The efficiency of cold steel rolling depends mainly on the quality of the metal-working coolant (MWC) and its cost. In this connection, it is actual to search for new compositions of lubricants and emulsions, which provide the lowest values of the friction coefficients in deformation zone and are obtained by waste recycling in other industries. In this study we have developed new compositions of the MWC on basis of mono- and diglycerides and their esters of boric acid synthesized from the wastes of sunflower oil production. The new compositions of MWC were tested in DSEA on laboratory rolling mill 100x100 with a roll diameter of 100 mm. The efficiency of new MWC during cold rolling of brass L63 samples was determined by factor of metal stretch forming λ. We found the new metal-working coolants to show the most efficiency under higher cobbing that provides the highest metal stretch forming. The composition with 30 % of mono- and diglycerides is the most effective because it provides the minimum coefficient of friction that leads to increase of factor of metal stretch forming. Thereby the metal-working coolants on basis of mono- and diglycerides obtained from the wastes of sunflower oil production can be recommended for use in strip rolling of copper-zinc alloys because of a low cost, availability and high efficiency.

The efficiency of cold sheet and strip rolling of steels and non-ferrous metals in the main depends on the quality of the technological lubricant and its cost. In this regard, it is important to develop new compositions of effective metal-working coolants (MWC) having low cost and providing the maximum reduction in the friction coefficient. We developed and tested the new compositions of the MWC on basis of chicken fat, and mono- and diglycerides and their esters of boric acid synthesized from the wastes of sunflower oil production. The MWC were tested in DSEA on laboratory rolling mill 100x100 with a roll diameter of 260 mm during steel 08Kp rolling. The efficiency of the coolants was determined by the factor of metal stretch forming λ and the coefficient of friction μ in the deformation zone which was found by forward slip method. We found the metal-working coolant with 100 % concentration of boric acid esters of mono- and diglycerides is the most effective in steel rolling. Thus the new MWC on basis of boric acid esters of mono- and diglycerides synthesized from the wastes of sunflower oil production can be recommended for use in rolling of structural steels on account of availability, high efficiency, and a low cost.

Sodium borohydride-closo-hydroborate Na3(BH4)(B12H12) exhibits the high room-temperature ionic conductivity and high electrochemical stability. To study the dynamical properties of this mixed-anion compound at the microscopic level, we have measured the 1H, 11B, and 23Na nuclear magnetic resonance spectra and nuclear spin-lattice relaxation rates over the temperature range of 8 – 573 K. Our 1H and 11B spin-lattice relaxation measurements have revealed two types of reorientational jump motion. The faster motional process attributed to reorientations of the [BH4]− anions is characterized by the activation energy of 159 meV, and the corresponding reorientational jump rate reaches ~10^8 s^-1 near 130 K. The slower process ascribed to reorientations of the larger [B12H12]− anions is characterized by the activation energy of 319 meV, and the corresponding reorientational jump rate reaches ~10^8 s^-1 near 240 K. The results of the 23Na nuclear magnetic resonance measurements are consistent with the fast long-range diffusion of Na+ ions in Na3(BH4)(B12H12). The diffusive jump rate of Na+ is found to reach ~10^4 s^-1 at 300 K and ~8 × 10^8 s^-1 at 530 K. Comparison of these jump rates with the ionic conductivity data suggests the importance of correlations between diffusing ions.

Several studies report an impact of the neurotransmitter dopamine (DA) on human immune cells, with effects dependent on immune cell type addressed and their activation status. Another contributing factor appears to be sex, as sex-specific differences in the dopaminergic pathway are described in the neurological context as well as in autoimmune diseases. However, a deeper understanding of these differences in peripheral immune cells remains limited. In this study, we investigated the effects of dopaminergic stimulation on activation and cytokine secretion of peripheral blood mononuclear cells from women and men using flow cytometry, ELISA and multiplex assay. We found a B cell-driven downregulation in cytokine secretion of monocytes exclusively from women under physiological conditions. Moreover, B cells from men showed higher dopamine receptor (DR) expression, which was shown to be further increased by sex hormones only in men. In monocytes from women, an acute inflammatory stimulus via CpG combined with dopaminergic stimulation caused a switch to a proinflammatory phenotype, which was less pronounced in men. These novel findings in sex-specific responses to dopaminergic stimulation are crucial for understanding DA’s function in the healthy and activated immune system and provide evidence to treat DA-related pathologies in a sex-specific manner.

The article addresses manufacturing structures made of biodegradable materials that can be successfully used as energy-absorbing liner of sports helmets of all kinds, replacing the previously used expanded polystyrene. The paper is focused on injection technological tests and tensile tests (in quasi-static and dynamic conditions) of several composites based on a PLA matrix with the addition of other biodegradable softening agents, such as PBAT and TPS. Next, the thin-walled elements (dimensions of 55 x 55 x 20 mm) were manufactured and evaluated using a spring-loaded drop hammer. The 60J impact energy was tested according to EN 1078 standard. The dynamic crushing testing included checking the influence of the materials temperature (-20, 0, 20, and 40 °C) and the impact velocity. The PLA15PBAT85 blend was selected as the most effective material in terms of its use as energy-absorbing liner for sport helmets.

This paper presents and demonstrates the development of a new lightweight coating for aluminium alloy using a novel multicomponent alloy based on the AlSiMgCu system. This coating was applied using a newly designed approach that combined High-Velocity Oxy-Fuel (HVOF) and Plasma Spraying processes. This hybrid technique enables the deposition of coatings with enhanced performance characteristics. The microstructure was studied using optical microscopy (OM) and scanning electron with energy dispersive X-ray spectroscopy (SEM+EDS) microscopy, revealing good adhesion and compaction between the multicomponent coating and the A6061 substrate with 50 to 150 µm thickness. Vickers indentations were performed on the substrate and the new coating material, revealing a 50% improvement in the material's hardness compared to the casted alloy. Additionally, electrical conductivity measurements showed approximative x3.3 times values compared to the alloy in as-cast condition due to high solidification rates altering the morphology of the phases. Corrosion tests demonstrated a lower corrosion rate compared to other multicomponent aluminium alloys and similar to thermal treated A6061 alloy. Finally, tribological results obtained using ball on disc (BOD) test and laser scanning confocal microscopy, confirmed that the new multicomponent coating exhibited reductions in both friction coefficient and wear rate by more than 20% and 50%, respectively. This study demonstrates that using multi-component aluminium coatings could lead to developing of new automotive parts with enhanced properties for corrosion resistance, electrical conductivity, and wear conditions. Optimizing the thermal spraying parameters could further enhance the coating, achieving greater and more homogeneous thicknesses and yielding even higher performance properties.

The demands for high power and low emissions put focus on energy efficiency when developing new engines. An important part is the UAV engine cooling system, which cools the engine structure below damaging temperatures. For high temperatures in the cooling system there is a risk that boiling occurs and while the initial nucleate boiling enhances the cooling effect, the subsequent Film boiling decreases the heat transfer drastically. It is important to understand the benefits and limitations of various fluids when designing a two-phase cooling system. This paper proposes an alternative organic coolant. Its normal application range is 15°C to 400°C, and its pressure range is from atmospheric to 10.6 bar. DOWTHERM A fluid possesses unsurpassed thermal stability at temperatures of 400°C. This fluid, in both the liquid and vapor form, is noncorrosive toward common metals and alloys. Even at the high temperatures involved, the equipment usually exhibits excellent service life. Original equipment in many systems is still being used after 30 years of continuous service. The numerical results, described in this paper, show the potential of DOWTHERM A as a good alternative for cooling a UAV engine. It will extend the working temperature range of the Diesel engine and will maintain the structural integrity of the piston, cylinder and the piston rings.

Responding to changing value creation processes in the sheet metal working sec-tor, where the complexity and interchangeability of products challenge traditional dif-ferentiation strategies, this empirical analysis explores integrating service-oriented and data-driven business models as new paths to ensure competitiveness, especially for small and medium-sized enterprises (SMEs). This study aims to capture the current state and challenges associated with the implementation of these business models in this sector. The research was conducted through semi-structured interviews with SMEs in the industry. The findings indicate that service-oriented and data-driven business models are not yet widely adopted and that manufacturing companies re-quire support in their implementation. Fields of action were identified for the industry. These are "Creating awareness and understanding", "Recognizing added value", "In-creasing company maturity" and "Understanding the change process". Cooperation between science and industry is essential in tackling these fields of action to ensure the successful integration of such business models in manufacturing companies. This pa-per identifies challenges in the fields of action that companies must address through a structured approach promoting awareness, recognizing value, improving organiza-tional maturity, and understanding the change process to successfully implement ser-vice-oriented and data-driven business models.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

Keywords: liquid alloys, microstratification, dispersed particles, spontaneous dispersion, criteria for true (entropic) spontaneous dispersion, mechanisms of quasi-spontaneous dispersion, methods and results for assessing size of dispersed particles.

Studies have demonstrated the critical role that safety plays in preserving favourable working conditions in the construction industry, which is necessary to accomplish goals. The aim of this research was to inform stakeholders in the construction industry in developing nations about the value of safety and possible strategies for influencing their opinions regarding safety protocols. The importance of safety to the construction sector, which is crucial to the advancement of the country, has also been emphasized. However, due to a lack of adequate safety understanding among stakeholders in the construction sector, the construction industry is characterized by a great deal of instability and hazard. To determine what factors, affect productive working conditions in the construction production, this study examined safety. A conceptual framework for safe working conditions in the construction sector was developed by considering several aspects, including the person dimension, environment factor, safety behaviour, organization features, technology, and incentives. It is now imperative to bring in these dimensions to improve the safe working conditions in the construction industry, particularly in the developing countries. By putting these safety factors into practice, the construction industry can reduce safety risks, lower the number of accidents and fatalities, cut expenses related to subpar safety performance, safeguard the reputation of construction companies, boost employee morale and satisfaction with their work, enhanced employee retention, reduced absenteeism, and enhanced sustainability goals. Additionally, the proposed conceptual framework is assured to be new and to be widely accepted in the developing nations. Based on this assumption the conceptual framework is designed.

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

Background and Objectives: The aim of this study was to determine the job-related and individual features that influence BS and depression levels among dentists working in faculties, oral and dental health centres (ODHC) and private clinics. Materials and Methods: This prospective, cross sectional study was carried out on dentists working in different regions of Turkey. Data were collected using an on-line questionnaire created using Google Forms. The questionnaire consisted of demographic data, Maslach BS Inventory (MBI) and Beck Depression Inventory (BDI) sections. Demographics were age, height, weight, marital status, blood type, gender, monthly income, income satisfaction and having enough free time. The dentists were divided into 3 groups as faculty, private clinic and ODHC according to the institutions in which they worked. Results: Of the total 290 dentists enrolled in the study, there were 172 males and 118 females with a mean age of 36.98±5.6 years. 128 of the dentists worked in faculties, 72 in private clinics and 90 in ODHCs. It was observed that women's EE scores were higher than men's (P<0.05). No statistically significant difference was found between the groups when comparing BS and depression scores according to marital status and blood group (P>0.05). There was no significant relationship between emotional exhaustion (EE), depersonalisation (DP), personal accomplishment (PA) and depression scores according to age, BMI and work experience, age, work experience and BMI (P<0.05). It was found that the EE scores of the dentists working in the faculty and private clinic were lower than those of the dentists working in the ODHC (P<0.05). Monthly income was associated with depression (r = -0.35). Conclusions: This study showed that dentists working in ODHCs had more EE. These findings suggest that there is a need for improvement in the working conditions of dentists, particularly in ODHCs.

: The performance of the students in academics depends on many different factors. One of these factors is the economic status of their families. Education in public schools, though it is free, some parents cannot afford to send their children to school due to financial constraints. Education as a free is every individual's right in society, but it becomes a privilege because of a lack of financial support. This research work is a comparative study of students' or learners' performance in mathematics among students from working and non-working. This research article's ultimate objective is to investigate and compare a significant difference in their performance in the subject mathematics. The research methodology utilizes a t-test to analyze and synthesize primary data sources collected via interview and academic records, and diverse literature on the study area. However, the research findings revealed no significant difference in the two groups (the working and non-working group of learners). Therefore, it is recommended that secondary schools should be provided with adequate books and facilities and faculty school interventions and programs and promote the usage of SIM or Strategic Intervention Materials for learning and memory enhancement among learners.

The continuous casting process of helical fiber reinforced metal matrix composites was proposed, and the experimental equipment was designed and manufactured. The relationship model be-tween the process parameters and the helical shape of the fibers in the metal matrix is analyzed by differential geometry. Helical carbon fiber reinforced lead matrix composites were prepared under different conditions. When the melting temperature and cooling intensity were increased, the helical radius of helical carbon fiber in lead matrix was increased. When the fiber rotation speed was increased, the helical radius was decreased, and the helical pitch was de-creased proportionally. The experimental results are consistent with the process model. Carbon fiber rein-forced aluminum composites were prepared. Scanning electron microscopy showed that the infiltration between the aluminum matrix and the carbon fiber was not complete. As the volume fraction of carbon fiber which was added in composites is too small, the mechanical properties of the composites have not been significantly improved.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

The capability of large food retail chains to respond quickly to changes in consumer behaviour and their dominant market position affects all food market players and often conflicts with the interests of national food producers, which can reduce the presence of locally sourced products in the food product mix in the country. In Latvia, there have been several proposals to limit retailers' opening hours on weekends and public holidays to increase the viability of small local food producers, retailers, and catering enterprises; however, limiting retailers' opening hours without research-based arguments is unacceptable. The research studies conducted in Europe also do not give a unified conclusion. Household consumer behaviour in the food market is viewed as an essential argument for increasing domestic demand and economic stability. Accordingly, the present research aims to identify the impacts of diversification of opening hours of food supermarkets on consumer shopping habits and the implications for creating an advantage for small and medium agri-food producers in selling their products. The research applied a quantitative approach to identify the main trends in society (n=2738), with a survey including 31 variables to quantify consumer behaviour, values, and opinions and seven socio-demographic variables. If a decision were made in Latvia to close grocery shops on Sundays or reduce their opening hours on weekends, 85% of consumers indicated that they would be unlikely to change their usual shopping location and would plan to shop at a supermarket on other days. The choice between farmers' markets and local food shops on Sundays would be made by 45% of consumers, with more than half (53%) of them shopping at local food shops at least a few times a month. It could, therefore, be argued that reducing the opening hours of supermarkets and closing them on Sundays and public holidays do not provide a competitive advantage and do not divert consumers to small and medium agri-food producers.

In this paper we present magnetoelectric properties of metal/metal-oxide/metal junctions. We use Ti and Fe as metallic layers separated by the porous metal-oxides of iron or titanium formed with the anodization method. This allowed to prepare double junctions with at least one ferromagnetic layer. Here we show magnetoresistance and current-voltage characteristics of the junctions together with their magnetic characteristics. We found positive or negative magnetoresistance depending on junction composition. We discuss also the nature of differential resistance calculated from I-V characteristics. Our findings show that the strongest influence on observed behaviour has a top metallic layer and the interface between this layer and anodized oxide where strong interatomic diffusion is expected.

Among the various types of gas sensors, the chemoresistive gas sensors based on metal oxides are considered the most attractive ones due to their simple operation, low costs and miniaturization. Thin films of V2O5 undoped and doped with TiO2 were studied as nitrogen dioxide, methane and hydrogen sensors. The experimental kinetics of the electrical conductivity changes due to introduction and removal of gas on metal oxide gas sensors were successfully explained in terms of the Langmuir adsorption theory.

Cu₆Sn₅ whiskers precipitated in Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer were found and investigated after reflow soldering and during aging. Ag₃Sn fibers can be observed around Cu₆Sn₅ whiskers in the matrix microstructure, which can play an active effect on the reliability of interconnection. Different morphologies of Cu₆Sn₅ whiskers can be observed, and hexagonal rod structure is the main morphology of Cu₆Sn₅ whiskers. A hollow structure can be observed in hexagonal Cu₆Sn₅ whiskers, and a screw dislocation mechanism was used to represent the Cu₆Sn₅ growth. Based on mechanical property testing and finite element simulation, Cu₆Sn₅ whiskers were regarded as having a negative effect on the durability of Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer.

Semisolid casting can provide excellent castings, but the nature of the pore-forming mechanisms has not been properly clarified. In the current communication, it was suggested that hydrogen precipitated during slurry making might have a decisive role in the formation of both gas and shrinkage porosity. Intensive stirring at the end of the slurry making process may act as a degassing step. Without the intense stirring, structures of primary slurry particles form around the hydrogen pores, strongly affecting pore formation and feeding during the intensification stage.

Peru has one of the highest informal employment rates in Latin America (73%). Previous studies have shown higher prevalence of poor self-perceived health (P-SPH) in informal workers compared to formal. The study’s aim is to analyse the role of working conditions in the association between informality and SPH in urban working population in Peru. We conducted a cross-sectional study based on 3098 workers from the working conditions survey of Peru 2017. Prevalence of P-SPH and exposure to poor working conditions were calculated separated by formal and informal employment and stratified by sex. Poisson regression models were used to assess the association between P-SPH and informal employment, with its prevalence ratios (PR) crude and adjusted for working conditions. Informal employment was 76% in women and 66% in men. Informal workers were more exposed to poor working conditions than formals and reported worse SPH. Workers in informal employment showed higher risk of P-SPH than formals: PR 1.38 [95% CI: 1.16 – 1.64] in women and PR 1.27 [95% CI: 1.08 – 1.49] in men. Adjustment by working conditions weakened the association in both sexes. In women, this association was only partially explained by worse working conditions 1.23 [95% CI: 1.04 – 1.46]. The negative effect on informal workers’ health is partially explained by poor working conditions. However, there is a part of the effect explained by informality per se.

Heavy metal pollution poses a significant threat to ecosystems and human health worldwide. In response to this pressing issue, bioremediation has emerged as a promising approach for mitigating contamination. This paper adopts a bibliographic method to explore the key techniques and applications of bioremediation. Furthermore, we delve into the most prominent threats to human environmental health and the corresponding remediation methods. Additionally, we discuss the future trajectory of bioremediation research, with a particular focus on the integration of big data and machine learning technologies. These advanced methodologies hold great potential for enhancing the effectiveness and efficiency of environmental remediation efforts in the face of escalating pollution challenges.

Recent research has suggested that working memory training interventions may benefit children with Developmental Language Disorder (DLD). The current study investigated a short and engaging adaptive working memory intervention that targeted executive skills and aimed to improve both language comprehension and working memory abilities in children with DLD. Forty-seven 6- to 10-year-old children with DLD were randomly allocated to an executive working memory training intervention (n=24) or an active control group (n=23). A pre-test/intervention/post-test/9-month-follow-up design was used. Outcome measures included assessments of language (to evaluate far transfer of the training) and working memory (to evaluate near transfer of the training). Hierarchical multiple regression analyses controlling for pre-intervention performance and age found group to be a significant predictor of sentence comprehension and of performance on six untrained working memory measures at post-intervention and 9-month follow-up. Children in the intervention group showed significantly higher language comprehension and working memory scores at both time points than children in the active control group. The intervention programme showed potential to improve working memory and language comprehension in children with DLD and demonstrated several advantages: it involved short sessions over a short period; caused little disruption in the school day; and was enjoyed by children.

This study investigates the impact of circular economy (CE) strategies on organizational resilience (OR) within the metal industry, focusing on a case study of a forging department in a large man-ufacturing company. The idea of the paper is to link the macroeconomic topic of circular economy (CE) with microeconomic and practical activities in the organization, exploring how CE principles can improve resource efficiency, sustainability, and organizational resilience. A systematic literature review and case study methodology were used to assess the relationship between CE and OR. The findings reveal that companies with higher circularity demonstrate better resilience, both in normal operations and during crises. Specifically, in the case study, the closure of the forging department, following a detailed analysis using the Inputs-Mediators-Outputs (IMO) model, emerged as the most sustainable option, yielding financial, environmental, and operational benefits. This decision aligned with the company’s long-term goals of energy efficiency and carbon neutrality. The research highlights the significance of integrating CE strategies with business processes to not only achieve sustainability but also to build a more adaptable and resilient organization. Future research should explore broader applications of this framework across different industries to strengthen the links between circular economy practices and organizational resilience.

The impulse of the Fourth Industrial Revolution is triggering the demand for few specific metals. These include copper, silver, gold, and platinum group metals (PGMs), with important applications in renewable energies, green hydrogen, and electronic products. However, the continuous extraction of these metals is leading to a rapid decline in their ore grades and, consequently, increasing the environmental impact of extraction. Hence, obtaining metals from secondary sources, such as waste electrical and electronic equipment (WEEE), becomes imperative for both environmental sustainability and ensuring availability. This recovery entails few problems such as allocation due to the simultaneous production of several metals, the use of non-renewable resources, and the exergy destruction during the life cycle of the metals. Therefore, this work analyses the waste printed circuit boards (PCBs) recycling process by proposing different exergy-based cost allocations for the mentioned metals, disaggregating the exergy cost into non-renewable and renewable, and considering the complete life cycle of metals with the Circular Thermoeconomics methodology. The results show a significant saving of non-renewable energy by using renewable energies in primary extraction (67-87%), recycling (97.6-98.5%), and renewable energies in recycling (98.7%, 99.0%), compared to conventional primary extraction. However, when considering the entire life cycle, between 47% and 53% of the non-renewable exergy is destroyed during recycling. Therefore, delaying recycling as much as possible would be the most desirable option for maximizing the use of non-renewable resources, which nature cannot replace in a short time.

The Internet of Things (IoT) technology connects the real world and the network world by integrating sensors and internet technology, which has greatly changed people's lifestyles, showing its broad application prospects. However, traditional materials for the sensors and power components used in IoT limit its development to high-precision detection, long-term endurance, and multi-scenario applications. Metal halide perovskite, with the unique advantages such as excellent photoelectric properties, adjustable bandgap, flexibility, and mild process, exhibiting enormous potential to meet the requirements for IoT development. This paper provides a comprehensive review of metal halide perovskites' application in sensors and energy supply modules within IoT systems. Advances on perovskite-based sensors were discussed as to gas, humidity, photoelectric, and optical sensors. The application of indoor photovoltaics based on perovskite in IoT systems were also discussed. At last, the application prospects and challenges of perovskite-based devices in IoT are summarized.

Sick leave is influenced by various modifiable lifestyle factors and sex differences. This study examines the impact of body mass index, fruit and vegetable consumption, physical activity, smoking, and alcohol consumption on sick leave among Serbia's working population, focusing on sex differences. Data from the 2019 National Health Survey of Serbia were analyzed, focusing on a representative sample of 4,652 individuals aged 18-65. Chi-square tests and logistic regression models assessed the relationships between lifestyle factors and sick leave, adjusting for sociodemographic, work-related, and health-related variables. Among respondents, 15.8% reported sick leave in the past 12 months, with higher rates among women in both, short-term (13.9% vs. 10.6%) and long-term sick leave (3.4% vs. 2.2%). For men, obesity (OR = 2.6), poor dietary habits (fruit OR = 2.1; vegetables OR = 2.8), smoking (OR = 1.9), and risky alcohol consumption (OR = 4.1) significantly increase the likelihood of sick leave. In women, smoking (OR = 1.8) and risky alcohol consumption (OR = 3.1) are major predictors, while BMI and physical activity show less impact. Fruit and vegetable consumption and physical activity have inconsistent effects on sick leave, indicating the need for further research. This study identifies obesity, poor dietary habits, smoking, and alcohol consumption as key predictors of sick leave in men. In women, smoking and risky alcohol consumption are major predictors. Smoking is a risk factor for both sexes, while risky alcohol consumption emerges as a prominent predictor and is a significant predictor overall. These findings highlight the need for targeted public health interventions to address these lifestyle factors and reduce sick leave rates. Further research is needed to clarify the roles of dietary habits and physical activity in influencing sick leave.

This study provides an in-depth review of the available literature on metal composite material machining, focusing on traditional machining operations such as turning, milling, shaping, drilling, and grinding. The motivation for the study is that this composite type has emerged as a vital material in applications requiring functionality, resilience, cost-effective operation, low consumption of energy and lightweight. Despite its superior characteristics, the manufacturing complexity and poor machinability of metal matrix composites have been the primary barriers to its adoption. Nevertheless, there is a reduction of exceptional efficiency, increase in surface roughness, tool wear and so on in metal matrix composites throughout machining. As a result, this review gives a comprehensive investigation of metal matrix composite machining and effect on process parameters and procedures. Furthermore, this study distinguishes metal matrix composites towards sustainable manufacturing and the metals employed by the researchers, as well as the gaps discovered for future recommendations in metal-based composites.

This research aimed to study and compare prevalence of work-related musculoskeletal (MSK) problem and perceived discomfort among port crane operators consisting of quay and rubber tyred gantry (RTG) cranes working in the Laem Chabang Deep-sea Port, Thailand. Direct interviews for a cross-sectional analysis was selected for this unique job with a small amount of sample size. A standardized modified version of the Nordic Musculoskeletal Questionnaire (NMQ) was lunched for 26 male participants, consisting of 11 quay and 15 RTG, where a priori power analysis using G*Power suggested the minimum as 24 for the hypothesis test. Socio-demographic characteristics showed no significant difference among them. The NMQ revealed lower back as the highest prevalent body part (76.9%) followed by neck, shoulders and upper back at the same percentage (23.1%) for all port crane group, with up to 96.2% reporting MSK problem over the past 12 months. And Borg scale rating, assessing the perceived discomfort, revealed lower back with the highest score (2.38) followed by upper back (0.65), shoulders (0.54) and neck (0.5). Remarkably, the comparation between the quey and RTG crane operators on the MSK prevalence (χ2 test) and perceived discomfort levels (Kruskal-Wallis test), regarding different 9 body parts, revealed a significant difference between the two on upper back with quay crane having more problem than the RTG at p < 0.05. while the rest of them were mainly in the same direction. MSK contributors such as: working awkward posture, mental stress, height, trolley distance and vibration are considerably the main causes of this. However, the larger in scale of exposure to those for the quey crane compared to the RTG might have led to the distinguishing MSK problem found in this study which require thoroughly deliberation for the particular solutions.

Robotic-assisted hip and knee arthroplasty represents significant advancements in orthopedic surgery. Artificial intelligence (AI) - driven chatbots, such ChatGP, plays a significant role in healthcare education. This study aims to evaluate the quality of responses provided by ChatGPT to the top 20 questions concerning robotic-assisted hip and knee arthroplasty.We have asked ChatGPT to select the top 20 questions on Google concerning robotic hip and knee arthroplasty and to provide a detailed answer to each of them. The accuracy of the information provided were examined by three orthopedic surgeons with scientific and clinical experience in hip and knee replacement surgery. The accuracy was assessed through a 5-point Likert scale (from 1 – completely incorrect to 5 – correct); the completeness through a 4-point Likert scale (from 0 – comprehensiveness not assessable for completely incorrect answers to 3 – exhaustive information) on two different occasions to ensure the consistency of the assessment. Our analysis reveals that ChatGPT provides a relatively high degree of accuracy, moreover the explanations can be considered satisfy, especially for factual questions. The findings suggest that ChatGPT can serve as a valuable initial resource for general information on robotic hip and knee arthroplasty but the integration with human expertise remains essential.

In Belgium, sex work was recently decriminalized to enhance street-based sex workers’ (SSWs) health. This qualitative study explores stakeholders' perceptions of the impact of the working environment on street-based sex workers’ occupational safety, health and well-being in Brussels. In-depth interviews with seven stakeholders directly involved with SSWs were conducted with data analyzed using qualitative content analysis. The analysis of study data resulted in one theme: “A power imbalance and a lack of concerted efforts among stakeholders are detrimental to the occupational safety, health, and well-being of street-based sex workers”. In Brussels, the majority of SSWs face various challenges due to structural vulnerabilities, thus limiting their choices regarding their work environment, and further compromising their health. Limited access to resources and severe constraints within their working environment contribute to a lack of safety and adverse health outcomes. A stigma mechanism fueled by ideology and personal interests prevent the enforcement of their rights regarding their working environment, safety and health promotion. The lack of involvement of key stakeholders, especially from the public sector, prevents the majority of SSWs in Brussels from benefiting from a sound working environment and the promotion of their health, safety and well-being.

Advanced Finite Element (FE) modeling and simulations were performed on vehicular crashes into a Three-bar Metal Bridge Rail (TMBR). The FE models of a sedan, a pickup truck, and a TMBR section were adopted in the crash simulations subject to Manual for Assessing Safety Hardware (MASH) Test Level 2 (TL-2) and Test Level 3 (TL-3) requirements. The test vehicle models were first validated using full-scale physical crash tests conducted on a two-bar metal bridge using a sedan and a pickup truck with similar overall physical properties and sizes to their respective vehicles used in the simulations. The validated vehicular models were then used to evaluate the crash performance of the TMBR using MASH Evaluation Criteria for structural adequacy, occupant risk, and post-impact trajectory. The TMBR met all MASH TL-2 requirements but failed to meet the MASH TL-3 Criteria H and N requirements when impacted by the sedan. The TMBR was also evaluated under in-service conditions (behind a 1.52-m wide sidewalk) and impacted by the sedan under MASH TL-3 conditions. The simulation results showed that the TMBR behind a sidewalk met all safety requirements except for the occupant impact velocity in the longitudinal direction, which exceeded the MASH limit by 3.93%.

Current paper is aiming to show the obtained results in manufacturing and characterization of graphite-based and metal composite materials suitable to be used in high voltage applications of automotive and/or aviation field. Thus, 4 types of materials have been processed and tested in order to assess their suitability to be used as current collector material for electric engines. The novelty of this work is the presentation of the new innovative technological process for obtaining the carbon/metal composite material used in the manufacture of sliding contacts for current collector heads, as well as the characteristics obtained for this material. All 4 obtained materials have been characterized from structural, mechanical and functional point of view and the most suitable of them has been chosen to be further developed by the end beneficiary.

Hearing loss that arises from various causes at different stages of life has a direct impact on individuals' physical and mental well-being. This paper aimed to evaluate the employment, workplace adaptation, productivity, and professional success of individuals who have hearing loss and whose hearing loss is corrected with a cochlear implant. In this cross-sectional study, the data was collected between November 2022 and March 2023 with the participation of individuals with cochlear implants living in several settlements in all regions of Türkiye. A total of 142 participants with severe hearing loss who were corrected with a cochlear implant were included in this study. The survey method was used to collect data for the study. The questionnaire consisted of 32 questions and was distributed to the participants online. In the first part of the questionnaire (1-10 questions), general characteristics of implant patients were investigated. In the second part (11-32 questions), the positive or negative effects of implantation on the work life of the participants were evaluated. Almost half of the research group (49.3%, n = 70) consisted of women, and the mean age of the participants was determined to be 35.8 ± 14.8. There was no significant difference between gender, educational status, implanted side, working time, working style (physical, desk), and factors affecting work life (p > 0.05). Professional satisfaction and success at work increased significantly more in those with acquired hearing loss (p = 0.010). Post-implantation workplace compliance, success, and productivity were found to be higher in those with acquired hearing loss (p = 0.013). It was observed that hearing loss had a greater negative impact on the work life of married people (p = 0.006). Cochlear implantation greatly enhances workplace satisfaction, increases self-confidence, and has a positive impact on the future of profoundly deaf individuals.

This paper presents a review on numerical and experimental methods to predict fracture of ad-vanced high strength steels (AHSS). AHSS are widely processed through sheet metal forming processes. Although being an excellent choice when lightweight, high strength and ductility are critical factors, their multi-phase microstructure accentuates forming challenges. To accurately model forming behavior, necking based failure criteria as well as direct fracture models require improvements. As a necking based failure model, the conventional forming limit diagram/curve (FLD/FLC) presents limitations such as in estimating direct fracture (surface cracks, edge cracks, shear cracks), as well as deformation histories under nonlinear strain paths. Thus, significant re-search efforts are being made towards the needs of advanced fracture constitutive models capa-ble of predicting fracture scenarios without necking, more frequently observed in the realm of AHSS. Scientific community research is divided into several directions aiming at improving the forming and fracture behavior accuracy of parts subjected to sheet metal forming operations. In this review paper, a comprehensive overview on ductile fracture modeling is presented. Firstly, the FLD/FLC limitations modeling fracture behavior in sheet metal forming operations are stud-ied. Followed by the recent trends in constitutive material modeling. Afterwards, material char-acterization methods advancements to cover a broad range of stress states are comprised. Final-ly, damage and fracture models predicting failure in AHSS are investigated. This review paper supplies relevant information on the current issues the sheet metal forming community is chal-lenged with due to the trend towards AHSS employment in the automotive industry.

Soil contamination and the uptake of contaminants by food crops is a global problem that differs significantly from region to region, with the key factors affecting the contaminants present in local soils being the mineralogical composition of the underlying layers and local human activity. The area of ​​the Pannonian region is known for the fact that agriculture has, historically, played an important role since Roman times, which was particularly influenced by human activity. In this study we performed a preliminary study of the contamination of soil samples across the Pannonian region, to determine the potential presence of harmful contaminants. Both soil and crop samples were analysed for the potential presence of heavy metals, with additional focus placed on the potential presence of microplastics in the region`s soil.

Hydrogen storage in general is an indispensable prerequisite for the introduction of a hydrogen energy based infrastructure. In this respect, high-pressure metal hydride (MH) tank systems appear to be one of the most promising hydrogen storage techniques for automotive applications using proton exchange membrane (PEM) fuel cells. These systems bear the potential of achieving a beneficial compromise of comparably large volumetric storage density, a wide working temperature range, comparably low liberation of heat, and increased safety. The debatable term unstable metal hydride stands in the literature short for metal hydrides with high dissociation pressure at comparably low temperature. Such compounds may help to improve the merit of high-pressure MH tank systems. Consequently, in the last few years, some materials for possible on-board applications in such tank systems have been developed. This review summarizes the state-of-the-art developments of these metal hydrides, mainly including intermetallic compounds and complex hydrides and gives some guidelines for future developments. Since typical laboratory hydrogen uptake measurements are limited to 200 bar, a possible threshold for defining unstable hydrides could be a value of their equilibrium pressure of peq > 200 bar for T < 100°C. However, these values would mark a technological future target and most current materials, and those reported in this review, do not fulfill these requirements and need to be seen as current stages of development towards the intended target. For each of the aforementioned categories in the review, special care was taken not only to covers the pioneering and classical research, but also to portrait the current status and latest advances. For intermetallic compounds, key aspects focus on the influence of partial substitution on absorption/desorption plateau pressure, hydrogen storage capacity and hysteresis properties. For complex hydrides, the preparation procedures, thermodynamics and theoretical calculation are presented. Besides, challenges, perspectives, and development tendency of this field are also discussed.

The discharge of industrial effluents containing toxic heavy metals in water sources has serious consequences for human health and the environment, and biosorption appears to be an environmental-friendly and cost-effective alternative that can be used for wastewater treatment. The use of different types of agricultural waste as biosorbents for the removal of toxic heavy metals, although an alternative, is quite difficult to apply in practice because these wastes have many other uses. Based on these considerations, in this study, soybean biomass (SB), soybean waste biomass obtained from oil extraction (SBW) and biochar obtained from soybean waste pyrolysis (BC-SBW) were testes as biosorbents form the removal of Pb(II) and Cd(II) ions, in batch systems. Under optimal conditions (pH = 5.4, 4.0 g biosorbent/L, room temperature (25 ± 1 C), contact time = 180 min), the biosorption capacity increase in the order: SB &lt; SBW &lt; BC-SBW for both metal ions, indicating that BC-SBW has the highest efficiency in removing toxic heavy metals. In addition, experiments on wastewater samples have shown that, in addition to significant reducing the content of heavy metals, BC-SBW also significant improved other quality indicators (such as: pH, TSM, CCO-Cr, CBO5), compared to the other biosorbents (SB and SBW). Quantitative evaluation of the biosorptive performance of each biosorbent (SB, SBW and BC-SBW) shows that BC-SBW has a real chance of being used on an industrial scale for wastewater treatment. All these aspects allowed the development of a circular approach for the use of soybean biomass in the removal processes of toxic heavy metals. This approach minimizes the shortcomings of using biomass as a biosorbent and increase the chance of using these materials in industrial practice.

Green synthesis offers a superior alternative to traditional methods for producing metal and metal oxide nanoparticles. This approach is not only benign and safe but also cost-effective, scalable, and straightforward, operating under ambient conditions. Notable metals and metal oxide nanoparticles, such as manganese oxides, iron oxides, silver, and gold, have been produced using various bio-reductants derived from plant extracts. These biological agents not only expedite the reduction process but also stabilize the nanoparticles, serving dual roles as reducing and capping agents. This review presents the green synthesis of nanoparticles (NPs) obtained from biogenic wastes and plant extracts. The green-synthesized nanostructured MnO2 are evaluated as a potential photocatalyst for water treatment and as an electrode material in lithium-ion batteries and supercapacitors. The green-derived iron oxide nanoparticles are examined as promising antioxidant, anti-inflammatory, and anti-diabetic agents. Additionally, this review discusses the green synthesis of precious metal nanoparticles, specifically silver (Ag NPs) and gold (Au NPs), highlighting their potential medical applications in areas like antiviral treatments and cancer therapy.

Magnetogenetics emerges as a transformative approach for modulating cellular signaling pathways through the strategic application of magnetic fields and nanoparticles. This technique leverages the unique properties of magnetic nanoparticles (MNPs) to induce mechanical or thermal stimuli within cells, facilitating the activation of mechano- and thermosensitive proteins without the need for traditional ligand-receptor interactions. Unlike traditional modalities that often require invasive interventions and lack precision in targeting specific cellular functions, magnetogenetics offers a non-invasive alternative with the capacity for deep tissue penetration and the potential for targeting a broad spectrum of cellular processes. This review underscores magnetogenetics' broad applicability, from steering stem cell differentiation to manipulating neuronal activity and immune responses, highlighting its potential in regenerative medicine, neuroscience, and cancer therapy. Furthermore, the review explores the challenges and future directions of magnetogenetics, including the development of genetically programmed magnetic nanoparticles and the integration of magnetic field-sensitive cells for in vivo applications. Magnetogenetics stands at the forefront of cellular manipulation technologies, offering novel insights into cellular signaling and opening new avenues for therapeutic interventions.

This letter presents a dual-frequency terahertz amplitude modulator based on a cross-shaped structure and U-shaped metal patches. Its structural unit is a typical metal-substrate structure. The top metal consists of a cross-shaped structure and U-shaped metal patches, and the bottom substrate layer is made of quartz. Amplitude modulation is achieved by adjusting the temperature of the vanadium dioxide (VO2) patches. The modulation depth can be approximately 75%. The mechanism of the resonance frequency is explained by the equivalent circuit model. The proposed structure shows good amplitude modulation capability at different incidence and azimuth angles by changing the location of the VO2 patches. The dual-frequency terahertz amplitude modulator can be used in terahertz communication, imaging, etc.

Present worldwide difficulties in healthcare and the environment have motivated the investigation and research of novel materials in an effort to find novel techniques to address the current chal-lenges and requirements. In particular, the use of nanomaterials has demonstrated a significant promise in the fight against bacterial infections and the problem of antibiotic resistance. Metal na-noparticles and carbon-based nanomaterials in particular have been highlighted for their excep-tional abilities to inhibit many types of bacteria and pathogens. In order for these materials to be as effective as possible, synthetic techniques are crucial. Therefore, in this review article, we high-light some recent developments in the design and synthesis of various nanomaterials, including metal nanoparticles (e.g., Ag, Zn, or Cu), metal hybrid nanomaterials, and the synthesis of mul-ti-metallic hybrid nanostructured materials. Following that, examples of these materials’ applica-tions in antimicrobial performance targeted at eradicating multi-drug resistant bacteria, material protection such as microbiologically influenced corrosion (MIC), or additives in construction ma-terials have been described.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

The practice of telework, remote work, and working from home has grown significantly across the pandemic era (2020+). These practices offer new ways of working but come with a lack of clarity as to the role it plays in supporting the wellbeing of staff. (1) Background: the purpose of this study is to examine the current literature on wellbeing outcomes and effects of telework; (2) Methods: this study adopts a systematic literature review from 2000-2022 using the PRISMA approach and thematic analysis guided by the United Nations Sustainable Development Goals (Wellbeing, Decent Work, Gender Equality, and Inclusive Production); (3) Results: it was evident that there is a lack of clarity on the actual effects of telework on employee wellbeing, but it appeared that it had a generally positive effect on short-term wellbeing of staff, and created more flexible and proactive work design opportunities; (4) Conclusions: there is a need for more targeted research into work designs that support wellbeing and productivity of staff, and consider the environmental sustainability changes from reduced office and onsite work and increased working from home.

This study investigated gender differences in exposure to hazardous factors, health problems, and work environment satisfaction and identified the effects of such differences on farmworkers in Korea. Through the 6th Korean Working Conditions Survey (KWCS) conducted by the Occupational Safety and Health Research Institute (OSHRI), the raw data on 2,347 farm-workers were analyzed to present descriptive statistics for demographic characteristics, exposure to hazardous factors, health problems, and work environment satisfaction. We compared be-tween genders using chi-squared tests and investigated the effects of gender-specific working conditions on work-related health problems and work environment satisfaction using multi-variate logistic analysis. The results were presented as an odds ratio (OR) with 95% confidence interval. Job position predicted work-related health problems in male farmworkers and work environment satisfaction in female farmworkers. Furthermore, female farmworkers perceived themselves to have more health problems than male farmworkers. Nevertheless, female farm-workers received less health and safety information and had lower work environment satisfac-tion compared to male farmworkers. The findings may improve the occupational welfare of farmworkers through continuous enhancement of the agricultural labor environment. Keywords: work-related; working condition; farmworker; agriculture; musculoskeletal; KWCS

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

In this work, two plasmonic structures with two different periodic nanostructures (nanodisk and nanostrip arrays) separated from the gold layer by an ultrathin dielectric Al2O3 layer are proposed, and their optical properties are simulated as 3-dimensional models using COMSOL Multiphysics software tool. The optical responses, such as the amplification of the electric field and the scattering, absorption and extinction cross sections of the two structures, are investigated and compared. The results show that both structures show strong field enhancement in their gap layer, and the structure with the periodic array of metal nanodisks shows stronger field enhancement and larger absorption, extinction, and scattering cross sections in its dipole resonance wavelength, which is defined as a bright plasmonic mode. In addition, some weaker resonant modes are observed for both structures and the reason for their generation is dis-cussed. The analysis of different possible modes in such structures is crucial for their application in various fields.

Objective: This study aimed to assess the impact of artificial intelligence (AI)-driven noise reduction algorithms on metal artifacts and image quality parameters in cone-beam computed tomography (CBCT) images of the oral cavity. Materials and Methods: This retrospective study included 70 patients, 61 of whom were analyzed after excluding those with severe motion artifacts. CBCT scans, performed using a Hyperion X9 PRO 13 × 10 CBCT machine, included images with dental implants, amalgam fillings, orthodontic appliances, root canal fillings, and crowns. Images were processed with ClariCT. AI deep learning model (DLM) for noise reduction. Objective image quality was assessed using metrics such as the differentiation between voxel values (ΔVVs), the artifact index (AIx), and the contrast-to-noise ratio (CNR). Subjective assessments were performed by two experienced readers, who rated overall image quality and artifact intensity on predefined scales. Results: Compared with native images, DLM reconstructions significantly reduced the AIx and increased the CNR (p<0.001), indicating improved image clarity and artifact reduction. Subjective assessments also favored DLM images, with higher ratings for overall image quality and lower artifact intensity (p<0.001). However, the ΔVV values were similar between the native and DLM images, indicating that while the DLM reduced noise, it maintained the overall density distribution. Orthodontic appliances produced the most pronounced artifacts, while implants generated the least. Conclusion: AI-based noise reduction using ClariCT. AI significantly enhances CBCT image quality by reducing noise and metal artifacts, thereby improving diagnostic accuracy and treatment planning. Further research with larger, multicenter cohorts is recommended to validate these findings.

In this review we explore the recent progress in catalytic materials for ammonia synthesis that are based on metal nitrides and other catalytic surfaces. It comprises a detailed overlook of various techniques used in ammonia synthesis research and the state-of-the-art modeling techniques employed to investigate new reaction mechanisms and more efficient processes for sustainable ammonia synthesis production. The review is discussed in the context of reaction mechanisms developed and recent progress that has been made with respect to thermal, electrochemical and photocatalytic ammonia synthesis.

High mountain rainforests are vital in the global energy and carbon cycle. Understanding the exchange of energy and carbon plays an important role to reflect responses to climate change. In this study, an eddy-covariance (EC) measurement system installed in the high Andean Mountains of South Ecuador was used. As EC measurements are affected by heterogeneous topography and vegetation height, the main objective was to estimate the effect of the sloped terrain and the forest on the turbulent energy and carbon fluxes considering the energy balance closure (EBC) and the heat storage. The results showed that the performance of the EBC was generally good and estimated to be 79.5%. This could be improved when the heat storage effect was considered. Based on the variability of the residuals in the diel modifications in the imbalances were highlighted. Particularly, during daytime residuals were largest (56.9 W/m² on average) with a clear overestimation. At nighttime mean imbalances were rather weak (6.5 W/m²) and mostly positive, while strongest underestimations developed in the transition period to morning hours (down to -100 W/m²). With respect to the Monin-Obukhov stability parameter ((z-d)/L) and the friction velocity (u*) it was revealed that largest overestimations evolved in weak unstable and very stable conditions associated with large u* values. In contrast, underestimation was related to very unstable conditions. The estimated carbon fluxes were independently modelled with a non-linear regression using a light-response relationship and reached a good performance (R²=0.52). All fluxes were additionally examined in the annual course to estimate whether both, energy and carbon fluxes, resembled the microclimatological conditions of the study site. This unique study demonstrated that EC measurements provide valuable insights into land surface -atmosphere interactions and contribute to our understanding of energy and carbon exchanges. Moreover, the flux data provide an important basis to validate coupled atmosphere ecosystem models.

This study examines the effects of working capital management strategies on firm’s financial performance of Indian cement companies using 11-year (2010-2020) financial data of 31 companies listed in Bombay Stock Exchange. It is intended to find out whether the strategies made by finance managers with respect to the components of working capital such as average receivable period, inventory conversion period, average payment period and cash conversion cycle, etc. affects the firm’s performances individually and in total. The results of Pearson’s correlation coefficient and random effect regression model shows that there exists a negative relationship between financial performance measured in terms of return on assets (ROA) and inventory turnover period (ITP) as well as accounts payable period (APP), whereas firm’s performance is not significantly affected by accounts receivable period (ARP) and cash conversion cycle (CCC). Similarly, it has been observed that the liquidity measures such as current ratio (CR) and quick ratio (QR) have a significant positive association with ROA. Moreover, the size of the firms and leverage are inversely related to ROA but the age of the firms is not significantly affecting their financial performances. Hence, it can be concluded that how an organisation designs its working capital strategy do have an impact on its performances.

Metal additive manufacturing (AM) has gained much attentions in recent years due to its advantages including geometric freedom and design complexity, appropriate to a wide range of potential industrial applications. However, conventional metal AM methods have high-cost barriers due to the initial cost of the capital equipment, support and maintenance, etc. This study presents a unique low-cost metal material extrusion (MME) technology. The filaments used have polylactic acid (PLA) as the matrix and metal powders (copper, bronze, stainless steel, high carbon iron, and aluminum) as reinforcements. Using the proposed fabrication technology, test specimens were built by extruding polymer/metal composite filaments, which were then sintered in an open-air furnace to produce solid metallic parts. In this research, the mechanical and thermal properties of the built parts are examined using tensile tests, thermogravimetric-, thermomechanical- and microstructural analysis.

Peptides, both natural and synthetic, are well suited for a wide range of purposes and offer versa-tile applications in different fields such as biocatalysts, injectable hydrogels, tumor treatment, and drug delivery. The rising prominence of therapeutic peptides encompasses anticancer, antiviral, antimicrobial, and anti-neurodegenerative properties. The metals Na, K, Mg, Ca, Fe, Mn, Co, Cu, Zn, and Mo are ten of the twenty elements that are considered essential for life. Crucial for under-standing the biological role of metals is the exploration of metal-bound proteins and peptides. Aside from essential metals, there are other, non-essential metals that also interact biologically, exhibiting either therapeutic or toxic effects. Irregularities in metal binding contribute to diseases like Alzheimer’s, neurodegenerative disorders, Wilson's, and Menkes disease. Certain metal com-plexes have potential applications as radiopharmaceuticals. The examination of these complexes was done by preforming UV-Vis, IR, EPR, NMR spectroscopy, and X-ray analysis.

Numerous studies have been conducted in past so as to understand whether the working capital management policies of an organisation affect its performance or not. Some studies have found a positive relationship between WCM and firm performance. However, other studies have found a negative impact of WCM on firm performance. Present research work is an endeavour in this direction to find out the working capital management policies and strategies of Indian cement companies and their performances. The study employs a quantitative approach to examine whether the Indian cement companies optimally use their working capital, which is analysed by establishing the relationship between the working capital management and profitability using 11-year (2010-2021) financial data of 31 cement companies listed in Bombay Stock Exchange (BSE). The findings of the random-effects model say that only ITP is significantly negatively related to the ROA of the cement companies at a 0.01 level of significance. Similarly, APP also negatively yet poorly predicts ROA at a 0.10 level of significance the firm’s profitability is not significantly affected by ARP and CCC. Also, it has been observed that the liquidity measures CR and QR have a significant positive association with ROA. Further, the size of the industries and leverage are inversely related to ROA but the age of the firm is not significantly predicting their financial performance.

Flexibility is perceived as a primary reason for working as a gig worker. However, there are not enough studies that investigate gig workers' motivations. Hence, this study aims to examine the motivation of white-collar gig workers using a sample size of 327 gig workers in Mongolia, a developing country’s labor market. The purpose of this study is to investigate intrinsic and extrinsic motivation factors for white-collar gig workers and their impact on behavioral intentions such as those of remote workers, freelancers, and any representatives of digital gig workers, not location-based gig workers. The primary data used in this study were collected through questionnaires from an online platform that attracts white-collar gig workers. The characteristics of this group are analyzed using Smart PLS4.0 software through the PLS-SEM technique to test the hypothesized relationships. Overall, the study contributes to an extension of current literature by understanding the white-collar digital gig workforce’s motivations and reasons behind it.

This study evaluates literature on the wheel of audit partners in Chinese companies and institutions by examining the impact of relationships before and after the rotation between the input and output partners. We consider the partners in the rotation before the rotation, before the work relationship. We find two different results from the previous working relationships: (a) increasing the likelihood of the outgoing partners after the cooling period, and (b) reducing the quality of the audit and lower accounting after the rotation. These findings ask whether the rotational partners are truly independent of the working relationships.

A dynamic impact test was performed on as-rolled AZ31 alloy with gradient microstructure under various strains. The microstructural evolution and mechanical properties were systematically investigated. As the strain rate gradually increases, an increasing number of twins are formed, facilitating dynamic recrystallization (DRX), and the mechanical properties are also gradually improved as well. The microstructure becomes heterogeneous at higher strain rates, but the peak stress decreases. The impact process results in significantly higher performance due to microstructural refinement, work hardening by dislocations and precipitates. In addition, both the adiabatic shear band and the adjacent crack experience a temperature rise that exceeds the recrystallization temperature of the alloy. This observation also explains the presence of ultrafine recrystallized grains within the adiabatic shear band and the appearance of molten metal around the crack.

Building on the job demands-resources (JD-R) and the allostatic load (AL) models, in this study we investigated the role of smart working (SW) in the longitudinal association between workload/job autonomy (JA) and a possible biomarker of work-related stress (WRS) in the hair, namely the cortisol to dehydroepiandrosterone sulphate (DHEA(S)) ratio, during the COVID-19 pandemic. Overall, 124 workers completed a self-report questionnaire (i.e., psychological data) at Time 1 (T1) and collected a strand of hair (i.e., biological data) three months later (Time 2, T2). Results from moderated multiple regression analysis showed that smart working at T1 was negatively associated with hair cortisol/DHEA(S) ratio at T2. Additionally, the interaction between workload and SW was significant, with workload at T1 being positively associated with hair cortisol/DHEA(S) ratio at T2 among smart workers. Overall, this study indicates that SW can be conceived as a double-edged sword, with both positive and negative consequences on employee well-being. Furthermore, our findings suggest that hair cortisol/DHEA(S) ratio is a promising biomarker of WRS. Practical implications that organizations and practitioners can adopt to promote organizational well-being are discussed.

This investigation mainly focused on the microstructural analysis of Al based hybrid metal matrix composites. Aluminium as base metal and reinforced with 2% B4 C, ZrO2 (2%,4%,6%), SiC (4%,8%,12%). Specimens were manufactured by using conventional stir casting technique. Hybrid metal matrix composites were examined by using Scanning electron microscope. This research explained XRD, EDS and Fractography analysis. This investigation shows the reinforced material has given better results in all aspects than pure Al6061 alloy and homogeneous dispersion of particles inside the matrix. Porosity, delamination, cracks, particle distributions were observed through microstructural analysis. Additionally determined the crystal size of pure Aluminium 6061 alloy and hybrid composites.

Background: Mules are used worldwide for agrarian purposes such as plowing and harvesting crops. In this study, mules were used for plowing and cultivation. While mules are believed to be less susceptible to diseases and fatigue than horses, no scientific investigation has been conducted to support this belief. The objective was to assess effect of work-associated fatigue on hematological and biochemical parameters in working mules in Mexico. Methodology: Six healthy mules 6.5 to 23 years, 3.5 BCS, were studied. Three blood samples/day were taken at the beginning and end of the work season. One sample taken at the beginning of the day, middle, and end (3 hours apart). Biochemical parameters, including the concentrations of albumin, globulin, total protein, glucose, alkaline phosphatase (ALP), aspartate aminotransferase (AST), gamma-glutamyl transferase (GGT), total bilirubin, lactate, creatinine kinase (CK), urea, creatinine, calcium, sodium, potassium, total carbon dioxide (tCO2), and al-bumin-to-globulin ratio, were determined using the veterinary Skyla-VB1 automated analyzer (Lite-On Technology Corporation, Hsinchu-Taiwan), and blood lactate concentration using the handheld Lactate Scout Vet. Results: Significant increases in concentrations AST (P < 0.001), BUN (P < 0.001), calcium (P = 0.002), creatine phosphokinase CPK U/L (P < 0.001), tCO2 (P = 0.006), and urea (P < 0.01), were observed at the end of the work season. However, sodium, potassium, and chloride were significantly decreased at the end of the work season. No treatment or time-by-treatment interaction effect was observed for ALP, creatinine, globulin, or the albu-min-to-globulin ratio. Conclusions: The significant decrease in mineral and electrolytes (Na, K, and Cl) at the end of work season could suggest change in electrolytic balance during the strenuous plowing season. A higher concentration of tCO2 at end of the season is a good indicator of metabolic acid-base disturbances. Results indicate use of mules for plowing fields disrupts the mules' micromineral and electrolyte profiles. Increased CPK levels demonstrate that the workload was excessive. This study furthers our understanding of biochemical responses in mules.

Background: The rise of cloud computing has led to the increasing number of organizations that rely on it for various tasks and services, such as education, healthcare, and e-commerce. Unfortunately, many security threats can be caused by the sudden use of cloud platforms. Objective: This paper aims to provide a comprehensive overview of these threats and how they can be mitigated. Many companies are moving toward cloud computing to sustain their business growth and provide their employees with the best possible work environment. Results: Due to the rise of cyber security threats and the unprecedented number of breaches of data, small and medium-sized enterprises are also starting to take a huge leap. The outbreak of COVID-19 has affected the lives of people all around the world. Conclusion: Due to the seriousness of the situation, the WHO has declared the COVID-19 pandemic a public health emergency. To minimize the spread of the virus, the entire world has started adopting social distancing

Improving the quality and access to healthcare services in rural areas is fundamental to develop sustainable healthcare systems. This research aims to explore the motivations of healthcare professionals to work and settle in rural island areas of Greece with limited access to secondary and tertiary care. The study suggests practical ways to encourage self-motivation and attract more health workers in rural areas. An exploratory qualitative research approach was employed, involving semi-structured interviews with 16 healthcare professionals working in primary care units that lack direct hospital or hospital-health center access. The research was conducted specifically in the rural islands of Cyclades. Thematic analysis was conducted to identify common themes and unique insights from the participants. The analysis revealed three thematic categories. Τhe «attraction» thematic was influenced by personal factors, random selection, origin, accommodation factors, professional factors and obligatoriness. The «recruitment» thematic was associated with understaffing, special care issues, unstable working environment, educational and organizational aspects, and insular lifestyle. The thematic of «retention» highlighted personal issues, accommodation difficulties, economic and work-related issues, and unique challenges posed by an insular lifestyle. This research provides valuable insights into the motivations that drive healthcare professionals to settle, work, and remain in remote island units, as well as the challenges they encounter in making this decision. The study proposes strategies to motivate and attract more healthcare professionals to rural areas. These findings should be considered when formulating or reviewing primary healthcare empowerment policies to ensure equitable healthcare access for all individuals.

Direct Energy Deposition (DED) is a versatile and efficient method in metal additive manufacturing. However, humping, caused by abnormal dynamics in the melt pool (MP), poses a significant threat to the geometric integrity of manufactured products. Current state-of-the-art (SOTA) methods primarily detect humping by analyzing late-stage spatial abnormalities, such as MP detachment. This approach is fundamentally reactive, leading to a tendency to miss early humping spatiotemporal dynamics, like cyclic elongation of the MP. This study introduces a novel, proactive indicator named VIMPS (Variability of Instantaneous MP Solidification-Front Speed), a physics-based tool designed to quantify early abnormal fluctuations in MP solidification speed. The experiments demonstrate VIMPS correlation with humping-induced geometric inaccuracies. By capturing early spatiotemporal dynamics of the MP, VIMPS reduces detection latency by 30 seconds compared to existing SOTAs that focus solely on spatial abnormalities. This significant improvement transforms detection from reactive to proactive, providing the time needed for corrective actions to enhance the overall productivity and quality of the DED process.

As high strength and ultra-high strength steels are widely used in all kinds of modern welded constructions, a lot of research is carried out to investigate the mechanical properties of weldments of these steels but there is a scarce information on such important characteristic as their corrosion behaviour. This research focuses on the corrosion behaviour of weld metal of weldments of S906QL and S700MC steels. Weld metal was tested electrochemically in a 3,5% NaCl aqueous solution via potentiodynamic scan to determine corrosion rate and its dependence on welding gap. No influence of welding gap on corrosion rate was found but the experimental results suggested that corrosion rate depended on the chemical composition of filler material and the microstructure of weld metal.

The bioindicator potential of seagrass ecosystems in coastal trace metal monitoring is low for tropical island ecosystems. This study evaluated the bioindicator potential of six seagrass species exposed to anthropogenic trace metal pollution in the Andaman and Nicobar Islands (ANI) of India. Sediment and seagrass biomass, samples were analyzed for trace metals (Co, Cr, Cu, Fe, Mg, Mn, Ni, Pb, Zn) from four locations of ANI exposed to anthropogenic contamination. Geo accumulation Index values indicated moderate trace metal contamination in seagrass sediment. Seagrass trace metal accumulation from sediment was both species-specific and location- specific for ANI. Small seagrass species such as H. ovalis, H. beccarii and H. uninervis accumulated the maximum concentration of six trace metals (Cr, Cu, Fe, Ni, Pb, Zn) in their tissues compared to big seagrass species like T. hemprichii and E. acoroides of ANI. This study indicates leaves of small seagrass and roots of big seagrass species can serve as short- and long-term bioindicators respectively, of coastal trace metal contamination in tropical islands of ANI.

Titanium-based metal-matrix composites manufactured by additive manufacturing offer tremendous lightweighting opportunities. However, processing high reinforcement content remains challenging. This study reports an improved manufacturing process for Ti-TiC enabling high reinforcement content and significant fracture strain concurrently: mechanical blending, followed by laser powder bed fusion and a single heat treatment. As-built microstructure shows both un-melted TiC particles and sub-stoichiometric TiC dendrites resulting from a partial dissolution of TiC particles. The heat treatment is shown to fully convert TiC dendrites into equiaxed TiC grains. Reduction of the C/Ti ratio in TiC during the process results in an increase in the reinforcement content, from a nominal 12 vol% to an effective 21.5 vol%. Ti-TiC tensile samples reached fracture strains of up to 1.7%, Young’s moduli of up to 149 GPa and ultimate tensile strengths of up to 827 MPa. Lower TiC initial powder size distributions displayed the best mechanical performance.

Background: Young people with intellectual developmental disabilities have a persistent delay in the development of executive functions. Virtual reality (VR) is increasingly being used as a cognitive intervention tool, with significant effectiveness demonstrated in different types of populations. Methods: This pilot study aims to investigate the impact of a cognitive training program utilizing VR on young adults diagnosed with intellectual developmental disability (IDD). The participants (N=15) served as their own control group and were assessed three times: weeks 0, 8 and 16, with a rest period (0-8 weeks) and an intervention period (8-16 weeks). The assessments included measures of cognitive function, provided by E-Prime®. Results: Overall, an improvement in working memory and inhibitory control was found after the intervention, but not in sustained attention. Conclusions: These findings suggest that VR-based cognitive training holds promise as an effective intervention for enhancing cognitive abilities in young adults with intellectual developmental disability.

Children’s health, development and education cannot be handled separated; they form one process and are profoundly interrelated. This article considers how to ensure children’s physical and mental fitness for school and maintain it once they are there. Rwanda Is a case study of health and development issues which render children unreceptive to education. This is not news to Rwanda’s government, but until recently the donor community was not interested in supporting implementation. The story of Rwanda illustrates the need to think about changes of policy and practice in their context of structures and culture – how they interact and how they are facilitated or constrained by structures and by cultural understandings. To grasp what is going on and for successful implementation of policy, it is necessary to look at situations as a whole and consider human and governmental agency as real influences rather than just consequences of causal mechanisms.

Sustainable soil quality management is one of the most important approaches in ensuring high agricultural productivity and safe quality produce. With the current rising application of inorganic fertilizers and chemical pesticides, degradation of agricultural soils is becoming a global phenomenon, attracting attention of many researchers. The present study hypothesized that with the increasing chemical pesticide and fertilizer application under various cropping systems, there is potential for increased toxicity of heavy metals residues above background concentrations and their associated complexes and intermedia transfer between environmental compartments in large-scale farms in Kenya. Using standard methods, 204 soil samples collected from five distinct cropping systems were analyzed for PH, Electrical Conductivity, exchangeable base cations (Na+, Mg2+, K+, Ca2+), Cu, Pb, Zn, Cd, Fe, Cr, Total Organic Carbon and Total N and data analyzed using Genstart, version 23.1. The concentrations of Zn, Cu, Pb and Fe were lower than the globally acceptable levels hence less soil pollution threat (NPI&lt;1). However, Cd concentration exceeded permitted levels (NPI&gt;1). Among the cropping systems considered, Maize and sugarcane cropping systems were the most susceptible to heavy metal pollution. In conclusion, the rank order of the pollution potential associated with heavy metal contamination in the study area is Cd&gt;Zn&gt;Pb&gt;Cu&gt;Cr&gt;Fe.

In the realm of metal steel and iron manufacturing, there is a constant drive to optimize production efficiency and enhance the quality of the final products. This abstract explores a paradigm shift in this industry through the utilization of Computational Fluid Dynamics (CFD) as a powerful tool for achieving these goals .The study focuses on various critical aspects of the manufacturing process. Firstly, it delves into three-phase processes such as slag and gas entrainment in liquid steel, which have a significant impact on the overall product quality. Understanding and optimizing these processes is crucial to ensure the desired chemical composition and physical properties of the final metal.The abstract investigates the role of CFD in vacuum degassing, a process that plays a pivotal role in removing impurities, such as hydrogen and oxygen, from the liquid steel. By leveraging CFD to simulate and analyze the fluid flow patterns, researchers and engineers can design more efficient vacuum degassing systems, leading to improved product purity and reduced waste.Another crucial aspect explored in this abstract is the alloy melt and mixing process. By employing CFD simulations, researchers can gain insights into the movement of different alloy components and optimize their distribution within the melt. This aids in achieving the desired alloy composition, ensuring uniformity, and enhancing the mechanical properties of the final product.In addition, the study delves into the movement and flotation of inclusions, which are unwanted impurities present in the metal. CFD can be utilized to model and analyze the behavior of these inclusions, enabling engineers to design efficient strategies for their removal, thereby enhancing the purity and integrity of the final product.Moreover, the abstract considers the impact of melt temperature losses, which can occur during different stages of the manufacturing process. By employing CFD, it becomes possible to understand and mitigate these temperature losses, leading to improved energy efficiency and better control over the manufacturing parameters.Part 1 of this abstract critically evaluates the use of CFD in iron making, analyzing its benefits and limitations. It highlights how CFD can aid in process optimization, improving the understanding of complex phenomena involved in iron making, and ultimately leading to enhanced production efficiency.Part 2 focuses on the application of CFD in steel making and steel operation. It explores the fluid flow dynamics during different stages of steel production, including refining, casting, and rolling. By leveraging CFD, engineers can optimize these processes, leading to improved product quality, reduced defects, and increased productivity.This abstract demonstrates the transformative potential of Computational Fluid Dynamics in metal, steel, and iron manufacturing. By utilizing CFD as a tool to model and analyze complex fluid flow phenomena, researchers and engineers can revolutionize the production process, maximizing efficiency, and ensuring high-quality end products.

The purpose of this study was to analyze the cross-linguistic influence of previously learned languages and working memory capacities on the vocabulary performance of two different typological languages. The objectives of this study were (1) to compare the working memory capacities of bilingual adults in relation to the vocabulary performance of two different languages never learned by the participants, and (2) to analyze to what extent the typology of previously learned languages influences working memory capaci-ties in relation to the vocabulary performance of French and Nahuatl. A group of 43 Mexican-Spanish college students participated in this experimental study. The participants completed a series of working memory tasks in Nahuatl and French. The results showed that working memory capacities were lower in Nahuatl than in French. Thus, a correlation was found between their first and second language and vo-cabulary performance in French. We can consider the influence of previously learned languages as a significant factor in vocabulary acquisition in accordance with the participants' working memory capacities.

The application of movement-detection sensors is crucial for understanding surface movement and tectonic activities. The development of modern sensors has been instrumental in earthquake monitoring, prediction, early warning, emergency commanding and communication, search and rescue, and life detection. There are numerous sensors currently being utilized in earthquake engineering and science. It is essential to review their mechanisms and working principles thoroughly. Hence, we have attempted to review the development and application of these sensors by classifying them based on the timeline of earthquakes, physical or chemical mechanisms of sensors, and location of sensor platforms. In this study, we analyzed all available sensor platforms that have been widely used in recent years, with satellites and UAVs being among the most used. The findings of our study will be useful for future earthquake response and relief efforts, as well as research aimed at reducing earthquake disaster risks.

Recent research efforts in bone tissue engineering have been primarily directed towards manufacture-viable synthesis of biomaterials that can significantly enhance the biocompatibilities and osteogenic capabilities on the new biomaterials. This paper presents a straightforward, cost-effective, optimized, and well-controlled hydrothermal synthesis of Nb-doped potassium titanate nanofibers in high-purity. Characterization data revealed that the Nb-doping potassium titanate maintained the crystal structure, showing great promise for applications in bone tissue engineering.

Coating a suitable material on substrate in thickness of nano to micro metres is a great interest for the scientific community. Hard coatings develop under the significant composition of suitable gaseous and solid atoms, where their energy and forced behaviors under certain transition states favour the binding. In the binding mechanism of gaseous and solid atoms, electron belonging to outer ring (filled state) of gaseous atom undertakes another clamp of energy knot belonging to outer ring (unfilled state) of solid atom. The set process conditions develop the coating of gaseous and solid atoms when energy of non-conservation is involved. Different natured atoms develop the structure in the form of hard coating by locating a common ground point, which is in their central ground points. Here, gaseous atoms increase the potential energy of electrons by decreasing levitational force (at electron level) in a controlled orientating manner, whereas solid atoms decrease the potential energy of electrons by decreasing gravitational force (at electron level) in a controlled orientating manner. Thus, hard coating is deposited under the oppositely switched energy and forced behaviors of different natured atoms. In TiN coating, Ti–Ti atoms bind due to the difference of expansion in their lattices when one atom is deposited and one is being deposited. So, one Ti atom just lands on the already landed Ti atom. While adhering N atom to Ti atom, it occupies the interstitial position in the Ti atoms. The rate of ejecting solid atoms depends on the type of source, parameters and a processing technique. In random arc-based vapor deposition system, depositing coating at substrate depends on several parameters. As per set conditions of the process, different natured atoms deposit at substrate surface to develop the structure of coating. In addition to intrinsic behavior of atoms, different properties of coatings materialised as per the nature of forces engaged under the involved energy. In developing hard coating of gaseous and solid atoms, an involved energy of non-conservation engages force of non-conservation, too. Hence, this study opens new avenues not only in the fields of hard coatings but also in the fields of functional coatings, medical and surgical implant coatings, protective and sensitive coatings, etc.

We show the enhancement in the intensity and emission rate of perovskite cesium lead bromide (CsPbBr3) and formamidinium lead bromide (FAPbBr3) nanocrystals in the presence of single and double gold layer cavities, which we refer to as Metal-Emitter (ME) and Metal-Emitter-Metal (MEM) nanostructures. Up to 1.9-fold photoluminescence intensity and up to 5.4-fold emission rate enhancements were obtained for FAPbBr3 nanocrystals confined by double gold layers, which are attributed to plasmonic confinement from the gold layers. The experimentally obtained values are validated by analytical calculations and electromagnetic simulations. Such an effective method of manipulation of the spontaneous emission rate by simple plasmonic nanostructures can be utilized in sensing and detection applications.

Drosophila melanogaster serves as a important research model both for genetic investigations and for the study of metal toxicity, facilitating the elucidation of physiological mechanisms comparable to those of human organisms. In our research, we evaluated the toxicity effect resulting from exposure to various concentrations of lead and copper on the prolificity rates throughout the life cycle (egg-adult) of four genotypes of Drosophila melanogaster: wild-type (control), white, brown, and white-vestigial. During our study, the prolificity rates were examined across three repetitions under the impact of exposure to concentrations of 0.50, 1.00, 2.00, and 4.00 mM of copper (CuSO₄) and lead (Pb(C₂H₃O₂₎₂). Prolificity rates throughout the life cycle exhibited variations as a direct consequence of genetic factors, the concentration of exposure, and the specific type of metal, either copper or lead. The mutant white-vestigial genotype revealed an IC₅₀ concentration for prolificity inhibition at lower doses of 2.00 mM for copper and 4.00 mM for lead, in contrast to the control genotype (wild-type), which exhibited an inhibition concentration rate >IC₅₀ of 4.00 mM only in the case of copper. Our results concluded that the (i) dose influences the prolificity rate in a directly proportional manner, (ii) comparative analyses between copper and lead revealed that copper displayed toxicity across all genotypes within the concentration range of 0.50 mM to 2.00 mM. In contrast, lead exhibited toxicity within the concentration range of 1.00 mM to 4.00 mM, highlighting a (iii) more acute toxicity characteristic in the case of copper. Thus, the results of this research reflect the importance of using Drosophila melanogaster as a genetic model in the comparative study of the interaction between genetic factors and the toxicity of metals, offering significant insights into monitoring their impact and defining the maximum permissible doses on organisms.

Metal additive manufacturing (AM), commonly referred to as 3D printing with metals, is an innovative technology with significant potential to transform industries such as aerospace, automotive, and healthcare. Despite its promise, the field faces several challenges that impact both its technical feasibility and economic viability. This paper explores the primary technical challenges, including material properties and processing complexities, such as the need for precise control of thermal gradients and the mitigation of defects like porosity and residual stresses. Additionally, it addresses the economic barriers, including high initial equipment costs, the need for specialized knowledge, and the relatively slow build speeds compared to traditional manufacturing methods. By examining these challenges, this paper aims to provide a comprehensive overview of the current state of metal additive manufacturing and suggest potential pathways for overcoming these obstacles to facilitate wider adoption and technological advancement in the field.

The band gap research in graphene is still a very important topic for materials application. Here, we report a band gap opening and p-type semiconducting property of the graphene by using an electrochemical doping on graphene surface. The manganese-oxide nanopar-ticles adsorbed on the graphene were used as the dopants in an electrolyte, which induce the band gap opening and the change of electronic structure. In addition, the fabricated graphene FET shows the p-type semiconductor behaviors. The temperature dependent conductivity of the p-type doped graphene at applied potential of 1.5 V during electro-chemical doping shows the formation of band gap of 0.23 eV, which is obtained from the fitting of conductivity equation. The semiconducting properties of manganese-oxide doped graphene is attributed to the formation of manganese-oxide nanoparticle on the surface of graphene.

Brazilian garimpeiros are a highly hard-to-reach and mobile population, with little access to basic hygiene and health services, and have been crossing the border to work irregularly in gold mines in French Guiana since the 90s. This study aimed to characterize this population and identify their main health problems. A cross-sectional study was carried out in the municipality of Oiapoque-AP, with two surveys: before (2018) and after (2019) the implementation of Malakit. Individuals were recruited from resting places and submitted to a questionnaire with demographic variables, history and knowledge of malaria, and health issues in the mines. Simultaneously, a clinical evaluation was performed. The garimpeiros were mainly men from Maranhão, Pará, and Amapá, with a low educational level and worked on average for 10 years in the mining sites. The study population mentioned numerous health problems: malaria, followed by leishmaniasis, flu, body aches, headaches, and digestive problems. Other diseases mentioned were skin diseases, bat bites, hepatitis, and HIV infection. This vulnerable population is constantly subjected to heavy routines and exposed to different diseases and infections that can spread across borders. Knowledge of this is essential for developing public health policies that can be integrated into specific epidemiological situations.

Abstract: Social media has become a vital tool in ensuring productivity among Undergraduates, as studies have shown an increased number of users globally. This study assessed the impact of social media usage on undergraduates’ academic performance and working memory. Participants from three different universities such as the University of Georgia (UG), Eastern European University (EEU), and Batumi State University (BSU) completed this study using online google forms. UG and EEU are in the capital city, and BSU is in Batumi City. The study questionnaires were approved by the institutional review board before the data collection. Descriptive analyses were assessed for all study populations, characteristics, frequencies, percentages, means, and standard deviations using Statistical Package for Social Science (SPSS Inc., Chicago, IL, version 25.0 for Windows) software. 41.3% were male students, as most of the participants were foreign students living and studying in Georgia. Male students had the risk of ‘conflict’ with families and friends because of social media. Female students are at increased risk of using social media as an ‘escape’ from negative feelings. 89.7% of students that perform physical activities, considering their academic workload had the risk of preoccupation complaints. 87.9% felt dissatisfied regularly because they wanted to spend more time on social media. Utilization of social media differed based on the characteristics of the participants such as age, gender, and geography. We observed the increase in prevalence of social media addiction, its effect on academic performance and working memory among undergraduate students.

This study outlines a 3-step production process for Ti-TiC Metal Matrix Composite (MMC) employing powder Mechanical Blending, Laser Powder Bed Fusion (LPBF), and a heat treatment. A TiC fraction of more than 20 vol% was formed in-situ through the reaction of titanium with carbon during the LPBF process. The manufactured MMC pieces showed a record stiffness and fracture strain combination. The LPBF energy density impacted strongly porosity type. The as-built microstructure displayed an homogeneous distribution of sub-stoichiometric TiC dendrites which were fully converted into equiaxed TiC grains during the heat treatment. The TiC C/Ti ratio was found to be close to 0.5, resulting in an effective reinforcement content nearly twice the one expected for stoichiometric TiC, leading to stronger reinforcement. The mechanical analysis revealed a Young’s modulus of up to 149 GPa and an ultimate tensile strength of up to 770 MPa, indicating a 27% and 34% improvement, respectively, compared to commercially pure Titanium produced by LPBF and heat treated in the same conditions. A fracture strain of up to 2.8% was achieved. The combination of in-situ formation of defect-free TiC reinforcement and subsequent heat treatment enables to reach an exceptional ductility, considering the 20 vol% reinforcement content.

Two-dimensional (2D) transition metal dichalcogenides (TMDCs) nanosheets have shown extensive applications due to their excellent physical and chemical properties. However, the low light absorption efficiency limits their application in optoelectronics. By rolling up 2D TMDCs nanosheets, the one-dimensional (1D) TMDCs nanoscrolls are formed with spiral tubular structure, tunable interlayer spacing and opening ends. Due to their increased thickness of scroll structure, the light absorption is enhanced. Meanwhile, the rapid electron transportation is confined along the 1D structure. Therefore, the TMDCs nanoscrolls show improved optoelectronic performance compared to 2D nanosheets. In addition, the high specific surface area and active edge site from bending strain of basal plane make them promising materials for catalytic reaction. Thus, the TMDCs nanoscrolls have attracted intensive attention in recent years. In this review, the structure of TMDCs nanoscrolls is firstly demonstrated and followed by various preparation methods of the TMDCs nanoscrolls. Afterwards, the applications of TMDCs nanoscrolls in the fields of photodetection, hydrogen evolution reaction, and gas sensing are discussed.

Background: The work and life of a junior doctor has changed dramatically over the past 50 years. Descriptions of historic working conditions are usually anecdotal and tinted with nostalgia. But presented with the facts, do heath care professionals feel working conditions things have improved or declined in the last 50 years? Methods: An interview was conducted with a retired surgeon who, in 1970, worked as a house surgeon (Foundation Year 2, FY2 equivalent) at a regional burns service. This was compared with a review of available literature to assess objectively working conditions in that period. The information generated from this produced a poster summarizing the key differences over a 53-year timeframe. This information was presented to the current medical work force and a survey was conducted to determine their preference. Statistical analysis including binary logistic regression was performed. Results: The questionnaire was completed by 76 respondent healthcare workers of mixed grades and backgrounds. The majority of respondents (64%) would choose to work in today’s burns unit. The age of the respondent was the best predictor for preference of working conditions (p = 0.043). Conclusions: Multiple changes in the working conditions were identified. The majority of respondents consider today’s working conditions to be better than that of the past. However, more senior clinicians were more likely to prefer the conditions of 1970 to present day, suggesting a generational shift in opinion.

(1) Background: Many processes play a key role in how language functions, and these processes are strongly related to reading. The aim of our research was to explore the relationship between reading impairment associated with adult acquired cognitive-linguistic impairment (aphasia) and the components of verbal working memory involved in language functioning. (2) Methods: We measured the reading abilities of a total of twenty-two adults diagnosed with aphasia using the Adult Acquired Reading Assessment. To assess working memory, we applied the measurement procedures available in Hungarian for measuring verbal working memory. Correlation analyses were performed to investigate the relationship between reading and the components of working memory involved in processing verbal information. In order to explore this relationship as comprehensively as possible, the results were analysed quantitatively through group-level analyses and qualitatively through case studies. (3) Results: The results suggest that the functioning of phonological short-term memory and verbal working memory is crucial for the reading of vowels, for certain word reading sub-processes such as reading complex words and pseudowords, and for text comprehension tasks, in particular for the processing of implicit text-level infor-mation. (4) Conclusions: The data support a strong relationship between reading and working memory, but not all mechanisms are related with the same weighting. The data will contribute to the understanding of the relationship between reading and working memory, which is important in order to see which cognitive components are dominant in reading instruction and which other cognitive mechanisms are affected in poor readers.

Concussion, also known as mild traumatic brain injury (mTBI), commonly causes transient neurocognitive symptoms, but in some cases, it causes cognitive impairment, including working memory (WM) deficit, which can be long-lasting and impede a patient’s return to work. The predictors of long-term cognitive outcomes following mTBI remain unclear because abnormality is often absent in structural imaging findings. The purpose of the study was to determine whether machine learning-based models using functional magnetic resonance imaging (fMRI) biomarkers and demographic or neuropsychological measures at baseline could effectively predict 1-year cognitive outcomes of concussion. We conducted a prospective, observational study of patients with mTBI who were compared with demographically-matched healthy controls enrolled between September 2015 to August 2020. Baseline assessments were collected within the first week of injury, and follow-ups were conducted at 6 weeks, 3 months, 6 months, and 1 year. Potential demographic, neuropsychological, and fMRI features were selected according to the significance of correlation with the estimated changes in WM ability. The support vector machine classifier was trained using these potential features and estimated changes in WM between the predefined time periods. Patients demonstrated significant cognitive recovery at the third month, followed by worsened performance after 6 months, which persisted until 1 year after concussion. Approximately half of the patients experienced prolonged cognitive impairment at 1-year follow up. Satisfactory predictions were achieved for patients whose WM function did not recover at 3 months (accuracy=87.5%), 6 months (accuracy=83.3%), 1 year (accuracy=83.3%), and performed worse at 1-year follow-up compared to baseline assessment (accuracy=83.3%). This study demonstrated the feasibility of personalized prediction for long-term postconcussive WM outcomes based on baseline fMRI and demographic features, opening a new avenue for early rehabilitation intervention in selected individuals with possible poor long-term cognitive outcomes.

This study has been taken during COVID-19. It describes the working scenario of all class of peoples and their mental anxieties are analysed based on their psychological behaviour patterns.

The growing threat of antibiotic pollution in water systems demands innovative and sustainable remediation strategies. Nanocellulose-based magnetic metal-organic frameworks (MOFs) represent a cutting-edge solution for the adsorption and removal of antibiotics, leveraging their high porosity, magnetic properties, and environmentally friendly nature. This paper provides an in-depth review of recent advancements in nanocellulose-based MOFs, focusing on their synthesis, adsorption mechanisms, and applications in environmental remediation between 2020 and 2024. By summarizing key studies, we highlight their performance in targeting widely used antibiotics such as tetracyclines and fluoroquinolones. The integration of nanocellulose with MOFs not only enhances adsorption capacity but also offers easy recovery, recyclability, and environmental compatibility. This review explores their adsorption mechanisms, practical applications, and future research directions, contributing to the advancement of scalable and sustainable water treatment technologies.

Electromobility promises to efficiently mitigate consequences of increasing traffic volume and its accompanied greenhouse gas emissions. On an individual level, electrified bikes allow emission free electrified mobility at moderate costs and consequently their stock has increased significantly in recent years. This simultaneously increases the demand for spare parts, which are often manufacturer or application-specific, and due to many variants, challenging to provide for the market. This article evaluates powder-based and extrusion-based metal additive manufacturing of a typical electrified bike component to demonstrate an alternative spare parts supply. The investigation demonstrates how these parts can be additively manufactured function equivalent and with sufficient mechanical properties, also taking economical aspects into account. Furthermore, the needed resources and related environmental consequences for metal-based additive manufacturing spare-part production are compared for both process routes. The results show that both routes are capable of producing spare-parts at comparatively same mechanical performance and resource costs, while needed resources such as energy, gases and manufacturing time are significantly lower for powder-based, respectively machine costs for extrusion-based additive manufacturing. Therefore, additive manufacturing offers a promising opportunity to produce parts in small quantities resource efficient and rapidly.

Previous literature has linked working for pay while attending university with negative academic and health outcomes, yet working students are often resilient when experiencing such adverse circumstances. This makes it crucial to explore potential psychological mechanisms which transform adverse experiences into sources of motivation and persistence for working students. We explore one mechanism – social identification – and its different foci – identifying as a student, employee, working student, or as a student of one’s discipline of study – as potential predictors of important academic (academic self-efficacy, approaches to learning, and academic achievement) and social (status in society) outcomes in three cross-sectional studies. In Study 1, part-time working hours (but not identification processes) were associated with academic self-efficacy. In Study 2, discipline identification and part-time working hours were associated with using deep approaches to learning. In Study 3, student identification was associated with increased status in society. Overall, discipline identification may be solely linked to academic outcomes, yet student identification should be explored further as a potential enhancer of social and graduate outcomes. We discuss additional mechanisms which can help to transform working students’ experiences through their social identities and suggest boundary conditions which can affect the link between these identities and important outcomes.

Economic expedience of waste heat recovery systems (WHRS), especially for low temperature difference applications, is often questionable due to high capital investments and long pay-back periods. By its simple design isobaric expansion (IE) machines could provide a viable pathway to utilize otherwise unprofitable waste heat streams for power generation and particularly for pumping liquids and compression of gases. Different engine configurations are presented and discussed. A new method of modelling and calculation of the IE process and efficiency is used on IE cycles with various pure and mixtures as a working fluid. Some interesting cases are presented. It is shown in this paper, that the simplest non-regenerative IE engines are efficient at low temperature differences between a heat source and heat sink. Efficiency of non-regenerative IE process with pure working fluid can be very high approaching Carnot efficiency at low pressure and heat source/heat sink temperature differences. Regeneration permits to increase efficiency of the IE-cycle to some extent. Application of mixed working fluids in combination with regeneration permits to significantly increase the range of high efficiencies to much larger temperature and pressure differences.

This study seeks to understand, from a gender perspective, the experiences of mining couples in Antofagasta, Chile, especially the negotiation between their intimate lives and the absences of their partners due to the shift work modality. We analyzed testimonies from men and women living in Antofagasta, considered one of the three largest mining regions in the world. Among the main findings, power relations based on the hegemonic gender model supported by the sexual division of labor are identified, which persist in this mining area, despite progress in equity issues in Chile. We propose that, although there are differences between the discourses of men and women and their subjective positioning, both actively collaborate with the reproduction of social gender relations marked by male domination. We observe that this way of living as a couple is associated with the organization of mining work, which is central to the reproduction of the gender order with a hetero-patriarchal tone.

Metal-supported fuel cells (MSCs) offer potential material cost and robustness advantage over anode supported cells (ASCs). Because of the very good thermal shock stability of such MSCs, these can be heated up very quickly. However the challenge co-firing of metal substrate and electrolyte stays still unsolved. The production of the core component, the tape casted metal substrate, with defined shrinkage resulting from modification of metal powders is presented in the paper. This approach leads to an adjustment of the shrinkage mismatch during sintering, between metal and ceramic components, and adjustment of target specifications like porosity, green density and layer thickness.

In this study, we design a new refractive index sensor based on a metal–insulator–metal waveguide coupled with a notched ring and vertical rectangular resonators. We use the finite element method to study the propagation characteristics of the sensor. According to the calculation results, the transmission spectrum exhibits a typical Fano resonance shape. The phenomenon of Fano resonance is caused by the coupling between the wide spectrum and narrow spectrum. In the design, the wide spectrum signal is generated by the vertical rectangular resonator, while the narrow spectrum signal is generated by the notched ring resonator. In addition, we varied the structural parameters of the resonators and filled the structure with media of different refractive indices to study the sensing properties. The maximum achieved sensitivity of the sensor reached 1071.4 nm/RIU. The results reveal potential applications of the coupled system in the field of sensors.

Asthma is a significant public health concern. This study identified the provinces with the highest morbidity and mortality rates due to asthma among the working-age population (15-69 years) in the Republic of Ecuador. The secondary objective was to explain the possible differences attribut-able to occupational exposure. This nationwide ecological and exploratory study was conducted in 24 provinces between 2016 and 2019. Government databases were used as sources of infor-mation. Standardized rates were calculated for codes the J45 and J46. The hospitalization mor-bidity rate for asthma decreased from 6.51 to 5.76 cases per 100,000 working-age population, and the mortality rate has consistently been low and stable from 0.14 to 0.15 deaths per 100,000 working-age population. Geographic differences between the provinces were evident. The risk of hospitalization and death due to asthma was higher in the Pacific coast (five provinces) and the Andean region (two provinces). The high rates observed in provinces with greater agricultural and industrial development could be the main determinants of national heterogeneity and could act as occupational risk factors. The contribution of occupational hazards in each province should be examined in depth through ad hoc studies. These findings provide valuable information for creating public policies aimed at promoting and safeguarding the respiratory health of the popu-lation, particularly that of workers.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

Ion current rectification (ICR) is the ratio of ion current by forward bias to by backward bias and is a critical indicator of diode performance. In previous studies, many attempts have been continued to improve the performance of this ICR, but there is the intrinsic problem for geometric changes that induce ionic rectification due to their fabrication problem. Additionally, the high ICR could be achieved in the narrow salt concentration range only. Here, we propose a multi-layered bipolar ionic diode based on an asymmetric nanochannel network membrane (NCNM), which is realized by soft lithography and self-assembly of homogenous-sized nanoparticles. Owing to the freely changeable geometry based on soft lithography, the ICR performance can be explored according to the variation of microchannel shape. Interestingly, very stable ICR performance can be achieved using the multi-layered 3D configuration for the bipolar diode in a broad range of salt concentrations (0.1mM ~ 100 mM). This demonstrates the promising potential of multi-layered NCNM for applications in highly concentrated electrolytes, such as biosensors, desalination, or energy harvesting.

Nowadays, energy saving is considered a key issue worldwide, as it brings a variety of benefits: reducing greenhouse gas emissions, reducing demand for energy imports, and lowering costs on a household and economy-wide level. Researchers and building designers are looking to optimize building efficiency by means of new energy technologies. Changes in existing buildings can also be made to reduce energy consumption and costs. These may include the usage of new heat transfer fluids based on nanofluids. In this work, an extended experimental campaign (from February 2020 to March 2021) has been carried out on an educational building in the Campus of University of Salento, Lecce – Italy, in order to evaluate the increase in performance of the HVAC system, due to the usage of a nanofluid. The results show that, under optimal operating conditions, plant performance improves more than 10%, with average daily peaks of about 15%.

Working capital management requires a careful attention by the corporate managers because it plays an important role in corporate stability. Social belongingness of managers induced them to learn from their society, colleagues and from overall industrial movement. They also learn from their peers which have more strategical efficiency. In line with these arguments, the objective of current study is to explores the peer influence on corporate working capital management practices. To making analysis, ten-years data (2009-2018) of non-financial publicly listed firms at PSX were collected and the cash conversion cycle (CCC) uses as a proxy variable of working capital management (WCM). To estimate the regression, an econometric technique named the Generalized Method of Moments (GMM) was used. The empirical findings suggest the significant impact of peer WCM on corporate WCM. It also suggests the significant impact of other variables that determine the WCM. This study recommends social learning policy to corporate managers. They can learn from their peers to manage the working capital. Most previous studies discuss the peer influence on investment decisions, corporate cash holding and financing policy, etc., but no study explores such a relationship specifically in the Pakistani non-financial sector data set.