Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

Gaze tracking of high-speed moving targets is a novel application mode for low Earth orbit microsatellites. In this mode, small satellites are equipped with high-resolution narrow-field-of-view video cameras for stable gaze-tracking imaging of high-speed moving targets. This paper proposes a high-precision attitude adaptive integral sliding mode control method with a feedforward compensation disturbance observer to enhance the capability of a microsatellite attitude control system for gaze tracking of high-speed moving targets. Specifically, first, we present the attitude control system model for microsatellites and the calculation method for the desired attitude of target tracking based on image feedback. Then, an adaptive integral sliding mode attitude control algorithm with a feedforward compensation disturbance observer, which meets the requirements of high-precision tracking control, is designed. The developed algorithm utilizes the disturbance observer to observe the friction torque of the flywheel and compensates for it through feedforward control. It also employs the adaptive integral sliding mode control algorithm to reduce the impact of uncertain disturbances, decrease the steady-state error of the system, and enhance the attitude control precision. Simulation experiments demonstrated that the designed disturbance observer can successfully observe the frictional disturbance torque of the flywheel. The attitude Euler angle control precision for high-speed moving target tracking reached 0.009°, and the angular velocity control precision reached 0.005°/s, validating the effectiveness of the proposed approach.

Dynamic optical structural color is always desired in various display applications and usually involves active materials. Full-color generation, especially bi-directional full-color generation in both reflective and transmissive modes, without any active materials included has been rarely investigated. Herein, we demonstrate a scheme of bi-directional full-color generation based on a plasmonic metasurface modulated by rotation of the polarization angle of the incident light without varying the geometry and the optical properties of the materials and the environment where the metasurface resides. The metasurface unit cell consists of plasmonic modules aligning in three directions and is patterned in a square array. The metasurface structural color device generates full colors in both reflection and transmission. Based on the proposed polarization-dependent structural color, information encoding of three multiplexed animal images and quick-responsive (QR) codes is demonstrated to verify the efficient information encoding and decoding of the proposed scheme. The animals can be seen under different polarization incidence and the QR codes can be successfully decoded by the polarization rotation in transmission. The proposed bi-directional full-color generation metasurface has great potential in applications such as kaleidoscope generation, anti-counterfeiting, dynamic color display, and optical information encoding.

For applications in sensing and cavity-based quantum computing and metrology, open-access Fabry-Perot cavities – with an air or vacuum gap between a pair of high reflectance mirrors – offer important advantages compared to other types of microcavities. For example, they are inherently tunable using MEMS-based actuation strategies, and they enable atomic emitters or target analytes to be located at high field regions of the optical mode. Integration of curved-mirror Fabry-Perot cavities on chips containing electronic, optoelectronic, and optomechanical elements is a topic of emerging importance. Micro-fabrication techniques can be used to create mirrors with small radius-of-curvature, which is a prerequisite for cavities to support stable, small-volume modes. We review recent progress towards chip-based implementation of such cavities, and highlight their potential to address applications in sensing and cavity quantum electrodynamics.

In this work modeling and analysis of an integrated opto-fluidic sensor, with a focus on achievement of single mode optical confinement and continuous flow of micro particles in the microfluidic channel for Lab-on-a Chip (LOC) sensing application is presented. This sensor consists of integrated optical waveguides, microfluidic channel among other integrated optical components. A continuous flow of micro particles in a narrow fluidic channel is achieved by maintaining the two sealed chambers at different temperatures and by maintaining a constant pressure of 1Pa at the centroid of narrow fluidic channel geometry. The analysis of silicon on insulator (SOI) integrated optical waveguide at an infrared wavelength of 1550nm for single mode sensing operation is presented. The optical loss is found to be 0.0005719dB/cm with an effective index of 2.2963. The model presented in this work can be effectively used to detect the nature of micro particles and continuous monitoring of pathological parameters for sensing applications.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

In this work, an evanescent Bragg grating sensor inscribed in a few-mode planar polymer waveguide was integrated in microchannel structures and characterized with various chemical applications. The planar waveguide and the microchannels consisted of epoxide-based polymers. The Bragg grating structure was post-processed using point-by-point direct inscription technology. By monitoring the central wavelength shift of the reflected Bragg signal, the sensor showed a temperature sensitivity of -47.75 pm/K. Moreover, the functionality of the evanescent field-based measurements is demonstrated with two application examples: refractive index sensing of different aqueous solutions and gas-phase hydrogen concentration detection. For the latter application, the sensor was additionally coated with a functional layer based on palladium nanoparticles. During the refractive index sensing measurement, the sensor achieved a sensitivity of 6.5 nm/RIU from air to 99.9% pure isopropyl alcohol. For the gas-phase hydrogen detection, the coated sensor achieved a reproducible concentration detection up to 4 vol% hydrogen. According to the reported experimental results, the integrated Bragg grating-based waveguide sensor demonstrates high potential for applications based on lab-on-a-chip concept.

The aim of this research work is to get a method for Galfenol electrodeposition thought which we can control the desired percentage of Ga versus Fe that has the maximum magnetostriction constant. Galfenol is electrodeposited on an optical fiber with an imbedded Fiber Bragg Grating (FBG) in its core. The final objective, that goes further of the scope of this research, is to get an optical magnetostrictive sensor. The device will sense magnetic field or current based on the combination of this magnetostrictive Galfenol, that will stress the optical fiber with the application of magnetic field or current and will change the reflected wavelength of the FBG as a consequence of the variation of the Bragg wavelength. We have developed a method of electrodeposition that allows controlling the density of current in the electrodeposition process in order to get the desired percentage of Ga and Fe in the alloy Ga X Fe 1-x. We have manufactured a set of samples with different parameters (as density of current and pH) and we have characterized these samples morphological, structural and magnetically. With this research we want to give to the scientific community the groundwork to design magnetostrictive optical sensors based on and FBG coated by giant magnetostrictive material. In this paper we have developed a method of covering the optical fiber controlling the composition of (Ga X Fe 1-X) in order to be able to get the maximum magnetostriction constant.

This study addresses the implementation of the International Financial Reporting Standard 9 (IFRS 9) in the European Union as of January 1, 2018, replacing the International Accounting Standard 39 (IAS 39) to introduce a new model for recognizing Loan Loss Provisions (LLP) based on Expected Credit Loss (ECL). This model responds to criticisms of the former Incurred Credit Loss (ICL) system for its inability to reflect credit losses in a timely manner, potentially exacerbating the effects of financial crises (Bushman & Williams, 2015; Gebhardt & Novotny-Farkas, 2011). The study focuses on the effects of adopting the ECL model on the level of Loan Loss Allowances (LLA) in loans, own equity, and the Common Equity Tier 1 (CET1) ratio across 13 Portuguese commercial banks. A mean comparison test is used to evaluate scenarios before and after the application of the ECL model, highlighting the importance of regulator actions and the adequacy of loss recognition policies, including the effects of Regulation (EU) 2017/2395 of December 12. The results obtained demonstrate significant negative impacts on the net values of loans, own equity, and the CET1 ratio upon adopting the IFRS 9 ECL model, due to the widespread increase in LLAs.

Understanding the dynamics of Organic Carbon mineralization is fundamental in forecasting biosphere to atmosphere Net Carbon Ecosystem Exchange (NEE). With this perspective, we developed 3D-CMCC-PSM, a new version of the hybrid Process Based Model 3D‐CMCC FEM where also heterotrophic respiration (R_h) is explicitly simulated. The aim was to quantify NEE as a forward problem, by subtracting Ecosystem Respiration (R_eco) to Gross Primary Productivity (GPP). To do so, we developed a simplification of the Soil Carbon dynamics routine proposed in DNDC [1]. The method calculates decomposition as a function of soil moisture, temperature, state of the organic compartments, and relative abundance of microbial pools. Given the pulse dynamics of soil respiration, we introduced modifications in some of the principal constitutive relations involved in phenology and littering sub-routines. We quantified the model structure related uncertainty in NEE, by running our training simulations over 1000 random parameter-sets extracted from parameters distributions expected from literature. 3D-CMCC-PSM predictability was tested on independent time series for 6 Fluxnet sites. The model resulted in daily and monthly estimations highly consistent with the observed time series. It showed lower predictability in Mediterranean ecosystems, suggesting that it may need further improvements in addressing evapotranspiration and water dynamics.

Droplet-based microfluidics has revolutionized numerous fields such as biomedical research, pharmaceuticals, drug discovery, food engineering, flow chemistry, and cosmetics. This paper presents a comprehensive study focusing on the detection and characterization of droplets with volumes in the nanoliter range. Leveraging the precise control of minute liquid volumes, we introduced a novel spectroscopic On-Chip microsensor equipped with integrated microfluidic channels for droplet generation, characterization, and sensing, simultaneously. The microsensor, designed with Interdigitated-Ring-Shaped Electrodes (IRSE) and seamlessly integrated with microfluidic channels, offers enhanced capacitance and impedance signal amplitudes, reproducibility, and reliability in droplet analysis. We were able to make analyses of droplets length in the range 1.0-6.0 mm, velocity 0.66-2.51 mm/s, droplet volume 1.07nL-113.46nL. Experimental results demonstrated that the microsensor's has a great performance in terms of droplet size, velocity, and length, with a significant signal amplitude of capacitance and impedance, and real-time detection capabilities, thereby highlighting its potential for facilitating microcapsule reactions and enabling on-site real-time detection for chemical and biosensor analyses on-chip.

Often, engineers with machining experience often judge machining state and tool life according to chips’ features. Engineers' experience is digitized in this study. During the cutting process, the cutting tool coming in contact with the workpiece produces a shear zone, which causes plastic deformation and shear slip. The chips closest to the shear zone can directly show the state of the tool and workpiece when the material is SKD61. This study used chip color, vibration, and current signal integration for prediction of machining state and cutting tool life. When the cutting tool wears increased, the chip surface color changed in the following way: purpleè purple blueè blue ècyan, or even green and yellow. When the cutting tool was in the accelerating wear phase, the color change was particularly obvious. The Back-Propagation Levenberg–Marquardt (BP-LM) predictive methodology was used to compare the predictive ability of voltage, vibration signal, and chip color. The Mean Absolute Percentage Error (MAPE) for the voltage signal was 12.28%, for the vibration signal it was 11.38%, and for the chip color combined with multi-sensor characteristics it was 7.85%. The MAPE of the chip color was the smallest. Using the General Regression Neural Network (GRNN) methodology, the MAPE for the voltage signal was 10.74%, for the vibration signal 7.96%, and for the chip color combined with multi-sensor characteristics was 6.59%. The MAPE of the chip color was the smallest. Obviously, the chip color combined with multi-sensor signals provided better predictive results than the vibration signal or voltage signal alone. There is currently no research on the usefulness of monitoring chip color for tool life prediction.

Cancer treatment is a significant focus in medicine owing to the increasing global incidence. Patients with advanced cancers that do not respond to conventional therapies have limited options and an unfavorable prognosis. Consequently, researchers are investigating complementary approaches to conventional treatments. One such approach is alkalization therapy, which aims to neutralize the acidic tumor microenvironment (TME) by increasing its pH level. The acidic TME promotes inflammation, tumor progression, and drug resistance. Alkalization therapy has been demonstrated to be effective for various cancers. In addition, natural products, such as triterpenoids, parthenolides, fulvic acid, Taxus yunnanensis, and apple pectin have the potential to alleviate symptoms, maintain physical fitness, and improve treatment outcomes of cancer patients through their anti-inflammatory, antioxidant, and anticancer properties. In this review, we focus on the effects of alkalization therapy and natural products on cancer. Furthermore, we present a case series of advanced cancer patients who received alkalization therapy and natural products alongside standard treatments, resulting in long-term survival. We posit that alkalization therapy together with the supplementation of natural products may confer benefits to cancer patients by mitigating the side effects of chemotherapy and complementing standard treatments. However, further research is warranted to validate these clinical findings.

System-of-systems (SoS) evolution is a complex and unpredictable process. Although various principles to facilitate collaborative SoS evolution have been proposed, there is a lack of experimental data validating their effectiveness. To address these issues, we present an Agent-Based Model (ABM) for SoS evolution in the Internet of Vehicles (IoV) , serving as a quantitative analysis tool for SoS research. By integrating multiple complex and rational behaviors of individuals, we aim to simulate real-world scenarios as accurately as possible. To simulate the SoS evolution process, our model employs multiple agents with autonomous interactions and incorporates external environmental variables. Furthermore, we propose three evaluation metrics: evolutionary time, degree of variation, and evolutionary cost, to assess the performance of SoS evolution. Our study demonstrates that enhanced information transparency significantly improves the evolutionary performance of distributed SoS. Conversely, the adoption of uniform standards only brings limited performance enhancement to distributed SoSs. Although our proposed model has limitations, it stands out from other approaches that utilize Agent-Based Modeling to analyze SoS theories. Our model focuses on realistic problem contexts and simulates realistic interaction behaviors. This study enhances the comprehension of SoS evolution processes and provides valuable insights for the formulation of effective evolutionary strategies.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

Organ-on-Chip is a game-changing technology born from the convergence of tissue engineering and microfluidic technology. Organ-on-Chip devices (OoCs) are expected to offer effective solutions to persisting problems in drug development and personalized disease treatments. This opinion paper surveys the current landscape in research, development, application and market opportunities for OoCs to help establishing a global and multi-stakeholder OoC ecosystem. Based on a bibliometric study, a market analysis, expert interviews, and panel discussions held at the ORCHID Vision Workshop (Stuttgart, 23 May 2018), we outline presently unmet needs, key challenges, barriers and perspectives of the field, and finally propose recommendations towards the definition of a comprehensive roadmap that could render OoCs realistic models of human (patho)physiology in the near future.

Railway has been used as one of the most crucial means of transportation in public mobility and economic development. For efficiently operating railways, the electrification system in railway infrastructure, which supplies electric power to trains, is essential facilities for stable train operation. Due to its important role, the electrification system needs to be rigorously and regularly inspected and managed. This paper presents a supervised learning method to classify Mobile Laser Scanning (MLS) data into ten target classes representing overhead wires, movable brackets and poles, which are recognized key objects in the electrification system. In general, the layout of railway electrification system shows a strong regularity of spatial relations among object classes. The proposed classifier is developed based on Conditional Random Field (CRF), which characterizes not only labeling homogeneity at short range, but also the layout compatibility between different object classes at long range in the probabilistic graphical model. This multi-range CRF model consists of a unary term and three pairwise contextual terms. In order to gain computational efficiency, MLS point clouds is converted into a set of line segments where the labeling process is applied. Support Vector Machine (SVM) is used as a local classifier considering only node features for producing the unary potentials of CRF model. As the short-range pairwise contextual term, Potts model is applied to enforce a local smoothness in short-range graph. While, long-range pairwise potentials are designed to enhance spatial regularities of both horizontal and vertical layouts among railway objects. We formulate two long-range pairwise potentials as the log posterior probability obtained by Naïve Bayes classifier. The directional layout compatibilities are characterized in probability look-up tables which represent co-occurrence rate of spatial relations in horizontal and vertical directions. The likelihood function is formulated by multivariate Gaussian distributions. In the proposed multi-range CRF model, the weight parameters to balance four sub-terms are estimated by applying the Stochastic Gradient Descent (SGD). The results show that the proposed multi-range CRF can effectively classify detailed railway elements, representing the average recall of 97.66% and the average precision of 97.07% for all classes.

The pharmacological effects of the fruiting body of Ophiocordyceps sinensis (Os) exerted antioxidant, anti-virus, and immunomodulatory, whereas the anti-inflammatory effects and active components of Os mycelial submerged culture (OMSC) are not known. This study aimed to investigate the active compounds in the fermented liquid (FLOS), hot water (WEOS), and 50-95% (EEOS-50, EEOS-95) ethanol extracts of OMSC and their anti-inflammatory effects and potential mechanisms in LPS-stimulated microglial BV2 cells. The results demonstrated that all of the OMSC extracts could inhibit NO production in BV2 cells. EEOS-95 exhibited the strongest inhibitory effects (41 % inhibitory ability at 500 µg/mL), and its ergosterol, GABA, total phenolic, and total flavonoid contents were significantly higher than those of the other extracts (18.60, 18.60, 2.28, and 2.14 mg/g, p < 0.05, respectively). EEOS-95 also has a strong inhibitory ability against IL-6, IL-1β and TNF-α with IC50 of 617, 277 and 507 µg/mL, respectively, which is higher than that of 1 mM melatonin. The anti-inflammatory mechanism of EEOS-95 seems to be associated with up-regulation of PPAR-γ/Nrf-2/HO-1 antioxidant-related expression and down-regulation of NF-κB/COX-2/iNOS pro-inflammatory expression signaling. Therefore, we hypothesized that EEOS-95 can prevent neurodegenerative diseases, but the effect on the application in vivo should be further investigated.

Gene regulation is vital for cellular function and homeostasis, involving diverse mechanisms controlling specific gene products and contributing to tissue-specific gene expression. Dysregulation leads to diseases, emphasizing the need for understanding these mechanisms. Non-coding regions, notably enhancers and super-enhancers (SEs), act as crucial gene regulators, orchestrating transcriptional activity via transcription factors (TFs). SEs, with high activity, are pivotal in cell identity and disease progression. Current computational approaches focus on individual regulators like TFs and miRNAs, neglecting SE interactions. We emphasize incorporating SEs into models to enhance understanding. Experimental studies have recently linked miRNAs and TFs to SEs. Chromatin immunoprecipitation followed by sequencing (ChIP-Seq) provides valuable SE information. In this review, we categorize computational methods leveraging TF and miRNA data into three areas and explore challenges integrating enhancers/SEs. These include unraveling indirect regulatory networks, identifying network motifs, and enriching pathway identification by dissecting gene regulators, including SEs. We hypothesize that addressing these challenges will enhance our understanding of gene regulation, aiding in identifying therapeutic targets and disease biomarkers. We believe that understanding the role of ChIP-Seq data in predicting the effect of miRNA on gene regulation is crucial to construct statistical/computational model that would tackle these challenges.

The wealth of data obtained during the past 20 years using Laser-Induced Breakdown Spectroscopy (LIBS) indicates that the technique is very promising to detect small chemical contents of alloying elements. The potential of LIBS was looked more seriously during the past two decades or so as more data were obtained on Aluminum and steel to study the phenomena in the condition of local thermodynamic equilibrium and time-delay between a Q-switch laser and an intensified CCD camera. Since the past decade, some data on compounds were also shown to be useful in determining small concentrations of harmful elements. This manuscript is intended to show that the technique of LIBS performance is very promising in fields such as micro-machining, in alloying element analysis, surface cleaning and environmental applications even with lightweight spectrometers having a relatively low resolution, which can potentially be air-borne.

In this paper we report a new development on the numerical model for aluminum-steam combustion. This model is based on diffusion flame of continuum regime and the thermal equilibrium between the particle and the flow field, which can be used to calculate the aluminum particle combustion model for two phase calculation conditions. The model prediction is in good agreement with the experimental data. A new type of vortex combustor was proposed for the combustion of aluminum and steam, and the mathematical model of the two phase reacting flow with in this combustor was established. The turbulence effects are modeled using the Reynolds Stress Model (RSM) with Linear Pressure-Strain approach, and the Eddy-Dissipation model is used to simulate the gas phase combustion. Aluminum particles are injected into the vortex combustor and form a swirling flow around the chamber and their trajectories are traced using the Discrete Phase Model (DPM). The simulation results show that the vortex combustor can achieve high efficient combustion of aluminum and steam. The influencing factors, such as the eccentric distance of the inlet of aluminum particles, particle size and steam inlet diameter, etc., are studied. The work described in this paper represents an attempt to the design of a vortex combustor in order to increase aluminum combustion efficiency.

We report world record high data transmission over standard optical fiber from a single optical source. We achieve a line rate of 44.2 Terabits per second (Tb/s) employing only the C-band at 1550nm, resulting in a spectral efficiency of 10.4 bits/s/Hz. We use a new and powerful class of micro-comb called soliton crystals that exhibit robust operation and stable generation as well as a high intrinsic efficiency that, together with an extremely low spacing of 48.9 GHz enables a very high coherent data modulation format of 64 QAM. We achieve error free transmission across 75 km of standard optical fiber in the lab and over a field trial with a metropolitan optical fiber network. This work demonstrates the ability of optical micro-combs to exceed other approaches in performance for the most demanding practical optical communications applications.

The refractive index of seawater is one of the essential parameters in ocean observation, so it is necessary to achieve high precision seawater refractive index measurement. In this paper, we propose a method for measuring the refractive index of seawater based on a Position Sensitive Detector (PSD). Theoretical model is established to depict the correlation between laser spot displacement and refractive index change, utilizing a combination of position sensitive detector and laser beam deflection principle. Based on this optical measurement method, a seawater refractive index measurement system was established. To effectively enhance the sensitivity of refractive index detection, a focusing lens was incorporated into the optical path of the measuring system, and simulations were conducted to investigate the impact of focal length on refractive index sensitivity. The calibration experiment of the measuring system was performed based on the relationship between refractive index of seawater and underwater pressure (depth). By measuring laser spot displacement at different depths, changes in displacement with respect to both refractive index and depth were determined. Experimental results demonstrate that the system exhibits a sensitivity of 9.9277×10−9RIU (refractive index unit), the refractive index deviation due to stability is calculated as ±7.545×10−9RIU. Thereby the feasibility of highly sensitive measurement of seawater refractive index is verified.

Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

In this paper, an ultracompact combined sensor for displacement and angle synchronous measurement is proposed based on self-imaging effect of optical microgratings. Using a two-grating structure, linear and angular displacement can be measured by detecting the change of phase and amplitude of the optical transmission respectively within one single structure in meantime. The optical transmitted properties of the two-grating structure are investigated in both theory and simulation. Simulated results indicate that, the optical transmission changes in a sinusoidal relationship to the input linear displacement. Meanwhile, the amplitude of the curve decreases with an input pitch angle, indicating the ability for synchronous measurement within one single compact structure. The synchronous measurement of the linear displacement and the angle is also demonstrated experimentally. The results show a resolution down to 4nm for linear displacement measurement, and a sensitivity of 0.26mV/arcsec within a range of ±1° for angle measurement. Benefitting from a simple common-path structure without using optical components including reflectors and polarizers, the sensor shows an ultrahigh compactness for multiple-degrees-of-freedom measuring, indicating the great potential for this sensor in the fields such as integrated mechanical positioning and semiconductor fabrication.

Over the past decade, Deep Learning (DL) had been applied in a large number of optical sensors’ applications. DL algorithms can improve the accuracy and reduce the noise level in optical sensors. Optical sensors are considered as promise technology for the modern intelligent sensing platforms. These sensors are widely used to process monitoring, quality prediction, pollution, defense, security and many other applications. However, they suffer major challenges such as the large generated data and low processing speed for that data and moreover the much cost of these sensor. These challenges can be mitigated by integrating deep learning system with the optical sensor technologies. This paper presents recent studies that integrate DL algorithms with optical sensors applications. This paper also highlights several of DL algorithms directions that promise a considerable impact on use for optical sensor applications. Moreover, this study provides new directions for the future related research development.

This paper presents a new optical, multi-functional, high-resolution 3-axis sensor which serves to navigate and can, for example, replace standard joysticks in medical devices such as electric wheelchairs, surgical robots or medical diagnosis devices. A light source, e.g. a laser diode is affixed to a movable axis and projects a random geometric shape on an image sensor (CMOS or CCD). The software in the downstream microcontroller identifies the geometric shape’s center, distortion and size, then calculates X, Y, and Z coordinates. These coordinates can then be processed in attached devices. The 3-axis sensor is characterized by its very high resolution, precise reproducibility and plausibility of the coordinates produced. In addition, optical processing of the signal provides a high level of safety against electromagnetic and radio frequency interference. The sensor presented here is adaptive and can be adjusted to fit a user’s range of motion (stroke and force). This recommendation aims to optimize sensor systems such as joysticks in medical devices in terms of safety, ease of use, and adaptability.

National heatwave plans are aimed at reducing the avoidable human health consequences due to heatwaves, by providing warnings to and improving communication between relevant stakeholders. The aim of this study was to assess the perceptions of key stakeholders within plans in Belgium and the Netherlands on their responsibilities, the partnerships, and the effectiveness of the local implementation in Brussels and Amsterdam. Key informant interviews were held with stakeholders that had an important role in development of the heatwave plan in these countries, or its implementation in Brussels or Amsterdam. Care organisations, including hospitals and elderly care organisations, had a lack of familiarity with the national heatwave plan in both cities, and prioritised heat the lowest. Some groups of individuals, specifically socially isolated individuals, are not sufficiently addressed by the current national heatwave plans and most local plans. Stakeholders reported that responsibilities were not clearly described and that the national plan does not describe tasks on a local level. We recommend to urgently increase awareness on the impact of heat on health among care organisations. More emphasis needs to be given to the variety of heat risk groups. Stakeholders should be involved in the development of updates of the plans.

Statistical denoising techniques have been well studied, however many challenges still remain. This 9 article focuses on determining the least necessary number of significant samples in a statistical pop-10 ulation sampling, while minimizing the impact on the statistical detection of the fiber Bragg grating 11 (FBG) power spectra. This is achieved by using Bayesian decision making, small population statis-12 tics while excluding false detection. First, we investigate the impact of two-sided sliding window 13 technique applied near the cell under the test. The window size varies from 8 to 60 samples. The 14 considered maximum size of population sampling is connected with the number of wavelength 15 samples within the bandwidth of the symmetrical FBG power spectra peaks. Regarding the sym-16 metry of FBG power spectra peaks and the possible reduction of computational demands, we inves-17 tigate the impact of a one-sided sliding window. This enables to achieve less processing latency for 18 real time applications thus brings benefits to FBG-based fiber optical sensing. Both, two- and one-19 sided small population sampling techniques are then experimentally verified. Detection results are 20 analyzed in depth via calculating detection thresholds by using the small size window sliding along-21 side the waveband. From results achieved, it was found that the normality three-sigma rule does 22 not need to be followed while using the small population sampling. Experimental demonstrations 23 and analyses showed that the proposed concept of denoising and statistical threshold detection 24 based on the sliding window does not depend on the prior knowledge of probability distribution 25 functions of the FBG power spectra peaks level and background noise. We have also found that the 26 thresholds’ adaptability mainly depends on the statistical numerical characteristics of the above ad-27 ditive mixture of the FBG power spectra peaks signals and background noise.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of >1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

In the mold machining process, the cutting tool is worn with machining time, thereby affecting the surface accuracy, leading to poor workpiece dimensions, even fracture. At present, many studies have used multiple sensors to detect the machining conditions of cutting tool and workpiece, including indirect measurement method and direct measurement method. The indirect measurement method, which has been studied widely, mainly uses sensors to capture signals for subsequent data analysis; the direct measurement method mainly analyzes the state of cutting shear zone. Due to the cut-in of cutting tool in the machining process, the workpiece is dislocated rapidly, generating considerable amount of heat, which is transferred to the chips, inducing color change on the surface of chips. Many engineers with machining experience often judge the machining state and tool life according to the chips. The engineers' experience is digitized in this study, and indirect measuring sensors are used to predict the tool life, so as to attain the objective for smart manufacturing, the average percentage error of MAPE using single vibration and voltage eigenvalues as input features is 10%, the voltage signal characteristic values and vibration signal characteristic values are combined. Finally, the chip surface chromaticity eigenvalue is combined with signal characteristic value. The average prediction error of BP-LM method is 7.85%, the average prediction error of GRNN method is 6.59%. Therefore, when the eigenvalue of chip surface chromaticity is added to the prediction result, it can enhance the accuracy of cutting tool wear value prediction more effectively than single sensor signal characteristic value.

Lactoperoxidase (LP), which is a high-value minor whey protein, has recently drawn extensive attention from research scientists and industry due to its multi-function and potential therapeutic applications. In this study, the separation and optimization of two similar-sized proteins, LP and lactoferrin (LF) were investigated using strong cation exchange column chromatography. Optimization was started with central composite design based experiments to characterize the importance of different decision variables. The three variables used in the optimization were flow rate, length of gradient and final salt concentration in the linear elution gradient step. The obtained empiric functional model represented the effect of the significant factors on the yield as the objective function. Afterwards, the calibrated mechanistic model was employed to predict accurate optimal set of variables. The optimal operating points were found and the results were compared with validation experiments. Predictions respecting yield confirmed a very good agreement with experimental results while keeping purity, a product quality characteristic, equal or above to a predefined value.

This article argues that philosophy and its influential narrative should take and think "food" - the gastro-world - in order to radically renew itself and develop a gastrocentric view of the world and the future of humanity. It discusses first some of the basic ideas of a gastrocentric understanding of the world, second the adventure of becoming a Terran, and third the daily practice of what I will call "terra madre forming". It tells us this: If there is to be a future of human survival and well-being on Earth, if we are to achieve the goals of sustainable development, then we have a clear agenda for tomorrow with the re-humidification of the soil - madre terra - that nourishes us. What needs to be done is quite simple and down-to-earth: We, each of us, if possible, must participate in the regeneration of the earth. In conclusion, it is time for the Slow Food movement to blossom into a geo-gastro-activism. The future task of this organization is to make itself electable as a political party to support the much-needed transformation of humans into Terrans.

Considering characteristics of high river density, special underlying surface in plain river network region, and municipal drainage system function, river network drainage unit model is proposed, which is defined as a region surrounded by main river or embankment. Flood storage variety and control projects regulation of small rivers in each unit is simulated. With drainage catchment as an object, according to its drainage capacity, simplified municipal drainage model was developed. Coupling river network drainage unit model, simplified municipal drainage model and 2D flood routing model, urban flood analysis model for plain tidal river network region was developed, which could be applied to analyzing flood from upstream river, storm surge and local rainfall. Demonstration research was carried out in Puxi flood protected area in Shanghai.

Optical fiber sensors based on tapered optical fiber (TOF) structure have attracted a considerable amount of attention from researchers due to the advantages of simple fabrication, high stability, diverse structures, and have great potential for applications in many fields such as physics, chemistry and biology. Compared with ordinary optical fibers, TOF with their unique structural characteristics significantly improve the sensitivity and response speed of fiber-optic sensors and broaden the application range. This review presents an overview of the latest research status and characteristics of fiber-optic sensors and TOF sensors. Then the working principle of TOF sensors, fabrication schemes of TOF structures, novel TOF structures in recent years, and the growing emerging application areas are described. Finally, the development trends and challenges of TOF sensors are prospected. The objective of this review is to convey novel perspectives and strategies for the performance optimization and design of TOF sensors based on fiber-optic sensing technologies.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

Using coherent optical detection and digital signal processing, laser phase noise and equalization enhanced phase noise can be effectively mitigated using the feed-forward and feed-back carrier phase recovery approaches. In this paper, theoretical analyses of feed-back and feed-forward carrier phase recovery methods have been carried out in the long-haul high-speed n-level phase shift keying (n-PSK) optical fiber communication systems, involving a one-tap normalized least-mean-square (LMS) algorithm, a block-wise average algorithm, and a Viterbi-Viterbi algorithm. The analytical expressions for evaluating the estimated carrier phase and for predicting the bit-error-rate (BER) performance (such as the BER floors) have been presented and discussed in the n-PSK coherent optical transmission systems by considering both the laser phase noise and the equalization enhanced phase noise. The results indicate that the Viterbi-Viterbi carrier phase recovery algorithm outperforms the one-tap normalized LMS and the block-wise average algorithms for small phase noise variance (or effective phase noise variance), while the one-tap normalized LMS algorithm shows a better performance than the other two algorithms for large phase noise variance (or effective phase noise variance). In addition, the one-tap normalized LMS algorithm is more sensitive to the level of modulation formats.

Organ-on-a-Chip (OoC) systems bring together cell biology, engineering, and material science for creating systems that recapitulate the in vivo microenvironment of tissues and organs. The versatility of OoC systems enables in vitro models for studying physiological processes, drug development, and testing in both academia and industry. This paper evaluates current platforms from the end-user perspective, elaborating on usability, complexity, and robustness. We surveyed 165 peers in over 30 countries and grouped the responses according to preliminary knowledge and the source of the OoC systems that are used. The survey clearly shows that current commercial OoC platforms provide a substantial level of robustness and usability - which is also indicated by an increasing adaptation of the pharmaceutical industry but a lack of complexity can challenge their use as a predictive platform. Self-made systems on the other hand are less robust and standardized but provide the opportunity to develop customized and more complex models which are often needed for human disease modeling. This review serves as a guide for researchers in the OoC field and encourages the development of next-generation OoCs.

In order to investigate the size distributions and seasonal variations of carbonaceous aerosols (OC and EC), the carbonaceous species were collected and then analyzed by using a 9-stage Anderson-type aerosol sampler and DRI Model 2001A Thermal/Optical Carbon Analyzer on the typical industrial city Nanjing in Yangtze River Delta, China in the summer, autumn and winter of 2013 and spring of 2014. OC, EC, SOC and POC exhibited obvious seasonal variations, with the highest level in winter (39.1±14.0, 5.7±2.1, 23.6±11.7 and 14.1±5.7 μg•m^-3) and the lowest level in summer (20.6±6.7, 3.3±2.0, 12.2±3.8 and 8.4±4.1 μg•m^-3), and were mainly centralized in PM_1.1 in four seasons. The concentrations of OC in PM_1.1 varied in the order of winter > autumn > spring > summer, while EC ranked in the order of autumn > winter > summer > spring. In the PM_1.1-2.1 and PM_2.1-10, the concentrations of OC and EC decreased in the sequence of winter > spring > autumn > summer. The size spectra of OC, EC and SOC had bimodal distributions in four seasons, except for EC with four peaks in summer. The size spectra of POC varied greatly with seasons, exhibiting bimodal distribution in winter, trimodal distribution in spring and summer, and four peaks in autumn. The OC/EC ratios were 7.0, 6.3, 7.6 and 6.9 in spring, summer, autumn and winter, respectively, which demonstrated the abundance of secondary organic aerosols in Nanjing. The sources of carbonaceous aerosol varied significantly with seasons, and were dominated by vehicle exhaust, coal and biomass burning in PM_2.1, and dominant by dust, coal and biomass burning in PM_2.1-10.

In the field of clinical medicine, the real-time monitoring of carbon dioxide gas exhaled by the human body is of great significance. At present, the detection devices in the market are mainly detected by sucking a small amount of gas in the nasal cavity to the detection device, and there are some problems such as too long sampling tubes, easy blockage or distortion, and abnormal gas dispersion. In this paper, a micro-nano optical fiber sensor that can directly detect the concentration of end-tidal carbon dioxide is proposed. The measurement is achieved by using the principle of high evanescent field absorption, and the operating band is 2.004 μm. The sensor uses micro-nano optical fiber as the sensing area, and then detects the presence of carbon dioxide gas exhaled by human body through optical power attenuation. The function of micro-nano fiber is to realize the transmission of signal light and also serve as the absorption medium of the gas to be measured. In addition, the variation of light power also reflects the respiratory cycle of the human body. The sensor can realize rapid real-time response to carbon dioxide gas detection, with small size, low cost, and easy to replace. It has great application potential in clinical scenarios such as Gastrointestinal Endoscopes that require real-time monitoring of human respiration.

Bartonella species, intracellular parasitic zoonotic pathogens, has drawn increasing attention for their diverse host range and associated human diseases. This study investigates Bartonella infection in small mammals in Yunnan Province, China, focusing on tissue tropism. 333 small mammals were sampled from 13 species, 3 orders, 4 families, and 4 genera in Heqing and Gongshan Counties. Conventional PCR and real-time quantitative PCR (qPCR) were utilized for detection and quantification, followed by bioinformatic analysis of obtained DNA sequences. Results show a 31.5% detection rate, varying across species. Notably, Apodemus chevrieri, Eothenomys eleusis, Niviventer fulvescens, Rattus tanezumi, Episoriculus leucops, Anourosorex squamipes, and Ochotona Thibetana exhibited infection rates of 44.4%, 27.7%, 100.0%, 6.3%, 60.0%, 23.5%, and 22.2%, respectively. Genetic analysis identified 30, 10, and 5 strains based on ssrA, rpoB, and gltA genes, with nucleotide identities ranging from 92.1% to 100.0%. Bartonella strains were assigned to B. grahamii, B. rochalimae, B. sendai, B. koshimizu, B. phoceensis, B. taylorii, and a new species identified in the Episoriculus leucops (GS136). Tissue distribution analysis revealed varied copy numbers across different tissues, with the highest load in spleen. These findings underscore Bartonella's diverse species and host range in Yunnan Province, highlighting its broad tissue tropism in small mammals.

Due to the renewed variation in government and political systems inside and outside countries, and with the high tariffs at borders, the latter have become an outlet for terrorism and smugglers. Therefore, each country seeks to develop its own protection system, and the technologies used in these systems vary according to the severity and the importance of the installations to be protected, it is found that some of them are expensive and unnecessary, but other have good and variable levels of efficiency. Consequently, the idea of designing a surveillance system that can monitor and control access becomes indispensable. In the same context, this work is of crucial strategic and geopolitical importance. It combines pre-existing alarm and monitoring methods and revolutionary Internet of Things (IoT) application products, of which Wireless Sensor Networks (WSN) and Optical Fiber Sensors (OFS) are part of this application. This article presents the distribution of wireless radar nodes accompanying with a Bragg fiber sensor to identify each rolling intruder incoming the zone to be monitored, from the determination of its speed, weight and wheelbase distance.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

In this work, two plasmonic structures with two different periodic nanostructures (nanodisk and nanostrip arrays) separated from the gold layer by an ultrathin dielectric Al2O3 layer are proposed, and their optical properties are simulated as 3-dimensional models using COMSOL Multiphysics software tool. The optical responses, such as the amplification of the electric field and the scattering, absorption and extinction cross sections of the two structures, are investigated and compared. The results show that both structures show strong field enhancement in their gap layer, and the structure with the periodic array of metal nanodisks shows stronger field enhancement and larger absorption, extinction, and scattering cross sections in its dipole resonance wavelength, which is defined as a bright plasmonic mode. In addition, some weaker resonant modes are observed for both structures and the reason for their generation is dis-cussed. The analysis of different possible modes in such structures is crucial for their application in various fields.

Optical backbone networks constitute the fundamental infrastructure employed today by network operators to deliver services to users. As network capacity is a key factor influencing optical network performance, it is important to understand how topological and physical properties impact its behavior and to have the capability to estimate its value. In this context, we propose here a method to evaluate the network capacity that relies on the optical reach to account for physical layer aspects, in conjunction with constrained routing techniques for traffic routing. As this type of routing can lead to traffic blocking, particularly due to the limitation on the number of wavelengths per fiber, we also propose a fiber assignment algorithm designed to deal with this problem. We apply this method to a set of randomly generated networks using a modified Waxman model, and for a network with 60 nodes, in a scenario without blocking, we obtain capacities of about 2.5 Pbit/s for a symbol rate of 64 Gbaud and about 5 Pbit/s for a symbol rate of 128 Gbaud. Remarkably, this duplication in the total network capacity is achieved by an increase in the total fiber length of only about 51%.

Quantum correlations, especially time correlations, are crucial in ghost imaging in order to significantly reduce the background noise on the one hand while increasing the imaging resolution. Moreover, the time correlations serve as a critical reference, distinguishing between signal and noise, which in turn enable clear visualization of biological samples. Quantum imaging also addresses the challenge involved in imaging delicate biological structures with minimal photon exposure and sample damage. Here we explore the recent progress in quantum correlation-based imaging, notably its impact on secure imaging and remote sensing protocols as well as on biological imaging. We also exploit the quantum characteristics of heralded single-photon sources (HSPS) combined with decoy-state methods for secure imaging. This method uses Quantum Key Distribution (QKD) principles to reduce measurement uncertainties and protect data integrity. It is highly effective in low-photon-number regimes for producing high-quality, noise-reduced images. The versatility of decoy-state methods with WCSs (WCS) is also discussed, highlighting their suitability for scenarios requiring higher photon numbers. We emphasize the dual advantages of these techniques: improving image quality through noise reduction and enhancing data security with quantum encryption, suggesting significant potential for quantum imaging in various applications, from delicate biological imaging to secure quantum communication.

Conventional methods for pathogen detection in water rely on time-consuming enrichment steps followed by biochemical identification strategies, which require assay times ranging from 24 hours to up to a week. However, in recent years, significant efforts have been made towards the development of biosensing technologies enabling rapid and close-to-real-time detection of waterborne pathogens. In previous studies, we developed a plastic optical fiber (POF) immunosensor using an optoelectronic configuration consisting of a U-Shape probe connected to an LED and a photodetector. Bacterial detection was evaluated with the immunosensor immersed in a bacterial suspension in water with a known concentration. Here, we report on the sensitivity of a new optoelectronic configuration consisting of two POF U-Shape probes, one as the reference and the other as the immunosensor, for the detection of Escherichia coli. In addition, another way of detection was tested where the sensors were calibrated in the air, before immersed in bacterial suspension and then read in the air, making the immunosensor more sensitive and with a faster detection time. This new sensor detected the presence of E. coli at 104 CFU/mL in less than 10 minutes. Currently sub 10 minutes is faster than previous studies using fiber-optic based biosensors. It is also a much simpler and quicker methodology when compared with conventional laboratory technology.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

In this paper, a continuous power management for a decentralized DC microgrid (DCMG) is proposed to achieve voltage regulation and power balance even under system uncertainty and voltage sensor failure. The DCMG system achieves a continuous power management through only the primary controller to reduce the computational burden of each power agent. To enhance the reliability and resilience of the DCMG system under voltage sensor failure, a DC bus voltage (DCV) sensor fault detection algorithm is proposed. In this algorithm, the DCV sensor failure is detected by comparing the measured DCV with the estimated DCV. When the power agent identifies the DCV sensor failure, it changes the operation properly according to the proposed control mode decision algorithm to maintain the stability of the DCMG system. When uncertain conditions such as the power variation of the distributed generations, sudden grid disconnection, DCV sensor failure, electricity price change, and critical battery status occur, the DCMG system is changed to transitional operation modes. These transitional operation modes are employed to transmit the power agent information to other agents without digital communication links (DCLs) and to accomplish power sharing even under such uncertain conditions. In the transitional operation modes of the DCMG system, the DCV levels are temporarily shifted to an appropriate level, enabling each power agent to detect the uncertainty conditions, and subsequently to determine its operation modes based on the DCV levels. Simulation and experimental results under different test conditions confirm the reliability and effectiveness of the proposed control scheme.

The gut plays a key role in drug absorption and metabolism of orally ingested drugs. Additionally, characterization of intestinal disease processes are increasingly gaining more attention as gut health is an important contributor to our overall health. The most recent innovation to study intestinal processes in vitro is the development of gut-on-a-chip (GOC) systems. Compared to conventional in vitro models they offer more translational value, and many different GOC models have been presented over the past years. Here, we reflect on the almost unlimited choices in designing and selecting a GOC for preclinical drug (or food) development research. Four components that largely influence the GOC design are highlighted, namely 1) the biological research questions, 2) chip fabrication and materials, 3) tissue engineering, and 4) the environmental and biochemical cues to add or measure in the GOC. Examples are presented of GOC studies in the two major areas of preclinical intestinal research: 1) intestinal absorption and metabolism to study the oral bioavailability of compounds, and 2) treatment-orientated research for intestinal diseases. The last section of this review presents an outlook on the limitations to overcome in order to accelerate preclinical GOC research.

This study aims to construct simple devices to ascertain the concentrations of ammonium (NH4+) and nitrate (NO3-). The device structure comprises a visible and near-infrared absorption meas-urement room, along with an RGB (red, green, and blue) absorption measurement room, con-stituting the two measuring rooms. Both the measurement rooms are equipped with light sources and detectors configured to operate in opposed or thru-beam modes. A tiny processor is utilized for processing the measurements, with an algorithm implemented within its memory. During the algorithm development phase, ranges for measuring the quantity of nutrients were categorized using a discriminant analysis approach. Thirty percent of the soil sample data were utilized as verification data, while the remaining 70 percent served as training data. Nutrient content values from reliable measuring instruments were incorporated into all datasets. Discriminant analysis was employed to classify the amount of NH4+ into five ranges based on the test results. When tested with soil samples, the accuracy was 66.13% compared to the reference value of a reliable measuring device. Similarly, NO3- was classified into four ranges with an accuracy of 81% com-pared to the reference value of a reliable measuring device.

The influence of growth temperature on the crystalline quality and optical properties of AlGaN at 325 nm, grown using plasma-assisted molecular beam epitaxy (MBE), was investigated. The growth temperature exhibited a significant impact on the growth mode and surface morphology. Specifically, at a growth temperature of 750 degrees Celsius, when appropriate Al and Ga flow rates were employed, the AlGaN layer exhibited exceptional surface morphology and favorable optical properties. The optical properties of the AlGaN material were explored, revealing the presence of two distinct non-radiative recombination centers characterized by different activation energies. The minority carrier lifetimes were measured as 560 ps at 10 K and 64 ps at room temperature. The underlying mechanism was analyzed from the perspective of carrier dynamics, shedding light on the observed phenomena.

The application of artificial intelligence to point-of-care testing (POCT) disease detection has become a hot research field, in which breath detection which detects the patient's exhaled VOCs combined with sensor arrays of Convolutional Neural Network (CNN) algorithms as a new lung cancer detection is attracting more researchers' attention. However, due to low accuracy, high complexity computation and large number of parameters make the CNN algorithms difficult transplant to the embedded system of POCT devices. A lightweight neural network (LTNet) in this work is proposed to deal with this problem, and meanwhile, achieve high-precision classification of acetone and ethanol gases, which are respiratory markers for lung cancer patients. Compared to currently popular lightweight CNN models such as EfficientNet, LTNet has fewer parameters (32K) and its training weight size is only 0.155 MB. LTNet achieved an overall classification accuracy of 99.06% and 99.14% in the own mixed gas dataset and the University of California (UCI) dataset, which are both higher than that of the five existing models’, and it also offers the shortest training (844.38s and 584.67s) and inference time (23s and 14s) in the same validation set. Compared to the existing CNN models, LTNet is more suitable for resource-limited POCT devices.

Scientists can use the Clustered regularly interspaced short palindromic repeats (CRISPR)/CRISPR-associated (Cas) protein 9 system, which is a powerful and flexible tool for changing the genome, to change only certain parts of the genome. This has helped researchers figure out how target genes work in biology and disease. CRISPR/Cas9 is made up of a sequence-specific CRISPR RNA (crRNA) set and a generic Cas9 nuclease. The crRNA set tells Cas9 where to cut DNA and cause double-strand breaks. In the next step of cellular DNA repair, insertions, deletions, and swaps are made at specific spots. For CRISPR/Cas9-mediated DNA cleavage to be specific, the target sequences must match the crRNA, and a protospacer nearby motif must be placed after the target sequences. In this article, we talk about how CRISPR/Cas9 works at the molecular level, what it can be used for, what it can't do, and what its future clinical treatment promise might be.

This paper focuses on optimal sensor positioning for monitoring activities of daily living and investigates different combinations of features and models on different sensor positions, i.e., the side of the waist, front of the waist, chest, thigh, head, upper arm, wrist, and ankle. Sixteen features are extracted and the feature importance is measured by using the Relief-F feature selection algorithm. Eight classification algorithms are evaluated on a dataset collected from young subjects and that collected from elderly subjects, with two different experimental settings. To deal with different sampling rates, signals with a high data rate are down-sampled and a transformation matrix is used for aligning signals to the same coordinate system. The thigh, chest, side of the waist, and front of the waist are the best four sensor positions for the first dataset (young subjects), with average accuracy values being greater than 95%. The best model obtained from the first dataset for the side of the waist is validated on the second dataset (elderly subjects). The most appropriate number of features for each sensor position is reported. The results provide a reference for building activity recognition models for different sensor positions, as well as for data acquired from different hardware platforms and subject groups.

Optical artificial neural networks (ONNs) — analog computing hardware tailored for machine learning [1,2] — have significant potential for ultra-high computing speed and energy efficiency [3]. We propose a new approach to architectures for ONNs based on integrated Kerr micro-comb sources [4] that is programmable, highly scalable and capable of reaching ultra-high speeds. We experimentally demonstrate the building block of the ONN — a single neuron perceptron — by mapping synapses onto 49 wavelengths of a micro-comb to achieve a high single-unit throughput of 11.9 Giga-FLOPS at 8 bits per FLOP, corresponding to 95.2 Gbps. We test the perceptron on simple standard benchmark datasets — handwritten-digit recognition and cancer-cell detection — achieving over 90% and 85% accuracy, respectively. This performance is a direct result of the record small wavelength spacing (49GHz) for a coherent integrated microcomb source, which results in an unprecedented number of wavelengths for neuromorphic optics. Finally, we propose an approach to scaling the perceptron to a deep learning network using the same single micro-comb device and standard off-the-shelf telecommunications technology, for high-throughput operation involving full matrix multiplication for applications such as real-time massive data processing for unmanned vehicle and aircraft tracking.

Gravity played an important role in the development of life on earth. The effect of gravity on a living organisms can be investigated by controlling the magnitude of gravity. Most reduced gravity experiments are conducted on the lower earth orbit (LEO) in the International Space Station (ISS). However, running experiments in ISS face challenges such as high cost, extreme condition, lack of direct accessibility, and long waiting period. Therefore, researchers have developed various ground-based devices and methods to perform reduced gravity experiments. However, the search for life outside the earth requires more intensive research. Advancements in conventional methods and the development of new tools are required for this purpose. The advantages of Lab-on-a-Chip (LOC) devices make them an attractive option for simulating microgravity. This paper briefly reviews the advancement of LOC technologies for simulating microgravity in a earth-based laboratory.

Background: Elevated respiratory rates (RR) have been described in several disease states, such as pneumonia, asthma and bronchiolitis. Despite this, there are few studies defining the range of RR found in healthy children. Available age percentiles for RR have been generated using methods that have the potential themselves to alter the rate. Aim: The aim of this study was to develop accurate percentile charts of RR specific for age in healthy children for potential use in pre-hospital care (first-aid), clinical medicine and for reference in respiratory research. Method: A newly developed optical respiratory sensor was used to measure RR which placed no restrictions on respiratory excursion. This technique enabled recording in awake children without the artefact of the observer’s presence on the subject’s RR. A cross-sectional sample of healthy children was obtained from maternity wards, childcare centres and schools in Brisbane, Queensland, Australia. Results: RR were observed in 560 awake and 103 sleeping children of which data from 343 awake and 94 sleeping children was used to create reference ranges for healthy children from newborn to 13 years of age. The recorded rates were significantly higher when children were awake compared to asleep. During quiet sleep, RR decreased from 40 (interquartile range 7) bpm at one month to 20 (interquartile range 3) in children aged 3 years. In awake children, RR ranged from a median of 40 bpm (interquartile range 18) at 1 year to 12 bpm (interquartile range 11) at 13 years respectively. Conclusion: The optical sensor was found to be an appropriate respiratory transducer, capable of measuring RR and reducing artefact by the subjective responses of alert children. The centile charts will be helpful as an aid to detecting abnormal RR in children and will contribute to further systematic reviews related to this vital sign.

Metabarcoding of prokaryotic and fungal ribosomal DNA was used to describe the microbial communities in soils of remnant equatorial rainforest, maize-bean intercrop, and sugarcane in western Kenya. Cropping systems influenced the microbial community composition and functional traits (energy source and nutrient cycling) of bulk soil in each crop. Microbial richness and diversity tended to increase with cultivation intensity. Soil of maize-bean intercrop had lower percentages and sugarcane had higher percentages of unique amplicon sequence variants of both bacteria and fungi compared to the remnant forest. Functional traits were altered by cultivation intensity. Compared to remnant forest soils, maize-bean intercrop soil had lower percentages of aerobic chemoheterotrophic bacteria and higher percentages of N-cycling bacteria, while sugarcane had higher percentages of aerobic chemoheterotrophic bacteria and lower percentages of N-cycling bacteria. In the face of increasing forest loss and pressures for agricultural productivity, this landscape provides a rich site for studying the impacts of cropping systems on soil health.

Cutaneous wound healing is a complex multi-stage process involving direct and indirect cell communication events with the aim of efficiently restoring the barrier function of the skin. One key aspect in cutaneous wound healing is associated with cell movement and migration into the physically, chemically and biologically injured area resulting in wound closure. Understanding the conditions under which cell migration is impaired and elucidating the cellular and molecular mechanisms that improve healing dynamics is therefore crucial in devising novel therapeutic strategies to elevate patient suffering, reduce scaring and eliminate chronic wounds. Following the global trend towards automation, miniaturization and integration of cell-based assays into microphysiological systems, conventional wound healing assays such as the scratch assay or cell exclusion assay have recently been translated and improved using microfluidics and lab-on-a-chip technologies. These miniaturized cell analysis systems allow precise spatial and temporal control over a range of dynamic microenvironmental factors including shear stress, biochemical and oxygen gradients to create more reliable in vitro models that resemble the in vivo microenvironment of a wound more closely on a molecular, cellular, and tissue level. The current review provides (a) an overview on the main molecular and cellular processes that take place during wound healing, (b) a brief introduction into conventional in vitro wound healing assays, and (c) a perspective on future cutaneous and vascular wound healing research using microfluidic technology.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

Theoretical studies on the generation of nondiffracting and nondispersive light pulses and their experimental implementation are one of the renowned problems within electromagnetics. Current technologies enable creation of short-duration pulses of a few cycles with high power and fluency. An application of these techniques to the field of nondiffracting and nondispersive pulses requires a proper mathematical description of highly focused vector pulses. In this work, we study vector optical bullets in a dielectric medium with different polarization structures: linear, azimuthal, and radial. We report the differences caused by the vector model compared to the scalar model. We analyze effects caused by superluminal, subluminal, or even negative group velocity on properties of vector optical bullets inside a dielectric material.

Immunosenescence refers to age-related alterations of the immune system function affecting both the humoral and cellular arm of immunity. Understanding immunosenescence and its impact on vaccination of older adults is essential since primary vaccine responses in older individuals can fail to generate complete protection, especially vaccines targeting infections with increased incidence among the elderly, such as the respiratory syncytial virus. Here, we review the clinical trials of both candidate and approved vaccines against respiratory syncytial virus (RSV), which include adults aged ≥50 years, with an emphasis on the evaluation of immunogenicity parameters. Currently, there are 10 vaccine candidates and 2 vaccines approved for the prevention of RSV in the older adult population. The number of registered clinical trials for this age group amounts to 32. Our preliminary evaluation of published results and interim analyses of the RSV vaccine clinical trials indicates efficacy in older adult participants, demonstrating immunity levels that closely resemble those of younger adult participants.

The study of the impact of polyQ expansion driven proteotoxicity on cell metabolism has evi-denced NAD molecule as a central player in regulating metabolic response and cell repair in neurodegeneration. The decline in NAD intracellular levels represents a hallmark of ageing aris-ing from a dysregulation between NAD-consuming and biosynthetic enzymatic reactions in which NMNAT plays a key role. By an integrated bioanalytical and proteomic experimental design, the derangement of NAD metabolism deriving from the accumulation of polyQ-Htt protein has been analysed in Saccha-romices cerevisiae harbouring a 103Q-Htt and compared with wild-type Htt, in absence and in presence of a phenolic extract from EVOO, as a source of antioxidant bioactive compounds. Quantification of NAD and its precursors and proteomic analysis of the differential protein ex-pression has been performed by LC-DAD-MS. Chronological lifespan and NAD homeostasis was strongly impaired by proteotoxic polyQ-Htt, eliciting a depletion of NAD levels and accumulation of NaMN. In parallel a downregulation of Sirt2 expression levels has been observed. Phenolic extract administration had no meaningful ef-fects on NAD replenishment to prevent proteotoxicity. NaMN can represent a biomarker of accel-erated aging, and/or a signaling molecule for cell repair.

This paper investigates an Energy Neutral System using Micro Energy Harvesters for a Health Monitoring Wireless Sensor Node (HM-WSN). We have implemented HM-WSN consisting of a solar cell energy harvester, a Power Management Unit (PMU) and the ucontroller, sensor and transmitter acting as load. A battery extender and a switching logic circuit for sensor node is designed to evaluate the efficiency of the proposed system. The HM-WSN senses body temperature with improvement in lifetime of coincell. The HM-WSN is built using commercially available off the shelf (COTS components and consumes 47.2uW for data being updated every 134s. It can be operated for approximately 1.32 years only on a coincell. Furthermore, the HM-WSN can be operated with solar energy at 200lux, achieving 96.36 years with a combination of a coincell with an additional capacitor of 2.2mF. It attains 4.07 years to 16.87 years lifetime with the load capacitor varying from 1mF to 1.5mF at 350lux lighting condition. With the same ambient condition and a 2mF load capacitor, HM-WSN attains complete energy autonomy.

This paper proposed emotion recognition methods for consecutive facial images, and implements the inference of neural network model on a field-programmable gate array (FPGA). The proposed emotion recognition methods are based on a neural network model architecture that combines convolution neural networks (CNNs), long short-term memory (LSTM), and fully connected neural networks (FCNNs), called CLDNN or ConvLSTM-FCN. This type of neural network mod-el can analyze the local feature sequences obtained through convolution of data, making it suita-ble for processing time-series data such as consecutive facial images. In this paper, sequences of facial images are sampled from videos corresponding to various emotional state of subjects. The sampled images are then pre-processed with the processes includes facial detection, greyscale conversion, resize, and data augmentation if necessary. The 2-D CNN in ConvLSTM-FCN is used for feature extraction for these pre-processed facial images. These sequences of facial im-age features are time sequences with dependent properties between the elements within them. The LSTM is then used to model these time sequences followed by fully connected neural net-works (FCNNs) for classification. The proposed consecutive facial emotion recognition method achieves an average recognition rate of 99.51% on RAVDESS dataset, 87.80% on BAUM-1s dataset and 96.82% on eNTERFACE’05 data set, using 10-fold cross-validation on the PC. Some com-parisons of recognition accuracies between the proposed method and the other existing related works are conducted in this paper. According to the comparisons, the proposed emotion recog-nition methods outperform the existing related researches. The proposed emotion recognition methods are then implemented on an FPGA chip using the neural network model inference algo-rithms in this paper, and the accuracies of the experiments conducted on the FPGA chip are iden-tical to those obtained on the PC. This verifies that the proposed neural network model imple-mented on the FPGA chip performs well.

The chiral optical Tamm state (COTS) is a special localized state at the interface of a handedness-preserving mirror and a structurally chiral medium such as a cholesteric liquid crystal or a chiral sculptured thin film. The spectral behavior of COTS, observed as reflection resonances, is described by the temporal coupled-mode theory. Mode coupling is different for two circular light polarizations because COTS has a helix structure replicating that of the cholesteric. The mode coupling for co-handed circularly polarized light exponentially attenuates with the cholesteric layer thickness since the COTS frequency falls into the stop band. Cross-handed circularly polarized light freely goes through the cholesteric layer and can excite COTS when reflected from the handedness-preserving mirror. The coupling in this case is proportional to anisotropy of the cholesteric and theoretically it is only anisotropy of magnetic permittivity that can ultimately cancel this coupling. These two couplings being equal results in a polarization crossover (the Kopp--Genack effect) for which a linear polarization is optimal to excite COTS. The corresponding cholesteric thickness and scattering matrix for COTS are generally described by simple expressions.

Dermal water content is an important biophysical parameter in preserving skin integrity and preventing skin damage. Traditional electrical-based and open-chamber evaporimeters have several well-known limitations. In particular, such devices are costly, sizeable, and only provide arbitrary outputs. They also do not permit continuous and non-invasive monitoring of dermal water content, which can be beneficial for various consumer, clinical and cosmetic purposes. We report here on the design and development of a digital multi-wavelength optical sensor that performs continuous and non-invasive measurement of dermal water content. In-silico investigation on porcine skin was carried out using the Monte Carlo modelling strategy to evaluate the feasibility and characterise the sensor. Subsequently, an in-vitro experiment was carried out to evaluate the performance of the sensor and benchmark its accuracy against a high-end, broad band spectrophotometer. Reference measurements were made against gravimetric analysis. The results demonstrate that the developed sensor can deliver accurate, continuous, and non-invasive measurement of skin hydration through measurement of dermal water content. Remarkably, the novel design of the sensor exceeded the performance of the high-end spectrophotometer due to the important denoising effects of temporal averaging. The authors believe, in addition to wellbeing and skin health monitoring, the designed sensor can particularly facilitate disease management in patients presenting diabetes mellitus, hypothyroidism, malnutrition, and atopic dermatitis.

In this paper, a method is developed for presenting a novel virtual torque sensor based on precise model and position measurements avoids the need of traditional strain gauges and amplifiers. More specifically, the harmonic drive compliance model and the Gaussian process regression (GPR) technique are used together to achieve virtual torque sensor measurement. While the harmonic drive compliance model provides the analytic part, the Gaussian process regression method is used to reconstruct the unmolded part based on motor-side and link-side joint angles as well as motor current. After an automatic offline calibration, the method allows for a lean online implementation. The virtual torque sensor measurement is compared with measurements of a commercial torque sensor, and the results have attested the effectiveness of the proposed method.

Over the last two decades, microfluidics has received significant attention from both academia and industry, and researchers report thousands of new prototype devices each year for use in a broad range of environmental, pharmaceutical, and biomedical engineering applications. While lab-on-a-chip fabrication costs have continued to decrease, the hardware required for monitoring fluid flows within microfluidic devices themselves remains expensive and often cost prohibitive for researchers interested in starting a microfluidics project. As microfluidic devices become capable of handling complex fluidic systems, low-cost, precise and real time pressure and flow rate measurement capabilities has become increasingly important. While many labs use commercial platforms and sensor, these solutions can often cost thousands of dollars and can be too bulky for on-chip use. Here we present a new inexpensive and easy -to-use piezoresistive pressure and flow sensor that can be easily integrated into existing on-chip microfluidic channels. The sensor consists of PDMS-Carbon black conductive membranes and uses an impedance analyzer to measure impedance change due fluid pressure. The sensor costs several orders of magnitude less than existing commercial platforms and can monitor local fluid pressures and calculate flow rates based on pressure gradient.

The role of circulating plasma cells (CPCs) and circulating leukemic cells (CLCs) as biomarkers for several blood cancers, such as multiple myeloma and leukemia, respectively, have recently been reported. These markers can be attractive due to the minimally invasive nature of their acquisition through a blood draw (i.e., liquid biopsy) negating the need for painful bone marrow biopsies. CPCs or CLCs can be used for cellular/molecular analyses, such as immunophenotyping or fluorescence in situ hybridization (FISH). FISH, which is typically carried out on slides involving complex workflows, becomes problematic when operating on CLCs or CPCs due to their relatively modest numbers. Here, we present a microfluidic device for characterizing CPCs and CLCs enriched from peripheral blood using immunofluorescence or FISH. The microfluidic possessed an array of cross-channels (2-4 µm in depth and width) that interconnected a series of input and output fluidic channels. Placing a cover plate over the device formed microtraps, the size of which was defined by the width and depth of the cross-channels. This microfluidic chip allowed for automating immunofluorescence and FISH requiring the use of small volumes of reagents, such as antibodies and probes, as compared to slide-based immunophenotyping and FISH. In addition, the device could secure FISH results in <4 h compared to 2-3 d for conventional FISH.

Aim: The aim of this study was to investigate if tests used to assess core stability could be used to determine success in physiological tests applied to assess dynamic balance and agility for a young active population. Methods: Pearson's r correlation coefficient was used to assess the relationship between the core stability tests and the dynamic balance and agility tests. Evaluation of the tests was established using Cronbach's coefficient of variance as part of intra-rater reliability tests. An analysis of 18 active college aged students was conducted (males: n= 13, females: n= 5). The mean ± SD age for males was 19.2 years ± 3.22 years and for females was 19.4 years ± 1.14 years. Conclusion: The results indicate that there is no significant relationship between tests that assess core stability and tests conducted to assess dynamic balance in active young adults. With the exception of the abdominal flexion test, no significant relationship exists between the remaining core stability tests and agility T-Test. Core stability is not a determinant of balance and agility.

Monarch butterflies are a species of conservation priority due to declining overwintering populations in both eastern and western North America. Declines in western overwintering monarchs—more than 99% since monitoring began—are especially acute. However, the degree to which the western monarch is a distinct biological entity is uncertain. In this review, we focus on phenotypic and genetic differentiation between eastern and western monarchs, with the goal of informing researchers and policy-makers who are interested in monarch conservation. Eastern and western monarchs occupy distinct environments and show some evidence for phenotypic differentiation—particularly for migration-associated traits—though population genetic and genomic studies suggest that they are genetically indistinguishable from one another. We suggest future studies that could improve our understanding of differences between eastern and western monarchs. We also discuss the concept of adaptive capacity in eastern and western monarchs as well as non-migratory populations outside of the monarch’s primary North American range.

Wavelength selective switches (WSSs) are essential elements for wavelength division multiplexing (WDM) optical networks, as they offer cost-effective, high port-count and flexible spectral channel switching. This work proposes a new hybrid WSS architecture that leverages the beam shaping and steering features of uniform silicon nitride (SiN) based end-fire optical phased arrays (OPAs). By introducing beamforming to a WSS system, the spectral channels on the liquid crystal on silicon (LCoS) panel can be tailored and arranged properly, depending on the optical configuration, using the beam control capabilities of OPAs. Combining 3D-FDTD and ray tracing simulations, the study shows that by reducing the input beam dimensions with proper sizing of the OPAs, the WSS design with the null-steering OPAs layout and 4×No switch size features increased spectral resolution. This extensive beamforming study on the steering-enabled layout reveals the acquirement of an even higher input channel number, achieving up to the 8×No WSS scheme with flexible channel routing on the LCoS panel. Such implementation of beamsteerers can unlock an extra degree of freedom for the switching capabilities of hybrid WSS devices. The results show great promise for the introduction of OPAs in WSS systems and provide valuable insight for the design of future wireless communication links and WDM systems.

Real-time multi-axis distributed tactile sensing is a critical capability if robots are to perform stable gripping and dexterous manipulation, as it provides crucial information about the sensor-object interface. In this paper, we present an optical-based 6-axis tactile sensor designed in a fingertip shape for robotic dexterous manipulation. The distributed sensor can precisely estimate local XYZ force and displacement at ten distinct locations, and provide global XYZ force and torque measurements. Its compact size, comparable to that of a human thumb, and minimal thickness allow seamless integration onto existing robotic fingers, eliminating the need for complex modifications to the gripper. The proposed sensor design uses a simple, low-cost fabrication method. Moreover, the optical transduction approach uses light angle and intensity sensing to infer force and displacement from deformations of individual sensing units that form the overall sensor, providing distributed 6-axis sensing. The local force precision at each sensing unit in the X, Y, and Z axes is 20.89 mN, 19.19 mN, and 43.22 mN, respectively, over an local force range of approximately ±1.5 N in X and Y and 0 to -2 N in Z. The local displacement precision in the X, Y and Z axes is 56.70 μm, 50.18 μm and 13.83 μm, respectively, over a local displacement range of ±2 mm in the XY directions and 0 to -1.5mm in Z (i.e., compression). Additionally, the sensor can measure global torques, Tx, Ty and Tz, with a precision of of 1.90 N-mm, 1.54 N-mm and 1.26 N-mm, respectively. The fabricated design is showcased by integrating it with an OnRobot RG2 gripper and illustrating real-time measurements during in simple demonstration task which generate changing global forces and torques.

A 3D graphene foam made of interconnected multilayer graphene flakes was produced on optical fibres (OF) by laser-induced transformation of a polyimide (PI) film coated on the OF cladding. This material, known as la-ser-induced graphene (LIG), was explored in the electrochemical detection and quantification of dopamine (DA) at physiologically relevant concentrations in the presence of the most relevant interfering molecules in biological fluids, ascorbic acid (AA) and uric acid (UA). The measured limit of detection is 100 nM, the linear range is 0.1 to 5 μM and a maximum sensitivity of 5.0 µA µM−1 cm−2 was obtained for LIG decorated with Pt nanoparticles (NPs). Moreover, immunity to AA and UA interference and to fouling was attained by decorating the LIG elec-trode with Pt NPs and coating with Nafion. These figures of merit underlines the potential of these sensors for the quantification of physiologically relevant concentrations of DA in biological fluids, paving the way for the development of hybrid electrochemical/optical sensing actuating platforms in a lab-on-fibre configuration, with relevant applications in biomedical engineering. The advantages of this hybrid arrangement include the possi-bility of in-situ counterproofing, extended measuring ranges, photoelectrochemical detection and the probing of inaccessible places. This elegant approach can also provide a simple and cost-effective way to fabricate biomed-ical devices with extended functionality, such as medical optical probes with added electrochemical capabilities, optogenetics combined with local electrochemical detection, among others.

Herein, we offer a numerical study on the devising of a unique 2D-heterostructure Photonic crystal (PC) that can split two orthogonally polarized light waves. The analysis is performed via a two-dimensional finite element method (2D-FEM) by utilizing COMSOL Multiphysics software. The device consists of two discrete designs of PC formation. The first PC formation is optimized so that it permits both TE and TM-polarization of light to transmit through it. Whereas the second PC formation possesses a Photonic Bandgap (PBG) only for TE-polarized light. These two formations are combined at an angle of 45 degrees, resulting in a reflection of self-collimated TE-polarized light at an angle of 90 degrees owing to the PBG present in the second PC formation. While permitting the self-collimated TM-polarized light wave to travel uninterrupted. The proposed device has a small footprint of ~10.5 μm2 offering low transmission loss and high polarization extinction ratio which makes it an ideal candidate to be employed as an on-chip polarization division multiplexing system.

Nowadays, unmanned vehicles are widely used in various fields. However, the safety of unmanned vehicles is directly determined by the autopilot systems, and sensor faults are a very critical factor that affects the normal operation of the autopilot systems. To efficiently and comprehensively test unmanned systems for sensor faults, this paper proposes a chip-level testing platform for unmanned vehicle autopilot systems based on FPGA hardware-in-the-loop simulation. Unlike existing testing platforms, the introduction of FPGA technology allows us to achieve nanosecond real-time simulation frequency, thus realizing chip-level simulation of sensors and black-box automated testing. Firstly, we propose a set of general platform and modeling methods, and the paper presents a detailed application of the four most common necessary sensors in autopilot systems as examples. Secondly, we propose for the first time a chip-level fault testing method for unmanned systems, and build a test platform with a quadrotor vehicle, the PX4 software platform, and the Pixhawk4 hardware platform as examples. Finally, the experimental results verify that the testing platform proposed in this paper can adapt to various autopilot systems and has high simulation test reliability.

The existence of low-cost and accurate tools that can equip the First Responders (FRs) to detect trapped victims and provide insights about their health condition in the aftermath of a disaster, is imperative. To address the problem of detecting trapped victims behind walls or debris, we have developed a tool that exploits an Ultra-Wide Band (UWB) radar sensor for data collection and Machine Learning (ML) algorithms for data analysis. To evaluate the efficacy of our approach, we collected data from nine humans, both in standing and lying down positions. Next, we applied various ML algorithms to the collected dataset for two discrete sub-tasks that are of interest from an FR’s perspective. The first task is the detection of the victim’s presence, where the algorithms attained more than 95% accuracy and F1-Score. The second task is the estimation of the distance between the radar sensor and the victim, where the tool showed an average error of less than 40 cm.

We propose a method for creating parallel Bessel-like vortical optical needles with an arbitrary axial intensity distribution via superposition of different cone-angle Bessel vortices. We analyze the interplay between the separation of individual optical vortical needles and their respective lengths and introduce a super-Gaussian function as their axial profile. We also analyze the physical limitations to observe well-separated optic needles, as they are influenced by mutual interference of the individual beams. To verify our theoretical and numerical results, we generate controllable spatial arrays of individual Bessel beams with various numbers and spatial separations by altering the spectrum of the incoming laser beam via the spatial light modulator. We demonstrate experimentally how to implement such beams using a diffractive mask. The presented method facilitates the creation of diverse spatial intensity distributions in three dimensions, potentially finding applications in specific microfabrication tasks or other contexts. These beams may have benefits in laser material processing applications such as nanochannel machining, glass via production, modification of glass refractive indices, and glass dicing.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

Domain-specific systems-on-chip (DSSoCs) aim to narrow the gap between general-purpose processors and application-specific designs. CPU clusters enable programmability, while hardware accelerators tailored to the target domain minimize task execution times and power consumption. Traditional operating system (OS) schedulers can diminish the potential of DSSoCs as their execution times can be orders of magnitude larger than the task execution time. To address this problem, we propose a dynamic adaptive scheduling (DAS) framework that combines the advantages of a fast, low-overhead scheduler and a sophisticated, high-performance scheduler with a larger overhead. We present a novel runtime classifier that chooses the better scheduler type as a function of the system workload, leading to improved system performance and energy-delay product (EDP). Experiments with five real-world streaming applications indicate that DAS consistently outperforms fast, low-overhead, and slow, sophisticated schedulers. DAS achieves a 1.29x speedup and 45% lower EDP than the sophisticated scheduler under low data rates and a 1.28x speedup and 37% lower EDP than the fast scheduler when the workload complexity increases. Furthermore, we demonstrate that the superior performance of the DAS framework also applies to hardware platforms, with up to a 48% and 52% reduction in execution time and EDP, respectively.

Climate simulations in West Africa have been attributed with large uncertainties. Global climate projections are not consistent with changes in observations at the regional or local level of the Niger basin, making management of hydrological projects in the basin uncertain. This study evaluates the potential of using the quantile mapping bias correction to improve the Coupled Model Intercomparison Project (CMIP5) outputs for use in hydrology impact studies. Rainfall and temperature projections from 8 CMIP5 Global Climate Models (GCM) were bias corrected using the quantile mapping approach. Impacts of climate change was evaluated with bias corrected rainfall, temperature and potential evapotranspiration (PET). The IHACRES hydrological model was adapted to the Niger basin and used to simulate impacts of climate change on discharge under present and future conditions. Bias correction significantly improved the accuracy of rainfall and temperature simulations compared to observations. Nash coefficient (NSE) for monthly rainfall comparisons of 8 GCMs to the observed was improved by bias correction from 0.69 to 0.84. The standard deviations among the 8 GCM rainfall data were significantly reduced from 0.13 to 0.03. Increasing rainfall, temperature, PET and river discharge were projected for all GCMs used in this study under the RCP8.5 scenario. These results will help improving projections and contribute to the development of sustainable climate change adaptation strategies.

After UV excitation, gas phase thymine returns to ground state in 5 to 7 ps, showing multiple time constants. There is no consensus on the assignment of these processes, with a dispute between models claiming that thymine is trapped either in the first (S1) or in the second (S2) excited states. In the present study, nonadiabatic dynamics simulation of thymine is performed on the basis of ADC(2) surfaces, to understand the role of dynamic electron correlation on the deactivation pathways. The results show that trapping in S2 is strongly reduced in comparison to previous simulations considering only non-dynamic electron correlation on CASSCF surfaces. The reason for the difference is traced back to the energetic cost for formation of a CO p bond in S2.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

Human Activity Recognition (HAR) technology enables continuous behavior monitoring, particularly valuable in healthcare. This study investigates the viability of using an ear-worn motion sensor for classifying daily activities, including lying, sitting/standing, walking, ascending stairs, descending stairs, and running. Fifty healthy participants (between 20 and 47 years old) engaged in these activities while under monitoring. Various machine learning algorithms, ranging from interpretable shallow models to state-of-the-art deep learning approaches designed for HAR, were employed for classification. Results demonstrate the ear sensor's efficacy, with deep learning models achieving 98% accuracy rate of classification. The obtained classification models are agnostic regarding which ear the sensor is worn and robust against moderate variations in sensor orientation (e.g., due to differences in auricle anatomy), meaning no initial calibration of the sensor orientation is required. The study underscores the ear's efficacy as a suitable site for monitoring human daily activity and suggests its potential for combining HAR with in-ear vital signs monitoring. This approach offers a practical method for comprehensive health monitoring by integrating sensors in a single anatomical location. This integration facilitates individualized health assessments, with potential applications in tele-monitoring, personalized health insights, and optimizing athletic training regimes.

In this study, a novel flexible ethanol gas sensor was created by the deposition of CoFe2O4 (CFO) thin film was on a thin mica substrate using pulsed laser deposition. Transition electron microscopy (TEM) investigations clearly demonstrated the successful growth of CFO on the mica, where a well-defined interface was observed. Ethanol gas-sensing studies showed optimal performance at 200 °C, with the highest response, 19.2, to 100 ppm ethanol. Operating the sensor in self-heating mode under 7 V applied voltage, which was corresponds to a temperature of approximately 200 °C, produced a maximal response to ethanol of 19.2. This aligned with the highest responses observed during testing at 200 °C, confirming the sensor’s accuracy and sensitivity to ethanol under self-heating conditions. In addition, the sensor exhibited good selectivity to ethanol and excellent flexibility; maintaining its high performance after bending and tilting up to 5000 times. As this is the first report on flexible self-heated CFO gas sensors, we believe that this research holds great promise for the future development of high-quality sensors based on this approach.

We report the relative humidity (R.H.) sensing response of a resistive sensor, employing sensing layers based on a ternary nanohybrid comprising holey carbon nanohorns (CNHox), potassium chloride (KCl), and polyvinylpyrrolidone (PVP) at mass ratios 7/1/2, 6.5/1.5/2, and 6/2/2 (w/w/w/w). The sensing structure comprises a silicon substrate, a SiO2 layer, and interdigitated transducer (IDT) electrodes. The sensing film is deposited on the sensing structure via the drop-casting method. The sensing layers' morphology and composition are investigated through Scanning Electron Microscopy (S.E.M.) and RAMAN spectroscopy. The ternary hybrid-based thin film resistance increases when the sensors are exposed to R.H., ranging from 0% to 100%. The manufactured devices show a room temperature response comparable to a commercial capacitive R.H. sensor and are characterized by excellent linearity, rapid response time, and good sensitivity. The presented sensors exhibit superior performance in terms of sensitivity compared to other similarly manufactured and tested sensors that employ a CNHox-based sensing layer. We explain the sensing role of each constituent of the ternary hybrid nanocomposites based on their chemical and physical properties, electronic properties, and affinity for water molecules. Different alternative sensing mechanisms are considered and discussed, such as the decreasing number of holes in the holey CNHox at the interaction with water molecules, proton conduction, and PVP swelling.

Organ-on-a-chip (OOC) is an emerging technology that simulates an artificial organ within a microfluidic cell culture chip. Current cell biology research focuses on in vitro cell culture due to various limitations of in vivo testing. Unfortunately, in vitro cell culture fails to provide an accurate microenvironment, and in vivo cell culture is expensive and has historically been a source of ethical controversy. OOC aims to overcome these shortcomings and provide the best of both in vivo and in vitro cell culture research. The key component of the OOC design is utilizing microfluidics to ensure a stable concentration gradient, dynamic mechanical stress modeling, and accurate reconstruction of a cellular microenvironment. OOC also has the advantage of complete observation and control of the system, which is impossible to recreate in in vivo research. Multiple throughputs, channels, membranes, and chambers are constructed in a polydimethylsiloxane (PDMS) array to simulate various organs on a chip. Various experiments can be performed utilizing OOC technology, including drug delivery research and toxicology. Current technological expansions involve multiple organ microenvironments on a single chip, allowing for studying inter-tissue interactions. Other developments in the OOC technology include finding a more suitable material as a replacement for PDMS and minimizing artefactual error and non-translatable differences.

This study compared the use of chip and slash to minimize the loss of sediment on newly constructed forest road slopes and investigated the annual amount of sediment loss on bare forest road slopes. A runoff block (sample field) was established for each of the four designated test sites (two cutslopes and two fillslopes). Each block had three runoff plots. One of the runoff plots was left empty for the control (CNT), while chip (C) and slash (S), respectively, were deposited in the other two. A total of 108 water samples were taken from the test sites and the amount of their suspended sediment calculated in the laboratory. As a result of this study, it was determined that the amount of soil loss in the control plots was about 1.26 times higher than in the slash plots and 2.21 times higher than in the chip plots. According to the results of variance analysis on the amounts of sediment, a statistically significant difference was found between the suspended sediment quantities transported on the road slopes (P <0.05). However, no statistically significant difference between the suspended sediment quantities transported in the plots and the other variables of aspect, gradient or road slope was revealed by the t-test (P >0.05).

This work introduces a neuromorphic sensor based on force-sensing resistors (FSR) and spiking neurons for robotic systems. The proposed sensor integrates the FSR in the schematic of spiking neuron in order to make the sensor to generate spikes with frequency that depends on the applied force. The performance of the proposed sensor is evaluated for the control of a SMA-actuated ro-botic finger by monitoring the force during steady state when the finger pushes on a tweezers. For comparison purposes, we performed similar evaluation when the SNN receives input from a widely used compression load cell (CLC). The results show that the proposed FSR based neuro-morphic sensor has very good sensitivity to low forces and the function between the spiking rate and the applied force is continuous with good variation range. However, when compared to the CLC, the proposed sensor has lower linearity of the response, but it benefits from two orders of magnitude lower power consumption. These aspects imply that the neuromorphic sensor based on FSR are useful for bioinspired control of humanoid robotics representing a low power and low cost alternative the widely used sensors.

Glioblastoma (GBM) is one of the most aggressive solid tumors, particularly due to the presence of cancer stem cells (CSCs). Today the characterization of this type of cells with an efficient, fast and low-cost method remains an issue. Hence, we have developed a microfluidic lab-on-a-chip based on dielectrophoresis (DEP) single cell electro-manipulation to measure the two crossover frequencies: f_x01 in low frequency range (below 500 kHz) and f_x02 in Ultra High Frequency range (UHF, above 50 MHz). First, in vitro conditions were investigated. U87-MG cell lines were cultured in different conditions in order to induce an undifferentiated phenotype. Then, ex vivo GBM cells from patients’ primary cell culture, were passed through the developed microfluidic system and characterized in order to reflect clinical conditions. This article demonstrates that the usual exploitation of low frequency range DEP does not allow the discrimination of the undifferentiated from the differentiated phenotypes of GBM cells. However, the presented study highlights the use of UHF-DEP as a relevant discriminant parameter. The proposed microfluidic lab-on-a-chip is able to follow the kinetic of U87-MG phenotype transformation in a CSC enrichment medium and their cancer stem cells phenotype acquirement.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

Older adults with obesity have an increased risk for cognitive decline and subsequent Alzheimer’s disease. Previous research has focused on the impact of individual nutrients and overall dietary patterns to improve cognitive function. The Brain and Body Health (BB-Health) study aims to demonstrate the feasibility of a multicomponent nutritional supplement (MCNS) and weight loss (WL) intervention for individuals with overweight and obesity who are not consuming a healthy diet. BB-Health is a parallel-group randomized placebo-controlled 2x2 factorial pilot trial comparing the MCNS, WL, and MCNS+WL with a Control group. Eligible participants are 55 to 85 years of age with a body mass index 27.0 to 39.9 kg/m2. Major exclusion criteria include type 2 diabetes, moderate or severe cognitive impairment, and self-reported healthy dietary pattern. The BB-Health feasibility trial is registered as NCT05542199 at clinicaltrials.gov. The BB-Health objectives are to report: 1) recruitment and enrollment, including pace and descriptive statistics of the study sample; 2) adherence to the administered interventions; 3) successful data collection and performance of outcome assessments, including evaluation of change in key outcomes over time that are powered for this pilot study; and 4) summary statistics on outcomes for use in planning a subsequent, larger trial. The outcomes of interest are age-sensitive cognitive assessments, cerebral hemodynamics, and related health parameters. All measurements are collected at baseline, 3-, 6-, and 12-month visits. If the BB-Health protocol demonstrates feasibility, the novel MCNS with and without a parallel WL intervention has potential to be administered in a confirmatory randomized trial to evaluate ability to prevent age-related cognitive decline and improve brain health. The BB-Health Feasibility Study could significantly contribute to our understanding of the influence of diet and weight management on cognitive health

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

Diffuse correlation spectroscopy (DCS) is a non-invasive technology for the evaluation of the blood perfusion in deep tissue. However, it requires high computational resources for data analysis which poses challenges in its implementation for real-time applications. To address the unmet need, we developed a novel device-on-chip solution that fully integrates all the necessary computational components needed for DCS. It takes the output of a photon detector and determines the blood flow index (BFI). It is implemented on a Field Programmable Gate Array (FPGA) chip including a multi-tau correlator for the calculation of the temporal light intensity autocorrelation function and a DCS analyzer to perform the curve fitting operation that derives the BFI. The FPGA DCS system was evaluated against a lab-standard DCS system for both phantom and cuff-ischemia studies. The results indicate that the autocorrelation of the light correlation and BFI from both the FPGA DCS and the reference DCS matched well. Furthermore, the FPGA DCS system was able to achieve a measurement rate of 50 Hz and resolve pulsatile blood flow.

This article introduces the design and analysis of a slope detection circuit tailored for on-chip sensing of the load current in DC-DC converters. The novel indirect sensing approach is grounded in measuring the output voltage slope across the filtering capacitor during discharge phases. Consequently, this slope data can be effectively harnessed to control the converter switches. The slope detector circuit was designed in standard 65 nm CMOS technology using the nominal supply voltage of 1.2 V and can be used for current sensing within the range from one to hundreds of mA. Since the proposed circuit has mainly digital character, the robustness to process, temperature and supply voltage variations can be ensured rather conveniently.