ω) RSA. There is a lack of detailed experimental data that addresses low resistance RSA with sensing elements below 100 Ω. Here, we aim to fill the gap of this field. We established two common RSA readout systems, i.e. zero potential methods (ZPM) (setting non-scanned-sampling-electrode zero potential (S-NSSE-ZP) and setting non-scanned-sampling-electrode zero potential with amplifier (S-NSSE-ZP-A)) and to compare their performances in low resistance value (≤100 Ω) RSA. For ideal resistor RSA, the measurement results show that S-NSSE-ZP has at least one time higher error than S-NSSE-ZP-A.

Hydrogen sulfide is present in active or extinct volcanic areas (mofettas). The habitable premises in these areas are affected by the presence of hydrogen sulfide, which, even in low concentrations, gives off a bad to unbearable smell. If the living spaces considered are closed enclosures, then a system can be designed to reduce the concentration of hydrogen sulfide. This paper presents a membrane way to reduce the hydrogen sulfide concentration to acceptable limits using a cellulosic derivative-propylene hollow fiber based composite membrane module. The cellulosic derivatives considered were carboxymethyl–cellulose (NaCMC), cellulose acetate (CA), methyl 2–hydroxyethyl–cellulose (MHEC), and 2–hydroxyethyl–cellulose (HEC). In the permeation module, hydrogen sulfide is captured with a solution of cadmium that forms cadmium sulfide, usable as a luminescent substance. The composite membranes were characterized by SEM, EDAX, FTIR, FTIR 2D maps, thermal analysis (TG and DSC) and from the perspective of hydrogen sulfide air removal performance. To determine the process performances, the variables were: the nature of the cellulosic derivative–polypropylene hollow fiber composite membrane, the concentration of hydrogen sulfide in the polluted air, the flow rate of polluted air, and the pH of the cadmium nitrate solution. Pertraction efficiency was maximum for the sodium carboxymethyl–cellulose (NaCMC)-polypropylene hollow fiber membrane, a hydrogen sulfide concentration in the polluted air of 20 ppm, polluted air flow rate of 50 L/min, and a pH of 2 and 4.

We used a metal-organic chemical vapor deposition technique to synthesize a boron-doped reduced graphene oxide (B-rGO) material with various electrical characteristics, dependent on simultaneous reduction and doping procedures. The effect of the doping level on the B bonding in the reduced graphene oxide (rGO) layer controlled by the annealing temperature was investigated using X-ray photoelectron spectroscopy (XPS). The XPS data indicated that the B-rGO layer had a higher B concentration and a considerable number of O-B bonds as a result of the appreciable annealing temperature, which resulted in a decreased work function and Schottky contact between B-rGO and n-type Si. Owing to the higher proportion of B-C and B-C3 bonding in the B-rGO device than that in the rGO/Si device, the lower Schottky barrier height of the B-rGO/n-Si vertical junction photodetector resulted in a higher responsivity. This work suggests a facile method of B doping to alter the electrical properties of graphene materials.

Biomass exploitation is a global trend due to the circular economy and the environmentally friendly spirit. Numerous applications are now based on the use of biomass derived products. Hydrogen sulfide (H2S) is a highly toxic and environmentally hazardous gas, which emitted from various processes. Thus, the efficient removal of this toxic hazardous gas following cost effective processes is an essential requirement. In this study, we present the synthesis and characterization of biomass-derived activated-carbon/zinc-oxide (ZnO@AC) composites from different biomass sources as potential candidates for H2S sorption. The synthesis involved a facile method for activated carbon production via pyrolysis and chemical activation of biomass precursors (spent coffee, Aloe-Vera waste leaves, and corncob). Activated carbon production was followed by the incorporation of zinc oxide nanoparticles into the porous carbon matrix using a simple melt impregnation method. The synthesized ZnO@AC composites were characterized using X-ray diffraction (XRD), infrared spectroscopy (IR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and nitrogen porosimetry. The H2S removal performance of the ZnO@AC composites was evaluated through sorption experiments using a handmade apparatus. Our findings demonstrate that the Aloe-Vera, Spent-coffee, and Corncob derived composites exhibit superior H2S sorption capacity up to 106 mgH2S/gads., 66 mgH2S/gads., and 47 mgH2S/gads. respectively.

In this paper, we present the investigation results of radiation-induced effects in metal-oxide-semiconductor (MOS) doped with moderate amounts of Zinc Oxide (ZnO) as a potential candidate for space-borne application. The samples were fabricated via the sputtering method at a working pressure of 3mTorr and a deposition temperature of 300oC. The ZnO samples were exposed to 1.25-MeV gamma-ray utilizing Co60 source, and their electronic response was measured at ionizing doses ranging from 10 kGy to 300 kGy. A comparative work was performed through finite element method to simulate the electronic response of the PN junction diode due to ionizing radiation. The results indicate that the ideality factor of the MOS diode increases as the ionizing dose increases, rendering it unsuitable for use as a diode. The degradation of the electrical parameters was also simulated, showing the increase in hole concentration. These findings suggest that the ejection of electrons occurred, which agrees with the gamma radiation effects trend. Furthermore, as the intensity of radiation increases, the spatial charge that arises from the separation of hole-electron pairs results in a substantial reduction of the electric field in the central portion of the n-type region. These findings provide insights into the degradation of electrical parameters in MOS devices under gamma radiation and have implications for their use in space-borne applications.

We report a simple and high-performance flexible strain sensor based on liquid metal nanoparticles (LMNPs) on polyimide substrate by laser induced deposition. The LMNPs were prepared by ultrasonic method, and then the femtosecond laser direct writing technology was used to induce the assembly and deposition of the LMNPs to form liquid metal microwires. Laser local sintering enhances the connection between particles, and a wearable strain sensor was fabricated with the high sensitivity as high as 76.18, the good linearity (a correlation coefficient of 0.999) in a wide sensing rage, the fast response/recovery time of 159 ms/120 ms. Attributed to these extraordinary strain sensing performances, the sensor can sense various dynamic strains in real time, monitor both subtle physiological activities and large human motions. It can be adhered to human skin, and well reflect the change of facial expression and realize real-time monitoring of facial expression. And the vocal cord vibration can be detected for speech recognition while the sensor attached to the outside of the throat.

Hybrid materials derived adsorbents have showed a great applicable efficiency in various fields including industrial uses and environmental remediation. Herein, the zinc oxide nanoparticles anchored carbon (ZnO-C) is fabricated and utilized for wastewater treatment by adsorption of Zn(II), Cd(II), Co(II) and Mn(II). The surface and structural characteristics are examined by TEM, SEM, XRD, FTIR, EDS and BET surface area. The Kinetics and equilibrium investigations are applied to optimize the adsorptive removal of Zn(II), Cd(II), Co(II) and Mn(II) onto ZnO-C. Results indicated formation of ZnO-C in crystalline spherical granules with nano-size between 29.3 and 48.8 nm. In addition, the spherical granules are gathered to form clusters. The FTIR indicated that the ZnO-C surface is rich with OH groups and ZnO. The adsorption capacity is reported as 212, 209, 200 and 230 mg/L for Zn(II), Cd(II), Co(II) and Mn(II) respectively. The optimum condition for maximum adsorption were pH between 5 and 6, contact time of 180 min and adsorbent dose of 0.1 g/L. The adsorptive removal data modeling for uptake of Zn(II), Cd(II), Co(II) and Mn(II) onto ZnO-C showed agreement with the assumption of pseudo 2nd order kinetic model and Freundlich isotherm suggesting fast adsorption rate and multilayer mechanism. The achieved adsorption capacity using the prepared ZnO-C is more effective compared to ZnO, carbon, Fe3O4 and Fe3O4-C. Real wastewater samples are applied including valley water, industrial wastewater and rain wastewater and evaluated for applicable uptake of Zn(II), Cd(II), Co(II) and Mn(II) using ZnO-C and Fe3O4-C with high efficiency.

In the article we present the results concerning the impact of structural and chemical properties of zinc oxide in various morphological forms, on its gas-sensitive properties tested in an atmosphere containing a very aggressive gas such as chlorine. Two types of ZnO sensor layers obtained by two different technological methods were used. Their morphology, crystal structure, specific surface area, porosity, surface chemistry and structural defects were characterized, and then compared with gas-sensitive properties in a chlorine-containing atmosphere. To achieve this goal scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and photoluminescence spectroscopy (PL) methods were used. The sensing properties of obtained active layers were tested by temperature stimulated conductance method (TSC). We have noticed that their response in chlorine atmosphere is not determined by the size of the specific surface or porosity. The obtained results showed that the structural defects of ZnO crystals play the most important role in chlorine detection. We demonstrated that the Cl2 adsorption is a concurrent process to oxygen adsorption. Both of them occur on the same active species (oxygen vacancies). They concentration is higher on the side planes of the zinc oxide crystal than the others. Thanks to the conducted studies authors demonstrated that to develop a new gas sensor devices not only changing of active layer chemical composition but also controlling its crystal structure and morphology could be used.

The highly crystalline ZnAl Layered Double Hydroxides (ZnAl-NO3- LDHs) are utilized for the potential transformation into Mixed Metal oxides (MMO) through thermal decomposition and used further for the photodegradation of phenol to assess the influence of calcination on ZnAl LDHs with enhanced photoactivity. The structure, composition, and morphological evolution of ZnAl-LDHs to ZnO-based MMO nanocomposites, which are composed of ZnO and ZnAl2O4, after calcination at different temperatures (400-600 ºC), are all thoroughly examined in this work. The final ZnO and ZnAl2O4 base nanocomposites showed enhanced photocatalytic activity. The findings demonstrated that calcining ZnAl-LDHs from 400 to 600 °C increased the specific surface area and also enhanced the interlayer spacing of d003 while the transformation of LDHs into ZnO/ZnAl2O4 nanocomposite through calcining the ZnAl-LDH precursor at 600 °C showed significant photocatalytic properties, leading to complete mineralization of phenol under UV irradiation.

Oxidation reactions on semiconducting metal oxides (SMOs) surfaces have been extensively worked on in catalysis, fuel cells, and sensors. SMOs engaged powerfully in energy-related applications such as batteries, supercapacitors, solid oxide fuel cells (SOFCs), and chemical gas sensors. The deep understanding of SMO surface and oxygen interactions and defect engineering has become significant because all those mentioned applications are based on the adsorption/absorption and consumption/transportation of adsorbed (physisorbed-chemisorbed) oxygen. More understanding of adsorbed oxygen and oxygen vacancies (〖V_O^•,V〗_O^(••)) is needed, as the former is the vital requirement for sensing chemical reactions, while the latter facilitates the replenishment of adsorbed oxygen ions on the surface. We determined the relation between sensor response (sensitivity) and the amounts of adsorbed oxygen ions (O_(2(ads))^-,O_((ads),)^- O_2(ads)^(2-),O_((ads))^(2-)), water/hydroxide groups (H2O/OH^-), oxygen vacancies (〖V_O^•,V〗_O^(••)), and ordinary lattice oxygen ions (O_lattice^(2-)) as a function of temperature. During hydrogen (H2) testing, the different oxidation states (W6+, W5+, and W4+) of WO3 were quantified and correlated with oxygen vacancy formation (〖V_O^•,V〗_O^(••)). We used a combined application of XPS, UPS, XPEEM-LEEM, and chemical, electrical and sensory analysis for H2 sensing. We established a correlation between the H2 sensing mechanism of WO3, sensor signal magnitude, the amount of adsorbed oxygen ions, and sensor testing temperature. This paper also provides a review of the detection, quantification, and identification of different adsorbed oxygen species. The different surface and bulk-sensitive characterization techniques relevant to analyzing the SMOs-based sensor are tabulated, providing the sensor designer with the chemical, physical, and electronic information extracted from each technique.

Band-gap alignment engineering has now been extensively studied due to its high potential application. Here we demonstrate a simple route to synthesize two metal oxide layers and align them together according to their bandgaps on surface of crystalline silicon (c-Si) solar cells. The metal oxide layers can not only extend absorption spectrum to generate extra carriers but also serve to separate electron-hole pairs more efficiently. As a consequence, the photovoltaic performance of SnO₂/CdO /Si double-layer solar cell (DLSC) is highly improved compared to CdO/Si and SnO₂/Si single-layer solar cells(SLSCs) and SnO₂/CdO/Si double-layer solar cell (DLSC). By the alignment engineering, the SnO₂/CdO/Si DLSC produces a short circuit photocurrent (J_sc) of 38.20 mA/cm², an open circuit photovoltage (V_oc) of 0.575 V and a fill factor (FF) of 68.7%, corresponding to a light to electric power conversion efficiency (η) of 15.09% under AM1.5 illumination. These results suggest that with the use of metal oxide layers by band-gap alignment engineering, new avenues have been opened for developing high-efficiency and cost-effective c-Si solar cells.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

The continuous casting process of helical fiber reinforced metal matrix composites was proposed, and the experimental equipment was designed and manufactured. The relationship model be-tween the process parameters and the helical shape of the fibers in the metal matrix is analyzed by differential geometry. Helical carbon fiber reinforced lead matrix composites were prepared under different conditions. When the melting temperature and cooling intensity were increased, the helical radius of helical carbon fiber in lead matrix was increased. When the fiber rotation speed was increased, the helical radius was decreased, and the helical pitch was de-creased proportionally. The experimental results are consistent with the process model. Carbon fiber rein-forced aluminum composites were prepared. Scanning electron microscopy showed that the infiltration between the aluminum matrix and the carbon fiber was not complete. As the volume fraction of carbon fiber which was added in composites is too small, the mechanical properties of the composites have not been significantly improved.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

The regulation of cell death is a fundamental issue in cell biology and continues to be intensely investigated worldwide. The significance of research in this field persists because understanding the determinants of cell lifespan directly impacts the maintenance of multicellular organism homeostasis and, consequently, is crucial for addressing biomedical challenges associated with various diseases. It is recognized that the initiation of cell death can be prompted by both specific signals (such as cytokines or hormones) and nonspecific stimuli, including radiation, temperature increase, or oxidants. When these factors affect a cell, numerous signaling pathways are triggered in the cell, leading to neutralization of the effects of their negative effects or, in case of irreparable damage, to cell elimination. This removal of damaged cells occurs through apoptosis or programmed cell death, a highly regulated process. Numerous signaling molecules participate in orchestrating the apoptotic process, many of which also govern other essential functions within the organism. Physiological factors capable of triggering the apoptotic program in cells include nitric oxide (NO), which serves as one of the key signaling molecules regulating the functions of the cardiovascular, nervous, and immune systems of the organism. The unique chemical nature of NO, along with its numerous intracellular targets and physiologically active redox forms, raises questions about the specific mechanisms through which NO exerts its damaging effects on cells. Utilizing pharmacological preparations- such as sources (donors) of exogenous nitric oxide- represents an approach to investigating the initiation and execution of the apoptotic program in sensitive target cells. Furthermore, this approach holds promise as a direction for discovering new selective drugs.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Intermediate temperature solid oxide fuel cell (SOFC) operation provides numerous advantages such as high combined heat and power (CHP) efficiency, potentially long-term materials stability, and the use of low-cost materials. However, due to the sluggish kinetics of the oxygen reduction reaction at intermediate temperature, the cathode of SOFC requires an efficient and stable catalyst. Significant progress in the development of cathode materials has been made over recent years. In this article, multiple strategies for improving the performance of cathode materials have been extensively reviewed such as A and B site doping of perovskites, infiltration of catalytic active materials, the use of core-shell composites, etc. Emphasis has been given to intrinsic properties such as thermal expansion compatibility, chemical and thermal stability, and oxygen transport number. Furthermore, to avoid any insulating phase formation at the cathode/electrolyte interface, strategies for interfacial layer modifications have also been extensively reviewed and summarized. Based on major technical challenges, future research directions have been proposed for efficient and stable intermediate temperature solid oxide fuel cell (SOFC) operation.

In order to establish the formation patterns of the Co–Mg oxide system, samples with different Co:Mg ratios and heat treatment temperatures were synthesized and studied. Study of the sam-ples confirmed the phase transition of MgxCo2–xO4 spinels into corresponding solid solutions at 800–900 °C. The similarity of formation patterns for different compositions is shown. The rock-salt oxide in low-temperature samples is an anion-modified paracrystalline phase that forms a “true” solid solution only upon spinel decomposition. TPR profiles of decomposed Co3O4 spinel show surface Co3O4 peaks and a wide peak corresponding to well-crystallized CoO, while par-tial Co3O4 TPR up to 380 °C results in dispersed and amorphous CoO. High-temperature non-stoichiometric samples are poorly reduced, indicating their low oxygen reactivity. Spinel reoxidation after heat treatment to 1100 °C by calcination at 750 °C showed complete regenera-tion for MgCo2O4–Co3O4 samples and its absence in case of an excess of MgO relative to stoi-chiometry. Based on the data obtained, it can be concluded that the processes governing the formation of Co–Mg oxide systems are determined by both Co:Mg ratio and the heat treatment conditions, potentially providing the possibility of fine tuning for specific catalytic processes.

Among the various types of gas sensors, the chemoresistive gas sensors based on metal oxides are considered the most attractive ones due to their simple operation, low costs and miniaturization. Thin films of V2O5 undoped and doped with TiO2 were studied as nitrogen dioxide, methane and hydrogen sensors. The experimental kinetics of the electrical conductivity changes due to introduction and removal of gas on metal oxide gas sensors were successfully explained in terms of the Langmuir adsorption theory.

Cu₆Sn₅ whiskers precipitated in Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer were found and investigated after reflow soldering and during aging. Ag₃Sn fibers can be observed around Cu₆Sn₅ whiskers in the matrix microstructure, which can play an active effect on the reliability of interconnection. Different morphologies of Cu₆Sn₅ whiskers can be observed, and hexagonal rod structure is the main morphology of Cu₆Sn₅ whiskers. A hollow structure can be observed in hexagonal Cu₆Sn₅ whiskers, and a screw dislocation mechanism was used to represent the Cu₆Sn₅ growth. Based on mechanical property testing and finite element simulation, Cu₆Sn₅ whiskers were regarded as having a negative effect on the durability of Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer.

The binary metal oxide mesoporous interfacial layers (bi-MO meso IF layer) templated by a graft copolymer is synthesized between a fluorine-doped tin oxide (FTO) substrate and nanocrystalline TiO2 (nc-TiO2). Amphiphilic graft copolymers, Poly(epichlorohydrin)-graft-poly(styrene), PECH-g-PS, was used as a structure-directing agent, and the fabricated bi-MO meso IF layer exhibits good interconnectivity and high porosity. Even if the amount of ZnO in bi-MO meso IF layer increased, it was confirmed that the morphology and porosity of bi-MO meso IF layer was well maintained. In addtion, bi-MO meso IF layer coated onto FTO substrates show higher transmittance compared with a pristine FTO substrate and dense-TiO2/FTO, due to the reduced surface roughness of FTO. The overall conversion efficiency (η) of a solid state photovoltaic cells, dye-sensitized solar cell (DSSC) fabricated with nc-TiO2 layer/bi-MO meso IF layer TZ1 used as a photoanode reaches 5.0% at 100 mW cm-2, which is higher than that of DSSC with a nc-TiO2 layer/dense-TiO2 layer (4.2%), resulting from enhanced light harvesting, good interconnectivity, and reduced interfacial resistance. The cell efficiency of the device did not change after 15 days, indicating that the bi-MO meso IF layer with solid-state electrolyte has improved electrode/electrolyte interface and electrochemical stability. Additionally, commercial scattering layer/nc-TiO2 layer/bi-MO meso IF layer TZ1 photoanode fabricated solid state photovoltaic cells (DSSC) achieved an overall conversion efficiency (η) of 6.4% at 100 mW cm-2.

The importance of bio robotics has been increasing day by day. Researchers are trying to mimic nature in a more creative way so that, the system can easily adopt the complex nature and its environment. Hence, bio robotic gripper plays a role in physical connection between the environment and bio robotics system. While handling the physical world in biorobots gripper, the complexity occurs in feedback system where sensor plays a vital role. Therefore, human centered gripper sensor has a good impact on bio robotics field. But categorical classification and their selection process is not very systematic. This review paper follows PRISMA methodology to summarize the previous works on bio robotics gripper sensor and its selection process.. This paper discusses challenges in soft robotics systems, and the importance of sensing systems to facilitate critical control mechanisms along with their selection considerations. Furthermore, a classification of soft actuation based on gripper has been introduced. Moreover, some unique characteristics for soft robotics sensor are explored namely compliance, flexibility, multifunctionality, sensor nature, surface properties, and material requirements. In addition, a categorization of sensors for soft robotic gripper in terms of modalities has been established ranging from the tactile and force sensor to slippage sensor. Various tactile sensors ranging from piezoelectric sensing to optical sensing are explored as it has utmost importance in soft gripper to effectively address the increasing requirements for intelligence and automation. Finally, taking everything into consideration, a flow diagram has been suggested for selecting sensors specific to soft robotics applications.

Semisolid casting can provide excellent castings, but the nature of the pore-forming mechanisms has not been properly clarified. In the current communication, it was suggested that hydrogen precipitated during slurry making might have a decisive role in the formation of both gas and shrinkage porosity. Intensive stirring at the end of the slurry making process may act as a degassing step. Without the intense stirring, structures of primary slurry particles form around the hydrogen pores, strongly affecting pore formation and feeding during the intensification stage.

Our environment has been significantly impacted by man-made pollutants, primarily due to industries make substantial use of synthetic chemicals, resulting in significant environmental consequences. In this research investigation, the co-precipitation approach was employed for the synthesis of cellulose-based ferric oxide (Fe₂O₃/cellulose) and copper oxide nanoparticles (CuOx-NPs). Scanning electron microscopy (SEM) analyses were conducted to determine the properties of the newly synthesised nanoparticles. Furthermore, the synthesized nanoparticles were employed for eliminating chromium from aqueous media under various conditions, including temperature, contact time, adsorbent concentration, adsorbate concentration, and pH. Additionally, the synthesised materials were used to recover Cr(VI) ions from real samples, including tap water, seawater, and industrial water, and the adsorptive capacity of both materials evaluated under optimal conditions. The synthesis of Fe₂O₃/cellulose and CuOx-NPs proved to be effective, as indicated by the outcomes of the study.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

In this study, a composite film was developed for electrochemical sensing of tryptophan (Trp). Porous reduced graphene oxide (PrGO) was utilized as the electron transfer layer, and a C-undecylcalix[4] resorcinarene Langmuir-Blodgett (CUCR-LB) film served as the molecular recognition layer. Atomic force microscopy (AFM), transmission electron microscopy (TEM), Raman spectroscopy, scanning electron microscopy (SEM), and electrochemical experiments were employed to analyze the characteristics of the CUCR-LB/PrGO composite film. The electrochemical behavior of Trp on the CUCR-LB/PrGO composite film was investigated, revealing a linear response range of Trp was 1.0×10-7 to 3.0×10-5 mol L-1 and a detection limit of 3.0×10-8 mol L-1. Furthermore, the developed electroanalytical method successfully determined Trp content in an amino acid injection samples. This study not only introduces a rapid and reliable electrochemical method for determination of Trp but also presents a new strategy for constructing high-performance electrochemical sensing platforms.

Heavy metal pollution poses a significant threat to ecosystems and human health worldwide. In response to this pressing issue, bioremediation has emerged as a promising approach for mitigating contamination. This paper adopts a bibliographic method to explore the key techniques and applications of bioremediation. Furthermore, we delve into the most prominent threats to human environmental health and the corresponding remediation methods. Additionally, we discuss the future trajectory of bioremediation research, with a particular focus on the integration of big data and machine learning technologies. These advanced methodologies hold great potential for enhancing the effectiveness and efficiency of environmental remediation efforts in the face of escalating pollution challenges.

In electromagnetic ultrasonic testing, it is difficult to recognize small-size bottom cracks by time of flight (ToF), and the lift-off fluctuation of the probe affects the accuracy and consistency of the inspection results. In order to overcome the difficulty, a novel EMAT (electromagnetic acoustic transducer)-PEC (pulse eddy current) composite sensor is designed. We use amplitude of bottom echo recorded by EMAT to identify the tiny bottom crack as well as the amplitude of PEC signals picked up by the integrated symmetric coils to measure the average lift-off of the probe in real time. Firstly, the effects of lift-off and bottom cracks on amplitude of bottom echo are distinguished combining the theoretical analysis and finite element method (FEM). And then an amplitude correction method based on the fusion of EMAT and PEC signals is proposed to reduce the impact of lift-off on the defect signal. The experimental results demonstrate that the designed composite sensor can effectively detect the bottom crack as small as 0.1mm* 0.3mm. The signal fusion method can accurately correct the amplitude of defect signal and the relative error is less than ±8%.

DFT calculations on the photoisomerization reactions of pyridazine N-oxide derivatives are presented. The irradiation of 3,6-diphenylpyridazine N-oxide allowed to obtain the first excited singlet state that underwent to a ring opening reaction induced to the oxygen migration to the adjacent carbon atom, with the formation of a diazo derivative. This intermediate can give a ring closure reaction to give a pyrazole derivative, or, with a higher transition energy, it can lose nitrogen allowing the formation of 2,5-diphenylfuran. The irradiation of 3-phenylpyridazine N-oxide allowed the formation only of 2-phenylfuran. In this case, calculations allowed to explain this behavior. The first excited singlet state gave a photoisomerization reaction with the formation of the corresponding diazo intermediate. This intermediate could not be converted into the corresponding pyrazole derivative because it was converted into a N-formyl pyrazole never reported in literature. The only possible reaction is the loss of nitrogen and the formation of 2-phenylfuran.

This study investigates the impact of circular economy (CE) strategies on organizational resilience (OR) within the metal industry, focusing on a case study of a forging department in a large man-ufacturing company. The idea of the paper is to link the macroeconomic topic of circular economy (CE) with microeconomic and practical activities in the organization, exploring how CE principles can improve resource efficiency, sustainability, and organizational resilience. A systematic literature review and case study methodology were used to assess the relationship between CE and OR. The findings reveal that companies with higher circularity demonstrate better resilience, both in normal operations and during crises. Specifically, in the case study, the closure of the forging department, following a detailed analysis using the Inputs-Mediators-Outputs (IMO) model, emerged as the most sustainable option, yielding financial, environmental, and operational benefits. This decision aligned with the company’s long-term goals of energy efficiency and carbon neutrality. The research highlights the significance of integrating CE strategies with business processes to not only achieve sustainability but also to build a more adaptable and resilient organization. Future research should explore broader applications of this framework across different industries to strengthen the links between circular economy practices and organizational resilience.

The state of the grinding wheel in the grinding process directly affects the surface quality of the workpiece. The monitoring of the wear state of the grinding wheel can effectively identify the wear information of the grinding wheel and timely and effectively repair the grinding wheel. In this paper, a multi-sensor fusion precision grinding wheel wear intelligent monitoring system is established for typical difficult-to-machine aerospace material titanium alloy, and a multi-eigenvalue fusion algorithm based on improved support vector machine (SVM) is proposed. The extracted sound emission signal wavelet packet decomposition coefficient mean square value, force signal grinding force ratio, and vibration signal effective value are used as the input of the improved support vector machine, and the identification strategy is adjusted by the entropy weight evaluation method. The results show that the monitoring system established in this paper can effectively identify the wear state of the grinding wheel, and the monitoring accuracy can reach more than 92%.

Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with its varied application in solar cells as a transparent front contact, intermediate reflector, back reflector layer and even tunnel layer for passivating contacts, owing to easy tailoring of its optical properties. In this work, we systematically investigate the influence of gas mixture (SiH4, CO2, PH3 and H2), RF power and process pressure on the optical, structural and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material develop-ment using various characterization techniques (SEM, EDX, Raman spectroscopy, and spectro-scopic ellipsometry) with a focus on the relationship between the material properties and the pas-sivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τeff). Further, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8 – 2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with τeff up to 3.5 ms (iVoc ~ 715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films.

Plastic contamination of small dimensions (

This paper investigates an Energy Neutral System using Micro Energy Harvesters for a Health Monitoring Wireless Sensor Node (HM-WSN). We have implemented HM-WSN consisting of a solar cell energy harvester, a Power Management Unit (PMU) and the ucontroller, sensor and transmitter acting as load. A battery extender and a switching logic circuit for sensor node is designed to evaluate the efficiency of the proposed system. The HM-WSN senses body temperature with improvement in lifetime of coincell. The HM-WSN is built using commercially available off the shelf (COTS components and consumes 47.2uW for data being updated every 134s. It can be operated for approximately 1.32 years only on a coincell. Furthermore, the HM-WSN can be operated with solar energy at 200lux, achieving 96.36 years with a combination of a coincell with an additional capacitor of 2.2mF. It attains 4.07 years to 16.87 years lifetime with the load capacitor varying from 1mF to 1.5mF at 350lux lighting condition. With the same ambient condition and a 2mF load capacitor, HM-WSN attains complete energy autonomy.

The impulse of the Fourth Industrial Revolution is triggering the demand for few specific metals. These include copper, silver, gold, and platinum group metals (PGMs), with important applications in renewable energies, green hydrogen, and electronic products. However, the continuous extraction of these metals is leading to a rapid decline in their ore grades and, consequently, increasing the environmental impact of extraction. Hence, obtaining metals from secondary sources, such as waste electrical and electronic equipment (WEEE), becomes imperative for both environmental sustainability and ensuring availability. This recovery entails few problems such as allocation due to the simultaneous production of several metals, the use of non-renewable resources, and the exergy destruction during the life cycle of the metals. Therefore, this work analyses the waste printed circuit boards (PCBs) recycling process by proposing different exergy-based cost allocations for the mentioned metals, disaggregating the exergy cost into non-renewable and renewable, and considering the complete life cycle of metals with the Circular Thermoeconomics methodology. The results show a significant saving of non-renewable energy by using renewable energies in primary extraction (67-87%), recycling (97.6-98.5%), and renewable energies in recycling (98.7%, 99.0%), compared to conventional primary extraction. However, when considering the entire life cycle, between 47% and 53% of the non-renewable exergy is destroyed during recycling. Therefore, delaying recycling as much as possible would be the most desirable option for maximizing the use of non-renewable resources, which nature cannot replace in a short time.

The Internet of Things (IoT) technology connects the real world and the network world by integrating sensors and internet technology, which has greatly changed people's lifestyles, showing its broad application prospects. However, traditional materials for the sensors and power components used in IoT limit its development to high-precision detection, long-term endurance, and multi-scenario applications. Metal halide perovskite, with the unique advantages such as excellent photoelectric properties, adjustable bandgap, flexibility, and mild process, exhibiting enormous potential to meet the requirements for IoT development. This paper provides a comprehensive review of metal halide perovskites' application in sensors and energy supply modules within IoT systems. Advances on perovskite-based sensors were discussed as to gas, humidity, photoelectric, and optical sensors. The application of indoor photovoltaics based on perovskite in IoT systems were also discussed. At last, the application prospects and challenges of perovskite-based devices in IoT are summarized.

A comparative study of the photocatalytic decoloration of methylene blue (MB) dissolved in water was conducted, using three semiconductor oxides: zinc oxide (ZnO), tin oxide (SnO2) and titanium dioxide (TiO2) in the form of thin films and varying their thickness ~ 100, 200, and 300 nm for each film. All the films were deposited using the cost-effective dip-coating technique, at moderate temperature processing (400 °C) with sol-gel solutions on cheap glass substrates. The structural, morphological, and compositional properties of the films were analyzed by X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Raman spectroscopy, respectively. The degradation of MB was studied by varying both thickness and type of semiconductor oxides through measurements of optical absorbance of decolorated liquid by photocatalytic process. Structural analysis shows that ZnO and SnO2 films were polycrystalline with preferential growth of (002) and (110) planes respectively, whereas, an amorphous structure was observed for TiO2 films. In addition, morphological properties confirms that the surfaces of all the films are conformed with nano grains in round and irregular shapes. Based on all results reported in this work, that authors believe that the degradation efficiency of MB depends on the thickness of the film and the type of semiconductor material used as a catalyst. The highest degradation efficiencies were recorded with an exposure time of 120 min and with an initial concentration of 10 mg/L for ZnO, SnO2, and TiO2 films were: 100, 88 %, and 76 %, respectively.

This study provides an in-depth review of the available literature on metal composite material machining, focusing on traditional machining operations such as turning, milling, shaping, drilling, and grinding. The motivation for the study is that this composite type has emerged as a vital material in applications requiring functionality, resilience, cost-effective operation, low consumption of energy and lightweight. Despite its superior characteristics, the manufacturing complexity and poor machinability of metal matrix composites have been the primary barriers to its adoption. Nevertheless, there is a reduction of exceptional efficiency, increase in surface roughness, tool wear and so on in metal matrix composites throughout machining. As a result, this review gives a comprehensive investigation of metal matrix composite machining and effect on process parameters and procedures. Furthermore, this study distinguishes metal matrix composites towards sustainable manufacturing and the metals employed by the researchers, as well as the gaps discovered for future recommendations in metal-based composites.

Magneto-optic (MO) imaging and sensing are at present the most developed practical applications of thin-film MO garnet materials. However, future component and system-level sensors and imagers technology improvements are still necessary in order to improve sensitivity for a range of established and also the forward-looking applications. These improvements are expected to originate from new material system development. We propose a set of technological modifications for the RF-magnetron sputtering deposition and crystallization annealing of magneto-optic bismuth-substituted iron-garnet films and investigate the improved material properties. Results show that standard crystallization annealing for the as-deposited ultrathin (sputtered 10 nm thick, amorphous phase) films resulted in more than a factor of two loss in the magneto-optical activity of the films in visible spectral region, compared to the liquid-phase grown epitaxial films. Results also show that an additional 10 nm-thick metal-oxide (Bi2O3) protective layer above the amorphous film results in ~2.7 times increase in the magneto-optical quality of crystallized iron-garnet films. On the other hand, the effects of post-deposition oxygen (O2) plasma treatment on the magneto-optical (MO) properties of Bismuth substituted iron garnet thin films material is investigated. Results show that, in the visible part of the electromagnetic spectrum (at 532 nm), the O2 treated (up to 3 minutes) garnet films retain higher specific Faraday rotation and figure of merit than those of non-treated garnet films.

Energy generation now heavily relies on the field of photocatalysis. Many conventional research topics have been superseded by the conversion of solar energy into chemical or thermal energy for a variety of energy-related applications. The urgent necessity of moving away from non-renewable energy sources is a result of the problem of global warming. In an effort to create the best photocatalysts for effective solar conversion, scientists are investigating a variety of material systems and material combinations. By examining the influence of morphology changes on the photoelectrochemical activity of zinc oxide nanostructures, here electrodeposition was used to create the nanostructures. By using the proper capping agents, it is possible to control the growth rates of different ZnO facets and get well-defined nanostructures and orientation. In order to generate distinct ZnO morphologies, we report here the electrodeposition of ZnO nanostructured thin films in the presence of different capping agents. A zinc nitrate (Zn (NO₃)₂) bath was used to electrodeposit ZnO nanostructures on indium tin oxide glass (ITO) substrate at 70 °C with an applied potential of -1.0 V. Capping agents such as ethylenediamine (EDA) or ammonium fluoride (NH₄F) were added to this zinc nitrate bath. The photoelectrochemical capabilities of the morphology-controlled zinc oxide nanostructures were extensively evaluated and characterised. Thus various ZnO morphologies had an impact on the PEC properties.

In recent decades, the requirements for implantable medical devices increased, but the risks of implant rejection still exist. These issues are primarily associated with poor osseointegration, leading to biofilm formation on the implant surface. This study focuses on addressing these issues by developing a biomaterial for implant coatings. 45S5 Bioglass has been widely used in tissue engineering due to its ability to form a hydroxyapatite layer, ensuring a strong bond between the hard tissue and the bioglass. In this context, 45S5 bioglasses, modified by the incorporation of different amounts of copper oxide, from 0 to 8 mol%, were synthesized by the melt-quenching technique. The incorporation of Cu ions does not show a significant change in the glass structure. Since the bioglass exhibited the capacity of being polarized, and therefore promoting the osseointegration effectiveness, the electrical properties of the prepared samples were studied using the impedance spectroscopy method, in the frequency range of 102-106 Hz and temperature range of 200-400 K. The effects of CuO on charge transport mobility were investigated. Additionally, the bioactivity of the modified bioglasses was evaluated through immersion tests in simulated body fluid. The results revealed the initiation of a Ca-P-rich layer formation on the surface within 24 h, indicating the potential of the bioglasses to enhance the bone regeneration process.

Chronic Obstructive Pulmonary Disease (COPD) is a disease characterized by local and systemic inflammation independently of the risk factor; during the exacerbations, such inflammation is accentuated and amplified. A practical inflammatory marker and one with an applicable predictive value in the follow-up has been sought. FeNO has shown an excellent performance in that respect within the context of asthma and has also been studied in tobacco-smoke COPD (COPD-TS). In Biomass-smoke COPD (COPD-BS), this, to our knowledge, has not been evaluated. Objective: To measure FeNO levels in patients with COPD-BS and to compare these with those of patients with stable COPD-TS and in healthy controls. Methods: Transversal, observational, descriptive, comparative, and analytical study. A total of 57 patients, including 23 with COPD-BS, 17 with COPD-TS, and 17 healthy control subjects. The measurement of FeNO was carried out on all of these by means of the on-line chemiluminescence technique; the values were expressed in parts per billion (ppb) for their analysis. Results: It was observed that the FeNO values were similar between COPD-BS and COPD-TS and were significantly different between the healthy and stable COPD (both groups). No correlation was found between pulmonary function and symptoms with FeNO in any of the groups. Conclusions: The level of FeNO in stable COPD is found to be increased in a similar manner in COPD-BS and COPD-TS, with a significant difference on comparing it with that of the healthy subjects.

The article presents the results of studies aimed to identify the effect of foliar treatments of winter wheat, sugar beets and soybeans with mineral and bioorganic fertilizers. Their positive effect on increasing the concentration of mineral forms of nitrogen in soil was revealed. The crop types have a greater influence on the size of nitrous oxide emissions: in winter wheat crops - 679 µg/m3, soybeans - 637.2 µg/m3, sugar beets - 576.8 µg/m3. The amounts of nitrous oxide emissions were lower in the variants without the use of phosphorus-potassium fertilizers. The Ruter AA fertilizer showed the greatest efficiency on winter wheat crops - 42.7 c/ha. Soybean grain yield of 44.2 c/ha was also achieved by using Ruter AA, as well as Geo-humate together with phosphorus-potassium fertilizers. On the background of the actual supply of phosphorus and potassium, maximum yield was obtained when using N30 on the leaf - 39.3 c/ha. Foliar feeding ensured a yield of sugar beet root crops of up to 67.1-77.4 c/ha on the backdrop of the application of phosphorus-potassium fertilizers with the advantage of using Amino turbo. The largest yield of sugar beet roots without use of mineral phosphorus and potassium was ensured by N30 treatment of the leaf in the phases of 4-6 and 8 leaves - 63.2 t/ha. Of the organo-mineral fertilizers and biostimulants, the best result was shown by the use of Ruter A - 62.6 t/ha. We believe that foliar feeding of crops can be a sustainable farming method that can increase crop yields and reduce N2O emissions.

A field experiment was conducted for 2 years in Green Tea Laboratory of Saitama Prefectural Agriculture and Forestry Research Center, Iruma, Saitama, Japan from March 2014 to December 2015. Controlled release fertilizers (CRF) or organic fertilizers (ORG) which is the mixture of chicken manure and oil cakewere applied with the amount of 450 kg N ha^-1 yr^-1 in 2014 and 397 kg N ha^-1 yr^-1 in 2015. Nitrous oxide (N₂O) emissionsfrom soil in green tea fields were measured by closed chamber method. The results showed that CRF has significantly lower N₂O compared to ORG. The cumulative N₂O emissions from CRF accounted for 51% of N₂O emissions from ORG fields and 138% of control with no fertilizer treatment. The N₂O flux from the row was higher than that of under the canopy, since fertilizer were applied on the row. However the total emission from the area between the rows was lower than that under the canopy because of the area ratio of row and canopy was 1:5.

In this paper, a seamless connection between sensor technology and machine learning (ML) has been presented which has wide applicability in rehabilitation and physical medicine. The intent is to identify an ML algorithm which has a better performance, easy to deploy, and has less training time and consumes less computational resources. In short, we propose an algorithm which maximizes the synergy between a sensor and ML by maximizing classification performance and easy to do implementation, which is robust in computational power and lower in resource consumption. The premise of the work is to show the important considerations for evaluating ML algorithms for Upper-limb activity recognition for Physical medicine and rehabilitation field.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

Alcoholic liver disease (ALD) develops when the immunotolerant environment of the liver is compromised due to excessive alcohol consumption. ALD progression involves variations in the expression of multiple genes, resulting in liver inflammation and the development of a leaky gut. Molecular mechanism involved for ALD progression is still unclear, and due to that there are currently no FDA-approved drugs available for its treatment. In this study, the protective effects of Graphene oxide nanoparticles (GO) was investigated against ethanol-induced damage in the gut-liver axis in in vitro. GO was synthesized using a modified Hummer's method and characterization was done. Given the general concerns regarding nanoparticle toxicity, assessment of cell viability, lipid accumulation, DNA damage, cell death, and the generation of reactive oxygen species (ROS) were conducted using various techniques. Furthermore, gene expression of pro- and anti-inflammatory cytokines was done using RT-qPCR. The findings revealed that GOs promoted cell viability even against ethanol treatment. Additionally, lipid accumulation significantly decreased when cells were treated with GO alongside ethanol compared to ethanol treatment alone, with similar trends observed for other assays. Gene expression analysis indicated that GO treatment reduced the expression of proinflammatory cytokines while enhancing the expression of antioxidant genes. Moreover, GO treatment led to improvements in gut permeability and a reduction in proinflammatory cytokines in colon cells damaged by ethanol. These findings suggest that GO holds promise as a drug carrier, exhibiting no observed toxic effects. By shedding light on the protective effects of GO against ethanol-induced damage, this study contributes to the burgeoning field of nanoparticle-mediated therapy for ALD.

In this paper, a method is developed for presenting a novel virtual torque sensor based on precise model and position measurements avoids the need of traditional strain gauges and amplifiers. More specifically, the harmonic drive compliance model and the Gaussian process regression (GPR) technique are used together to achieve virtual torque sensor measurement. While the harmonic drive compliance model provides the analytic part, the Gaussian process regression method is used to reconstruct the unmolded part based on motor-side and link-side joint angles as well as motor current. After an automatic offline calibration, the method allows for a lean online implementation. The virtual torque sensor measurement is compared with measurements of a commercial torque sensor, and the results have attested the effectiveness of the proposed method.

Advanced Finite Element (FE) modeling and simulations were performed on vehicular crashes into a Three-bar Metal Bridge Rail (TMBR). The FE models of a sedan, a pickup truck, and a TMBR section were adopted in the crash simulations subject to Manual for Assessing Safety Hardware (MASH) Test Level 2 (TL-2) and Test Level 3 (TL-3) requirements. The test vehicle models were first validated using full-scale physical crash tests conducted on a two-bar metal bridge using a sedan and a pickup truck with similar overall physical properties and sizes to their respective vehicles used in the simulations. The validated vehicular models were then used to evaluate the crash performance of the TMBR using MASH Evaluation Criteria for structural adequacy, occupant risk, and post-impact trajectory. The TMBR met all MASH TL-2 requirements but failed to meet the MASH TL-3 Criteria H and N requirements when impacted by the sedan. The TMBR was also evaluated under in-service conditions (behind a 1.52-m wide sidewalk) and impacted by the sedan under MASH TL-3 conditions. The simulation results showed that the TMBR behind a sidewalk met all safety requirements except for the occupant impact velocity in the longitudinal direction, which exceeded the MASH limit by 3.93%.

The existence of low-cost and accurate tools that can equip the First Responders (FRs) to detect trapped victims and provide insights about their health condition in the aftermath of a disaster, is imperative. To address the problem of detecting trapped victims behind walls or debris, we have developed a tool that exploits an Ultra-Wide Band (UWB) radar sensor for data collection and Machine Learning (ML) algorithms for data analysis. To evaluate the efficacy of our approach, we collected data from nine humans, both in standing and lying down positions. Next, we applied various ML algorithms to the collected dataset for two discrete sub-tasks that are of interest from an FR’s perspective. The first task is the detection of the victim’s presence, where the algorithms attained more than 95% accuracy and F1-Score. The second task is the estimation of the distance between the radar sensor and the victim, where the tool showed an average error of less than 40 cm.

The emerging wireless energy transfer technology enables sensor nodes to maintain perpetual operation. However, maximizing the network performance while preserving short charging delay is a great challenge. In this work, a Wireless Mobile Charger (WMC) and a Directional Charger (DC) are deployed to transmit wireless energy to the sensor node to improve the network's throughput. To the best of our knowledge, this is the first work to optimize the data sensing rate and charging delay by joint scheduling of MC and DC. We prove we can transmit maximum energy to each sensor node to obtain our optimization objective. In our proposed work, a DC selects a total horizon of equipped with DCs, which selects the horizon of each specific area with based on its antenna orientation. DC's orientation is scheduled for each time slot. Furthermore, multiple MCs are used to transmit energy for sensor nodes which cannot be covered by DCs. We divided the Rechargeable Wireless Sensor Network into several zones via the Voronoi diagram. We deployed a static DC and one MC charging location in each zone to provide wireless charging service jointly. We obtain the optimal charging location of MCs in each zone by solving Mix Integral Programming for energy transmission. The optimization objective of our proposed research is to sense maximum data from each sensor node with the help of maximum energy. The lifetime of each sensor network can increase, and the end delay can be maximized with joint energy transmission. Extensive simulation results demonstrate that our RWSNs are designed significantly to improve network lifetime over the baseline method.

Current paper is aiming to show the obtained results in manufacturing and characterization of graphite-based and metal composite materials suitable to be used in high voltage applications of automotive and/or aviation field. Thus, 4 types of materials have been processed and tested in order to assess their suitability to be used as current collector material for electric engines. The novelty of this work is the presentation of the new innovative technological process for obtaining the carbon/metal composite material used in the manufacture of sliding contacts for current collector heads, as well as the characteristics obtained for this material. All 4 obtained materials have been characterized from structural, mechanical and functional point of view and the most suitable of them has been chosen to be further developed by the end beneficiary.

Mobile health technologies enable continuous, quantitative assessment of mobility and gait in real-world environments, facilitating early diagnosis of gait disorders, disease progression monitoring, and prediction of adverse events like falls. Traditionally, mobile gait assessment predominantly relied on body-fixed sensors positioned at the feet or lower trunk. Here, we investigate the potential of an algorithm utilizing an ear-worn motion sensor for spatiotemporal segmentation of gait patterns. We collected 3D acceleration profiles from the ear-worn sensor during varied walking speeds in 53 healthy adults. Temporal convolutional networks were trained to detect stepping sequences and predict spatial relations between steps. The resulting algorithm, mEar, accurately detects initial and final ground contacts (F1 score of 99% and 91%, respectively). It enables determination of temporal and spatial gait cycle characteristics (among others stride time and stride length) with good to excellent validity at a precision sufficient to monitor clinically relevant changes in walking speed, stride-to-stride variability, and side asymmetry. This study highlights the ear as a viable site for monitoring gait and proposes its potential integration with in-ear vital sign monitoring. Such integration offers a practical approach to comprehensive health monitoring and telemedical applications, by integrating multiple sensors in a single anatomical location.

This paper presents a review on numerical and experimental methods to predict fracture of ad-vanced high strength steels (AHSS). AHSS are widely processed through sheet metal forming processes. Although being an excellent choice when lightweight, high strength and ductility are critical factors, their multi-phase microstructure accentuates forming challenges. To accurately model forming behavior, necking based failure criteria as well as direct fracture models require improvements. As a necking based failure model, the conventional forming limit diagram/curve (FLD/FLC) presents limitations such as in estimating direct fracture (surface cracks, edge cracks, shear cracks), as well as deformation histories under nonlinear strain paths. Thus, significant re-search efforts are being made towards the needs of advanced fracture constitutive models capa-ble of predicting fracture scenarios without necking, more frequently observed in the realm of AHSS. Scientific community research is divided into several directions aiming at improving the forming and fracture behavior accuracy of parts subjected to sheet metal forming operations. In this review paper, a comprehensive overview on ductile fracture modeling is presented. Firstly, the FLD/FLC limitations modeling fracture behavior in sheet metal forming operations are stud-ied. Followed by the recent trends in constitutive material modeling. Afterwards, material char-acterization methods advancements to cover a broad range of stress states are comprised. Final-ly, damage and fracture models predicting failure in AHSS are investigated. This review paper supplies relevant information on the current issues the sheet metal forming community is chal-lenged with due to the trend towards AHSS employment in the automotive industry.

Soil contamination and the uptake of contaminants by food crops is a global problem that differs significantly from region to region, with the key factors affecting the contaminants present in local soils being the mineralogical composition of the underlying layers and local human activity. The area of ​​the Pannonian region is known for the fact that agriculture has, historically, played an important role since Roman times, which was particularly influenced by human activity. In this study we performed a preliminary study of the contamination of soil samples across the Pannonian region, to determine the potential presence of harmful contaminants. Both soil and crop samples were analysed for the potential presence of heavy metals, with additional focus placed on the potential presence of microplastics in the region`s soil.

Hydrogen storage in general is an indispensable prerequisite for the introduction of a hydrogen energy based infrastructure. In this respect, high-pressure metal hydride (MH) tank systems appear to be one of the most promising hydrogen storage techniques for automotive applications using proton exchange membrane (PEM) fuel cells. These systems bear the potential of achieving a beneficial compromise of comparably large volumetric storage density, a wide working temperature range, comparably low liberation of heat, and increased safety. The debatable term unstable metal hydride stands in the literature short for metal hydrides with high dissociation pressure at comparably low temperature. Such compounds may help to improve the merit of high-pressure MH tank systems. Consequently, in the last few years, some materials for possible on-board applications in such tank systems have been developed. This review summarizes the state-of-the-art developments of these metal hydrides, mainly including intermetallic compounds and complex hydrides and gives some guidelines for future developments. Since typical laboratory hydrogen uptake measurements are limited to 200 bar, a possible threshold for defining unstable hydrides could be a value of their equilibrium pressure of peq > 200 bar for T < 100°C. However, these values would mark a technological future target and most current materials, and those reported in this review, do not fulfill these requirements and need to be seen as current stages of development towards the intended target. For each of the aforementioned categories in the review, special care was taken not only to covers the pioneering and classical research, but also to portrait the current status and latest advances. For intermetallic compounds, key aspects focus on the influence of partial substitution on absorption/desorption plateau pressure, hydrogen storage capacity and hysteresis properties. For complex hydrides, the preparation procedures, thermodynamics and theoretical calculation are presented. Besides, challenges, perspectives, and development tendency of this field are also discussed.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

Biomaterials are the basis for the development of medicine because they allow safe contact with a living organism. The aim of this work was to produce innovative oxide layers with a porous microstructure on the surface of commercially pure titanium Grade 4 (CpTi G4), and to characterize their properties as drug carriers. Anodization of the CpTi G4 subjected to mechanical grinding and electrochemical polishing was carried out in a solution of 1M ethylene glycol with the addition of 40 g of ammonium fluoride at a voltage of 20 V for 2, 18, 24 and 48 hours at room temperature. It was found that the longer anodization time, the greater the number of pores formed on the CpTi G4 surface as revealed by FE-SEM method, and the greater the surface roughness determined in profilometric tests. As the anodizing time increases, the amount of the drug in the form of gentamicin sulfate incorporated into the resulting pores decreases. The most favorable drug release kinetics profile determined by UV-VIS absorption spectroscopy was found for the CpTi G4 anodized for 2 h making them the best choice when it comes to the drug carrier allowing full use of the therapeutic dose of the drug.

Currently, there is a high interest in smart sensors and integrated composite materials in various industries such as construction, aviation, automobile, medical, information technology, communication, and manufacturing. Here, a new conceptual design for a force and temperature sensor system is developed by integrating fiber optic Bragg grating sensors embedded within composite materials, and a mathematical model is proposed that allows one to estimate strain and temperature based on signals obtained from optical Bragg gratings. This is important for understanding the behaviors of sensors under different conditions and for creating effective monitoring systems. Describing the strain gradient distribution, especially considering different materials with different values of Young's modulus, provides insight into how different materials respond to applied forces and temperature changes. The shape of the strain gradient distribution was obtained, which is a quadratic function with a maximum value of 1500 µ, with a maximum value at the center of the lattice and a symmetrically decreasing strain value with distance from the central part of the fiber Bragg grating. With axial strain at the installation site of the Bragg grating sensor under applied force values ranging from 10 to 11 N, the change in strain was linear. As a result of theoretical research, it was found that the developed system with fiber-optic sensors based on Bragg gratings embedded in composite materials is resistant to external influences and temperature changes.

The discharge of industrial effluents containing toxic heavy metals in water sources has serious consequences for human health and the environment, and biosorption appears to be an environmental-friendly and cost-effective alternative that can be used for wastewater treatment. The use of different types of agricultural waste as biosorbents for the removal of toxic heavy metals, although an alternative, is quite difficult to apply in practice because these wastes have many other uses. Based on these considerations, in this study, soybean biomass (SB), soybean waste biomass obtained from oil extraction (SBW) and biochar obtained from soybean waste pyrolysis (BC-SBW) were testes as biosorbents form the removal of Pb(II) and Cd(II) ions, in batch systems. Under optimal conditions (pH = 5.4, 4.0 g biosorbent/L, room temperature (25 ± 1 C), contact time = 180 min), the biosorption capacity increase in the order: SB &lt; SBW &lt; BC-SBW for both metal ions, indicating that BC-SBW has the highest efficiency in removing toxic heavy metals. In addition, experiments on wastewater samples have shown that, in addition to significant reducing the content of heavy metals, BC-SBW also significant improved other quality indicators (such as: pH, TSM, CCO-Cr, CBO5), compared to the other biosorbents (SB and SBW). Quantitative evaluation of the biosorptive performance of each biosorbent (SB, SBW and BC-SBW) shows that BC-SBW has a real chance of being used on an industrial scale for wastewater treatment. All these aspects allowed the development of a circular approach for the use of soybean biomass in the removal processes of toxic heavy metals. This approach minimizes the shortcomings of using biomass as a biosorbent and increase the chance of using these materials in industrial practice.

Magnetogenetics emerges as a transformative approach for modulating cellular signaling pathways through the strategic application of magnetic fields and nanoparticles. This technique leverages the unique properties of magnetic nanoparticles (MNPs) to induce mechanical or thermal stimuli within cells, facilitating the activation of mechano- and thermosensitive proteins without the need for traditional ligand-receptor interactions. Unlike traditional modalities that often require invasive interventions and lack precision in targeting specific cellular functions, magnetogenetics offers a non-invasive alternative with the capacity for deep tissue penetration and the potential for targeting a broad spectrum of cellular processes. This review underscores magnetogenetics' broad applicability, from steering stem cell differentiation to manipulating neuronal activity and immune responses, highlighting its potential in regenerative medicine, neuroscience, and cancer therapy. Furthermore, the review explores the challenges and future directions of magnetogenetics, including the development of genetically programmed magnetic nanoparticles and the integration of magnetic field-sensitive cells for in vivo applications. Magnetogenetics stands at the forefront of cellular manipulation technologies, offering novel insights into cellular signaling and opening new avenues for therapeutic interventions.

The market for autonomous vehicles (AV) is expected to experience significant growth over the coming decades and to revolutionize the future of transportation and mobility. The AV is a vehicle that is capable of perceiving its environment and perform driving tasks safely and efficiently with little or no human intervention and is anticipated to eventually replace conventional vehicles. Self-driving vehicles employ various sensors to sense and perceive their surroundings and, also rely on advances in 5G communication technology to achieve this objective. Sensors are fundamental to the perception of surroundings and the development of sensor technologies associated with AVs has advanced at a significant pace in recent years. Despite remarkable advancements, sensors can still fail to operate as required, due to for example, hardware defects, noise and environment conditions. Hence, it is not desirable to rely on a single sensor for any autonomous driving task. The practical approaches shown in recent research is to incorporate multiple, complementary sensors to overcome the shortcomings of individual sensors operating independently. This article reviews the technical performance and capabilities of sensors applicable to autonomous vehicles, mainly focusing on vision cameras, LiDAR and Radar sensors. The review also considers the compatibility of sensors with various software systems enabling the multi-sensor fusion approach for obstacle detection. This review article concludes by highlighting some of the challenges and possible future research directions.

This work focuses on the theoretical study of the effect of entanglement in the Yttrium Barium Copper Oxide (YBCO) superconductor on the critical current density, critical magnetic field, and penetration depth. Using the Ginzburg Landau (GL) theory, the expression for the GL coherence length, the critical current density, the lower critical magnetic field (Hc1), and the upper critical magnetic field (Hc2) for the entangled superconducting YBCO was obtained. At zero external magnetic fields, YBCO was found to undergo a transition from the normal state to the superconducting state at 93K and returned to normal. We found a direct relationship between the GL coherence length penetration depth and the temperature of the entangled superconducting YBCO. The graphs of the lower critical magnetic field (Hc1) and critical current density against temperature show a non-linear dependence.In contrast, the graph of the upper critical magnetic field (Hc2) against temperature (T) shows the linear dependence, which is in agreement with existing theoretical observations. On the other hand, the graph of critical current density against the distance of separation between the entangled electrons that form a cooper pair showed that the critical current density increases between 1.8 and 6 nanometers attaining a constant value after reaching 7 nanometers for infinite distances. Finally, for lower critical fields, the magnetic field decreases between 1.5 to 6 nanometers attaining a constant value of the magnetic field, for infinite values of distance of separation between the entangled pair of electrons.

This letter presents a dual-frequency terahertz amplitude modulator based on a cross-shaped structure and U-shaped metal patches. Its structural unit is a typical metal-substrate structure. The top metal consists of a cross-shaped structure and U-shaped metal patches, and the bottom substrate layer is made of quartz. Amplitude modulation is achieved by adjusting the temperature of the vanadium dioxide (VO2) patches. The modulation depth can be approximately 75%. The mechanism of the resonance frequency is explained by the equivalent circuit model. The proposed structure shows good amplitude modulation capability at different incidence and azimuth angles by changing the location of the VO2 patches. The dual-frequency terahertz amplitude modulator can be used in terahertz communication, imaging, etc.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

Present worldwide difficulties in healthcare and the environment have motivated the investigation and research of novel materials in an effort to find novel techniques to address the current chal-lenges and requirements. In particular, the use of nanomaterials has demonstrated a significant promise in the fight against bacterial infections and the problem of antibiotic resistance. Metal na-noparticles and carbon-based nanomaterials in particular have been highlighted for their excep-tional abilities to inhibit many types of bacteria and pathogens. In order for these materials to be as effective as possible, synthetic techniques are crucial. Therefore, in this review article, we high-light some recent developments in the design and synthesis of various nanomaterials, including metal nanoparticles (e.g., Ag, Zn, or Cu), metal hybrid nanomaterials, and the synthesis of mul-ti-metallic hybrid nanostructured materials. Following that, examples of these materials’ applica-tions in antimicrobial performance targeted at eradicating multi-drug resistant bacteria, material protection such as microbiologically influenced corrosion (MIC), or additives in construction ma-terials have been described.

Human Activity Recognition (HAR) technology enables continuous behavior monitoring, particularly valuable in healthcare. This study investigates the viability of using an ear-worn motion sensor for classifying daily activities, including lying, sitting/standing, walking, ascending stairs, descending stairs, and running. Fifty healthy participants (between 20 and 47 years old) engaged in these activities while under monitoring. Various machine learning algorithms, ranging from interpretable shallow models to state-of-the-art deep learning approaches designed for HAR, were employed for classification. Results demonstrate the ear sensor's efficacy, with deep learning models achieving 98% accuracy rate of classification. The obtained classification models are agnostic regarding which ear the sensor is worn and robust against moderate variations in sensor orientation (e.g., due to differences in auricle anatomy), meaning no initial calibration of the sensor orientation is required. The study underscores the ear's efficacy as a suitable site for monitoring human daily activity and suggests its potential for combining HAR with in-ear vital signs monitoring. This approach offers a practical method for comprehensive health monitoring by integrating sensors in a single anatomical location. This integration facilitates individualized health assessments, with potential applications in tele-monitoring, personalized health insights, and optimizing athletic training regimes.

The development of a rapid, sensitive, specific method for detecting foodborne pathogens is paramount in supplying safe food to enhance public health safety. Despite the significant improvement in pathogen detection methods, key issues are still associated with rapid methods, such as distinguishing living cells from dead, pathogenic potential or health risk of the analyte at the time of consumption, detection limit, and sample-to-result. The mammalian cell-based assays analyze pathogens' interaction with the host cells and are responsive to only live pathogens or active toxins. In this study, a human embryonic kidney (HEK293) cell line expressing Toll-Like Receptor 5 (TLR-5) and chromogenic reporter system (HEK dual hTLR5) was used for the detection of viable Salmonella in a 96-well tissue culture plate. This cell line responds to low concentrations of TLR5 agonist flagellin. Stimulation of TLR5 ligand activates nuclear factor-kB (NF-κB) - linked alkaline phosphatase (AP-1) signaling cascade inducing the production of secreted embryonic alkaline phosphatase (SEAP). With the addition of a ρ-nitrophenyl phosphate as a substrate, a colored end product representing a positive signal is quantified. The assay's specificity was validated with the top 20 Salmonella enterica serovars and 19 non-Salmonella spp. The performance of the assay was also validated with spiked food samples. The total detection time (sample-to-result), including shortened pre-enrichment (4 h) and selective enrichment (4 h) steps with artificially inoculated outbreak-implicated food samples (chicken, peanut kernel, peanut butter, black pepper, mayonnaise, and peach) was 15 h when inoculated at 1–100 CFU/25 g sample. These results show the potential of HEK-DualTM hTLR5 cell-based functional biosensors for rapid screening of Salmonella.

This investigation explores the potential of enhancing aqueous zinc-ion batteries (AZIBs) through the introduction of a novel cathode material, NH4V4O10 (NVO), combined with reduced graphene oxide (rGO). Utilizing Density Functional Theory (DFT), it was hypothesized that the incorpora-tion of rGO would increase the interlayer spacing of NVO and diminish the charge transfer in-teractions, thus promoting enhanced diffusion of Zn2+ ions. These theoretical predictions were substantiated by experimental data acquired from hydrothermal synthesis, which indicated a marked increase in interlayer spacing. Significantly, the NVO-rGO composite exhibits remarkable cyclic durability, maintaining 95% of its initial specific capacity of 507 mAh g−1 after 600 cycles at a current density of 5 A g−1. The electrochemical performance of NVO-rGO not only surpasses that of pristine NVO but also outperforms the majority of existing vanadium oxide cathode materials reported in the literature. This study underscores the effective integration of theoretical insights and experimental validation, contributing to the advancement of high-performance energy storage technologies.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

We report the relative humidity (R.H.) sensing response of a resistive sensor, employing sensing layers based on a ternary nanohybrid comprising holey carbon nanohorns (CNHox), potassium chloride (KCl), and polyvinylpyrrolidone (PVP) at mass ratios 7/1/2, 6.5/1.5/2, and 6/2/2 (w/w/w/w). The sensing structure comprises a silicon substrate, a SiO2 layer, and interdigitated transducer (IDT) electrodes. The sensing film is deposited on the sensing structure via the drop-casting method. The sensing layers' morphology and composition are investigated through Scanning Electron Microscopy (S.E.M.) and RAMAN spectroscopy. The ternary hybrid-based thin film resistance increases when the sensors are exposed to R.H., ranging from 0% to 100%. The manufactured devices show a room temperature response comparable to a commercial capacitive R.H. sensor and are characterized by excellent linearity, rapid response time, and good sensitivity. The presented sensors exhibit superior performance in terms of sensitivity compared to other similarly manufactured and tested sensors that employ a CNHox-based sensing layer. We explain the sensing role of each constituent of the ternary hybrid nanocomposites based on their chemical and physical properties, electronic properties, and affinity for water molecules. Different alternative sensing mechanisms are considered and discussed, such as the decreasing number of holes in the holey CNHox at the interaction with water molecules, proton conduction, and PVP swelling.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

In this work, two plasmonic structures with two different periodic nanostructures (nanodisk and nanostrip arrays) separated from the gold layer by an ultrathin dielectric Al2O3 layer are proposed, and their optical properties are simulated as 3-dimensional models using COMSOL Multiphysics software tool. The optical responses, such as the amplification of the electric field and the scattering, absorption and extinction cross sections of the two structures, are investigated and compared. The results show that both structures show strong field enhancement in their gap layer, and the structure with the periodic array of metal nanodisks shows stronger field enhancement and larger absorption, extinction, and scattering cross sections in its dipole resonance wavelength, which is defined as a bright plasmonic mode. In addition, some weaker resonant modes are observed for both structures and the reason for their generation is dis-cussed. The analysis of different possible modes in such structures is crucial for their application in various fields.

Abstract: With the growing integration of the Internet of Things (IoT) in smart buildings, it is crucial to ensure the precise implementation and operation of wireless sensor networks (WSNs). This paper aims to study the implementation aspect of Wireless Sensor Networks (WSNs) in a commercial multi-story building, specifically addressing the difficulty of dealing with variable environmental conditions on each floor. This research addresses the disparity between simulated situations and actual deployments, offering valuable insights that have the potential to signifi-cantly improve the efficiency and responsiveness of building management systems. We obtain real-time sensor data to analyze and evaluate the system’s performance. Our investigation is grounded in the growing importance of incorporating WSNs into buildings to create intelligent environments. By leveraging the capabilities of Contiki operating system, this study employs a specialized simulator to generate simulated data, allowing for a comparison between real-world and simulated scenarios. We provide an in-depth analysis to scrutinize the disparities and commonalities between the datasets obtained from real-world deployments and simulated en-vironments. We highlight the necessity of precise simulation to validate real-life sensor data, shedding light on the challenges and opportunities associated with implementing WSNs in in-telligent buildings. Results obtained show the significance of accurate simulation models for re-liable data representation, providing a roadmap for further developments in the integration of WSNs into intelligent building scenarios. The findings highlight the potential for optimizing living and working conditions based on the real-time monitoring of critical environmental pa-rameters. This includes insights into temperature, humidity, and light intensity, offering oppor-tunities for enhanced comfort and efficiency in intelligent environments.

In the realm of physical activity and sports science, motion tracking emerges as an important tool for specialists aiming to analyze movement data, whether for daily life activities or enhancing athletic performance. This study introduces an innovative approach to motion tracking through the development of a fully embedded smart shoe sensor system, which employs an inertial measurement unit (IMU) affixed to the shoe sole, coupled with six pressure sensors, to provide real-time calculation of individual stride lengths along with other vital movement statistics. Traditional motion tracking methods, which typically rely on various body-attached sensors, often necessitate substantial post-processing, delaying the feedback loop. In contrast, our system is designed to overcome these limitations by offering high-accuracy, real-time feedback with a minimal error rate of 1.88% from our experiments. Such prompt data acquisition facilitates immediate interventions by sports performance coaches or healthcare professionals, significantly contributing to injury prevention and performance enhancement. The experimental outcomes of this study underscore the system’s capability to deliver precise stride length measurements instantaneously, marking a significant advancement in motion tracking technology and its application in sports science and healthcare.

Integrating nanomaterials like carbon nanotubes (CNTs) and iron oxide (Fe₃O₄) into epoxy composites has significant interest due to their potential to enhance mechanical properties. This study evaluates the impact of dispersion quality on the mechanical performance of CNT/Fe₃O₄/Epoxy composites, comparing stirring and sonication methods at three different loadings: 0.1, 0.3, and 0.5 wt.%. Tensile testing revealed that sonicated composites consistently outperformed stirred composites, with a significant increase in elastic modulus and ultimate tensile strength (UTS). However, fracture strain decreased in both composite types compared to pure epoxy, with sonicated composites experiencing a more significant reduction than stirred composites. These results underscore the importance of high-quality dispersion for optimizing mechanical properties.

Objective: This study aimed to assess the impact of artificial intelligence (AI)-driven noise reduction algorithms on metal artifacts and image quality parameters in cone-beam computed tomography (CBCT) images of the oral cavity. Materials and Methods: This retrospective study included 70 patients, 61 of whom were analyzed after excluding those with severe motion artifacts. CBCT scans, performed using a Hyperion X9 PRO 13 × 10 CBCT machine, included images with dental implants, amalgam fillings, orthodontic appliances, root canal fillings, and crowns. Images were processed with ClariCT. AI deep learning model (DLM) for noise reduction. Objective image quality was assessed using metrics such as the differentiation between voxel values (ΔVVs), the artifact index (AIx), and the contrast-to-noise ratio (CNR). Subjective assessments were performed by two experienced readers, who rated overall image quality and artifact intensity on predefined scales. Results: Compared with native images, DLM reconstructions significantly reduced the AIx and increased the CNR (p<0.001), indicating improved image clarity and artifact reduction. Subjective assessments also favored DLM images, with higher ratings for overall image quality and lower artifact intensity (p<0.001). However, the ΔVV values were similar between the native and DLM images, indicating that while the DLM reduced noise, it maintained the overall density distribution. Orthodontic appliances produced the most pronounced artifacts, while implants generated the least. Conclusion: AI-based noise reduction using ClariCT. AI significantly enhances CBCT image quality by reducing noise and metal artifacts, thereby improving diagnostic accuracy and treatment planning. Further research with larger, multicenter cohorts is recommended to validate these findings.