This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

In 2023, the Bureau of Land Management (BLM) estimated that there were 68,928 mustangs living on United States public lands in 10 western states. The agency uses Appropriate Management Levels to determine the number of mustangs who need to be removed from the land. Once removed and processed, mustangs are sent to adoptions or sales events or retained in short-or long-term holding facilities. Adoptions and sales are the leading avenues for rehoming mustangs; however, the number of horses the BLM can place fluctuates annually and never approaches the greater number removed from the range. To explore opportunities for increasing the number of mustang adoptions, we conducted in-depth interviews with 23 horse trainers located on the U.S. East Coast, asking about participants’ training programs, relationships with horses, perceptions of mustangs, and challenges that mustangs face in the dressage and eventing industries. Participants had varying experiences with mustangs; however, all were willing to work with a mustang in some capacity. Participants voiced the need for more satellite adoption locations on the East Coast to decrease barriers to acquiring a mustang, notably cost and time, and for expanding existing training programs to include eventing and dressage.

As a precious natural resource, forests are being destroyed. In previous studies, there is a lack of interactive assessment of its distribution that comprehensively considers multiple external disturbances. This paper takes the Barcelona Metropolitan Region as an example. Based on remote sensing, it analyzes the development process of the forest from 2006 to 2018 through multiple landscape indicators, and OLS models were established to analyze variables that have direct and indirect effects on forest distribution. In addition, the ecological structure of the forest was analyzed based on NDVI. It was found that the forest area is the largest but has been decreasing, becoming more complex in distribution structure. Much of the forest was converted to agricultural land and grassland. The green quality of forests was increasing, and the broad-leaved forest, the second largest area, contributes the most. NDVI is the most important positively correlated variable, and daytime surface temperature is an important inverse factor related to NDVI. In addition, NDBI is also a negative condition that inhibits forest development. In conclusion: The BMR forest area is decreasing and becoming more fragmented. NDVI and daytime LST are the two most significant factors. Climate warming may lead to worse forest development.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Brazil has ideal conditions for the large-scale use of cabotage cargo transportation: a vast coastline with almost 7,400 km, approximately 70% of the population resident in a coastal range of up to 200 km from the coast and a strong concentration of activities economic along the coast. However, there is an absolute domain of road modal for the transportation of goods, and cabotage is underused. The purpose of the study was to raise the main barriers that negatively impact the performance of Brazilian cabotage. To this end, it was used to bibliographic and documentary research, based on studies already published in journals, doctoral theses, master's dissertations, congress annals, technical reports and research on government-related government agencies sites, navigation companies and entities related to cabotage. The main barriers that contribute to the low use of cabotage in Brazil were identified and analyzed, as well as possible alternatives of solution for sustainable development of this mode of transport. Such a study will certainly serve as subsidies for the definition of public policies aimed at better use of Brazilian cabotage, as well as to encourage navigation companies to invest more in the transport of goods by cabotage, in order to contribute to the reduction of trucks on highways Brazilian and for environmental preservation.

“De-[Constructing] Growth” is offered as a deeper and more useful conceptualization that avoids the negative connotations of, and resistance to, “degrowth” by decoupling profit from unsustainable consumption, production, and inequality.

Background/Objectives: Concurrent opioid (OPI) and benzodiazepine (BZD) use may exacerbate falls/fractures risk compared to no use or use alone. Yet, patients may need concurrent OPI-BZD use for co-occurring conditions (e.g., pain and anxiety). Therefore, we examined the association between longitudinal OPI-BZD dosing patterns and subsequent injurious falls risk. Methods: We conducted a retrospective cohort study including non-cancer fee-for-service Medicare beneficiaries initiating OPI and/or BZD in 2016-2018. We identified OPI-BZD use patterns during the 3 months following OPI and/or BZD initiation (i.e., trajectory period) using group-based multi-trajectory models. We estimated time to first injurious fall within 3 months post-trajectory period using inverse-probability-of-treatment-weighted Cox proportional hazards models. Results: Among 622,588 beneficiaries (age≥65=84.6%, female=58.1%, White=82.7%; having injurious falls=0.45%), we identified 13 distinct OPI-BZD trajectories: Group(A):Very-low OPI-only (early discontinuation)(44.9% of the cohort); (B):Low OPI-only (rapid decline)(15.1%); (C):Very-low OPI-only (late discontinuation)(7.7%); (D):Low OPI-only (gradual decline)(4.0%); (E):Moderate OPI-only (rapid decline)(2.3%); (F):Very-low BZD-only (late discontinuation)(11.5%); (G):Low BZD-only (rapid decline)(4.5%); (H):Low BZD-only (stable) (3.1%); (I):Moderate BZD-only (gradual decline)(2.1%); (J):Very-low OPI (rapid decline)/Very-low BZD (late discontinuation)(2.9%); (K):Very-low OPI (rapid decline)/Very-low BZD (increasing)(0.9%); (L):Very-low OPI (stable)/Low BZD (stable)(0.6%); and (M):Low OPI (gradual decline)/Low BZD (gradual decline)(0.6%). Compared with Group(A), 6 trajectories had increased 3-month injurious fall risks: (C): HR, 95%CI=1.78, 1.58-2.01; (D): 2.24, 1.93-2.59; (E): 2.60, 2.18-3.09; (H): 2.02, 1.70-2.40; (L): 2.73, 1.98-3.76; and (M): 1.96, 1.32-2.91. Conclusions: Our findings suggest that 3-month injurious fall risk varied across OPI-BZD trajectories, highlighting the importance of considering both dose and duration when assessing fall risks of OPI-BZD use among older adults.

Large-scale hydrological modeling in China is challenging given the sparse meteorological stations and large uncertainties associated with atmospheric forcing data.Here we introduce the development and use of the China Meteorological Assimilation Driving Datasets for the SWAT model (CMADS) in the Heihe River Basin(HRB) for improving hydrologic modeling, by leveraging the datasets from the China Meteorological Administration Land Data Assimilation System (CLDAS)(including climate data from nearly 40000 area encryption stations, 2700 national automatic weather stations, FengYun (FY) 2 satellite and radar stations). CMADS uses the Space Time Multiscale Analysis System (STMAS) to fuse data based on ECWMF ambient field and ensure data accuracy. In addition, compared with CLDAS, CMADS includes relative humidity and climate data of varied resolutions to drive hydrological models such as the Soil and Water Assessment Tool (SWAT) model. Here, we compared climate data from CMADS, Climate Forecast System Reanalysis (CFSR) and traditional weather station (TWS) climate forcing data and evaluatedtheir applicability for driving large scale hydrologic modeling with SWAT. In general, CMADS has higher accuracy than CFRS when evaluated against observations at TWS; CMADS also provides spatially continuous climate field to drive distributed hydrologic models, which is an important advantage over TWS climate data, particular in regions with sparse weather stations. Therefore, SWAT model simulations driven with CMADS and TWS achieved similar performances in terms of monthly and daily stream flow simulations, and both of them outperformed CFRS. For example, for the three hydrological stations (Ying Luoxia, Qilian Mountain, and ZhaMasheke) in the HRB at the monthly and daily Nash-Sutcliffe efficiency ranges of 0.75-0.95 and 0.58-0.78, respectively, which are much higher than corresponding efficiency statistics achieved with CFSR (monthly: 0.32-0.49 and daily: 0.26 – 0.45). The CMADS dataset is available free of charge and is expected to a valuable addition to the existing climate reanalysis datasets for deriving distributed hydrologic modeling in China and other countries in East Asia.

One of today’s most critical challenges is ensuring a sufficient food production and supply for the ever-expanding global population. Recently, many countries around the world, particularly those in Africa, grapple with severe hunger and food insecurity, frequently exacerbated by escalating global prices, persistent insecurity, and the repercussion of the COVID-19 pandemic. However, this study undertook an extensive review of the prevalence and severity of hunger and food insecurity across diverse countries and regions. The review utilised several metrics, including Global Hunger Index (GHI) scores, Global Food Security index (GFSI) scores, 2023 data (related to two Sustainable Development Goal 2 (SDG2) target) from the Food and Agriculture Organization (FAO), and other pertinent sources to assess the current status of the countries included in this study. The 20 countries with 2023 GHI scores below 5 were collectively ranked from 1 to 20, signifying low hunger levels. However, Central African Republic (CAR) received the lowest ranking at 125 out of 125, with a score of 42.3, indicating an alarming level of hunger. Finland achieved the highest GFSI score of 83.7, with Oman showing the most notable GFSI improvement at +13.8, while Syria experienced a significant decline in GFSI score by -10.5. Over time, many countries, particularly the developed ones, witnessed significant improvement in their GHI and GFSI scores. Meanwhile, most countries in sub-Saharan Africa experienced the most deterioration in their GFSI scores and notable increases in their GHI scores. The review documented the significant progress made by countries and regions in reducing levels of hunger and food insecurity, while highlighting the substantial burden borne by sub-Saharan Africa (SSA) in combating global hunger and food insecurity.

Peanut hulls (PH) are an edible food waste that is an underutilized food source for human consumption. While edible and palatable, they are mainly diverted to livestock feed or building materials. Here, we describe existing literature on human food valorization of PHs and propose methods to optimize recapturing nutrients (e.g. protein, fiber, polyphenols) lost by treating PHs as waste. Incorporated into common foods, PHs can be processed into functional ingredients to improve nutrient-density and the corresponding positive health outcomes associated with increases in plant foods. PH valorization can also address additional priorities of the UN Sustainable Development Goals using a Food Systems Approach (FSA) including food waste, increasing economic opportunities for farmers, and increasing the availability of healthy shelf-stable foodstuffs to address food security. Recent advances in sustainable food processing technologies can be utilized to safely incorporate peanut hulls into human food streams. We propose future applications that could make meaningful impacts to food availability and the nutritional composition of common foods. While the limited literature on this topic spans several decades, no global operations exist to incorporate peanut hulls and most publications precede the technological ‘green revolution’. The approaches outlined in this review may help bolster commercialization of this underutilized and nutritious food potentially improving opportunities for multiple global stakeholders.

The Asian clam Corbicula fluminea is a native aquatic species in Eastern Asia and Africa but has become one of the most ecologically and economically harmful invasive species in aquatic ecosystems in Europe, North America, South America. Due to their natural characteristics as a hermaphroditic species with high fecundity and dispersal capacity, Asian clams are extremely difficult to eradicate once they have infiltrated a waterbody. This is an emerging issue for states in the Northeastern United States as Asian clams expand their range farther North due to climate change. There has been extensive research conducted to develop chemical treatments to reactively control invasive mollusc populations and proactively prevent their further spread. However, treatments are mostly targeted toward biofouling bivalves in industrial settings. A comprehensive review of Asian clam chemical treatments used in open water systems was performed to evaluate molluscicides and identify toxicity ranges of emerging treatments that maximize Asian clam mortality and minimize negative impact to water quality and non-target species. The potential chemical applications in Asian clam control and management are summarized in this report to assist resource managers and practitioners on invasive Asian clam management.

Cybersecurity is a crucial concern for local governments, as they serve as the primary interface between public and government services, managing sensitive data and critical infrastructure. While technical safeguards are integral to cybersecurity, the role of well-structured policy is equally important, as it provides structured guidance to translate technical requirements into actionable protocols. This study reviews local governments’ cybersecurity policies to provide a comprehensive assessment of how these policies align with NIST CSF, which is a widely adopted and commonly used cybersecurity assessment framework. The review offers local governments a mirror to reflect on their cybersecurity stance, identifying potential vulnerabilities and areas needing urgent attention. The study further extends to developing a cybersecurity policy framework, which local governments can use as a strategic tool. It provides valuable information on crucial cybersecurity elements that local governments must incorporate into their policies to protect confidential data and critical infrastructure.

(1) Background: in the context of sustainable development goals (SDGs), this work explores the repair direction of future cultivated land protection policies based on the Smith policy implementation model from the historical evolution to ensure that the cultivated land protection policy does not deviate during the implementation process. (2) Methods: this paper uses literature research and inductive deduction methods to sort out the evolution process of Chinese cultivated land protection policy, summarize the successful experience of transferring the focus of cultivated land protection in chronological order, and conclude the repair direction of Chinese cultivated land protection. (3) Results: although the Chinese cultivated land protection policy in the historical evolution has through three significant phases, there are still certain issues in the development trend of Chinese cultivated land protection policy based on regional division of labor for grain transportation and sales. (4) Conclusion: directly utilizing feedback from farmers as stakeholders will contribute to the maturity and improvement of cultivated land protection policies in the specific implementation of cultivated land protection policies.

Frailty is a common condition in older adults that negatively impacts health and quality of life. This study evaluated a comprehensive, personalized, and coordinated intervention under the Value-Based Care approach to address frailty's multidimensional nature in older people. It em-ployed a pre-post randomized controlled design, involving frail individuals over 65 years in Valencia, Spain. Assessments were conducted at baseline, 12 months (immediately post-intervention), and 18 months. The intervention included a personalized care plan supported by technology, with monthly motivational follow-ups and plan updates by health professionals and participants. Outcomes were measured using an assessment questionnaire that included the International Consortium for Health Outcomes Measurement dataset for the older population: physical health, physical functioning, general mental health, satisfaction with social activities and relationships, ability to carry out usual social roles and activities, pain, general quality of life, loneliness, physical frailty, psychological frailty and social frailty. The study found signifi-cant improvements in physical frailty, quality of life, reduced health resource use and hospitali-zations, and lower levels of pain and depression/anxiety compared to baseline. The findings suggest further research into value-based care approaches, emphasizing the development and activation of personalized, comprehensive programs for older individuals with frailty.

Crop production in Afghanistan suffers from limited phosphorus (P) availability, which severely hinders national agriculture sustainability. This present study hypothesized that deep fertilizer placement could significantly enhance uptake of immobile P and thus tissue P accumulation and crop yield. A two-year pot experiment growing two maize (Zea mays) hybrid cultivars (Xida-789 and Xida-211) was therefore conducted to test these hypotheses under three contrasting fertilizer placement methods (broadcast, side band, and deep band). In doing so, P concentrations in both maize tissues and soils were compared at 45, 60, and 115 days after sowing (DAS) under nine combinations of nitrogen (N) and P fertilizer rates (kg ha-1: N112P45, N112P60, N112P75, N150P45, N150P60, N150P75, N187P45, N187P60, N187P75). Results have shown that deep band placement significantly increased P uptake efficiency, leading to greater P concentration and accumulation in maize tissues compared to other two fertilization methods. This improved P uptake was attributed to several factors associated with deep placement, including reduced P fixation, enhanced root access to P, and moisture availability for P uptake. Additionally, deep band placement combined with higher N application rates (N187 and N150) further enhanced plant P uptake by promoting P availability and utilization mechanisms. Deep band placement also resulted in significantly higher total soil P, Olsen-P, and P use efficiency than broadcast and side band methods, indicating a more efficient P fertilization strategy for maize that can improve growth and yield. This present study also found positive correlations between P concentration in plant organs and soil Olsen-P, highlighting the importance of adequate soil P levels for optimal plant growth. Overall, our results have showed that deep band fertilizer placement emerged as a superior strategy for enhancing P uptake efficiency, utilization, and maize productivity compared to broadcast and side band placement. This approach can potentially optimize P fertilizer utilization, improve maize growth and yield, while minimizing environmental P losses associated with broadcast applications.

Following the adoption of the Kunming-Montreal Global Biodiversity Framework (KM-GBF), with the Convention on Biological Diversity serving as its guiding treaty, the European Union (EU) has just reached an agreement on an EU Nature Restoration Regulation. This study carries out a systematic cross-walk between the restoration regulation and the KM-GBF, focusing on their implications for forest ecosystems. This paper identifies areas of alignment, divergence, and potential gaps related to habitat restoration, species protection, climate resilience, and the sustainable use of natural resources. The methodology adopts a grounded approach, starting with the 23 targets outlined in the KM-GBF and proceeding to the 28 articles set out in the restoration regulation. The results highlight the need for better alignment between the KM-GBF, the restoration regulation, and other forest-relevant EU policy instruments. The study stresses the need for a coherent and integrated EU policy approach that can address the diverse challenges and policy objectives facing forests. It concludes that amendments to the restoration regulation have significantly diluted its potential impact, limiting the EU Members States accountability and ability to meet KM-GBF goals and targets. It further stresses the need for strategies that can reconcile divergent EU policy pathways, support forest management and restoration efforts, while aligning with global biodiversity objectives.

Conditions under which compositions of component systems form a well-defined system-of-systems here are formulated at a fundamental level. Statement of what defines a well-defined composition and sufficient conditions guaranteeing such a result offers insight into exemplars that can be found in special cases such as differential equation and discrete event systems. For any given global state of a composition, two requirements can be stated informally as: 1) the system can leave this state, i.e., there is at least one trajectory defined that starts from the state, and 2) the trajectory evolves over time without getting stuck at a point in time. Considered for every global state, these conditions determine whether the resultant is a well-defined system and if so, whether it is non-deterministic or deterministic. We formulate these questions within the framework of iterative specifications for mathematical system models that are shown to be behaviorally equivalent to the Discrete Event System Specification (DEVS) formalism. This formalization supports definitions and proofs of the afore-mentioned conditions. Implications are drawn at the fundamental level of existence where the emergence of a system from an assemblage of components can be characterized. We focus on systems with feedback coupling where existence and uniqueness of solutions is problematic.

Dairy farming dates to the early Neolithic era in Europe, Middle East, Asia, and Africa. Over time, the industry has evolved from small ranches and farmhouses milk processing units to large, intensive dairy farms and big, high-tech processing units. Despite the industry’s contribution to the economy and food production, multiple studies have tainted cattle farming as a main contributor to climate change. This study explores literature in dairy farming and sustainable development goals (SDGs) to identify current scholarly developments since the formulation and adoption of SDGs in 2015 and themes for future research. This paper argues that dairy animals are not the source of sustainability shortfalls as depicted by multiple scholarly articles, but human processes associated with dairy farming. Data was analyzed using R package, Excel, NVIVO, and VoS Viewer. A review of literature shows that dairy farming and its contribution to sustainability has gained more intensive scientific interest since 2015. Moreover, livestock management, feed production and management, stakeholder’s management, logistics and supply chain management, and waste management are the sources of environmental adversities associated with dairy farming. Notably, these are human processes developed from commercialization of dairy farming and involve multiple stakeholders across the supply chain. While solutions are embedded within these processes, innovation emerges as a key driver of sustainability and source of opportunities to strengthen sustainability in dairy farming sector and achieve the sustainable development goals.

Despite the known benefits of precision agriculture, the adoption is challenging due to the cost of investment and the farm sizes. Therefore, profitability is an important aspect to consider. This study aimed to evaluate the net returns, profitability, and investment efficiencies of PA by different economic farm sizes. The study was based on data retrieved from FADN and Eurostat. The study examined four countries (Poland, Germany, France, and Romania) under field crop farming using an investment cost of €35 941 - €71 883, and a 20% and 15% reduction in the cost of crop protection and fertilizer usage respectively without compromising productivity. There is a positive relationship between the adoption of PA and farm returns for larger-scale farms. The result of the profitability and analysis of investment efficiency using NPV showed a positive value for economic farm sizes of €100 000 and above. Hence, it is not economically advisable that all farmers use PA technologies with the hope that they will be profitable but with public support (subsidies) more farms will be able to use PA and be profitable. Also, an opportunity to meet the goal of the European Union Green Deal of minimizing emissions that cause climate change.

There are many uncertainties and risks in residential electricity consumption during the economic development. Knowledge of the relationship between residential electricity consumption and its key determinant—income—are important to the sustainable development of electric power industry. Using panel data from 30 provinces for the 1995-2012 period, this study investigates how residential electricity consumption changes as incomes increase in China. Previous studies typically used linear or quadratic double-logarithmic models imposing ex ante restrictions on the indistinct relationship between residential electricity consumption and income. Contrary to those models, we employed a reduced piecewise linear model that is self-adaptive and highly flexible and circumvents the problem of “prior restrictions.” Robust tests of different segment specifications and regression methods are performed to ensure the conservatism of the research. The results provide strong evidence that the income elasticity was approximately one, and it remained stable throughout the estimation period. The income threshold at which residential electricity consumption automatically remains stable or slows has not been reached. To ensure the sustainable development of the electric power industry, introducing higher energy efficiency standards for electrical appliances and improving income levels are vital. And government should emphasize electricity conservation in industrial sector rather than in residential sector.

The goal of farmers operating in a market economy is to maximise profit. In the face of the changing political situation, the main social interest, besides food security, should be energy security. This article aims to indicate the direction of agricultural policy development so that it guarantees both the economic security of producers—farmers—and Europe’s energy security. The work uses data obtained from the agri benchmark Cash Crop database. DEA method and stepwise multiple regression were used. The research showed that plants are already grown in Europe which will ensure high energy efficiency of production without compromising farm financial results (including oats, peas and winter rye) and that improving the involvement of certain inputs results in improved production efficiency (among others, by expenditure on agricultural advisory services). The significance of the presented research results from the fact that the recent COVID pandemic and escalation of the military conflict in Ukraine have led to a renewed interest in the concept of EU energy security, i.e. generation of generating the greatest possible amount of energy within the EU, to be used both for food and non-food purposes.

Given the opportunities offered by foreign investment in energy infrastructure mostly by Chinese firms, the Government of Cambodia is giving high priority to developing hydropower resources for reducing energy poverty and powering economic growth. Using a “Political ecology of the Asian drivers” framework, this paper assesses China’s involvement in the development of large dams’ in Cambodia and its impacts on the access of natural resources such as water and energy by dam builders, local communities and the government. This analysis is based on 61 interviews and 10 focus group discussions with affected communities, institutional actors, Chinese dam builders and financiers in relation to the first large Chinese dam built in Cambodia, the Kamchay dam. Based on the results of the analysis this paper makes recommendations on how to improve the planning, implementation and governance of large dams to ensure that the dams’ benefits are shared more equally.

Using numerical simulation method, combined with the pre-branch material characteristics of the measurement results, based on the LS-DYNA software to simulate the branch crushing process, the analysis found that not only the existence of the cutter cutting in the branch destruction process, there is also the cutting of the opposing surface of the bending fracture, with the increase in the speed of the knife rollers, the cutter cutting resistance increases, the cutting resistance reaches 2690 N when the cutter at 2500 r/min, the cutter cutting resistance is the smallest in the cutting simulation at the blade angle of 55°, the blade angle is more suitable for the cutting of the branch. In the cutting simulation under different cutting edge angles, the cutting resistance of the tool is the smallest when the edge angle is 55°, which is 1860 N. This edge angle is more suitable for branch crushing and cutting. Using Fluent software to analyse the airflow characteristics of the crushing device, it was found that with the increase of the knife roller speed, the inlet flow and negative pressure of the crushing chamber are increasing, the speed of 2500 r/min, the inlet flow and negative pressure were 1.92 kg/s and 37.16 Pa, which will be conducive to the feeding of branches, but the speed is too high and it will also lead to the enhancement of the vortex of part of the area in the crushing device, which will affect the feeding of branches and the throwing of the crushed material. affect the feeding of branches and the throwing out of crushed materials, and finally determined the speed range of the crushing knife roller is 1800 ~ 2220 r/min. Based on ANSYS/Model module modal analysis of the crushing knife roller, the knife roller of the first six orders of the intrinsic frequency and vibration pattern, crushing knife roller of the lowest order of the modal intrinsic frequency of 137.42 Hz, much larger than the crushing knife roller operating frequency of 37 Hz, the machine will not resonate during operation.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

This paper, from the perspective of Mode 3 of knowledge production, takes the important carrier of knowledge, scientific research papers, as the research object. The mainstream databases (SCIE and SSCI) are chosen as the data sources. Firstly, bibliometric methods are applied to analyze the cooperation status among the main bodies of paper production, including authors and their affiliated institutions, countries, and disciplines; secondly, the Analytic Hierarchy Process (AHP) is used to construct a comprehensive evaluation model for the state of research cooperation in carbon neutrality. Based on the evaluation model, the cooperation characteristics of different disciplinary fields and the relationship between paper cooperation status and high-impact research papers are comparatively analyzed. At the same time, an analysis is conducted on the support from the government, the sponsorship from enterprises, and the participation of the public in the process of paper production. Finally, some suggestions are put forward on how to build an innovative ecosystem for carbon neutrality research from the perspective of Mode 3 of knowledge production.

In recent years, Nigeria is witnessing increasing frequency of flood occurrence with devastating impact translating into significant loss of lives (in Nigeria, over 300 people died in September 2022) and properties. Addressing flood disaster requires holistic approach from policy and governance perspectives, integration of policies and programs and synergies between institutions. Using synergies and eliminating trade-offs, flood governance and policy coherence integrate all relevant policy fields and institutions to achieve common policy outcomes. The objective of this study is to examine and understand how flood governance and policy coherence are approached, as well as institutional design and implementation for coherence in Nigeria. The findings revealed that there is no single flood policy in Nigeria. Due to this, there is no focus and no defined objectives for flood governance, prevention, control, and management, and no imperative for the government to seek both short-term and long-term flood solutions. There is no synergy and coordination among institutions for flood governance in the country. Since the country established the federal ministry of environment in 1999, the environment, floods, and climate-related hazards were given less priority. State and local governments handle most flood disasters and emergencies. Federal assistance is provided, however, when flood disasters exceed the capabilities of local and state governments. This study recommends that across the country, flood policy needs to be designed, formulated, and implemented while assigning governance responsibility and decentralizing policy to state and local governments.

This paper presents the development of a prescriptive digital twin model designed to optimize building environments by leveraging advanced smart technologies such as machine learning, artificial intelligence, cloud computing, and the Internet of Things. The study identifies critical factors affecting user activities, including lighting, HVAC, indoor air quality, and acoustics, and incorporates these into the model to enhance user productivity and comfort in workspaces. Our findings demonstrate that the integration of smart technologies can significantly improve workspace efficiency and user satisfaction, providing actionable insights for future implementations. This study not only highlights the potential benefits of prescriptive digital twins in smart buildings but also emphasizes the importance of comprehensive data gathering and analysis from various sources to support further research. Ultimately, our work offers valuable contributions to the field of building management and underscores the need for continued exploration of digital twin technologies.

This research aimed to investigate the relationship between climate policy uncertainty (CPU), clean energy (ENERGY), carbon emission allowance prices (CARBON), and Bitcoin returns (BTC) for the period from August 2012 to August 2022. The empirical analysis strategies utilized in this study included the Fourier Bootstrap ARDL long-term coefficient estimator, Fourier Granger Causality, and Fourier Toda Yamamoto Causality methods. Following the confirmation of cointegration among the variables, we observed a positive relationship between BTC and CARBON, a positive relationship between BTC and CPU, and a negative relationship between BTC and ENERGY. In terms of causal associations, we identified one-way causality running from CARBON to BTC, BTC to CPU, and BTC to the ENERGY variable. The study underscores the potential benefits and revenue opportunities for investors seeking diversified investment strategies in light of climate change concerns. Furthermore, it suggests actionable strategies for policymakers, such as implementing carbon taxes and educational campaigns, to foster a transition towards clean energy sources within the cryptocurrency mining sector and thereby mitigate environmental impacts.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

Abstract: Efforts for carbon emission reduction have been identified as a major climate change mitigation target in the Paris Agreement. The 26th Conference of Parties to the United Nations Framework Convention on Climate Change highlighted the worldwide effort for cleaner and greener mining, urging the mineral industry to embrace greener operational emissions reduction technologies and strategies. Ghana pledged at the Paris Conference to reduce CO2 emissions by 15% and increase renewable energy share to 10% of the national energy mix. Here the fundamental question is how Ghana’s mining industry can contribute to CO2 emission reduction efforts. This paper investigates barriers to low-carbon emission policy implementation among mining companies in Ghana. The questionnaire survey was conducted among Ghana’s four large-scale gold mining companies. As the sample number of available companies is limited, we used a descriptive analysis to assess the responses. The results show that the companies expressed widely different ways to respond to the issues of cost, a government policy/regulations for carbon emission reduction, and the adoption/acquisition of low-carbon technologies. Those companies that are relatively less prepared for this endeavor emphasized the uncertainties of securing sufficient energy in case of using low-carbon technologies. They also expressed a need for more trained workers to handle low-carbon technologies. All companies agreed with a expected high cost of adopting low-carbon options. There was a communication gap with the relevant government ministry about low-carbon mining options where the government should be able to facilitate the involvement of othe low technology providers, such as solar PV installation.

Although promoting healthy eating is a policy objective, the controllability of dietary habits remains uncertain. The personal dietary patterns reflect many factors, of which some are relatively controllable for individual, and others are not. In this article, assuming that some sort of information about controllability of dietary habits is contained in the observed pattern of food consumptions, we focused on dietary pattern on its own. We introduced a statistical descriptive model for data on food frequency questionnaire, estimated strength of pairwise linkage between foodstuffs, and grouped foodstuffs by applying community detection to the networks of the estimated inter-food linkages. Those linkages represent co-movement of pairs of foods consumption. Furthermore, we demonstrated an analysis on the relationship between health of mind and dietary habits considering the aspect of controllability of dietary habits. Using an observational study in Japan, we obtained the following results: 115 foodstuffs were divided into 3 groups for both of genders, but the compositions were different by gender; in the analysis of mental health, some stress response items were associated with the dependence on some of those food groupings. As the grouping of foodstuffs based on our estimation depicted the internal structure of dietary habit that a healthy eating policy should regard as constraint, it follows that we should design the policy along the line with that grouping.

The development of virtual models has recently been generalized in the field of complex mechatronic product design. Virtual models have various advantages such as: the systemic design approach, most often parametric, the implementation of extreme, expensive, and perhaps risky scenarios for the operation of the designed product, the testing of a large number of variants, etc. The main contribution of the paper consists of the development of an interface family called DeSeRoI (Dedicated Serial Robot Interface). Each member of the interface family integrates Simulink libraries and is created by the programmer in accordance with user requests. It follows that the interfaces composing the DeSeRoI family can have different levels of complexity depending on user needs and constraints. We are implementing a MATLAB-based application with user-provided configuration for serial robots in order to automatically visualize the kinematics data and simulation. Within MATLAB, two scripts are created responsible for generating Simulink models that compute the kinematics problem. One of the scripts (Main) saves information about the configuration of the robot and the other one (Generates_Simulink_Models) computes the kinematics problem. Different types of functions (software module) have been developed. Using these functions, the Simulink models result as modular entities. The automated approach eases user’s interaction and understanding of serial robots’ kinematics by performing the simulation procedure in a shorter amount of time and with higher efficiency, assuring a precise outcome despite the chosen parameters.

This study examines geothermal energy extraction potential from the basement rock within the Denver-Julesburg (DJ) Basin, focusing on flow performance and heat extraction efficiency of different geothermal well configurations. It specifically compares U-Shaped, V-Shaped, Inclined V-Shaped, and Pipe-in-Pipe configurations against Enhanced Geothermal Systems (EGS) setups. Through numerical modeling, we evaluated the thermal behavior of these systems under various operational scenarios and fracture conditions. Results suggest that while closed-loop systems offer moderate temperature increases, EGS configurations show substantial potential for high-temperature extraction. This underscores the importance of evaluating well configurations in complex geological settings like the DJ Basin. The insights from this study aid in strategic geothermal energy planning and development, marking significant advancements in geothermal technology and setting a foundation for future explorations and optimizations.

China’s leading development of a complete battery value chain for Electric Vehicles (EV) is restructuring the global automotive sector. The competitive advantage of China's EV battery industry lies on its firms’ core competency and political economic geography. Based on first-hand empirical material and data obtained from years of fieldwork in an EV battery cluster in South China, this paper identifies what the Chinese EV battery industry’s core competency is and details how it is built up from below. The current core competency of Chinese battery firms is their mass manufacturing capability to supply lithium-ion batteries vehicle manufacturers (OEMs) with stable and consistent quality as well as competitive prices. This competency is acquired by firms through technological learning at workshop level while taking use of their experiences accumulated in mass production of batteries for consumer electronics sectors. Furthermore, the rapid learning and accumulation of knowledge on battery manufacturing at large scale is also facilitated by the industrial cluster environment where firms are embedded. Supported and promoted by local government policies, Chinese EV battery clusters are composed of firms from different segments of a complete battery value chain. The findings illuminate the likely strategic strengths, weaknesses, and futures of the Chinese EV battery industry in global competition.

This article seeks to provide an improved and more comprehensive understanding of the concept and theories on wasteland. It achieves this by focusing on the Indian context allowing us to unpack the importance of including multiple perspectives of wasteland narratives; this means including more positive narratives of the potential of wasteland to inform and improve prospects for land policies in the global south. Wasteland is commonly recognized as an underutilized category of land that may transform into a valuable resource base with proper management measures. The term waste has multiple angles that carry different notions ranging from fallow to agroforestry land in the global south and Brownfield to green space in the global north. We conduct a narra-tive review approach to qualitatively analyze the concept wastelands studied in pre-existing lit-erature from 1970 to present. The unsystematic literature review approach incorporates multiple elements of wasteland discourse, like understanding the meaning of the term on a global scale, setting out the meaning of the term waste into multiple perspectives explicitly in the Indian con-text, along with different classes and management approaches of wasteland from a national per-spective. The multiple perspectives of wasteland not only generate misconception on land resource but spawn difficulties in land use policy particularly for Indian scenario. For sustainable land use policy, reclaiming wasteland would be the best possible way for India and other countries in Global South, which requires a comprehensive methodological overview on wasteland narrative.

Driven by the growing interest of the scientific community and the proliferation of research in this field, cranial implants have seen significant advancements in recent years regarding design techniques, structural optimisation, appropriate material selection and fixation system method. Custom implants not only enhance aesthetics and functionality but are also crucial for achieving proper biological integration and optimal blood irrigation, critical aspects in bone regeneration and tissue health. This research aims to optimize the properties of implants designed from triply periodic minimal surface structures. The gyroid architecture is employed for its balance between mechanical and biological properties. Experimental samples were designed varying three parameters of the surface model: cell size, isovalue and shape factor. Computational simulation tools were used for determining the relationship between those parameters and the response variables: the surface area, permeability, porosity and Young modulus. These tools include computer aided design, finite element method and computational fluid dynamics. With the simulated values, the corresponding regression models were fitted. Using the NSGA-II, a multi-objective optimisation was carried out, finding the Pareto set which includes surface area and permeability as targets, and fulfil the constraints related with the porosity and Young modulus. From these non-dominated solutions, the most convenient for a given application was chosen, and an optimal implant was designed, from a patient computed tomography scan. An implant prototype was additively manufactured for validating the proposed approach.

While the foundations of climate science and ethics are well established, fine-grained climate predictions, as well as policy-decisions, are beset with uncertainties. This chapter maps climate uncertainties and classifies them as to their ground, extent and location. A typology of uncertainty is presented, centered along the axes of scientific and moral uncertainty. This typology is illustrated with paradigmatic examples of uncertainty in climate science, climate ethics and climate economics. Subsequently, the chapter discusses the IPCC’s preferred way of representing uncertainties and evaluates its strengths and weaknesses from a risk management perspective. Three general strategies for decision-makers to cope with climate uncertainty are outlined, the usefulness of which largely depends on whether or not decision-makers find themselves in a context of deep uncertainty. The chapter concludes by offering two recommendations to ease the work of policymakers, faced with the various uncertainties engrained in climate discourse.

As the leader of the largest economy, President of the United States has substantive influence on addressing the global climate change problem. However, presidential election is often dominated by issues other than energy problems. This paper focuses on the on-going 2016 presidential election, examining the energy plans proposed by the leading Democrat and Republican candidates. Our data from the Iowa caucus survey in January 2016 suggests that voters are more concerned about terrorism and economic issues than environmental relative issues. We then compare the Democratic and Republican candidate’s view of American’s energy future, and evaluate their proposed renewable energy targets. We find that the view on renewable energy is polarized between Democratic and Republican candidates, while candidates from both parties agree on the need for energy efficiency. Results from our ordinal least squares regression models suggest that Democratic candidates have moderate to ambitious goals for developing solar and other renewable energy. The Republican candidates favor fossil fuel and they neglect to provide any plan for renewable energy. In addition, this trend of polarization has grown more significant when compared with the past three presidential elections. Our observation suggests that energy issues need to be discussed more to draw broader attention to salient issues of diversifying and decarbonizing the nation’s energy system.

Older adults with obesity have an increased risk for cognitive decline and subsequent Alzheimer’s disease. Previous research has focused on the impact of individual nutrients and overall dietary patterns to improve cognitive function. The Brain and Body Health (BB-Health) study aims to demonstrate the feasibility of a multicomponent nutritional supplement (MCNS) and weight loss (WL) intervention for individuals with overweight and obesity who are not consuming a healthy diet. BB-Health is a parallel-group randomized placebo-controlled 2x2 factorial pilot trial comparing the MCNS, WL, and MCNS+WL with a Control group. Eligible participants are 55 to 85 years of age with a body mass index 27.0 to 39.9 kg/m2. Major exclusion criteria include type 2 diabetes, moderate or severe cognitive impairment, and self-reported healthy dietary pattern. The BB-Health feasibility trial is registered as NCT05542199 at clinicaltrials.gov. The BB-Health objectives are to report: 1) recruitment and enrollment, including pace and descriptive statistics of the study sample; 2) adherence to the administered interventions; 3) successful data collection and performance of outcome assessments, including evaluation of change in key outcomes over time that are powered for this pilot study; and 4) summary statistics on outcomes for use in planning a subsequent, larger trial. The outcomes of interest are age-sensitive cognitive assessments, cerebral hemodynamics, and related health parameters. All measurements are collected at baseline, 3-, 6-, and 12-month visits. If the BB-Health protocol demonstrates feasibility, the novel MCNS with and without a parallel WL intervention has potential to be administered in a confirmatory randomized trial to evaluate ability to prevent age-related cognitive decline and improve brain health. The BB-Health Feasibility Study could significantly contribute to our understanding of the influence of diet and weight management on cognitive health

European strategic policy directions towards a sustainable blue economy have strengthened interest in maritime investments, thus increasing sectoral competition for marine space. Emerging repercussions out of such a rising interest need to be handled by Marine Spatial Planning (MSP) as a means for: properly allocating marine space to diverse uses; managing conflicts and promoting synergies among them; and pursuing a multi-use perspective of this space. A critical stage of each MSP exercise is the exploration of land-based spatial/developmental directions and their current or potential repercussions in the marine environment in order for constraints but also perspectives in policy choices/maritime uses in the MSP context to be featured; and attainment of a successful coherence or coordination between land and marine spatial/developmental policies to be ensured, by analyzing Land-Sea-Interaction (LSI) and embedding it in the MSP. The latter is the focus of this paper aiming to illuminate critical issues emerging from land-based (terrestrial) policy frameworks for feeding MSP endeavors; and is accomplished in the Northern Aegean Sea, Greece. Towards this end, a multilevel approach is adopted, delving into diverse policy contexts at the local, regional and national/European level and aiming to attain more informed MSP decisions in the specific study region.

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

The majority of existing numerical simulations of the effect of bridge piers on water movement are based on a limited number of bridge piers at a laboratory scale. Furthermore, some 2D numerical simulations for actual bridge projects have deficiencies, including the use of overly large mesh sizes and an inadequate treatment of bridge piers. In this study, we compare three methods of structural mesh encryption, suspension mesh, and nonstructural mesh based on Delft3D, and apply the optimization scheme to a real bridge project. It is demonstrated that optimal results can be achieved by utilising a grid size comparable to the pier diameter (Dp) in the region away from the piers. In the vicinity of the piers, the grid cell size should be no larger than 1/9 Dp. The suspended grid technique (DD Boundary) can yield results consistent with those obtained using a full-area high-resolution grid, provided that the total number of grids can be reduced and the computational time is considerably reduced. In this study, the unstructured mesh (Deflt3D Flexible Mesh) scheme was unable to capture the oscillations of the wake flow behind the bridge piers. However, the application of the optimized scheme in bridge engineering has demonstrated its practical value. The findings of this study on mesh resolution and suspension mesh scheme can be applied to the Delft3D software and are also useful for other numerical simulation work.

In this paper we report a new development on the numerical model for aluminum-steam combustion. This model is based on diffusion flame of continuum regime and the thermal equilibrium between the particle and the flow field, which can be used to calculate the aluminum particle combustion model for two phase calculation conditions. The model prediction is in good agreement with the experimental data. A new type of vortex combustor was proposed for the combustion of aluminum and steam, and the mathematical model of the two phase reacting flow with in this combustor was established. The turbulence effects are modeled using the Reynolds Stress Model (RSM) with Linear Pressure-Strain approach, and the Eddy-Dissipation model is used to simulate the gas phase combustion. Aluminum particles are injected into the vortex combustor and form a swirling flow around the chamber and their trajectories are traced using the Discrete Phase Model (DPM). The simulation results show that the vortex combustor can achieve high efficient combustion of aluminum and steam. The influencing factors, such as the eccentric distance of the inlet of aluminum particles, particle size and steam inlet diameter, etc., are studied. The work described in this paper represents an attempt to the design of a vortex combustor in order to increase aluminum combustion efficiency.

The control of the fine particle emission from the coal-fired power plants has been a big challenge in china. Either the conventional electrostatic precipitator or the fabric filter has some shortages. The electrostatic precipitator is hard to keep high efficiency for the submicron particles. The fabric filter could keep high efficiency but with very high pressure drop. One solution is to combine them together. Several types of hybrid particle collectors (HPC) combining the electrostatic precipitator and the fabric filter together have been developed and applied in a number of projects in China. In recent years, numerical simulation technology has been widely used in the design of the collectors. In this paper, an unsteady numerical model is used to investigate the particle deposition characteristics in a scale hybrid collector. The fluid field is modeled by using incompressible Navier-Stokes equations with the RNG turbulence equations. The corona discharge is solved by using a finite volume method. The particle charging is modeled by using a filed-diffusing combined model. And an unsteady cake formation model is used to simulate the filtration process.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

The article discusses how tourism policy has changed since World War II, highlighting how the everchanging political and economic climate has shaped policies that were formerly centered on promoting inbound travel and tourist growth to becoming more inclusive and sustainable. Within that framework, the paper systematically examines the development of Indian tourism policy and thoroughly explores the implications of its most recent version. It concludes that modern tourism policies have evolved into comprehensive frameworks that structure the growth of the industry and make it more inclusive and sustainable. Nations such as India are well-suited to meet the demands of modern tourism and offer appropriate frameworks for sustainable and resilient tourist growth.

Retiring coal power plants can reduce air pollution and health damages. However, the spatial distribution of those impacts remains unclear due to complex power system adjustments and pollution chemistry and transport. Focusing on coal retirements in Pennsylvania (PA), we analyze six counterfactual scenarios for 2019 that differ in retirement targets (e.g., reducing 50% of coal-based installed capacity vs. generation) and priorities (e.g., closing plants with higher cost, closer to Environmental Justice Areas, or with higher CO₂ emissions). Using a power system model of the PJM Interconnection, we find that coal retirements in PA shift power generation across PA and the Rest of PJM region leading to scenario-varying changes in the plant-level release of several air pollutants. Due to air pollution chemistry and transport and socio-demographics, these changes in turn give rise to a reduction of 10 to 182 PM_2.5-attributable deaths in PJM across the six scenarios, with most reductions occurring in PA. Scenarios that reduce more coal power generation yield greater aggregate health benefits due to air quality improvements in PA and adjacent downwind regions. In addition, vulnerable populations—in both PA and Rest of PJM—benefit most in scenarios that prioritize plant closures in PA near Environmental Justice Areas. These results demonstrate the importance of considering cross-regional linkages and socio-demographics in designing equitable retirement strategies.

Understanding the dynamics of land use and land cover (LULC) change in today's context of rapid urbanization is critical for sustainable urban planning and environmental conservation. Therefore, the research aim is to understand the LULC changes in Chattogram Metropolitan Area and to assess the policy implications of these changes for sustainable urban development. Through a comparative analysis of LULC maps for two periods (1997–2007; 2007–2017), we investigated the transformation of a detailed planning zone before and after detailed area plan (DAP) approval. Using a mixed-method approach integrating quantitative data with policy analysis, we elucidated the impacts of urbanization trends on local ecosystems—specifically the conversion of forest cover and waterscape use. The findings reveal a significant conversion of forested and waterscape areas to urban and peri-urban landscapes, highlighting the urgent need for sustainable planning interventions that focus on these peri-urban areas. The study further critiques the DAP's effectiveness, revealing a disconnect between regional policy implementation and local outcomes. This research proposes a validated, scalable framework for urban master plans that adapts to the complex socio-ecological contexts of rapidly urbanizing regions.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

Fungal infections (FIs) are spreading globally causing a significant public health concern. However, its documentation remains sparse in Africa, particularly in Rwanda. This literature review, aims to assess the risk and document current gaps in evidence and policy. It summarizes the published data about FIs in Rwanda, including ten reports published between 1972-and-2022. Blastomyces, Candida, Cryptococcus, Histoplasma, Microsporum, Pneumocystis, Rhinosporidium, and Trichophyton caused human infections. These infections primarily affected the brain, respiratory, urinary and reproductive organs, and they were diagnosed using culturing, histopathology, immunology, and/or microscopic techniques. Our findings provide an overview of the diversity and distribution of FIs, highlighting significant limitations in the country’s diagnostic capacity and surveillance system for FIs. Also, indicating severe gaps in evidence to inform policymaking, guide strategic planning and intervention, underscoring the urgent need to build national capacity in fungal diagnosis, surveillance, and research. Raising awareness among the public, scientific community, healthcare providers, and policymakers remains crucial. Furthermore, this report reveals the threats of FIs on public health and food insecurity in Rwanda. A Multisectoral One Health Strategy is essential in research and intervention to determine and reduce the health and safety impacts of fungal pathogens on human, animal, and the environment.

Maize is the staple cereal in Malawi, with a daily per capita consumption of 383g (dry matter basis), primarily consumed as dehulled maize flour used to cook nsima, a thick porridge. However, the extent of mass and nutrient loss during dehulling remains unclear in this food-insecure country, where the household maize harvest typically lasts only 6–7 months. In the current study, a milling experiment to determine yield and micronutrient losses was conducted. Milling batches (30 kg) of four maize grain varieties were dehulled at three abrasive disk dehullers under controlled conditions. Mass losses ranged from 18.8% to 42.7%, with a mean of 28.2±5.7%. Maize variety and dehuller significantly affected mass loss (p<0.05). Initial protein, iron, and zinc concentrations were 8.8 ±1.0 g/100g, 20.5±2.0 µg/g, and 18.2 ±2.6 µg/g, respectively. Post-dehulling nutrient true retention varied for protein (49.7% to 75.6%, mean=64.7±7.0%), iron (18.7% to 71.6%, mean=37.6±12.0 %), and zinc (11.0% to 46.2%, mean=27.9±8.7 %). Maize variety significantly influenced mass and protein loss (p < 0.05), while dehuller influenced mass, iron, and zinc losses. However, no significant difference (p > 0.05) was found in the interaction between dehullers and variety on mass and nutrient losses, respectively. Given Malawi's precarious food insecurity situation, transitioning from dehulled maize flour nsima to whole maize flour or less refined nsima, is imperative. Our study findings can have food and nutritional savings for other southern Africa countries where the dehulling practice is rampant.

Shear dynamics simulation under extreme pressure was used to optimise the composition of ester-based lubricant base oil and extreme pressure additives. As a result, the ester-based lubricant in the weak-gel drilling fluid achieves reduction and increases the efficiency in drilling construction, and the field operation efficiency improves. The results of base oil lubrication simulation show that three base oils, namely, methyl oleate, ethyl oleate and butyl oleate, can be stably adsorbed on the surface layer of the shear surface. Methyl oleate has the lowest system temperature after shear stabilisation and has a high load-bearing capacity. The shear stress of methyl oleate decreases by changing the initial shear temperature and speed. It increases by 6.36 MPa when the speed increases from 10 m/s to 30 m/s. At this time, the shear stress of butyl oleate increases by 10.11 MPa. The results of the four-ball friction experiments show that the radius of the abrasion spot of methyl oleate is 179.83 μm, which is smaller than that of the other two base oils. Moreover, the friction coefficient of methyl oleate is 0.0018, which is approximately 1/3 of that of butyl oleate. Methyl oleate has better lubrication efficiency. The shear simulation results are consistent with the experimental results. The simulation can be used for the molecular design of lubricant materials. The oleic acid amide–containing amine group and the glyceride oleic–containing hydroxyl group were selected as the extreme pressure functional components for shear simulation. Results show that the shear stress of oleic acid amide is much lower than that of oleic acid glyceride when the initial shear temperature and speed change. The extreme pressure lubrication component–containing amine group is better than the extreme pressure lubrication material–containing hydroxyl group. The effects of different oleamide contents in the two-component mixtures on the lubricating properties were investigated through shear simulation, with methyl oleate as the base oil and oleamide as the extreme pressure functional component. The simulation results show that the lubricant has the optimal shear stress when 10% oleamide is added to the lubricant. The base properties of the lubricant were tested using a mixture of 90% methyl oleate and 10% oleamide, formulated as a lubricant. Results show that the friction coefficient can be reduced to 0.03 when 0.5% of the lubricant is added to the base mud. Moreover, the lubricant film formed shows high strength. Then, 1% lubricant was added to the weak-gel drilling fluid to evaluate the effect of the lubricant on the gel structure of the drilling fluid. Results show that adding lubricant does not affect the rheological properties of the drilling fluid. The gel structure of the system also remains stable even after 7 days of continuous ageing. The results of the field experiments in Hua3-01 well show that adding 1% ester-based lubricant to the field drilling fluid reduces the drilling friction by 33%. Thus, the efficiency of directional side drilling can be effectively improved, complicated accidents, such as poor starting and stopping of drilling and stuck jamming, can be avoided, and the goals of reducing quantity and increasing efficiency can be completed.

This study presents the design and comprehensive 3D multiphysics simulation of a novel microfluidic immunosensor for real-time, non-invasive monitoring of pro-inflammatory biomarkers in human sweat. The patch-like device, designed using COMSOL Multiphysics, integrates magnetofluidic manipulation with direct-field capacitive sensing. The sensor comprises two distinct units: an immunocomplex enhancement unit, employing a series of microcoils to optimize the binding efficiency, reaction kinetics, and homogeneity of biomarker-magnetic nanoparticle (MNP) interactions, thereby enhancing the sensor's specificity; and a layered capacitive sensing unit, designed to concentrate and detect biomarker-tagged MNPs, thus amplifying sensitivity. Simulations of the capacitive sensing unit revealed a substantial sensitivity increase of up to 42.48\% at an 85\% MNP concentration within the detection zone. These findings highlight the potential of the proposed immunosensor for efficient and precise real-time biomarker monitoring, which may facilitate early disease diagnosis and enable personalized healthcare interventions.

Two coupled climate models which participated the CMIP6 project (Coupled Model Intercomparison Project Phase 6), the Earth System Model of Chinese Academy of Sciences version 2 (CAS-ESM2-0) and the Nanjing University of Information Science and Technology Earth System Model version 3 (NESM3), were assessed in terms of the impact of four new sea ice parameterization schemes. These four new schemes are related to air-sea heat flux, radiation penetration and absorption, melt ponds, ice-ocean flux, respectively. To evaluate the effectiveness of these schemes, key sea ice variables with and without these new schemes, such as sea ice concentration (SIC) and sea ice thickness (SIT), were compared against observation and reanalysis product from 1980 to 2014. The simulations followed the design of historical experiments within the CMIP6 framework. The results revealed that both models demonstrated improvements in simulating Arctic SIC and SIT when the new parameterization schemes were implemented. The model bias of SIC in some marginal sea ice zones of Arctic was reduced, especially during March. The SIT was increased and the transpolar gradient of SIT was reproduced. The changes of spatial pattern of SIC and SIT after adding new schemes bear similarities between the two coupled models. This suggests that the new schemes have potential for broad application in climate models, especially for those with underestimated SIT.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

Well-intentioned regulations to protect Canada’s most productive farmland restrict large-scale so-lar photovoltaic (PV) development. The recent innovation of agrivoltaics, which is the co-development of land for both PV and agriculture, makes these regulations obsolete. Burgeoning agrivoltaics research has shown agricultural benefits including increased yield for a wide range of crops, plant protection from excess solar energy and hail, improved water conservation while maintaining agricultural employment and local food supplies. In addition, the renewable electricity generation decreases greenhouse gas emissions while increasing farm revenue. As Canada in general, and Ontario in particular, is at a strategic disadvantage in agricultural without agrivoltaics, this study investigates the policy changes necessary to capitalize on the benefits of using agrivoltaics in Ontario. Land use policies in Ontario are reviewed. Then, three case studies (peppers, sweet corn and winter wheat) are analyzed for agrivoltaic potential in Ontario. These results are analyzed in conjunction with potential policies that would continue to protect the green-belt of the Golden Horseshoe, while enabling agrivoltaics in Ontario. Four agrivoltaic policy areas are discussed: increased research and development, enhanced education/public awareness, mechanisms to support Canada’s farmers converting to agrivoltaics and using agrivoltaics as a potential source of trade surplus with the U.S.

Addressing the significant challenge in high-speed cotton dibbling operations in Xinjiang—specifically, the duck bill’s ("Duck bill" is a type of duck-billed bunch planting mechanism or component). shortened opening duration leading to seed throwing and floating—a new crawler-type delayed hole-forming mechanism has been designed. This mechanism extends the duck bill horizontally, thereby prolonging its opening time, enabling cotton sowing speeds of up to 6 km/h. Following agronomic principles for cotton planting, the overall layout of the crawler-type hole-forming mechanism, the structural parameters of the key components and the trajectory of the hole-forming are determined. We use the Discrete Element Method (DEM) and multi-body dynamics coupling method to simulate and analyze the motion process of the device. The fixed the tilt angle of the duck bill α(A), the depth of the duck bill hole-forming into the soil h(B), and the angle of rotation of the moving duck bill β(C) were taken as the experimental factors, with the longitudinal length of cotton seed hole (Y1) and the hole-forming depth of cotton seed hole (Y2) as the response values. The parameter range of each factor and the preliminary influence on the response value were determined through pre-experiments and single-factor simulation test. Based on RecurDyn-EDEM coupling, a quadratic regression orthogonal rotation combination simulation test was carried out. The results show that the order of the primary and secondary factors affecting the Y1 of the time-lapse hole-forming device was: A > C > B. The order of primary and secondary factors affecting the Y2 of the delayed hole forming device was: B > C > A. When the A was 2.4 °, the B was 42.4 mm, and the C was 30.5 °, the performance of the hole-forming was the best, and the Y1 was 26.4 mm, and the Y2 was 25.0 mm. The bench verification test results show that under the optimized combination of operating parameters, the average Y1 was 29.1 mm, and the average Y2 was 23.2 mm. Compared with the results of the previous coupled simulation model, the average relative errors of the two are 7.23 % and 4.36 %, respectively, indicating the accuracy and effectiveness of the established DEM simulation model and virtual test analysis. The hole-forming area and the opening time of the duck bill after the stable operation of the machine were recorded and measured. The calculated hole dislocation rate Hc was 4.33 %, which did not exceed the national standard requirement of 6 %. The qualified rate of hole distance Hx was 94.33 %, which was much higher than the national standard requirement of 80 %. The average opening time of the duck bill at a speed of 6 km/h is 0.45 s, which is much longer than the time required for cotton seeds to fall from the duck bill 0.11 s. It meets the requirements of high-speed cotton planting in China and facilitating advancements in future high-speed planter technology.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

Low fertility is a critical social problem worldwide, and infertility has a prevalence of 15%. This cross-sectional study aimed to understand the factors affecting the usage and satisfaction of Korean medicine (KM) in subfertile women. An online survey was conducted from November 3 to November 8, 2021. The survey collected basic information, KM treatment experience, and satisfaction from women who experienced poor pregnancy. The t-test and chi-square test (χ2-test) were used to determine the overall characteristics of the subjects and factors affecting the utilization and satisfaction of KM treatment. Of the total of 29,465 people, 4,922 read the survey email, and 601 responded. After excluding 51 insincere respondents, 550 respondents were included in the final analysis. Of these, 43.1% had experience with conventional treatment, and 15.6% had received KM treatment. Integrative subfertility treatment was significantly more common (24.9%) than KM treatment alone (10.2%) (P=0.00). Women with no childbirth experience (P=0.01) and those with a master’s degree (P=0.01) were more willing to participate in the ‘KM Support Project for Subfertility’. Our findings suggest that subfertile patients prefer integrated medical treatment over KM alone. Further studies are needed to assess the status of integrative medicine treatment, satisfaction with each KM intervention, factors for low satisfaction, and patient requirements.

The fractional advection-dispersion equation FADE plays an important role, especially in explaining the process of solute-transport in natural porous media with different degrees of heterogeneity. However, studies of the flow and transport of contaminants in the underground environment are based on the knowledge of many functional parameters of the subsoil. The delay factor caused by nonlinear absorption is one of these parameters inheriting significant ambiguities in its estimation in heterogeneous media. In the study, a fractional advection-dispersion FADE model was developed by the implicit Euler method, based on a Grunwald and Caputo-Liousville approximation to explicitly evaluate and simulate the transport mechanism of contaminants in media with unsaturated porous materials subjected to a nonlinear sorption model. Better solute mass retention was observed for fractional advection-dispersion FADE model. Moreover, the absorption parameter of the retardation coefficient has a better impact on the motion of the solute in a saturated porous medium. In other words, it has a significant effect on the dispersion of pollutants in aquifers. This study highlights the need to characterize the aquifer to predict solute transport in porous media.

Tinnitus is a common phantom auditory percept, believed to be related to plastic changes in the brain due to hearing loss. However, tinnitus can also occur in absence of any clinical hearing loss. Then, since there is no hearing loss, the mechanisms that drive plastic changes remain largely enigmatic. Previous studies showed subtle differences in sound-evoked brain activity associated with tinnitus in subjects with tinnitus and otherwise, normal hearing, but the results are not consistent across studies. Here, we aim to investigate those differences using monaural rather than binaural stimuli. Sound-evoked responses were measured using functional magnetic resonance imaging (MRI) in participants with and without tinnitus. All participants had clinically normal audiograms. The stimuli were pure tones with frequencies between 353 and 8000 Hz, presented monaurally. A Principal Component Analysis (PCA) of the response in the auditory cortex revealed no difference in tonotopic organization, which confirmed earlier studies. A GLM analysis showed hyperactivity in the lateral areas of the bilateral auditory cortex. Consistent with the tonotopic map, this hyperactivity mainly occurred in response to low stimulus frequencies. This may be related to hyperacusis, which was associated with tinnitus found in the parahippocampus. This may reflect an interference between tinnitus and spatial orientation.

This paper proposed a three-layer distributed simulation network architecture: 1. Distributed virtual simulation network, 2. Perception and control sub-network, and 3. Collaborative communication service network. This simulation architecture runs on a distributed platform. The platform can provide a unique virtual scenario and several simulation services to verify the individual robot system's basic perception, control, and planning algorithms and the distributed collaborative algorithms of heterogeneous multi-robot systems. Furthermore, we designed a simulation experiment scenario for classical heterogeneous robot systems such as unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs). At last, We gave a rough estimation model of the bandwidth.

Although, promotion of urbanization culture in recent decades has made inevitable development of cities in the world, however, the development can be guided in a direction that leave, to the extent possible, minimum socioeconomic and environmental impacts. For this, it is required to first forecast auto-spreading orientation of cities and suburbs in rural areas over time and then avoid shapeless growth of cities. This paper is an attempt to develop a dynamic hybrid model based on logistic regression (LR), Markov chain (MC), and cellular automata (CA) for prediction of future urban sprawl in fast-growing cities. The model was developed using 12 widely-used urban development criteria, whose significant coefficient was determined by logistic regression, and validated by relative operating characteristic (ROC) analysis. The validated model was run in Guilan, a tourist province in northern Iran with a very high rate of urban development. For this, changes in the area of urban land use were detected over the period of 1989 to 2013 and then, future sprawl of the province was forecasted by the years 2025 and 2037. The analysis results revealed that the area of urban land use was increased by more than 1.7 % from 36012.5 ha in 1989 to 59754.8 ha in 2013, and the area of Caspian Hyrcanian forestland was reduced by 31628 ha. The results also predicted an alarming increase in the rate of urban development in the province by the years 2025 and 2037, during which urban land use is predicted to develop 0.9 % and 1.38 %, respectively. The development pattern is expected to be uneven and scattered, without following any particular direction. The development will occur close to the existing or newly-formed urban basements as well as around major roads and commercial areas. This development, if not controlled, will lead to the loss of 13863 ha of Hyrcanian forests and if the trend continues, 21013 ha of Hyrcanian forests and 20208 ha of Barren/open lands are expected to be destroyed by the year 2037. In general, the proposed model is an efficient tool for the support of urban planning decisions and facilitates the process of sustainable development of cities by providing decision-makers with an overview on future development of cities where the growth rate is very fast.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

In this work, two plasmonic structures with two different periodic nanostructures (nanodisk and nanostrip arrays) separated from the gold layer by an ultrathin dielectric Al2O3 layer are proposed, and their optical properties are simulated as 3-dimensional models using COMSOL Multiphysics software tool. The optical responses, such as the amplification of the electric field and the scattering, absorption and extinction cross sections of the two structures, are investigated and compared. The results show that both structures show strong field enhancement in their gap layer, and the structure with the periodic array of metal nanodisks shows stronger field enhancement and larger absorption, extinction, and scattering cross sections in its dipole resonance wavelength, which is defined as a bright plasmonic mode. In addition, some weaker resonant modes are observed for both structures and the reason for their generation is dis-cussed. The analysis of different possible modes in such structures is crucial for their application in various fields.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

In this paper, the boiling flow inside a nanochannel with 700000 argon particle has been simulated by molecular dynamics (MD) simulation. This approach has been employed to analysis the superheated flow and its heat transfer pattern as well. For all simulations an external thrust force varying from 1 PN to 12 PN is exerted on inlet nanoparticles along the channel to have the forced annular boiling flow. Computations reveal that saturation condition and superheat degree have significant impacts on the liquid-vapor interface. Furthermore, because of the major influence of surface tension throughout a nanochannel, the x-velocity of liquid film and vapor core has not considerable fluctuations and stay smooth. All provided results show the behaviors completely similar to the available outcomes in the literature.

Surgical simulators are crucial in early craniofacial and plastic surgical training, necessitating synthetic materials that accurately replicate tissue properties. Recent critiques of our lab’s currently deployed silicone surrogate have highlighted numerous areas for improvement. To further refine our models, our group's objective is to find a composition of materials that is closest in fidelity to native oral mucosa during surgical rehearsal by expert craniofacial surgeons. Fifteen platinum silicone-based surrogate samples were constructed with variable hardness and slacker percentages. These samples underwent evaluation of tactile sensation, hardness, needle puncture, cut resistance, suture retention, defect repair, and tensile elasticity. Expert craniofacial surgeon evaluators provided focused qualitative feedback on selected top-performing samples for further assessment and statistical comparisons. Evaluation revealed surrogate characteristics with satisfactory to good performance. Sample 977 exhibited the highest performance, and comparison with the original surrogate (sample 810) demonstrated significant improvements in critical areas, emphasizing the efficacy of the refined composition. The study identified a silicone composition that directly addresses the feedback received by our team’s original silicone surrogate. The study underscores the delicate balance between biofidelity and practicality in surgical simulation. The need for ongoing refinement in surrogate materials is evident to optimize training experiences for early surgical learners.

Surgical simulators are crucial in early craniofacial and plastic surgical training, necessitating synthetic materials that accurately replicate tissue properties. Recent critiques of our lab’s currently deployed silicone surrogate have highlighted numerous areas for improvement. To further refine our models, our group's objective is to find a composition of materials that is closest in fidelity to native oral mucosa during surgical rehearsal by expert craniofacial surgeons. Fifteen platinum silicone-based surrogate samples were constructed with variable hardness and slacker percentages. These samples underwent evaluation of tactile sensation, hardness, needle puncture, cut resistance, suture retention, defect repair, and tensile elasticity. Expert craniofacial surgeon evaluators provided focused qualitative feedback on selected top-performing samples for further assessment and statistical comparisons. Evaluation revealed surrogate characteristics with satisfactory to good performance. Sample 977 exhibited the highest performance, and comparison with the original surrogate (sample 810) demonstrated significant improvements in critical areas, emphasizing the efficacy of the refined composition. The study identified a silicone composition that directly addresses the feedback received by our team’s original silicone surrogate. The study underscores the delicate balance between biofidelity and practicality in surgical simulation. The need for ongoing refinement in surrogate materials is evident to optimize training experiences for early surgical learners.

: In this paper we present an optimization of the planar manufacturing scheme for stretch-free, shape induced metal interconnects to simplify the fabrication with the aim of maximizing the flexibility in the structure regarding to stress and strain. The Formation of trenches between silicon islands are actively used in the lithographic process to create arc shape structures by spin coating resist into the trenches. The resulting resist form is used as a template for the metal lines, which are structured on top. Because this arc shape is beneficial for the flexibility of these bridges. The trench depth as a key parameter for the stress distribution is investigated by applying numerical simulations. The simulated results show that the increase in penetration depth of the metal bridge into the trench increases the tensile load which is converted into a shear Force Q(x), that usually leads to increased strains the structure can generate. For the fabrication the filling of the trenches with resist is optimized by varying the spin speed. Compared to the theoretical resistance, the current-voltage measurements of the metal bridges show a similar behavior and almost every structural variation is capable of functioning as a flexible electrical interconnect in a complete island-bridge array.

To address the requirements of sonar imaging, such as high receiving sensitivity, wide bandwidth, wide receiving angle, an AlN PMUT with an optimized ratio of 0.6 for the piezoelectric layer diameter to backside cavity diameter is proposed in this paper. A sample AlN PMUT is designed and fabricated with SOI substrate-based bulk MEMS process. The characterization test result of the sample demonstrates a -6 dB bandwidth of approximately 500 kHz and a measured receiving sensitivity per unit area of at 1.37 V/μPa/mm2, which significantly surpasses the performance of previously reported PMUTs. The -6 dB horizontal angles of the AlN PMUT at 300 kHz and 500 kHz are measured 68.30° and 54.24°, respectively. To achieve an accurate prediction of its characteristics when being packaged and assembled in a receive array, numerical simulations with the consideration of film stress are conducted. The numerical result shows a maximum deviation of ±7% in the underwater receiving sensitivity across the frequency range of 200 kHz to 1000 kHz and a deviation of about 0.33% in the peak of underwater receiving sensitivity comparing to the experimental data. By such good agreement, the simulation method reveals its capability of providing theoretical foundation for enhancing the uniformity of the AlN PMUTs in future studies.

This paper focuses on environmental policies for mitigating the impacts of climate change on the Taj Mahal, an iconic structure built on the banks of the Yamuna River from 1632 to 1653 with a blend of Persian and Indian architectural styles. The Taj Mahal is threatened by damage caused by climate change, including air pollution resulting in acid rain and floods that lead to erosion and discoloration of the main marble material of the Taj Mahal. This study employs a Systematic Literature Review (SLR) of peer-reviewed journal articles with a primary focus on environmental policy, the impacts of climate change, and the preventive measures undertaken by the Indian government. Based on the analysis of 270 papers, it is concluded that out of the total, 30 papers specifically address objectives relevant to this research. The study period spans from 2014 to 2024. The research findings reveal that air pollution has a significantly adverse impact on the Taj Mahal. Furthermore, nine policies are generally identified from the journal literature review aimed at preserving and protecting the Taj Mahal from the negative effects caused by air pollution.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

Hydraulic fracturing has enabled production from unconventional reservoirs in the U.S., but production rates often decline sharply, limiting recovery factors to under 10%. This study optimizes the CO2 huff-n-puff process for multistage-fractured horizontal wells in Wolfcamp A formation in the Delaware Basin. The potential for enhanced oil recovery and CO2 sequestration simultaneously was addressed using a coupled geomechanics-reservoir simulation. Geomechanical properties were derived from a 1D mechanical earth model and integrated into reservoir simulation to replicate hydraulic fracture geometries. The fracture model was validated using a robust production history matching. Fluid phase behavior analysis refined the equation of state, and 1D slim tube simulations determined a minimum miscibility pressure of 4300 psi for CO2 injection. After the primary production phase, various CO2 injection rates were tested from 1 to 25 MMSCFD/well, resulting in incremental oil recovery ranging from 6.3% to 69.3%. Different injection, soaking, and production cycles were analyzed to determine the ideal operating condition. The optimal scenario improved cumulative oil recovery by 68.8% while keeping the highest CO2 storage efficiency. The simulation approach proposed by this study provides a systematic workflow for evaluating and optimizing CO2 huff-n-puff in hydraulically fractured wells, enhancing the recovery factor of unconventional reservoirs.

Supporting the implementation of school food and nutrition policies (SFNPs) is an international priority to encourage healthier eating among children and youth. Schools are an important intervention setting to promote childhood nutrition, and many jurisdictions have adopted policies, guidelines, and programs to modify the school nutrition environment and promote healthier eating. The purpose of this study was to explore the association between perceived adequacy and capacity for SFNP implementation on food availability and policy adherence in the province of Nova Scotia (NS), Canada, one of the first regions in Canada to launch a comprehensive SFNP. A cross sectional online survey was conducted in 2014-15 to provide a current-state of policy implementation and adherence. Adequacy and capacity for food policy implementation was used to assess policy adherence through the availability of prohibited ‘minimum’ nutrition foods. An exploratory factor analysis was conducted on a selected of available foods and ‘slow’ and ‘quick’ service food composition measures were dichotomized for food availability. Schools with above perceived average adequacy and capacity for policy implementation had more than three times (3.62) greater odds of adhering to a lunch policy, while schools that adhered to a snack and lunch policy had 52% and 82% lower odds of serving quick service foods, respectively. This study identified the need for appropriate adequacy and capacity for policy implementation to ensure policy adherence and improve the school food environment. These findings highlight the potential of SFNPs to have a positive impact on childhood nutrition, but adequately supporting their implementation is critical to ensure their impact.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

Carbonaceous materials have gained significant attention in recent years for their various applications in the field of medicine and biotechnology. This comprehensive review explores the synthesis and characterization of carbon-based materials and their potentials in various medical applications. The paper delves into the methods of fabrication of carbon-based nanoparticles, such as carbon nanotubes, biochar, and graphene, while highlighting their unique properties. Characterization techniques, such as microscopy, spectroscopy, and surface analysis, are discussed to provide insights into the chemical and structural properties of these materials. Furthermore, the review examined their wide-ranging medical applications, encompassing tissue engineering, drug delivery, biosensing, and imaging, showcasing the versatility and promising contributions of carbonaceous materials in the healthcare industry. The review outlines the current challenges and prospects in the field, emphasizing the growing significance of carbon-based materials as valuable tools in advancing medical science and technology, as well as public health.

Decision sciences (DSC) involve studying complex dynamic systems and processes to aid informed choices subject to constraints in uncertain conditions. It integrates multidisciplinary methods, techniques, and strategies to evaluate decision engineering processes, identifying alternatives and providing insights towards enhancing prudent decision-making. This study analyzes the evolutionary trends and innovation in DSC education and research to uncover the transformations over the years. We employ the science mapping method, text analytics, and metadata from bibliographic databases to evaluate thematic and social structures. The results highlight data science methods, including data mining and business/learning analytics as essential components. The evolutionary trends in DSC education and research mirror the development in practice, including technological transformation, computer science advances, and engineering processes. Sustainable education through virtual/online learning also constitutes a significant component of scientific production. The evolutionary trends in DSC education and research highlight innovative pedagogical approaches and strategies, including computer simulation and games ('play and learn'). The current era witnessed generative artificial intelligence (GenAI) adoption (e.g., ChatGPT) in teaching, learning, and scholarly activities amidst challenges (academic integrity, plagiarism, intellectual property violations, and other ethical and legal issues). Future research will implement and integrate AI automatic detection systems to address some GenAI adoption challenges.

The consistent and continuous growth in the world’s population is creating many challenges for public policymakers in the different life areas, including dealing with the increasing amounts of waste that are generating problems involving air and land pollution and a shortage of land for waste disposal. This study presents the results of public policy on managing municipal waste, as manifested in the quantity and rate of waste collected throughout Israel in recent years and disposed of in the various landfills and in analysis of the political and economic factors affecting this policy. The study combines a quantitative and qualitative approach, where the quantitative study includes analysis of statistical data based on information from the Central Bureau of Statistics, the Ministry of Environmental Protection, the Ministry of Finance, and others, and the qualitative study relies on reading and analyzing primary documents of the different government ministries on Israel’s waste disposal policy and information in the media on this issue. The research findings attest to an increase in the amount of municipal waste dumped in Israel, a merely slight decrease in the rate of landfilling as a proportion of all municipal waste disposal, and a merely slight increase in the rate of municipal waste recycled in recent years. The research conclusions stress the effects of the landfill levy and the Cleanliness Maintenance Fund on one hand, and of the government instability in the Ministry of Environmental Protection, the positivist policy embraced by decision makers in the Ministry of Environmental Protection, and the power struggles between Israel’s different ministries on the other, as the respective economic and political factors affecting Israeli policy on municipal waste management.

This article focuses on the economic dimensions of maternal health, highlighting the benefits of investing in maternal healthcare and the policy implications for sustainable development. Through a comprehensive review of the literature, the article explores the economic impact of maternal health, including its effects on human capital, productivity, and healthcare costs. It emphasizes the importance of addressing social determinants such as access to healthcare services, education, employment, income, and geographical disparities. By prioritizing maternal health, societies can unlock the economic potential of women, promote inclusive growth, and reduce gender disparities. The article discusses policy interventions, including the importance of healthcare infrastructure, financial support for maternal healthcare, and promoting gender equality. It also emphasizes the need for future research to quantify the economic benefits and evaluate the cost-effectiveness of different interventions. Overall, the article underscores the economic imperative of investing in maternal health and provides valuable insights for policymakers and researchers seeking to enhance maternal health outcomes and promote sustainable economic development.

Should our planet be visited by an extraterrestrial civilization, the prevailing assumption would undoubtedly be that the extraterrestrial civilization is Type I i.e. its capacity for interstellar travel results from its technological development. This assumption is dangerous for it unnecessarily leads to the Extraterrestrial Tandem Hypothesis (ETH): the belief than an extraterrestrial civilization technologically capable of interstellar travel must also be technologically compatible with the inexorably rapid annihilation of life on Earth. Such a state of things would compromise the planet’s capacity to stage a confident defense should the extraterrestrials prove belligerent. The presumption of Type I extraterrestrials (on the premise of the capacity for interstellar travel alone) is unfounded as extraterrestrials may be Type II i.e. capable of interstellar travel by virtue of natural intrinsic or extrinsic factors. This paper advances, most importantly, that the fundamental policy of first contact should be the employment of various strategies toward the evaluation of the technological capacity of visiting extraterrestrials. This evaluation must be particularly devoted to the detection of Type II extraterrestrials masquerading as Type I (using concealment and Wizard of Oz strategies). Integral to this detection are the concepts of the precedence relation and The Extraterrestrial Exclusion Principle (EEP). A precedence relation is a qualitative relation expressing the relative difficulty of producing a technological action. The Extraterrestrial Exclusion Principle states that a Type I extraterrestrial life form is excluded from certain actions. Such actions are lower in precedence than interstellar travel and may be described as in violation of the EEP or EEP forbidden. EEP actions reveal extraterrestrials to be Type II. As an example, the value of the Hawking Warning is subjected to EEP analysis. Furthermore, a hypothetical conundrum in linguistics termed the Kryptonian Linguistic Paradox (KLP) is discussed as a case of an EEP forbidden act. Finally, the paper explores the limitations of the stated fundamental policy of first contact.

Human activities (e.g., exploitation, utilization, and conservation) exert substantial impact on forest ecological functions (FEF). The human influence on FEF significantly varies across developmental stages, which are attributed to the temporal and spatial in nature. This study evaluates some notable FEF indices (FEFI) in the 448 counties within the Yellow River basin (YRB) using panel data from the Seventh to Ninth National Forest Inventory. Data analysis involves employing the residual trends, geographical and temporal weighted regression. Results indicate that, firstly, the overall forest ecological function in the YRB is moderate to inferior, with superior FEF in counties endowed with more natural forest resources. Afforestation demonstrates a short-term improvement, but its effectiveness diminishes over time. Secondly, the positive spatial correlation is stronger among counties, characterized by both high-high and low-low agglomeration effects. Scattered planting, simple stand structure, and concentrated harvesting of forests at the identical stand ages hinder the formation of complex and large-scale FEF agglomerations. Thirdly, significant spatial-temporal differences exist in the impact of human activities on FEF. In the upper reaches of the basin, increased vegetation coverage through agricultural and forestry production benefited FEF, however, some over-exploitation of forests and grasslands is observed there. In the middle reaches, the economic development, expanding population and the greening activities help to improve FEF effectively, but excessive water using in agricultural production brought more difficulties to FEF improvement. In the lower reaches of the basin, improved wastelands and forest protection positively influence FEF. This study recommends that county governments should prioritize forest management with multi-species and multi-layered complex forests. Each county should define its position in regional development and ecological protection, considering the potential impacts on neighboring regions. This holistic approach promotes more effective integrated regional management.

Agricultural greenhouse is largely answered in the agricultural sphere, despite the shortcomings it has, including overheating during the day and night cooling which sometimes results in the thermal inversion mainly due to its low inertia. The glasshouse dressed chapel is relatively more efficient than the conventional tunnel greenhouse. Its proliferation on the ground is more or less timid because of its relatively high cost[14-22]. Agricultural greenhouse aims to create a favorable microclimate to the requirements of growth and development of culture, from the surrounding weather conditions, produce according to the cropping calendars fruits, vegetables and flower species out of season and widely available along the year. It is defined by its structural and functional architecture, the quality thermal, mechanical and optical of its wall, with its sealing level and the technical and technological accompanying[12-13]. The greenhouse is a very confined environment, where multiple components are exchanged between key stakeholders and them factors are light, temperature and relative humidity[8]. This state of thermal evolution is the level sealing of the cover of its physical characteristics to be transparent to solar, absorbent and reflective of infrared radiation emitted by the enclosure where the solar radiation trapping effect otherwise called "greenhouse effect" and its technical and technological means of air that accompany. The socio-economic analysis of populations in the world leaves appear especially the last two decades of rapid and profound transformations These changes are accompanied by changes in eating habits, mainly characterized by rising consumption spread along the year[14]. To effectively meet this demand, greenhouse-systems have evolved, particularly towards greater control of production conditions (climate, irrigation, ventilation techniques, CO2 supply, etc ...). Technological progress has allowed the development of greenhouses so that they become increasingly sophisticated and of an industrial nature (heating, air conditioning, control, computer, regulation, etc ...). New climate driving techniques have emerged, including the use of control devices from the classic to the use of artificial intelligence[10-11] such as neural networks and / or fuzzy logic, etc... As a result, the greenhouse growers prefer these new technologies while optimizing the investment in the field to effectively meet the supply and demand of these fresh products cheaply and widely available throughout the year.

Background/Objectives: The purpose of this study was to evaluate the relationship between 1-year mortality and health insurance benefit extension policy items in severe pneumonia pa-tients requiring mechanical ventilation using a South Korean nationwide cohort. Methods: A nationwide population-based retrospective study was conducted using the Korean National Health Insurance database. A total of 1,099 patients (542 patients in the health insurance benefit item group and 557 patients in the control group) were included. The primary outcome was 1-year mortality. Results: Among patients with health insurance benefit extension policy items, 203 patients (37.5%) were diagnosed with hemato-oncological disease, who were categorized as group A, and 339 patients (62.5%) were diagnosed with cerebrovascular, cardiovascular, or rare diseases, who were categorized as group B. Group B had lower 1-year mortality (50.7% vs. 62.5%, P

Despite ample warning and significant lead time, global society has not acted sufficiently to combat climate change, and global carbon dioxide emissions are now about 60% higher today than in 1990 [1]. This paper uses marine fisheries as an analog model to compare with the many similar management issues faced with global climate change. Both marine fisheries and global climate change are complex systems that have similar properties that make management very difficult. A simple fishery prototype model is used to educate citizens about similar issues of dynamic complexity found in climate change models. We highlight how our slow reaction time to global climate change can be thought of as a mismatch between our cognitive abilities and the nature of global collective problems. Understanding the history and system structure of marine fisheries can provide insight into managing global climate change. We suggest ways to improve communication between science and citizens for updating mental models and changing climate policy.

Cigarette butts (CBs) are the most diffuse waste in the world, often abandoned in the environment without proper disposal. They are dangerous because of the numerous harmful chemicals poten-tially released in the environment. There are, in literature, several technological options for CB recycling, but some critical concerns could affect their effectiveness due to the quality and quantity of CB litter collected in the proper way. The present paper focuses on policy framework social behavior, waste collection and transport and technological processes. The Extended Producer Responsibility scheme for CBs is proposed at European level as an action to tackle CB litter and encourage sustainable product development. The CB waste collection and transport is a key step for bringing CB to the recycling process. The main concern is the small quantity of CBs collected: 0.06 % of the municipal waste and 0.18 % of the unsorted waste in the administrative area of Pe-rugia. Another crucial issue is the need for behavioral interventions to increase education and awareness of smoker citizens, addressing the discrepancy between smokers’ behaviors and beliefs.

The study's motivation is to gauge the nexus between economic policy uncertainty and financial innovation for the period 2004M1 to 2018M12 in BRIC nations. For establishing a long-run cointegration study applied Autoregressive Distributed Lagged (ARDL) and asymmetry effects of economic policy uncertainty investigated following nonlinear framework known as NARDL. Furthermore, directional causality is established by performing a non-granger causality test. Cointegration test results of Fpss, Wpss, and tBDM confirmed the long-run association between EPU and financial innovation. On the other hand, the Wald test results proved asymmetry effects furring from EPU to financial innovation both in the long-run and short-run. Referring to asymmetry effects that positive and negative shocks in financial innovation, the study revealed that negative linkage between shocks in EPU and financial innovation in the long-run but short-run effects are insignificant. Furthermore, financial innovation measured by R&D investment exhibits positive linked with shocks in EPU, implying that uncertainty induces innovation in the economy. Refers to directional causality estimation, the study revealed evidence supporting the feedback hypothesis between EPU and financial innovation in all sample countries.

Perovskite solar cells (PSCs) are vital for their optical and electrical properties, with lead-based PSCs reaching a remarkable efficiency of 26.1%, while tin-based counterparts achieve 18.71%. Due to lead's toxicity, there's a push for alternatives like tin. However, tin-based PSCs suffer from stability issues and high defect density states, necessitating the development of cost-effective, high-performance, and eco-friendly alternatives. In this study, we designed a hetero-junction architecture using MASnI3-based Perovskite, opti-mized with SCAPs-1D. After exhaustive analysis, our device achieved a power conversion efficiency of 24.18%, with enhanced parameters including Voc of 0.09323V, Jsc of 30.8360 mA/cm2, and FF of 84.10%. Recombination rates, particularly Shockley-Read Hall recom-bination, were significantly reduced. Parametric analyses, encompassing absorber layer thickness, band gap, defect density, doping concentration, and operating temperature, in-dicate potential efficiency enhancements. This underscores the viability of Sn-based PSCs as a cost-effective, efficient, and environmentally benevolent alternative to lead-based counterparts, promising advancements in future research and development efforts.

The object of study in the article is the auxiliary variable-frequency electric drive onboard of an AC electric locomotive, and more precisely, the structure and parameters of the control system of the active corrector of power factor (ACPF), which is part of the electric drive, as a unit that ensures electromagnetic compatibility of the electric drive with other equipment on board the electric locomotive and catenary and its energy efficiency. The topic of the article's research is the substantiation of the structure of the ACPF control system, the choice of types (transfer functions) of controllers and the calculation of their parameters. The research method chosen was the calculation of the transfer functions of the controllers of the cascaded loops control system, followed by computer simulation using the OrCAD software. The results of simulating a cascaded two loops control system of an ACPF with different types of controllers are presented and analytically compared. It is concluded that it is advisable to use a cascaded two loops control system, containing a voltage control loop and a current control loop. The best results show the simulation when using an aperiodic current controller (A-controller) and a proportional-integral voltage controller (PI-controller). The data obtained serve as the basis for further improvement of the operation of the ACPF by enhancing and optimizing the settings, structure and algorithms of the control system, which, with the selected hardware of power converter unit, will allow the ACPF to perform its functions with a high degree of reliability in an entire range of disturbing and control influences.

Background: Health policy is a set of comprehensive principles and legislations that guide how healthcare should be effectively delivered in the community. Medical schools should prepare students to undertake managerial responsibilities by incorporating health policy in the curriculum to deal with the intricacies of healthcare systems and their clinical roles in their future professional careers. Objective: To examine medical students' perception at a Public University in Malaysia regarding teaching health policy and their participation in health policy roles. Material and Methods: A cross-sectional study using universal sampling was carried out among the medical students using a paper-based questionnaire to collect the data. Results: Most respondents opined their willingness to learn health policy (80.9%) and that teaching health policy (83.6%) should be compulsory for medical students. The respondents thought health policy should be introduced earlier in Year 1 or 2. The student scores on their knowledge regarding health policy and year of study were significantly associated with their involvement in the health policy roles in both the simple and multiple logistic regression. Both statistical tests reported higher participation in health policy roles with the higher year of study, though only Year 4 and 5 were significant in the simple logistic regression and only Year 5 in the multiple logistic regression compared to Year 1. On the other hand, age and type of admission show significant results only in the simple logistic regression, while the race was only significant at the multivariate level. Conclusion: This study demonstrated that most respondents showed their willingness to learn health policy, participate in the health policy programs, and recommend that health policy be considered an essential topic in the medical curriculum, which should be taught right from the first year of medical school. We recommend encouraging students’ participation in health policy activities.

A better understanding of high temperature processes in slags contributes to facilitate knowledge based design of the solidified product. Here, a slag analogue with a nominal composition of 17 wt% LiMnO2 and 83 wt% Ca2SiO4 was synthesized encountering fairly high cooling rates. The Mn species from 1223 K to 1773 K was simulated using a thermodynamic model assuming a homogeneous melt. The micro-composition including the Mn species of the solidified slag was determined experimentally and was used as basis for molecular dynamics (MD) simulation. The MD simulation provides information on structure and viscosity at high temperatures, otherwise difficult to access. These parameters significantly influence oxidation state of redox-active elements and the solidified product. The micro-composition analyzed by electron probe micro analysis (EPMA) and synchrotron based micro-X-ray fluorescence (micro-XRF) showed that Mn-rich and Ca-Si-rich phases are separated. While the Mn-O phases did not contain noticeable Ca, the Ca2SiO4 phase had incorporated 0.6 wt% of Mn. The slag solidified into round shaped and droplet shaped grains of a Li-Mn-oxide, some Mn3O4 and Ca2SiO4. The powder X-ray diffraction (PXRD) confirmed the formation of larnite, the identity of the Li-Mn-oxide however remained inconclusive. The Mn oxidation state (OS) was identified using synchrotron based micro-X-ray absorption near edge spectroscopy (micro-XANES). The Mn-O grains, matched well with Li-Mn-oxides and a Mn OS: +3 e.g. LiMn3+O2. Small areas matching Hausmannite (Mn2+Mn23+O4) were also identified. The OS of Mn in the silicate phase could not be identified. For comparison a slowly cooled slag analogue with similar composition however higher Si content, was also subjected to micro-XANES. The slowly cooled slag formed long Mn-rich needles in a matrix of large calcium silicate crystals. The Mn-rich crystals matched well with the XANES spectrum of a Mn3+ Li-oxide like LiMn3+O2. At the rim of the needles the Mn-spectra matched well the Hausmannite (Mn2+Mn23+O4) reference. In the silicate phases Mn had a OS: +2, unambiguously. The melt structure at different temperatures of two compositions i.e. LiMn3+O2 and Ca2SiO4 was simulated using molecular dynamics (MD). They serve as model compositions assuming a heterogeneous melt. The results show significant different degrees of polymerization and viscosity. Information from MD simulations can support the identification of potentially different oxygen permeability and with that prediction of oxidation states. The bulk composition was identified by inductively coupled plasma optical emission spectrometry (ICP-OES), bulk structure by PXRD and bulk species by lab-XANES. The synchrotron micro analysis including micro-XRD were performed at the microfocus beamline I18 at the Diamond Light Source. Pure reference compounds were prepared and characterized with the same multi-modal approach.

This study considers the values of the credit payments that are made at random values for both payment size and number. The simultaneous existence of the two random variables increases the total value of the volatility of the payment process. The dependence for the simultaneous influence of the two random variables is derived by applying conditional probabilistic formulations. Formal relations apply to animal husbandry credit payments. The credit policy was analyzed for the cases of regular payments and with a stochastic number of payments. A recommendation for the upper level of credit payments is proposed based on a model predictive approach using historical payment data. A credit management algorithm is derived, in which decision-making for credit payments is formally derived and numerically discussed. The application of derived quantitative relations is empirically applied to real data on animal husbandry. The recommendations from the dependencies obtained allow a reduction in the mean values of credit payments, which correspond to a reduction in the credits used for business management, without a change in business policy.

As Alberta increases solar power generation, land use conflicts with agriculture increase. A solution that enables low-carbon electricity generation and continued (in some cases increased) agricultural output is the co-locating of solar photovoltaics and agriculture: agrivoltaics. This study reviews policies that impact the growth of agri-voltaics in Alberta. Solar PV-based electricity generation is governed by three regula-tions based on system capacity. In addition, agrivoltaics falls under various legisla-tions, frameworks, and guidelines for land utilization. These include Land Use Frame-work, Alberta Land Stewardship Act, Municipal Government Act, Special Areas Dis-position, Bill 22 and other laws/policies all of which are reviewed in the context of agrivoltaics. Several policies are recommended to support rapid diffusion of agrivolta-ics. First, open access research into agrivoltaics, which not only will help optimize agrivoltaic systems for the region, but also coupled with public education is expected to galvanize social acceptability of large-scale PV deployment. Clearly defining and categorizing agrivoltaic technology, developing agrivoltaic standards, making agri-voltaic technology-friendly regulations/frameworks and developing programs and pol-icies to incentivize agrivoltaic deployment over conventional PV will all accelerate dif-fusion. Through these measures, Alberta can achieve conservation and sustainability in food and energy sector while simultaneously addressing the renewable energy and climate-related goals.

Rapid search and localization for nuclear sources can be an important aspect in preventing human harm from illicit material in dirty bombs or from contamination. In the case of a single mobile radiation detector, there are numerous challenges to overcome such as weak source intensity, multiple sources, background radiation, and the presence of obstructions, i.e., a non-convex environment. In this work, we investigate the sequential decision making capability of deep reinforcement learning in the nuclear source search context. A novel neural network architecture (RAD-A2C) based on the actor critic (A2C) framework and a particle filter gated recurrent unit for localization is proposed. Performance is studied in a randomized 20 x 20 m convex and non-convex environment across a range of signal-to-noise ratio (SNR)s for a single detector and single source. RAD-A2C performance is compared to both an information-driven controller that uses a bootstrap particle filter and to a gradient search (GS) algorithm. We find that the RAD-A2C has comparable performance to the information-driven controller across SNR in a convex environment and at lower computational complexity per action. The RAD-A2C far outperforms the GS algorithm in the non-convex environment with greater than 95% median completion rate for up to seven obstructions.

This study investigated how different gamification elements in mobile apps influence users' basic psychological needs (autonomy, competence, relatedness) and subsequent engagement outcomes. Survey data was analyzed using PLS-SEM. Social gamification elements enhanced autonomy and competence needs, while immersive elements boosted autonomy and relatedness. Achievement/progression components increased competence and relatedness perceptions. Interestingly, personal traits did not significantly impact psychological needs. Crucially, satisfying autonomy and relatedness predicted higher user satisfaction and continued usage intentions, highlighting their importance for sustained engagement. Competence influenced satisfaction but not continuance intention. The findings demonstrate the motivational roles of distinct gamification features in fostering need-supportive experiences. Designers should incorporate varied social, immersive, and achievement components to address users' psychological requirements holistically. Prioritizing autonomy and relatedness support appears vital for achieving enjoyable, self-motivated, and persistent user engagement across gamified systems and domains. The study provides actionable insights for optimizing motivational affordances through psychologically-informed gamification implementations.

Access to urban green and blue spaces (UGBS) has been associated with positive effects on health and wellbeing; however, the past decades have seen a decline in quality and user satisfaction with UGBS. This reflects the mounting challenges that many UK cities face in providing appropriate public facilities alongside issues such as health inequalities, an ageing population, climate change, and loss of biodiversity. At present, little is known about the preferences of different population subgroups and, specifically, the UGBS they visit and the spaces they avoid. Using a public participatory geographic information system (PPGIS), the overall aim of the research presented here was to investigate the preferences of different population subgroups in urban areas, and the UGBS they visit, using Edinburgh, Scotland as a case study. We created a baseline visitor demographic profile for UGBS use, and highlighted how visitors perceive, physically access, use, and engage with UGBS. The results revealed considerable variation in UGBS preference: one person’s favourite UGBS may be one that someone else dislikes and avoids. It is clear that adapting UGBS to suit local communities should not be a ‘one-size-fits-all’ approach. The conflicting views and preferences of different groups of respondents point to the importance of developing policies and park management plans that can accommodate a variety of uses and experiential qualities within individual parks. PPGIS offers an ideal tool for achieving this

The COVID-19 pandemic crisis has brought about unprecedented economic and social consequences worldwide. The implementation of isolation measures, including national and international travel restrictions, significantly affected contact-intensive sectors such as tourism. During this lockdown period, Information and Communication Technology (ICT) was crucial in maintaining connectivity and enabling remote activities. Governments across the world implemented discretionary measures to mitigate the crisis's adverse effects on economic activity. This paper aims to analyze whether the level of ICT adoption and the importance of tourism influence the fiscal policy efforts pursued by governments. Based on the results of a linear regression analysis for 154 countries, the findings suggest that in countries with higher international tourism receipts, the governments had to promote higher fiscal stimulus. At the same time, ICT development diminished the efforts of the fiscal policy response to the crisis since it facilitated economic resilience. The findings of this study can contribute to understanding how governments responded to the pandemic crisis and the factors that influenced their fiscal policy decisions.

The aim of this article is to present the course of the COVID-19 pandemic in Poland in 2020-2022, the formation of ad hoc health and anti-crisis policies, an assessment of crisis management and the perceived impact of the pandemic and anti-crisis measures.The paper draws on literature, official reports on the pandemic, data from Eurostat and other information from state institutions and public organisations.Particular attention was paid to the analysis and evaluation of the objectives, instruments and effects of the policies pursued by the state in a coordinated manner, i.e. the anti-pandemic policy and the anti-crisis policy. The anti-pandemic policy in Poland has failed to protect the country from significant personal losses and negative impacts on the health of the population and demographic processes.The anti-crisis policy of the state carried out with the mobilisation of businesses and disciplined society, in the form of anti-crisis shields supplemented and adjusted on an ongoing basis, allowed Poland to avoid a deep crisis and economic recession. Attention was drawn to the need to coordinate the management of health and economic crises nationally and internationally, and to the need to have a medium-term anti-crisis state strategy and a system for the early detection of crisis symptoms.

In this study, we employ the GARCH-MIDAS (Generalised Autoregressive Conditional Heteroskedasticity variant of Mixed Data Sampling) model to explore the predictability of commodity return volatility in relation to US climate policy uncertainty (CPU). Our analysis utilizes the 20-day annualized realized commodity volatility returns of nine global commodities (Aluminium, Cocoa, Coffee, Copper, Cotton, Rice, Soybean, Sugar, and Wheat) to construct the GARCH-MIDAS model, with Climate Policy Uncertainty (CPU) serving as the predictive variable. The outcomes of our investigation reveal a consistently positive and statistically significant relationship between CPU and the selected commodities. This implies that CPU effectively serves as a robust predictor of volatility in commodity returns. The implications drawn from our results suggest that climate change policies play a pivotal role in influencing economic activities within the commodity market. This underscores the substantial impact of climate change considerations on investment decisions and further emphasizes the integral role of climate change in shaping economic choices.

In 2021 an acute energy crisis inflicted severe damage on the global economy, leading to escalated prices for electricity, gas, and fuel. In order to shield individuals and businesses from the mounting energy expenses, governments have been compelled to implement policy measures, including tax reductions, price restrictions or discounts, and subsidies. This research paper examines these policy responses through the lens of energy sufficiency. Energy poverty poses a significant threat to social cohesion and support for climate-related initiatives. Therefore, it is imperative to employ compensatory measures. However, the design of such solutions must carefully consider the incentives to reduce energy consumption and associated carbon emissions. The findings of the analysis demonstrate that the escalation of energy costs holds promise for achieving energy sufficiency. Nevertheless, the government's response to the surge in energy prices and energy poverty falls short and lacks precision. Most of the policy changes primarily focus on regressive energy cost subsidies and nudging households away from fossil fuels, but they fail to generate the necessary impetus for achieving energy sufficiency, which involves the elimination of energy poverty and excessive energy consumption.