This paper describes different variants of broadband and simple attenuator modules for beamforming applications, based on Radio Frequency Micro Electro-Mechanical Systems (RF-MEMS), framed within Coplanar Waveguide (CPW) structures. The modules proposed in the first part of this work differ in their actuation voltage, topology, and desired attenuation level. Fabricated samples of basic 1-bit attenuation modules, characterized by a moderate footprint of 690 x 1960 µm2 and aiming at attenuation levels of -2, -3 and -5 dB in the 24.25-27.5 GHz range, are presented in their variants featuring both low actuation voltages (5-7 V) as well as higher values (~ 45V), the latter ones ensuring larger mechanical restoring force (and robustness against stiction). Beyond the fabrication non-idealities that affected the described samples, the substantial agreement between simulations and measurement outcomes proved that the proposed designs could provide precise attenuation levels up to 40 GHz, ranging up to nearly -3 dB and -5 dB for the series and shunt variants, respectively. Moreover, they could be effective building blocks for future wideband and reconfigurable RF-MEMS attenuators. In fact, in the second part of this work, combinations of the discussed cells and other configurations meant for larger attenuation levels will be investigated.

Education is expected to support the development of a more sustainable way of thinking, working, and living. Although there is a broad range of literature on Education for Sustainable development (ESD), the role of principals in the implementation of sustainability and ESD in schools has rarely been taken into consideration. However, based on the results of school effectiveness research, one can assume that school principals exert a significant influence on ESD. Sustainability is a leadership issue. When a school aims at integrating sustainability and ESD, the principal plays a pivotal role. She or he has to support the endeavor wholeheartedly and credibly, organize a participative process of school development, push ahead sustainability and ESD in the daily life of the school, support teaching staff in the application of ESD, involve students and offer them opportunities to launch their own initiatives. This article seeks to support principals in leading their schools towards sustainability. Four stages of the integration of Sustainability and ESD in a school are defined. For each of these stages, a number of actions and management strategies are suggested and explained in detail.

Polycyclic aromatic hydrocarbons (PAHs) have emerged as promising materials for organic electronics, including organic photovoltaics (OPVs), organic field-effect transistors (OFETs), and organic light-emitting diodes (OLEDs). Particularly, non-hexagonal ring-fused PAHs are highly desirable due to their unique optoelectronic properties. Herein, a new redox-active azulene-perylene diimide triad 1 and its ring-fused counterpart, diazulenocoronene diimide 2, were synthesized and fully characterized by a combination of NMR, cyclic voltammetry, spectroelectrochemistry, and UV-visible absorption spectroscopy. Density functional theory (DFT) and time-dependent DFT (TD-DFT) calculations were performed to gain further insight into various electronic transitions. Interestingly, we found that the adaptive response to acids and bases manifests itself in a reversible two-color-change that can be attributed to changes in the chemical structures.

Appropriate techniques for promoting reading fluency are difficult to implement in the classroom. There is little time to provide students with individualized feedback on reading aloud or to moti-vate them to do so. In this context, VR can be beneficial for learning, to provide individualized feedback and for increasing learners' engagement. Studies analyzing established methods of lan-guage learning in school in VR seem to be lacking so far. Therefore, this study project was the first to analyze the acceptance of students towards the implementation of a concept of reading fluency training with students at a secondary school in VR. The study method was developed based on the Technology Acceptance Model. The VR environment developed is web-based and provides indi-vidual and collaborative opportunities for training reading fluency, giving, and receiving feed-back, and deepening content understanding of the reading texts. To analyze the acceptance of the VR environment, 5 guided interviews were conducted. The results show that despite technical challenges with the VR environment, students accepted and appreciated the reading fluency training in VR. The integration of established concepts of reading fluency training in foreign lan-guage classrooms has great potential as additional added value can be created to address the challenges of face-to-face instruction.

Introduction: This study aimed to validate the psychometric properties of the German eHealth Impact Questionnaire (eHIQ-G), which is divided into two independently administered and scored parts. Methods: 162 people with MS browsed one of two possible websites containing information on MS and completed an online survey. Internal consistency was assessed by Cronbach’s alpha and structural validity by Confirmatory Factor Analysis. Construct validity was examined by assessing correlations with the eHealth Literacy Questionnaire and the General Self-Efficacy Scale. Moreover, the mean difference of the eHIQ-G score between the two websites was investigated. Results: Cronbach’s alpha for the eHIQ-G subscales ranged from .833 to .885. The eHIQ-G part 1 achieved acceptable levels of goodness-of-fit indices, whereas the fit for the eHIQ-G part 2 was poor and likewise for the alternative modified models. The correlations with the reference instruments were 0.08 – 0.62 and as expected. Older age was related with lower eHIQ-G part 1 score, whereas no significant effect was found for education. Although not significant, the website ‘AMSEL’ reached higher mean scores on eHIQ part 2. Conclusion: The eHIQ-G has good internal consistency, and sufficient structural and construct validity. It will facilitate the measurement of the impact of websites providing health information.

This paper presents a hydrodynamic numerical model for a pitching wave energy converter (WEC). The model uses potential wave theory and is based on Cummins' equation, with nonlinear hydrostatic restoring stiffness and excitation forces based on instantaneous body position and water surface elevation. The numerical model can include non-linear forces, like quadratic drag, power-take-off and other forces that may account for unknown viscous effects observed in experiments. The paper discusses the applicability and limitations of the code and presents the cases where assumptions and simplifications can be made. The goal is to conclude on the simplest, yet accurate, version of the model by evaluating its accuracy using experimental data. The case study for validation is Floating Power Plant's (FPP's) WEC [1]. In the full-scale commercial project, FPP's device consists of a semisubmersible platform hosting a wind turbine (5-8MW) and 4 WECs, each one connected to the platform by a rotation shaft. Due to the configuration of the platform, strong interactions occur between the WECs and the structure, as they are very closely spaced. In order to validate a numerical model able to simulate these hydrodynamic interactions, wave basin experiments with a similar but simplified setup were performed.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

Among the various types of gas sensors, the chemoresistive gas sensors based on metal oxides are considered the most attractive ones due to their simple operation, low costs and miniaturization. Thin films of V2O5 undoped and doped with TiO2 were studied as nitrogen dioxide, methane and hydrogen sensors. The experimental kinetics of the electrical conductivity changes due to introduction and removal of gas on metal oxide gas sensors were successfully explained in terms of the Langmuir adsorption theory.

Many fields of human activity benefit from the ability to create images of obscured objects placed behind walls and to map their displacement in a noninvasive way. Usually, imaging devices like Synthetic Aperture Radars (SAR) and Ground Penetrating Radars (GPR) use expensive dedicated electronics which results in prohibitive prices. This paper presents the experimental implementation and the results obtained from an imaging system capable of performing SAR imaging and interferometric displacement mapping of targets located behind walls, as well as 3D GPR imaging using a low-cost general-purpose radar sensor. The proposed solution uses for the RF section of the system a K-band microwave radar sensor module implementing Frequency Modulated Continuous Wave operation. The low-cost sensor was originally intended for simple presence detection and ranging for domestic applications. The proposed system was tested in several scenarios and proved to operate as intended for a fraction of the cost of a commercial imaging device.

This review delves into the growing field of flexible and stretchable strain sensors utilized in human gait analysis, focusing on determining knee bending angle and muscle activities when a human subject walks. Recent advancements have enabled these sensors to accurately capture biomechanical parameters while accommodating the body's natural movements. We examine the principles underlying these sensors' design and fabrication techniques, emphasizing their flexibility, stretchability, and biocompatibility for seamless integration into wearable systems. Through critical evaluation of existing methodologies, we assess the reliability and validity of these sensors in quantifying gait parameters. Furthermore, we discuss this technology's clinical and research implications, highlighting its potential in personalized rehabilitation and sports performance optimization. We provide an overview of flexible strain sensors and their application for analyzing human walking gait, especially for observing walking gait in rehabilitation programs. First, we present the basic working principles of various flexible strain sensors. Second, by the application of flexible strain sensors as walking gait monitoring. Finally, current challenges and future opportunities in this research area are discussed. By synthesizing current knowledge and outlining future directions, this review aims to provide insights for researchers and practitioners seeking to leverage flexible and stretchable strain sensors for comprehensive human gait analysis.

Keywords: mHealth; peritoneal dialysis; functionality; usability

Among magnetoelectric (ME) heterostructures, ME laminates of the type Metglas-like / PVDF (magnetostrictive+piezoelectric constituents) have shown the highest induced ME voltages, usually detected at the magnetoelastic resonance of the magnetostrictive constituent. This ME coupling happens because of the high cross-correlation coupling between magnetostrictive and piezoelectric material, and is usually associated with a promising application scenario for sensors or actuators. In this work we detail the basis of the operation of such devices, as well as some arising questions (as size effects) concerning their best performance. Also, some examples of their use as very sensitive magnetic fields sensors or innovative energy harvesting devices will be presented At the end, the challenges, future perspectives and technical difficulties that will determine the success of ME composites for sensor applications are discussed.

In this work, an innovative numerical approach for polylinear approximation (polylinearization) of non-self-intersecting compact sensor characteristics (transfer functions) specified either pointwise or analytically is introduced. The goal is to optimally partition the sensor characteristic, i.e. to select the vertices of the approximating polyline (approximant) along with their positions on, the sensor characteristics so that the distance (i.e. the separation) between the approximant and the characteristic is rendered below a certain problem-specific tolerance. To achieve this goal, two alternative non-linear optimization problems are solved, whose essential difference is in the adopted quantitative measure of the separation between the transfer function and the approximant. In the first problem, which relates to absolutely integrable sensor characteristics (their energy is not necessarily finite, but they can be represented in terms of convergent Fourier series), the polylinearization is constructed by numerical minimization of the L^1--metric (a distance-based separation measure), concerning the number of polyline vertices and their locations. In the second problem which covers the quadratically integrable sensor characteristics (whose energy is finite, but they do not necessarily admit a representation in terms of convergent Fourier series), the polylinearization is constructed by minimizing numerically the L^2-metric (area-, or energy-based separation measure) for the same set of optimization variables –the locations, and the number of polyline vertices.

Plant leaf area index (LAI) is a key characteristic affecting field canopy microclimate. In addition to traditional professional measuring instruments, smartphone camera sensors have been used to measure plant LAI. However, when smartphone methods were used to measure conifer forest LAI, very different performances were obtained depending on whether the smartphone was held at the zenith angle or at a 57.5° angle. To validate further the potential of smartphone sensors for measuring conifer LAI and to find the limits of this method, this paper reports the results of a comparison of two smartphone methods with an LAI-2000 instrument. It is shown that both methods can be used to reveal the conifer leaf-growing trajectory. However, the method with the phone oriented vertically upwards always produced better consistency in magnitude with LAI-2000. The bias of the LAI between the smartphone method and the LAI-2000 instrument was explained with regard to four aspects that can affect LAI: gap fraction, leaf projection ratio, sensor field of view (FOV), and viewing zenith angle (VZA). It was concluded that large FOV and large VZA cause the 57.5° method to overestimate the gap fraction and hence underestimate conifer LAI, especially when tree height is greater than 2.0 m. For the vertically upward method, the bias caused by the overestimated gap fraction is compensated for by an underestimated leaf projection ratio.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

Contaminants of Emerging Concern (CECs), a new category of contaminants in limelight, is a major issue of global concern. The pervasive nature of CECs and its harmful effects, such as cancer, reproductive disorders, neurotoxicity etc., make the situation alarming. The perilous nature of CECs lies in the fact that even very small concentration of CECs can cause great impacts on living beings. It also has a nature of bioaccumulation. Thus, it is the ultimate need to have efficient sensors for detection of CECs to ensure safe living environment. Electrochemical sensors are an efficient platform for CEC detection as they are highly selective, sensitive, stable, reproducible, and prompt, and can detect very low concentrations of analyte. Major classes of CECs are pharmaceuticals, illicit drugs, personal care products, endocrine disruptors, newly registered pesticides, and disinfection by-products. This review focusses on CECs, including their sources and pathways, health effects caused by them, and electrochemical sensors as reported in literatures under each category for the detection of major CECs.

Structural deformations are one of the most significant factor that affects machine tool (MT) positioning accuracy. These induced errors are complex to be represented by a model, nevertheless they need to be evaluated and predicted in order to increase the machining performance. This paper presents a novel approach to calibrate a machine tool in real-time, analyzing the thermo-mechanical errors through Fibre Bragg Grating (FBG) sensors embedded in the MT frame. The proposed configuration consists of an adaptronic structure of passive materials, Carbon Fibre Reinforced Polymers (CFRP), equipped by FBG sensors that are able to measure in real-time the deformed conditions of the frame. By using a proper thermo-mechanical kinematic model, the displacement of the end effector may be predicted and corrected when it is subjected to external undesired factors. By starting from a set of FE simulations to develop a model able to describe the MT structure stresses, a prototype has been fabricated and tested. The scope was to compare the numerical model with the experimental tests using FBG sensors. The experimental campaign has been performed varying the structure temperature over time and measuring the tool tip point (TTP) positions. The obtained results showed a substantial matching between the real and the predicted position of TTP confirming the effectiveness of the proposed calibration system.

In mining machines with friction discs, but also in multi-rope traction elevators, it is necessary to distribute the applied tensile load, generated by the weight of the cage and counterweight, evenly in all cross-sections of the load-bearing ropes. Hydraulic devices used for this purpose can operate on the principle of Pascal's law. The article presents a structural design, a 3D model and an implemented solution of a laboratory device capable of simulating a practical method of evenly distributing the total weight of the load into partial tensile forces of the same size acting on a selected number of load-bearing ropes. The laboratory equipment uses two pairs of three steel cables of finite length for the simulations. During the experimental measurements, tensile forces derived from the tractive force of the piston rods, pushed into the bodies of the hydraulic cylinders by the pressure of the hydraulic oil supplied through the pipeline under the pistons of the hydraulic cylinders, were detected. The resulting amount of hydraulic oil pressure in the hydraulic circuit influenced by different values of the hydraulic oil pressures in the hydraulic cylinders and by the pressure in the supply pipe was experimentally studied on the laboratory equipment. Simulations were also carried out in order to detect the hydraulic oil pressure in the hydraulic circuit caused by the change in the different magnitudes of the tensile forces in the ropes From the experiments carried out, it follows that with the appropriate choice of hydraulic elements and the design of the hydraulic circuit, the weight of the load, acting as the total pulling force in the ropes, can be evenly distributed (with a deviation of up to 5%) to all cross-sections of the load-bearing ropes. If the exact values of the hydraulic oil volumes under the pistons of all hydraulic cylinders are not known, it is not possible to calculate the pressure values in the hydraulic circuit when the valves of the hydraulic pipes are gradually opened.

Water pollution is the main problem in the current scenario which is being faced by mankind due to the industrial and commercial effects. Industrial effluents contain heavy metals and inorganic ions like nitrates and phosphate ions. These ions are being included in waterways through industrial runoff. When the concentration of these hazardous pollutants increases in aquatic flora and fauna causes severe health problems. So remediation of these toxicants from water reserves is of chief importance. Conventional processes along with modern processes are being used for the treatment of industrial wastes. Photo-degradation is a modern method used for the degradation of inorganic ions due to its environmentally friendly nature and cost-effectiveness. In a recent study Aluminum oxide (Al2O3) nanoparticles were synthesized via a green approach at different pH by using Cymbopogan citratus (lemongrass) plant extract and these nanoparticles were used for the removal of inorganic ions from wastewater. The nanoparticles of different pH showed different % degradation of the inorganic ions in acidic medium removal of inorganic waste was less, in basic media % degradation was more as compared to acidic media but maximum % degradation was observed in neutral media like that average % degradation 91% and 81% was observed for nitrate and phosphate ions. The maximum absorbance occurred at 212nm and Al2O3 nanoparticles showed absorbance from 210nm-217nm. The R2 values of pseudo1st, 2nd, and BMG models were 0.956, 0.837, 0.7007 0.95, 0.896, and 0.756 for the nitrate and phosphate ions. Characterizations of synthesized particles were investigated by using UV-visible spectroscopy and other analytical methods like X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The statistical analyses were done using Simple Linear regression (SLR).

Membrane-based sensors (MePSs) exhibit remarkable precision and sensitivity in detecting pressure changes. MePSs are commonly used to monitor catalytic reactions in solution, generating gas products crucial for signal amplification in bioassays. They also allow catalyst quantification by indirectly measuring the pressure generated by the gaseous products. This is particularly interesting to detect enzymes in biofluids associated with disease onset. To enhance the performance of a MePS, various structural factors influence membrane flexibility and response time, ultimately dictating the device's pressure sensitivity. In this study, we fabricated MePSs using polydimethylsiloxane (PDMS) and investigated how structural modifications affect the Young's modulus (E) and residual stress (σ0) of the membranes. These modifications have a direct impact on the sensors' sensitivity to pressure variations, observed as a function of the volume of the chamber (Σ) or of the mechanical properties of the membrane itself (S). MePSs exhibiting the highest sensitivities were then employed to detect catalyst quantities inducing the dismutation of hydrogen peroxide, producing dioxygen as gaseous product. As a result, catalase enzyme was successfully detected using these optimized MePSs, achieving a remarkable sensitivity of (22.7 ± 1.2) µm/nM and a limit of detection (LoD) of 396 pM.

To provide carbon steel a long corrosion protection effect in NaCl solution with various pH, a pH-controlled intelligent inhibitor based on poly-acrylamide (PAM) and oleate imidazoline (OIM) was synthesized. SEM, FT-IR and TGA results indicating the OIM inhibitor was successfully loaded into PAM hydrogel with a very high content (39.64 wt%). The OIM release behavior from hydrogel structure have two stages, quickly release and sustained release. The pH of solution could affect the initial release kinetics of OIM inhibitor and the diffusion path in hydrogel structure. Weight loss measurement of L80 steel in different pH solution with OIM@PAM proved the inhibitor responsive release mechanism and an-ti-corrosion performance. The inhibition efficiency of OIM@PAM can maintain over 80% after long term immersion in harsh corrosive environment (pH 3), which is much higher than the inhibition efficiency of inhibitor in moderate corrosive solution.

This paper comprehensively reviews sensors and sensing devices developed or/and proposed so far utilizing two smart materials: electrorheological fluids (ERFs) and magnetorheological materials (MRMs) whose rheological characteristics such as stiffness and damping can be controlled by external stimuli, an electrical voltage for ERFs and a magnetic field for MRMs, respectively. In this review article, the MRMs are classified into magnetorheological fluid (MRF), magnetorheological elastomer (MRE) and magnetorheological plastomer (MRP). To easily understand the history of sensing research using the two smart materials, the order of this review article is organized in a chronological manner of ERF sensors, MRF sensors, MRE sensors and MRP sensors. Among many sensors fabricated from each smart material, one or two sensors or sensing devices are adopted to discuss on the sensing configuration, working principle and specifications such as accuracy and sensitivity. Some sensors adopted in this article include force sensor, tactile device, strain sensor, wearable bending sensor, magnetometer, display device and flux measurement sensor. After briefly describing what have been reviewed in a conclusion, several challenging future works, which should be done for practical applications as sensors or sensing devices, are remarked in terms of new technologies such as artificial intelligence neural network in which several parameters affecting the sensor signals can be precisely tuned or controlled. It is sure that this review article is very helpful to make creative sensors using not only the proposed smart materials but also several different types of smart materials including shape memory alloys and active polymers.

Sensors and actuators are fundamental units in Cyber-Physical and Internet of Things systems. Because they are included in a variety of systems, using many technologies, it is very useful to characterize their functions abstractly by describing them as Abstract Entity Patterns (AEPs), that are patterns that describe abstract conceptual entities. For concreteness, we study them here in the context of autonomous cars. An autonomous car is a complex system because, in ad-dition to its own complex design, it interacts with other vehicles and with the surrounding in-frastructure. To handle these functions, it must incorporate various technologies from different sources. An autonomous car is an example of a Cyber-Physical System, where some of its func-tions are performed by Internet of Things units. Sensors are extensively used in autonomous cars to measure physical quantities; actuators are commanded by controllers to perform appro-priate physical actions. From AEPs we can derive concrete patterns, a structure combining re-lated AEPs is an Entity Solution Frame (ESF). Both sensors and actuators are susceptible to mali-cious attacks due to the large attack surface of the system where they are used. Our work is in-tended to make autonomous cars more secure, which also increases their safety. Our final objec-tive is to build a Security Solution Frame for sensors and actuators of autonomous cars that will facilitate their secure design. A Security Solution Frame is a solution structure that groups to-gether and organizes related security patterns. This article is the first stage of a secure unit that can be used to design not only secure autonomous cars but also any system where sensors and actuators are used. This paper concentrates on AEPs and ESFs for sensors and actuators; that is, on the functional aspects of these devices.

Magnetic sensors are widely used in health management systems for turbomachinery, but their applications in the hot zone are limited due to the loss of magnetic properties by permanent magnets with increasing temperature. The paper presents and verifies models and design solutions aimed at improving the performance of an inductive sensor for measuring the motion of rotating objects operating at elevated temperatures (200-1000C), such as compressor and turbine blades. Physical, analog and mathematical models of the interaction of blades with the sensor were developed. A prototype of the sensor was made and its tests were carried out on the RK-4 rotor rig for the speed of 7000 rpm, in which the temperature of the sensor head was gradually increased to 1100C. The sensor signal level was compared to that of an identical sensor operating at room temperature. The heated sensor works continuously producing the output signal whose level does not change significantly. What is more, a set of six probes passed an initial engine test in an SO-3 turbojet. It was confirmed that the proposed design of the inductive sensor is suitable for blade health monitoring of the last stages of compressors, steam turbines as well as previous generation gas turbines operating below 1000C, even without a dedicated cooling system. In real-engine applications, sensor performance will depend on how the sensor is installed and the available heat dissipation capability

Plasmonic sensors exploiting the Localized Surface Plasmon Resonance (LSPR) of noble metal nanoparticles are common in the visual spectrum. However, for bio-sensors the near infra-red (NIR) windows (600 nm – 900 nm and 1000 nm -1400 nm) are of interest, as it is a region where the absorption coefficient of water, melaninm deoxy- and hemoglobin are all low. The first part of this paper reviews the work that has been undertaken on using gold (Au) and silver (Ag) particles in Metal Enhanced Fluorescence (MEF) in the NIR. Despite this success there are limitations, as there is only a narrow band in the visual and NIR where losses are low for traditional plasmonic materials. Further, noble metals are not compatible with standard silicon manufacturing processes, making it challenging to produce on-chip integrated plasmonic sensors with Au or Ag. Therefore, it is desirable to use different materials for plasmonic chemical and biological sensing, that are foundry-compatible with silicon (Si) and germanium (Ge). One material that has received significant attention is highly doped Ge which starts to exhibit metallic properties at a wavelength as short as 6 μm. This is discussed in the second part of the paper and the results of recent analysis are included.

Adenine nucleotide (AN) 2^nd messengers such as 3’,5’-cyclic adenosine monophosphate (cAMP) are central elements of intracellular signaling, but many details of underlying processes remain still elusive. Like all nucleotides, cyclic nucleotide monophosphates (cNMPs) are net-negatively charged at physiologic pH which limits their applicability in cell-based settings. Thus, many cellular assays rely on sophisticated techniques like microinjection or electroporation. This setup is not feasible for medium- to high-throughput formats, and the mechanic stress that cells are exposed to raises the probability of interfering artefacts or false-positives. Here, we present a short and flexible chemical route yielding membrane-permeable, bio-reversibly masked cNMPs for which we employed the octanoyloxybenzyl (OB) group. We further show hydrolysis studies on chemical stability and enzymatic activation, and present results of real-time assays, where we used cAMP and Ca²⁺ live cell imaging to demonstrate high permeability and prompt intracellular conversion of some selected masked cNMPs. Consequently, our novel OB-masked cNMPs constitute valuable precursor-tools for non-invasive studies on intracellular signaling.

The regulation of intracellular pH in yeast (Saccharomyces cerevisiae) cells is critical for cell function and viability. In yeast, protons (H+) can be excreted from cell by the plasma membrane ATPase Pma1 and pumped into vacuoles by the vacuolar H+-ATPase. Because Pma1 is critical to the survival of yeast cells, it is unknown whether other compensatory components are involved in the pH homeostasis in the absence of Pma1. To elucidate how intracellular pH is regulated independently of Pma1, we employed a screening approach by exposing the yeast haploid deletion mutant library (ver 4.0) to the selective plant plasma membrane H+-ATPase inhibitor PS-1, which we previously reported. After repeated screenings and verification, we identified two proteins, ALY1 and ALY2, that play a role in the regulation of intracellular pH when Pma1 is deficient. Our research uncovers a new perspective on the regulation of intracellular pH related to Pma1 and also preliminarily reveals a role for ALY1 and ALY2 in the regulation of intracellular pH.

We hypothesized possibility that inline registered reticulorumen pH can be as biomarker of cows reproduction and health status. Aim of this study was to evaluate the relationship of reticulorumen pH with biomarkers from automatic milking system (AMS) and some blood parameters and determinate reticulorumen pH as biomarker of cows reproduction and health status. According to cows reproductive status the cows were classified as belonging to the following four groups: 15-30 d. postpartum; 1-34 d. after insemination; 35 d. after insemination (non-pregnant); 35 d. after insemination (pregnant). According reticulorumen pH assay experimental animals were divided into four classes: 1) pH<6.22 (5.3% of cows), 2) pH - 6.22-6.42 (42.1% of cows), 3) pH - 6.42-6.62 (21.1% of cows), 4) pH >6.62 (10.5% of cows). Rumination time, body weight, milk yield, milk fat – protein ratio, milk lactose, milk somatic cell count (SCC), milk electrical conductivity of all quarters of udder were registered with the help of Lely Astronaut® A3 milking robots. The pH, temperature of the contents of cow reticulorumens and cow activity were measured using specific smaX-tec boluses. Blood gas parameters were analyzed using a blood gas analyzer (EPOC, Canada). We found that pregnant cows has higher reticulorumen pH during insemination time, comparing with non-pregnant. Cows with lower reticulorumen pH has lowest milk fat – protein ratio, and lactose concentration, and highest SCC. Cows with lowest reticulorumen pH has lowest blood pH. With increase reticulorumen pH, increases blood potasium and hematocrit, decreases CO2, saturation and sodium.

The world is facing a great technological transformation towards full autonomous vehicles, where optimists predict that by 2030, autonomous vehicles will be sufficiently reliable, affordable and common to displace most human driving. To cope with these trends, reliable perception systems must enable vehicles to hear and see all the surroundings, being light detection and ranging (LiDAR) sensors a key instrument for recreating a 3D visualization of the world in real time. However, perception systems must rely in accurate measurements of the environment. Thus, sensors must be calibrated and benchmarked before being placed on the market or assembled in a car. This article presents an Evaluation and Testing Platform for Automotive LiDAR sensors with the main goal of testing not only commercially available sensors, but also sensor prototypes currently under development in Bosch Automotive Electronics division. The testing system can benchmark any LiDAR sensor under different conditions, recreating the expected driving environment to which such devices are normally subjected. To characterize and validate the sensor under test, the platform evaluates several parameters such as the field of view (FoV), angular resolution, sensor’s range, etc. This project results from a partnership between the University of Minho and Bosch Car Multimedia Portugal, S.A.

This paper present a platform for airborne sensor applications using low-cost, open-source components carried by an easy-to-fly unmanned aircraft vehicle (UAV). The system, available in open-source [1], is designed for researchers, students and makers for a broad range of their exploration and data-collection needs. The main contribution is the extensible architecture for modularized airborne sensor deployment and real-time data visualisation. Our open-source Android application provides data collection, flight path definition and map tools. Total cost of the system is below 800 dollars. The flexibility of the system are illustrated by mapping the location of Bluetooth beacons (iBeacons) on a ground field and by measuring water temperatures in a lake.

In recent years, cancer therapy has witnessed significant advancements, with a focus on personalized and targeted treatment strategies. One promising approach involves the use of stimuli-responsive biomaterials for site-specific drug release. Among these biomaterials, pH, and redox-triggered polymer-nano composites have gained immense attention due to their ability to respond to the specific tumor microenvironment, enhancing therapeutic efficacy while reducing off-target effects. Cancer cells often exhibit anomalous biochemical properties, attributed to lower cytosolic pH (acidic) and elevated redox potential through the epitomized upregulation of undesired genes. Such biological process substantially imbalance the level ions (protons) and biological thiols glutathione (GHS) in the cytoplasm as well as in the subcellular organelles. Superfluous accumulation of ions and redox imbalance is associated with proliferation, invasion, and growth of tumor. Because of high surface area, deep tissue penetration capability, higher hydrophilicity, hydrophobic interior for drug/gene efficient loading, biocompatibility and site-specific targeting efficiency, functionalized polymer nanocomposites are superior to conventional small molecular materials. Paradoxically conventional methods of drug delivery aided therapeutics accompanied with inherent drug/genes are encapsulated in biocompatible carrier or suitable transfecting agents generally suffered with low bioavailability, uncontrolled drug release, low cellular penetration, cellular internalization, toxicity, and poor drug loading efficiency. To overcome these issues, recently various multifunctional nanomaterials were developed, based on synergistic stimuli responsive aided drug release in a specified cellular or subcellular system. High therapeutic efficacy, of nanoparticles (NPs) mainly associated with surface functionalization through biocompatible polymeric materials, site-specific targeting units accompanied with stimuli responsive components. Followed by therapeutically important drug or genetic materials were loaded into NPs either in covalent or non-covalent approach. Intriguingly, combined pH and redox dual stimuli based functional materials specially based on polymeric nanocomposites for cancer therapeutics scarcely reported. This article provides the recent progress in pH and redox-responsive polymer-nano composites for site-specific drug delivery in cancer therapy. It explores design principles, fabrication methods, mechanism of action, and prospects of these dual-stimuli responsive biomaterials.

The aim of this study was to evaluate the emulsification properties of garlic water-soluble compounds (GWSC) after heat treatment (10 min at 95 °C) or pH adjustments (2.5, 3.5 and 7.8). After the various treatments, the extracts were used as such or filtrated (0.45 µm) and 10% soybean oil-in-water emulsions were prepared using low (0.48%) or high (6.55% wt/wt) extract concentrations. Whereas at low GWSC concentration, both heating or acidifying resulted in the formation of bigger oil droplet sizes (i.e. from d32=0.36 µm using unmodified extract, to d32=7–22 µm µm at pH 2.5 with or without extract filtration), the effects were opposite at the highest GWSC concentration. In the latter, heat treatment clearly reduced the droplet size as observed from the micrographs as well as the degree of creaming, though the occurrence of depletion and/or bridging flocculation was still strong. The acidification of the extract at this high GWSC concentration, significantly reduced the droplet size as observed from the micrographs but a strong flocculation was observed. Removal of protein aggregates, and possibly also saponin micelles from the extract, resulted in an obvious increase in emulsion droplet size. This research brings valuable insights on the study and utilisation of novel natural food emulsifiers from plant sources.

Since the systematic evolution of ligands by exponential enrichment (SELEX) method was developed, aptamers have made significant contributions as bio-recognition sensors. Microdevice systems allow for low reagent consumption, high-throughput of samples, and disposability. Due to these advantages, there has been an increasing demand to develop microfluidic-based aptasensors for analytical technique applications. This review introduces the principal concepts of aptasensors and then presents some advanced applications of microdevice-based aptasensors on several platforms. Highly sensitive detection techniques such as electrochemical and optical detection have been integrated into lab-on-a-chip devices and researchers have moved towards the goal of establishing point-of-care diagnoses for target analyses.

In urban areas like Chicago, daily life extends above ground level due to prevalence of high-rise buildings where residents and commuters live and work. This study examines the variation in fine particulate matter (PM2.5) concentrations across building stories. PM2.5 levels were measured using PurpleAir sensors, installed between April 8 and May 7, 2023, on floors one, four, six, and nine of an office building in Chicago. Additionally, data were collected from a public outdoor PurpleAir sensor on the fourteenth floor of a condominium located 800 meters away. Results show that outdoor PM2.5 concentrations peak at 14 meters height, then decline by 0.11 μg/m3 per meter elevation, especially noticeable from midnight to 8 AM under stable atmospheric conditions. Indoor PM2.5 concentrations increase steadily by 0.02 μg/m3 per meter elevation, particularly during peak work hours, likely caused by greater infiltration rates at higher floors. Both outdoor and indoor concentrations peak around noon. We find that indoor and outdoor PM2.5 are positively correlated, with indoor levels consistently remaining lower than outside levels. These findings align with previous research suggesting decreasing outdoor air pollution concentrations with increasing height. The study informs decision-making by community members and policymakers regarding air pollution exposure in urban settings.

Developing novel wound dressings containing medicinal plant extracts can have several potential benefits, including improving the therapeutic value of the dressings and reducing the cost of producing wound dressings. In this study, we prepared foam dressing containing Eclipta prostrata leaf extract and gelatin (Eclipta prostrata dressing). Chemical composition was verified using Fourier transform infrared spectroscopy (FTIR), and pore structure was obtained by scanning electron microscopy (SEM). The physical properties, including absorption and dehydration properties, were also evaluated. The chemical properties were measured to determine the pH environment after being submerged with Eclipta prostrata dressings. The results revealed that the Eclipta prostrata dressing had a pore structure with an appropriate pore size (313.25 ± 76.51 µm and 383.26 ± 64.45 µm for the Eclipta prostrata A and Eclipta prostrata B dressings, respectively). The Eclipta prostrata B dressing was more consistent porosity, resulting in a higher absorption capacity and faster dehydration rate. According to physical properties, the Eclipta prostrata B dressing is best used on low-exuding wounds. Furthermore, the Eclipta prostrata A and B dressings make a slightly acidic environment. Therefore, our foam dressing will not interfere wound healing process.

Applications for Wireless Sensor Networks (WSNs) range from monitoring the environment to automating factories. However, sustained and effective functioning is made more difficult by Sensor Nodes (SNs) limited energy supplies in which optimization is the main issue. So with the aim of increasing the lifespan by decreasing the energy consumption of WSN, Low-Energy Adaptive Clustering Hierarchy (LEACH) protocol with Deep Learning (DL) algorithm is analyzed in this paper. LEACH is a hierarchical mechanism that elects Cluster Heads (CHs) and regularly rotates their positions in order to allocate energy use effectively by using the same amount of energy. However, Deep Learning (DL) method is used to further improve energy optimization. In many applications, the types of Deep Learning methods like Artificial Neural Networks (ANNs) have shown to be very useful. Using this method, WSNs may make more efficient decisions that reduce energy consumption. Data aggregation, duty cycling, and transmission protocols may all be optimized by Deep Learning model's ability to recognize patterns and forecast network behavior. This results in lower energy consumption, a longer lifespan for the network, and better overall performance.

pH value almost affects the function of cells and organisms in all aspects, so in biology, biochemical and many other research fields, it is necessary to apply simple, intuitive, sensitive, stable detection of pH and base characteristics inside and outside the cell. Therefore, many research groups have explored the design and application of pH probes based on surface enhanced Raman scattering（SERS）. In this review article, we discussed the basic theoretical background of explaining the working mechanism of pH SERS sensors, and also briefly described the significance of cell pH measurement, and simply classified and summarized the factors that affected the performance of pH SERS probes. Some applications of pH probes based on surface enhanced Raman scattering (SERS) in intracellular and extracellular pH imaging and the combination of other analytical detection techniques are described. And finally, the development prospect of this field is prospected.

In this work we aim to experimentally study the nucleation and growth of CaCO3 phases precipitated from supersaturated aqueous solutions in the presence of varying concentrations of sulphate oxyanion. The experiments were conducted under pH conditions close to neutral (7.6) and considering a wide range of initial (SO42-)/(CO32-) ratios (0 to ~ 68) in the aqueous solution. We paid special attention to the evolution of the precipitates during ageing within a time framework of 14 days. The mineralogy, morphology and composition of the precipitates were studied by X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy and EDX microanalysis. The concentration of sulphate ions in the reacted aqueous solution was study by ICPs. The experimental results show that the mineral composition of the precipitate recovered in each run varied with the (SO42-)/(CO32-) ratio in the parental solution, which influences the mineral evolution of the precipitates during ageing. We observe that high concentrations of sulphate in the aqueous solution stabilize the vaterite precipitates and inhibit calcite formation. Furthermore, aragonite never precipitates directly form the solution and it is only formed via a dissolution-precipitation process in solutions with high (SO42-)/(CO32-) ratio after long reaction times. Finally, gypsum only precipitates after long ageing in those aqueous solutions with the highest concentration of sulphate. The reaction pathways during ageing, the morphology of the calcite crystals and the composition of vaterite and calcite are discussed considering both, kinetic and thermodynamic factors. These results show a considerably more complex behavior of the system than that observed in experiments conducted under higher pHs and supersaturation levels and lower (SO42-)/(CO32-) ratios in the aqueous phase.

The effect of pH regulation on biohydrogen production was studied using suspended and immobilized mixed cultures. Four sets of experiments were conducted using suspended cells under regulated pH (Sus_R) and non-regulated pH conditions (Sus_N) as well as alginate-immobilized cells under pH regulated (Imm_R) and non-pH regulated conditions (Imm_N). Sus_R showed a peak hydrogen fraction of 44% and complete glucose degradation, compared to Sus_N with a peak hydrogen fraction of 36% and a glucose degradation of 37%. Imm_R experiments showed a peak biohydrogen fraction of 35%, while the peak hydrogen fraction observed with Imm_N was 22%. The highest hydrogen fraction was observed using suspended cells under regulated pH conditions. A 100% glucose degradation was observed in both pH regulated and non-regulated processes using immobilized cells. The rate of pH change was slower for immobilized cells compared to suspended cells suggesting a better buffering capacity under non pH regulated conditions. The study showed that biohydrogen production with suspended cells in a non-regulated pH environment resulted in early termination of the process and lower productivity.

Electrochemical sensors have been used for many decades. Yet, modeling of such sensors used in electrolysis mode is poorly documented, especially in the case parallel action of multiple gases. Those ones are of great interest since they constitute the first brick to bring information on natures and concentrations of a gaseous mixture composition thanks to grey box modeling of sensors array for example. Based on Butler Volmer’s equations, a model assuming parallel reactions at gold cathode has been introduced in this article and confronted to experimental results. Establishment of the model is based on the extraction of 3 variables: the charge transfer coefficient “α”, the reaction order γ, and the reaction constant rate k0. Tests performed without pollutants and with different concentrations of oxygen could be nicely fitted by the model. Then, the influence of polarization current on the 3 variables of the model has been evaluated showing a clear influence on the constant rate and the reaction order. Also, increasing the polarization current enabled us to get selectivity to oxidant gases. Similarly, the effect of the oxygen concentration was evaluated. Results showed that, in this case, the charge transfer coefficients “α” obtained for oxidant gases is quite different that the ones obtained in the polarization current varying conditions. Therefore, the model will be interesting in situations where polarization current and oxygen content are not varied together. Variation of polarization current can be quite interesting to get increased information for multivariate analysis purpose in constant oxygen content situations. Besides, other parameters have are required for applications in which the oxygen content is bound to change like exhaust gases or combustion.

This study investigates novel ferrocene-based electrochemical sensors for metal cation detection through the design, synthesis and characterisation of ferrocene derivatives. Specifically, the re-search determines the redox potentials of ferrocene versus decamethylferrocene to provide in-sight into the redox potential variations between them. The investigation also examines how electrochemical oxidation of the ferrocene moiety can modulate host affinity for transition metals cations via effects such as electrostatic interactions and changes to coordination chemistry. Metal ion coordination to receptors containing functional groups like imine and quinoline is explored to elucidate selectivity mechanisms. These findings advance the fundamental understanding of ferrocene electrochemistry and host-guest interactions, supporting the development of improved cation sensors with optimised recognition properties, sensitivity, and selectivity. Overall, the work lays the necessary groundwork for applications in analytical chemistry and sensor technologies through customised ferrocene-derived materials.

Light-addressable potentiometric sensor (LAPS) is an electrochemical sensor based on the field-effect principle of semiconductor. It is able to sense the change of Nernst potential on the sensor surface, and the measuring area can be controlled by the illumination. Due to the unique light-addressable ability of LAPS, the chemical imaging system constructed with LAPS can realize the two-dimensional image distribution detection of chemical/biomass. In this paper, the advantages of LAPS as sensing unit of microelectrochemical analysis system are summarized. Then, the greatest development of LAPS analysis system is explained and discussed. Especially, this paper focused on the research of ion diffusion, enzymatic reaction, microbial metabolism and droplet microfluidics by using LAPS analysis system. Finally, the development trends and prospects of LAPS analysis system are illustrated.

Current smartphones incorporate different types of sensors that allow us to know our spatial position, they give us information about pressure, speed, acceleration, time, acoustic level, and other different physical magnitudes. These smartphones measure each component of the magnetic field, bearing in mind that any current perpendicular to a magnetic field produces a small potential difference, transversal to the said current, being this voltage easily measurable by Hall sensors. With the implementation of three Hall sensors, and an appropriate app, we can measure the three components of the magnetic field vector, and with this we can obtain information and deduce properties of the physical systems considered. In this paper we are exploring the use of smartphones in a physics laboratory for freshman students. To do this, we have measured, using Hall sensors, the magnetic field created by a linear quadrature, and we have obtained, first of all, its dependence on the distance between the quadrupole and the magnetic sensor. The second purpose of this work is to show that the laboratory is a powerful tool that increases the significant learning of freshman students through advanced technological tools.

Flow sensing in hostile environment is of increasing interest for applications in automotive, aerospace, and chemical and resource industries. Compared to their counterparts, thermal flow sensors are attractive candidates due to the ease of fabrication, lack of moving parts and higher sensitivity. Recently, a number of thermal flow sensor prototypes have been reported in the literature demonstrating the measurement of fluid flows under hostile conditions. This paper summarizes the concept of thermal flow sensing, operational modes and transduction mechanisms. Then, the choice of materials and their corresponding properties are presented in details. The paper also reports recent progress in the development of thermal flow sensors for harsh environment. In addition, the issues and considerations in packaging are reviewed. Finally, we conclude the review with the future prospects.

Hoechst 33342 (H33342) is a fluorescent probe that is commonly used to stain DNA of living cells. To do so, it needs to interact with and permeate through cell membranes. The pH of biological media may vary quite significantly and this influences H33342 ionization state, and may change its rate of permeation through biomembranes. In this work, we address the effect of pH in the association of H33342 with lipid bilayers using a combined experimental and computational approach. The partition of H33342 to 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine (POPC) lipid membranes was experimentally quantified using fluorescence spectroscopy and isothermal titration calorimetry (ITC) measurements. Quantum chemical calculations were performed to select the most stable isomer of H33342 for the overall charges 0, +1, and +2, expected to predominate across the 5 &lt; pH &lt; 10 range. The interaction of these isomers with POPC bilayers was then studied by both unrestrained and umbrella sampling molecular dynamics simulations. While probe insertion occurs for all ionization states, with similar overall equilibrium location, orientation was found to depend on the probe charge, with the neutral form lying mostly parallel and the doubly charged displaying a significant tilt relative to the membrane plane. Both experimental results and computational free energy profiles indicate that the partition coefficient of H33342 displays a small variation over a wide pH range, not exceeding one order of magnitude. The enthalpy of interaction is negative and is larger at lower pH values. This suggests efficient hydrogen bonding between the probe and the lipid, namely for the protonated +2 form. The relatively high lipophilicity obtained for the charged species contrasts with the decrease in their general hydrophobicity as estimated from water and octanol partition. This highlights the distinction between lipophilicity and hydrophobicity, and the importance of considering association with lipid bilayers when predicting the affinity for biomembranes.

Pathologies of the blood brain barrier (BBB) have been linked to a multitude of CNS disorders whose pathology is poorly understood. Cortical spreading depression (CSD) has long been postulated to be involved in the underlying mechanisms of these disease states, yet full understanding remains elusive. This study utilized an in vitro model of the BBB with b.End3 murine endothelial cells to investigate the role of CSD in BBB pathology by characterizing effects of the release of major pronociceptive substances on BBB functional integrity using TEER screening, transcellular uptake, and immunoreactive methods in concert with global proteome and phospho-proteomic approaches. Findings demonstrated relocalization and functional alteration to proteins associated with the cytoskeleton and endothelial tight junctions. Pathologic mechanisms induced by individual substances released during CSD were found to have unique phosphorylation signatures in phospho-proteome analysis, identifying Zona Occludens 1 as a possible pathologic “checkpoint” of the BBB. Utilizing these phosphorylation signatures, possible novel diagnostic methods may be developed for neurological diseases and warrants further investigation.

Due to Motor Neurone Diseases, a large population remains disabled worldwide, negatively impacting their independence and quality of life. This typically involves a weakness in the hand and forearm muscles, making it difficult to perform fine motor tasks such as writing, buttoning a shirt, or gripping objects. This project presents a vision-enabled rehabilitation hand exoskeleton to assist disabled persons in their hand movements. The design goal was to create an accessible tool to help with a simple interface requiring no training. This prototype is built on a commercially available glove where a camera and embedded processor were integrated to help open and close the hand, using air pressure, thus grabbing an object. An accelerometer is also implemented to detect the characteristic hand gesture to release the object when desired. This passive vision-based control differs from active EMG-based designs as it does not require individualized training. Continuing the research will reduce the cost, weight, and power consumption to facilitate mass implementation.

Drones are being used more and more frequently and in various ways to attack people and critical infrastructures, which increases their level of danger and makes early detection and risk assessment even more difficult. There is no ultimate drone sensor. Rather, drones can only be effectively detected, if suitable sensor technologies are integrated within a system. Among the best suited sensorics for this purpose are radar and optical sensors, because the advantage of the radar, given by the long detection range, can be well combined with the additional visual-based information gained from a camera in the mid- and short-range, where usually the radar fails detecting micro drones. In this paper, a modular drone detection and assistance system MODEAS is presented, which can be used to automatically detect and track drones within a range up to some kilometers on the sky, but also in complex urban environments, where buildings and vegetation offer a perfect background for camouflage. The system provides an early detection of flying objects as potential drones, when those are not at all or only as small dots visible for the human eye. Main strengths of the system are the robust AI detection to differentiate such an object against clutter (birds, clouds) and its further classification by model and payload recognition, the latter aspect being considered as an indication of dangerousness. Moreover, once a drone is detected, the system follows it automatically, precisely and smoothly with a high-resolution pan-tilt-camera, measuring the distance to the sensor station with a laser rangefinder, compute the geocoordinates and visualize them live on a map. To improve the precision of the detection, a multisensorial fusion of all sensor detections is performed. Furthermore, alarms may be generated when a drone enters a restricted area.

In recent years, the integration of sensors in agriculture has emerged as a pivotal catalyst for transforming conventional farming practices into precision agriculture. Sensor application is impacting the everyday objects that enhance human life. In this special issue, the main objective was to address recent advantages of sensor application in agriculture covering a wide range of topics in this field. This provides overview of diverse application of sensors in agriculture, highlighting their role in enhancing productivity, sustainability, and resource management. sensors are instrumental in monitoring various agriculture parameter such as soil condition, weather, crop health and livestock wellbeing. By collecting real-time data and providing valuable insight, sensors enable precision farming, optimize resource allocation, and minimize environmental impacts. we have to explore the key sensor types used in agriculture, their applications, benefits, and future prospects, emphasizing their crucial roles in the modernization of agriculture and global quest for food security and crop production.

Sign language recognition is essential in hearing-impaired people’s communication. Sign language recognition is an important concern in computer vision and has been developed with rapid progress in image recognition technology. However, sign language recognition using a general monocular camera has problems with occlusion and recognition accuracy in sign language recognition. In this research, we aim to improve accuracy by using a 2-axis bending sensor as an aid in addition to image recognition. We aim to achieve higher recognition accuracy by acquiring hand keypoint information of sign language actions captured by a monocular RGB camera and adding sensor assist. To improve sign language recognition, we need to propose new AI models. In addition, the amount of dataset is small because it uses the original data set of our laboratory. To learn using sensor data and image data, we used MediaPipe, CNN, and BiLSTM to perform sign language recognition. MediaPipe is a method for estimating the skeleton of the hand and face provided by Google. In addition, CNN is a method that can learn spatial information, and BiLSTM can learn time series data. Combining the CNN and BiLSTM methods yields higher recognition accuracy. We will use these techniques to learn hand skeletal information and sensor data. Additionally, the 2-axis Bending sensor glove data support training AI model. Using these methods, we aim to improve the recognition accuracy of sign language recognition by combining sensor data and hand skeleton data. Our method performed better than using skeletal information, achieving 96.5% accuracy in Top-1.

Novel tetragonal matrix Ba0.5Gd0.5-xNaxF2.5-x, where x = 0.05, doped by Yb3+, Ho3+, Er3+, was synthesized by molten salt synthesis (MSS) from nitrate flux. XRD data show that tetragonal phase with a = 4.122(1) Å, c = 17.672(1) Å is stable in argon atmosphere up to 960 °C. Luminescence spectra recorded in 500-900 nm and 1050-1700 nm upon 974 nm pumping demonstrated the characteristic luminescence at 1550 nm (4I13/2 → 4I15/2) for Er3+ and 1150 nm (5I6 → 5I8) for Ho3+. The relative thermal sensitivity (Sr) at 296-316 K were 0.3 %*K-1 and 5.5%*К-1 in shortwave infrared (SWIR) and visible range, respectively. Synthesized luminophores can be used as dual-range optical temperature sensors, which simultaneously operating in visible and SWIR ranges.

Sensing Technology (ST) plays a key role in Structural Health Monitoring (SHM) systems. ST focuses on developing sensors, sensory systems or smart materials that monitor a wide variety of materials properties aiming to create smart structures and smart materials, using Embedded Sensors (ESs), and allowing continuous and permanent measurements of the structural integrity. The integration of ESs is limited to the processing technology to embed the sensor due to its high-temperature sensitivity and the possibility of damage during its insertion into the structure. In addition, the technological process selection is dependent on the base material composition, either metallic or composite parts. The selection of smart sensors or the technology underlying them is fundamental to the monitoring mode. This paper presents a critical review of the fundaments and applications of sensing technologies for SHM employing ESs, focusing on the actual developments and innovation of these, as well as analysing the challenges that these technologies present, to build a path that allows a connected world through distributed measurement systems.

: This paper presents a couple of meal monitoring systems for senile dementia patients by using electronic weight and temperature sensors. These monitoring systems enable to convey the information of the amount of meal taken by the patients in real-time via wireless communication networks onto the mobile phones of their families or nurses in charge. Thereby, the nurses can easily spot the most desperate patient to take care of while the families can have relief to see the crucial information for survival of their parents at least three times a day. Meanwhile, the senile dementia patients tend to suffer the burn of their tongues because they can hardly recognize the temperature of hot meals served and therefore avoid the burn of tongues. This phenomenon can be discarded by utilizing the meal temperature monitoring system which displays alarm to the patients when the meal temperature is above the reference. These meal monitoring systems can be easily implemented by utilizing low-cost sensor chips and Arduino UNO boards so that elder-care hospitals and nursing homes can afford to exploit them with no additional cost. Hence, we believe that the proposed monitoring systems would be a potential solution to provide a great help and relief not only for the professional nursing nurses working in elder-care hospitals and nursing homes, but also for the families of the dementia patients.

The protection of electronics against environmental influences and mechanical loads is important for integration of conventional electronics in textile conductive tapes. For this purpose, the sensors on the tapes are molded with plastic locally. This process step is recognized in the injection molding process. The molding compound is then later selected depending on: The field of application, the parameters of the manufacturing process and the textile tape properties. We have designed a mould for liquid silicone (LSR) as well as for the textile and electronic insertions. The cavities are sealed by a local compression of the textile and the two inserts are positioned with position pins representing the main aspect of the mould design. The sampling tool and the process parameter optimization are mainly based on the material properties of the silicone and the mechanical sensitivity of the inserts. To reduce the deformation of the circuit boards by the melt front and ensuring the functionality of the electronics a low-pressure process is used.

Diatomite (DME) consists of natural ordered porous structures that are excellent candidates as microcontainers. However, to the best of our knowledge, the application of DME loaded with corrosion inhibitors in anti-corrosion coatings has not hitherto been reported. In this study, DME has been used as a source of microcontainers to load benzotriazole (BTA) inhibitor by an immersion method. In order to prevent unwanted early release of the small molecule BTA inhibitor from the DME microcontainers, inspired by the adhesion characteristics of catechol and amine in mussel adhesion protein, polydopamine (PDA) was coated on their surfaces to generate BTA@DME/PDA microcapsules. Because of the depolymerization characteristics of PDA at low pH, the synthesize microcapsules showed a controllable release function. The SEM morphology, chemical structure, and loading capacity of the synthesized BTA@DME/PDA microcapsules were characterized. The corrosion resistances of epoxy coatings with different contents of BTA@DME/PDA microcapsules were compared by saline immersion and electrochemical impedance tests. A scratched coating with 5wt.% BTA@DME/PDA microcapsules showed the best anti-corrosion effect.

Nisin, an antibacterial compound produced by Lactococcus lactis strains, has been approved by the US Food and Drug Administration to be used as a safe food additive to control the growth of undesirable pathogenic bacteria. Nisin is commonly described as a pH-dependent primary metabolite, since its production depends on growth and culture pH evolution. However, the relationship between bacteriocin synthesis and the consumption of the limiting nutrient has not been described until now. Therefore, this study aimed to develop a competitive four-dimensional Lotka Volterra-like equation to describe the relationships between culture pH, limiting nutrient (total nitrogen: TN) consumption and production of biomass (X) and nisin (BT) in four series of batch fermentation with L. lactis CECT 539 in diluted whey (DW)-based media. The developed four-dimensional LV-like equation (with a unique set of parameters) could not be used to describe all cultures belonging to each fermentation series. However, the four-dimensional LV-like equation described accurately each individual culture, providing a good description of the relationships between pH, TN, X and BT, higher values for R2 and F-ratios, lower values (&lt; 10%) for the mean relative percentage deviation modulus, with bias and accuracy factor values approximately equal to one.

Alginate-gelatin hydrogels are extensively used in bioengineering. However, despite different formulations being utilized for growing different cell types in vitro, their pH and its effect, together with the crosslinking ions, of those formulations are still infrequently assessed. In this work we studied how these elements can affect hydrogel stability and printability and influence U2OS and NIH/3T3 cell viability and metabolism on the resulting 3D prints. In this context, 6% alginate + 2% gelatin hydrogels were prepared with 0.1 M MES buffer with pH 5.5, 6.5, 7.0 or 8.0, printed by extrusion-based 3D printing, and crosslinked immediately after printing with either CaCl2 or BaCl2. Our results showed that both the buffer pH and the crosslinking ion (Ca2+ or Ba2+) influence the swelling and degradation rates of the prints. Moreover, the buffer pH influenced the printability of the hydrogel in air, but when printed directly in a fluid-phase CaCl2 or BaCl2 crosslinking bath. In addition, both U2OS and NIH/3T3 cells showed greater cell metabolic activity on one-layer prints crosslinked with Ca2+. Besides, Ba2+ increased cell death of NIH/3T3 cells while had no effect on the U2OS cell viability. The pH of the buffer also caused an important impact on the cell behaviour. U2OS cells showed a 2.25-fold cell metabolism increase on one-layer prints prepared at pH 8.0 in comparison to those prepared at pH 5.5. Whereas, NIH/3T3 cells showed greater metabolism on one-layer prints with pH 7.0. Finally, we observed a difference on cell arrangement of the U2OS cells growing on prints prepared from hydrogels with acidic buffer in comparison to cells growing on those prepared using neutral or basic buffer. These results show that both pH and crosslinking ion influence hydrogel strength and cell behaviour.

The photoelectrochemical (PEC) conversion of organic small molecules offers a dual benefit of synthesizing value-added chemicals and concurrently producing hydrogen (H2). Ethylene glycol, with its dual hydroxyl groups, stands out as a versatile organic substrate capable of yielding various C1 and C2 chemicals. In this study, we demonstrate that pH modulation markedly enhances the photocurrent of BiVO4 photoanodes, thus facilitating the efficient oxidation of ethylene glycol while simultaneously generating H2. Our findings reveal that in a pH=1 ethylene glycol solution, the photocurrent density at 1.23 V vs. RHE can attain an impressive 7.1 mA cm−2, significantly surpassing the outputs in neutral and highly alkaline environments. The increase in photocurrent is attributed to the augmented adsorption of ethylene glycol on BiVO4 under acidic conditions, which in turn elevates the activity of the oxidation reaction, culminating in the maximal production of formic acid. This investigation sheds light on the pivotal role of electrolyte pH in the PEC oxidation process and underscores the potential of the PEC strategy for biomass valorization into value-added products alongside H2 fuel generation.

The purpose of current research work was to formulate and typify gelatin and poly(vinyl) alcohol (Gel/PVA) hydrogel which would be highly pH-responsive and can able to accomplish targeted delivery of methotrexate in order to treat the colo-rectal pathologies. The primed gel/pva hydrogel discs were subjected to various physicochemical techniques i.e. swelling, diffusion co-efficient, sol-gel analysis and porosity using three altered sorts of pH (1.2, 6.8 & 7.4) phosphate buffer solutions for assessment/evaluation, and their characterization was done through Fourier transform infrared spectroscopy (FTIR) and thermal gravimetric analysis (TGA). Shape alteration and controlled methotrexate of release of Gel/PVA hydrogel have been done using three type of pH (1.2, 6.8 & 7.4) phosphate buffer mediums. Methotrexate was loaded through in-situ drug loading method due to hydrophobicity. Different kinetic models (first order & zero order kinetic), Higuchi model and Krosmere peppas model/Power law were applied to manipulate the drug release data. Physicochemical evaluation tests and drug release profile results were found insignificant (p< 0.05) in various pH mediums and dependent upon polymers concentration pH of medium and cross-linker amount. Kinetic model disclosed that release of methotrexate from Gel/PVA hydrogel follow non-Fickian diffusion method. It became concluded from this research work that release of methotrexate Gel/PVA hydrogel in targeted colon area can be achieved for treating colo-rectal disorders.

Coffee and caffeine have been used as solar absorbers and also to increase the thermal stability and efficiency of perovskite solar cells. In this work, we report the sensing of extremely alkaline pH by colloidal coffee solution aided by generation of an optical absorption band in the near-UV region. This generation of absorption band could be explained by the orientation induced dipole-dipole interactions arising from differing caffeine-solvent interactions with varying pH. Such a generation leads to the lowering of direct as well as indirect bandgaps from 4 eV-->2.8 eV& 3.4 eV-->2.5 eV, respectively. We also estimate the changes in optical energy storage efficiency, inferring it to be highest for pH 11 having the highest intensity of the generated absorption band (λ_abs≈360 nm). With these observations and further deductions, the work reported in this paper would be of immense interest to the researchers working in the field of development of chemical pH sensors and also in the development of novel UV absorbers.

Current generation witnesses a huge interest in optical waveguide due to their salient feature such as low cost, immune to electromagnetic interference, easy to multiplex, compact size, etc. These features of the optical fibers makes it an useful tool for various sensing applications including medicine, automotive, biotechnology, food quality control, aerospace, physical and chemical monitoring etc. Among all the reported application, the device has been widely exploited to measure the physical and chemical variation in surrounding environment. Optical fiber based temperature sensor plays a crucial role in this decade to detect high fever and tackle COVID like pandemic. Recognizing the major developments in the field of the optical fibers, this article aims to provide recent progress in temperature sensor utilizing several sensing configuration including standard fiber, photonic crystal fiber, and Bragg grating fibers. Additionally, the article also highlights the advantages, limitations, and future possibilities in this area.

It is since long known, that SAW devices, resonators as well as delay lines, can be used as passive wireless sensors for physical quantities like temperature and pressure as well as gas sensors or ID-Tags. The sensors are robust, work passively without battery, can be applied at high temperatures and provide a high resolution. Nevertheless, if the devices should be readout wirelessly in an industrial environment, several constraints have to be taken into account, especially when more than one quantity or device needs to be measured at the same time. The paper addresses the challenges that have to be tackled when establishing multi-sensor-wireless-readout for industrial applications. Major issues here are the legal ISM-band regulations, as well as sampling time and costs, which impose severe restrictions to any system design. We describe several design approaches and their constraints. We have successfully designed sensors based on reflective delay lines that allow the parallel readout of four independent temperature sensors in the 2.45 GHz ISM-band. These devices have been fabricated, positively tested and demonstrate the applicability of SAW sensors for industrial applications.

Carbon nanotubes have been attracting considerable interest among material scientists, physicists, chemists and engineers for almost 30 years. Owing to their high aspect ratio, coupled with remarkable mechanical, electronic and thermal properties, carbon nanotubes have found application in diverse fields. In this review, we will cover the work on carbon nanotubes used for sensing applications. In particular, we will see examples where carbon nanotubes act as main players in devices sensing biomolecules, gas, light or pressure changes. Furthermore, we will discuss how to improve the performance of carbon nanotube-based sensors after proper modification.

The fourth industrial revolution, also known as Industry 4.0, has led to an increased transition towards automation and reliance on data-driven innovations and strategies. Companies in the manufacturing sector are heavily integrating Industry 4.0 technologies, including cloud compu-ting, cyber-physical systems (CPS), big data analytics, horizontal and vertical system integration, the internet of things (IoT), and additive manufacturing (3d printing). The interconnected systems and processes have significantly increased operational efficiency, enhanced organizational capacity to monitor and control functions, reduced costs, and improved product quality. One significant way that companies have achieved these benefits is by integrating diverse sensor technologies within these innovations, allowing critical data collection on products, equipment performance, and maintenance. The sensors connect systems and machines, allowing them to communicate and track operations for enhanced operations. While numerous research has been conducted to show the role of sensors in industry 4.0, limited studies show how these innovations can leverage product design to maximize benefits and opportunities. Given the rapidly changing market conditions, Industry 4.0 requires new products and business models to ensure companies adjust to the current and future changes. These requirements call for the evolutions in product design processes to accommodate design features and principles applicable in the current dynamic business environment. This research paper employs a systematic bibliometric literature review (LRSB) methodology to explore and synthesize data on how Industry 4.0 and sensors can leverage product design. The results show that various product design features create opportunities to be leveraged to guarantee the success of Industry 4.0 and sensor technologies. However, the research also identifies numerous challenges that undermine the ongoing transition towards intelligent factories and products.

Terrestrial algae are the group of photosynthetic organisms, which can survive in extreme conditions. pH is one of the most important factor, influencing on distribution of algae, both in aquatic and terrestrial ecosystems. The influence of different pH levels on cell volume and other morphological characters of authentic and reference strains of Chlorella vulgaris, Bracteacoccus minor, Pseudoccomyxa simplex, Chlorococcum infusionum, and Vischeria magna were studied. Chlorella vulgaris and Pseudoccomyxa simplex were the most resistant species, retaining its morphology in range of pH 4-11,5. The change of pH towards acidic and alkaline levels caused the increase of volume of Pseudoccomixa simplex and Vischeria magna cells according to polynomial regression model. Volume of Chlorella vulgaris cells increased from low to high pH according to linear regression model. Changes of pH levels did not have a significant impact on volume of Bracteacoccus minor and Chlorococcum infusionum cells. Low and high levels of pH caused thickening of cell walls of Chlorococcum infusionum and increase of oil containing substances in Vischeria magna and Bracteacoccus minor cells. Our study revealed a high resistance of studied species to extreme level of pH, which allow recommend these strains for broader use in biotechnology and natures protection.

In Philadelphia chromosome positive B-cell (Ph+) acute lymphoblastic leukemia (LLA), growing evidence has ac-cumulated about the efficacy of low-intensity and chemo-free regimens. Our objective was to analyze all recent trials evaluating these treatments and to compare them in terms of efficacy. We applied the Shiny method, an artificial intelligence technique, to analyze Kaplan-Meier curves and reconstruct patient-level data. Reconstructed patient data were then evaluated through standard survival statistics and subjected to indirect head-to-head treatment comparisons. The endpoint was progression-free survival (PFS). Based on 848 reconstructed patients, 9 trials were analyzed. The survival data from these trials were pooled into three types of treatments: i) treatments based on ty-rosine kinase inhibitors (TKIs) combined with reduced-intensity chemotherapy (denoted as TKICHE); ii) TKIs as-sociated to steroids with no chemotherapy (TKISTE); iii) chemotherapy-free combinations of blinatumomab plus TKIs (TKIBLI). According to the Shiny method, the three PFS curves were reported in a single Kaplan-Meier graph and subjected to survival statistics. In terms of PFS, TKIBLI ranked first, TKICHE second, and TKISTE third; the differences between these three regimens were statistically significant. This multi-treatment Kaplan-Meier graph, generated through the Shiny method, summarized the current evidence on these treatments in both qualitative and quantitative terms.

Strontium (Sr) is a trace element in human body that able to promote bone formation and inhibit bone absorption. The conversion coating of strontium phosphate (Sr-P) on the surface of titanium (Ti) can improve its biological properties, and has a wide application prospect in the fields of dentistry and orthopedics. In this present study, Sr-P coatings with SrHPO4 and Sr3(PO4)2 crystals on Ti are prepared by phosphate chemical conversion (PCC) treatment. And the effect of pH on the properties of Sr-P coatings is researched. The results prove that phase composition, morphology and corrosion resistance of coated Ti are different with the pH values in PCC solution. The morphologies of conversion deposition on Ti change from plat-like to cluster-like, and then homogeneous microcrystals, as pH value changed from 2.50 to 3.25. Only discrete SrHPO4 crystals are generating on substrate at lower pH value, while relative stable Sr3(PO4)2 and SrHPO4 crystals are growing and subsequently forming an integrated coating on Ti as pH is higher than 2.50. The corrosion resistance of coated Ti improves comparing with that of bare Ti because of forming Sr-P coatings with Sr3(PO4)2 phase. In addition, it is indicated that the Sr-P coatings can improve the adhesion and differentiation of BMSCs.

Bone fractures are very common in the geriatric population and poses a great economic burden worldwide. While traditional methods for repairing bone defects have primarily been autografts, there are several drawbacks limiting its use. Bone graft substitutes have been used as alternative strategies to improve bone healing. However, there remains several impediments to achieving the desired healing outcomes. Injectable hydrogels have become attractive scaffold materials for bone regeneration given their high performance in filling irregularly sized bone defects, ability to encapsulate cells and bioactive molecules, and mimic the native ECM of bone. We investigated the use of an injectable chitosan-based hydrogel scaffold to promote differentiation of preosteoblasts in vitro. The hydrogels were characterized by evaluating cell homogeneity, cell viability, rheological and mechanical properties, and differentiation ability of preosteoblasts in hydrogel scaffolds. Cell-laden hydrogel scaffolds exhibited shear thinning behavior and the ability to maintain shape fidelity after injection. The CNC-CS hydrogels exhibited higher mechanical strength and significantly upregulated the osteogenic activity and differentiation of preosteoblasts as shown by ALP activity assays and histological analysis of hydrogel scaffolds. These results suggest that this injectable hydrogel is suitable for cell survival, can promote osteogenic differentiation of preosteoblasts, and structurally support new bone growth.

: In Philadelphia chromosome positive B-cell (Ph+) acute lymphoblastic leukemia (LLA), growing evidence has accumulated about the efficacy of low-intensity and chemo-free regimens. Our objective was to analyse all recent trials evaluating these treatments and to compare them in terms of efficacy. We applied the Shiny method, an artificial intelligence technique, to analyse Kaplan-Meier curves and reconstruct patient-level data. Reconstructed patient data were then evaluated through standard survival statistics and subjected to indirect head-to-head treatment comparisons. The endpoint was progression-free survival (PFS). Based on 562 reconstructed patients, 8 trials were analyzed. The survival data from these trials were pooled into three types of treatment: i) treatments based on tyrosine kinase inhibitors (TKIs) combined with reduced-intensity chemotherapy (denoted as TKICHE); ii) TKIs associated to steroids with no chemotherapy (TKISTE); iii) chemotherapy-free combinations of blinatumomab plus TKIs (TKIBLI). According to the Shiny method, the three PFS curves were reported in a single Kaplan-Meier graph and subjected to survival statistics. In terms of PFS, TKIBLI ranked first, TKICHE second, and TKISTE third; the differences between these three regimens were statistically significant. In conclusion, the multi-treatment Kaplan-Meier graph generated in this study has effectively summarized the current evidence on these treatments in comparative terms.

The paradigm of drug delivery via nano- and microcarriers is one of the leading ideas that enable overcoming the limitations of traditional chemotherapy. The trend toward more complex drug carriers capable of multifunctionality is observed in the literature. To date, prospects of stimuli-responsive systems to control the cargo release in the lesion nidus are widely accepted. Both endogenous and exogenous stimuli are employed for this purpose, however, endogenous pH is one of the most common triggers. Unfortunately, scientists face difficulties in the implementation of this idea since a range of biological barriers, drug bioavailability issues, and challenges in the synthesis of carriers with required properties have arisen. Here, we discuss fundamental strategies of pH-responsive drug delivery as well as limits in its application and reveal the main problems, weak sides, and reasons for poor clinical results. Also, we have made an attempt to formulate the profiles of "ideal" drug carrier in the frame of different strategies and considered recently published studies through the lens of these profiles. This approach enables the identification of current trends and promising vectors in the development of pH-responsive drug delivery systems, as well as challenges to be resolved in the next generation of carriers.

PH value is one of the most significant ecological factors affecting the survival and growth of aquatic organisms. But the effect and tolerance of pH value on many aquatic species are still unknown. This study mainly investigated the effects of pH value on the hatching rate of eggs, the adaptability of newly hatched larva fish and the survival of 3-months-old juvenile fish of Takifugu obscurus. Water pH values can cause a great impact on Takifugu obscurus lives, when the fertilized eggs of Takifugu obscurus were incubated at pH 5.0, 6.0, 7.0, 8.0, 8.3 (control group), 9.0, 10.0 and 11.0 respectively. Under the pH of 5.0, 6.0, 10.0 and 11.0, the hatching rate and speed is greatly reduced and the deformity rate of hatching larvae is greatly increased; When the hatch-pH value was 6.0, the acid adaption of hatched larvae was significantly enhanced, but alkali adaptation was weakened; Under the condition of pH gradient of 6.0, 6.4, 6.8, 7.0, 8.0, 8.3, 9.0, 10.0, 10.2, 10.5, 11.0 and 12.0, survival time and survival rate of juvenile fish show a significant difference. Especially when the pH value was 6.0 and 12.0, juvenile fish die immediately after swimming quickly. Within 24 h, half of the fish died at the pH of 6.4 and 10.3, and within 48 h, half died at the pH of 7.1 and 9.9. In addition, the gradual pH value group in which the pH value gradually decreased or increased had stronger acid-base adaptability and a higher survival rate than the acute experimental group. The above results show the relationship between pH value and survival of Takifugu obscurus, which can provide more reference for the introduction of Takifugu obscurus into saline-alkali land in the future. Additionally, the incubated pH value can influence the pH tolerance of Takifugu obscurus, which can be applied to the breed improvement into an appropriate water environment.

Today, there are commercially available high-performance electric wheelchairs, capa-ble of responding to strong limitations. However, despite these advancements, there is a significant portion of the population with severe disabilities who cannot access this mobility solution due to safety reasons. Indeed, either due to motor issues preventing reliable control of the wheelchair's commands, or associated visual or cognitive pathologies, the use of an electric wheelchair by these individuals would put them at risk and could also constitute a danger to those around them. This is why our research team is working on the development of augmented wheelchairs that allow a greater autonomy. We are mainly developing a system compatible with all electric wheel-chairs on the market, capable of making them anti-collision and anti-fall on uneven ground (sidewalks, stairs, etc.). In this article, we present our solution regarding the anti-collision function, in particular the sensors used to do this, as well as the strategy. We will focus on the shortcomings and weaknesses of various types of sensors and demonstrate how, by combining them in a certain way, we can develop a collision avoidance device capable of managing the diversity of everyday life situations. The two types of sensors that will be combined here are an in-house developed special near infrared sensor from the laboratory and a commercially available ultrasonic sensor. We will present the internal operation of the sensors, their limitations, experimental tests involving integration with the wheelchair, and the structure of the complete device.

This paper provides a data set collected with an underground shaft mobile mapping system equipped with rotated Velodyne VLP-16, Velodyne Ultra Puck VLP-32c, Livox Tele-15, and IMU Xsens MTi-30. The ground truth data was acquired with a geodetic survey including 15 ground control points and 6 Faro Focus 3D Terrestrial Laser Scanner stations of a total 273,784,932 of 3D measurement points. The aim of the paper is to describe the data set of a mining shaft. Obtained mobile mapping data can be the basis for detailed analyzes of the technical condition of the shaft. This data set provides an end-user case study of realistic applications in mobile mapping technology. It provides ground truth data, mobile mapping data and software tools for manipulation and visualization. The project is released and maintained at https://michalpelka.github.io/mine-mapping-dataset/.

Vehicle safety promises to be one of the Advanced Driver Assistance System (ADAS) biggest benefits. Higher levels of automation remove the human driver from the chain of events that can lead to a crash. Sensors play an influential role in vehicle driving as well as in ADAS by helping the driver to watch the vehicle’s surroundings for safe driving. Thus, the driving load is drastically reduced from steering as well as accelerating and braking for long-term driving. The baseline for the development of future intelligent vehicles relies even more on the fusion of data from surrounding sensors such as Camera, Lidar and Radar. These sensors not only need to perceive in clear weather but also need to detect accurately adverse weather and illumination conditions. Otherwise, a small error could have an incalculable impact on ADAS. As most of the current study is based on indoor or static testing. In order to solve this problem, this paper designs a series of dynamic test cases with the help of outdoor rain and intelligent lightning simulation facilities to make the sensor application scenarios more realistic. As a result, the effect of rainfall and illumination on sensor perception performance is investigated. As speculated, the performance of all automotive sensors is degraded by adverse environmental factors, but their behaviour is not identical. Future work on sensor model development and sensor information fusion should therefore take this into account.

Phenology is one of the ubiquitous fingerprints of climate change on our ecosystems. Monitoring the spatiotemporal patterns of vegetation phenology is thus critical. A wide range of sensors have been used to monitor vegetation phenology. Sensor point of view and resolution can potentially impact estimates of phenology. We compared three different sensors from three different remote sensing platforms—a UAV mounted RGB camera, an under canopy, upward facing hemispherical camera with R, G and NIR capabilities, and a tower mounted RGB PhenoCam—to estimate spring phenological transition in a mixed-species temperate forest in central Virginia, USA. Our study had two objectives: 1) to compare the above- and below- canopy inference of canopy greenness (green chromatic coordinate and normalized difference vegetation index) and canopy structural attributes (leaf area and gap fraction) by matching under-canopy hemispherical photos with high spatial resolution (0.03 m) drone imagery to find the appropriate spatial coverage and resolution for comparison; 2) to compare how each sensor performed in estimating the temporality of the spring phenological transition. We find that a spatial buffer of 20 m radius for UAV imagery is most closely comparable to under-canopy imagery in this system. Sensors and platforms agree within +/- 5 days of when canopy greenness stabilizes from the spring phenophase into the growing season. This work has implications for paring UAV imagery with both tower-based observation platforms, as well as plot-based studies (e.g. long-term monitoring, existing research networks, permanent plots).

: Over time, we have come to recognize a very complex network of physiological changes enabling wound healing. An immunological process enables the body to distinguish damaged cells and begin a cleaning mechanism by separating damaged proteins and cells with matrix metallopro-teinases, a complement reaction, and free radicals. A wide variety of cell functions help to rebuild new tissue, dependent on energy provision and oxygen supply. Like in an optimized "biorector," disturbance can lead to prolonged healing. One of the earliest investigated local factors is the pH of wounds, studied in close relation to the local perfusion, oxygen tension, and lactate concentration. Granulation tissue with the wrong pH can hinder fibroblast and keratinocyte division and pro-liferation, as well as skin graft takes. Methods for influencing the pH have been tested, such as occlusion and acidification by the topical application of acidic media. In most trials, this has not changed the wound's pH to an acidic one, but it has reduced the strong alkalinity of deeper or chronic wound. Energy provision is essential for all repair processes. New insights into the metabolism of cells have changed the definition of lactate from a waste product to an indispensable energy provider in normoxic and hypoxic conditions. Neovascularization depends on oxygen provision and lactate, signaling hypoxic conditions even under normoxic conditions. An appropriate pH is necessary for successful skin grafting; hypoxia can change the pH of wounds. This review describes the close interconnections between the local lactate levels, metabolism, healing mechanisms, and pH. Furthermore, it analyzes and evaluates the different possible ways to support metabolism, such as lactate enhancement and pH adjustment. The aim of wound treatment must be the optimization of all these components. Therefore, the role of lactate and its influence on wound healing in acute and chronic wounds will be assessed.

Structural and morphological properties of the hydronium-potassium jarosite microstructures were investigated in this work, and their electrical properties were evaluated. All microstructures were synthesized at a reasonable temperature of 343 K with a reduced reaction time of 3 hours. Increase in the pH from 0.8 to 2.1 decreased the particle sized from 3 µm to 200 nm and increasing the aging time from 0, 3 to 7 days resulted in semispherical, spherical and euhedreal jarosite structures, respectively. A Rietveld analysis also was done, finding that increasing pH, the amount of hydronium substitution by potassium in the cationic site also increases, having a 77.72 % of hydronium jarosite (JH) plus 22.29 % potassium jarosite (JK) at pH 0.8; 82.44 % (JH) and 17.56 % (JK) at pH 1.1, and 89.98 % (JH) plus 10.02 % (JK) at pH 2.1. The results obtained in this work show that the obtained hydronium potassium jarosite microstructures with reduced particle size and euhedreal morphology can be used as anode materials for improving the life time of lithium ion batteries, due that during the analysis of the voltage obtained using electrodes made with this particles and graphite, this ranged from 0.89 to 1.36 V.

Novel multifunctional fluorescent chemosensors composed of electrospun (ES) nanofibers with high sensitivity toward pH, mercury ions (Hg²⁺), and temperature were prepared from poly(N-Isopropylacrylamide-co-N-methylolacrylamide-co-rhodamine derivative) (poly(NIPAAm-co-NMA-co-RhBN2AM)) by employing electrospinning process. NIPAAm and NMA moieties provide hydrophilic and thermo-responsive properties (absorption of Hg²⁺ in aqueous solutions), and chemical cross-linking sites (stabilization of the fibrous structure in aqueous solutions), respectively. The fluorescent probe, RhBN2AM is highly sensitive toward pH and Hg²⁺. Synthesis of poly(NIPAAm-co-NMA-co-RhBN2AM) with different compositions were carried on via free-radical polymerization. ES nanofibers prepared from sensory copolymers with a 71.1:28.4:0.5 NIPAAm: NMA: RhBN2AM ratio (P3 ES nanofibers) exhibited significant color change from nonfluorescent to red fluorescence while sensing pH or Hg²⁺, and high reversibility of on/off switchable fluorescence emission when Hg²⁺ and ethylenediaminetetraacetic acid (EDTA) were sequentially added. The P3 ES nanofibrous membranes had a higher surface-to-volume ratio to enhance their performance than did the corresponding thin films. In addition, the fluorescence emission of P3 ES nanofibrous membranes exhibited second enhancement above the lower critical solution temperature. Thus, the ES nanofibrous membranes prepared from P3 with on/off switchable capacity and thermo-responsive characteristics can be used as multifunctional sensory devise for specific heavy transition metal (HTM) in aqueous solutions.

Cathepsin D (CatD; EC 3.4.23.5) family peptidases of parasitic organisms are regarded as potential drug targets as they play critical roles in the physiology and pathobiology of parasites. Previously, we characterized the biochemical features of cathepsin D isozyme 2 (CatD2) in the carcinogenic liver fluke Clonorchis sinensis (CsCatD2). In this study, we performed all-atomic molecular dynamics simulations by applying different systems for the ligand-free/bound forms under neutral and acidic conditions to investigate the pH-dependent structural alterations and associated functional changes in CsCatD2. CsCatD2 showed several distinctive characteristics as follows: 1) CsCatD2-inhibitor complex formed more hydrogen bonds; 2) acidic pH caused major conformational transitions from open to closed state in this enzyme; 3) neutral pH induced displacement of the N-terminal part to hinder the accessibility of the active site and open allosteric site of this enzyme; and 4) the flap dynamics metrics, including distance (d1), TriCα angles (θ1 and θ2), and dihedral angle (ϕ), account for the asymmetrical twisting motion of the active site of this enzyme. These findings provide an in-depth understanding of the pH-dependent structural dynamics of CsCatD2 and basic information for the rational design of an inhibitor as a drug targeting CsCatD2.

The high hydrophobicity of fullerenes and the resulting formation of aggregates in aqueous solutions hamper the possibility of their exploitation in many technological applications. Noncovalent bioconjugation of fullerenes with proteins is an emerging approach for their dispersion in aqueous media. Contrary to covalent functionalization, bioconjugation preserves the physicochemical properties of the carbon nanostructure. The unique photophysical and photochemical properties of fullerenes are then fully accessible for applications in nanomedicine, sensoristic, biocatalysis and materials science fields. However, proteins are not universal carriers. Their stability depends on the biological conditions for which they have evolved. Here we present two model systems based on pepsin and trypsin. These proteins have opposite net charge at physiological pH. They recognize and disperse C₆₀ in water. UV-Vis spectroscopy, zeta-potential and atomic force microscopy analysis demonstrates that the hybrids are well dispersed and stable in a wide range of pH’s and ionic strengths. A previously validated modelling approach identifies the protein-binding pocket involved in the interaction with C₆₀. Computational predictions, combined with experimental investigations, provide powerful tools to design tailor-made C₆₀@proteins bioconjugates for specific applications.

This paper provides an overview of flexible and wearable respiration sensors with emphasis on their significance in healthcare applications. The paper classifies these sensors based on their operating frequency distinguishing between high-frequency sensors which operate above 10 MHz and low-frequency sensors. The operating principles of breathing sensors as well as the materials and fabrication techniques employed in their design are addressed. The research highlights the need for robust and flexible materials to enable the development of reliable and comfortable sensors. Finally, the paper presents potential research directions and proposes research challenges in the field of flexible and wearable respiration sensors. Thus, identifying emerging trends and gaps in knowledge, it encourages further advancements and innovation in the rapidly evolving domain of flexible and wearable sensors.

Palpation is a simple but effective method to differentiate tumors from healthy tissues. Development of miniaturized tactile sensors embedded on endoscopic or robotic devices are the key toward precise palpation diagnosis and the subsequent timely treatment. This paper reports on the fabrication and characterization of a novel tactile sensor with mechanical flexibility and optical transparency that can be easily mounted on soft surgical endoscopes and robotics. Utilizing the pneumatic sensing mechanism, the sensor offers a high sensitivity of 1.25 mbar and negligible hysteresis, enabling the detection of phantom tissues with different stiffnesses ranging from 0 to 2.5 MPa. Our configuration combining pneumatic sensing and hydraulic actuating also eliminates electrical wiring from the functional elements located at the robot end-effector, thereby enhancing the system safety. The optical transparency path in the sensors together with its mechanical sensing capability open interesting possibility in early detection of solid tumor as well as in the development of all in-one soft surgical robots that can perform visual/mechanical feedback and optical therapy.

Temperature measurements are of great importance in many fields of human activities, including industry, technology, and science. For example, obtaining a certain temperature value or a sudden change in it can be the primary control marker of a chemical process. Fiber optic sensors have remarkable properties giving a broad range of applications. They enable continuous real-time temperature control in difficult-to-reach areas, in hazardous working environments (air pollution, chemical or ionizing contamination), and the presence of electromagnetic disturbances. The use of fiber optic temperature sensors in polymer technology can significantly reduce the cost of their production. Moreover, the installation process and usage would be simplified. As a result, these types of sensors would becoming increasingly popular in industrial solutions. This review provides a critical overview of the latest development of fiber optic temperature sensors based on Fabry-Perot interferometer made with polymer technology.

Since 1970s, a great deal of attention has been paid to the development of semiconductor–based biosensors because of the numerous advantages they offer, including high sensitivity, faster response time, miniaturization, and low–cost manufacturing for quick biospecific analysis with reusable features. Commercial biosensors have become highly desirable in the fields of medicine, food, environmental monitoring as well as military applications (e.g., Hoffmann–La Roche, Abbott Point of Care, Orion High technologies, etc.), whereas increasing concerns on the food safety and health issues have resulted in the introduction of novel legislative standards for these sensors. Numerous devices have been developed for monitoring of biological–processes such as nucleic–acid hybridization, protein–protein interaction, antigen–antibody bonds and substrate–enzyme reactions, just to name a few. Since 1980s scientific interest moved to the development of semiconductor–based devices which also include integrated front–end electronics, such as the extended–gate–field–effect–transistor biosensor which is one of the first miniaturized chemical sensors. This work is intended to be a review of the state of the art focused on the development of biosensors based extended–gate–field–effect–transistor within the field of bioanalytical applications, which will highlight the most recent research works reported in the literature. Moreover, a comparison among the diverse EGFET devices will be presented giving particular attention to the materials and technologies.

We address Multi-Wall Carbon NanoTubes (MWCNTs) for structural health monitoring in adhesive bonds such as in building structures. MWCNT-loaded composites are employed to sense strain changes under tension load using an AC impedance measurement setup. Different weight percentages of 1, 1.5, 2 and 3 wt.% MWCNT are added to the base epoxy resin using different dispersion times, i.e. 5, 10 and 15 minutes. The equivalent parallel resistance of the specimens is measured by applying an alternating voltage at different frequencies. To determine the mechanical as well as sensory properties, the specimens are subjected to a tensile test with concurrent impedance measurement. Using alternating voltage, a higher sensitivity of the impedance reading can be achieved. Employing these sensors in buildings and combining the readings of a network of such devices can significantly improve the buildings’ safety. Additionally, networks of such sensors can be used to identify necessary maintenance actions and locations.

Promoter is a small region of DNA sequence in response to various transcription factors, which initiates a particular gene expression. The promoter-engineered bio-sensor can activate or repress gene expression through transcription factor recognizing specific molecules, such as polyamine, sugars, lactams, amino acids, organic acids or redox molecule, however, the reported applications of promoter enhanced bio-sensor are not too much. This review paper highlights the strategies of construction of promoter-gene engineered bio-sensor with human and bacteria’s genetic promoter array for high-throughput screening (HTS) molecular drugs, study of membrane protein’s localization and nucleocytoplasmic shuttling mechanism of regulating factor, enzyme activity, detection of the toxicity of intermediate chemicals, and probing bacteria density to improve value-added product titer. These bio-sensors’s sensitivity and specificity can be further improved by proposed approaches of Mn²⁺ and Mg²⁺ added random Error-prone PCR and site-directed mutagenesis which is applied for construction of bacteria’s “mutant library”. It is expected to establish flexible HTS platform (Bio-sensor array) to large-scale screen transcription factor-acting drugs, reducing the toxicity of intermediate compounds, and constructing gene dynamic regulatory system in “push and pull” mode to effectively regulate the valuable medicinal product production. This proposed novel promoter-engineered biosensors aided synthetic genetic circuit construction will maximize the efficiency of bio-synthesis of medicinal compound, which will greatly promote the development of microbial metabolic engineering and biomedical science.

Smart sensors based on graphene field effect transistor and biologically receptors are regarded as a promising nanomaterial that could be the basis for future generations of selective real-time monitoring of target analytes and smaller electronics. So the purpose of this paper is to provide details a real-time and selective explosive sensor based on GFETs and PDA-based lipid membranes coupled with biologically inspired TNT peptide receptors. Following an introduction, this paper describes the way of fabrication of the GFETs device by investigation methods for transferring graphene sheet from Cu substrates to target substrates, which is functionalized by the TNT peptide receptors, in order to offer a system which has the capability of answering the presence of related target molecules. Field effet transistor was fabricated using graphene as a channel and monitored by the source-drain current and back-gate voltage curves in the measurement. The transport property changed compared to that of the FET made by intrinsic graphene, that is, the Dirac point position moved from positive Vg to negative Vg, indicating the transition of graphene from p-type to n-type after annealing in TNT, and GFET sensor show good sensitivity and selectivity response.

Vitamin D3 deficiency is a global phenomenon, which can be coped with supplementation and food fortification. However, vitamin D3 bioaccessibility may depend on factors, such as matrix composition and interactions throughout the gastrointestinal tract. This research focused on the effect of different matrices on vitamin D3 content during digestion, and the effect of pH on its bioaccessibility. The INFOGEST protocol was employed to simulate digestion. Three different types of commercial supplements, two foods naturally rich in vitamin D3, and three fortified foods were investigated. High-Performance Liquid Chromatography was used to determine the vitamin D3 initial content in supplements and foods, as well as after each digestion stage. Results indicated that foods exhibited higher bioaccessibility indices compared to supplements, and a higher percentage retention at the end of the gastric phase. The pH study revealed a positive correlation between increased gastric pH and the corresponding content of vitamin D3. Interestingly, exposing the matrix to low pH during the gastric phase resulted in an increased intestinal content of D3. Vitamin D3 is more bioaccessible from foods than supplements, and its bioaccessibility is susceptible to changes in gastric pH. Fasting conditions (i.e. gastric pH=1) enhances vitamin’s bioaccessibility.

The practical application of a pH-responsive Nanoparticle Drug Delivery System (NDDS) in cancer treatment is often hampered by several issues such as the protection of therapeutic molecules from external stresses, inefficient targeted delivery, sustained drug release, and poor efficacy. This study presents an effective design strategy for the synthesis of a pH-sensitive controlled hydrophobic drug delivery method based on the formulation of chitosan (CS)-coated mesoporous silica nanoparticles (MSNs) through the sol-gel method, where hydrolysis takes place in the acidic medium followed by polycondensation of the hydrolyzed products. For this purpose, NH2 modified-MSNs were prepared by using tetraethyl orthosilicate (TEOS) as precursor and cetyltrimethylammonium bromide (CTAB) as a template, and 3-aminopropyltriethoxysilane (APTES) for amine modification, followed by hydrophobic drug loading and CS coating of various concentrations. Camptothecin (CPT) was used as a model drug. Fabricated monodispersed functionalized nanoparticles had sizes ranging from 200nm to 245nm with an encapsulation efficiency as high as 90%. The highest encapsulation efficiency was found for 1% CS coating, which released 50% drug in 120h at pH 6.4 and 20% at pH 7.4 respectively. These nanoformulations exhibited pH-responsive release patterns of CPT under two different pH values (pH=7.4 and pH=6.4). These results contribute to the optimization of NDDS, with potential implications for nanoformulations designed for controlled and sustained drug release particularly to tumors without affecting healthy cells owing to differences in the pH of the tumor microenvironment and the normal physiological environment of cells.

The aim of the current study was to develop and evaluate the therapeutic potential of apocynin (APO) loaded pH-sensitive nanoparticles (NPs) based transdermal hydrogel for management of rheumatoid arthritis (RA). Slightly modified nanoprecipitation technique was used for preparation of polymeric nanoparticles. Optimization was done through design expert software. Optimized APO-NPs were loaded into carbopol-934 based hydrogel as final dosage form and further studied for physicochemical properties. Optimized APO-NPs formulation had a minimum particle size 63.44 nm, polydisperibility index 0.161, and zeta potential -15mV with a maximum encapsulation efficiency of 89%. In-vitro and ex-vivo studies of APO-NPs based hydrogel was performed at pH 5.5 (pH of normal skin) and 6.8 (pH of inflammed joint) showed a pH-responsive sustained drug release and increased penetration in comparison to free APO based hydrogel. The stability studies of APO-NPs based hydrogel were done to strengthen the potential use of the prepared formulation through transdermal route. Assessment and therapeutic efficacy of the prepared pH-sensitive nanocarriers system was evaluated in chronic inflammatory RA mice model. Parameters associated with chronic inflammation were investigated including behavioral changes and histopathological, and radiological x-rays images of joints of mice paws. In-vivo study depicts improvement in behavioral parameter, decline in synovial hyperplasia and bone structure restoration. In conclusion, APO loaded pH-sensitive NPs based transdermal is a promising carrier system that can effectively manage RA.

The influence of pH, temperature, biopolymer ratio, total concentration, and ionic concentration on the interaction between egg white protein (EWP) and chitosan (CS) was investigated through turbidity, zeta potential, and state diagram in our research. In addition, phase behavior was observed under various conditions. The turbidity of EWP remained low (turbidity&lt;0.03) and basically unchanged at a wide range of pH (4.0-8.0), while the turbidity of CS was slightly higher (turbidity&lt;0.2) after pH 7.0 than before. Moreover, under the same conditions, a sharply rising peak pattern was observed for the complex between EWP and CS. The maximum turbidity value was observed at 55°C, and the temperature had a mild effect on turbidity. The optimum EWP to CS ratio was found to be 12:1 based on the experiment of the turbidity curves and state diagrams influenced by different biopolymer mixing ratios. With the enhanced concentrations of total biopolymer, the maximum turbidity rose insignificantly above 0.1%.

We hypothesized that reticuloruminal temperature and pH, as well as cow activity, can be used as biomarkers for the early diagnosis of clinical mastitis in dairy cows. Therefore, we aimed to detect the relationship between reticuloruminal temperature and pH, cow activity, and clinical mastitis in dairy cows. We randomly selected cows with clinical mastitis and clinical healthy cows (HG) out of 600 milking cows. We recorded the following parameters during the experiment: reticulorumen tem-perature (RR temp.), reticulorumen pH (RR pH), and cow activity. We used smaXtec boluses (smaXtec animal care technology®, Graz, Austria). In this investigation, reticulorumen data ob-tained seven days before diagnosis were compared to HG data from the same time period. CM cows were observed on the same days as the healthy cows. The healthy group’s RR pH was 7.32% higher than that of cows with CM. Reticulorumen temperature was also 1.25% higher in the CM group than in the control group. The healthy group had a higher average value for walking activity and was 17.37% higher than the CM group. The data of reticulorumen pH changes during 24 h showed that during the day, the pH changed from 5.53 to 5.83 in the CM group. By contrast, pH changed from 6.05 to 6.31 in the control group. The lowest reticulorumen pH in the CM group was detected on the third day before diagnosis. It was 15.76% lower than the highest reticulorumen pH detected on the sixth day before diagnosis. The lowest reticulorumen pH in CM cows was detected at 0 and 1 days before diagnosis. It was 1.45% lower than the highest reticulorumen pH detected on the second day before diagnosis. The lowest walking activity in the CM group was detected 0 days before diagnosis, 50.60% lower than on the fifth day before diagnosis. The lowest walking activity was detected 0 days before diagnosis, 39.57% lower than on the seventh day before diagnosis. In this study, we found that reticuloruminal temperature, reticuloruminal pH, and cow ac-tivity could be used as biomarkers for the early diagnosis of clinical mastitis in dairy cows.

The objective of this study aimed to develop biodegradable calcium alginate microspheres carrying doxorubicin (Dox) at the micrometer-scale for sustained-release and the capacity of pH regulatory for transarterial chemoembolization. Ultrasonic atomization and CaCl2 cross-linking technologies were used to prepare the microspheres. A 4 by 5 experiment was first designed to identify imperative parameters. The concentration of CaCl2 and the flow rate of the pump were found to be critical to generate microspheres with a constant volume median diameter (~ 39 m) across 5 groups with different alginate:NaHCO3 ratios using each corresponding flow rate. In each group, the encapsulation efficiency was positively correlated to the Dox-loaded efficiency. Fourier-transform infrared spectroscopy showed that NaHCO3 and Dox were step-by-step incorporated into the calcium alginate microspheres successfully. Microspheres containing alginate:NaHCO3 = 1 exhibited rough and porous surfaces, high Young’s modulus and hardness. In each group with the same alginate:NaHCO3 ratio, the swelling rates of microspheres were higher in PBS containing 10% FBS compared to those in PBS alone. Microspheres with relative high NaHCO3 concentrations in PBS containing 10% FBS maintained better physiological pH and higher accumulated Dox release ratios. In two distinct hepatocellular carcinoma-derived cell lines, treatments with microspheres carrying Dox demonstrated that the cell viabilities decreased in groups with relative high NaHCO3 ratios in time- and dose-dependent manners. Our results suggested that biodegradable alginate microspheres containing relative high NaHCO3 concentrations improved the cytotoxicity effects in vitro.

Essential oils (EO) are a great antimicrobial resource against bacterial resistance in public health. Math models are useful describing the growth, survival, and inactivation of microorganisms against antimicrobials. We evaluated the antimicrobial activity of M. armillaris EO obtained from plants placed in the province of Buenos Aires (Argentina) against Staphylococcus aureus. Minimum Inhibitory and Bactericidal Concentrations were close and decreased slightly acidifying the medium from pH 7.4 to 6.5 and 5.0. This result was also evidenced by applying a sigmoid model, where the time and EO concentration necessaries to achieve 50% of the maximum effect decreased when medium was acidified. Moreover, at pH 7.4, applying the Gompertz model, we found that subinhibitory concentrations of EO decreased the growth rate and the maximum population density, and increased the latency period respect to the control. Additionally, we established physicochemical parameters for quality control and standardization of M. armillaris EO. Mathematical modelling allowed us to estimate key parameters in the behavior of S. aureus and Melaleuca armillaris EO at different pHs. This is interesting in situations where the pH changes are relevant, such as the control of intracellular infections in public health or the development of preservatives for food industry.

Galdieria maxima is a polyextremophilic alga capable of diverse metabolic processes. Ammonia is widely used in culture media typical of laboratory growth. Recent reports that this species can grow on wastes promote the concept that G. maxima might have biotechnological utility. Accordingly, there is a need to know the range of pH levels that can support G. maxima growth in a given nitrogen source. Here, we examined the combined effect of pH and nitrate/ammonium source on the growth and long-term response of the photochemical process to a pH gradient in different G. maxima strains. All were able to use differing nitrogen sources, despite both the growth rate and photochemical activity were significantly affected by the combination with the pH. All strains acidified the NH4+-medium (pH<3); only G. maxima IPPAS P507 showed reduced capacity in lowering the pH from 6.5. pH was a limiting factor in nitrate uptake at pH≥6.5; noteworthy, at pH 5 on nitrate G. maxima ACUF551 showed a good growth performance, despite the alkalization of the medium.

Monitoring the quality of stored bulk grain is generally done using temperature cables hung from silo roofs. Little investigation has been done into the effects of number of sensors and their placement in terms of reliability of the monitoring system with regard to making stored grain quality management decisions. A previously developed 3D finite element simulation model was verified and used to investigate these aspects. In the first study, a silo was loaded with about 228.6 Mg (9000 bushels) of maize and six temperature cables were placed in the grain mass. The maize was aerated continuously for a period of two weeks, and the cable sensor temperatures were compared to the predicted temperatures which were in close agreement with the observed readings. The standard error of prediction ranged from 2.0 to 3.7°C. In the second study, 15 and 30 sensors were placed at manufacturer recommended depths and horizontal locations in the grain mass of three silo sizes (i.e., 11x11, 14.6x14.6 and 14.6x18.3 m diameter by eave height). The average grain temperatures predicted by the 15 and 30 sensors over a one-year simulation period were compared to the average grain temperatures predicted for the entire grain mass (1968, 3052, and 3204 mesh nodes). The number of sensors needed to monitor stored grain temperatures reliably in the three silo sizes investigated heavily depended on whether the aeration control strategy achieved a sufficiently low temperature by the time the aeration fans were turned off and sealed ahead of the non-aerated storage period. Fifteen or 30 sensors were sufficient to monitor grain temperatures during the aeration cooling period but for the two larger silo sizes more than 30 sensors would be needed during the storage period. As silo size increased, and surface-to-volume ratio decreased, grain temperatures remained lower during the storage period. Results support the best management practice recommendation of leaving cooled grain cold and not warming it up in the spring ahead of storage into the summer.

The manuscript presents the use of three novel technologies for the implementation of wireless green battery-less sensors that can be used in agriculture. The three technologies, namely additive manufacturing, energy harvesting, and wireless power transfer from airborne transmitters carried from UAVs, are considered for smart agriculture applications. Additive manufacturing is exploited for the implementation of both RFID based sensors and passive sensors based on humidity sensitive materials. A number of energy-harvesting systems at UHF and ISM frequencies are presented which are in position to power platforms of wireless sensors, including humidity and temperature IC sensors used as agriculture sensors. Finally, in order to provide the wireless energy to the soil-based sensors with energy harvesting features, wireless power transfer (WPT) from UAV carried transmitters is utilized. The use of these novel technologies can facilitate the extensive use and exploitation of battery-less wireless sensors which are environmentally friendly and thus “green”. Additionally, it can potentially drive precision agriculture in the next era, through the implementation of a vast network of wireless green sensors which can collect and communicate data, to airborne readers so as to support with data the Artificial Intelligence and Machine Learning based, decision making platforms.

Glass has emerged as a highly versatile substrate for various sensor and MEMS packaging applications, including electromechanical, thermal, optical, biomedical, and RF devices, due to its exceptional properties such as high geometrical tolerances, outstanding heat and chemical resistance, excellent high-frequency electrical properties, and the ability to be hermetically sealed. In these applications, Through-Glass-Via (TGV) plays a vital role in manufacturing and packaging by creating electrical interconnections through glass substrates. This paper provides a comprehensive summary of the research progress in TGV fabrication along with their integrations, including through-via formation and metallization. The paper also reviews the significant qualification and reliability achievements obtained by the scientific community for TGV. Additionally, the paper summarizes the application of TGV technology in various sensors.

The application of movement-detection sensors is crucial for understanding surface movement and tectonic activities. The development of modern sensors has been instrumental in earthquake monitoring, prediction, early warning, emergency commanding and communication, search and rescue, and life detection. There are numerous sensors currently being utilized in earthquake engineering and science. It is essential to review their mechanisms and working principles thoroughly. Hence, we have attempted to review the development and application of these sensors by classifying them based on the timeline of earthquakes, physical or chemical mechanisms of sensors, and location of sensor platforms. In this study, we analyzed all available sensor platforms that have been widely used in recent years, with satellites and UAVs being among the most used. The findings of our study will be useful for future earthquake response and relief efforts, as well as research aimed at reducing earthquake disaster risks.

Environmental monitoring is an important topic and serves a vibrant scientific role by revealing long-term trends that can lead to new knowledge and understanding. Globally, there is active development of photonic sensors incorporating multidisciplinary research. The ultimate objective is to develop small, low-cost, sensitive, selective, quick, durable, remote-controllable sensors that are resistant to electromagnetic interference. Different photonic sensor designs and advances in photonic frameworks have shown the possibility to realize these capabilities. In this review paper, the latest developments in the field of optical waveguide and fiber-based sensors which can serve for environmental monitoring are discussed. Several important topics such as toxic gas, water quality, indoor environment, and natural disaster monitoring are reviewed.