Polyvinyl chloride (PVC) electric wires were subjected to dechlorination in subcritical water at three different temperatures in a high-pressure reactor. About 2.09, 73.08 and 95.96 wt. % of chlorine in PVC wires was removed during dechlorination at 200, 250 and 300 °C, respectively. The solid residues were analyzed and characterized by thermogravimetry, at three different heating rates (5, 10 and 20 °C/min) in inert and oxidizing atmosphere. With the purpose of studying the emission of chlorinated pollutants, pyrolysis experiments at 850 °C were also performed in a laboratory scale reactor with the dechlorinated materials, as well as with the original PVC electric wire. Polycyclic aromatic hydrocarbons (PAH) formation increased, but chlorobenzenes (ClBz) and chlorophenols (ClPh) formation decreased as the temperature of dechlorination increased; naphthalene was the most abundant PAH and monochlorobenzene and monochlorinated phenols (3-+4-) were the most abundant chlorinated compounds.

PVC-based materials are bad in terms of biodegradability. To enhance the ecological property of such materials, the fabrication of PVC-based composites using biofillers with acceptable performance characteristics could be considered. In this work, plant-filled PVC-based composite materials were obtained and study their optical, structural, thermal, and mechanical properties depending on the nature of the filler (spruce flour, birch flour, and rice husk) were studied. Increasing the proportion of plant filler somewhat reduces the strength characteristics and reduces the flexibility of the samples. But samples with plant filler allows them to be used at low temperatures without changing the operating characteristics. Some of the fillers affected the thermal stability of composites by increasing their thermal decomposition resistance. So, results have shown that plant-filled polymer composites based on PVC can be used on an equal basis with unfilled PVC plastic compound for some applications such as construction.

In order to assess the human exposure risks from the release of contaminants from water pipes made of polyvinyl chloride (PVC), experiments were carried out by subjecting the PVC pipe material to burning and leaching conditions followed by analysis of the emission and leachate samples. The emissions of burning pipes were analyzed by both infrared spectrometry and gas chromatography-mass spectrometry (GC-MS). The emission results indicate the presence of chlorinated components including chlorine dioxide, methyl chloride, methylene chloride, allyl chloride, vinyl chloride, ethyl chloride, 1-chlorobutane, tetrachloroethylene, chlorobenzene, and hydrogen chloride were detected in the emissions of burning PVC pipes. Furthermore, the concentrations of benzene, 1,3-butadiene, methyl methacrylate, carbon monoxide, acrolein, and formaldehyde were found at levels capable of affecting human health adversely. The analysis of PVC pipe leachates using GC-MS shows that there are 40-60 tentatively identified compounds, mostly long-chain hydrocarbons such as tetradecane, hexadecane, octadecane, and docosane, were released when the burned PVC materials were soaked in deionized water for one week. Quantitative analysis shows that 2-butoxyethanol, 2-ethyl-1-hexanol, and diethyl phthalate were found in the burned PVC polymer at the average levels of 2.7, 14.0, and 3.1 micrograms per gram (g/g) of pipe material. This study has significant implications for understanding the benzene contamination of drinking water in the aftermath of wildfires that burned polymer pipes in California.

The structure and physicochemical properties of polyvinyl alcohol (PVA) and PVA/glycerol films have been investigated by Fourier-transform infrared spectroscopy (FT-IR), X-ray Diffraction (XRD), thermogravimetry/differential thermal analysis (TG/DTA), and advanced scanning probe microscopy (SPM). In the pure PVA films, SPM allowed us to observe ribbon-shaped domains with a different frictional and elastic contrast, which apparently originated from a correlated growth or assembly of PVA crystalline nuclei located within individual PVA clusters. The incorporation of 1.0 wt.% glycerol led to modification in shape of those domains from ribbon-like in pure PVA to rounded in PVA/glycerol 1.0 wt.% films; changes in the relative intensities of the XRD peaks and a decrease of the amorphous halo in the XRD pattern were also detected, while the DTA peak corresponding to the melting point remained at almost the same temperature. For higher glycerol content, FT-IR revealed additional glycerol-characteristic peaks presumably related to the formation of glycerol aggregates, and XRD, FT-IR, and DTA all indicated a reduction in crystallinity. For more than 2.0 wt.% glycerol, the plasticization of the films complicated the acquisition of SPM images without tip-induced surface modification. Our study contributes to the understanding of crystallinity in PVA and how it is altered by a plasticizer such as glycerol.

Pyrolyzed organic matter – commonly referred to as biochar – generally has positive effects on plant growth and can enhance early seedling development. Biochar-based seed coatings may thus be beneficial, specifically under adverse soil conditions such as high soil salinity. We evaluated germination and early plant development in radish (Raphinus sativa) seeds coated with conifer-feedstock slow-pyrolysis biochar; following the precedent of prior studies, polyvinyl acetate (PVAc) was used as the binding agent. Biochar-based seed coatings reduced germination rates and radicle extension in Petri dish trials; however, leaching of coated seeds largely eliminated this effect. PVAc applied in solution inhibited seed germination to a similar extent, suggesting that toxicity of PVAc or chemical products derived from it is the main mechanism for germination inhibition; a meta-analysis of published literature also indicates negative effects of biochar-based seed coatings using PVAc. In greenhouse trials the same biochar seed coatings improved aspects of plant growth and physiological status relative to controls, specifically enhancing root development. We conclude that biochar-based seed coatings have promise in promoting early seedling growth, and in combating salinity stress in agronomic and restoration applications. However, our findings contraindicate PVAc use as a binding agent. Further research is needed to test non-phytotoxic, readily biodegradable binding agents and to optimize biochars and seed coating processes for specific applications in agronomy and ecological restoration.

Adult neurogenesis involves generation of functional neurons from neural progenitor cells, which have the potential to complement and restore damaged neurons and neural circuits. Therefore, the development of drugs that stimulate neurogenesis represents a promising strategy in stem cell therapy and neural regeneration, greatly facilitating the reconstruction of neural circuits in cases of neurodegeneration and brain injury. Our study reveals that compound A5, previously designed and synthesized by our team, exhibits remarkable neuritogenic activities, effectively inducing neurogenesis in neural stem/progenitor cells (NSPCs). Subsequently, transcriptome analysis using high-throughput Illumina RNA-seq technology was performed to further elucidate the underlying molecular mechanisms by which compound A5 promotes neurogenesis. Notably, comparative transcriptome analysis showed that the up-regulated genes were mainly associated with neurogenesis and the down-regulated genes were mainly concerned with cell cycle progression. Furthermore, we confirmed that compound A5 significantly affected the expression of transcription factors related to neurogenesis and cell cycle regulatory proteins. Collectively, these findings identify a new compound with neurogenic activity and may provide insights into drug discovery for neural repair and regeneration.

The pursuit of an environmentally sustainable manufacturing process advocates for the substitution of harmful reagents for less damaging and recyclable solutions. This study aims to assess the effectiveness of using cellulose microfibrils synthesized via different hydrolysis reactions as reinforcing agents in polyvinyl alcohol (PVA) at varying con-centrations. The investigation explores the morphology, thermal properties, and chemi-cal behavior of the cellulose particles. The cellulose microfibrils (CMF) produced using citric acid exhibited the highest yield and aspect ratio. Notably, particles from organic acids demonstrated greater thermal stability, with oxalic acid-derived particles displaying the maximum thermal degrada-tion temperature. Subsequently, cast films of PVA reinforced with the cellulose microfibrils underwent comprehensive analyses, including Fourier transfer infrared (FTIR) spectroscopy, thermal degradation temperature (Td), differential scanning calorimetry (DSC), and tensile strength tests. The thermal behavior of cast films experienced notable changes with the addition of cellulose particles, evidenced by increased melting and crystallinity temperatures, along with a rise in the degree of crystallinity. The incorporation of cellulose particles led to a substantial improvement in mechanical properties. Films containing CMF dis-played higher Young’s modulus, and the sample incorporating 5% CMF derived from citric acid exhibited the most significant increase in modulus.

Polyvinyl guanidineacetic (PVG) was prepared by the chemical grafting between poly(vinyl alcohol) (PVA) and guanidineacetic acid. The results showed that the guanidineacetic groups were successfully introduced into the polyvinyl alcohol by fourier transform infrared (FTIR) and thermogravimetry (TG). The effects of the amount of catalyst and reaction time on the PVG grafting rate were investigated. The PVG/NWF composite membrane as a heterogeneous catalyst for biodiesel production was successfully prepared by the solvent phase inversion. The effects of mass ratio of methanol/soybean oil and reaction temperature on the conversions using the composite membrane for transesterification were studied. And the reusability of the composite membrane and the kinetics of the reaction catalyzed by the composite membrane were also investigated. The conversions obtained from the model are in good agreement with the experimental data.

The design of an antimicrobial coating materials becomes ideal in order to prevent infections caused by the transmision of pathogens coming from human’s contact with contaminated surfaces. In that aim layered single hydroxides (LSH) and layered double hydroxides (LDH) containing Zn and Cu, in nitrate form and intercalated with antimicrobial molecules, were synthe-sized and characterized. Cinnamate and salicylate anions were chosen to be intercalated in the fillers because of their well known antimicrobial activity. Several coatings based on polyvinyl alcohol (PVA) and LDH or LSH with increasing amounts of filler were prepared and filmed on a polyethylene terephthalate (PET) substrate. Coatings were characterized and their antimi-crobial activity was evaluated against pathogens critical in nosocomial infections, giving interesting results.

A good optical quality crystal of 2-aminopyridine (2AP) metal complex crystals was grown by slow evaporation technique at room temperature. The transparent and defect less bulk size of 2-aminopyridine potassium dihydrogen orthophosphate metal complex crystals have been grown by solution growth method. The molecular structure and morphology of grown crystals was drawn and planes are indexed using WINXMORPH software. A optical absorption spectrum, the UV cut-off wavelength, Band gap (Eg), Reflectance (R), Refractive Index (n), Extinction coefficient (K) and Electrical susceptibility (χc) are calculated for 2AP metal complex crystals.

Abstract: This study aims to analyze the physico-mechanical properties and dynamic models of tissue-simulating hydrogels, specifically the photoacoustic (PA) response signals, by varying the concentrations of polyvinyl alcohol (PVA) and molecular weight (MW). A state space model (SSM) is proposed to study the PVA hydrogels to retrieve the PA-related signal's damping ratio and nat-ural frequency. Nine box-shaped PVA hydrogels containing saline solution were used, with five concentrations of PVA (7, 9, 12, 15, 20%) for MW1 and four for MW2. The results indicated that the concentration of PVA and MW played an important role in the PA wave's amplitude, arrival time, and speed of sound over the hydrogels. The SSM parameters showed that increasing PVA and MW concentrations improved the hydrogels' ability to absorb and transfer energy under the PA effect. These parameters were also found to be correlated with density and modulus of elasticity. Addi-tionally, the concentrations of PVA and MW affected the absorption and optical scattering coeffi-cients. The physical-mechanical properties, including porosity, density, and modulus of elasticity, improved as the concentration of PVA and MW increased. The ultimate goal of this study is to develop hydrogels as phantoms that can be used for tissue simulation and imaging.

Nanoporous membranes promise energy-efficient water desalination. Hexagonal boron nitride (h-BN), like graphene, exhibits outstanding physical and chemical properties, making it a promising candidate for water treatment. We employed Car–Parrinello molecular dynamics simulations to establish accurate modeling of Na+ and Cl- permeation through hydrogen passivated nanopores in graphene and h-BN membranes. In these complex systems the classical potentials cannot properly account for the physics at play. We demonstrate that ion separation works well for the h-BN by imposing a barrier of 0.13 eV and 0.24 eV for Na+ and Cl- permeation respectively, compared to the graphene where the Cl- ion faces a negative barrier of 0.68 eV and is prone toward blockade and Na+ permeation is associated with a slightly negative barrier of 0.03 eV. From the change in the solvation shell, we get the following trend: Na/h-BN > Na/G > Cl/G > Cl/h-BN. We argue that the trend in the permeation barrier changes to Cl-h-BN > Na-h-BN > Na-G > Cl-G due to a combination of several interactions, including the distortion of the water network induced by the ions, the ion-water interaction, and the ion-nanopore interaction. Overall, the desalination performance of h-BN surpasses that of their graphene counterparts.

Polyvinyl Alcohol (PVA)/ Graphene Quantum Dots (GQDs) polymer nanocomposite films have been prepared, and the relationship between their structural, thermal and nanoscale morphologi-cal properties, and their photoluminescent response, has been investigated. Although according to X-ray Diffraction (XRD), Fourier-Transform Infrared Spectroscopy (FT-IR) and Differential Thermal Analysis (DTA) the incorporation of GQDs does not significantly affect the percentage crystallinity of the PVA matrix, for a range of added GQD concentrations, Atomic Force Micros-copy (AFM) showed the formation of islands with apparent crystalline morphology on the surface of the PVA/GQD films, with GQD presumably acting as a nucleating agent for island growth. The incorporation of GQD also led to the formation of characteristic surface pores with increased stiffness and frictional contrast, according to Ultrasonic Force Microscopy (UFM) and Frictional Force Microscopy (FFM) data. The photoluminescence (PL) spectra of the films were found to de-pend both on the amount of GQD incorporated and on the film morphology. For GQD loads > 1,2wt%, a GQD-related band was observed at ~ 1650 cm-1 in FT-IR, along with an increase in the PL band at lower energy. For a load of ~2wt% GQD, the surface morphology was characterized by extended cluster aggregates with lower stiffness and friction than the surrounding matrix, and the PL signal decreased.

Within the context of sustainable material development for the construction sector, this study explores the viability of panels composed of recycled newspaper-derived cellulose (9%), rice husk (14%), borax (15%), and polyvinyl acetate-based glue (62%). The methods employed involve water absorption and density tests, following ASTM C-1763 and C-303 standards. The fire resistance test conforming to the European standard UNE 23-725-90, and a mold growth test using AOAC 2002.11. The composite is prone to absorbing a significant amount of water when exposed to humid conditions. However, the incorporation of rice husk and borax can provide benefits such as improved moisture resistance compared to other cellulitic insulators, which may be advantageous in specific climates. Also, the developed composite has an intermediate density compared to other polymeric materials. This characteristic presents advantages in applications that demand a balance between strength and lightness. During the fire resistance tests, the samples with borax presented less fire propagation, and superficial damage compared with the specimens without borax. This is important, considering the fireproofing property, required in building materials. The presence of borax in the composite has an inhibitory effect on the growth of fungi and yeasts. These findings are consistent with previous research. Nevertheless, further research and testing are imperative to assess its viability and performance for commercial applications.

This article discusses the fabrication of pullulan/polyvinyl alcohol (PVA) and PVA blends as carrier polymers for drug delivery. This study utilized coaxial electrospinning to encapsulate doxorubicin (DOX), a common anticancer drug, within nanofibers, which helped mitigate the adverse effects of DOX on normal cells. The study also demonstrated that the coaxial electrospinning technique using PVA/pullulan cores was effective in inhibiting the attachment and proliferation of HeLa cells, a type of cervical cancer cell. The use of pullulan/PVA and PVA blends as carrier polymers in conjunction with coaxial electrospinning could provide a safe and effective drug delivery system for the treatment of cervical and other solid malignancies. The study concluded that nanofibers showed promising results in inhibiting the growth of HeLa cells, indicating their potential as safe and effective drug delivery systems for treating cervical cancer and other solid malignant tumors.

The corrosion inhibition behavior of cetyl pyridinium chloride (CPC) on mild steel (MS) in 0.5 M H₂SO₄ solution was examined using the weight loss method and potentiodynamic polarization method. The experimented MS surface was characterized by Fourier Transform Infrared Spectroscopy (FTIR), Field Emission Scanning Electron Microscopy (FESEM), and Atomic Force Microscopy (AFM). Corrosion rate and corrosion efficiency was calsulated via weight loss and potentiodynamic polarization methods where the corrosion rate in 0.5 M H₂SO₄ , 0.000192 M, and 0.0077 M of CPC solution was 12.09×10^-3, 8.23×10^-3, 6.63×10^-5 (mm/Year), respectively and the inhibition efficiency of 94.42% and 98.54%. FESEM studies demonstrated the corrosion attack on MS surface. Also, the EDX showed the presence of nitrogen of CPC. Thus, CPC acts as an important corrosion inhibitor.

Vinyltriethoxysilane (VTES) was covalently bonded onto graphene oxide. Several methods, including X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and X-ray diffraction, were used to demonstrate the presence of VTES on the surface of graphene oxide and the creation of this covalent link. Following that, different quantities of the resultant vinyltriethoxysilane functionalized graphene oxide (VTESFGO) were mixed with polyvinyl alcohol (PVA) to form VTESFGO/PVA nanocomposite films (NCFs) with a 3-dimensional network structure. The creation of these NCFs and the presence of a three-dimensional network were confirmed by Fourier transform infrared spectroscopy. The three-dimensional network structure provided these NCFs extraordinary characteristics. The mechanical and thermal stability, oxygen transfer rate (OTR), and water resistance pressure (WRP) of the NCFs were investigated. The nanocomposite film (NCF) with the highest weight percentage of VTESFGO (3.0 wt.%) was 47.5% more thermally stable than pure PVA, with an oxygen transmission rate of 0.3 cm3/m2 per day and a water resistance pressure of 780 mm/cm2. However, as the weight percentage of VTESFGO increased, the mechanical strength of the NCFs decreased as a result of silanol self-condensation, resulting in particulate formation, as confirmed by scanning electron microscopy.

Since electrical resistivity of concrete can be measured in a more rapid and simple way than chloride diffusivity, it should be primarily regular quality control of the electrical resistivity of concrete which provides the basis for indirect of quality control of concrete durability during the concrete construction. If this is realized, the electrical resistivity of concrete can be a crucial parameter to establish maintenance strategy for marine concrete structures. Electrical resistivity of concrete is important to estimate two processes involved in corrosion of reinforcement: initiation (chloride penetration) and propagation (corrosion rate). The resistivity of concrete structure exposed to chloride indicates the risk of early corrosion damage, because a low resistivity is related to rapid chloride penetration and to high corrosion rate. Concrete resistivity is a geometry-independent material property that describes the electrical resistance, which is the ratio between applied voltage and resulting current in a unit cell. The current is carried by ions dissolved in the pore liquid. While some data exist on the relationship between moisture content on electrical resistivity of concrete, very little research has been conducted to evaluate the effect of chloride on the conduction of electricity through concrete. The purpose of this study is to examine and quantify the effect of pore water and chloride content on surface electrical resistivity measurement of concrete. It was obvious that chloride content had influenced the resistivity of concrete and the relationship showed a linear function. That is, concrete with chloride ions had a comparatively lower resistivity. Chloride can lead to underestimate the electrical resistivity of concrete. Conclusively, this paper suggested the quantitative solution to depict the electrical resistivity of concrete with various chloride contents.

In this study, literature on pore structure and chloride ion diffusivity was collected to investigate the correlation of pore structure indicators with diffusivity. Good correlation between total porosity and chloride ion diffusivity was found when the samples did not contain admixture materials and diffusion test was conducted without acceleration. Pore diameter indicators did not correlate with diffusivity. The diffusivity of cement paste was reduced by admixture materials compared to that without admixture materials even if the total porosity is the same. On the other hand, the diffusivity of concrete was not reduced by admixture materials.

Repair mortar is commonly used to rehabilitate reinforced concrete structures or components that exhibit a relatively high level of distresses. Yet, this repair mortar can be contaminated by salt from its service environment. This work employs a two-dimensional finite element model to investigate the transport behavior of ionic species in salt-contaminated and water-saturated repair mortar under an externally applied electric field. The model was experimentally validated and then utilized to evaluate the effectiveness of electrochemical chloride extraction (ECE) with or without electrical injection of corrosion inhibitor (EICI). In the case study, both the ECE alone and the ECE+EICI treatment was found effective in decontaminating the zone in front of the steel rebar. In both techniques, the magnitude of current density has a significant effect on removing chloride out of the mortar and increasing the pH of the pore solution near the rebar, whereas the treatment time any not have a significant effect under some scenarios. The injection of the organic corrosion inhibitor significantly slowed down the removal of chloride. Changes in the ionic distribution in the mortar were generally beneficial in reducing the corrosion risk of the steel rebar and thus extending the service life of the repair mortar.

Herein, the mechanical properties and carbonation durability of engineered cementitious composites (ECC) were studied. For cost-efficient utilization of ECC materials, polypropylene (PP) and hydrophilic polyvinyl alcohol (PVA) fibers were employed to cast different types of specimens. The compressive strength, Poisson’s ratio, strength-deflection curves, cracking/post-cracking strength, impact index, and tensile strain-stress curves of the two types of ECC materials, with different fiber contents of 0 vol%, 1 vol%, 1.5 vol% and 2 vol%, were investigated by conducting compressive tests, four-point bending tests, drop weight tests, and uniaxial tensile tests. In addition, the matrix microstructure and failure morphology of the fiber in the ECC materials were studied by scanning electron microscopy (SEM) analysis. Furthermore, carbonation test and steel corrosion after carbonization were employed to study durability resistance. The results indicated that for both PP fiber- and hydrophilic PVA fiber-reinforced ECCs, the compressive strength first increases and then decreases as fiber content increases from 0 vol% to 2 vol% and reaches the maximum at 1 vol% fiber content. The bending strength, deformation capacity, and impact resistance show significant improvement with increasing fiber contents. The ECC material reinforced with 2 vol% PP fiber shows superior carbonized durability with maximum carbonation depth of only 0.8 mm.

In order to design effective protective coatings against corrosion, the polyvinyl alcohol (PVA) as compound and composite with silver nanoparticles (nAg/PVA) were electrodeposited on copper surface employing electrochemical techniques such as linear potentiometry and cyclic voltammetry. A new paradigm was used to distinguish the features of coatings, i.e., a Deep Convolutional Neural Network (CNN) was implemented to automatically and hierarchically extract the discriminative characteristics from the information given by optical microscopy images. The main arguments that invoke a CNN implementation in the surface science of materials are the following: artificial intelligence techniques can be successfully applied to learn differences between surface coatings; based on their popularity for image processing, CNN can model images related to the problem of coatings; deep learning is able to extract the features that are distinguishable between material surfaces. To provide an overview of the copper surface, CNN was applied on microscope slides (CNN@microscopy) and inherently learnt distinctive characteristics for each class of surface morphology. The material surface morphology controlled by CNN without the interference of the human factor was successfully conducted, in our study, to extract the similarities/differences between unprotected and protected surfaces to establish the PVA and nAg/PVA performance to retard the copper corrosion.

As a hazardous waste, pickling waste liquor must be properly treated. An alternative consists in promoting the formation of ferrous salts from this residue, due to its higher ferrous content. Since FeCl2·4H2O is widely used in several applications, obtaining pure crystals of this material appears to be an interesting prospect. However, this compound has scarcely been investigated. In the present work, FeCl2·4H2O crystals have been obtained from pickling waste liquors. Their structural and morphological characteristics have been investigated by X-ray diffraction, scanning electron microscopy as well as Mössbauer spectroscopy. In addition, the photoluminescence study of the obtained samples was also assessed. It was observed that after some aging time, the obtained crystals change in colour from green to more yellowish. So, the aged sample has also been evaluated, and their structural characteristics are compared with the original crystals. Despite this, the obtained crystals exhibit a FeCl2·4H2O structure, which is not modified with the aging of the sample.

Chloride (Cl-) is applied in coffee in rates as a “macronutrient” due that potassium (K+) is one of the most demanded nutrients by the coffee plant, and the potassium muriate (KCl) bases fertilizer is one the most used by the coffee growers. Does not exist scientific evidence that addresses the question regarding with which is the influences of the Cl- applied in the K fertilization base on MOP on coffee growth, nutrient uptake, and nitrogen use efficiency (NUE). Over four years, two trials were conducted on greenhouse and field conditions to address these questions. The trials set up were designed to test the influence of increased Cl- and reduced S rates on biomass accumulation, nutrient uptake, and NUE. A significant effect of the Cl- rates on growth was observed under greenhouse conditions but a non-significant effect on yield under field conditions. Cl- and S significantly influence the NUE in coffee. The result allows us to conclude that Cl- rates need to be balanced with S rates and that Cl- applied as a macronutrient can improve the NUE in coffee when those rates do not exceed 180 mg. L-1 Cl- and 80 mg.L-1 S in the greenhouse and 150 kg.ha-1.year-1 Cl- and 50 kg. ha-1.year-1 S in field conditions. In practical terms, coffee farmers need to balance the K base fertilizers sources to improve the nutrient use efficiency, especially the NUE.

The SLC12 family of cation-chloride-cotransporters (CCCs), comprising potassium chloride cotransporters (KCCs)-mediated Cl- extrusion relative to sodium chloride cotransporters (NKCCs)-mediated Cl- loading, play vital roles in cell volume regulation and ion homeostasis. These functions of the CCCs influence a variety of physiological processes, many of which overlap with the pathophysiology of cardiovascular disease. Although not all of the cotransporters have been linked to Mendelian genetic disorders, recent studies have provided new insights into their functional role in vascular and renal cells along with their contribution to cardiovascular diseases. Particularly, an imbalance in potassium levels promote the pathogenesis of atherosclerosis and disturbances in sodium homeostasis are one of the causes of hypertension. Recent findings even suggest hypothalamic signalling as a key signalling pathway in the pathophysiology of hypertension. In this review, we summarize and discuss the role of CCCs in cardiovascular disease with particular emphasis on knowledge gained in recent years on NKCCs and KCCs.

It is known that ammonium has a higher permeability through anion-exchange and bipolar membranes compared to K+ cation that has the same mobility in water. However, the mechanism of this high permeability is not clear enough. We develop a mathematical model based of the Nernst-Planck and Poisson equations for diffusion of ammonium chloride through an anion-exchange membrane; proton exchange reactions between ammonium, water and ammonia are taken into account. It is assumed that ammonium, chloride and OH− ions can only pass through membrane hydrophilic pores, while ammonia can also dissolve in membrane matrix fragments not containing water and diffuse through these fragments. It is found that due to the Donnan exclusion of H+ ions as coions, the pH in the membrane internal solution increases when approaching the membrane side facing distilled water. Consequently, there is a change in the principal nitrogen-atom carrier in the membrane: in the part close to the side facing the feed NH4Cl solution (pH<8.8), it is the NH4+ cation, and in the part close to distilled water, NH3 molecules. The concentration of NH4+ reaches almost zero at a point close to the middle of the membrane cross-section, which approximately halves the effective thickness of the diffusion layer for the transport of this ion. When NH3 takes over the nitrogen transport, it only needs to pass through the other half of the membrane. Leaving the membrane, it captures an H+ ion from water, and the released OH− goes towards the membrane side facing the feed solution to meet the NH4+ ions. The comparison of the simulation with experiment shows a satisfactory agreement.

Anthocyanins extract from purple tomato (PTA) was incorporated with polyvinyl alcohol (PVA) so that a series of colorimetric films of PVA/PTA (based on PVA) were prepared. The role of anthocyanin on color response, FTIR, thickness, water content, mechanical properties, antioxidant activity, and permeation of water vapor through the films was examined. In addition, its application in smart packaging to assess the freshness of shrimp was studied. It was found that the tensile strength, contact angle and WVP of PVA/PTA films increases with the addition of more PTA, while the elongation at break and water content decreased. FTIR analysis showed that there are interactions between PTA and PVA matrix. The addition of anthocyanins caused to a significant improvement for the antioxidant properties of PVA films. Furthermore, the total volatile alkaline nitrogen (TVB-N), total plate count (TPC) and pH value of shrimp were monitored after 4 days of refrigeration, and the color change of the indexes was recorded. The PVA/PTA films changed color from purple to yellow-green during the storage time of 0-4d for shrimp, this suggests that the film could be used in smart packaging as a real-time freshness indicator for shrimp.

This paper presents a proof-of-concept study on the biocolonization of 3D-printed hydroxyapatite scaffolds with mesenchymal stem cells (MSCs). Three-dimensional (3D) printed biomimetic bone structure made of Calcium Deficient HydroxyApatite (CDHA) intended as future bone graft was made from newly developed composite material for FDM printing. The biopolymer polyvinyl alcohol serves in this material as a thermoplastic binder for 3D molding of the printed object with a passive function and is completely removed during sintering. The study presents the material, the process of fused deposition modeling (FDM) of CDHA scaffolds and its post-processing at three temperatures (1200, 1300, 1400 °C), as well it evaluates the cytotoxicity and biocompatibility of scaffolds with MTT and LDH release assays after 14 days. The study also includes a morphological evaluation of the cellular colonization with scanning electron microscopy (SEM) in two different filament orientations (rectilinear and gyroid). The results of the MTT assay showed that the tested material was not toxic, and cells were preserved in both orientations, with most cells present on the material fired at 1300°C. Results of the LDH release assay showed a slight increase in LDH leakage from all samples. Visual evaluation of SEM confirmed the ideal post-processing temperature of the 3D-printed FDM framework for samples fired at 1300°C and 1400°C, with a porosity of 0.3 mm between filaments. In conclusion, the presented fabrication and colonization of CDHA scaffolds have great potential to be used in the tissue engineering of bones.

In this study, multilayer composite nanofiber membranes of sodium alginate (SA) /polyethyleneimine (PEI)/polyvinyl alcohol (PVA) was fabricated via electrospinning technique to enhance the adsorption of Cu2+ from wastewater. The preparation and adsorption mechanisms of the SA/PEI/PVA nanofiber membranes were analyzed by utilizing analytical techniques such as SEM, FTIR, EDS, UV-vis, XRD, and TG. The obtained nanofiber membrane characterized by small diameter, high uniformity, and extensive surface area, demonstrate significant potential for heavy metal ion filtration. Optimal spinning parameters were identified, including a voltage of 19.5 KV, a distance of 8 cm, and specific mass ratios (SA: PEI: PVA, 1:2:6) and injection speeds (8 μL/min) and. The resulting nanofibers with an average diameter of 112.5 nm exhibited excellent morphology and high efficiency, retaining over 85% adsorption capacity for Cu2+ in initial tests and maintaining above 80% efficacy through four successive filtration cycles.

A field study was conducted at the Eastern Mediterranean Agricultural Research Institute, Adana, Turkey, during the 2022/23 cropping seasons to examine the impact of Mepiquat chloride dosage applied at different intervals to optimize growth, yield characteristics enhancement and improve fiber quality attributes of cotton. The study employed a split-split plot design with three replications. The results revealed that differences among treatments were not statistically significant for most parameters investigated. The observed discrepancies indicated that all treatments tested in 2012 delayed cotton development, whereas in 2023, they led to premium fibers. In 2023, the fiber percentage was highest in the control treatment, and in 2022, it was highest at 400 mL·ha-1. Across all years, the Selin variety exhibited the highest fiber percentage when Mepiquat chloride was applied at the bolling stage. The shoot-root ratio was highest at 400 mL·ha-1 during harvest in 2022 and at 0 mL·ha-1 during the reproductive stage in 2023. Overall, the results demonstrated that the application of Mepiquat chloride altered the physiological characteristics of the cotton plants, leading to bottom-up effects on cotton performance. This implies that the effectiveness of Mepiquat chloride in cotton production to alleviate drought stress is influenced by weather-related conditions.

The application possibilities of austenitic stainless steels in high friction, abrasion and sliding wear conditions are limited by their inadequate hardness and tribological characteristics. In order to improve these properties, thermochemical treatment of their surface by plasma nitriding is suitable. This article is focused on corrosion resistance of the conventionally plasma nitrided AISI 304 stainless steel (530 °C, 24 hours) in 0.05 M and 0.5 M sodium chloride solutions at room temperature (20 ± 3 °C), tested by potentiodynamic polarization and electrochemical impedance spectroscopy. The optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy are used for the nitrided layer characterization. The experiment results point to a significant reduction in corrosion resistance after performed plasma nitriding even in a solution with a very low chloride concentration (0.05 mol/L).

The present study concerns the application of electrochemical chloride extraction to concrete designed with partial replacements of Ordinary Portland Cement (OPC) from different binders, namely ground granulated blast furnace (GGBS), pulverized fly ash (PFA) and Silica Fume (SF), to attend the need of corrosion repair for modern constructions. Electrochemical Chloride Extraction (ECE) was applied to the specimens at a current density of 2A/m2 for 4 weeks. The chloride types and binding mechanisms appeared to have important implications on the different performance of treatment perceived for all binders. Considering total chlorides, removal was more significant for OPC and GGBS when compared to others. The main difference noted was that for GGBS the removal of bound chlorides was more significant due to a possible release of adsorbed chlorides from the silicate hydrates, present at higher intensities in this case. However, even though GGBS had greater rates of bound chloride removal it had still the same percentage as OPC for total efficiency due to the fact that in OPC the removal of free chlorides is more expressive.

Biocidal compositions based on interpolyelectrolyte complexes and a low molecular weight antibiotic can become a promising material for creating biocidal coatings, as they combine wash-off resistance and dual biocidal action due to the biocide and the polycation. Molecular mass characteristics of polymers play essential role in physics and mechanical properties of the coatings. In this work, the properties of polydiallyldimethylammonium chloride (PDADMAC) coatings of various molecular weights are investigated and assumptions are made about the optimal molecular weight needed to create antibacterial compositions. To study the resistance to washing off and moisture saturation of the coatings, the gravimetric method was used, the adhesive properties of the coatings were studied by dynamometry. It has been established that an increase in molecular weight affects the wash-off resistance of coatings, but does not affect moisture absorption and adhesion mechanics of coatings. All samples of PDADMAC were demonstrated to exhibit the same antibacterial activity. Thus, when developing systems for creating antibacterial coatings, it must be taken into account that in order to create stable coatings. The requirement to use PDADMAC with a high degree of polymerization is necessary for control the desorption of coating during wash off-but not mandatory for the control of mechanical and antibacterial properties of the coating.

The corrosion morphology in grade 2205 duplex stainless steel wire has been studied to understand the nature of pitting and the causes of the ferrite phase's selective corrosion in acidic NaCl solution. It is shown that the corrosion mechanism is always pitting, which either manifests lacy cover perforation or densely-arrayed selective cavities developing on the ferrite phase. Pits with a lacy metal cover form in concentrated chloride solutions, whereas the ferrite phase's selective corrosion develops in diluted electrolytes, showing dependency on the chloride-ion concentration. The pit perforation is probabilistic and occurs on both austenite and ferrite grains. The lacy metal covers collapse in concentrated solutions but remain intact in diluted electrolytes. The collapse of the lacy metal cover happens due to hydrogen embrittlement. Pit evolution is deterministic and occurs selectively in the ferrite phase in light chloride solutions.

In this study, the extraction of rare earth elements (REEs) from chloride solutions containing mixtures of these metals with solutions of the mixtures of P507 and Cyanex 272 (1:1) of various concentrations was experimentally studied. It was shown that the distribution coefficients of all REEs decrease with increasing concentration of these metals in the initial solution, which is associated with the loading of the organic phase. The most significant improvement in the extraction is observed for heavy group of rare earth elements. The extractability of REEs enhances with increasing atomic number of the element, as is typical for the extraction of these metals with acidic organophosphorus extractants. The data obtained show that separation factors of adjacent rare earth elements mainly decrease with increasing concentration of metals in the initial aqueous solution. Increasing the concentration of the extractant mixture does not have a significant effect on the values of the adjacent REE separation factors. Analysis of the experimental results shows that two commercial products can be obtained from a concentrate of the medium-heavy group. In the first cascade, yttrium can be separated, in the second, a concentrate of dysprosium and terbium can be obtained.

The research on calcium leaching of 3D printed cement pastes (3DPC) exposed in aggressive water is limited, and the mechanism underlying its effect needs to be better understood. The performance anisotropy of degraded 3DPC due to calcium leaching is investigated in this paper. Samples with aggregate micro fines (AMF) and fly ash (FA) were prepared. A 6 mol/L NH₄Cl solution was used in the accelerated experiment. At specific leaching durations, performances were tested on the samples in different leaching directions. Results show that the performances of 3DPC in aggressive water have a significant anisotropic behavior. The evolution of pore defects and hydration products mainly governs the performance anisotropy of degraded 3DPC. The remaining hydration products of the surface of 3DPC leached in the Z direction are less than the other two directions because calcium ions leached in the Z direction are difficult to be compensated through weak interfaces between layers.

Salinity substantially affects plant growth and crop productivity worldwide. Plants adopt several biochemical mechanisms including regulation of antioxidant biosynthesis to protect themselves against the toxic effects induced by the stress. One-year-old Pistachio rootstock exhibiting different degrees of salinity tolerance were subjected to sodium chloride induced salt stress to identify genetic diversity among cultivated pistachio rootstock for their antioxidant responses, and to determine the correlation of these enzymes to salinity stress. Leaves and roots were harvested following NaCl-induced stress. Results show that a higher concentration of NaCl treatment induced oxidative stress in the leaf tissue and to a lesser extent in the roots. Both tissues showed an increase in ascorbate peroxidase, superoxide dismutase, catalase, glutathione reductase, peroxidase and malondialdehyde. Responses of antioxidant enzymes were cultivar dependent, as well as temporal and dependent on the salinity level. Linear and quadratic regression model analysis revealed significant correlation of enzyme activities to salinity treatment in both tissues. The variation in salinity tolerance reflected their capabilities in orchestrating antioxidant enzymes at the roots and harmonized across the cell membranes of the leaves. The study provides a better understanding of root and leaf coordination in regulating the antioxidant enzymes to NaCl induced oxidative stress.

In this study, a slow-release urea fertilizer hydrogel was synthesized from hydroxyl propyl methyl cellulose, polyvinyl alcohol and glycerol blends with paper (blended paper) as second layer. The fertilizer hydrogel was characterized by SEM, XRD and FTIR. Its retention in sandy soil, swelling behavior in distilled and tap water as well as slow-release behavior to urea were investigated. The results indicated that the fertilizer had good slow-release properties and ability to retain water in soil. However, the addition of blended paper as a second layer matrix was found to help improve the release properties of the fertilizer. The swelling kinetic of the hydrogel followed the Schott’s Second order model. The release kinetics of urea in water was best described by the Zero order model signifying that the release behavior was independent of fertilizer concentration

Scaffolds are widely used in tissue engineering because their manufacture is based on natural and synthetic polymers, which allows them to have properties such as biocompatibility and biodegradability, creating an ideal environment for cell growth on their surface. In this context, among the polymers studied in Tissue Engineering are Chitosan (CH) and Polyvinyl Alcohol (PVA). CH is a versatile polymer obtained from de-acetylation of chitin, which is used for its high biodegradability and biocompatibility, although its mechanical properties must be improved. It has been found that one of the ways to improve the mechanical properties of CH is to mix it with other synthetic polymers such as PVA. PVA is known for its biocompatibility, biodegradability, zero toxicity and ease of preparation due to its solubility in water and excellent mechanical properties, such as tensile strength and ease in the formation of films and barriers. In this study we evaluated the capacity of scaffolds made with CH and PVA in different concentrations (2: 1, 1: 1, 1: 2, respectively) as a possible application in bone regeneration. This was made through different characterization tests such as Infrared Spectroscopy, AFM, Swelling test and Porosity test, where we obtained information about its structural and physicochemical properties. Additionally, a cellular quality control was performed on the material through the MTT assay. The Fourier transform infrared spectroscopy (FTIR) study showed that there are strong intermolecular hydrogen bonds between the chitosan and polyvinyl alcohol molecules. The Swelling and Porosity tests showed favorable results, obtaining maximum values ​​of 5519% and 72.17% respectively. MTT tests determined that the prepared materials are not cytotoxic. These findings suggest that scaffolds possess properties suitable for use in Tissue Engineering.

The service life of the reinforced concrete structure in the marine environment can be impaired significantly due to chloride-induced corrosion. However, how the chloride diffusion in pre-cracked concrete structures is affected by the hydrostatic pressure magnitude is poorly understood. This study experimentally examined the effect of hydrostatic pressure on the chloride diffusion in pre-cracked concrete. Cracks with five different widths, i.e., 20 μm, 40 μm, 60 μm, 80 μm, and 100 μm, were manually created using a splitting tensile apparatus respectively. The chloride diffusion in the concrete with a certain crack was then studied under four different hydrostatic pressures of 0 MPa, 0.1 MPa, 0.3 MPa, and 0.5 MPa. Experimental results show that the chloride diffusion in concrete with a crack greatly relies on both the hydrostatic pressure and the crack width. The chloride concentration increases as the hydrostatic pressure grows, particularly for the wider cracks with width ranging from 60 μm to 100 μm. Surprisingly, the hydrostatic pressure has a negligible effect on the chloride distribution in the concrete with a crack width no larger than 40 μm. Both the chloride diffusion coefficient and the surface chloride concentration of concrete increased gradually as the hydrostatic pressure increased. The experimental findings enrich our understanding of the behavior of pre-cracked concrete when exposed to chloride-induced corrosion at different depths of marine environments.

The paper presents a synthesis of deep eutectic solvents (DESs) based on choline chloride (ChCl) as hydrogen bond acceptor and phenol (Ph), glycol ethylene (EG), and levulinic acid (Lev) as hydrogen bond donors in 1:2 molar ratio. DESs were successfully used as absorption solvents for removal of dimethyl disulfide from (DMDS) from model biogas steam. Several parameters affecting the absorption capacity and absorption rate has been optimized including kind of DES, temperature, the volume of absorbent, model biogas flow rate, and initial concentration of DMDS. Furthermore, reusability and regeneration of DESs by means of adsorption and nitrogen barbotage followed by the mechanism of absorptive desulfurization by means of density functional theory (DFT) as well as FT-IR analysis were investigated. Experimental results indicate that the most promising DES for biogas purification is ChCl:Ph, due to high absorption capacity, relatively long absorption rate, and easy regeneration. The research on the absorption mechanism revealed that van der Waal interaction is the main driving force for DMDS removal from model biogas.

Tomato is considered moderately sensitive to salinity, which detracts from the quality and yield of its fruit; therefore, wild populations have been used as a genetic resource. The aim of this research was to identify lines derived from wild tomato populations with tolerance to salinity during the germination and seedling stages. During germination, 52 wild lines and 2 commercial hybrids (Imperial®, Reserva®) were subjected to 150 mM and 0 mM NaCl and evaluated. The test was carried out for 20 days in a germination chamber with constant darkness, temperature of 25±2 °C and relative humidity of 80±4%. At the seedling stage, 22 wild tomato lines with the best performance in the germination test and 2 commercial hybrids (Imperial®, Topanga®) were evaluated for 12 days in a floating raft system. Concentrations of 175 mM and 0 mM NaCl were used. During germination, the saline condition decreased germination percentage (65.2%), speed of germination (88.2%), steam length (72.5%), root length (46.56%), normal plants number (59.5%), stem dry matter (68.78%), root dry matter (61.99%), and total dry matter (67.1%). At the seedling stage, this condition decreased (P<0.05) the aerial part dry matter (46.37%), leaf area (59.35%), root length (42.43%), final plant height (40.24%), and growth rate (71.42%). Seventeen tolerant genotypes were identified at one of both developmental stages, while one genotype showed tolerance at both stages. These results indicate that there are different response mechanisms in each developmental stage. Native tomatoes play an important role in the identification of tolerant genotypes since they can be used as genetic resources for obtaining commercial genotypes with salt tolerance.

The use of disinfectants, particularly those containing quaternary ammonium compounds (QUACs), has dramatically escalated globally since the coronavirus disease 2019 pandemic. We report a case that highlights the risks associated with the ingestion of a low-concentration QUACs solution and emphasizes the importance of effective management in resolving severe lesions without sequelae. A 17-month-old boy experienced severe respiratory failure after ingesting a disinfectant containing benzalkonium chloride (BAC). The child was initially treated in a local emergency department and was subsequently transferred to a pediatric poison center. Upon evaluation, the child was found to have grade III-A corrosive esophageal lesions and chemical pneumonitis. Several complications, including massive pneumothorax and candidemia, occurred during the clinical course of the disease. However, with timely medical intervention and appropriate supportive care, the patient completely recovered without any long-term sequelae. The properties of BAC and a comprehensive management approach may have been responsible for the patient's full recovery despite the potential life-threatening effects of the ingestion of disinfectants.

The present research intents to study the evolution of the skin fatty acids and physiological disorders through cold storage in ‘Golden Delicious’ apples treated with 1-MCP and calcium. Harvested fruit were treated with calcium chloride (Ca), 1-MCP (MCP), Ca+MCP or no treatment (control) then subjected to cold storage at 0.5 ºC for 6 months. Fatty acids composition, Malondialdehyde (MDA) and the physiological disorders bitter pit (BP), superficial scald and diffuse skin browning (DSB) were measured at harvest and after storage plus 7 days shelf-life at room temperature ≈22 ºC. Palmitic acid decreased and linoleic acid increased through time, while oleic and stearic acids had few changes. Unsaturated/saturated fatty acids and MDA increased through time, despite Ca and Ca+MCP were related to lower MDA and lower BP and rotten fruit, after cold storage and shelf-life. In those treatments, the unsaturated/saturated fatty acids were higher, mainly due to higher linoleic acid and lower palmitic acids. Further research is needed to clarify the changes in membrane properties and the effect of some treatments in response to chilling injury through storage.

A novel prediction model for crack development of reinforced concrete (RC) piles with localized chloride corrosion in marine environment is proposed. A discrete method is used to solve the corrosion pit radius model and a crack extension model is developed to investigate the initiation and extension of cracks. The maximum corrosion degree of reinforced concrete pile is predicted according to the limit crack criterion, and finally a sensitivity analysis is carried out on the important parameters of crack extension. The results show that the radius of corrosion pit, the depth corrosion pit and cross-sectional area loss of reinforcement gradually increase as the corrosion level increases. The loss of local reinforcement section at crack initiation decreases with the increase of the ratio of concrete cover to initial diameter, and increases with the increase of pitting factor. The required pit depth for reinforcement cracking increases with the increase of the ratio of concrete cover thickness to diameter. The loss of cross-sectional area of reinforcement and the radius of corrosion pit increase with the increase of initial diameter of reinforcement. Increasing the pitting factor will reduce the pit depth and make the crack width develop faster before reaching the limit crack width. Increasing the concrete cover thickness can provide an improvement in the propagation of cracks. A comparative analysis shows that the localized corrosion pattern is more in conformity with marine engineering practice.

Molten salt reactors have gained substantial interest in the last years due to their flexibility and their potential for simplified closed fuel cycle operation for massive net-zero energy production. However, a zero-power reactor experiment will be an essential first step into the process of delivering this technology. The topic of the control and shut down for a zero power reactor is for the first time introduced through a literature review and the reduction of the control approaches to a limited number of basic functions with different variations. In the following, the requirements for the control and shutdown system for a reactor experiment are formulated, and based on these assessments, an approach for the shutdown – splitting the lower part of the core with reflector, and an approach for the control – a vertically movable radial reflector are proposed. Both systems will be usable for a zero-power system with a liquid as well as with as a solid core and even more importantly, both systems somehow work on the integral system level without disturbing the central part of the core which will be the essential area for the experimental measurements. Both approaches have been investigated as a singular system as well as their interactions with one another and the sensitivity of the control system. The study has demonstrated that both proposed systems are able to deliver the required characteristics with sufficient shutdown margin and a sufficiently wide control span. The interaction of the system has been shown to be manageable and the sensitivity is on a very good level. The multi-group Monte-Carlo approach has been cross evaluated by a continuous energy test leading to good results, but they also demonstrate that there is room for improvement.

Immersion in salt-lake solution was adopted to periodically test the concrete chloride-ion diffusion coefficient. The regression analysis was also completed. Also investigated was the time-dependent law of concrete chloride-ion diffusion coefficient with time. The influence of chloride-ion concentration in solution, water-to-cement ratio, and corrosion time on the largeness and accumulation rate of the concrete chloride-ion diffusion coefficient was also analyzed. Test results show that the concrete chloride-ion diffusion coefficient gradually decreased with increasing time and increased with increasing chloride-ion concentration in a salt lake . Taking into account the influence of factors such as water–binder ratio, chloride-ion concentration, and time-varying characteristics, a multi-factor calculation model for the concrete chloride-ion diffusion coefficient was established. Combining the prediction results and the measured data reported in this paper, the effectiveness and applicability of the established concrete chloride-ion diffusion coefficient calculation model were compared and verified, and the durability design and service life of a concrete structure under cool chlorine were compared. The results of analysis provide important boundary conditions.

Water quality monitoring was an important objective in the surroundings. In this study, we investigated the sensing characteristics of the arrayed flexible chloride sensor with XBee wireless sensing system. The sensitivity and linearity of the wireless chloride sensing devices were 91.6 mV/pCl and 0.988, respectively. The hysteresis voltages were 50.14 mV and 36.71 mV during the cycles of 1 M → 10⁻¹ M → 1 M → 10⁻³ M → 1 M and 1 M → 10⁻³ M → 1 M → 10⁻¹ M → 1 M, respectively. The selectivity coefficients of the ClO⁻ ion, ClO₄⁻ ion, NO₃⁻ ion and I⁻ ion for Cl⁻ ion were 5.0 × 10⁻², 1.0 × 10⁻¹, 5.9 × 10⁻³ and 5.6×10⁻¹, respectively. The sensing characteristics of real time measurement were investigated for dynamic microfluidic. The arrayed flexible chloride sensor was integrated with the microfluidic device, syringe pump and wireless sensing system. The sensitivity and linearity were 273.1 mV/pCl and 0.978 at 35 μL/min, respectively.

Considering the important demand of fresh water and its scarce availability, water desalination is an interesting technology, producing about 44 Mm³/year worldwide, but, in general the most common desalination techniques are highly energy demanding. Freezing-Melting (F/M) desalination uses just up to 70% less thermal energy, but is the least used process mainly, due to the difficulty of the salt separation. This study proposes a model able to analyses the thermodynamic potential that allows the salt diffusion during the F/M process, using an aqueous solution of sodium chloride. This should allow to obtain a sensitive analysis of the process to promote the separation between the high concentration brine and the ice with liquid separation by physical process. The unidimensional model is based on the evolution of both processes: thermal and mass diffusions, depending on temperature and saline gradients, predicting whether the salt will remain inside the ice or not. Thus, the thermal potential is adjusted to frozen only when the salt has been "pushed" towards the brine. Mostly models have base their results on the assumption of a “certain value of saline concentration of the liquid fraction”, value in which there is great disagreement. In this paper the calculations are based on the concentration in the solid-liquid interface, which has been extensively studied and there is a coincidence in those results, being the main advantage of the proposed model.

An efficient, eco-compatible and very cheap method for the construction of triazoles via eliminative azide–olefin cycloaddition (EAOC) reaction has been developed by a catalytic system IL/FeCl3, offering an highly regioselective approach to structurally diverse 1,5-disubstituted 1,2,3-triazoles in up to 95% yield. This strategy features the reuse of catalytic system through simple operations. Mechanistic studies indicated that an asynchronous concerted dipolar cycloaddition-elimination process might be involved.

For concrete structures exposed to offshore areas, chloride ion erosion is one of the main factors affecting the durability. It is crucial to evaluate chloride ion permeability resistance of concrete structures. In this article, a finite element simulation of the chloride ion diffusion process in concrete is conducted. A mass diffusion finite element model based on random aggregate approach is established to investigate the influence of aggregate, interface transition zone, and micro-cracks on chloride ion diffusion coefficients in concrete. The results show that the mass diffusion finite element analysis based on the exponential function model and power function model can effectively simulate the chloride ion diffusion process in concrete. In addition, the data reveal that coarse aggregate is the most important factor affecting chloride ion diffusivity in concrete. However, the interface transition zone significantly accelerates chloride ion diffusion in concrete. Moreover, this acceleration effect exceeds the barrier effect of aggregate.

Molten salt reactors have gained substantial interest in the last years due to their flexibility and their potential for simplified closed fuel cycle operation for massive net-zero energy production. The importance of a zero-power reactor for the process of developing a new, innovative rector concept like molten salt fast reactor is described here. It is based on historical developments as well as the current demand for experimental results and key factors that are relevant to the success of the next step in the development process of all innovative reactor types. In the systematic modelling & simulation of a zero-power molten salt reactor, the radius and the feedback effects are studied for a eutectic based system, while a heavy metal rich chloride-based system are studied depending on the uranium enrichment accompanied with the effects on neutron flux spectrum and spatial distribution. These results are used to support the relevant decision for the narrowing down of the configurations supported by considerations on cost and proliferation for the follow up 3D analysis to provide for the first time a systematic modelling & simulation approach for a new reactor physics experiment. The expected core volumes for these configurations have been studied using multi-group and continuous energy Monte-Carlo simulations identifying the 35% enriched systems as the most attractive and finally leading to the choice of the heavy metal rich compositions 35% enrichment as the reference system for future studies of the next steps in the zero power reactor investigation. The inter-comparison of the different applied codes and approaches available in the SCALE package has delivered a very good agreement between the results creating trust into the developed and used models and methods.

Clinker production is being reduced worldwide in response to the need to drastically lower greenhouse gas emissions. The trend began in the nineteen seventies with the advent of mineral additions to replace clinker. Blast furnace slag and fly ash, industrial by-products that were being stockpiled in waste heaps at the time, have not commonly been included in cements. Supply of these additions is no longer guaranteed, however, due to restrained activity in the source industries for the same reasons as in clinker production. The search is consequently on for other additions that may lower pollutant gas emissions without altering cement performance. In this research bentonite, a very common clay, was used as such an addition directly, with no need for pre-calcination, an still novel approach that has gone little explored to date for reinforced concrete with structural applications. The results of the mechanical strength and chemical resistance (to sulfates, carbonation and chlorides) tests conducted are promising. The carbonation findings proved to be of particular interest, for that is the area where cement with mineral additions tend to be least effective. In the bentonite-bearing material analysed here, however, carbonation resistance was found to be low as or lower than observed in plain Portland cement.

Molecular and morphological properties of poly(vinyl chloride) grains produced by suspension polymerization of VCM in the presence of a mixture of three kind of initiators (i.e. fast, mild and slow) (named as Cok process) was experimentally investigated in a pilot-scale reactor. The results obtained here were initially compared with a isothermal regular process (named as control process) and then with those obtained already for other productivity-enhancing polymerization techniques (i.e. nonisothermal and fast initiator dosage process). The results showed that, in contrast to nonisothermal and fast initiator dosage process, the addition of initators mixture at the beginning of the reaction has the smallest influence on molecular weight and polydispersity index compared to control process. It is obvioused that Cok-PVC grains have the lowest cold plasticizer absorption and porosity among these mentioned processes. Scanning electron microscopy (SEM) showed that the particles produced by Cok process are more regularly shaped, with a smoother surface compared with the control product. According to the literatures, all three productivity-enhancing techniques lead to an apparent quality enhancement, higher flowability and greater bulk density of final grains. While both processes of continous initiator dosage and nonisothermal polymerization broaden the particle size distribution of final PVC grains, applying initiator mixture produces particles with the same particle size distribution as control process. The SEM images processing showed that Cok process deccelerates the formation of a three-dimensional skeleton of primary particles relative to the control polymerization. In comparison with nonisothermal trajectory and continous fast initiator dosage system, the Cok polymerization process leads to the most delay of motionless conversions and fusion time as well.

Hazardous chemicals like toxic organic dyes are very harmful to the environment and their removal is quite challenging. Therefore there is a necessity to develop techniques, which are environment friendly, cost-effective and easily available in nature for water purification and re-mediation. The present research work is focused on the development` and characterization of the ecofriendly polyvinyl alcohol (PVA) and alginate (Alg) hydrogel beads incorporating natural bentonite (Bent) clay as beneficial adsorbents for removal of toxic methylene blue (MB) from industrial water. PVA−Alg/Bent nanocomposite hydrogel beads with different Bent content (0, 10, 20, and 30 wt%) were synthesized via external ionic gelation method. The designed porous and steady structure beads were characterized by the use of Fourier transform infrared spectroscopy (FTIR), energy-dispersive X-ray spectroscopy (EDX), and scanning electron microscopy (SEM). The performance of the beads as MB adsorbents was investigated by treating batch aqueous solutions. The experimental results indicated that the incorporation of Bent (30 w%) in the nanocomposite formulation sustained porous structure, preserved water uptake, and increased MB removal effi-ciency by 230 % compared to empty beads. Designed beads possessed higher affinity to MB at high pH 8, 30 °C, and fitted well to pseudo-second-order kinetic model a high correlation coefficient. Moreover, designed beads had a good stability and reusability as they exhibited excellent removal efficiency (90%) after six consecutive adsorption-desorption cycles. Adsorption process was found be combination of both monolayer adsorption on homogeneous surface and multilayer adsorption on heterogeneous surface. The maximum adsorption capacity of the designed beads system as calculated by Langmuir isotherm was found to be 51.34 mg/g, which is in good agreement with the reported clay-related adsorbents. The designed PVA−Alg/Bent nanocomposite hydrogel beads demonstrated good adsorbent properties and could be potentially used for MB removal from polluted water.

One of the influential factors in estimating the service life of reinforced concrete bridges (RCB) is determining the long-term seismic performance of these structures. Corrosion due to chloride ion diffusion leads to the destruction of critical members of the RCB during the useful life of the structure. So, the long-term seismic performance of the bridge deteriorates as a result. It is essential to study the effect of corrosion deterioration on the long-term seismic performance of bridges in the southern regions of Iran, near the coasts of the Persian Gulf and the Oman Sea, because of the seismicity of the region and high corrosion rate of reinforced concrete (RC) members is the result of environmental conditions. In order to investigate this issue, considering studies about environmental conditions of southern Iran, the onset time of corrosion in the columns, as seismic critical members of the bridge, was determined. Based on that, the corrosion's effect on characteristics of RC at specific time points during the bridge's useful life (0, 15, 30, 45, 60, 75 and 90 years) have been calculated. The effects of corrosion include deterioration of the core and cover concrete properties, steel bar and the connection between concrete and steel bar. In the next step, at each time point, according to the modified stress-strain relationships, the moment-curvature analysis of the bridge pier was done, and the properties of the plastic hinge were determined. Finally, based on the obtained data about plastic hinge characteristics at each time point, overload analysis of the bridge was performed in both longitudinal and transverse directions. Then the capacity curves of RCB were compared at the mentioned time-points. The results show that the capacity of the bridge deteriorates over time due to corrosion. Therefore, a proposal to increase the value of base shear design has been made to ensure the long-term seismic performance of RCB in corrosive environments.

In this research, a novel collector cetyl trimethyl ammonium chloride (CTAC) was used to separate hematite from quartz via reverse flotation for the first time. Micro-flotation tests showed that CTAC had a strong ability to selectively collect quartz and a separation of hematite from quartz could be accomplished with a concentration of 0.00263 mmol/L CTAC. Zeta-potential measurements indicated that the positive CTAC+ species could selectively increase the surface potential of quartz, but it had rather a weak effect on the hematite surface. X-ray photoelectron spectroscopy (XPS) detection indicated that CTAC had a stronger binding affinity to oxygen sites on the surface of quartz than that of hematite, resulting in a large amount of CTAC predominantly adsorbed on quartz rather than hematite.

We discuss the electrodeposition of two-dimensional (2D) Pt-nanostructures on HOPG achieved under constant applied potential versus a Pt counter electrode (Eappl = ca. - 2.2 V vs RHE). The deposition conditions are discussed in terms of the electrochemical behavior of the electrodeposition precursor (H2PtCl6). We performed cyclic voltammetry (CV) of the electrochemical Pt deposit on HOPG and on Pt substrates to study the relevant phenomena that affect the morphology of Pt deposition. Under conditions where the Pt deposition occurs and H2 evolution is occurring at the diffusion-limited rate (- 0.3 V vs RHE), Pt forms larger structures on the surface of HOPG, and the electrodeposition of Pt is not limited by diffusion. This indicates the need for large overpotentials to direct the 2D growth of Pt. Investigation of the possible effect of Cl- showed that Cl- deposits on the surface of Pt at low overpotentials, but strips from the surface at potentials more positive than the electrodeposition potential. The CV of Pt on HOPG is a strong function of the nature of the surface. We propose that during immersion of HOPG in the electrodeposition solution (3 mM H2PtCl6, 0.5 M NaCl, pH 2.3) Pt islands are formed spontaneously, and these islands drive the growth of the 2D nanostructures.

In cold-climate regions, road salt is used as a de-icer for winter road maintenance. The applied road salt melts ice and snow on roads, being washed off through storm sewer systems into nearby urban streams, harming the freshwater ecosystem. Addressing the gap in the knowledge regarding the use of deep learning approaches for urban stream water quality forecasting, the present work discusses our implementation of a “Graph Neural Network” - “Sample and Aggregate” (GNN-SAGE) model for forecasting chloride concentrations in the Credit River in Ontario, Canada. The proposed GNN-SAGE is compared to other models, including a Deep Neural Network based transformer (DNN-Transformer) and a benchmarking persistence model for 6 hours forecasting horizon. Ac-cording to the results, the GNN-SAGE model surpasses other models in providing accurate predic-tions of chloride concentrations within the assessed prediction window. Also, a SHAP analysis provides insight into the variables that influence the model’s forecasting, showing the impact of the spatiotemporal neighbouring data from the network and the seasonality variables on the model’s result. The GNN-SAGE model shows potential for use in real-time forecasting of water quality in urban streams, aiding in the development of regulatory policies to protect the vulnerable freshwater ecosystems in urban areas.

Deep eutectic solvents (DESs) have emerged as novel alternatives to common solvents and VOCs. Their employment as electrolytes in battery has been an area of intense research. In this context, understanding changes in physicochemical properties of DESs in the presence of Li salts becomes of utmost importance. Solvatochromic probes have potential to gauze such changes. It is reported herein that one such uv-vis molecular absorbance probe, Reichardt’s betaine dye 33, effectively manifests changes taking place in a DES Glyceline, composed of H-bond accepting salt choline chloride and H-bond donor glycerol in 1 : 2 molar ratio, as salt LiCl is added. Lowest energy intramolecular charge-transfer absorbance band of this dye exhibits 17 nm hypsochromic shift as up to 3.0 molal LiCl is added to Glyceline. The estimated ETN parameter shows linear increase with LiCl mole fraction. Spectroscopic responses of betaine dye 33, N,N-diethyl-4-nitroaniline and 4-nitroaniline are used to assess empirical Kamlet-Taft parameters of dipolarity/polarizability (π*), H-bond donating acidity (α) and H-bond accepting basicity (β) as a function of LiCl concentration in Glyceline. LiCl addition to Glyceline results in increase in α and no change in π*and β. It is proposed that added lithium interacts with oxygen of the –OH functionalities on the glycerol rendering the solvent with increased H-bond donating acidity. It is observed that pyrene, a popular fluorescence probe of solvent polarity, does respond to the addition of LiCl to Glyceline, however, the change in pyrene response starts to become noticeable only at higher LiCl concentration (mLiCl ≥ 1.5 m). Reichardt’s betaine dye is found to be highly sensitive and versatile in gauzing physicochemical properties of DESs in the presence of LiCl.

Background. Traumatic brain injury (TBI) is the main cause of disabilities over the industrialized countries. Cognitive decline appears in the chronic phase of the pathology consecutively to cellular and molecular processes. Here we described the use of KCC2, a neuronal-specific potassium-chloride transporters as potent biomarker to predict cognitive dysfunctions after TBI. Methods. Using neuronal and total exosomes collection from blood serum in control and TBI subjects we were able to anticipate the decline of cognitive performance. Results. After TBI, we observed a significative and persistant loss of KCC2 expression in the blood exosomes that is correlated to changes in network activity and cellular processes such as secondary neurogenesis. Also we correlated this KCC2 loss in expression to the appearance of the cognitive decline observed in mice and more particularly we correlate the KCC2 loss of expression to the appearance of the depressive-like behavior. Conclusion. According to our protocol, we were able to confirm our previous findings in agreement with the potential therapeutic effect of bumetanide in the prevention of the post traumatic depression after TBI, by restoring the KCC2 expression thus preventing the massive neuronal death of interneurons and the secondary neurogenesis effect observed in such model.

In this study, the effect of extraction conditions on the total phenolic content of clove buds was investigated. Clove buds were extracted using a deep eutectic solvents like mixtures choline chloride: lactic acid in the 1:2 molar ratio. Additionally, the HPLC-DAD method was used to determine the main components of the clove extracts, including eugenol, eugenol acetate, and β-caryophyllene. The conditions used in the extraction with choline chloride: lactic acid (molar ratio 1:2) included extraction temperature (t = 40 – 80°C), water addition (5.6 – 40%), and extraction time (30 – 90 min). Determination of the phenolic compounds was done by the Folin-Ciocalteu method. The optimum operating conditions for the total phenolic content were identified at 77°C, 30 min, and a water addition of 40%. Based on the results, the highest amount of eugenol (307.26 ± 8,44 mg/g dry raw material) was determined in clove extracts which were extracted under condition of 60°C, 22.8%, and 30 min.

The interfacial polymerization (IP) of piperazine (PIP) and trimesoyl chloride (TMC) has been extensively utilized to synthesize nanofiltration (NF) membranes. However, it is still a huge challenge to monitor the IP reaction, because of the fast reaction rate and the formed ultra-thin film. Herein, two effective strategies were applied to reduce the IP reaction rate: (1) the introduction of hydrophilic interlayers between the porous substrate and the formed polyamide layer, and (2) the addition of macromolecular additives in the aqueous solution of PIP. As a result, in situ Fourier transform infrared (FT-IR) spectroscopy was firstly used to monitor the IP reaction of PIP/TMC with hydrophilic interlayers or macromolecular additives in the aqueous solution of PIP. Moreover, the formed polyamide layer growth on the substrate was studied in a real-time manner. The in situ FTIR experimental results confirmed that the IP reaction rates were effectively suppressed and that the formed polyamide thickness was reduced from 138 ± 24 nm to 46 ± 2 nm according to TEM observation. Furthermore, an optimized NF membrane with excellent performance was consequently obtained, which included boosted water permeation of about 141–238 (L/m²·h·MPa) and superior salt rejection of Na₂SO₄ > 98.4%.

The seeds of red clover are heteromorphic and two color morphs can be visually recognized, light purple and yellow, resulting from heterozygosity and recessive homozygosity at two loci. Here, we report the responses of seed imbibition, seed germination, and early seedling growth of the two morphs to distilled water, sodium chloride, and complete nutrient solution. The sensitivity of red clover seeds to treatments increased with the stage of development in what seems to be a cumulative process. No differences were found in seed imbibition between morphs or between treatments. In seedling growth, on the contrary, treatments were always effective, but differences between morphs were only observed in seeds that were treated with nutrient solution, whereas in the intermediate stage of seed germination, the effects by treatments were observed together with the appearance of differences between morphs in distilled water and in the treatment by sodium chloride solution. Simultaneously, the superior performance of the yellow morph that was found in germination, which appears to be a trait stable across cultivars of red clover seeds, turned into a superior performance of the light purple morph in seedling growth.

Synthesis and antitumour activity of a palladium compound, [Bis (quinoline) palladium (II) chloride] (coded as NH1) alone and in combination along with its proposed mechanism of action has been described in the present study. Antitumour activity has been performed in seven different cancer cell lines using colorimetric 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl-2H-tetrazolium bromide (MTT) assay. The investigated palladium compound demonstrated superiority over clinical standard cisplatin against drug resistant ovarian cancer cell lines. NH1 also demonstrates 4.4 times greater activity than cisplatin against breast cancer model. Binary sequenced combination study showed that NH1 in combination with curcumin is mostly additive to antagonistic. However, combination of NH1 with 6-shogaol demonstrated synergism depending on dose and sequence. Proteomic study revealed that changes in expression of 14 proteins were significantly associated with anticancer mechanism of NH1. In vivo anticancer activity of NH1 at a dose of 0.75 mg/kg was also evaluated using Erlich Ascites Carcinoma (EAC) cell lines in Swiss-albino mice model. Preliminary toxicity study in Swiss-albino mice proved that NH1 is comparatively less toxic at both of the administered doses, either 2.5 mg/kg or 5 mg/kg. However, cisplatin demonstrated significant toxicity at both of the administered doses. Biochemical investigations also supported that NH1 demonstrated lesser toxicity profile towards liver or kidney compared to clinical standard cisplatin.

The anodic polarization response of magnesium alloy AZ31 was characterized during exposure to aerated 0.1M NaCl solutions with millimolar additions of NaVO₃, Na₃PO₄, Na₂HPO₄, NaF and various pairings to assess their ability to inhibit corrosion kinetics and retard localized corrosion. Each of the candidate inhibitors reduced the corrosion rate of the alloy to some degree. A Na₃PO₄ - NaVO₃ pair produced a powerful inhibiting response decreasing the corrosion rate to about 10^-7 A/cm², which was two orders of magnitude lower than the uninhibited control case. A Bliss Independence assessment indicated that this inhibitor pair acted synergistically. A Na₂HPO₄ - NaVO₃ pair reduced the corrosion rate to 10^-6 A/cm² but was not assessed to be acting synergistically. The NaVO₃ - NaF pair did not reduce the corrosion rate significantly compared to the control case and was an antagonistic pairing. SEM imaging showed film formation due to exposure, which appears to be the origins of the observed inhibition. The resistance to localized corrosion was assessed as the difference in the breakdown potential and the corrosion potential with larger values indicating a lower probability of localized corrosion during free corrosion exposures. Effects of the inhibitors on this characteristic were mixed, but each of the inhibitor pairs yielded potential differences in excess of 100mV. A conceptual conversion coating process based on a mixture of vanadate and phosphate compounds were demonstrated. A fluoride-bearing formulation produced coatings whose total impedance was increased by a factor or 2 compared to an uncoated control. A fluoride-free formulation produced coatings whose corrosion resistance was increased by more than a factor of 3.

Nitriding has long been used to engineer the surfaces of engineering steels to improve their surface and subsurface properties. The role of the surface compound layer (’-Fe4N and/or -Fe2-3N) in improving the tribological and corrosion resistant properties of nitrided steels has been established. However, there have been very few studies on the response of the compound layer to tribocorrosion in corrosive environments. In this work, the tribocorrosion behaviour of a 5 m thick ’-Fe4N nitride layer produced on mild steel (MS) by plasma nitriding has been studied in a NaCl containing solution under various electrochemical conditions. The results show that at a cathodic potential, where mechanical wear is predominant, the total material removal (TMR) from the ’-Fe4N layer is 37% smaller than that from the untreated MS, and at open circuit potential, TMR from the layer is 35% smaller than that from the untreated MS, while at an anodic potential, the ’-Fe4N layer can reduce TMR from mild steel by 87%. The beneficial effect of the ’-Fe4N nitride layer in improving the tribocorrosion behaviour of mild steel is derived from its high hardness and good corrosion resistance in the test solution and its ability to resist both mechanical wear and chemical wear.

Molten salt reactors have gained substantial interest in the last years due to their flexibility and their potential for simplified closed fuel cycle operation for massive net-zero energy production. However, a zero-power reactor experiment will be an essential first step into the process delivering this technology. The choice of the optimal reflector material is one of the key issues for such experiments since on the one hand it offers huge cost saving potential due to reduced fuel demand, on the other hand an improper choice of the reflector material can have negative effects on the quality of the experiments. The choice of the reflector material is for the first time introduced through a literature review and a discussion of potential roles of the reflector. The 2D study of different potential reflector materials has delivered a first down selection with SS 304 as representative for stainless steel, lead, copper, graphite, and beryllium oxide. A deeper look identified in addition iron-based material with high Si content. The following evaluation of the power distribution has shown the strong influence of the moderating reflectors creating a massively disturbed power distribution with a peak at the core boundary. This effect has been confirmed through a deeper analysis of the 2D multi-group flux distribution which lead to the exclusion of the BeO and the graphite reflector. The most promising materials identified have been SS 304, lead, and copper. The final 3D Monte-Carlo study demonstrated that all three materials have the potential to reduce the required amount of fuel by up to 60% compared NaCl which has been used in previous studies and is now taken as reference A first cost analysis has identified the SS 304 reflector as the most attractive solution. The results of the 2D multi group deterministic study and the 3D multi group Monte-Carlo study have been confirmed through a continuous energy Monte-Carlo reference calculation showing only minor differences.

Nasopharyngeal carcinoma (NPC) has not been thoroughly studied, and the pathogenesis of NPC is unclear. Scientists have neither discovered effective therapies nor achieved a desirable prognosis. Some studies have found that the regulation of intra- and extracellular ion channels hinges directly on cell apoptosis, and treatment with Gambogenic acid (GNA) brings changes to the volume-sensitive outwardly rectifying chloride (VSOR Cl-) current of CNE-2Z cells recorded by the patch clamp method. Nevertheless, rarely have any researchers probed into the relevance between this variation and the anti-tumor mechanism of GNA. This paper is suggested that GNA activates the VSOR Cl- current on the CNE-2Z cell membrane, and the activation of VSOR Cl- currents by GNA in CNE-2Z cells is blocked by the chloride channel blockers DIDS and DCPIB. GNA induces the down-regulation of GRP78 and up-regulation of ATF4 as well as chop proteins, which is evidence for the induction of CNE-2Z cell apoptosis, and this correlates with ER stress. GNA can activate the VSOR Cl- channel and lead to the occurrence of ER stress, thus inducing the apoptosis of CNE-2Z cells and inhibiting the proliferation of CNE-2Z cells.

Ionic liquids (ILs) have gained interest among researchers due to its tunable properties that can be used in wide applications. However, toxicity and bio-degradation studies of ILs proved that most of the aromatic ILs, such as imidazolium is highly toxic and non-biodegradable. Several advance oxidation processes (AOPs) have been investigated by researchers to evaluate the efficiency of the systems for the removal of ILs from wastewater. However, the issue on relative high cost and environmental concern has limited the application of these AOPs in industry. In this research, photocatalytic study using hybrid nano-materials was conducted to evaluate the efficiency of this system as an alternative AOP system for removal of ILs from wastewater. The synergistic effect of adsorption-photodegradation was introduced by depositing Fe-TiO₂ onto the functionalized activated carbon (AC). Nano-TiO₂ was synthesized using micromulsion method before modification with transition metal and deposited onto the oxidized AC. Photodegradation reaction of 1-butyl-3-methylimidazolium chloride [bmim]Cl was investigated under simulated visible light irradiation. It was observed that the overall efficiency of the system was increased with the increasing amount of Fe dopant. Investigation on the extrinsic factors such as solution pH, initial concentration of ILs and photocatalyst dosage showed to significantly affect the overall efficiency of the systems where the optimum condition for the system was observed at pH 10, with initial ILs at 1mM at 1 g/L of photocatalyst. The best performance photocatalyst was 0.2Fe-TiO₂/AC.

The steady-state dissolution rates of basaltic glass and labradorite have been measured in the presence of 10 to 700 x 10-3 mol kgw-1 aqueous NaCl, KCl, CaCl2, and MgCl2 at 25 oC. All rates were measured in mixed flow reactors, and at pH~3.6 by the addition of HCl to the reactive fluids. Steady-state basaltic glass dissolution rates based on Si release increased by ~0.3 log units in the presence of 1 x 10-2 mol kgw-1 of CaCl2 or MgCl2, compared to their rates in 10 x 10-3 mol kgw-1 of NaCl, and KCl. In contrast, the steady-state dissolution rates of labradorite decreased by ~0.4 log units in the presence of 10 x 10-3mol kgw-1 of CaCl2 or MgCl2, compared to their rates in 10 x 10-3 mol kgw-1 of NaCl, and KCl. These contrasting behaviours likely reflect the varying effects of these cations on the stability of rate controlling Si-rich activated complexes on the surface of the solids. On average, the Si release rates of these solids are similar to each other and increase slightly with increasing ionic strength. As the pH of water charged with 10 to 30 bars CO2 is ~3.6, the results of this study indicate that both basaltic glass and labradorite dissolution will likely be effective at increasing pH and adding Ca to the aqueous phase in saline fluids. This observation supports potential efforts to store carbon through its mineralization in saline aquifers containing Ca-bearing feldspar and in submarine basalts.

The dessert banana is a popular fruit worldwide, but its ripening process is greatly accelerated by high temperatures, which eventually leads to an unpleasant taste and the appearance of spots on the skin of the fruit. To slow down the ripening of bananas, expensive strategies are used, which are usually not practical for conventional farmers in less developed countries. In this study, we try to find a less costly alternative. Therefore, the effects of coatings of lemon peel extract (2.5 %, 5 %, and 10 %), calcium chloride (4 %), and glycerol (2 %) on the shelf life and postharvest quality of banana fruit (Cavendish) stored at 20 ± 3 °C and 50 – 70 % relative humidity were investigated. Treatment with a mixture of 2.5 % lemon peel extract and 2 % glycerol resulted in an extension of the shelf life of the dessert banana by up to 6 days and no detectable fungal infestation. The mixture is an effective alternative to extend the shelf life and reduce quality losses in bananas.

The thermal stabilizers, lubricant, and plasticizers are three crucial additives for processing poly (vinyl chloride) (PVC). In this study, a new mannitol stearate ester-based aluminum alkoxides (MSE-Al) was designed and synthesized as a novel additive for PVC. The thermal stability and processing performance of PVC stabilized by MSE-Al were evaluated by Congo red test, conductivity measurement, thermal aging test, ultravioletevisible (UV-vis) spectroscopy test, and torque rheometer test. Results showed that the addition of MSE-Al can not only markedly improve the long-term thermal stability of PVC, but also greatly accelerate the plasticizing and decrease the balance torque which demonstrated that MSE-Al possesses the lubricating property. Thus, MSE-Al was demonstrated to be able to provide tri-functional additive roles, e.g., thermal stabilizer, plasticizer, and lubricant. The test results for the thermal stability of PVC indicated that the initial whiteness of PVC stabilized with MSE-Al was not good enough, thus the synergistic effect of MSE-Al with zinc stearates (ZnSt₂) on the thermal stability of PVC was also investigated. The results showed that there exhibited an appreciable synergistic effect between MSE-Al and ZnSt₂. The thermal stabilization mechanism and synergism effect of MSE-Al with ZnSt₂ were then discussed.

Regulation (EU) No 305/2011 lays down harmonized conditions for marketing construction products in the European Union. One of its consequences has been the introduction of the product standard EN 50575 and standard EN 130501-6, concerning power, control, and communication cables permanently installed in buildings to prevent the risk of a fire and its consequences. EN 13501-6 provides the reaction to fire classifications for cables, the test methods to be performed, the requirements to meet a specific reaction to fire, and additional classifications for smoke production, flaming droplets, and acidity. EN 60754-2 is the technical standard used to assess acidity, and it defines three classes: a1, a2, and a3 (the less performant), based on pH and conductivity measurements. Due to the release of hydrogen chloride during the combustion, acidity is the weak point of PVC cables, which are not yet capable of achieving the a1 or a2 classes required in specific locations according to a fire risk assessment. EN 13501-6 does not include EN 60754-1. Both EN 60754-1 and EN 60754-2 are common standards for determining halogen gas content, acidity, and conductivity, respectively. They involve the same type of tube furnace but with different heating regimes, final temperatures, and detection methods. EN 60754-2 must be performed at temperatures between 935 – 965 °C. The paper demonstrates that, when EN 60754-2 is carried out with the thermal profile of EN 60754-1 or at 500 °C in isothermal conditions, the evolution of hydrogen chloride changes significantly if potent acid scavengers are utilized in the PVC compounds. The reason lies behind the kinetic of hydrogen chloride release during the combustion of PVC compounds: the higher the temperature or faster the heat release, the quicker hydrogen chloride evolution and the lower the probability for the acid scavenger to trap it. That further highlights the "fragility" of EN 60754-2 as a tool for assessing the risks associated with the release of hydrogen chloride in case of fire

The combustion of PVC cables in fires results in the release of hydrogen chloride gas. In the European Union, Regulation (EU) No 305/2011, in force since 2017, requires the classification of cables permanently installed in buildings for reaction to fire, smoke, flaming droplets, and acidity. The additional classification for acidity is evaluated through EN 60754-2, involving pH and conductivity measurements. This study focuses on the essential research and development of low-smoke acidity PVC compounds for cables, mainly aiming to meet the stringent additional classifications for acidity, a1 or a2, which cannot be achieved with traditional PVC cables. Understanding the chemistry of thermal decomposition and combustion, especially in the presence of hydrogen chloride scavengers, is crucial for meeting the best acidity classification. The article reviews the current tube furnace tests used in the European Union for cable halogen and acidity assessments. It discusses the limitations of the existing method (EN 60754-2) and highlights the potential of emerging tests such as IEC EN 60754-3, which employs ion chromatography for improved sensitivity and specificity. In the experimental part of the article, various standard and low-smoke acidity cable compounds are tested using tube furnace experiments with different heating regimes. The concentrations of cations and anions in solution are measured through ion chromatography and inductively coupled plasma–optical emission spectrometry. This detailed analysis aims to identify the species influencing pH and conductivity, which is crucial for designing effective acid scavengers that do not impact conductivity. The conclusive results emphasize that HCl from PVC thermal decomposition is the primary driver of pH and conductivity, and the contribution from the decomposition of additives and byproducts from combustion is found to be negligible in most of the tested PVC compounds for cables. The findings underscore the importance of understanding the thermal decomposition of PVC compounds to design acid scavengers capable of trapping hydrogen chloride without adversely impacting conductivity.

Redox-flow batteries are rechargeable batteries that store energy in two liquid electrolytes, separated by a membrane. During charging and discharging, the electrolytes flow through the membrane and undergo chemical reactions that generate or consume electrical energy. These batteries are known for their scalability and long cycle life and are versatile energy storage technologies developed to enhance efficiency and lower costs. Deep Eutectic Solvents (DES) are eco-friendly alternatives to traditional electrolytes, and their properties have been studied to improve the performance of redox-flow batteries. We investigated choline chloride/ethylene glycol (ChlCl/Eg) mixtures with LiPF6 salt at four concentrations through experimental and MD simulations. The thermophysical and transport properties of the mixture, including density, diffusion coefficient, viscosity, and ionic conductivity, were calculated across a temperature range of 298.15–398.5 K. Our findings indicate that an increase in salt concentration leads to a decrease in diffusion coefficients and ionic conductivity, while increasing the viscosity of the deep eutectic solvent. This research provides valuable insights into the behavior of DES mixtures and can aid in the design and optimization of DES-based processes for use in redox-flow batteries.

In the European Union, according to the second basic requirement for construction works of Regulation (EU) n. 305/2011, cables permanently installed in residential and public buildings must be classified in terms of reaction to fire, smoke production, flaming droplets, and acidity. The classification is harmonized; nevertheless, every European Union country decides what kind of classification a cable must have to be installed in a specific location, depending on its fire risk, following the assumption that the higher the fire risk of the area, the higher the fire performance of the cable. According to Regulation (EU) n. 305/2011, the acidity is indirectly assessed by performing EN 60754-2, giving an additional class based on pH and conductivity measurements. Hydrogen chloride (HCl) is one of the gases PVC cables release when they burn. In some applications out of the scope of the Regulation, acid scavengers are commonly used in special-grade PVC compounds to reduce the emission of acidic smoke. In this first part of the paper, the European rules on smoke acidity are presented, a review of the literature on HCl scavenging is performed, and an introduction on HCl scavenging at high temperatures is outlined. The paper shows how different experimental conditions and geometries of the test apparatuses used for assessing the smoke acidity can affect the emission of HCl in the gas phase and what critical issues affect the efficiency of acid scavengers at high temperatures in trapping HCl.

In PVC compounds, hydrogen chloride plays a fundamental role in .H and .OH radical trapping lowering the flame energy during combustion. Furthermore, it yields actual Lewis acids promoting the cross-linking of the polyene sequences from PVC degradation and bringing a char layer, protecting PVC items from flames. Therefore, PVC is inherently flame retarded. However, plasticized PVC requires flame retardants and smoke suppressants to enhance fire performance. Low smoke acidity PVC compounds contain potent acid scavengers capable of acting at high temperatures. They react with hydrogen chloride in the condensed phase, making it unavailable in the gas and even in the condensed phase, compromising the reaction to fire and enhancing the smoke produced during the combustion. The effect of the sequestration of hydrogen chloride in PVC compounds for cables by potent acid scavengers has been studied in this paper through measurements of oxygen index, heat release, and smoke production. It is shown that potent acid scavengers strongly affect parameters like fire growth rate in cone calorimetry, specific (total) heat capacity, and specific heat of combustion of fuel gases in micro combustion calorimetry. They neutralize the action of antimony trioxide and Lewis acid precursors commonly used as flame retardants and smoke suppressants in PVC items, making them prone to ignite, release smoke, and spread flame. A new generation of flame retardants and smoke suppressants is necessary to keep low smoke acidity and high fire performances together in PVC items

Milk serves as a crucial source of natural bioactive compounds essential for human nutrition and health. The gastrointestinal digestion of milk proteins releases various biologically active peptides that positively impact human health and enhance physiological performance. With the growing production of cheese, Greek yogurt, and other dairy products, the volume of unutilized acid whey is significantly increasing. Acid whey, containing almost all whey proteins and approximately one-quarter of casein, presents a valuable raw material for generating peptides with potential health benefits. These peptides exhibit properties such as antioxidant, antimicrobial, anti-inflammatory, anticarcinogenic, antihypertensive, antithrombotic, opioid, mineral-binding, and growth-stimulating activities, contributing to improved human immunity and the treatment of chronic diseases. Enzymatic hydrolysis of milk proteins has been developed as a method to produce these peptides, facilitating their use in food fortification. To incorporate whey into functional beverages, it undergoes fermentation by lactic acid bacteria with proteolytic activity. To specifically enrich these beverages with peptides exhibiting targeted bioactivities, it is essential to select lactic acid bacteria strains possessing the requisite protease profiles. Additionally, the sensory properties of the final product can be enhanced using starter cultures with diverse metabolic capabilities, even in the absence of added flavoring agents. Given the imperative to develop waste-free technologies and enhance the profitability of the dairy industry, there is a growing need to efficiently utilize and transform acid whey into a broad spectrum of valuable products and food additives. This approach is justified not only by the nutritional benefits of the bioactive components in whey but also by the commercial potential of safe and health-enhancing products.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.

The Simultaneous Localization And Mapping (SLAM) scanner is an easy and portable Light Detection And Ranging (LiDAR) data acquisition device. Its main output is a 3D point cloud covering the scanned scene. Regarding the importance of accuracy in the survey domain, this paper aims to assess the accuracy of two SLAM scanners: the NavVis VLX and the BLK2GO Scanner. This assessment is conducted for both outdoor and indoor environments. In this context, two types of reference data are used: the Total Station (TS) and the static scanner Z+F Imager 5016. To carry out the assessment, four comparisons are tested: cloud to cloud, cloud to mesh, mesh to mesh, and edge detection board assessment. However, the results of the assessments confirm that the accuracy of indoor SLAM scanner measurements (5 mm) is greater than that of outdoor ones (between 10 mm and 60 mm). Moreover, the comparison of cloud to cloud provides the best accuracy regarding direct accuracy measurement without manipulations. Finally, based on the high accuracy, scanning speed, flexibility, and the accuracy differences between tested cases, it is confirmed that SLAM scanners are effective tools for data acquisition.

The impact of interaction SS with MJO on rainfall along Java Island to East Nusa Tenggara has been studied using daily rainfall observation data from 2140 weather observation stations, which are also equipped with GSMaP, OLR, and ERA5 data. There were 61 SS events found, 17 during active MJO and 44 in inactive MJO. Rainfall increases more in the western study area when the active MJO and more in the eastern study area when the inactive MJO is due to SS. SS reduces rainfall in the Jakarta region, regardless of the activity or inactivity of the MJO. SS causes extreme rainfall to only occur in a small part of certain areas, so it tends to significantly reduce the possibility of extreme rainfall. In the southern part of the IMC, SS predominates over MJO in supporting increased water vapor transport. Large-scale synoptic circulations like the monsoon, SS, and MJO can interact with local land-sea wind circulation to produce spatiotemporal variability in rainfall on Java Island. Rainfall mostly increases in the afternoon and decreases in the morning when SS occurs, whether there is MJO or not. Convective instability analysis indicates that SS increases precipitation, most likely by lowering CIN and raising VIMFC.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

Currently there are fewer depth models applied to pepper picking detection, while the existing generalized neural networks have problems such as large model parameters, long training time, and low model accuracy.In order to solve the above problems, this paper proposes a Yolo-chili target detection algorithm for chili pepper detection. First, the classical target detection algorithm yolov5 is used as a benchmark model, and an adaptive spatial feature pyramid structure combining the attention mechanism and the idea of multi-scale prediction is introduced to improve the model's detection effect on occluded peppers and small target peppers. Secondly, a three-channel attention mechanism module is introduced to improve the algorithm's long-distance recognition ability and reduce the interference of redundant testers. Finally, the quantized pruning method is used to reduce the model parameters and realize the lightweight processing of the model. Applying the method to the homemade chili pepper dataset, the AP value of chili pepper reaches 93.11%; the accuracy rate is 93.51% and the recall rate is 92.55%.The experimental results show that yolo-chili is able to achieve accurate and real-time pepper detection under complex orchards.

The temporary immersion system bioreactor named GreenTray®[2], [3]presents advantages over the existing ones. Firstly, there is no need to use forceps to move the shoots or plantlets in or out of the recipient, neither the use of scalpel to divide them. Secondly, the basis of the shoot can remain in the GreenTray® and can sprout again in several cycles of growth. These two characteristics reduce the costs in the process of micropropagation. Besides, shoots or plantlets development is enhanced by the aeration of the recipient, thus enriching with CO2 the recipient atmosphere. The chapter describes and provides images and values of interest in (1) the micropropagation process of some commercial Prunus or Pyrus rootstocks; (2) the plantlet growth under autotrophic conditions; and (2) the inoculation of plants with pathogens that reproduce in vitro the symptoms observed in vivo, using the GreenTray® bioreactor.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

In this paper we study a class of impulsive delayed neural networks with parameter uncertainties and reaction-diffusion terms. Using the properties of M-matrices and some inequality techniques, some sufficient conditions are derived to guarantee the global exponential stability of the given system. The results obtained are presented by simple algebraic inequalities, which are certainly more concise than previous methods. Finally, the validity and usefulness of our results are illustrated by arithmetic examples.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Pyrops candelaria is one of the common pests of fruit trees, but the research on the pathogenic microorganisms it may carry is very limited. Therefore, it is essential to reveal the pathogenic microbes it carries and their potential hazards. This study found a new virus from the transcriptome of P. candelaria, which was first reported in P. candelaria and named as PyCaV (Pyrops candelaria associated virus). RACE and bioinformatics assay revealed that the full-length of PyCaV is 10855 bp with the polyA tail, containing a single open reading frame (ORF) encoding a polyprotein consisting of 3171 amino acid (aa). The virus has a typical Iflavirus structure, including two rhv domains, a RNA helicase domain (HEL), a 3C cysteine protease domain (Pro), and a RNA-dependent RNA polymerase domain (RdRp). Further phylogenetic analysis revealed that this virus belongs to family Iflaviridae and sequence alignements analysis suggedted PyCaV is new member in unassigned genus of family Iflaviridae. Further in-depth analysis of virus-infection-part showed that PyCaV is distributing in the whole longan lanternfly, including its head, chest, and abdomen, but more PyCaV was identified in the chest. The distribution of PyCaV in different parts of P. candelaria was further explored, which showed that more PyCaV were detected in its piercing-sucking mouthparts and chest viscera. Statistical analysis showed that the PyCaV infection was affected by time and locations.

With the burgeoning growth of online retail, the issue of counterfeit products has become a significant threat to both consumer trust and brand integrity, posing challenges to sustainable market practices. Online retail platforms are promoted to redesign their channel structures and enhance brand traceability to tackle counterfeits using blockchain technology. To investigate the interactions between blockchain technology and the channel structures of online retail platforms, we design a game theory model incorporating a manufacturer with(out) blockchain participation selling products via an online retail platform that operates an agency channel and/or a reselling channel. We show that the critical trade-off of blockchain participation comprises the brand assurance effect of the blockchain, the channel competition intensification effect, and the blockchain adoption cost. The platform is capable of strategically designing the channel structure to encourage (while discouraging) blockchain participation by the manufacturer. Our analysis highlights the complementarity between blockchain participation and the channel structure. Furthermore, the effect of the consumer’s belief in the reselling channel, the commission fee in the agency channel, and the substitutability between channels are investigated in depth. The research provides valuable insights for online retail platforms and policymakers seeking to foster a sustainable and trustworthy e-commerce ecosystem.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

The paper describes the new method for image compression based on coordinated group signal transformation. The algorithm is a type of difference coding. Coordinated processing significantly simplifies the difference signal conversion scheme using a single group codec for all signals. The described method considers color channels as correlated signals of a multi-channel communication system. The specifics of the processed data required modification of the coordinated group processing algorithm. First, we changed how to calculate the difference signals to prevent data loss. Secondly, the group codec was supplemented with a neural network to improve the quality of reconstructed images. We considered the following types of neural networks: fully connected, recurrent, convolution, and convolution in the Fourier space. Based on the simulation results, it is best to use fully connected neural networks if the goal is to minimize processing delay time. These networks have a response time of 13 ms. On the other hand, if the priority is to improve quality in cases where delays are not critical, then convolution neural networks in the Fourier space should be used. These networks have a response time of 140 ms and are of significant interest.

As the world population grows, fulfilling the need for biomaterials in the healthcare system becomes increasingly important. Biomaterials, which include metals, polymers, ceramics, and composites, play an important role in the creation of medical devices that improve people's lives. The European Society for Biomaterials described biomaterials as non-biological materials used in medical devices to interact with biological systems. This definition has developed to encompass materials that treat, assess, or replace tissues or bodily functions. Biocompatibility, as defined by the FDA, is a key feature of biomaterials, as is the requirement to fulfil design requirements such as mechanical performance, geometry, and electrical control. Over the last decade, advances in regenerative medicine and tissue engineering have boosted biomaterials' usage in medical applications dramatically. Despite its promise, scientists, engineers, and physicians continue to face significant challenges due to the complexity of biomaterials. Biomaterials have various benefits, including biodegradability, non-toxicity, and biocompatibility, making them extremely useful for replacing, sustaining, or improving biological activities in damaged tissues. They are used in a wide range of applications, including tissue engineering implants, human tissue healing and regeneration, medication delivery systems, and biosensors. This study gives insights into the fundamental characteristics, case studies, and ethical issues associated with the usage and use of biomaterials, further examining their potential and significance in healthcare and medicine.

The studied solar pot is a recent invention, which gained a utility model protection in 2021 from the Hungarian Intellectual Property Office under patent number 5489. The device is made for environmentally friendly cooking or heating (by utilizing solar energy) of foods and liquids. Its structure is similar to a double pipe heat exchanger, it has an outer mantle and an inner cooking tank. The goals of the paper are proposing a new physically-based mathematical model describing the solar pot and carrying out computer experiments with it, assembling an experimental system of the pot connected with a solar collector and performing measurements on it. Based on the results, the solar pot can successfully be used for cooking or sterilizing foods or liquids during the studied time period, in Hungary.