The objective of this study is to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the equivalence ratio distributions and the injected fuel droplet behavior in the cylinder of the RCCI engine. The spray simulation was conducted by dividing two-part. First, the spray validation simulations progressed to find the spray-influenced factor of the test injector. Next, the engine simulations were performed with the spray-influenced factor obtained from spray validation simulations to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the injected fuel atomization and the equivalence ratio distributions. The introduced total heating value was fixed at 595J based on the lower heating value of diesel 14mg. The heating value of the premixed ethanol ratio varied from 0% to 40% based on the same total heating value in-cylinder in steps of 10%. It was revealed that when the premixed ethanol ratio based on the same total heating value in-cylinder was increased, the spray tip penetration value was reduced from the time after 4deg of diesel injection start because of the short injection duration by the small amount of diesel fuel. The SMD value was also more enormous up to 32.58% with increasing the premixed ethanol ratio because of the low kinetic energy of the injected fuel by the short injection duration and the slow evaporation of the injected fuel by the low cylinder temperature.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

Natural gas hydrate, also known as combustible ice and mainly composed of methane, it is identified as the potential clean energy in the 21th century. Due to its large reserves, gas hydrate can ease problems caused by energy resource shortage and has gained attention around the world. In this paper, we focus on the exploration and development of gas hydrate as well as discussing its status and future development trend in China and abroad, then we analyze its opportunities and challenges in China from four aspects: resource, technology, economy and police with five forces model and PEST method. The results show, China has abundance gas hydrate resource; however the backward technologies and inadequate investment has seriously hindered the future development of gas hydrate, so China should establish relevant cooperation framework and intuitional arrangement to attract more investment as well as breaking through technical difficulties to make gas hydrate commercialization as soon as possible.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

Reasonable allocation of production plans and saving the overall electricity cost are crucial for large manufacturing conglomerates, which is an effective way for conglomerates to realize open-source and cost-saving. This paper develops an optimization model of off-site industrial production scheduling for enterprises in response to the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's electric power and the difficulty of promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and different electricity prices in different places to optimize the scheduling of industrial production in different places. The model is embedded with two sub-models of the electricity price prediction model and distributed photovoltaic kWh cost model to complete the model parameters, in which the electricity price prediction model utilizes the LSTM neural network. The integrated model is then solved by the particle swarm algorithm. To verify the effectiveness of the model in solving the problem of off-site production scheduling on the demand side of electricity, the research team researched two off-site pharmaceutical factories belonging to the same large pharmaceutical company. Finally, the research data were substituted into the model for solving, and it was concluded that the optimization model could significantly reduce the cost of electricity consumption of the enterprise by about 7.9 %.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

We suppose that a Cooper pair (CP) will experience a damping force exerted by the condensed matter. A Langevin equation of a CP in two dimensional condensed matter is established. Following a method similar to Nelson's stochastic mechanics, generalized Schr\"{o}dinger equation of a CP in condensed matter is derived. If the CPs move with a constant velocity, then the corresponding direct current (DC) electrical conductivity can be calculated. Therefore, a Drude like formula of resistivity of CPs is derived. We suppose that the damping coefficient of CPs in two dimensional cuprate superconductors is a linear function of temperature. Then the resistivity and scattering rate of CPs turn out to be also linear-in-temperature. The origin of linear-in-temperature resistivity and Planckian dissipation in cuprate superconductors may be the linear temperature dependence of the damping coefficient of CPs.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

Gardening was an important part of the daily duties within several of the religious orders in Europe during the Middle Ages. The rule of Saint Benedict specified that the monastery should, if possible, contain a garden within itself, and before and above all things, special care should be taken of the sick, so that they may be served in very deed, as Christ himself. The cultivation of medicinal and utility plants was important to meet the material needs of the monastic institutions, but no physical garden has yet been found and excavated in either Scandinavia or Iceland. Especially the Cistercians were well known for being pioneer gardeners, but also other orders like the Benedictines and Augustinians practised gardening. The monasteries and nunneries operating in Iceland during medieval times are assumed to have belonged to either the Augustinian or the Benedictine orders. In Norway in addition other orders included the Dominicans, Fransiscans, Premonstratensians and Knights Hospitallers. Based on botanical investigations at all the Icelandic and Norwegian monastery sites, it is concluded that many of the plants found may have a medieval past as medicinal and utility plants, and with all the evidence combined, most probably were cultivated in monastery gardens.

More and more works are using machine learning techniques while adopting supervisory control and data acquisition (SCADA) system for wind turbine anomaly or failure detection. While parameter selection is important for modelling a wind turbine’s health condition, only a few papers have been published focusing on this issue and in those papers interconnections among sub-components in a wind turbine are used to address this problem. However, merely the interconnections for decision making sometimes is too general to provide a parameter list considering the differences of each SCADA dataset. In this paper, a method is proposed to provide more detailed suggestions on parameter selection based on mutual information. Moreover, after proving that Copula, a multivariate probability distribution for which the marginal probability distribution of each variable is uniform is capable of simplifying the estimation of mutual information, an empirical copula based mutual information estimation method (ECMI) is introduced for an application. After that, a real SCADA dataset is adopted to test the method, and the results show the effectiveness of the ECMI in providing parameter selection suggestions when physical knowledge is not accurate enough.

For offshore wind power generation, accessibility is one of the main factors that has great impact on operation and maintenance due to constraints on weather conditions for marine transportation. This paper presents a framework to explore the accessibility of an offshore site. At first, several maintenance types are defined and taken into account. Next, a data visualization procedure is introduced to provide an insight into the distribution of access periods over time. Then, a rigorous mathematical method based on finite state Markov chain is proposed to assess the accessibility of an offshore site from the maintenance perspective. A five-year weather data of a marine site is used to demonstrate the applicability and the outcomes of the proposed method. The main findings show that the proposed framework is effective in investigating the accessibility for different time scales and is able to catch the patterns of the distribution of the access periods. Moreover, based on the developed Markov chain, the average waiting time for a certain access period can be estimated. With more information on the maintenance of an offshore wind farm, the expected production loss due to time delay can be calculated.

Drilling vibrations has been identified as a key performance limiter that prevents successful energy transfer from the surface to the bit. The resultant irregular bit rotation speed causes drilling challenges like poor hole quality and reduction in rate of penetration to name a few. Amongst other vibration suppression techniques, active control of vibrations is widely used and recommended. Active control system utilizes a closed loop feedback control to continuously adapt to downhole vibrations detected at the surface. The system requires regular tuning and upgrades which is done experimentally before field deployment. The paper presents a PID based experimental tuning of horizontal and vertical strings for irregular RPM. In doing so, the paper highlights the need of having horizontal experimental setups for state-of-the-art PID tuning for downhole RPM. The settling time of irregular RPM for horizontal setup is found to be lower than the vertical configuration due to multiple contact points and increased friction coefficient.

Biological nanoparticles (NPs), such as extracellular vesicles (EVs), exosome-mimetic nanovesicles (EMNVs) and nanoghosts (NGs), are perspective non-viral delivery vehicles for all types of therapeutic cargo. Biological NPs are renowned for their exceptional biocompatibility and safety, alongside their ease of functionalization, but a significant challenge arises when attempting to load therapeutic payloads, such as nucleic acids (NAs). One effective strategy involves fusing biological NPs with liposomes loaded with NAs, resulting in hybrid carriers that offer the benefits of both biological NPs and the capacity for high cargo loads. Despite their unique parameters, one of the major issues of virtually any nanoformulation is the ability to escape degradation in the compartment of endosomes and lysosomes which determines the overall efficiency of nanotherapeutics. In this study, we fabricated all major types of biological and hybrid NPs and studied their response to acidic environment observed in endolysosomal compartment. In this study, we show that EMNVs display increased protonation and swelling relative to EVs and NGs in an acidic environment. Furthermore, the hybrid NPs exhibit an even greater response compared to EMNVs. Short-term incubation of EMNVs in acidic pH corresponding to late endosomes and lysosomes again induces protonation and swelling, whereas hybrid NPs are ruptured, resulting in the decline of their quantities. Our findings demonstrate that in an acidic environment, there is enhanced rupture and release of vesicular cargo observed in hybrid EMNVs that are fused with liposomes compared to EMNVs alone. This was confirmed through PAGE electrophoresis analysis of mCherry protein loaded into nanoparticles. In vitro analysis of NPs colocalization with lysosomes in HepG2 cells demonstrated that EMNVs mostly avoid endolysosomal compartment whereas hybrid NPs escape it over time. To conclude, (1) hybrid biological NPs fused with liposomes appear more efficient in the endolysosomal escape via the mechanism of proton sponge associated with scavenging of protons by NPs, influx of counterions and water, and rupture of endo/lysosomes, but (2) EMNVs are much more efficient than hybrid NPs in actually avoiding endolysosomal compartment in human cells. These results reveal biochemical differences across four major types of biological and hybrid NPs, and indicate that EMNVs are more efficient in escaping or avoiding endolysosomal compartment.

Rectal cancer presents a significant burden globally, often requiring multimodal therapy for locally advanced cases. Long-course chemoradiotherapy (LCRT) and short-course radiotherapy (SCRT) followed by surgery have been conventional neoadjuvant approaches. Recent trials favor LCRT due to improved local control. However, tumor distant recurrence remains a concern, prompting exploration of Total Neoadjuvant Therapy (TNT) as a comprehensive treatment strat-egy. Immune checkpoint inhibitors (ICIs) show promise, particularly in mismatch repair-deficient (dMMR) or microsatellite instability-high (MSI-H) tumors, potentially revolutionizing neoadjuvant regimens. Non-operative management (NOM) represents a viable alternative post-neoadjuvant therapy for selected patients achieving clinical complete response (cCR). Additionally, monitoring minimal residual disease (MRD) using circulating tumor DNA (ctDNA) emerges as a non-invasive method for treatment response assessment. This review synthesizes current evidence on TNT, ICIs, NOM and ctDNA, elucidating their implications for rectal cancer management and highlighting avenues for future research and clinical application.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

Green spaces take part a vital role in reducing the harmful effects occurred through the process of rapid urbanization. This study focuses on evaluating the change of green space and per capita green space in Colombo District, Sri Lanka in between 2008 and 2015 using Landsat images. The NDVI differencing method and classification method were used to detect the change of land cover. According to the results, a gradual decline of green space from 629.1km2 to 591.16km2 with a rate of 6.03% can be depicted. The change is considerable in Kaduwela, Moratuwa and Maharagama DSDs and quite better in the areas such as Avissawella, Homagama and Padukka. The per capita green space has been decreased from 272.361 m2 to 248.811 m2. Though these rates are very well higher than the UN, EU and WHO standards for the district, Colombo DSD do not comply with UN and EU standards. The case would turn into worst in 2025, as the predictions with current rates. Therefore, the study recommends taking immediate actions to make a greener city. Further, a tax system is proposed to get the attraction of the general public.

Frontotemporal dementia (FTD) is the second most common form of presenile dementia; however, its diagnosis has been poorly investigated. Previous attempts to diagnose FTD using quantitative electroencephalography (qEEG) have yielded inconsistent results in both spectral and functional connectivity analyses. This study aimed to introduce an accurate qEEG marker that could be used to diagnose FTD and other neurological abnormalities. We used open-access electroencephalography data from OpenNeuro to investigate the power ratio between the frontal and temporal lobes in the resting state of 23 patients with FTD and 29 healthy controls. Spectral data were extracted using a Fast Fourier Transform in the delta (1–4 Hz), theta (4–8 Hz), alpha (8–13 Hz), beta (13–32 Hz), and gamma (32–45 Hz) bands. We found that the spectral power ratio between the frontal and temporal lobes is a promising qEEG marker of FTD. Frontal/temporal (F/T) theta/alpha, alpha/theta, al-pha/gamma, and gamma/alpha showed a consistently high discrimination score for the diagnosis of FTD for different parameters and referencing methods. The study findings can serve as reference for future research focused on diagnosing FTD and other neurological anomalies.

There is little doubt that the efficacy of MnDPDP and its therapeutic improved counterpart Ca4Mn(DPDP)5 mainly depends on their MnSOD-mimetic activity when it comes to their potential use as rescue medicines, during e.g., acute myocardial infarction. However, pharmacokinetic considerations suggest that the efficacy of MnDPDP on Pt2+-associated neurotoxicity depends on another action of this drug. Electron Paramagnetic Resonance (EPR) studies have demonstrated that Pt2+ outcompetes Mn2+ and endogenous Zn2+ from binding to fodipir (DPDP), and hence suggest that the previously reported CIPN protective efficacy of MnDPDP is a result of chelation and elimination of Pt2+ by DPDP, which in turn suggests that Mn2+ is unnecessary for efficacy when it comes to oxaliplatin-associated CIPN.

In the modern power grid, characterized by the increased penetration of power electronics and extensive utilization of renewable energy, inverters-based power plants play a pivotal role as the principal interface of renewable energy sources (RESs) and the grid. Considering the stability characteristics of grid-following (GFL) inverters when the grid is relatively weak, the application of grid-forming (GFM) controls becomes imperative to enhance the stability of the entire power plant. Thus, there is an urgent need for suitable and effective models to study the interaction and stability of the paralleled inverters employing GFL and GFM controls. Thus, the small-signal modeling with full-order state space model and eigenvalues analysis is presented in this paper. First, the small-signal state-space model of the individual GFL and GFM inverters is obtained considering the control loop, interaction, reference frame, transmissions, and time delays. Then, the models of the individual inverter are extended to the hybrid inverters to study the effects of the GFM inverters on the small- signal stability of the entire system. And, the impacts of the inertia and damping are analyzed by the eigenvalues of the state-transition matrix. Case comprising three parallel GFL inverters and two GFL inverters with one GFM inverter, respectively, are studied to examine the effectiveness and accuracy of the model. Finally, the stability margin obtained from the eigenvalue analysis of the entire system is verified by time-domain simulations.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

This paper presents a theoretically and methodologically grounded GIS-based model for the measurement and mapping of an index of living conditions in urban residential areas across Sweden. Further, the model is compared and evaluated using the Swedish Police’s assessment of crime-exposed areas. The results indicate that geographically measured vulnerable living conditions overlap to a large extent with the areas assessed to be crime-exposed by the Swedish Police. Over 61% of the police-defined crime-exposed areas are characterized by vulnerable living conditions. The results also show that the overlap is not perfect and that there are vulnerable areas that are not included in the police’s assessment of crime-exposed areas, but which are nonetheless characterized by vulnerable living conditions that could negatively affect the development of crime. It is also proposed that the model and the mapped index of living conditions provide a more well-grounded scientific basis for the police's assessment work. As a first step, the Swedish police have implemented the model and the mapped index in the work process employed in their annual identification of crime-exposed or at-risk areas. In addition to assisting the police, the model and the mapped index could also be used to support other societal actors working with vulnerable areas.

Magnetron sputtering was used for producing Titanium Vanadium Nitride (TiVN) coatings on a variety of substrates. In this research, we investigate how changing the sputtering power and nitrogen: argon (N2:Ar) gas ratio affects the structural and tribological properties of TiVN coatings. Scanning Electron Microscope (SEM) technique was used to examine TiVN coating surface morphology. Both variants showed a gradual increase in the intensity of the TiVN coating's (111) and (222) peaks. TiVN coating's tribological properties were examined using a pin-on-disc tribometer with varying loads, speeds, and sliding distances. The wear rates of TiVN-coated brass pins were in the range of 2.5×10-4 to 9.14×10-4 mm3/Nm depending on load, sliding distance, and gas ratio variation, when compared to the wear rates of TiVN-coated brass pins deposited at various power, which ranged from 1.76×10-3 to 5.87×10-3 mm3/Nm.

The effects of CO₂-water-rock interactions on the mechanical properties of shale are essential for estimating the possibility of sequestrating CO₂ in shale reservoirs. In this study, uniaxial compressive strength (UCS) tests together with an acoustic emission (AE) system and SEM & EDS analysis were performed to investigate the mechanical properties and microstructural changes of black shales with different saturation times (10 days, 20 days and 30 days) in water dissoluted with sub-/super-critical CO₂. According to the experimental results, the values of UCS, Young’s modulus and brittleness index decrease gradually with increasing saturation time in water with sub-/super-critical CO₂. Compared to intact samples, 30-days’ saturation causes reductions of 56.43% in UCS and 54.21% in Young’s modulus for sub-critical saturated samples, and 66.05% in UCS and 56.32% in Young’s modulus for super-critical saturated samples, respectively. The brittleness index also decreases drastically from 84.3% for intact samples to 50.9% for samples saturated in water with sub-critical CO₂, to 47.9% for samples saturated in water with super-critical carbon dioxide (SC-CO₂). SC-CO₂ causes a greater reduction of shale’s mechanical properties. The crack propagation results obtained from the AE system show that longer saturation time produces higher peak cumulative AE energy. SEM images show that many pores occur when shale samples are saturated in water with sub-/super-critical CO₂. The EDS results show that CO₂-water-rock interactions increase the percentages of C and Fe and decrease the percentages of Al and K on the surface of saturated samples when compared to intact samples.

Background. On the subject of couple relationships, the literature pays attention to clinical, socio-anthropological profiles and psychological issues related to the capacity to love, empathy, satisfaction and happiness; however, there is a lack of a psychometric tool that can address the issue of couple stability in a structured and organized manner from an emotional-affective perspective. Objectives. To develop and adjust a psychometric tool that can be efficient and effective in solving the analysis of a coefficient of couple relational stability. Materials and Methods. Clinical interview, based on narrative-anamnestic and documentary evidence, and battery of psychometric tests. Results. In CGa, those who scored more than 20% differential at PLS-Q1 were 58/118 (69%), while in CGb they were 118/118 (100%). In therapy, in the CGa, the resolved cases were 58/58 (100%), while in the CGb, the resolved cases were 110/118 (93%). At the clinical interview, it was found that the 8/118 (7%) "resistant" patients had, according to the PICI-3 model, a diagnosis of borderline personality disorder (5/8, 63%), histrionic-narcissistic (2/8, 25%), and bipolar (1/8, 12%), and thus by their nature not very prone to therapeutic adherence. Conclusions. Perrotta Love Stability Questionnaire (PLS-Q1) is a psychometric tool that offers therapists the opportunity to explore the topic of couple relationship stability, helping them to better focus on patients' vulnerable emotional positions to construct the most appropriate and targeted clinical intervention

HIF-1α is a master regulator of oxygen homeostasis involved in different stages of cancer development. Thus, HIF-1α inhibition represents an interesting target for anti-cancer therapy. It was recently shown that HIF-1α interaction with NQO1 inhibits its proteasomal degradation, thus suggesting that targeting the stability of NQO1 could led to destabilization of HIF-1α as a therapeutic approach. Since the molecular interactions of NQO1 with HIF-1α are beginning to be unraveled, we review here our current knowledge on the intracellular functions and stability of NQO1, its pharmacological modulation by small ligands, and the molecular determinants of its roles as a chaperone of many different proteins including cancer-associated factors such as p53 and p73α. This knowledge is then discussed in the context of potentially targeting the intracellular stability of HIF-1α by acting on its chaperone, NQO1. This could result in novel anti-cancer therapies.

In the early decades of the 19th century, the deaf population in the eastern US and Canada was distributed across a vast area. After the 1817 founding of the American School for the Deaf (ASD) in Hartford, CT and the subsequent establishment of schools for the deaf in New York City (NYSD), Philadelphia, and many other US states, hundreds of deaf students called these schools home for several years. After leaving school, the early American Deaf community faced a challenge: How would the community maintain its social and linguistic ties across a vast geographical area once community members had dispersed to their hometowns? In this paper we analyze the attendance registries of two large gatherings of deaf individuals in Hartford in the years 1850 and 1854. These were among the largest and earliest known gatherings of deaf adults. The demographic data included in these registries open a window onto the evolving American Deaf community of the mid-19th century. Our analyses of the attendees’ school affiliations, ages, and marital status show that the signing community that had taken root among students at schools in Hartford and New York persisted among the adult graduates of those schools in towns across the northeastern US. We compare the places of residence of ASD and NYSD alumni in 1850 and 1854 to their hometowns when they first enrolled at school. Our comparisons suggest the mid-19th-century signing community had become more urban; it was centered to a greater extent in populous cities such as New York, Boston, and Hartford than had been true when the attendees had enrolled in school. We consider how the geography of deafness in the 19th century might inform our understanding of the sources of regional variation in ASL. We also consider how early cross-regional interactions may have inhibited such regional variation.

The hump feature is one of the major instabilities in pump-turbines. When pump-turbines operate in the hump region, strong noise and serious fluctuations can be observed, which are harmful to their safe and stable operation and can even destroy the whole unit as well as water conveyance system. In this paper, a low specific speed (n_q = 36.1 min⁻¹) pump-turbine model was experimentally investigated. Firstly, the hump characteristic was obtained under 19 mm guide vane opening conditions. More interestingly, when the hump characteristic was measured in two directions (increasing and decreasing the discharge), characteristic hysteresis was found in the hump region. The analysis of performance characteristics reveals that the hump instability is the result of Euler momentum and hydraulic losses, and different Euler momentum and hydraulic losses in the two development processes lead to the hysteresis phenomenon. Then, 12 pressure sensors were mounted in the different parts of the pump-turbine model to obtain the time and frequency characteristics. The analysis of the corresponding fast Fourier transform confirms that the hump characteristic is related to low-frequency (0.04–0.15 times rotational frequency) vortices. The occurrence and cessation of vortices depend on the operating condition and measurement direction, which contribute to the hysteresis feature. Finally, the type of the low-frequency vortices was analyzed through the cross power spectrum.

The abundant mechanical vibration energy in bridge road environment can be converted into electric energy by using the piezoelectric energy harvest technology, which could be an efficient way to provide energy required by the wireless sensor network in the bridge condition monitoring system. An autonomous energy harvesting system has been designed based on cantilever beams for sensing and acquiring the bridge vibration energy. After the analysis of the dynamic properties of the piezoelectric cantilever beam in the energy conversion, three kinds of interface circuits were compared through simulation and experimental results. It was shown that the VD interface circuit has less power loss. Furthermore, the proposed closed loop control method based on the VD circuit was simple, adaptive, and self-powered, which is suitable for the road energy harvesting application. Finally, the energy harvesting system based on VD circuit was realized with harvested power of around 0.8mW.

The concept of a Social License to Operate (SLO) has become increasingly important in the sustainability literature in recent years. Having its origins in the business discourse of the mining industry with respect to limiting opposition to mining projects, the notion of a social contract above and beyond legal requirements has since become applied across a number of different industries. Despite the concepts adoption confusion exists over the practices and outcomes of SLO, and particularly the nature of engagement. Given this situation it is surprising that not more attention to the role of marketing, and social marketing in particular, in operationalizing the concept. The paper discusses the potential of social marketing to contribute to SLO. Economic, political and social relations are complex in SLO and exchange is intricate in such relational environments. A community-based social marketing orientation is proposed as a means to improve exchange relations and enhance engagement. Seven models of SLO related social marketing models are discussed with community-based social marketing and adaptive co-marketing models being regarded as the most positive for the achievement of an SLO. Potential barriers to adoption of these approaches are noted.

In this study, the impact of the addition of high-aspect-ratio nano-ettringite to photocurable epoxy acrylate resin was explored, with a specific focus on the changes observed in viscosity, shrinkage, tensile strength, and elongation at the break of composites formed. Herein, the nano-ettringite samples were modified using KH-570. The 3 wt% or 6 wt% KH-570-modified and unmodified nano-ettringite were dispersed into the resin by ultrasonic treatment in conjunction with mechanical stirring. The grafting effects of nano-ettringite onto KH-570 were analyzed through scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric (TG) analysis, and Fourier transform infrared spectroscopy (FTIR). The results demonstrate that increased dosages of unmodified and modified nano-ettringite led to increased viscosity of the composite while reducing shrinkage. At the same dosage, the photocurable resin with modified nano-ettringite demonstrated a lower shrinkage and a higher tensile strength. Notably, when the amount of modified nano-ettringite was 3 wt%, the highest tensile strength of the composite was 64.61 MPa, presenting a 72.57% increase compared to the blank sample. Furthermore, the incorporation of modified nano-ettringite as a filler provides a new perspective for improving the performance of photocurable epoxy acrylate resin composites.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

A remarkable, unquestioned assumption in studies measuring the association between national average Intellectual Quotients (IQ) and Gross Domestic Products (GDP) per capita is that a supposedly immutable genetic factor (IQ) may be correlated with a markedly fluctuant one (the wealth of nations). Using historical GDP per capita data produced by the Maddison project, we find that, over history, the (Pearson productmoment) correlation coefficient (r) between average IQ and GDP per capita is highly variable and ranges from strong negative values to strong positive values. The correlation between national IQ and GDP per capita is thus a snapshot of the world order at some point in time, and historical data allow us to identify several other eras. Moreover, global GDP at any point in time is never difficult to predict in the first place. We show that arbitrary ad-hoc scores based on a country’s continental location present a more significant correlation with contemporary GDP per capita. We conclude this paper by a call to clarify the purpose of IQ studies in Macroeconomics and for the consideration of GDP as a time-series in this line of research.

In this work, two plasmonic structures with two different periodic nanostructures (nanodisk and nanostrip arrays) separated from the gold layer by an ultrathin dielectric Al2O3 layer are proposed, and their optical properties are simulated as 3-dimensional models using COMSOL Multiphysics software tool. The optical responses, such as the amplification of the electric field and the scattering, absorption and extinction cross sections of the two structures, are investigated and compared. The results show that both structures show strong field enhancement in their gap layer, and the structure with the periodic array of metal nanodisks shows stronger field enhancement and larger absorption, extinction, and scattering cross sections in its dipole resonance wavelength, which is defined as a bright plasmonic mode. In addition, some weaker resonant modes are observed for both structures and the reason for their generation is dis-cussed. The analysis of different possible modes in such structures is crucial for their application in various fields.

Metal nanoparticles are used to modify/enhance the properties of a polymer matrix for a broad range of applications in bio-nanotechnology. Here, we study the properties of polymer/gold nanoparticle (NP) nanocomposites through atomistic molecular dynamics, MD, simulations. We probe the structural, conformational and dynamical properties of polymer chains at the vicinity of a gold (Au) NP and a functionalized (core/shell) Au NP, and compare them against the behavior of bulk PE. The bare Au NPs were constructed via a systematic methodology starting from ab-initio calculations and an atomistic Wulff construction algorithm resulting in the crystal shape with the minimum surface energy. For the functionalized NPs the interactions between gold atoms and chemically adsorbed functional groups change their shape. As a model polymer matrix we consider polyethylene of different molecular lengths, from the oligomer to unentangled Rouse like systems. By computing the different properties the concept of the interface, and the interphase as well, in polymer nanocomposites with metal NPs are critically examined. Results concerning polymer density profiles, bond order parameter, segmental and terminal dynamics show clearly that the size of the interface / interphase, depends on the actual property under study. In addition, the anchored polymeric chains change the behavior/properties, and especially the chain density profile and the dynamics, of the polymer chain at the vicinity of the Au NP.

Glioblastoma, a deadly brain tumor, shows limited response to standard therapies like te-mozolomide (TMZ). Recent findings from the REGOMA trial underscore a significant survival improvement offered by regorafenib (REGO) in recurrent glioblastoma. Our study aimed to propose a 3D ex vivo drug response precision medicine approach to investigate recurrent glio-blastoma sensitivity to REGO and elucidate the underlying molecular mechanisms involved in tumor resistance or responsiveness to treatment. 3D glioblastoma organoids (GB-EXPs) obtained from 18 patients’ resected recurrent glioblastoma tumors were treated with TMZ and REGO. Drug responses were evaluated using NAD(P)H FLIM, stratifying tumors as responders (Resp) or non-responders (NR). Whole-exome sequencing was performed on 16 tissue samples, and whole-transcriptome analysis on 13 GB-EXPs treated and untreated. We found 35% (n=9) and 77% (n=20) of tumors responded to TMZ and REGO, respectively, with no instances of TMZ-Resp be-ing REGO-NR. Exome analysis revealed a unique mutational profile in REGO-Resp tumors compared to NR tumors. Transcriptome analysis identified distinct expression patterns in Resp and NR tumors, impacting Rho GTPase and NOTCH signaling, known to be involved in drug response. In conclusion, recurrent glioblastoma tumors were more responsive to REGO com-pared to TMZ treatment. Importantly, our approach enables a comprehensive longitudinal ex-ploration of the molecular changes induced by treatment, unveiling promising biomarkers in-dicative of drug response.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

A recently identified broiler myopathy known as wooden breast (WB) is predominantly found in the pectoralis major muscle of fast-growing broiler hybrids and is causing significant losses to the poultry industry. The aim of this study was to investigate the effects of WB syndrome on raw meat texture, purge loss and thermal properties of intramuscular connective tissue of pectoralis major muscle in the early post-mortem period. Results showed that WB muscles at 1d postmortem was associated with significantly increased stiffness and significantly increased purge loss compared to normal muscles (NB). However, at 3d postmortem, these parameters did not differ between the two groups. Insoluble and total collagen content was significantly higher in WB muscles compared to NB muscles, and the extractability of intramuscular connective tissue (IMCT) was also higher and remained stable in the early postmortem period. These were coincided with significantly lower protein content in the sarcoplasmic protein fraction and myofibrillar protein fraction of WB muscles compared to NB muscles (P < 0.05). The IMCT of these two groups showed different thermal properties, as the enthalpy of denaturation (ΔH) was significantly lower in WB muscles compared to NB muscles. The WB syndrome had a great effect on the texture and connective tissue properties of the meat compared to normal muscle, with a tendency for having a lower water holding capacity and higher raw meat hardness

The magnetic properties of 0.10 mm ultra-thin grain-oriented (UTGO) silicon steel and Fe-based amorphous (FBA) alloy under sinusoidal excitation were measured experimentally, and the magnetic field strength and iron loss of the two materials under different frequencies and magnetic densities were obtained. Based on the measured data, the magnetization and loss characteristics of the two materials were analyzed and compared. Furthermore, two Epstein square ring models of the same specification and different materials were designed, and the reliability of the models was verified. Then, the electromagnetic characteristics of the two Epstein square ring models at higher and lower frequencies were calculated by using the finite element method, and the iron loss was obtained and compared. The results show that the FBA alloy has good application characteristics at low frequency and low power, and the 0.10 mm UTGO silicon steel has good application characteristics at high frequency and high power. This research can provide important data basis to promote the application of these two materials in new energy equipment.

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.

The insufficient flexibility of the hybrid renewable integrated energy system (HRIES) makes it difficult to accommodate renewable energy with a high proportion. It is thus necessary to excavate its potential flexibility to improve its operational performance and consume renewable energy. This paper unlocks the adjustment potential of flexible buildings and builds a flexible thermal load regulation model according to the dynamic thermal characteristics and thermal comfort elastic interval of the buildings and a regulation model of the flexible electrical load based on its transferability, resectability, and rigidity. An operation optimization model, which incorporates multiple flexible load regulations and the variable load of devices, is then developed. A case study is presented to analyze the regulation and synergy mechanism in different types of flexible loads. Its results show a saturation effect between the flexible thermal and electrical loads in increasing renewable energy consumption and a synergy effect in decreasing the total cost. This synergy can reduce the total cost by 0.73%. Besides, the total cost can be reduced by 15.13%, and the renewable energy curtailment rate can decrease by 12.08% if the flexible electric and thermal loads are integrated into the operation optimization of HRIES.

Data4HumanRights training materials have been developed as open-source and tailored to limited resource settings where community data collectors often live and work. An overview of how the training material was developed together with community data collectors in Nigeria and Kenya is provided. The paper gives insights into the fundamental principles (i.e., inclusiveness, adaptive, limited resources, gender- and incentive-sensitive) and the structure of the open-access training materials. This resulted in 28 modules designed to be delivered in a face-to-face format in less than one day by a local trainer. To maximize adaptivity, the training modules can be mixed and matched (e.g., as individual modules or a learning path of several modules around a specific training need). The individual modules cover a range of methods and tools that are useful to human rights work, for example, documenting evictions, performing rapid needs assessments after acute crises, community profiling, and monitoring community development indicators. The training materials contain instructions for the facilitator(s) of the training and all necessary training materials to conduct the training. To maximize inclusivity, the training covers basic to advanced topics. Most training modules address basic training topics that can be optimally followed with a mobile phone (to avoid using a computer and printing handouts). The training was developed and implemented with local community groups in Nigeria and Kenya. The material is free to use, adapt, and translate into different contexts and languages.

Nowadays, wearable devices for human health monitoring are increasingly become popular and widely used. Typically, the wearable device is small size and operates with batteries. Therefore, the wearable device acquires bio-signals and transfers to smartphones or personal computers (PC) via WiFi/ Bluetooth for processing data. To reduce power consumption is one of the most important challenges of designing wearable devices. To solve this problem, the proposed signal quality valuation (SQV) method can be select the high-quality signal and reduce the transfer time to other devices. In this paper, the proposed SQV and data compression method rely on real-time PPG signals analysis to retain important information of PPG signal, improve performance and power consumption of PPG devices. Besides, we also proposed Heuristic rules for heart rate (HR) estimation with compression data. The experimental results show that the highest compression ratio (CR) is 387.8 with BIDMC Physionet database (sampling frequencies of 125 Hz) and HR error as 1.43 bpm for averaging absolute error (avAE), the standard deviation absolute error (sdAE as 0.4) and relative error mean (avRE as 0.019). The proposed real-time PPG measurement system (sampling frequency as 100/ 200/ 400 Hz) reduce power consumption and open the new structure for healthcare application systems

Understanding swash zone dynamics is of crucial importance for coastal management as the swash motion, consisting of the uprush of the wave on the beach face and the subsequent downrush, is responsible for driving changes the beach morphology trough sediment exchanges between the sub-aerial and sub-aqueous beach. Improved understanding of the probabilistic characteristics of these motions has the potential to allow coastal engineers to develop improved sediment transport models which, in turn, can be further developed into coastal management tools. In this paper, novel descriptors of swash motions are obtained by combining field data and statistical modelling. Our results indicate that the probability distribution function (PDF) of shoreline height (p(ζ)) and trough-to-peak swash heights (p(ρ)) measured at a high energy, sandy beach were both inherently multimodal. Based on the observed multimodality of these PDFs, Gaussian Mixtures are shown to be the best method to statistically model them. Further, our results show that both offshore and surf zone dynamics are responsible for driving swash zone dynamics, which indicates unsaturated swash. The novel methods and results developed in this paper, both data collection and analysis, could aid coastal managers to develop improved swash zone models in the future.

Introduction: The identification of some prognostic markers in head and neck cancers (HNC) is necessary for the stratification of the therapeutic approach with benefits in increasing treatment response rates and limiting the toxic side effects of treatments. Neutrophil-to-lymphocyte ratio (NLR), lymphocyte-to-monocyte ratio (LMR) and pallets-to-lymphocyte ratio (PLR) are currently validated as cheap and accessible biomarkers in different types of solid tumors. The purpose of the study was to evaluate the possible biomarker value of NLR, PLR and MLR recorded pre-treatment (radiotherapy/chemotherapy) for prognostic purposes in HNC. Materials and methods: The study included 190 patients with HNC included in the oncology record in the oncology outpatient clinic of the Craiova County Emergency Hospital starting from January 2002 and deceased until December 2022. Among them, 40 patients treated multimodally in the Clinic were included in the study of Oncology of the Craiova County Emergency Hospital for which the pre-treatment value (chemotherapy/radiotherapy) of NLR, PLR and MLR could be calculated. Overall survival (OS) values were correlated with NLR, PLR and MLR. Results: Median values for NLR, PLR and MLR were 6.15 (1.24-69), 200.79 (61.3- 1775.0) and 0.53 (0.12-5.5) respectively. In the study, the mean values for NLR, PLR and MLR of 2.88, 142.97 and 0.36 respectively were obtained. Median OS in the study group was 11 months (1-120). Although a negative Pearson`s correlation, the relationship between your variables was only weak, values R =.07, p=.67; R=.02, p=.31 and R=07, p=.62 being related with NLR, PLR and MLR respectively correlation with overall survival (OS). The median values of NLR, PLR and MLR were calculated (1.53, 90.32 and 0.18 respectively) for HNC cases with pre-treatment values of NLR <2 and for HNC cases with NLR values ≥6 (23.5, 232.78 and 0.79 respectively). Median OS for cases with NLR<2 and NLR≥6 were 17.4 and 13 months, respectively. Conclusions: The negative correlations of NLR, PLR and MLR with OS reported in the study are in accordance with the data reported in the literature for locally advanced recurrent and metastatic HNSCC cases. The comparative analysis of the data in the group with NLR<2 and NLR≥6 highlights an advantage of 4.4 months in median OS in favor of the group with low values of NLR. Being cheap and accessible, these markers could change the therapeutic approach even in centers with limited resources. The role of borderline NLR values as a prognostic factor in HNSCC must also be defined. PLR and MLR are less evaluated as biomarkers but the study demonstrates their potential to be used as prognostic biomarkers, it remains to be clarified if their inclusion in multivariable models along with NLR would bring a benefit

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

Urinary extracellular vesicles (uEV) hold non-invasive RNA biomarkers for genitourinary tract diseases. However, missing knowledge about reference genes and effects of pre-analytical choices hinder biomarker studies. We aimed to assess how pre-analytical variables (urine storage temperature, isolation workflow) affect diabetic kidney disease (DKD) -linked miRNAs or kidney -linked miRNAs and mRNAs (kidney-RNAs) in uEV isolates and to discover stable reference mRNAs across diverse uEV datasets. We studied nine raw and normalized sequencing datasets including healthy controls and individuals with prostate cancer or type 1 diabetes with or without albuminuria. We focused on kidney-RNAs reviewing literature for DKD-linked miRNAs from kidney tissue, cell culture and uEV/urine experiments. RNAs were analyzed by expression heatmaps, hierarchical clustering and selecting stable mRNAs with normalized counts (>200) and minimal coefficient of variation. Kidney-RNAs were decreased after urine storage at -20°C vs -80°C. Isolation workflows captured kidney-RNAs with different efficiencies. Ultracentrifugation captured DKD -linked miRNAs that separated healthy and diabetic macroalbuminuria groups. Eleven mRNAs were stably expressed across the datasets. Hence, preanalytical choices had variable effects on kidney-RNAs – analyzing kidney-RNAs complemented global correlation, which could fade differences in some relevant RNAs. Replicating prior DKD-marker results and discovery of candidate reference mRNAs encourages further uEV biomarker studies.

Osteoarthritis (OA) is the most common cause of pain and disability in adults. Dietary supplements such as undenatured type II collagen (UC-II) have shown to have some benefits in OA treatment. This study aimed to assess changes in pain levels among knee OA patients treated with UC-II for 6 months. Patients with knee OA of any grade were given a daily 40 mg dose of UC-II (CondroArtil®) as a dietary supplement for 6 months. Pain levels were measured using the visual analog scale (VAS) before starting UC-II 6 months thereafter. A total of 100 patients (62/38: male/female) with a mean age of 46.3 ± 13.8 years participated in the study. Most patients (60%) had mild to moderate OA (grade I or II). The UC-II supplementation was shown to significantly reduce pain levels (p<0.001) with a negative correlation between pain reduction and age (p=0.006) and BMI (p=0.049). The OA severity also affected pain reduction (p=0.011), with grade II OA experiencing higher pain levels. Previous physical therapy and food supplements had a significant impact on pain reduction (p=0.017 and p=0.012, respectively). The study suggests that UC-II is an effective treatment for reducing pain in patients with knee OA.

Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

Ovariectomy appears to be the best method to control the density of wild ungulate populations. The aim of the present study was to compare two surgical approaches, via the flank and midline, in mouflon’s ovariectomy in field conditions. Twenty female mouflons were enrolled in the study. The animals were divided randomly in two groups, Group F animals were gonadectomized via flank approach, while Group A animals were sterilized via linea alba access. The parameters evaluated were duration of surgery, duration of anaesthesia, recovery time, intra- and post-operative complications, intra-operative nociception and pain in the post-operative period. There were no intra- and post-operative complications. The evaluated parameters showed a very similar trend in both groups. Both techniques are found to be effective and safe in execution.

An active power dispatch method for a microgrid (MG) with multi-type loads, renewable energy sources (RESs) and distributed energy storage devices (DESDs) is the focus of this paper. The MG operates in a grid-connected model, and distributed power sources contribute to the service for load demands. The outputs of multiple DESDs are controlled to optimize the active power dispatch. Our goal with optimization is to reduce the economic cost under time-of-use (TOU) price, and to adjust the excessively high or low load rate of distributed transformers (DTs) caused by the peak-valley demand and load uncertainties. To simulate a practical environment, the stochastic characteristics of multi-type loads are formulated. The transition matrix of system state is provided. Then, a finite-horizon Markov decision process (FHMDP) model is established to describe the dispatch optimization problem. A learning-based technique is adopted to search the optimal joint control policy of multiple DESDs. Finally, simulation experiments are performed to validate the effectiveness of the proposed method, and the fuzzification analysis of the method is presented.

The valve controlled cylinder drive system is the most common type among hydraulic applications. The nonlinear behaviour in such system is inevitable when the valve spool around its null position [1] , Leaney [2] utilised component linking method to investigate the nonlinearities in a Moog valve controlled asymmetric cylinder drive system by simulation in Fortran, in which a generalised concept is introduced and validated by comparing to the experimental results. An factor is proposed in the generalised concepts to describe the asymmetric cylinder state, which is a constant when the cylinder in extending or retracting, but numerically calculated when the valve spool in the underlap region [2]. This paper utilises the component linking method to simulate the Moog valve controlled asymmetric cylinder drive system in Matlab Simulink, and proposed an analytical solution for factor when the valve spool in the underlap region.

The magnetic polarization tensor has a promising capability of determining the geometry and material properties of metallic samples. In this paper, a novel computation method is proposed to estimate the magnetic polarization tensors for the metallic samples using the boundary element method. In this method, the metallic sample is placed in a uniformly distributed magnetic field. Based on assumptions that the excitation frequency and/or the conductivity of the sample is very high, the metallic sample is regarded as a perfect electrical conductor (PEC). Therefore, the scattered field at a certain distance can be simulated. By utilising the boundary element method, the magnetic polarization tensor can be derived from the simulated scattered field. The theoretical calculation is presented and simulations and experiments have been carried out to validate the proposed method. The results from the simulation are matched with the analytical solution for the case of sphere samples. Moreover, there is a good agreement between the simulation results and the experimental results for the copper cylindrical samples.

This study aimed at testing the effectiveness of novel combinations of chemical and physical methods to control Prosopis juliflora, an invasive weed in the Moshi and Simanjiro districts of Nothern Tan-zania. Six different treatments including manual uprooting, glyphosate, bark chop with chemical application, two separate chemical mixtures and control were tested in a total of 32 plots, which represented two land use types (grazing land and farmland) found in the two districts. Each plot covered 20m×30m plot area. Two response variables (stem count and tree volume) were recorded to compare weed population density before and after treatment six months later. An analysis of the untreated control plots, showed that the inherent growth potential of P. juliflora was higher in Moshi than in Simanjiro district. The number of stems increased during the experiment for all six treatments showing that the P. juliflora population had not yet reached the local carrying capacity. For the manual control treatment, the increase was reduced compared to the untreated control. For all other treatments, the increase in stem count was on par with that in the untreated control or even higher. Thus, we conclude that only manual uprooting had a controlling effect but not to the extent that it eradicated P. juliflora. Thus, it is for P. juliflora as for weed control in general: weed control must be an ongoing effort.

The study comprehensively evaluated the prognostic roles of PLR, NLR, MLR, BLR, and ELR in patients with acute exacerbation chronic obstructive pulmonary disease (AECOPD). 619 patients with AECOPD and 300 healthy volunteers were retrospectively included into the study. The clinical characteristics containing laboratory findings of the AECOPD patients and the blood cell counts (CBCs) of the healthy volunteers were collected. Compared with the healthy volunteers, PLR, NLR, and MLR were elevated in COPD patients in stable condition, and were further ele-vated during exacerbation. ELR showed the opposite trend. PLR, NLR, and MLR were all posi-tively correlated with hospital LOS as well as CRP. In contrast, ELR was negatively correlated with hospital LOS as well as CRP. Elevated PLR, NLR, and MLR were all associated with more serious airflow limitation in AECOPD. Elevated PLR, NLR, and MLR were all associated with increased in-hospital mortality while Elevated ELR was associated with decreased in-hospital mortality in AECOPD. A nomogram was construct to predict in-hospital mortality in AECOPD. The nomo-gram had a C-index of 0.850 (95% CI: 0.799 – 0.901) with good predictive value and clinical ap-plicability. In summary, PLR, NLR, MLR, and ELR served as predictors for clinical outcomes in patients with AECOPD.

Laser marking on polymer composite surfaces can be difficult to contrast and cause readability problems for electronic decoding equipment on production lines due to poor interaction between the laser and the fibres used to reinforce these materials. This problem can be solved with the right choice of marking parameters, resulting in savings for companies by avoiding production problems such as rejection, scrap and customer complaints. The present work uses the PBT/glass fibre composite used in the manufacture of instrument panels for motorcycles. The tests were carried out with different laser marking parameters using a Nd: YAG laser. Subsequently, the laser-marked DMC codes were analysed using a Verifier to evaluate the quality according to the ISO/IEC 29158:2020 standard. A detailed analysis of these surfaces was also carried out to observe some physical and chemical changes using SEM microscopy and EDS spectroscopy. The optical analysis showed that the lower the radiation power and pulse frequency and the higher the marking speed, the weaker the laser marking and therefore the poorer the DMC code quality, which was confirmed by the SEM. EDS spectroscopy showed that the laser marking process did not affect the chemical changes on the sample surface.

This paper provides a comparative analysis of AES (Advanced Encryption Standard) and Salsa20 algorithm implementations, focusing on power consumption efficiency in passive RFID (Radio Frequency Identification) tags and ultra-low-power devices. The main objective of this work is to determine which of these algorithms is more suitable to operate in these types of devices. For this purpose, ASIC (Application-Specific Integrated Circuit) implementations of AES and Salsa20 based on low-power approaches were developed and their power consumption was evaluated. Results demonstrate that Salsa20 power consumption is lower than AES (2.82μW and 4.01μW, respectively - both in 0.18μm), indicating that Salsa20 is a better choice than AES for passive RFID tags.

Retinitis pigmentosa (RP) is a frequent cause of blindness among the working population in industrial countries, due to the inheritable death of photoreceptors. Though a gene therapy was recently approved for mutations in the RPE65 gene, there is generally no effective treatment presently. Previously, abnormally high-level cGMP and overactivation of its dependent protein kinase (PKG) have been suggested as causative for the fatal effects on photoreceptors, making it meaningful to explore the cGMP-PKG downstream signaling for more pathological insights and novel therapeutic target development purposes. Here we manipulated the cGMP-PKG system in degenerating retinas from the rd1 mouse model pharmacologically via adding a PKG inhibitory cGMP-analogue to organotypic retinal explant cultures. A combination of phosphorylated peptides enrichment and mass spectrometry was then applied to study the cGMP-PKG-dependent phosphoproteomics. We identified a host of novel potential cGMP-PKG downstream substrates and related kinases using this approach, and selected the RAF1 protein, which may act as both a substrate and a kinase, for further validation. We showed that the RAS/RAF1/MAPK/ERK pathway may be involved in retinal degeneration in a yet unclarified mechanism, thus deserving further investigation in the future.

Artificial intelligence (AI) is increasingly being used to improve the quality control of point-of-care diagnostics. This is caused by a number of factors, including the following: 1. AI can accelerate and improve testing accuracy. In comparison to humans, AI technology can review data more quickly and precisely, reducing errors and improving overall quality assurance. 2. When it comes to improving POC test findings on healthcare issues such as infectious diseases or medical crises such as heart attacks, AI can be used for sophisticated predictive analytics and modeling that aid in better decision-making. 3. Artificial intelligence facilitates process automation, increasing productivity and lowering labor costs in labor-intensive tasks such as testing and analyzing samples collected at point-of-care facilities. 4. The use of AI enables organizations implementing these solutions to gain insights from large volumes of raw diagnostic data generated faster and more accurately, allowing them to build solid frameworks around preventive care initiatives and significantly influence public health outcomes.5. Artificial intelligence (AI) has been demonstrated to be a useful tool for real-time monitoring systems that identify any problems with test results early so that they can be corrected before affected patients receive inaccurate diagnoses or treatment plans based on false information provided by diagnostic tests performed at points of care such as clinics or hospitals.Using these technologies would allow healthcare organizations to spend less on labor while still receiving exact diagnoses and rapid treatment delivery at a fraction of the cost that manual approaches required earlier.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

Artificial intelligence (AI) has emerged as a powerful tool for addressing the challenges posed by climate change and their impact on public health. By leveraging its capacity to analyze and predict climatic patterns, AI offers opportunities to enhance resource management and develop effective strategies for climate change mitigation. Moreover, AI can contribute to generating sustainable solutions that address the complex and interconnected nature of climate change. For example, AI can enable the optimization of energy consumption and facilitate the integration of renewable energy sources into existing systems. It can also support the development of climate models that provide timely and accurate predictions, enabling policymakers to implement proactive measures for disaster preparedness and response. Furthermore, AI-powered disease surveillance and mitigation techniques can improve public health outcomes by identifying patterns and trends in the spread of diseases in relation to climatic factors.However, the widespread adoption of AI-based solutions is not without challenges. Ethical concerns surrounding privacy and data ownership must be addressed, as the use of AI requires access to large datasets, raising potential privacy risks. Technical constraints, such as limited computational power and the need for sophisticated algorithms, also pose obstacles to the implementation of AI in climate change mitigation strategies. Furthermore, issues related to the accessibility and affordability of AI technologies must be resolved to ensure equitable distribution and maximize its potential impact on public health.To fully harness the power of AI in addressing climate change and improving public health outcomes, it is crucial to promote innovation, multidisciplinary collaboration, and open data science. Innovation can drive the development of new AI algorithms and technologies specifically tailored to address climate change challenges. Multidisciplinary approaches that bring together experts from diverse fields, including climate science, public health, and computer science, can foster a holistic understanding of complex systems and enable the design of comprehensive solutions. Finally, open data science practices, such as sharing data and algorithms, can facilitate collaboration and accelerate progress in mitigating climate change and its public health impacts.In conclusion, AI offers promising opportunities for effectively addressing climate change and its impact on public health. However, to fully realize its potential, it is essential to tackle ethical and privacy concerns, overcome technical constraints, and ensure accessibility and affordability. By promoting innovation, multidisciplinary collaboration, and open data science, we can unlock the transformative power of AI in mitigating climate change and improving public health outcomes.

In this paper, a continuous power management for a decentralized DC microgrid (DCMG) is proposed to achieve voltage regulation and power balance even under system uncertainty and voltage sensor failure. The DCMG system achieves a continuous power management through only the primary controller to reduce the computational burden of each power agent. To enhance the reliability and resilience of the DCMG system under voltage sensor failure, a DC bus voltage (DCV) sensor fault detection algorithm is proposed. In this algorithm, the DCV sensor failure is detected by comparing the measured DCV with the estimated DCV. When the power agent identifies the DCV sensor failure, it changes the operation properly according to the proposed control mode decision algorithm to maintain the stability of the DCMG system. When uncertain conditions such as the power variation of the distributed generations, sudden grid disconnection, DCV sensor failure, electricity price change, and critical battery status occur, the DCMG system is changed to transitional operation modes. These transitional operation modes are employed to transmit the power agent information to other agents without digital communication links (DCLs) and to accomplish power sharing even under such uncertain conditions. In the transitional operation modes of the DCMG system, the DCV levels are temporarily shifted to an appropriate level, enabling each power agent to detect the uncertainty conditions, and subsequently to determine its operation modes based on the DCV levels. Simulation and experimental results under different test conditions confirm the reliability and effectiveness of the proposed control scheme.

This study considers an application of the first-order Grey Markov Model to foresee the values of Italian power generation in relation to the available energy sources. The model is used to fit data from the Italian energy system from 2000 to 2022. The integration of Markovian error introduces a random element to the model, which is able now to capture inherent uncertainties and misalignments between the Grey model predictions and the real data. This application provides valuable insights for strategic planning in the energy sector and future developments. The results show good accuracy of the predictions, which provides powerful information for the effective implementation of energy policies concerning the evolution of energy demand in the country. Despite advancements, Italy’s 2032 energy mix will still significantly rely on fossil fuels, emphasizing the need for sustained efforts beyond 2032 to enhance sustainability.

Lake Malombe fish stocks have been depleted by chronic overfishing. Various management approaches (co-management, command control, and ecosystem-based management to fisheries) have been used to manage the fishery. However, the lack of an accurate predictive model has hampered their success. Therefore, we developed and tested a time series model for Lake Malombe fishery. The seasonal fish biomass and CPUE trends were first observed and both were non-stationary. The second-order differencing was applied to transform the non-stationary data into stationary. Autocorrelation functions (AC), partial autocorrelation function (PAC), and Akaike information criterion (AIC) were estimated, which led to the identification and construction of autoregressive integrated moving average (ARIMA) models, suitable in explaining the time series and forecasting. The results showed that ARIMA (1,2,1) provided a better prediction than its counterparts. The model satisfactorily predicted that by 2032, both fish biomass and CPUE will decrease to 3204.6 tons and 59.672 respectively, signifying the potential threat to Lake Malombe fishery. The model justified the necessity of taking precautionary measures to avoid the total collapse of the fishery.

Glioblastoma (GBM) is an aggressive and lethal primary brain tumor with restricted treatment options and a dismal prognosis. Oncolytic virotherapy (OV) has developed as a promising approach for GBM treatment. However, reaching invasive GBM cells may be hindered by tumor-surrounding, non-neoplastic cells when the OV is applied intratumorally. In this study, using a rodent GBM model and immunofluorescence analyses, we investigated the intranasal delivery of the oncolytic adenovirus (OAV) XVir-N-31 via virus-loaded, optimized shuttle cells. Intranasal administration (INA) was selected due to its non-invasive nature and the potential to bypass the blood-brain barrier (BBB). Our findings demonstrate that INA of XVir-N-31 loaded shuttle cells successfully delivers OAVs to the core tumor and invasive GBM cells, significantly prolongs the survival of GBM bearing mice, induces immunogenic cell death and finally reduces tumor burden, all this highlighting the therapeutic potential of this innovative approach. Overall, this study provides compelling evidence for the effectiveness of INA of XVir-N-31 via shuttle cells as a promising therapeutic strategy for GBM. The non-invasive nature of INA of OV-loaded shuttle cells holds great promise for future clinical translation. However, further research is required to assess the efficacy of this approach to ultimately progress in human clinical trials.

The paper investigates the issues of transliteration of Russian toponyms in a city environment and studies the efficiency of the Technical Reference Manual for the Standardization of Geographical Names published by the United Nations group of experts. The paper demonstrates the feasibility of the UN and Russian official transliteration standards and compares the suggested theoretical models with the practical applications found on the street signs, labels, maps, and other sources of navigation. The author presents a comprehensive account of practical transcription methods used in Moscow and offers a solution to a number of issues and discrepancies between popular transliteration models and their real-life application.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

The concept of {\it quantum ratio} emerged in the recent efforts to understand how Newton's equations appear for the center of mass (CM) of an isolated macroscopic body at finite body-temperatures, as the first approximation to quantum-mechanical equations. It is defined as $Q\equiv R_q/L_0$, where the quantum fluctuation range $R_q$ is the spatial extension of the pure-state CM wave function, whereas $L_0$ stands for the body's linear size (the space support of the internal, bound-state wave function). The two cases $R_q /L_0 \lesssim 1$ or $R_q/ L_0 \gg 1$, roughly correspond to the body's CM behaving classically or quantum mechanically, respectively. In the present note we elaborate more on this concept, illustrating it in several examples. An important notion following from introduction of the quantum ratio is that the elementary particles (thus the electron and the photon) are quantum mechanical, even when the environment-induced decoherence turns them into a mixed state. Decoherence and classical state should not be identified. This simple observation, further illustrationed by the consideration of a few atomic or molecular processes, may have significant implications on the way quantum mechanics works in biological systems.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

Retiring coal power plants can reduce air pollution and health damages. However, the spatial distribution of those impacts remains unclear due to complex power system adjustments and pollution chemistry and transport. Focusing on coal retirements in Pennsylvania (PA), we analyze six counterfactual scenarios for 2019 that differ in retirement targets (e.g., reducing 50% of coal-based installed capacity vs. generation) and priorities (e.g., closing plants with higher cost, closer to Environmental Justice Areas, or with higher CO₂ emissions). Using a power system model of the PJM Interconnection, we find that coal retirements in PA shift power generation across PA and the Rest of PJM region leading to scenario-varying changes in the plant-level release of several air pollutants. Due to air pollution chemistry and transport and socio-demographics, these changes in turn give rise to a reduction of 10 to 182 PM_2.5-attributable deaths in PJM across the six scenarios, with most reductions occurring in PA. Scenarios that reduce more coal power generation yield greater aggregate health benefits due to air quality improvements in PA and adjacent downwind regions. In addition, vulnerable populations—in both PA and Rest of PJM—benefit most in scenarios that prioritize plant closures in PA near Environmental Justice Areas. These results demonstrate the importance of considering cross-regional linkages and socio-demographics in designing equitable retirement strategies.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Mutation analysis of circulating tumor DNA (ctDNA) has applications in monitoring of colorectal cancer (CRC) patients for recurrence. Considering the low tumor fraction of ctDNA in cell-free DNA (cfDNA) isolated from blood plasma, the sensitivity of the detection method is important. Here, plasma DNA collected at diagnosis and follow-up from 25 CRC patients was analyzed using a multiplex superRCA mutation detection assay. The assay was also performed on genomic DNA (gDNA) from tumor and normal tissue from 20 of these patients. The lower limit of detection for most sequence variants was in the range of 10^-5, while when analyzing cfDNA from plasma with a typical input of 33 ng, the practical detection limit was ~10^-4 or 0.01% mutant allele frequency (MAF). In 17 of 19 patients with identified hotspot mutations in tumor gDNA, at least one hotspot mutation could be detected in plasma DNA at the time of diagnosis. The MAF increased at subsequent time points in four of the patients who experienced a clinical relapse. Multiplex superRCA analysis of the remaining six patients did not reveal any hotspot mutations. In conclusion, multiplex superRCA assays proved suitable for monitoring CRC patients by analyzing hotspot mutations in cfDNA, and dynamic changes in MAF were observed in patients with clinical relapse.

Fluidized beds are pivotal in the process industry and chemical engineering, with Computational Fluid Dynamics (CFD) playing a crucial role in their design and optimization. Challenges in CFD modeling stem from the scarcity or inconsistency of experimental data for validation, along with the uncertainties introduced by numerous parameters and assumptions across different CFD codes. This study navigates these complexities by comparing simulation results from the open-source MFIX and OpenFOAM, and the commercial ANSYS FLUENT, against experimental data. Utilizing a Eulerian-Eulerian framework and the kinetic theory of granular flow (KTGF), the investigation focuses on solid-phase properties through the classical drag laws of Gidaspow and Syamlal-O’Brien across varied parameters. Findings indicate that ANSYS Fluent, MFiX, and OpenFOAM can achieve reasonable agreement with experimental benchmarks, each showcasing distinct strengths and weaknesses. The study also emphasizes that both the Syamlal-O’Brien and Gidaspow drag models exhibit reasonable agreement with experimental benchmarks across the examined CFD codes, suggesting a moderated sensitivity to the choice of drag model. Moreover, the analysis were also carried out for 2D and 3D simulations, revealing that the dimensional approach impacts the predictive accuracy to a certain extent, with both models adapting well to the complexities of each simulation environment. The study highlights the significant influence of restitution coefficients on bed expansion due to their effect on particle-particle collisions, with a value of 0.9 deemed optimal for balancing simulation accuracy and computational efficiency. Conversely, the specularity coefficient, impacting particle-wall interactions, exhibits a more subtle effect on bed dynamics. This finding emphasizes the critical role of carefully choosing these coefficients to effectively simulate the nuanced behaviors of fluidized beds.

Growing interest is awarded to the digitalization of the building permitting use case and many works are developed about the topic. However, the subject is very complex and many aspects are usually tackled separately, making it very hard for traditional literature reviews to grasp the actual progress in the overall topic. This paper unveils the detailed state of the art in Digital Building Permitting (DBP) by critically analyzing the literature by means of a set of coding tags (research progress, implementation, affected DBP workflow steps, ambitions addressed) assigned by a multidisciplinary team. The mainly addressed aspects of the digitalization of building permits resulted to be the technologies to check the compliance of design proposals against regulations, followed by the digitalization of regulations. Lacking aspects are instead the involvement of officers, scalability of solutions and interoperability of data, intended both as data validation and as integration of geoinformation with building models.

An off-grid solar energy storage system (ESS) in National Pingtung University of Science and Technology (NPUST) was built and officially operated on Jun. 16th 2022. The system is installed in a 40' general container with PV panels of solar power 8250 W_p on top of the container. The ESS is made by repurposed lithium iron phosphate (LFP) batteries of 20 kWh capacity, where a battery management system (BMS) is adopted to ensured the safety of the battery system. An energy management system (EMS) is built to receive, process, analyse, store, and output the energy information. In this manuscript, a brief engineering report about the system is given.

In the face of escalating climate concerns and the push for sustainable development, the global shift towards renewable and decentralized energy systems presents new challenges and opportunities. This study investigates integrating decentralized energy production, particularly photovoltaic (PV) systems, into national energy planning, aiming to optimize energy strategies that balance local production and consumption with national objectives. By analyzing the Swiss energy model, the research employs the EnergyScope and REHO models to assess the strategic implications of decentralized versus centralized energy systems. Results show that a decentralized approach can significantly reduce PV installation needs to 35 GW, about 23% of potential capacity, and decrease annual system costs by 10% to CHF 1230 per capita. This strategy emphasizes local consumption, minimizes grid reinforcement demands, and leverages economic advantages while addressing overproduction challenges through effective energy storage and grid management. Conclusions underline the strategic value of combining centralized and decentralized methods for resilient and sustainable energy planning. The study contributes to the discourse on energy policy and infrastructure planning, advocating for a hybrid model that accommodates both local conditions and broader energy objectives, urging further research into climate impacts and technology integration for a comprehensive energy future.

The purpose of the study is to establish compliance of the design of the modernized car with the requirements for safe operation. An option has been proposed for upgrading a passenger wagon to a Mobile Diagnostic Complex for transporting a combined vehicle equipped with appropriate flaw detection equipment intended for rail diagnostics. The authors have established the most optimal option for locating the diagnostic vehicle on board the Mobile Diagnostic Complex (MDC) wagon, taking into account the additional load from the vehicle. To achieve this goal, the article developed a three-dimensional model of the supporting structure of the wagon body, proposed a methodology and presented the results of a study of the stress-strain state of the wagon body, taking into account the additional weight of the wagon. The article develops a methodology for studying the natural frequencies of vibrations of the wagon body and develops a three-dimensional model of the wagon for calculating dynamic indicators in the Universal Mechanism software package. Taking into account the previously carried out strength calculations, as well as in order to maintain the factory life cycle indicators of the supporting structure of the wagon body, it is recommended to use the model in the first version.

Abstract: Field studies with large-stemmed plants Artemisia dubia (wormwood) have been carried out at Vėžaičiai Branch LAMMC since 2018. According to three years of experimental results, annual dry matter (DM) yield varied from 7.94 to 10.14 t ha-1. Growing conditions, nitrogen ap-plication level and harvesting time had significant impacts on Artemisia dubia productivity. This article presents the results of research on preparation and use of Artemisia dubia biomass for en-ergy conversion and evaluation of technological-technical and environmental parameters of these plants utilization for solid biofuel. For experiments were used 6 variants of Artemisia dubia samples, which were grown in 2021: plants were cut three times and two fertilization options were used: (1) no fertilization and (2) fertilization with 180 kg ha-1 of nitrogen fertilizer. These harvested plants were chopped, milled and were pressed into the pellets. The physi-cal-mechanical characteristics (mоisture content, density and strength) of Artemisia dubia pellets were investigated. During this study, it was found that the density in dry mass (DM) of pellets ranged from 1119.86 to 1192.44 kg m-3. The pellet moisture content ranged from 8.80 to 10.49%. After testing of pellet strength, it was found that the pellets which were made from plant bio-mass PK-1-1, were the most resistant to compression, they withstood 560.36 N of pressure. Dry fuel lower heating value (LHV) of pellets was sufficiently high and was very close to pine saw-dust pellets, it varied from 17.46±0.25 MJ kg-1 to 18.14±0.28 MJ kg-1. The ash content of burned pellets ranged from 3.62±0.02% to 6.47±0.09%. Emissions of harmful pollutants – CO2, CO, NOx and unburnt hydrocarbons (CxHy) did not exceed the maximum permissible levels. Summariz-ing the results of investigated properties, cоmbustion and emissiоns of Artemisia dubia pellets, it can be concluded that this biofuel can be used for production of pressed biofuel and it is charac-terized by sufficient high quality, efficient combustion and permissible emissions to the envi-ronment.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

Aronia berries contain antioxidants that may have health promoting properties e.g., demonstrated positive effects on hypertension and dyslipidemia. There is a close link between cardiovascular diseases and hypertension and dyslipidemia, and cardiovascular events are the leading cause of death among subjects with T2D. Thus, we investigated the effect of 8 weeks supplementation with fermented aronia extract (FAE), non-fermented aronia extract (AE) and placebo on cardiovascular risk factors. The extracts were incorporated into snack bars containing 34 g (37%) aronia extract, or 17 g (21%) wheat bran for placebo, as well as raisins and coconut oil. The study was randomized and blinded with a triple-cross-over design. We examined the effects of aronia extracts on blood pressure, adiponectin and high-sensitive C-reactive protein and found no effects. After supplementation with placebo, there were significantly higher total-cholesterol, LDL-cholesterol, and HDL-cholesterol, with the placebo group showing significantly higher increases in total-cholesterol and LDL-cholesterol than the FAE group. Furthermore, we observed an increase in HDL-cholesterol in the AE group and an increase in triglyceride in the FAE group. Thus, we assume that raisins may have increased the participants’ cholesterol levels, however, with both AE and FAE having the potential to prevent this increase.

The increased adoption of information and communication technology for smart grid applications will require innovative cyber-physical system (CPS) testbeds to support research and education in the field. The groundbreaking CPS testbeds with realistic and scalable platforms have progressively gained interest in recent years, with electric power flowing in the physical layer and information flowing in the network layer. However, CPSs are critical infrastructures and not designed for testing or direct training, as any misbehaving in an actual system operation could cause a catastrophic impact on its operation. Based on that, it is not easy to efficiently train professionals in CPSs. Aiming to support the advancement and encourage the training of industry professionals, this paper proposes and develops a complete testbed with commercial tools. The testbed can reliably replicate the performance of smart grid systems and the main potential cyber threats that electric grids may face. The complex interdependencies between the cyber and physical domains are discussed in detail, and different case scenarios are presented, providing insightful guidelines for key features and design decisions for future smart grid testbeds.

In the recent decades, per- and polyfluoroalkyl substances (PFAS) have garnered widespread public attention due to their persistence in the environment and detrimental effects on the health of living organisms, spurring the generation of several transcriptome-centered investigations to understand the biological basis of their mechanism. In this study, we collected 2144 publicly available samples from 7 distinct animal species to examine the molecular responses to PFAS exposure and to determine if there are conserved responses. Our comparative transcriptional analysis revealed that exposure to PFAS is conserved across different tissues, molecules and species. We identified and reported several genes exhibiting consistent and evolutionarily conserved transcriptional response to PFAS, such as ESR1, HADHA and ID1, as well as several pathways including lipid metabolism, immune response and hormone pathways. This study provides the first evidence that distinct PFAS molecules induce comparable transcriptional changes and affect the same metabolic processes across inter-species borders. Our findings have significant implications for understanding the impact of PFAS exposure on living organisms and the environment. We believe that this study offers a novel perspective on the molecular responses to PFAS exposure and provides a foundation for future research into developing strategies for mitigating the detrimental effects of these substances in the ecosystem.

Information-Centric Networking (ICN) is a new paradigm of network architectures that focuses on content, rather than hosts, as first-class citizens of the network. As part of these architectures, in-network storage devices are essential to provide end users with close copies of popular content, to reduce latency and improve overall experience for the user, but also to reduce network congestion and load on the content producers. To be effective, in-network storage devices, such as content storage routers should maintain copies of the most popular content objects. Adversaries that wish to reduce this effectiveness can launch cache pollution attacks to eliminate the benefit of the in-network storage device caches. Therefore, it is crucial to protect these devices and ensure the highest hit rate possible. This paper demonstrates per-face popularity approaches to reducing the effects of cache pollution and improving hit rates by normalizing assessed popularity across all faces of content storage routers. The mechanisms that were developed prevent the consumers, whether legitimate or malicious, on any single face or small number of faces from overwhelmingly influencing the content objects that remain in the cache. The results demonstrate that per-face approaches generally have much better hit rates than currently used cache replacement techniques.

Based on hospital capacities, facts from past experience with the coronavirus disease 2019 (COVID-19) virus and the number of dark infections during the second wave (DII = 2D2), a reasonable limiting value of 140/D2 for the 7-day incidence per 100,000 persons (MSDIHT) and a second wave herd immunization threshold fraction value of 0.26 in Germany were calculated. If the MSDIHT is held below this limiting value, the German hospital system can cope with the number of new seriously infected persons without any triage decisions. On the basis of the SIRV epidemics model, the classical threshold values for herd immunization were calculated for 18 countries. For these countries, the dates regarding when herd immunization against the second COVID-19 wave will be reached were estimated

Acoustic Radiation Forced Impulse (ARFI) is an ultrasound integrated method, measuring stiff-ness by point shear wave elastography. To evaluate the diagnostic performance of ARFI of the liver and of the spleen, combined with spleen dimension and platelet count, in predicting clinical events in cirrhosis, a prospective and cross-sectional study was conducted between February 2017 and February 2021. The following ratio scores with ARFI measurements were performed: ALSDP (ARFI Liver-Spleen Diameter-to-Platelets ratio score), ASSDP (ARFI Spleen-Spleen Diam-eter-to-Platelets ratio score), ASSAP (ARFI Spleen-Spleen Area-to-Platelets ratio score), ALSAP (ARFI Liver-Spleen Area-to-Platelets ratio score). In 100 enrolled subjects, spleen ARFI, ASSDP, ASSAP, were significantly associated with high-risk oesophageal varices (HRVs) in the prospec-tive short- and long-term follow-up and in the cross-sectional study (p 0.7). ARFI-ratio scores can predict, in cirrhotic patients, the risk of developing HVRs in short and long-term period.

Background: Psoriasis is a chronic immune-mediated skin disease in which systemic inflammation plays an important role in the pathogenesis. In recent years, neutrophil-to-lymphocyte ratio (NLR), neutrophil-to-monocyte ratio (NMR), platelet-to-lymphocyte ratio (PLR), and systemic immune-inflammation index (SII) have been shown to be important indicators of inflammation. In this study, our aim is to investigate NLR, NMR, PLR, and SII levels in psoriasis patients treated with biologic agents. Method: Clinical and biochemical data of 209 patients who received systemic therapy for psoriasis were obtained by retrospectively reviewing their medical records. NLR, NMR, PLR, and SII values were calculated from the hemogram values of the patients. Results: In the third month of follow-up, the mean CRP, NLR, NMR, PLR, and SII values were significantly decreased compared to the baseline values. SII values showed strong positive correlations with NLR, NMR and PLR. Adalimumab, etanercept, and infliximab, which are TNF-α blockers, were observed to be more effective on PLR and NLR and especially NMR. Conclusion: NLR, NMR, PLR, and SII, which are data obtained from routine blood tests, can be used in the monitoring of treatment of psoriasis, especially with TNF- α blockers.