Water pollution is the main problem in the current scenario which is being faced by mankind due to the industrial and commercial effects. Industrial effluents contain heavy metals and inorganic ions like nitrates and phosphate ions. These ions are being included in waterways through industrial runoff. When the concentration of these hazardous pollutants increases in aquatic flora and fauna causes severe health problems. So remediation of these toxicants from water reserves is of chief importance. Conventional processes along with modern processes are being used for the treatment of industrial wastes. Photo-degradation is a modern method used for the degradation of inorganic ions due to its environmentally friendly nature and cost-effectiveness. In a recent study Aluminum oxide (Al2O3) nanoparticles were synthesized via a green approach at different pH by using Cymbopogan citratus (lemongrass) plant extract and these nanoparticles were used for the removal of inorganic ions from wastewater. The nanoparticles of different pH showed different % degradation of the inorganic ions in acidic medium removal of inorganic waste was less, in basic media % degradation was more as compared to acidic media but maximum % degradation was observed in neutral media like that average % degradation 91% and 81% was observed for nitrate and phosphate ions. The maximum absorbance occurred at 212nm and Al2O3 nanoparticles showed absorbance from 210nm-217nm. The R2 values of pseudo1st, 2nd, and BMG models were 0.956, 0.837, 0.7007 0.95, 0.896, and 0.756 for the nitrate and phosphate ions. Characterizations of synthesized particles were investigated by using UV-visible spectroscopy and other analytical methods like X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The statistical analyses were done using Simple Linear regression (SLR).

In this study we have investigated the effect of the addition of Nb2O5 (up to 5 mol%) on the structure and luminescent properties of ZnO-B2O3 glass doped with 0.5 mol % Eu2O3 by using of infrared (IR), Raman and photoluminescence (PL) spectroscopy. Physical properties as molar volume, oxygen packing density and glass transition temperature were determined using the results of differential thermal analyisis (DTA) and Archimedes principle for density. IR and Raman spectra revealed that niobium ions incorporate into the base zinc borate glass as NbO4 trtraherda and NbO6 octahedra. A strong red emission from the 5D0 level of Eu3+ ions was registered under near UV (392 nm) excitation using the sharp 7F0 - 5L6 transition of Eu3+. The integrated fluorescence intensity ratio R (5D0 → 7F2/5D0 → 7F1) was calculated to estimate the degree of asymmetry around the active ion, suggesting a location of Eu3+ in non-centrosymmetric sites. The higher Еu3+ luminescence emission observed in zinc borate glasses containing 1÷5 mol% Nb2O5 compared to the Nb2O5-free zinc borate glass evidences that Nb2O5 is suitable component for modification of host glass structure and improving the emission intensity.

Reactions of quinones with compounds containing an amino group can produce a wide variety of addition or substitution products that depend on reactivity of both quinone and amino derivative. 6,7-Dichloropyrido[1,2-a]benzimidazole-8,9-diones undergo selective nucleophilic substitution reaction with different benzohydrazides and α-hydroxy-p-quinone imine derivatives stabilized by strong intramolecular hydrogen bond were isolated. Synthesized compounds represent a combination of several structural motifs: benzimidazole core fused with α-hydroxy-p-quinone imine which contains a benzamido fragment. The protonation/deprotonation processes were investigated in a solution using UV-Vis spectroscopy and 1H NMR titration experiment. X-ray crystallography analysis revealed a set of weak non-covalent interactions such as intra- and intermolecular hydrogen bonds and π-π stacking. Additionally, the redox behavior of 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione and its p-imino derivative was investigated in acidic and neutral environment using cyclic voltammetry measurements. Cathode material based on 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione could act as potential effective active electrode in aqueous electrolyte batteries, however further optimization is required.

Arylmagnesium and -calcium reagents are easily accessible, however, ether degradation processes limit the storability especially of the calcium-based heavy Grignard reagents. Ortho-bound substituents with phosphanyl donor sites usually block available coordination sites and stabilize such complexes. The reaction of bromo-2,6-bis(diphenylphosphanylmethyl)benzene (1a) with magnesium in tetrahydrofuran yields [Mg{C₆H₃-2,6-(CH₂PPh₂)₂}₂] (2) after recrystallization from 1,2-dimethoxyethane. However, the similarly performed reduction of bromo- (1a) and iodo-2,6-bis(diphenylphosphanylmethyl)benzene (1b) with calcium leads to ether cleavage and subsequent degradation products. α-Deprotonation of THF yields 1,3-bis(diphenylphosphanylmethyl)benzene. Furthermore, the insoluble THF adducts of dimeric calcium diphenylphosphinate halides, [(thf)₃Ca(X)(µ-O₂PPh₂)]₂ [X = Br (3a), I (3b)], precipitate verifying ether decomposition and cleavage of P-C bonds. Ether adducts of calcium halides [such as [(dme)₂(thf)CaBr₂] (4)] form supporting the initial Grignard reaction and a subsequent Schlenk-type dismutation reaction.

A field experiment was conducted for 2 years in Green Tea Laboratory of Saitama Prefectural Agriculture and Forestry Research Center, Iruma, Saitama, Japan from March 2014 to December 2015. Controlled release fertilizers (CRF) or organic fertilizers (ORG) which is the mixture of chicken manure and oil cakewere applied with the amount of 450 kg N ha^-1 yr^-1 in 2014 and 397 kg N ha^-1 yr^-1 in 2015. Nitrous oxide (N₂O) emissionsfrom soil in green tea fields were measured by closed chamber method. The results showed that CRF has significantly lower N₂O compared to ORG. The cumulative N₂O emissions from CRF accounted for 51% of N₂O emissions from ORG fields and 138% of control with no fertilizer treatment. The N₂O flux from the row was higher than that of under the canopy, since fertilizer were applied on the row. However the total emission from the area between the rows was lower than that under the canopy because of the area ratio of row and canopy was 1:5.

Conventional fertilization practices can lead to many ecological problems, such as nutrient imbalance, soil acidity, and reduced soil fertility in natural rubber plantations. To address these challenges, a field investigation was strategically carried out to substitute inorganic fertilizer with organic fertilizers consisted of six treatments, i.e., no fertilization (CK), inorganic fertilizer (NPK), 25 % replacement of inorganic through organic (25%M), 50 % replacement of inorganic through organic (50%M), 75 % replacement of inorganic through organic (75%M), and 100% organic fertilizer (100%M). The soil physicochemical properties (SOC, TN, AN, C:N, pH, NH4+-N, and NO3--N) and carbon and nitrogen converting enzymes (BG, NAG, and LAP) were all determined. The partial substitution of inorganic fertilizers with organic fertilizers (i.e., 75%M at surface soil layer) showed higher SOC (14.52 g.kg-1), TN (1.06 g.kg-1), AN (20.07 mg.kg-1), C:N (14.63), NH4+-N (10.63 mgkg-1), and NO3--N(11.06 mg.kg-1) than NPK and CK. Such increase in physicochemical properties in partial replacement of inorganic with organic fertilizers plots resulted from higher carbon and nitrogen enzymes activities (BG (143.17 nmol.g-1.h-1), NAG (153.96 nmol.g-1.h-1), and LAP (153.48 nmol.g-1.h-1)) compared to NPK and CK, and further the person correlation and RDA analysis confirmed a significant positive correlation between SOC, AN, and soil enzymes. This study presents a new strategy for assessing the impact of partially replacing inorganic fertilizers with organic fertilizers in rubber plantations, mainly by modifying the soil nutrient composition in tropical regions.

Phase Change Materials (PCMs) are latent heat storage media with high potential of integration in building structures and technical systems. Their solid-liquid transition is commonly utilized for thermal energy storage in building applications. It also means that some kind of encapsulation is necessary. This is often solved with metal containers that also have high thermal conductivity and resistance to mechanical damage enhancing the performance these so called latent heat thermal energy storage (LHTES) systems. However selection of suitable metal is rather challenging. It depends, among other things, on the elimination of undesirable interaction between storage medium and surrounding metal. Heat storage medium must be reliably sealed in metal container especially when the storage system is integrated in systems like domestic hot water storage tanks, where PCM leaks can negatively affect human health. The aim of this study was evaluation of interaction between selected commercially available organic and inorganic PCMs and metals. The evaluation is based on the calculation of corrosion rate and use gravimetric method for determination of the weigh variations of the metal samples. Results show that aluminium is the most suitable container material with lowest mass loss and suffered only minimal visual changes on the surface after prolonged exposure to PCMs.

During the last years there has been a high interest in the development of new purely-organic single-component conductors. Very recently, we have reported a new neutral radical conductor based on the perchlorotriphenylmethyl (PTM) radical moiety linked to a monopyrrolo-tetrathiafulvalene (MPTTF) unit by a -conjugated bridge (1). Interestingly, this system behaves as a semiconductor with high conductivity and small energy gap under high pressure. With the aim of developing a new material with improved conducting properties, we have designed and synthesized the radical dyad 2 which was functionalized with an ethylenedithio (EDT) group in order to improve the intermolecular interactions of the TTF subunits. The physical properties of the new radical dyad 2 were studied in detail in solution to further analyze its electronic structure as well as its potential use as radical conductor in the solid state.

The chemical investigation of the anti-yeast methanol extract from the stem bark of Terminalia mantaly led to the isolation of seven compounds: 3-O-methyl-4-O-α-rhamnopyranoside ellagic acid (1), 3-O-mehylellagic acid (2), arjungenin or 2,3,19,23-tetrahydroxyolean-12-en-28-oïc acid (3), arjunglucoside or 2,3,19,23-tetrahydroxyolean-12-en-28-oïc acid glucopyranoside (4), 2α,3α,24-trihydroxyolean-11,13(18)-dien-28-oïc acid (5), stigmasterol (6), stigmasterol 3-O-β-D-glucopyranoside (7). Their structures were established by means of spectroscopic analysis and comparison with published data. Compounds 1-5 were tested in vitro for activity against three pathogenic yeast isolates, Candida albicans, Candida parapsilosis and Candida krusei. The activity of compounds 1, 2 and 4 were comparable to that of the reference compound fluconazole (MIC values below 32 µg/ml) against the three tested yeast isolates. They were also tested for inhibitory properties against four enzymes of metabolic significance: Glucose-6-Phosphate Deshydrogenase (G6PD), human erythrocyte Carbonic anhydrase I and II (hCA I and hCA II), Glutathione S-transferase (GST). Compound 4 showed highly potent inhibitory property against the four tested enzymes with overall IC₅₀ values below 4 µM and inhibitory constant (Ki) <3 µM.

Waste management is a significant issue that Indonesia must face. The presence of waste will always exist as long as life continues. One of the main challenges in waste management is the proper separation of organic and inorganic waste. As a solution to address this issue, the Ministry of Environment has made efforts to develop Waste Banks. However, it also creates new problems related to manual data collection, lack of monitoring by the community in implementing waste management activities, and a lack of specific reports regarding waste management conducted by officers. We propose the creation of a website using the Agile Development SDLC method. This website involve several steps and incorporate functions for data digitalization and expedited data collection, such as the addition of QR Code functionality, Monthly Reporting Function, and enhanced data security. The method used in this research is Agile Development. The application has been developed with a user-friendly interface and the latest web development technologies to ensure smooth performance. Overall, the web-based application for organic and inorganic waste using Laravel is an important step to promoting sustainable waste management practices.

Peptides, both natural and synthetic, are well suited for a wide range of purposes and offer versa-tile applications in different fields such as biocatalysts, injectable hydrogels, tumor treatment, and drug delivery. The rising prominence of therapeutic peptides encompasses anticancer, antiviral, antimicrobial, and anti-neurodegenerative properties. The metals Na, K, Mg, Ca, Fe, Mn, Co, Cu, Zn, and Mo are ten of the twenty elements that are considered essential for life. Crucial for under-standing the biological role of metals is the exploration of metal-bound proteins and peptides. Aside from essential metals, there are other, non-essential metals that also interact biologically, exhibiting either therapeutic or toxic effects. Irregularities in metal binding contribute to diseases like Alzheimer’s, neurodegenerative disorders, Wilson's, and Menkes disease. Certain metal com-plexes have potential applications as radiopharmaceuticals. The examination of these complexes was done by preforming UV-Vis, IR, EPR, NMR spectroscopy, and X-ray analysis.

Leishmaniasis are neglected diseases that affect regions such as South Asia, South Africa and Latin America, less developed regions. Current treatment, for cutaneous, mucocutaneous and visceral leishmaniosis, which are the main forms of the disease, is based on the administration of pentavalent antimonial and amphotericin B. However, these drugs have low efficacy and high toxicity. For this reason, the search for new treatments for this disease is necessary, based on studies of new molecules and their conformations. The research proposed the conformational study of brominated guanidine compounds with potential antileishmanial activity using Nuclear Magnetic Resonance (NMR) and X-ray diffraction (XRD) techniques. The present study involves the bro-minated molecules, LQOF-G2, LQOF-G30, LQOF-G35 and LQOF-G35-Br. The later was synthesized by the reaction of LQOF-G35 with NBS under IR irradiation at 120 Watts of potency and dichloro-methane as solvent by 12-h of exposition. The obtained results demonstrated the efficiency of the bromination method, since two bromines atoms entered the molecule. Furthermore, NMR analysis showed the occurrence of a conformational change from Z to E when compound LQOF-G35 was brominated to LQOF-G35-Br. This feature was well confirmed by comparative DRX study of the LQOF-G35 and LQOF-G35-Br compounds. The antileishmanial activity of LQOF-G2 e LQOF-G35 motivated the synthesis of new brominated compounds LQOF-G30 e LQOF-G35-Br.

: Nanotechnology has expanded what can be achieved in our approach to cancer treatment. The ability to produce and engineer functional nanoparticle formulations to elicit higher incidences of tumor cell radiolysis has resulted in substantial improvements in cancer cell eradication while also permitting multi-modal biomedical functionalities. These radiosensitive nanomaterials utilize material characteristics, such as radio- blocking/absorbing high-Z atomic number elements, to mediate localized effects from therapeutic irradiation. These materials thereby allow for subsequent scattered or emitted radiation to produce direct (e.g., damage to genetic materials) or indirect (e.g., protein oxidation, reactive oxygen species formation) damage to tumor cells. Using nanomaterials that activate under certain physiologic conditions such as the tumor micro-environment can selectively target tumor cells. These characteristics combined with biological interactions that can target the tumor environment allow for localized, radio-sensitization while mitigating damage to healthy cells. This review explores the various nanomaterial formulations utilized in cancer radiosensitivity research. Emphasis on inorganic nanomaterials showcase the specific material characteristics that enable higher incidences of radiation while ensuring localized cancer targeting based on tumor micro-environment activation. The aim of this review is to guide future research in cancer radiosensitization using nanomaterial formulations and to detail common approaches to radiosensization, as well their relations to commonly implemented radiotherapy techniques.

Healthcare professionals constantly face situations that reflect ecosystems’ degradation. These can negatively affect their mental health. Research suggests that hope and resilience can play an important role in this scenario, since they are related to/predict mental health in highly heterogeneous samples (considering geography, age, profession, health, etc.). In this context, the aims of the present study are: to characterize and explore the relationship between hope, resilient coping and mental health of Portuguese healthcare professionals. Using Google Forms, 276 healthcare professionals answered to the GHQ-28, the (adult) Trait Hope Scale, and the Brief Resilient Coping Scale (cross-sectional study). The minimum and maximum possible scores were reached, with the exception of the maximum score of GHQ-28-Total. Regarding Hope, 19.6% scored below the midpoint (M=43.46, SD=11.97); 29.3% revealed low resilience (M=14.93, SD=4.05); and the average of 4 of the 5 Mental Health scores (exception: Severe Depression) indicates the probability of a psychiatric case. Hope correlated with Social Dysfunction and GHQ-28-Total; resilient coping proved to be a (weak) predictor of 4 of the 5 GHQ-28 indicators (exception: Severe depression). The results support the need to promote the sample's mental health, hope and resilient coping. They also suggest that stimulating resilient coping may contribute to improving healthcare professionals’ mental health.

A Cu₂ZnSnS₄ (CZTS) film with a thickness of approximately 1.5 μm was fabricated on a Mo-coated glass substrate by annealing a CZTS precursor fabricated from nanoparticle ink. The chemical states of the elements in the CZTS thin film in the depth direction were studied to identify the presence of secondary phases, which are detrimental to the performance of solar cells containing CZTS. X-ray diffraction was unable to detect any secondary phases in CZTS because of their small relative amount. Instead, X-ray photoelectron spectroscopy (XPS), which is highly sensitive to chemical state, was conducted at different depths in the CZTS film to further check the presence of secondary phases. XPS analysis revealed peaks shift consistent with the presence of secondary phases. For the CZTS film annealed in a S atmosphere at 575 °C for 3 h, the film surface consisted of a secondary-phase layer composed of CuS, ZnS, and SnSx (x=1 or 2) originating from the decomposition of CZTS. At depths below 80 nm, the film was pure CZTS. Formation of MoS2 at the CZTS–Mo interface was confirmed by XPS analysis of Mo and S.

This study addresses the urgent need for sustainable protein sources in aquaculture due to the depletion of marine resources and rising costs. Animal protein sources, particularly poultry by-product meal (PBM) and insect exuviae meal, are investigated as viable alternatives to fishmeal (FM). Research confirms the successful replacement of FM with a combination of PBM and insect exuviae meal (up to 50%) in the diet of European seabass without compromising growth, feed conversion, gut health and liver fat content. In particular, growth performance was robust with both PBM formulations, with the 25% PBM diet showing better results. Histological examinations showed good gut and liver health, contradicting the concerns of previous studies. The study emphasizes the importance of holistic analyzes that go beyond growth parameters and include histomorphological investigations. The results show that PBM in combination with insect/exuviae meal is well tolerated by seabass, which is consistent with literature reports of mitigating negative effects on gut health. A detailed analysis of the microbiota revealed a decrease in the Firmicutes/Proteobacteria ratio due to an increase in potentially pathogenic bacteria. However, the formulation containing insect exuviae partially counteracted this effect by preserving the beneficial Lactobacillus and promoting the synthesis of short-chain fatty acids (SCFA), particularly butyrate. Chitin-rich components from insect exuviae were associated with improved gut health, which was supported by increased production of SCFA, which are known for their anti-inflammatory properties. The study concludes that a combination of PBM and insect/exuviae meal can replace up to 50% of FM in the diet of seabass, supporting sustainable aquaculture practices. Despite some changes in the microbiota, the negative effects are mitigated by the addition of insect exuviae, highlighting their potential as a prebiotic to increase fish productivity and contribute to a circular economy in aquaculture.

Soot combustion experiments with 5%O2/He were conducted using model soot, and four distinct compositions of CexPr1-xO2-δ oxides were prepared, varying nominal cerium com-positions (x=0, 0.2, 0.3, and 1). The catalyst samples were comprehensively characterized using techniques such as XRD, Raman spectroscopy, HR-TEM, N2 adsorption at −196 °C, XPS, O2-TPD, H2-TPR, and work function measurements. The Pr-rich compositions, rang-ing from Ce0.3Pr0.7O2-δ to PrO2-δ, resulted in a significant increase in the total evolved O2 amounts and enhanced catalyst reducibility. However, a decrease in textural properties of the catalysts was noted, being particularly important for the pure praseodymia under the synthesis route conducted. The catalytic activity was investigated under two contact modes of mixing between soot and catalyst: loose and tight. The results revealed that the catalytic performance is associated with the surface contact in tight contact mode and with the combination of surface/subsurface/bulk oxygen mobility and the BET surface ar-ea in loose contact mode. Notably, the T10 and T50 parameters were achieved at much lower temperatures than the uncatalyzed soot combustion, even under loose contact conditions. Specifically, the 50% conversion was achieved at 511℃ and 538℃ for Ce0.3Pr0.7O2 and Ce0.2Pr0.8O2, respectively. While no direct correlation between catalytic activity and work function was observed a significant relationship emerges between work function values and the formation of oxy-gen vacancies, whatever the conditions used for these measurements. On the other hand, the ability to generate a high population of oxygen vacancies at low temperatures, rather than the direct activation of gas-phase O2, influences the catalytic performance of Pr-doped ceria catalysts, highlighting the importance of surface/subsurface oxygen vacancy generation, which was the parameter which showed better correlation with the catalytic activity, whatever the soot conversion value or the mode of contact considered.

To stabilize the Earth’s climate a large-scale transition is needed to non-carbon emitting renewable energy technologies like wind and solar energy. Although these renewable energy sources are now lower-cost than fossil fuels, their inherent intermittency make them unable to supply a constant load without storage. To address these challenges rechargeable electric batteries are currently the most promising option; however, their high capital costs limit current deployment velocities. To both reduce the cost as well as improve performance 3D printing technology has emerged as a promising solution. This literature review provides the state-of-the-art enhancements of battery properties with 3D printing including efficiency, mechanical stability, energy and power density, customizability and sizing, production process efficiency, material conservation and environmental sustainability as well as the progress in solid-state batteries. The principles, advantages, limitations, and recent advancements associated with the most common types of 3D printing are reviewed focusing on their contributions to the battery field. 3D printing batteries offer design flexibility, material flexibility, reduces pack weight, minimizes material waste, increases the range of applications and has the potential to reduce costs. As 3D printing technologies become more accessible, the prospect of cost-effective production for customized batteries is extremely promising.

Theoretical studies on the generation of nondiffracting and nondispersive light pulses and their experimental implementation are one of the renowned problems within electromagnetics. Current technologies enable creation of short-duration pulses of a few cycles with high power and fluency. An application of these techniques to the field of nondiffracting and nondispersive pulses requires a proper mathematical description of highly focused vector pulses. In this work, we study vector optical bullets in a dielectric medium with different polarization structures: linear, azimuthal, and radial. We report the differences caused by the vector model compared to the scalar model. We analyze effects caused by superluminal, subluminal, or even negative group velocity on properties of vector optical bullets inside a dielectric material.

Global warming and the global energy crisis are two major challenges humanity is currently confronting that are pressuring the scientific community to find efficient, low cost and environmentally sustainable solutions. Within this context, hydrogen has emerged as a clean and efficient energy carrier promising to replace the environmentally hazardous fossil fuels. The present study, of relevance to the water splitting domain, concerns the synthesis of two novel hybrid structures, based on perovskite materials functionalized with polyvinylpyrrolidone (PVP). The water electrolysis catalytic activity of these new materials was evaluated in a strongly alkaline medium. Perovskite-based modified electrodes were manufactured through four different procedures. The samples displayed electrocatalytic activity for the O2 evolution reaction and the most active electrode was the one obtained by drop-casting a mixture of LaMnO3:Ag/PVP, Carbon Black and Nafion on graphite support. The study is aimed at and succeeds in increasing the scientific database concerning the role of perovskite oxides in the water splitting field.

SOC stock (SOCS) changes caused by land use changes are still unclear, and understanding this response is essential for many environmental policies and land management practices. In this study, we investigated the temporal-spatial and vertical distribution characteristics of SOCS on the Western Sichuan Plateau (WSP) using the sparrow search algorithm-random forest regression (SSA-RFR) models with excellent model applicability and accuracy. The temporal-spatial varia-tions in the SOCS were modeled using 1080 soil samples and a set of nine environmental covariates. We analyzed the effect of land use changes on the SOCS on the WSP. The total SOCS increased by 18.03 Tg C from 1990 to 2020. The results of this study confirmed that the SOCS in the study area has increased significantly since 2010, with an increase of 27.88 Tg C compared to the total SOCS in 2010. We found that the spatial distribution of the SOCS increased from southeast to northwest, and the vertical distribution of the SOCS in the study area decreased with increasing soil depth. Forest and grassland are the main sources of SOCS, the total SOCS in the forest and grassland accounted for 37.53 and 59.39% of the total SOC pool in 2020, respectively. Expansion of the wetlands, forest, and grassland areas could increase SOCS in the study area.

The aim of the study was to determine the maximum safe concentration of calcium and phosphate in neonatal parenteral nutrition (PN) solutions when various combinations of inorganic and organic salts are applied. Twelve PN solutions for neonatal use were aseptically prepared. Increasing concentration of inorganic and organic calcium and phosphate were added to the standard formulas. Each admixture was separately tested according to following conditions; after mixing, 37°C for 24 h, and maximum safe combination of calcium and phosphate were stored at 4°C for 30 days and followed by 24 h at 37°C. Visual inspections against a black and white contrast background, microscopic observation of undiluted PN solutions as well as the membrane filter after filtration of the PN solution, pH evaluation, and spectrophotometry at 600 nm were examined in triplicate. Safe maximum concentration of organic and inorganic calcium and phosphate was proposed individually for each composition of parenteral nutrition solutions. Surprisingly organic calcium with organic phosphate showed precipitation but over the therapeutic range. The protective effect of amino acid was observed and higher concentrations of calcium and phosphate were free of precipitation.

The presence of antibiotic residues in honey has recently become a growing public health concern due to the overuse of these products in beekeeping and their transfer to the food industry. The aim of this study was to develop and validate a simple, selective and sensitive method for the simultaneous identification and quantification of residues of twenty-two sulfonamides, trimethoprim and dapsone in honey using a rapid and reliable liquid chromatography–tandem mass spectrometry (LC–MS/MS) method. The developed method showed good linearity, specificity, precision (repeatability and intra-laboratory reproducibility) and recovery. The decision limit (CCalpha) ranged between 2.16-22.12 µg/kg for CCα, while the detection capability (CCbeta) was between 2.16- 2.67-27.36 µg/kg. The method proved to be rapid, reliable and effective for the determination of sulfonamides, trimethoprim and dapsone from honey samples. The average recoveries were estimated to be between 70 and 106%. The relative standard deviations (RSDs) were between 6-18%. In practice, the method is essential to check the honey sold on the market and ensure its safety before it reaches the consumer.

Periodontitis is a chronic inflammatory disease which results in the destruction of the tooth’ s supporting tissues and the alveolar bone resorption. The complement becomes a major link between infection and inflammatory pathology including periodontitis. Gingipians as important virulence factors of P. gingivalis have the activity of C5 convertase, could cleave C5 into fully functional C5a to activate C5aR. The above process could be blocked by the C5aR antagonist (PMX-53) to suppress local periodontal inflammation, and then achieves the purpose of treatment of periodontitis. Nanoparticles incorporated within gelatin are promising carrier system for drug delivery in recent years. This study aimed to investigate whether gelatin nanoparticles loaded with PMX-53 prevents alveolar bone resorption in miniature swines model of periodontitis. Four miniature swines were placed ligatures around the maxillary and mandibular fourth premolar and first molar on both sides for seven weeks to induce periodontitis. Then, animals were assigned randomly to four groups: minocycline-treated group, gelatin with PMX53-treated group, gelatin-treated group and a sham control group. They were treated with 1ml related drugs respectively, into gingival sulcusl for 4 times at one-week intervals. We showed that local treatments with gelatin nanoparticles loaded with PMX-53 could inhibit alveolar bone loss of periodontitis. Our study revealed that gelatin nanoparticles loaded with PMX-53 prevented alveolar bone resorption miniature swines model of periodontitis. In addition, provided proof-of-concept for local targeting of gelatin nanoparticles loaded with PMX-53 as a powerful candidate for the treatment of periodontitis.

The treatment of the bulky Rind-based dibromosilanes, (Rind)2SiBr2 (2) [Rind = 1,1,7,7-tetra-R1-3,3,5,5-tetra-R2-s-hydrindacen-4-yl: EMind (a: R1 = Et, R2 = Me) and Eind (b: R1 = R2 = Et)], with two equivalents of tBuLi in Et2O at low temperatures resulted in the formation of blue solutions derived from the diarylsilylenes, (Rind)2Si: (3). Upon warming the solutions above −20 °C, the blue color gradually faded, accompanying the decomposition of 3 and yielding the cyclic hydrosilanes (4) via intramolecular C−H bond insertion at the Si(II) center. The molecular structures of the bulky Eind-based 3b and 4b were confirmed by X-ray crystallography. Thus, at −20 °C, blue crystals were formed (Crystal-A), which were identified as mixed crystals of 3b and 4b. Additionally, colorless crystals of 4b as a singular component were isolated (Crystal-B), whose structure was also determined by an X-ray diffraction analysis. Although the isolation of 3 was difficult due to their thermally-labile nature, their structural characteristics and electronic properties were discussed based on the experimental findings complemented by computational results. We also examined the hydrolysis of 3b to afford the silanol, (Eind)2SiH(OH) (5b).

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

The species and bio-availability of phosphorus (P) in primary, secondary and digested sludge were fractionated and further analyzed in this study. Results showed that inorganic P (IP) was the primary P fraction in the secondary sludge and digested sludge, in which non-apatite IP (NAIP) amounted to 91.6% and 69.3% of IP, respectively. Organic P (OP), accounting for about 71.7% of total P (TP), was the dominant P composition in primary sludge. The content of bio-available P was about 9.7, 43.4, 29.8 mg-P/g-TS in primary sludge, secondary sludge and digested sludge, respectively, suggesting secondary sludge is the optimal choice when land application of sewage sludge is taken into consideration, followed by digested sludge and primary sludge. Polyphosphate and orthophosphate, comprising approximately 54.3% and 89.2% of TP, was the dominant P species in the secondary sludge and digested sludge, respectively. Monoester-P (54.6% of TP in extract) and diester- P (24.1%) were identified as OP species in primary sludge by Phosphorus-31 nuclear magnetic resonance (31PNMR). The present results would be helpful for P recovery and recycle from sewage sludge in wastewater treatment plant.

Iapetus, a Saturn moon, shows the most differentiated albedo dichotomy of the Solar System. The dark leading side has a lower albedo than the bright trailing side. Spectral data on the visible light reveal the existence of two types of materials on the surface. The darkening in the leading side is thought to be originated by the presence of organic material and carbonaceous compounds on surface, while the trailing side is covered by water ice due to migration processes from the dark side. On airless bodies like Iapetus, the surface escape speed is greater than the speed of water molecules, resulting in the retention of a H2O atmosphere that allows some species to get diffused through it. Here, there were performed simulations of the evolution of the surface temperature for each of the two hemispheres of Iapetus. The results showed a slow yet steady increment of temperatures for both sides, with a steeper slope for the dark hemisphere. It was also simulated how much energy budget can be accumulated in both sides and its consequences. Finally, we calculated the diffusion coefficients for ammonia, methane, and water ice. The results let us infer how these compounds could evolve over time.

Non-coding RNAs have been described as crucial regulators of gene expression and guards for cellular homeostasis. Some recent papers are focused on vault RNAs, one of the classes of non-coding RNA, and their role in cell proliferation, tumorigenesis, apoptosis, cancer response to therapy, and autophagy, which made them potential therapy targets in oncology. In the human genome, four vault RNA paralogues can be distinguished. They are associated with vault complexes, considered the largest ribonucleoprotein complex. The protein part of these complexes consists of a major vault protein (MVP) and two minor vault proteins (vPARP and TEP1). The name of the complex, as well as vault RNA, comes from the hollow barrel-shaped structure that reminds a vault. Their sequence and structure are highly evolutionary conserved and show many similarities in comparison with different species, but vault RNAs show various roles. Vaults were discovered in 1986, and their functions remained unclear for many years. Although not much is known about their contribution to cell metabolism, it has become clear that vault RNAs are involved in various processes and pathways associated with cancer progression and modulating cell functioning in normal and pathological stages. In this review, we discuss known functions of the human vault RNAs in the context of cellular metabolism, emphasizing processes related to cancer and cancer therapy efficacy.

Esterquats constitute a unique group of quaternary ammonium salts (QASs) that contain an ester bond in the structure of the cation. Despite the numerous advantages of this class of compounds, only two mini-reviews discuss the subject of esterquats: the first one (2007) briefly summarizes their types, synthesis, and structural elements required for a beneficial environmental profile and only briefly covers their applications whereas the second one only reviews the stability of selected betaine-type esterquats in aqueous solutions. The rationale for writing this review is to critically reevaluate the relevant literature and provide others with a “state-of-the-art” snapshot of choline-type esterquats and betaine-type esterquats. Hence, the first part of this survey thoroughly summarizes the most important scientific reports demonstrating effective synthesis routes leading to the formation of both types of esterquats. In the second section, the susceptibility of esterquats to hydrolysis is explained, and the influence of various factors, such as the pH, the degree of salinity or the temperature of the solution, was subjected to thorough analysis that includes quantitative components. The next two sections refer to various aspects associated with the ecotoxicity of esterquats. Consequently, their biodegradation and toxic effects on microorganisms are extensively analyzed as crucial factors that can affect their commercialization. Then, the reported applications of esterquats are briefly discussed, including functionalization of macromolecules, such as cotton fabric as well as their successful utilization on a commercial scale. The last section demonstrates the most essential conclusions and reported drawbacks that allow us to elucidate future recommendations regarding the development of these promising chemicals.

Green synthesis of silver nanoparticles (AgNPs) using raw Whey has never been reported. Silver nanoparticle formation involves a reduction reaction of silver salt solution with Whey extract. Extract and metal salt concentrations, and temperature can control this reaction. In this work, incubation period, extract, AgNO3, and NaOH concentrations were used as the independent factors using central composite design under response surface methodology. The aim was to elucidate the influence these factors have on the measured UV-Vis absorption spectra fitted with a Voigt function, and to optimize the conditions for nanoparticle formation. The fitting parameters, peak wavelength (λ0), peak area (A), and Full Width at Half Maximum (FWHM), were the responses. Silver nanoparticle formation was only possible in an alkaline environment (pH 10). The peak wavelength and the FWHM are influenced mainly by extract and AgNO3 concentrations. In contrast, the peak area is influenced by a total of 33.54 % from the interaction terms of AgNO3 and extract concentrations with NaOH. Metallic AgNPs were formed for the following parameter ranges: a) Whey (0.4 – 1.6 % v/v), b) AgNO3 (0.15 – 0.6 mM), c) NaOH (10 – 50 mM), and d) Time (20 – 60 min). Silver oxide nanoparticles were also observed.

To secure logic circuits against the illegal copying the insertion of the so-called key bit inputs using XOR/XNOR gates has been proposed in . The inserted gates modify (lock) the behavior of the original circuit and only the correct choice of the secret key bits guarantees the equivalent behaviour of the locked circuit to the original circuit. To break this kind of security, i.e. to find the secret key bits, there was a SAT solver based attack proposed in . The aim of this work is to experimentally verify this attack on several locked circuits with various number of primary inputs and outputs and with various number of gates. Except for the random placement of the key gates we evaluate also the positioning with chaining elimination. The obtained and presented results show that we were able to unlock 10 of 11 circuits within few minutes on a common PC.

Coronavirus disease 2019 (COVID-19) has affected medical practice. More than 7,000,000 patients died worldwide after being infected with COVID-19; however, no specific laboratory markers have yet been established to predict death related to this disease. In contrast, electrocardiographic changes owing to COVID-19 include QT prolongation and ST-T changes; however, there have been no studies on ambulatory electrocardiographic markers of COVID-19. We encountered three patients diagnosed as having COVID-19 who did not have a prior history of significant structural heart diseases. All had abnormalities in ambulatory echocardiogram parameters detected by high-resolution 24-h electrocardiogram monitoring: positive late potentials (LPs) and T-wave alternans (TWA), abnormal heart rate variability (HRV), and heart rate turbulence (HRT). Case 1 involved a 78-year-old woman with a history of chronic kidney disease, Case 2 a 76-year-old man with hypertension and diabetes, and Case 3 a 67-year-old man with renal cancer, lung cancer, and diabetes. None of them had a prior history of significant structural heart disease. Although no significant consistent increases in clinical markers were observed, all three patients died, mainly because of respiratory failure with mild heart failure. LP, TWA, HRV, and HRT were all positive in three cases with no significant structural cardiac disease at the initial phase of admission. There is a possibility that LP, TWA, HRV, and HRT have the potential to be risk stratifiers of COVID-19 pneumonia in the early phase of admission. Further accumulation of data regarding ambulatory electrocardiographic markers in patients with COVID-19 is needed.

The paper discusses the mechanism of montmorillonite structure alteration and bentonites properties modification (on the example of samples from clay deposit Taganka, Kazakhstan) due to the thermochemical treatment (treatment with inorganic acid solutions at different temperatures, concentrations and reaction times). With the use of the suit of methods certain processes were distinguished: transformation of montmorillonite structure, which appears in the leaching of interlayer and octahedral cations, protonation of the interlayer and OH groups at octahedral sheets. Changes in the structure of the 2:1 layer of montmorillonite and its interlayer result in significant changes in the properties – reduction of cation exchange capacity and an increase of specific surface area. The results of the work showed that bentonite clays retain a significant portion of its adsorption properties even after the long term and intense thermochemical treatment (6M HNO3, 60°C, 108 hours)

Spinocerebellar ataxia type 3 is a neurodegenerative disease caused by an abnormal expansion of CAG repeats in the disease gene ATXN3, leading to prolonged polyglutamine (polyQ) tracts in the respective protein ataxin-3. The polyQ-expanded protein forms polyQ-containing aggregates in several brain regions which leads to neuronal cell loss. Autophagy is thought to play a significant role in clearing these polyQ-containing protein aggregates. Therefore, the autophagy mechanism was investigated in SCA3 with focus on the autophagic protein p62/sequestosome-1. Human and mouse RNA sequencing data were analyzed to determine RNA expression level of autophagic genes. Additionally, autophagy was studied in the SCA3 304Q knock-in mouse model and through several cell culture experiments using HEK-293T cells transfected with ATXN3 of differ-ent polyQ lengths. For cell culture experiments, autophagy was induced with rapamycin treat-ment, proteasomal degradation was blocked with MG132 and degradation of autophagic pro-teins was investigated using cycloheximide treatment. Here, we report an increased autophagy impairment with SCA3 disease progression seen in HEK-293T cells transfected with ATXN3 plasmid with expanded polyQ tracts, higher aged 304Q-knock-in mice, or human post-mortem brain material. Furthermore, co-localized aggregation of the autophagic protein p62 and the dis-ease protein ATXN3 was observed in the course of SCA3 disease. Therefore, we suggest a signifi-cant role for p62 in aggregate formation seen in the neurodegenerative disease SCA3.

Antioxidant, anti-inflammatory and chemo-preventive features have been reported for the carotenoid diatoxanthin. Diatoxanthin is only produced by a few groups of microalgae where it functions in photoprotection. Its large-scale production in microalgae is currently not feasible. In fact, rapid conversion into the inactive pigment diadinoxanthin is triggered when the cells are removed from the high-intensity light source, which will be the case during large-scale harvesting of microalgae biomass. Zeaxanthin epoxidase (ZEP) 2 and/or ZEP3 have been suggested to be responsible for the back-conversion of high-light accumulated diatoxanthin to diadinoxanthin in low light in diatoms. Using the CRISPR/Cas9 gene editing technology we knocked out the ZEP2 and ZEP3 genes in the already commercially used marine diatom Phaeodactylum tricornutum to investigate their role in the diadinoxanthin-diatoxanthin cycle, and to determine if one of the mutant strains could function as a diatoxanthin production line. Light shift experiments proved that ZEP3 encodes the enzyme converting diatoxanthin to diadinoxanthin in low light. Loss of ZEP3 caused the high-light accumulated diatoxanthin to be stable for several hours after the cultures had been returned to low light, suggesting that zep3 mutant strains could be suitable as commercial production lines of diatoxanthin.

The recent increase in global consumption of rice has led to increased demand for sustainable water management in paddy cultivation. In this study, we propose an enhanced paddy simulation module to be introduced to Soil and Water Assessment Tool (SWAT) to evaluate the sustainability of paddy cultivation. The enhancements added to SWAT include: (1) modification of water balance calculation for impounded fields, (2) addition of an irrigation management option for paddy fields that are characterized by flood irrigation with target water depth, and (3) addition of a puddling operation that influences the water quality and infiltration rate of the top soil layer. In a case study, the enhanced model, entitled SWAT-Paddy, was applied to an agricultural watershed in Japan. The results showed that the SWAT-Paddy successfully represented paddy cultivation, water management, and discharge processes. Simulated daily discharge rates with SWAT-Paddy (R² = 0.8) were superior to the SWAT result (R² = 0.002). SWAT-Paddy allows the simulation of paddy management processes realistically, and thus can enhance model accuracy in paddy-dominant agricultural watersheds.

Background: Respiratory syncytial virus[ RSV] is a lethal overwhelming defectiveness that influences people all over the world. The infection gets down in the lower respiratory tract and does not disperse to the remainder of the body. The objective of the study: Bioinformatics was used to create an mRNA vaccine against the Respiratory syncytial virus( RSV). Methodology: Lipid nanoparticle vaccines containing the Respiratory syncytial virus's surface fusion protein's mRNA were created for the current screening experimental investigation. Lipid nanoparticles[ LNP] with a particle size of around 90 nanometres that were created using the hot micro-emulsion process comprise the current vaccine delivery system. In stages 1 and 2 of clinical trials, the immunogenicity of the current mRNA RSV vaccine was evaluated. Results: The current vaccine demonstrated 81% immunogenicity in animal testing, but only 69% in stages 1 and 2 of clinical trials. Its side effects were manageable. The results persisted for a while. In the current trial, the vaccination proved effective as a preventative measure against RSV infection. The current immunization lacks antibody-dependent enhancement, which causes non-protective antibodies to develop. These non-neutralizing antibodies worsen infection by enhancing viral entrance and replication in the host cells, activating cytokines and the complement cascade through the production of immunological complexes, or both. However, the current LPN-RSV mRNA vaccine of the surface fusion protein resulted in the formation of potent neutralizing antibodies with persistent protection, especially for newborns and elderly individuals who get the ideal dose regimen. Conclusion: The invention of the LNP-mRNA RSV vaccine, which might prevent RSV-caused bronchiolitis and fatal pneumonia, made the current study promising

The present work reports the effective method for removal of inorganic and organic pollutants using membranes based on different carbonaceous materials. The membranes were prepared based on cellulose acetate (18 wt. %), polyvinylpyrrolidone as a pore generating agent (2 wt. %) and activated carbon (1 wt.%). Activated carbons were developed from residues after extraction of mushroom Inonotus obliguus using microwave radiation. It has been shown that addition of activated carbon the physical (porosity, equilibrium water content and permeability) and chemical (content of the surface oxygen group) properties of the membranes. The addition of carbon material has a positive effect on the removal of copper ions from their aqueous solutions by the cellulose-carbon composites obtained. Moreover, the membranes were proved to be more effective in removal of copper ions than iron ones and phenol. The membranes were found to show higher effectiveness in copper removal from a solution of the initial concentration 800 mg/L. The most efficient in copper ions removal was the membrane containing urea-enriched activated carbon.

We report neutralization titer data against contemporary SARS-CoV-2 sublineages from an ongoing, open-label, phase 2/3 trial of a single 30-μg dose of monovalent Omicron XBB.1.5-adapted BNT162b2 vaccine. Healthy participants had previously received ≥3 doses of a US-authorized mRNA vaccine, with the most recent being a bivalent Omicron BA.4/BA.5-adapted vaccine administered ≥150 days before study vaccination. In this analysis, Omicron XBB.1.5, BA.2.86, and JN.1 serum neutralizing titers were assessed at baseline and 1 month after vaccination in a subset of ≥18-year-olds (N = 40) with evidence of previous SARS-CoV-2 infection. Immunogenicity was also evaluated in a demographically matched group of participants who received bivalent BA.4/BA.5-adapted BNT162b2 in another study (ClinicalTrials.gov Identifier: NCT05472038). The XBB.1.5-adapted BNT162b2 vaccine elicited higher XBB.1.5, BA.2.86, and JN.1 neutralizing titers than those elicited by bivalent BA.4/BA.5-adapted BNT162b2. Overall geometric mean fold rises in neutralizing titers from baseline to 1 month after vaccination were higher among participants who received XBB.1.5-adapted BNT162b2 than those who received bivalent BA.4/BA.5-adapted BNT162b2 for XBB.1.5 (7.6 vs 5.6), slightly higher for JN.1 (3.9 vs 3.5), and similar for BA.2.86 (4.8 vs 4.9). ClinicalTrials.gov Identifier: NCT05997290.

(1) Background: In this work, a series of benzimidazole derivatives containing colchicine-like and cathechol-like moieties with methyl group substitution in the benzimidazole ring were evaluated for their in vitro antiproliferative, pro-apoptotic and antioxidative activity against highly invasive breast cancer cell line MDA-MB-231 and related impairment of tubulin dynamics; (2) Methods: MTT assay was used to evaluate the antiproliferative activity. In vitro tubulin polymerization assay as well as docking analysis was applied to prove the alterations in tubulin polymerization. Immunofluorescent and DAPI staining reveal the pro-apoptotic potential of benzimidazole derivatives and the effect on tubulin’s dynamics in living cells. The antioxidant activity was evaluated by scavenging of H2O2 and hypochlorite ion and ortho-phenanthroline tests; (3) Results: The compounds containing colchicine-like moiety displayed significant growth inhibitory effect against cancer cell line as was highlighted the role of methyl functional group on the tubulin aggregation and blockage of mitosis. All compounds showed an ability to scavenge H2O2, while the compounds with cathecol-like moiety were more effective against hypochlorite ion and chelation of iron; (4) Conclusions: The benzimidazole derivative containing colchicine-like moiety and methyl group substitution in benzimidazole ring is a potential antiproliferative and microtubule destabilizing agent.

The present study was performed to examine that transforming growth factor beta (TGF-β) in root-surrounding tissues on deciduous teeth during the physiological root resorption regulates the differentiation induction into odontoclast. We prepared root-surrounding tissues with (R) or without (N) physiological root resorption scraped off at three regions (R1-R3 or N1-N3) from the cervical area to the apical area of the tooth and measured both TGF-β and the tartrate-resistant acid phosphatase (TRAP) activities. The TGF-β activity level was increased in N1-N3, whereas the TRAP activity was increased in R2 and R3. In vitro experiments for RANKL-mediated osteoclast differentiation revealed that TGF-β in N1-N3 and R1-R3 enhanced the TRAP activity in RAW264 cells. A genetic study indicated that the mRNA level of TGF-β1 in N1 and N2 was significantly increased, and corresponded with that of osteoprotegerin (OPG). In contrast, the expression level of receptor activator of NF-κB ligand (RANKL) was increased in R2 and R3. Our findings suggest that TGF-β is closely related to the regulation of OPG induction and RANKL-mediated odontoclast differentiation depending on the timing of RANKL and OPG mRNA expression in the root-surrounding tissues of deciduous teeth during physiological root resorption.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Chitosan (CS) nanoparticles are under investigation for a wide range of applications in nanomedicine. The structural, molecular and physicochemical properties of chitosan nanoparticles have a direct bearing on their efficacy in drug conjugation and delivery, gene delivery, and tissue engineering. Herein we report on the structural, morphological and molecular properties of chitosan nanoparticles synthesized using the ionic gelation method with the intended purpose of being used for drug delivery. The chitosan nanoparticles (CS-NPs) were prepared in the 0.25 to 1.0% w/v concentration range, whereas separate samples of the 1.0% w/v CS-NPs were also functionalized with polyethylene oxide (PEO) alone and with a diblock copolymer of PEO and polypropylene glycol (PPG). The average size of the CS-NPs was determined from TEM imaging to be in the range of 11.3 to 14.8 nm. The XRD and TEM analyses show that the CS-NPs have semi-crystalline structure with the degree of crystallinity depending upon the nature of synthesis. Our results show that functionalizing the 1.0% w/v CS-NPs with PEO increases the degree of crystallinity whereas functionalizing with the diblock copolymer PEO - PPG results in a significant increase in their degree crystallinity. The CS/TPP concentration (CS:TPP fixed at 1:1 ratio) had no apparent effect on the degree of crystallinity of the CS-NPs. The results from the FTIR analysis confirm incorporation of TPP with CS in the CS-NPs. Additionally, FTIR analysis shows an enhancement of hydrogen bonding that is consistent with the increase in the degree of crystallinity of the CS-NPs.

Promoting organic foods production and consumption contributes to accomplishing United Nations sustainable development goals. Social commerce provides a promising opportunity to develop the organic food industry. However, there is limited knowledge regarding customer behaviors in relation to purchasing organic foods via social commerce platforms. Therefore, this study expanded upon the unified theory of acceptance and use of technology (UTAUT-2) to develop a comprehensive model that explains how customers' social commerce trust and behavioral intentions to purchase organic foods using Instagram social commerce affect their purchasing behaviors. The research model was analyzed by employing partial least squares structural equation modeling (PLS-SEM) for the data collected from a quantitative survey of 410 customers who used Instagram to purchase organic foods in Iran. The results revealed that facilitated purchasing conditions, hedonic motivations, social influence, rating and reviews, and influencers’ endorsements increase customers' purchase intentions. Moreover, Instagram’s recommendations and referrals, influencers’ endorsements, as well as social influence boost customers' trust in the social commerce platform. Eventually, it was determined that influencers’ endorsements, social commerce trust, and purchase intention determine a customer’s organic foods purchasing behaviors. This research provides valuable insights for organic food marketers to optimize their social commerce strategies.

The 5-hydroxymethylfurfural (HMF) is a six-carbon heterocyclic organic compound with two substituents an aldehyde group and an alcohol group. It is formed from saccharides as a result of two reactions: the Maillard reaction and the caramelization of saccharides. It has both a negative and a positive effect on the human body, which makes it, even more, an attractive research object. The objective of the study was to determine HMF content in honey samples available on the Polish market using three varied methods and compare the results obtained. The methodology used included: two spectrophotometric methods (by White and Winkler) and the HMF determination method based on the LC-MS/MS technique developed uniquely for this study. The determined HMF content in all tested honey samples did not exceed the applicable standard. All results are within the scope of the European Council Directive 2001/110/EC of 20 December 2001, i.e. they do not exceed HMF content in honey, which is 40 mg/kg.

In this work, two plasmonic structures with two different periodic nanostructures (nanodisk and nanostrip arrays) separated from the gold layer by an ultrathin dielectric Al2O3 layer are proposed, and their optical properties are simulated as 3-dimensional models using COMSOL Multiphysics software tool. The optical responses, such as the amplification of the electric field and the scattering, absorption and extinction cross sections of the two structures, are investigated and compared. The results show that both structures show strong field enhancement in their gap layer, and the structure with the periodic array of metal nanodisks shows stronger field enhancement and larger absorption, extinction, and scattering cross sections in its dipole resonance wavelength, which is defined as a bright plasmonic mode. In addition, some weaker resonant modes are observed for both structures and the reason for their generation is dis-cussed. The analysis of different possible modes in such structures is crucial for their application in various fields.

Materials based on platinum metals with very good catalytic activity were tested in the reduction of p–nitrophenol (pNP) to p–aminophenol (pAP). The majority of presented catalytic materials are based on the adsorption of p–nitrophenol on the surface of the catalyst simultaneously with molecular hydrogen, coming from sodium borohydride in an aqueous medium, which reduces it. In the present paper, a catalytic material based on osmium dispersed in n–decanol or n–dodecanol is presented, which also works as an emulsion membrane, for the absorption of p–nitrophenol and molecular hydrogen at the n–alcohol aqueous solution interface. The hydrogenation of p–nitrophenol is carried out in a reaction and separation column in which the acid receiving phase emulsion is dispersed in the osmium nanodispersion, in n–alcohols. This emulsion circulates from the base of the column to its upper part in co-current or counter-current with the source phase consisting of p–nitrophenol and sodium borohydride. Experiments show that the circulation of counter-current phases is superior to that in co-current, and the emulsion based on n–decanol is more efficient than the one based on n–dodecanol. The increase in the pH difference between the source and receiving phases leads to the increase in the conversion of p–nitrophenol to p–aminophenol. The efficiency of separation of the reaction product in the receiving phase is lower than the conversion at the same operating time. The apparent catalytic rate constant (kapp) of the new catalytic material based on the emulsion membrane with nanodispersion of osmium nanoparticles (0.1×10−3 for n–dodecanol and 0.9×10−3 for n-decanol) is lower by an order of magnitude compared to those based on adsorption on catalysts from platinum metal group. The advantage of the tested membrane catalytic material is that it extracts p–aminophenol in the acid receiving phase. The paper proposes a mechanism of the studied reduction system.

Background: RSV, or respiratory syncytial virus, is a deadly condition that is present all over the world today. The infection is initially contained in the lower respiratory tract without systemic transmission. The objective of the study: Bioinformatics was used in Egypt to create an mRNA vaccine against the Respiratory syncytial virus (RSV). Methodology: In the present screening experimental study, a lipid nanoparticles vaccine of mRNA of the surface fusion protein of Respiratory syncytial virus was manufactured. The present vaccine delivery system was lipid nanoparticles with a particle size of approximately 90 nanometres, manufactured by the hot micro-emulsion method. In stages 1 and 2 of clinical trials, the immunogenicity of the current mRNA RSV vaccine was evaluated. Results: The current vaccine demonstrated 81% immunogenicity in animal testing, but only 69% in stages 1 and 2 of clinical trials. Its side effects were manageable. The results persisted for a while. In the current trial, the vaccination proved effective as a preventative measure against RSV infection. The current vaccination lacked antibody-dependent enhancement, which causes non-protective antibodies to develop. These non-neutralizing antibodies exacerbate infection by activating cytokines and complement cascade through the formation of immune complexes or enhancement of the virus entry and replication in the host cells. On the other hand, the current RSV mRNA vaccine of the surface fusion protein consequent on the production of powerful neutralizing antibodies with prolonged immunity especially to infants and elderly candidates who received the optimal dosage regimen.

Dysregulation of cartilage homeostasis and the changes in the density and the architecture of the subchondral bone were postulated as a potent mechanically pathological activity contributing to osteoarthritis (OA) pathogenesis. Extracorporeal shockwave therapy (ESWT) is a new, none invasive and effective method in the treatment of animal OA model. In the current study, we demonstrated that shockwave induced the expression of protein-disulfide isomerase-associated 3 (Pdia-3) which is a multifunctional protein hypothesized to be a significant mediator for 1α,25-Dihydroxyvitamin D3 (1α,25(OH)₂D₃) signaling pathway using two-dimensional electrophoresis. Histological analysis and quantitative polymerase chain reaction (qPCR) were verified and observed that the expression of Pdia-3 at 2 weeks was significantly higher than that of any other group at 4 weeks, 8 weeks, and 12 weeks post-shockwave treatment in early OA knee of rat. The other factors of the 1α,25(OH)₂D₃ rapid membrane signaling pathway including extracellular signal-regulated protein kinases 1 (ERK1), osteopontin (OPG), alkaline phosphatase (ALP), and matrix metallopeptidase 13 (MMP13) were measured and significantly increased by qPCR at 2 weeks post-shockwave treatment in early OA knee. Our proteomic data revealed significant Pdia-3 expression in microenvironments of joint tissue that could be actively responded to ESWT, which may potentially regulate biological function of chondrocytes and osteoblasts in the treatment of OA knee.

In agriculture, soil-borne fungal pathogens, especially Fusarium oxysporum strains, are posing a serious threat to efforts to achieve global food security. In the search for safer agrochemicals, silica nanoparticles (SiO2NPs) have recently been proposed as a new tool to alleviate pathogen damage including Fusarium wilt. Hollow mesoporous silica nanoparticles (HMSNs), a unique class of SiO2NPs, have been widely accepted as a desired pesticide carrier. However, their role in enhancing the disease resistance and the specific mechanism remain unknown. In this study, three sizes of HMSNs (19, 96 and 406 nm as HMSNs–19, HMSNs–96 and HMSNs–406, respectively) were synthesized and characterized to determine their effects on seed germination, seedling growth, and Fusarium oxysporum f. sp. phaseolus (FOP) suppression in cowpea roots by foliar spray using phenotypes, fresh biomass and disease progression as indicators. The results revealed that three HMSNs exhibited no adverse impacts on seed germination and tended to improve plant growth. Also, they exert their FOP suppression with a size- and concentration-dependent manner. HMSNs–406 possessed the best control effect at a concentration of 1000 mg/L showing an upto 40.00% decline in the disease severity. The Si(OH)4 control was also effective on FOP suppression at a lower concentration of 100 mg/L, whereas its higher concentrations exhibited obviously adverse impacts on FOP control, seed germination and plant growth. Moreover, we conformed that HMSNs posed their Fusarium wilt suppression in cowpea plant by activating SA (salicylic acid)-dependent SAR (systemic acquired resistance) responses rather than directly suppressing FOP. A higher level of SA content and elevated expression of its maker genes of PR-1 and PR-5 in HMSNs–406 treated cowpea roots provided substantial evidences of this mode of action. Other resistance-related genes, as well as defense-responsive enzymes, were also involved in the HMSNs-activated SAR pathway. Overall, for the first time, our results extended a new role of HMSNs as a potent elicitor to serve as a versatile alternative for plant disease protection of low cost, highly efficiency and sustainability.

Soil organic matter (SOM) is important for the global carbon cycle, and hyperspectral remote sensing has proven a promising method for fast SOM content estimation. However, soil physical properties significantly affect the sensitivity of satellite hyperspectral imaging to SOM, leading to poor generalization ability of the estimation model. This study aims to improve the spatiotemporal transferability of the SOM prediction model by alleviating the coupling effect of soil physical properties on the spectra. Based on satellite hyperspectral images and soil physical variables, including soil moisture (SM), soil surface roughness (root mean squared height, RMSH), and soil bulk weight (SBW), a soil spectral correction strategy was established based on the information unmixing method. Two important grain-producing areas in Northeast China were selected as study areas to verify the performance and transferability of the spectral correction model and SOM content prediction model. The results showed that soil spectral corrections based on fourth-order polynomials and the XG-Boost algorithm had excellent accuracy and generalization ability, with residual predictive deviations (RPD) exceeding 1.4 in almost all bands. In addition, when the soil spectral correction strategy was adopted, the accuracy of the SOM prediction model and the generalization ability after model migration were significantly improved. The SOM prediction accuracy based on the XG-Boost corrected spectrum was the highest, with a coefficient of determination (R2) of 0.76, root mean square error (RMSE) of 5.74 g/kg, and RPD of 1.68. The prediction accuracy, R2, RMSE, and RPD of the model after migration were 0.72, 6.71 g/kg, and 1.53, respectively. Compared with the direct migration prediction of the model, adopting the soil spectral correction strategy based on fourth-order polynomials and XG-Boost reduced the RMSE of the SOM prediction results by 57.90% and 60.27%, respectively. The performance comparison highlighted the advantages of considering soil physical properties in regional-scale SOM prediction.

Abstract: Two novel low-dimensional molecular magnetic materials were prepared by a self-assembling of 3d- and 5d-metal complexes. These are the first neutral heterobimetallic cyanobridged compounds involving one anisotropic Mn(III) Schiff base complex and one octacyanotungstate(V) per molecular unit. A slow diffusion of the constituents’ solutions leads to a formation of the 0D crystalline complex 1 due to coordination of a water molecule to the Mn center prevents a polymer formation. A rapid mixing of reagents results in a precipitation of the microcrystalline powder of the complex 2, which on a totality of experimental data possess 1D polymeric structure. The magnetic studies have shown that antiferromagnetic exchange interactions are dominating in 1 J/k_B= -13.1(7) K, D=-3.0(1.3) K, zJ'= -0.16(20) K and g_av=2.00(1); while the presence of the significant intramolecular Mn(III)–W(V) ferromagnetic couplings through cyanide bridges is characteristic for 2 (J/k_B = 46.1(5) K g_Mn = 2.11(3), fixed g_W = 2.0). Due to the weak interchain interactions, zJ'/k_B = –0.8(2) K, compound 2 is a metamagnet with the Néel temperature of 9.5 K undergoing a spin-flip transition at 2 kOe. The slow magnetization dynamics of 2 was investigated at DС field of 0 and 2 kOe, giving the values of τ₀ 32(15) and 36(15) ps respectively, well within the range typical for SCMs. The respective ∆_τ/k_B values were 48.4(1.2) and 44.9(1.0) K.

Honey is a sweet substance extensively consumed in the world for its nutritional and healthy properties. However, residues of pesticides and environmental contaminants can compromise its quality. For this reason, the physicochemical parameters, and the organic contamination of monofloral and multifloral honeys from three regions of Algeria (Tiaret, Laghouat and Tindouf) were monitored to evaluate the quality of honey and the safety for consumers. In general, the results obtained from the physicochemical analyses were in line with the EU standards. In terms of contamination, pesticides authorised and used in Algerian agriculture (matalaxyl-M and cyromazine), as well as banned pesticide (carbaryl), were found in almost all the samples. However, only the concentration of cyromazine was higher than the relative EU maximum residue levels. PCB 180, PCB 189, anthracene, fluorene and phenanthrene were mainly detected. All the honeys show traces of DiBP, DBP, DEHP and DEHT, but no traces of bisphenols were found. Moreover, the dietary exposure assessment shows that a small amount of Algerian honey can be safely consumed. Overall, data from this study should motivate the Algerian government to enhance their monitoring activities in beekeeping and to find solutions for implementing more sustainable agricultural practices harmonizing with the international legislation.

Indole is a versatile pharmacophore widely distributed in bioactive natural products. This privileged scaffold has been found in a variety of molecules isolated from marine organisms such as algae and sponges. Among these, indole alkaloids represent one of the biggest, most promising family of compounds, having shown a wide range of pharmacological properties, including anti-inflammatory, antiviral and anticancer activities. The aim of this review is to show the current scenario of marine indole alkaloid derivatives, covering not only the most common chemical structures, but also new synthetic routes developed during the last years as well as promising therapeutic applications.

Biological nanoparticles (NPs), such as extracellular vesicles (EVs), exosome-mimetic nanovesicles (EMNVs) and nanoghosts (NGs), are perspective non-viral delivery vehicles for all types of therapeutic cargo. Biological NPs are renowned for their exceptional biocompatibility and safety, alongside their ease of functionalization, but a significant challenge arises when attempting to load therapeutic payloads, such as nucleic acids (NAs). One effective strategy involves fusing biological NPs with liposomes loaded with NAs, resulting in hybrid carriers that offer the benefits of both biological NPs and the capacity for high cargo loads. Despite their unique parameters, one of the major issues of virtually any nanoformulation is the ability to escape degradation in the compartment of endosomes and lysosomes which determines the overall efficiency of nanotherapeutics. In this study, we fabricated all major types of biological and hybrid NPs and studied their response to acidic environment observed in endolysosomal compartment. In this study, we show that EMNVs display increased protonation and swelling relative to EVs and NGs in an acidic environment. Furthermore, the hybrid NPs exhibit an even greater response compared to EMNVs. Short-term incubation of EMNVs in acidic pH corresponding to late endosomes and lysosomes again induces protonation and swelling, whereas hybrid NPs are ruptured, resulting in the decline of their quantities. Our findings demonstrate that in an acidic environment, there is enhanced rupture and release of vesicular cargo observed in hybrid EMNVs that are fused with liposomes compared to EMNVs alone. This was confirmed through PAGE electrophoresis analysis of mCherry protein loaded into nanoparticles. In vitro analysis of NPs colocalization with lysosomes in HepG2 cells demonstrated that EMNVs mostly avoid endolysosomal compartment whereas hybrid NPs escape it over time. To conclude, (1) hybrid biological NPs fused with liposomes appear more efficient in the endolysosomal escape via the mechanism of proton sponge associated with scavenging of protons by NPs, influx of counterions and water, and rupture of endo/lysosomes, but (2) EMNVs are much more efficient than hybrid NPs in actually avoiding endolysosomal compartment in human cells. These results reveal biochemical differences across four major types of biological and hybrid NPs, and indicate that EMNVs are more efficient in escaping or avoiding endolysosomal compartment.

This study explores the complexities involved in the extraction and purification of catechins, prominent bioactive compounds found in plant extracts and tea. It addresses challenges arising from the intricate molecular structure of catechins and their inherent variability across botanical sources. Despite these obstacles, catechins present significant potential, particularly in healthcare. Their potent antioxidant properties have been extensively investigated and associated with numerous health benefits, positioning them as promising therapeutic agents for combating chronic diseases. Furthermore, catechins have diverse applications across various industries, including food and beverage, cosmetics, agriculture, and materials science. This abstract emphasizes the importance of continued research and innovation in catechin extraction and utilization, which hold promise for advancing human health and technological progress across multiple domains.

This study investigated the ability of a HYDRUS 1D model for predicting the vertical distribution of potassium iodine (200 ppm) in soil columns after amendment with five different common remediation materials (gypsum, lime, fly ash, charcoal and sawdust) at a rate of 2.5% (w/w), relative to an unamended control soil. Results shows that relative to the unamended soil, iodine leaching was decreased by all amendments but that the magnitude of the decreases varied with the soil amendment applied. Iodine content was highest in the upper layer of the soil columns and decreased progressively with soil depth. The model was evaluated via comparison of the model simulated values with measured values from the soil column studies. The results showed that the HYDRUS 1D model efficiency was near to 1, indicating that the stimulated results were near to the measured values. Therefore, this study showed that iodine leaching through a soil could be ascertained well using a HYDRUS 1D model. The model over predicted iodine leaching, resulting to a weak correspondence between the simulated and the measured results for iodine leaching. This suggests that the HYDRUS-1D model does not explain accurately different organic and inorganic amended soil and the preferential flow that occurs in these columns. This may be due to the fact that Freundlich isotherm, which is part of the transport equations, does not sufficiently describe the mechanism of iodine adsorption onto the soil particles. This study would help to select amendments for an effective management strategy to reduce exogenous iodine losses from agro-ecosystems. This would also improve understanding of iodine transport in soil profile.

To compare The effects of organic and inorganic impregnation on the properties of unmodified, phenol formaldehyde oligomer-modified (PFOMCF), and sodium silicate-modified Chinese fir wood (SSMCF) were compared using samples prepared using the respiratory impregnation method. Impregnation and reinforcement effects and water resistance of PFOMCF and SSMCF were compared and the results was showed that the weight percentage gain, density increase rate, bending strength, and compressive strength of SSMCF were clearly higher than those of PFOMCF and had a lower water absorption rate within 60 h. The impregnation and reinforcement effects and dimensional stability of SSMCF were better than those of PFOMCF. FT-IR, XRD, CONE, and TGA examinations were used to test and analyze the chemical structure, crystalline structure, flame retardancy, and heat resistance of these modified woods. The results indicated that SSMCF possessed more hydrogen bonds than PFOMCF and that Si–O–Si chemical bonding with high bond energy was formed. Meanwhile, the weakened degree of the diffraction peak of SSMCF was much less than that of PFOMCF. These results explained that the mechanical properties and water resistance of SSMCF were better than PFOMCF. Compared with PFOMCF, SSMCF had a lower heat release rate (HRR), peak-HRR, mean-HRR, total heat release, smoke production rate, and total smoke production as well as higher thermal decomposition temperature and residual rate. Inorganic sodium silicate was shown to be a better flame retardant, while SSMCF had good smoke suppression effects, thermal stability, and safety performance in the case of fire.

Background and Objectives: The purpose of this study was to investigate whether early surfactant administration affects the status of ductus arteriosus (DA) in preterm infants ≤32 weeks of gestational age (GA) within 24 hours of birth. Materials and Methods: It is a prospective study conducted from March 15, 2022, to November 15, 2023, in a tertiary academic center. In-born infants ≤ 32 weeks of gestation (n = 88) were enrolled. The study group was further divided into surfactant (n=44) and non-surfactant (n=44) subgroups. Results: 76% of the preterm infants who received surfactant therapy (RRR = 0.839) recorded an increase in Kindler Score at 24 hours of life (1-RR = 1-0.24 = 76%). Surfactant administration was significantly associated with decreased pre-ductal diastolic pressure (29.9 mmHg vs. 34.8 mmHg, p=0.0231), post-ductal diastolic pressure (28.7 mmHg vs. 32.2 mmHg, p=0.0178) pre-ductal MAP (41.6 mmHg vs. 46.5 mmHg, p=0.0210) post-ductal MAP (41.0 mmHg vs. 45.3 mmHg, p=0.0336). There were no significant changes in ductus arteriosus parameters at 24 hours of life. Conclusions: Early surfactant administration does not affect the status of ductus arteriosus in preterm infants ≤32 weeks of gestational age at 24 hours of life.

Copper(II), nickel(II) and zinc(II) complexes of various peptide fragments of tau protein were studied by potentiometric and spectroscopic techniques. All peptides contained one histidyl residue and represented the sequences of tau(91-97) (Ac-AQPHTEI-NH2), tau(385-390) (Ac-KTDHGA-NH2) and tau(404-409) (Ac-SPRHLS-NH2). Imidazole-N donors of histidine were the primary metal binding sites for all peptides and all metal ions but in case of copper(II) and nickel(II) the deprotonated amide groups were also involved in metal binding by increasing pH. The most stable complexes were formed with copper(II) ion but the presence of prolyl residues resulted in significant changes in the thermodynamic stability and speciation of the systems. It was also demonstrated that nickel(II) and especially zinc(II) complexes have relative low thermodynamic stability with these peptides. Copper(II) catalyzed oxidation of the peptides was also studied. In the presence of H2O2 the fragmentation of peptides can be detected in all cases. In the simultaneous presence of of H2O2 and ascorbic acid the extent of the fragmentation of the peptide is less preferred, and the formation of 2-oxo-histidine also occurs.

One of the most concerning global environmental issues is the pollution of agricultural soils by heavy metals (HMs), especially cadmium (Cd), which not only affects human health by taking Cd-containing foods but also impacts the quality of rice. The soil's nitrification and denitrification processes, coupled with the release of volatile organic compounds by plants, raise substantial concerns. The understanding of three aspects of paddy soil under conditions of heavy-metal pollution and water management is currently limited. In this review, we summarized recent literature related to the deleterious effects of Cd on both soil processes related to the N cycle and rice quality, particularly aroma, in different water management practices. Under both continuous flooding (CF) and alternate wetting and drying (AWD) conditions, cadmium (Cd) has been observed to reduce both nitrification and denitrification processes. The adverse effects are more pronounced in continuous flooding (CF) compared to alternate wetting and drying (AWD). Similarly, the alteration in rice aroma is more significant in AWD than in CF. The precise modulation of volatile organic compounds (VOCs) by Cd, remains unclear based on the available literature. Nevertheless, HM accumulation is higher in AWD conditions compared to CF, leading to a detrimental impact on volatile organic compounds (VOCs). The literature concluded that AWD practices should be avoided in Cd contaminated fields to decrease accumulation and maintain the quality of rice. In the future, rhizospheric engineering and plant biotechnology can be used to decrease the transport of HMs from the soil to the plant’s edible parts.

This study used the sol–gel method to synthesize a non-halogenated hyperbranched flame retardant containing nitrogen, phosphorus and silicon, HBNPSi, which was then added to a polyurethane (PU) matrix to form an organic–inorganic hybrid material. Using 29Si nuclear magnetic resonance, energy-dispersive X-ray spectroscopy of P- and Si-mapping, scanning electron microscopy, and X-ray photoelectron spectroscopy, this study determined the organic and inorganic dispersity, morphology, and flame retardance mechanism of the hybrid material. The condensation density of the hybrid material PU/HBNPSi was found to be 74.4%. High condensation density indicates a dense network structure of the material. The P- and Si-mapping showed that adding inorganic additives in quantities of either 20% or 40% results in homogeneous dispersion of the inorganic fillers in the polymer matrix without agglomeration, indicating that the organic and inorganic phases had excellent compatibility. In the burning test, adding HBNPSi to PU resulted in the material passing the UL-94 standard at the V2 level, unlike the pristine PU, which did not meet the standard. The results demonstrated that after non-halogenated flame retardant was added to PU, the material’s flammability and dripping were lower, thereby proving that flame retardants containing elements such as nitrogen, phosphorus, and silicon exert an excellent flame retardant synergistic effect.

Polyphenols are the most common organic compounds in wine. They improve both the sensory aspects of wine and human health by activating antioxidant systems. Therefore, there is a great need for a simple, fast and accessible method to determine the polyphenol content of wine. The aim of this study is to characterize polyphenolic compounds in natural wine samples using an electrochemical method and a modified carbon paste electrode with TiO2 nanoparticles. This work is motivated by the promising improvement of the sensing properties of a TiO2 nanoparticle-modified carbon paste electrode observed in the electrooxidation of different polyphenols. Since the voltammetric response of wine is largely irreversible, another motivation was the possibility of improving the processing of voltammograms to obtain data indicative of wine polyphenols, based on the approach described in the seminal work by Espinoza et al. The modified electrode studied provides an improved and reproducible voltammetric response of gallic acid in wine samples and provides a good basis for further development of an integrated sensor/data system with the possibility of wider application for the quantification of gallic acid as a flavor and visually relevant parameter in winemaking.

Air pollution and the increasing production of greenhouse gases has prompted greater use of renewable energy sources; the EU has set the use of green energy at 32 percent by 2030. With this in mind, in the last 10 years the demand for pellets in Italy has more than doubled making Italy the second largest consumer in Europe. The quality of the pellets burned in stoves is crucial to indoor and outdoor pollution. Among other parameters, moisture and ash are used to classify pellets according to EN ISO 17225:2014. This work involved the analysis of the organic and inorganic fraction of both some finished products on the Italian market and some raw materials (e.g., wood chips) sampled according to the technical standard EN 14778:2011. The analytical results showed the presence of some substances potentially harmful to human health such as formaldehyde, acetone, toluene and styrene for the organic fraction and nickel, lead and vanadium for the inorganic fraction. The chemometric approach showed that it is the inorganic fraction which is most responsible for the diversification of the samples under study. The detection of some substances may be a warning bell about the impact of such materials both for the environment and for the human health.

Curcumin, a hydrophobic polyphenol compound derived from the rhizome of the Curcuma genus, has a wide spectrum of biological and pharmacological applications. Previously, curcumin nanoparticles with different stabilizers had been produced successfully in order to enhance solubility and per oral absorption. In the present study, we tested the anti-inflammatory effect of D-α-Tocopheryl polyethylene glycol 1000 succinate (TPGS)-stabilized curcumin nanoparticles in vivo. Lambda-carrageenan (λ-carrageenan) was used to induce inflammation in rats; it was given by an intraplantar route and intrapelurally through surgery in the pleurisy test. In the λ-carrageenan-induced edema model, TPGS-stabilized curcumin nanoparticles were given orally one hour before induction and at 0.5, 4.5, and 8.5 h after induction with two different doses (1.8 and 0.9 mg/kg body weight (BW)). Sodium diclofenac with a dose of 4.5 mg/kg BW was used as a standard drug. A physical mixture of curcumin-TPGS was also used as a comparison with a higher dose of 60 mg/kg BW. The anti-inflammatory effect was assessed on the edema in the carrageenan-induced paw edema model and by the volume of exudate as well as the number of leukocytes reduced in the pleurisy test. TPGS-stabilized curcumin nanoparticles with lower doses showed better anti-inflammatory effects, indicating the greater absorption capability through the gastrointestinal tract.

Crash prediction of the sharp horizontal curve segment (SHCS) of a freeway is an important tool in analyzing safety of SHCSs and in building a crash prediction model (CPM). The design and crash report data of 88 SHCSs from different institutions were surveyed and three negative binomial (NB) regression models and three generalized negative binomial (GNB) regression models were built to prove that the interactive influence of explanatory variables plays an important role in fitting goodness. The study demonstrates the effective use of the GNB model in analyzing the interactive influence of explanatory variables and in predicting freeway basic segments. Traffic volume, highway horizontal radius, and curve length have been formulated as explanatory variables. Subsequently, we performed statistical analysis to determine the model parameters and conducted sensitivity analysis. Among the six models, the result of model 6, which considered interactive influence, is much better than those of the other models by fitting rules. We also compared the actual results from crashes of 88 SHCSs with those predicted by models 1, 3, and 6. Results demonstrate that model 6 is much more reasonable than models 1 and 3.

From grape cultivation to ripening and harvest timing to processing, each step can be a critical point when it comes to wine quality and phenolic composition. In this study, the influence of winemaking technology on resveratrol and quercetin content, as well as other polyphenolic compounds, was investigated. Resveratrol is a non-flavonoid polyphenolic stilbene synthesized by grape skin when damaged by infectious diseases or ionizing radiation. Quercetin is a phenol found in grape skins and stems and is produced to protect grapes from UV light damage. Trans-resveratrol and quercetin are known to act as antioxidants, reduce the risk of atherosclerosis and type 2 diabetes, inhibit the growth of cancer cells, and prevent the release of allergic and inflammatory molecules. However, the question was whether red wine could be enriched with these phenols using an innovative winemaking technology. The innovative idea was to completely replace the cold maceration process with maceration with the addition of wild yeast (Torulaspora delbrueckii, Td). Maceration with the addition of wild yeast (Td) offers the following advantages over traditional cold maceration: (1) higher concentrations of trans-resveratrol (>35-40%) and quercetin (>35-40%) in the final wine, (2) the new wine has a higher potential for human health, (3) the wine has a better aroma and stability due to the higher mannoprotein content, and (4) the better energy efficiency in the production process. The study of stability during storage and aging also included derivatives of benzoic acid and hydroxycinnamic acid, piceid, catechin, naringenin, rutin, kaempherol, hesperetin, and anthocyanins. The study found that younger wines had higher phenolic content, while storage of the wine resulted in a decrease in total phenolic content, especially monomeric stilbenes and quercetin.

The influence of the ligands in coupled organic-inorganic nanostructures (COINs) on the performance of optoelectronic devices is investigated. We fabricated photodiodes based on pentacene and PbS nanocrystals coupled to organic ligands like 1,2-ethanedithiol (EDT) and tetrabutylammonium iodide (TBAI) and a combination of both, EDT and TBAI, as a heterostructure. These ligands were first separately used to fabricate single ligand-type of organic-inorganic devices and later compared with a heterostructure of PbS-EDT and PbS-TBAI. To tune the optical energy gap of COINs to align with the triplet level of pentacene, it was necessary to choose a suitable particle size. For this purpose, ultraviolet photo-emission spectroscopy (UPS) was used to determine the energy of the highest occupied molecular orbital (HOMO) and the work function of COINs, while the energy of the lowest unoccupied molecular orbital (LUMO) of COINs was estimated subsequently by adding the exciton binding energy and the optical band gap to the measured HOMO energy. Devices with heterostructure COINs achieve a higher short circuit current than COINs with a single type of the ligands. Finally, even if the requirements of proper energy level alignment are satisfied, the photodiodes' performance was affected by the morphology of COINs. This finding has been demonstrated by atomic force microscopy (AFM) and transmission electron microscopy (TEM). Incident photon to current efficiency (IPCE) shows a shift for the excitonic absorption peaks in the visible range at opposite applied voltages. The IPCE signal for the double heterostructure device is higher than the single type device.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

The present study was conducted to investigate the comparative effects of organic and inorganic forms of sulfur, methyl sulfonyl methane (MSM) and sodium sulfate (SS), on laying performance, egg quality, ileal morphology, ileal volatile fatty acids, and antioxidant and stress markers in various biological samples in aged laying hens. A total of 144, 73-week-old Lohman Brown-Lite laying hens were randomly assigned to one of three experimental diets: basal diet (CONT), CONT + 0.2% MSM (MSM), and CONT + 0.3% SS (SS). The trial lasted for 12 weeks. MSM and SS groups contained 0.07% of sulfur, either organic or inorganic. Dietary MSM did not affect egg production and feed conversion ratio at 12 weeks compared with the CONT group. Dietary sulfur did not affect egg quality except for Haugh unit at 4 weeks which was lowered (P &lt; 0.05) in the SS group. Compared with the CONT group, higher (P &lt; 0.05) villus height and crypt depth ratio was observed in the SS group. None of dietary sulfur affected the percentages of short-chain fatty acids in the ileum. Total antioxidant capacity of liver increased (P &lt; 0.05) in laying hens fed MSM- and SS-added diets compared with the CONT group. The MSM and SS groups lowered (P &lt; 0.05) malondialdehyde (MDA) concentration in serum samples compared with the CONT. Finally, dietary MSM had the lowest (P &lt; 0.05) MDA concentrations in yolk samples. Taken together, our study showed that dietary organic and inorganic sulfur have positive effects on ileal morphology and antioxidant capacity in laying hens. However, SS-mediated inhibition in laying performance needs to be clarified.

Simple Summary: The distribution of typical bacterial redox enzymes such as pyruvate-ferredoxin oxidoreductase (PFOR) in protozoa remains interestingly puzzling. Previous studies have demonstrated diverse cellular localizations of PFOR in some amitochondriate anaerobic protozoa. PFOR is of particular pharmacological importance because it catalyzes the reductive bio-activation of nitro-based prodrugs to cytotoxic radical metabolites. Metronidazole was developed primarily as an antiprotozoal agent against infections caused by Trichomonas vaginalis. However, its antimicrobial spectrum was subsequently expanded to cover anaerobic bacterial infections. It has been shown that mutations in the genes encoding PFOR result in inherent resistance of PFOR-possessing anaerobic protozoa and bacteria to nitro-based prodrugs. Deciphering the evolutionary history of PFOR is crucial in deepening our understanding of the evolution of anaerobic pathogens and unfold new approaches for drug discovery and targeting in pathogen chemotherapy. Abstract: The present frontrunners in the chemotherapy of infections caused by protozoa are nitro-based prodrugs that are selectively activated by PFOR-mediated redox reactions. This study seeks to analyze the distribution of PFOR in selected protozoa and bacteria by applying comparative bioinformatics approaches to test the hypothesis that PFOR was most likely acquired through horizontal gene transfer (HGT) from bacteria. Furthermore, to identify other genes that were putatively acquired using proteome-wide and gene expression analyses. A plausible explanation for the patchy occurrence of PFOR in protozoa is based on the hypothesis that bacteria are potential sources of genes that enhance optimal adaptation of protozoa in hostile environments. The exclusively expressed proteins obtained from Entamoeba histolytica and the putative gene donor, Desulfovibrio vulgaris, showed an over-expression of eleven genes involved in intermediary metabolism. If these results can be reproduced in other PFOR-possessing protozoa, it would provide a more validated evidence to support the horizontal transfer of pfor from bacteria.

Extra virgin olive oil (EVOO) is recognized for its numerous health benefits attributed to its rich phenolic components. NMR has emerged as a prevalent technique for precisely identifying these compounds. Among Mediterranean countries, Greece stands as the third-largest producer of olives, with the Epirus region notably advancing in olive cultivation, contributing significantly to the dynamic growth of the region. In this study, an NMR method was employed based on the acquisition of an 1H NMR spectrum along with the multiple resonant suppression in order to increase the sensitivity. Using the above method, 198 samples of extra virgin olive oil, primarily sourced from the Epirus region were analyzed and both the qualitative and quantitative aspects of phenolic compounds were acquired. In addition, we examined the effect of various factors, such as, variety, harvest month and region origin on the phenolic compounds’ concentration. The results revealed an average total phenolic content of 246 mg/kg, closely approaching the EU health claim limit of 250 mg/kg. Approximately 15% of the samples were confidently characterized as high-phenolic olive oil. The highest concentrations were observed in Thesprotia samples, with several Lianolia variety exceeding the total phenolic content of 400 mg/kg. Statistical tests demonstrated a significant influence of the olive variety and the month of fruit harvest on phenolic component concentration, followed by the region of origin. A very strong correlation was noted between the total phenolics content and the levels of oleocanthal and oleacein, with a correlation coefficient (r) of 0.924. Upon optimization of all factors affecting olive oil quality, the majority of EVOO from the Epirus region have the potential to be characterized as high in phenolic content.

Elevated carbon dioxide (eCO₂) stimulates wheat grain yield, but simultaneously reduces protein (N) concentration. Also other essential nutrients are subject to change. This study is a comprehensive synthesis of wheat experiments with eCO₂, estimating effects on N, minerals (B, Ca, Cd, Fe, K, Mg, Mn, Na, P, S, Zn), and starch. Analysis was made by i) deriving response functions for the relative effect on element concentration in relation to CO₂ concentration, ii) meta-analysis to test the magnitude and significance of observed effects, and iii) relating CO₂ effects on minerals to effects on N and grain yield. Responses range from zero to strong negative effects of eCO₂ on mineral concentration, with largest reductions for the nutritionally important elements N, Fe, S, Zn and Mg. Together with the positive but small and non-significant effect on starch concentration, the large variation in effects suggests that CO₂-induced responses cannot be explained by a simple dilution model. To explain the observed pattern, uptake and transport mechanisms may have to be considered, along with the link of different elements to N uptake. Our study shows that eCO₂ has a significant effect on wheat grain stoichiometry, with implications for human nutrition in a world of rising CO₂.

Mechanical ventilation (MV), used in patients with acute lung injury (ALI), induces diaphragmatic myofiber atrophy and contractile inactivity, termed ventilator-induced diaphragm dysfunction. Phosphoinositide 3-kinase- (PI3K-) is crucial in modulating fibrogenesis during the reparative phase of ALI; however, the mechanisms regulating the interactions among MV, myofiber fibrosis, and PI3K- remain unclear. We hypothesized MV with or without bleomycin treatment would increase diaphragm muscle fibrosis through the PI3K- pathway. Five days after receiving a single bolus of 0.075 units bleomycin intratracheally, C57BL/6 mice were exposed to 6 or 10 mL/kg MV for 8 h after receiving 5 mg/kg of AS605240 intraperitoneally. In wild-type mice, bleomycin exposure followed by MV 10 mL/kg prompted significant increases in disruptions of diaphragmatic myofibrillar organization, transforming growth factor-1, oxidative loads, Masson’s trichrome staining, extracellular collagen levels, positive staining of -smooth muscle actin, PI3K- expression, and myonuclear apoptosis (P &lt; 0.05). Decreased diaphragm contractility and peroxisome proliferator activated receptor- coactivator-1 levels were also observed (P &lt; 0.05). MV-augmented bleomycin-induced diaphragm fibrosis and myonuclear apoptosis were attenuated in PI3K-γ-deficient mice and through AS605240-induced inhibition of PI3K- activity (P &lt; 0.05). MV-augmented diaphragm fibrosis after bleomycin-induced ALI is partially mediated through PI3K-γ. Therapy targeting PI3K-γ may ameliorate MV-associated diaphragm fibrosis.

Abstract: Toxicity of emerging organic pollutants to photosystems of aquatic plants are still not well clarified. This study aimed to develop a novel ecotoxicological experimental protocol based on nanoscale electrochemical mapping of photosynthetic oxygen evolution of aquatic plants by SECM (scanning electrochemical microscopy). The protocol was also checked by confocal laser scanning microscopy (CLSM), the traditional Clark oxygen electrode method and chlorophyll fluorescence technique. The typical persistent organic pollutant 2,4-dichlorophenol (2,4-DCP) in water environment and the common aquatic Microsorium pteropus (M. pteropus) were chosen as the model organic pollutant and tested plant, respectively. It was found that the SECM method could well discriminated the responses of stoma micromorphology and spatial pattens of photosynthetic oxygen evolution on single stoma. The shape of stoma blurred with increasing 2,4-DCP concentration, which was in good agreement with the CLSM images. The dose-response curves and IC50 values obtained from the SECM data were verified by the data measured by the traditional Clark oxygen electrode method and chlorophyll fluorescence test. The IC50 value of single stoma oxygen emission of 24 h exposed plant leave, which was derived from the SECM current data (32535 μg L-1), was close to those calculated from the maximum photosynthetic efficiency (Fv/Fm) measured by chlorophyll fluorescence test (33963 μg L-1), and the Clark oxygen electrode method photosynthetic oxygen evolution rate (32375 μg L-1). The 72 h and 96 h 2,4-DCP exposure data further confirmed the reliability of the nanoscale stoma oxygen emission mapping methodology for ecotoxicological assessment. In this protocol, the procedures for how to collect effective electrochemical data and how to extract useful information from the single stoma oxygen emission pattern were well established. This study showed that SECM is a feasible and reliable ecotoxicological tool for evaluation of toxicity of organic pollutants to higher plants with unique nanoscale visualization advantage over the conventional methods.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

The study was carried out to determine the influence of organic and inorganic fertilizers on maize yield and soil fertility; to determine economically optimum organic and inorganic fertilizer combinations for maize production. The study was performed in a randomized complete block design consisting of 10 treatments and 3 replications. The treatments were: Control, 100% of R-NP (138 N and 92 P), 100% of vermicompost,100% of conventional compost, 25% R-NP +75% of vermicompost, 50% of R-NP + 50% of vermicompost, 75% of R-NP+25% of from vermicompost, 25% of R-NP +75% of conventional compost, 50% of R-NP+50% of conventional-compost, 75% of R-NP +25% of conventional-compost. All rates of vermicompost and conventional compost were applied based on N equivalence. Results indicate that applications of inorganic fertilizers with a combination of organic source fertilizers were increases maize yield and yield components and improves the nutrient status of the soil. The highest maize grain yield (7494.3 kg ha-1) and above-ground biomass yield (18718.0 kg ha-1) were obtained from the applications of 50% recommended NP fertilizer plus 50% vermicompost which is based on the recommended N equivalent respectively. Similarly, we found that a combination of both inorganic and organic fertilizers application also is the best strategy to improve major soil nutrients, maintain soil fertility. The economic analysis revealed that the highest net benefit of (108,872.0 ETB ha-1) was obtained from the application of 50% recommended NP fertilizer plus 50% vermicompost based on the recommended N equivalence. Yet, the lowest yield and net benefit value were attained from the control or unfertilized plot. Therefore, this study suggests that an appropriate proportion of organic fertilizer with inorganic fertilizer not only for higher yield maize production with an assurance of potential economic returns to the small hold farmers but also improve and maintain the soil fertility and should be adopted with similar soil type and agro-ecologies.

Batch and transport experiments were used to investigate the remediation of a loamy sand soil contaminated with Cr(VI) using zero valent iron nanoparticles (nZVI) stabilized by the carboxy methyl cellulose (CMC-nZVI). The effect of pH, ionic strength (IS), and flow rate on the removal efficiency of Cr(VI) were investigated under equilibrium (uniform transport) and non-equilibrium (Two-site sorption) transport using the Hydrus-1D model. The overall removal efficiency ranged from 70 to over 90% based on the chemical characteristics of the CMC-nZVI suspension and the transport conditions. The concentration and pH of the CMC-nZVI suspension had the most significant effect on the removal efficiency and transport of Cr(VI) in the soil. The average removal efficiency of Cr(VI) was increased from 24.1 to 75.5% when the concentration of CMC-nZVI nanoparticles was increased from 10 to 250 mg L-1, mainly because of the increased total surface area at larger particle concentration. Batch experiments showed that removal efficiency of Cr(VI) was much larger under acidic conditions. The average removal efficiency of Cr(VI) reached 90.1 and 60.5 % at pH 5 and 7, respectively. The Two-site sorption model described quite well (r2 = 0.96-0.98) the transport of Cr(VI) in soil as compared to the uniform transport model (r2 = 0.81-0.98). The average retardation of Cr(VI) was 3.51 and 1.61 at pH 5 and 7, respectively, indicating earlier arrival for the breakthrough curves and shorter time to reach maximum relative concentration at lower pH. The Hydrus-1D model has proven to be an efficient tool for assessing the removal of Cr(VI) pollutants, offering innovative, cost-effective, and environmentally friendly remediation methodologies.

Outbreaks of the crown-of-thorns seastar (CoTS) represent a major cause of coral loss on the Great Barrier Reef. Outbreaks might be explained by enhanced larval survival supported by higher phytoplankton availability after flood events, yet little is known about CoTS larvae feeding behaviour, in particular their potential for selective feeding. Here, single- and mixed-species feeding experiments were conducted on CoTS bipinnaria larvae using five algae (Phaeodactylum tricornutum, Pavlova lutheri, Tisochrysis lutea , Dunaliella sp. and Chaetoceros sp.) and two algal concentrations (1000 and 2500 algae mL^-1). Cell counts using flow-cytometry at the beginning and end of each incubation experiment allowed us to calculate the filtration and ingestion rates of each species by CoTS larvae. In line with previous studies, CoTS larvae ingested more algae when initial algal concentration was higher. We found evidence for the selective ingestion of some species (Chaetoceros sp., Dunaliella sp.) over others (P. lutheri, P. tricornutum). The preferred algal species had the highest energy content, suggesting that CoTS selectively ingested the most energetic algae. Ultimately, combining these results with spatio-temporal patterns in phytoplankton communities will help elucidate the role of larval feeding behaviour in determining the frequency and magnitude of CoTS outbreaks.

The treatment of acute myeloid leukemia (AML) with adverse genetics remains unsatisfactory, with very low response rates to standard chemotherapy and shorter durations of remission commonly observed in these patients. The complex biology of AML with adverse genetics is continuously evolving. Herein, we discuss recent advances which have investigated the contribution of cell intrinsic mechanisms as well as of the immune system to myeloid leukemogenesis in this specific subset of AML. We focus on the biological rationales for combining targeted therapy and immunotherapy, which are currently being investigated in ongoing trials, and could hopefully ameliorate the poor outcomes for these patients

The purpose of these studies was to investigate effect of selenate (Se6), selenized yeast (SeYe) and carnosic acid (CA) supplementation to the diet containing fish oil (F-O) and rapeseed oil (R-O) on contents of fatty acids (FA), malondialdehyde (MDA), tocopherols (Ts) and total cholesterol (TCh) in lambs’ spleens. 24 male lambs (4 groups per 6 animals) have been fed: the control diet - the basal diet (BD) enriched in F-O and R-O; the CA diet - BD enriched in F-O, R-O and CA; the SeYeCA diet - BD enriched in F-O, R-O, CA and SeYe; the Se6CA diet - BD enriched in F-O, R-O, CA and Se6. Dietary modifications affected profiles of FA in spleens. The SeYeCA and Se6CA diets increased the docosapentaenoic acid preference in Δ4-desaturase, hence the higher content of docosahexaenoic acid was found in spleens of SeYe- or Se6-treated lambs than in spleens of animals receiving the CA and control diets. Experimental diets reduced the level of atherogenic FA in the spleen in comparison with the control diet. The experimental diets supplemented with SeYe or Se6 increased levels of TCh and Ts in spleens in comparison with the CA and control CA diets. The present studies documented that Se6, SeYe and CA influenced the metabolism of FA, Ts and cholesterol in spleens.

Spectral characteristics of CDOM in water column are a key parameter for bio-optical modeling. Knowledge of CDOM optical properties and spatial discrepancy based on the relationship between water quality and spectral parameters in Yinma River watershed with in situ data collected highly-polluted waters are exhibited in this study. Seasonal field data sets collected over a period of 2 months in 2015 in Yinma River Watershed. Based on the comprehensive index method, the riverine waters showed serious contamination, especially the COD, Fe, Mn, Hg and DO were out of range contamination warning. Dissolved organic carbon (DOC) and total suspended matter (TSM) with prominent non-homogenizing were significantly high in the riverine waters, but chlorophyll-a (Chl-a) was opposite. Ternary phase diagram showed that non-algal paritcles absorption played an important role in total non-water light absorption (>50%) in most sampling locations, and mean contribution of CDOM were 13% and 22% in summer and autumn respectively. Analysis of ratio of absorption at 250-365 nm (E_250:365) and spectral slope (S_275-295) indicated that CDOM had higher aromaticity and molecular weight in autumn than in summer, is consistent with the results of water quality and relative contribution. Redundancy analysis (RDA) indicated that the environmental variables OSM had a strong correlation with CDOM absorption, followed by heavy metal, e.g., Mn, Hg and Cr⁶⁺. However, for the specific UV absorbance (SUVA₂₅₄), the seasonal values showed opposite results compared with the reported literature. The potential reasons were the more UDOM (uncolored Dissolved Organic Matter) from human source (wastewater effluent) existed in waters. Terrigenous inputs simultaneously are in relation to the a_CDOM(440)-DOC relationship with the correlation coefficient was 0.90 in summer (2-tailed, p<0.01), and 0.58 in autumn (2-tailed, p<0.05). Spatial distribution of CDOM parameters exhibited that the downstream regions focused on dry land have high CDOM molecular weight and aromatic hydrocarbon. Partial sampling locations around the cities or countries generally showed abnormal values due to terrigenous inputs. As a bio-optical model parameter, spectral characteristic of CDOM is helpful in adjusting the derived algorithms in highly-polluted environments. The study on organic carbon and pollutants in highly-polluted waters had an important contribution to global carbon balance estimation and water environment protection.

The long-term use of fertilizers and pesticides in conventional cultivation has resulted in a decrease in soil productivity and vegetable yields in greenhouses. However, only a limited number of studies have explored the impacts of organic cultivation on greenhouse soil. Specifically, there is a scarcity of research examining the alterations in soil aggregate mediated organic carbon and microbial communities, which are known to enhance soil productivity. This study investigated the properties of soil aggregates, including the levels of organic carbon fractions, microbial community, and enzyme activity with the three aggregate classes microaggregates (&lt;0.25 mm), small macroaggregates (2-0.25 mm) and large macroaggregates (&gt;2 mm). These investigations were conducted under three different cultivation methods in a greenhouse: conventional cultivation (CC), integrated cultivation (IC), and organic cultivation (OC) in greenhouse. The results showed that (1) OC and IC promoted the formation of small macro-aggregates and enhanced aggregate stability compared to CC, (2) SOC in the three size fractions of OC increased by 98.99%-92.06% compared to CC; EOC increased by 98.47%-117.59%; POC increased by 138.59%-208.70%; MBC increased by 104.71%-230.61%; DOC increased by 21.93%-40.90%, respectively; (3) Organic cultivation significantly increased enzyme activity in all three particle size aggregates and increased the relative abundance of bacteria in micro-aggregates as well as the relative abundance of fungi in small macro-aggregates. Structural equation model (SEM) analysis revealed that organic farming practices fostered the development of smaller macro-aggregates, elevated microbial and enzyme activities within soil aggregates, and facilitated the conversion of soil nutrients and carbon sequestration. consequently, this led to an increase in soil organic carbon content and improved vegetable yield in greenhouse environments. In conclusion, the soil carbon content and vegetable yield are enhanced through long-term organic cultivation in greenhouses, primarily by increasing the proportion of small macro-aggregates.

Nowadays, animal breeders look for effective innovations to care animal health. Use of probiotics, postbiotics, parabiotics and the other beneficial natural substances are dominated. Mundticin-like substance EM 41/3 is thermo-stable bacteriocin (postbiotic) with a broad antimicrobial spectrum. In this study its effect in broiler rabbits was assessed. Rabbits represent food-derived animal and they are also suitable animal model. The parameters tested were analyzed by validated methods. Administration of MLS EM 41/3 produced by non-autochthonous strain Enterococcus mundtii EM 41/3 lead to significant increase of parameter immunity-phagocytic activity, while it did not influence microbiota composition. It also did not influence blood biochemistry and no oxidative stress was noted. Moreover, higher growth parameters were noted and also stimulated hydrolytic activity. Finally, no negative influence on rabbit meat quality was noted. Postbiotic MLS EM 41/3 administration in feeding strategy seems to be contributing fact for rabbit health status maintaining.

PEDOT:PSS (polyethylene dioxythiophene:polystyrenesulfonate) is a commonly used hole injec-tion layer (HIL) in optoelectronic devices due to its high conductive properties and work function. However, the acidic and hygroscopic nature of PEDOT:PSS can be problematic for device stability over time. To address this issue, in this study, we have demonstrated the potential of an organic-inorganic hybrid HIL, by incorporating solution-processed WOx nanoparticles (WOx NPs) into the PEDOT:PSS mixture. This hybrid solution was found to have a superior hole transport ability and low Ohmic contact resistance, contributing to higher brightness (~62 000 cd m-2) and current efficiency (13.1 cd A-1) in the manufactured quantum-dot based light-emitting diodes (QLEDs). In addition, the resulting devices achieved a relative operational lifetime of 7,071 hours, or approxi-mately twice that of traditional QLEDs with PEDOT:PSS HILs. The proposed method is an un-complicated, reliable and low-cost way to achieve long operational lifetimes without sacrificing efficiency in optoelectronic devices.

Biomass materials have received attention for energy storagebecaused of the advantage of low-cost, easy-to-prepare, and eco-friendliness. Three-dimensional carbon materialswith abundant pore structure gradually becomeresearch hotspot in high-performance energy storage. In this study, an easy-to-prepare, green, light and elastic activated carbon was present using the biomass Juncus effusus (JCE) via high-temperature pyrolysis, followed by activation in air. Compared with previously reported bio-carbons, the proposed air-activated bio-carbon contributes in the fabrication of pores to preserve the interconnected, reticular and tubular structure. Moreover, the interconnected porous material also inherits the excellent tenacity of the original JCE such as the material can be bended to below 90^o under an external force while maintaining structural integrity. The activated porous carbon material exhibits an enhanced electric double-layer capacitance (~210 F g^-1 at 1 A g^-1), with capacitance retention of ~78.62% at 10 A g^-1. The interconnected porous carbon microtubes electrode as a double-layer symmetric capacitor exhibits considerable capacitance retention (84%) after 2000 cycles at 1 A g^-1. The improved energy storage performance was proposed to be attributed to the shortened ionic diffusion distance and sufficient contact between the interface of the carbon electrode and electrolyte, which is resulted from the elastic, undamaged structure and types of pores. These results demonstrated that as-preparedcarbon materials have potentional application in symmetric capacitors.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

Raman spectra of [TeX6](Y2) (X, Y - Cl, Br, I) were recorded in the temperature range 5-300 K. The vibration frequency of molecular halogens as function on temperature and the type of halogen X- in the [TeX6]2- complex was obtained. The vibration frequency of the molecular halogen Y2 depends on the type of halogen X- complex [TeX6]2- The temperature dependence of the Y2 frequency is anomalous compared to what was expected for a conventional anharmonic oscillator. It is shown that the interpretation of the experimental results based on the concept of traditional chemical bonding is quite satisfactory in all cases. The study was motivated by the need to consider the mechanism of interaction in the X-Y2 contacts.

Taiwan developing offshore wind power to promote green energy and self-electricity production. In this study, a Light Detection and Ranging (Lidar) was set up at Chang-Hua development zone one on the sea and 10km away from the seashore. At Lidar location, WRF (3.33km & 2km grid lengths) model and WAsP were used to simulate the wind speed at various elevations. Three days mean wind speed of simulated results were compared with Lidar data. From the four wind data sets, developed five different comparisons to find an error% and R-Squared values. Comparison between WAsP and Floating Lidar was shown good consistency. Lukang meteorological station 10 years wind observations at 5m height were used for wind farm energy predictions. The yearly variation of energy predictions of traditional and TGC wind farm layouts are compared under purely neutral and stable condition. The one-year cycle average surface heat flux over the Taiwan Strait is negative (-72.5 (W/m2) and 157.13 STD), which represents stable condition. At stable condition TGC (92.39%) and 600(92.44%), wind farms were shown higher efficiency. The Fuhai met mast wind data was used to estimate roughness length and power law exponent. The average roughness lengths are very small and unstable atmosphere.

Byers Peninsula is considered one of the largest ice-free areas in Maritime Antarctica. Since 2006, the Spanish Polar Program has taken part in a large number of environmental studies involving effects of climate changes in lives cycles, limnology and microbiology. Soils from maritime Antarctica are generally weakly developed and have chemical, physical and morphological characteristics strongly influenced by the parent material. However, biological activity during the short Antarctic summer promotes intense transference of nutrients and organic matter in areas occupied by different species of birds and marine mammals. To mapping and monitoring those areas with high biological occupation, could be very useful to have models of edaphic properties prepared from satellite images. In this approach, Deep Learning and Linear Regression models of soil properties and spectral indexes as explicative variables were performed. We training models of soil properties closely related to biological activity such as Dissolved Organic Carbon (DOC) and the iron fraction associated with organic matter (Fe). We tested the best approach to model the spatial distribution of DOC, Fe and pH by training models of Linear Regression and Deep Learning over Sentinel2 and WorldView2 images. The most robust models were used to track possible areas with ornithogenic soils as well as areas of the Byers Peninsula that could support the highest biological development.

Candidiasis is considered an emerging public health concern because of the occurrence of drug-resistant Candida strains and the lack of available structurally diverse antifungal drug armamentariums. The indole alkaloid globospiramine from the anticandidal Philippine medicinal plant Voacanga globosa exhibits a variety of biological activities; however, its antifungal properties remain to be explored. In this study, we report the in vitro antifungal activities of globospiramine against Candida albicans and Candida tropicalis and explore its possible target proteins using in silico methods. The colony-forming unit (CFU) viability assay revealed time- and concentration-dependent anticandidal effects of the alkaloid by decreasing almost 50% of the viable CFUs 60 min after treatment. Results of the MIC and MFC assays indicated inhibitory and fungicidal effects of globospiramine against C. albicans (MIC = 8 µg/mL; MFC = 4 µg/mL) and potential fungistatic effects against C. tropicalis at lower concentrations (MIC = 4 µg/mL; MFC &gt; 64 µg/mL). The FAM-FLICA poly-caspase assay showed metacaspase activation in C. albicans cells at concentrations of 16 and 8 µg/mL, which agreed with the MIC and MFC values. Molecular docking and molecular dynamics simulation experiments indicated stable, strong binding of globospiramine with the target proteins 1,3-β-glucan synthase and Als3 adhesin enzymes, which are indirectly involved in apoptotic-driven candidal inhibition.

Levels of trace element pollution in surface soil can be estimated using soil analyses and leaching tests. These methods may reveal different results due to the effect of soil properties, such as grain size and mineral composition, on elemental availability. Therefore, this study advocates an alternative method for monitoring and assessment of trace element pollution in surface soil using terricolous fruticose lichens. Lichens growing at abandoned mine sites and unpolluted areas in southwest Japan and their substrata were analyzed using inductively coupled plasma-mass spectrometry and X-ray fluorescence spectrometry to clarify the relationships between Cu, Zn, As, and Pb concentrations in lichens and soils, including their absorption properties. Concentrations of these elements in the lichens were positively correlated with those in the soils regardless of lichen species, location, habitat, or conditions of soils. The analyzed lichens had neither competitive nor antagonistic properties in their elemental absorption, which made them good biomonitors of trace element pollution in surface soil. The distribution maps of average Cu, Zn, As, and Pb concentrations at each sampling region detected almost all of the Cu, Zn, and As pollution of the soils. Therefore, lichens could be used in practical applications to monitor Cu, Zn, and As pollution in surface soils.

Considerable efforts have been made in recent years to identify an optimal treatment method for the removal of antibiotics from wastewaters. A series of supramolecular organic-inorganic magnetic composites containing Zn-modified MgAl LDHs and Cu-phthalocyanine as photosensitizer have been prepared with the scope to β-lactam antibiotics removal from aqueous solutions. The characterization of these materials confirmed the anchorage of Cu-phthalocyanine onto the edges of the LDH lamellae, with a negligible part inserted in the interlayer space. The removal of β-lactam antibiotics occurred via a concerted adsorption and photocatalytic degradation. The efficiency of the composites was depending on i) the LDH: magnetic nanoparticle (MP) ratio, that is strongly correlated to the textural properties of the catalysts, and ii) the phthalocyanine loading in the final composite. A maximum of the efficiency was achieved with a removal of ~93% of antibiotics after 2h of reaction.

The eutrophication of open water bodies, especially in coastal water area, has received intensive public focuses in recent years. Biological treatment of organic pollutants in industrial and domestic wastewater requires microbial flora to participate. The environmental impact of these microbes, particularly in regard to the spread of antibiotic resistance genes and pathogenicity in coastal water, remains largely unknown. We initiate studies to examine antibiotic resistance genes (ARGs) in microbial flora and study the mode of antibiotic spread in the coastal waters of Bohai Bay, North China by using high performance liquid chromatography-mass spectrum analysis and quantitative polymerase chain reaction. The metabolic features of bacteria related to the presence of ARGs in the coastal area showed the enrichment of Pseudomonadale species with triple resistance properties (ampicillin, kanamycin and gentamycin) at the estuary site locating adjacent to a coastal sewage treatment plant where both type I and type II polyketide synthase genes and b-lactam type antibiotics are detected. Pseudomonadale order is phylogenetically belonged to Proteobacteria Phylum, Gamma-proteobacteria Class and contains Pseudomonadaceae family and Pseudomonas genus. QPCR analysis suggests that the percent occupation of Pseudomonadale species to total Proteobacteria in the examined stations is close to several sampling stations close to sewage treatment plants, where consistent release of organic wastes occurred.

The objective of this work was to investigate the deacidification of bio-oils (BOs) from triglyceride-based biomass through the application of liquid-liquid extraction (LLE) in a simple stage, using methanol and water as a binary solvent and feed/solvent ratio of 1/1. For this, the effects of process parameters such as the water content present in the solvent, the content of carboxylic acids present in the bio-oil, and the extraction temperature on the deacidification process through the efficiency and distribution coefficient were evaluated, as well as the effects of such parameters on the quality of deacidified bio-oils through physical-chemical analyzes and GC-MS analysis. The results show that such process parameters significantly affect the quality of deacidified bio-oils. The ideal condition to have the highest acid removal, i.e., the highest deacidification efficiency (72.65%), is the one in which the deacidification process is performed with aqueous methanol (5% water) at 35 °C and for BOs that have a total acid number (TAN) equal to 24.38 mg KOH/g. Therefore, the process of deacidification by LLE using aqueous methanol is a promising alternative for removing carboxylic acids and other oxygenated compounds, contributing significantly to the upgrading or improving biofuels produced by catalytic thermal cracking.

The rationalization of single molecule magnets’ (SMMs) magnetic properties by quantum mechanical approaches represents a major task in the field of the Molecular Magnetism. The fundamental interpretative key of molecular magnetism is the phenomenological Spin Hamiltonian and the understanding of the role of its different terms by electronic structure calculations is expected to steer the rational design of new and more performing SMMs. This paper deals with the ab initio calculation of isotropic and anisotropic exchange contributions in the Fe(III) dimer [Fe₂(OCH₃)₂(dbm)₄]. This system represents the building block of one of the most studied Single Molecule Magnets ([Fe₄RC(CH₂O)₃)₂(dpm)₆] where R can be an aliphatic chain or a phenyl group just to name the most common functionalization groups) and its relatively reduced size allows the use of a high computational level of theory. Calculations were performed using CASSCF and NEVPT2 approaches on the X-ray geometry as assessment of the computational protocol, which has then be used to evinced the importance of the outer coordination shell nature through organic ligand modelization. Magneto-structural correlations as function of internal degrees of freedom for isotropic and anisotropic exchange contributions are also presented, outlining for the first time the extremely rapidly changing nature of the anisotropic exchange coupling.

How hands-on gardening impacts behaviors including healthy eating and physical activity during early childhood can be of critical importance for preventing early onsets of obesity. This research investigates how participating in hands-on gardening impacts preschoolers’ (3-5 years old) physical activity (measured by accelerometers) in childcare centers in the Semi-Arid Climate Zone. The research was conducted in eight licensed childcare centers located in West Texas with 149 children (n=149). Four childcare centers in the experimental group received hands-on garden interventions; the other four in the control group did not. In both experimental (intervention) and control (non-intervention) centers, children wore Actigraph GT3X+ accelerometers continuously for 5 days before and for 5 days after intervention (a total of 10 days). Results show that the duration of sedentary behavior of children in the experimental (intervention) group significantly decreased compared to children in the control (non-intervention) group. The finding suggests that the positive effects of childcare hands-on gardening on physical activity extend to semi-arid climate zones where gardening is challenging due to high temperatures and lack of annual rainfall. The research emphasizes the critical need to incorporate hands-on gardening in childcare centers as an obesity prevention strategy nationally in the U.S. and beyond.

Background: The validation of laser usage during laparoscopic procedures, notably by Camran Nezhat in the late 1980s, has been significant. Lasers offer precision and depth control in tissue vaporization without bleeding. Surgical intervention remains central in managing endometrio-sis-associated pain and infertility, especially for patients unresponsive to hormonal therapy. Methods: This retrospective cohort study included 200 patients with SPE who underwent laparo-scopic laser vaporization. Surgery was performed using a CO2 laser, and histological confirma-tion of endometriosis was obtained for all cases. Pain scores and SF-36 questionnaire domains were assessed preoperatively and postoperatively. Fertility outcomes were evaluated among pa-tients desiring pregnancy. Results: Significant improvements in pain score and SF-36 questionnaire domains were ob-served postoperatively (p-value

Two novel inorganic–organic hybrid supramolecular assemblies, namely, (4-HNA)(18-crown-6)(HSO₄) (1) and (4-HNA)₂(18-crown-6)₂(PF₆)₂(CH₃OH) (2) (4-HNA = 4-nitroanilinium), were synthesized and characterized by infrared spectroscopy, single X-ray diffraction, differential scanning calorimetry (DSC), and temperature-dependent dielectric measurements. The two compounds underwent reversible phase transitions at about 255 K and 265 K, respectively. These phase transitions were revealed and confirmed by the thermal anomalies in DSC measurements and abrupt dielectric anomalies during heating. The phase transition may have originated from the [(4-HNA)(18-crown-6)]⁺ supramolecular cation. The inorganic anions tuned the crystal packings and thus influenced the phase-transition points and types. The variable-temperature X-ray diffraction data for crystal 1 revealed the occurrence of a phase transition in the high-temperature phase with the space group of P2₁/c and in the low-temperature phase with the space group of P2₁/n. Crystal 2 exhibited the same space group P2₁/c at different temperatures. The results indicated that crystals 1 and 2 both underwent an iso-structural phase transition.