Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

Among magnetoelectric (ME) heterostructures, ME laminates of the type Metglas-like / PVDF (magnetostrictive+piezoelectric constituents) have shown the highest induced ME voltages, usually detected at the magnetoelastic resonance of the magnetostrictive constituent. This ME coupling happens because of the high cross-correlation coupling between magnetostrictive and piezoelectric material, and is usually associated with a promising application scenario for sensors or actuators. In this work we detail the basis of the operation of such devices, as well as some arising questions (as size effects) concerning their best performance. Also, some examples of their use as very sensitive magnetic fields sensors or innovative energy harvesting devices will be presented At the end, the challenges, future perspectives and technical difficulties that will determine the success of ME composites for sensor applications are discussed.

A large core size and bending resistance are very important properties of mid-infrared energy transfer fibers, but large core sizes usually lead to a deterioration of bending properties. A negative-curvature nested node-free anti-resonant hollow-core fiber (AR-HCF) based on quartz is proposed. It was made by adding a nested layer to a previous AR-HCF design to provide an additional anti-resonance region while keeping the gap between adjacent tubes strictly correlated to the core diameter to produce a node-free structure. These features improve the fiber’s bending resistance while achieving a larger core diameter. The simulation results show that the radial air-glass anti-resonant layer is increased by the introduction of the nested anti-resonant tube, and the weak interference overlap between the fiber core and the cladding mode is reduced, so the fiber core’s limiting loss and the sensitivity to bending are effectively reduced. When the capillary wall thickness t of the fiber is 0.71 μm, the core diameter D is 70 μm, the ratio of the inner diameter of the cladding capillary to the core diameter d/D is 0.62, and the diameter of the nested tube is d0=29 μm, the fiber has a lower limiting loss at the wavelength of 2.79 μm, and the limiting loss is 3.28×10-4 dB/m. At the same time, the optimized structure also has good bending resistance. When the bending radius is 30 mm, the bending loss is only 4.72×10-2 dB/m. To our knowledge, this is the first research to achieve an anti-bending low-loss micro-structure hollow fiber with a bending radius of less than 30 mm in the 2.79 μm band. An anti-bending low-loss anti-resonant hollow-core fiber with this structure constitutes a reliable choice for the light guiding system of a 2.79 μm band erbium laser therapy instrument.

Intracellular aggregates of the alpha-synuclein protein result in cell loss and dysfunction in Parkinson’s disease and atypical parkinsonism, such as multiple system atrophy and dementia with Lewy bodies. Each of these neurodegenerative conditions, known collectively as alpha-synucleinopathies, may be characterized by a different suite of molecular triggers that initiate pathogenesis. The mechanisms whereby alpha-synuclein aggregates in turn mediate cytotoxicity also remain to be fully elucidated. However, recent studies have implicated the cell-to-cell spread of alpha-synuclein as the major mode of disease propagation between brain regions during disease progression. Here, we review the current evidence for different modes of alpha-synuclein cellular release, movement and uptake, including exocytosis, exosomes, tunnelling nanotubes, glymphatic flow and endocytosis. A more detailed understanding of the major modes by which alpha-synuclein pathology spreads throughout the brain may provide new targets for therapies that halt the progression of disease.

In contemporary construction, the prevalence of vibration serviceability issues in lightweight and slender structures has become increasingly common, owing to advancements in building materials and construction methods. While these structures often meet the criteria for ultimate limit states, they can still elicit complaints due to excessive vibrations induced by human activity. To address this challenge, the Integral Resonant Control (IRC) technique has emerged as a favored approach for actively damping vibrations in various systems. This study introduces a fresh perspective on implementing a multi-input multi-output (MIMO) IRC scheme for active vibration control (AVC) specifically tailored for pedestrian structures utilizing inertial mass actuators. Building upon a common framework and design methodology outlined in previous research, this work presents a novel application of MIMO IRC for AVC. The designed controller is rigorously tested and implemented on a laboratory floor structure to validate its efficacy.

In this paper, a continuous power management for a decentralized DC microgrid (DCMG) is proposed to achieve voltage regulation and power balance even under system uncertainty and voltage sensor failure. The DCMG system achieves a continuous power management through only the primary controller to reduce the computational burden of each power agent. To enhance the reliability and resilience of the DCMG system under voltage sensor failure, a DC bus voltage (DCV) sensor fault detection algorithm is proposed. In this algorithm, the DCV sensor failure is detected by comparing the measured DCV with the estimated DCV. When the power agent identifies the DCV sensor failure, it changes the operation properly according to the proposed control mode decision algorithm to maintain the stability of the DCMG system. When uncertain conditions such as the power variation of the distributed generations, sudden grid disconnection, DCV sensor failure, electricity price change, and critical battery status occur, the DCMG system is changed to transitional operation modes. These transitional operation modes are employed to transmit the power agent information to other agents without digital communication links (DCLs) and to accomplish power sharing even under such uncertain conditions. In the transitional operation modes of the DCMG system, the DCV levels are temporarily shifted to an appropriate level, enabling each power agent to detect the uncertainty conditions, and subsequently to determine its operation modes based on the DCV levels. Simulation and experimental results under different test conditions confirm the reliability and effectiveness of the proposed control scheme.

This manuscript employs a surface stress-driven nonlocal model to explore the combined effects of long-range interaction and surface energy on higher vibration modes of functionally graded nanobeams. The nanobeam theory, based on Bernoulli-Euler kinematics, incorporates surface effects such as surface elasticity, surface residual stresses, surface density, and rotary inertia. Hamilton's principle is applied to derive the governing equation with size-dependent considerations. The main outcomes of a parametric investigation, considering four different kinematic boundary conditions (Cantilever, Simply-Supported, Clamped-Pinned, and Doubly-Clamped) while varying the nonlocal parameter and material gradient index, are presented and discussed. Additionally, the normalized natural frequencies for the second, third, fourth and fifth modes of vibrations are provided and analyzed for each case under study. The results underscore the model's effectiveness in capturing surface energy effects on the overall dynamic behavior of functionally graded Bernoulli-Euler nanobeams, offering a cost-effective approach for designing and optimizing nano-scaled structures.

In this work we outline a general method for calculating Auger spectra in molecules, which accounts for the underlying symmetry of the system. This theory starts from Fano’s formulation of the interaction between discrete and continuum states and generalizes this formalism to deal with the simultaneous presence of several intermediate quasi-bound states and several non-interacting decay channels. Our theoretical description is specifically tailored to resonant autoionization and Auger processes, and includes explicitly the incoming wave boundary conditions for the continuum states and an accurate treatment of the Coulomb repulsion. This approach is implemented and applied to the calculation of the K−LL Auger and autoionization spectra of ozone, which is a C2v symmetric molecule, whose importance in our atmosphere to filter out radiation has been widely confirmed. We also show the effect that the molecular point group, and in particular the localization of the core-hole in the oxygen atoms related by symmetry operations, has on the electronic structure of the Auger states and on the spectral lineshape by comparing our results with experimental data.

We provide a very general review of the resonant transmission line method for optical fiber problems. The method has been found to work seamlessly for a variety of difficult problems including elliptical and eccentric core fibers as well as “holey”, photonic crystal fibers. A latest version has been shown to offer great versatility with respect to cases of unconventional, inhomogeneous index profiles.

We investigate the shear quasinormal modes (QNMs) in the context of electron stars, focusing on the Lifshitz geometry and exploring the behavior in the small star limit. The study begins by analyzing the shear sector modes in the infrared (IR) Lifshitz limit, where the geometry approaches that of a pure Lifshitz space. We derive and solve the differential equations governing the shear modes, revealing the asymptotic behavior in terms of the Lifshitz exponent. In the special case of integer values of the exponent, we obtain analytic corrections to the solutions to extract hydrodynamical QNMs. We then explore the cases with a Lifshitz exponent equal to or greater than three, providing analytical corrections to the Lifshitz IR solutions. A special case with an exponent of two is also considered, leading to modified solutions. The study extends to finding hydrodynamical QNMs, emphasizing the role of the Lifshitz geometry. Further investigations involve the flux with real and complex frequencies, considering the off-shell Lagrangian and deriving conserved flux expressions. Our analysis focuses on the exterior of the star, modeled by the Reissner-Nordström-AdS geometry. The small star limit is examined, revealing interesting features in the behavior of fermionic excitations. In summary, we provide a detailed exploration of shear quasinormal modes in electron stars, shedding light on their behavior in Lifshitz geometry, small star limits, and the interplay between real and complex frequencies. Our findings contribute to our understanding of the dynamics of electron stars and their gravitational properties.

In this study, we use descriptive statistics and data visualization techniques to analyze datasets and identify patterns and relationships between bikeshare and other transportation modes. We also use regression analysis to quantify the impact of various factors on bikeshare usage. Our results indicate that bikeshare trips during the pandemic were much longer compared to pre-pandemic times. Moreover, usage of bikeshare differed by user group, with casual users showing a greater increase in usage compared to subscribers. We plotted bivariate choropleth maps to visualize the spatial distribution of changes in bikeshare usage. Our findings suggest that an increase in bikeshare travel was associated with a reduction in travel by ride-hailing and public transit, especially in the northern part of the city, indicating a potential replacement of other modes of transportation. On the western and southern boundary of the city, bikeshare had a complementary effect with other modes. Overall, the data acquired for this study provides a valuable opportunity to understand the behavior of bikeshare users in Chicago, the intercorrelation of bikeshare with other transportation modes, and the impact of infrastructure on bikeshare usage. The findings of this study can inform the design and implementation of bikeshare systems in other cities and contribute to the development of a more sustainable transportation system.

In this review, severe plastic deformation (SPD) is considered as a materials processing technology. The deformation mode is the principal characteristic differentiating SPD from common forming operations. For large plastic strains, deformation mode depends on the distribution of strain rates between continuum slip lines and can be varied from pure shear to simple shear. A scalar, invariant and dimensionless coefficient of deformation mode is introduced as a normalized speed of rigid rotation. On this basis, simple shear provides the optimum mode for structure modification and grain refinement whereas pure shear is "ideal" for forming operations. Special experiments and SPD practice confirm this conclusion. Various techniques of SPD are classified and described in accordance with simple shear realization or approximation. It is shown that correct analyses of the processing mechanics and technological parameters are essential for comparison of SPD techniques and the development of effective industrial technologies.

A new power receiving unit (PRU) is proposed in this paper for the resonant wireless power transfer (WPT), which is characterized by the capability of attracting high power from the power transmitting unit (PTU). The resonant WPT is designed for delivering the electrical power to the PRU attached on an electrical vehicle (EV) chassis 50cm away from a PTU installed on the ground. The proposed PRU uses only the passive elements such as inductors, diodes and the capacitors, which needs no initial power from the EV. It is then applicable for charging a battery to several hundred volts for even a first-time charging battery. At a switching frequency of the resonant WPT in the experiment being 4MHz, the proposed PRU behaves itself as a negative impedance converter (NIC) in the subharmonics of 4MHz. The NIC effect plus the subharmonic oscillation causes an instability current charging the battery connected to the PRU. In this paper, we simulated the PRU and performed the experiment. The experiment demonstrates a battery charging of 150W from 50cm away using three D-mode GaN HEMT transistors via the instability current ramp. The power transfer efficiency (PTE) improved as the power delivered to load (PDL) goes higher. The best power transfer efficiency (PTE) is 65% in the present findings. The simulation analysis shows that the circuit allows itself be used to much higher power transfer when it is implemented with more GaN HEMT transistors connected in parallel. The theoretical derivation of the PRU circuit is also used to support both the experimental and simulation results.

Black hole's quasinormal frequencies are basically the complex numbers which provide information about the relaxation of perturbations and depend on the characteristics of the spacetime and types of perturbations. In this paper, we evaluate the quasinormal modes of Hayward black hole in Einstein Gauss-Bonnet gravity, Hayward black hole in anti-de Sitter space (AdS) spacetime, and 4-dimensional black hole in Einstein-Lovelock gravity. By utilizing the WKB resonance technique, we examine the quasinormal modes frequencies $\omega$ by shifting the charge parameter $Q$ (it is also identified with the cosmological constant), circular harmonic index $l$, and mass of scalar field $m$. We also study the relaxation rate for those black holes and find out that the relaxation rate increases with increasing values of $Q$. We observe that real and imaginary components of the quasinormal modes are not linear functions as similar to Reisnner Nordstr\"{o}m-AdS. For large values of charge, quasinormal ringing becomes slower to settle down to thermal equilibrium and hence the frequency of the oscillation becomes smaller.

We describe a machine learning (ML) approach to process the signals collected from Covid-19 optical-based detector. Multilayer Perceptron (MLP) and Support Vector Machine (SVM) were used to process both raw data and feature engineering data, and high performances for qualitative detection of the SARS-CoV-2 virus with concentration down to 1 TCID50/ml has been achieved. Valid detection experiments contain 486 negative and 108 positive samples; and control experiments, in which biosensors without antibody functionalization were used to detect SARS-CoV-2, contains 36 negative samples and 732 positive samples. Data distribution patterns of the valid and control detection dataset, based on T-distributed Stochastic Neighbor Embedding (t-SNE), was used to study the distinguishability between positive and negative samples, and explain the ML prediction performances. This work demonstrates that ML can be a generalized effective approach to process signals and dataset of biosensors dependent on resonant modes as biosensing mechanism.

Pulsed electric fields of specific frequencies emitted by a glass plasma antenna tube have been shown to slow the growth of Acute Lymphoblastic Leukemia cells by as much as 43% when exposed to a series of frequencies between 156kHz and 162kHz. This narrow band of frequencies is termed a “Destructive Cancer Resonant Frequency Formant” (DCRFF).

This work presents an LC resonant passive wireless gas sensor with a novel structure designed to mitigate the negative impact of substrate. The LC sensor antenna with the new structure and the reader antenna were designed and optimized utilizing HFSS software to improve the transfer efficiency. The superiority of the designed structure compared with the general ones is highlighted and verified. The change in the substrate capacitance has essentially no interference with the parameters to be measured of the LC sensor. The sensor with the new structure was prepared by combining etching and sputtering methods. The structure of the ZnO nanowires (NWs) was characterized to confirm their high purity and wurtzite crystal structure. The LC gas sensors demonstrated excellent wireless sensing performance including a low detection limit of 0.5 ppm NO2, high response of 1.058 and outstanding stability at 180 °C. The developed new sensor structure not only prevented interference from the substrate during gas sensing testing, but also expanded the choice of sensor substrates, playing a critical role in the development of sensors based on LC resonance principle.

Foam concrete is a construction material with controllable low strength and untraditional physical properties. Its highly crushable nature leaves it a niche as an engineered energy-absorbing material in many value-added applications; however, fundamental understanding of the material properties is crucial. As foam concrete is highly cellularized and ductile, conventional concrete testing methods such as compression test are insufficient to characterize the key material attributes of foam concrete, especially when the foam density is low. The resonant frequency test (ASTM C215) is specified for evaluating dynamic Young’s modulus of normal concrete. Inspired by the non-destructive feature of this test, we investigate the possibility of using the resonant frequency test to continuously monitor the modulus build-up of foam concrete with age. For the representativeness of the samples, three variables are considered in material design—bulk density ranging from 0.4 to 1.2 g/cm3, water to cementitious materials ratio of 0.42 and 0.47, and fly ash replacement of 10 and 30% by weight of cement. After examining the different vibration modes, the fundamental transverse frequency is determined most suitable for interpreting the foam modulus. The experimental results demonstrate good accuracy of using this approach for the measurement of different samples. It is also confirmed that, for a given foam concrete, the foam modulus can be predicted by knowing the foam density and solid modulus of its base cement paste, which provides an important insight for the further studies and real applications of foam concrete.

We design an asymmetric nonlinear optical nanoantenna composed of a dielectric nanodisk and an adjacent nanobar. The proposed composite structure made of AlGaAs exhibits resonant response at both the fundamental and doubled frequencies. Being driven by the strong magnetic dipole resonance at the pump wavelength and a high-quality mode at the harmonic wavelength, the efficient second-harmonic radiation is generated predominantly along the vertical directions under the normally incident plane-wave excitation.

This paper proposes a single-stage asymmetrical half-bridge fly-back (AHBF) converter with resonant mode using dual-mode control. The presented converter has an integrated boost converter and asymmetrical half-bridge fly-back converter and operates in resonant mode. The boost-cell always operates in discontinuous conduction mode (DCM) to achieve high power factor. The presented converter operates simultaneously using a variable-frequency-controller (VFC) and pulse-width-modulation (PWM) controller. Unlike the conventional single-stage design, the intermediate bus voltage of this controller can be regulated depending on the main power switch duty ratio. The asymmetrical half-bridge fly-back converter utilizes a variable switching frequency controller to achieve the output voltage regulation. The asymmetrical half-bridge fly-back converter can achieve zero-voltage-switching (ZVS) operation and significantly reduce the switching losses. Detailed analysis and design of this single-stage asymmetrical half-bridge fly-back converter with resonant mode is described. A wide AC input voltage ranging from 90 to 264 Vrms and output 19 V/ 120 W prototype converter was built to verify the theoretical analysis and performance of the presented converter.

Recent studies have shown that the mechanical properties of bioinspired periodic composite materials can be strongly influenced by finite deformation effects, leading to highly nonlinear static and dynamic behaviors at multiple length scales. For instance, in porous periodic nacre-like microstructures, microscopic and macroscopic instabilities may occur for a given uniaxial loading process and, as a consequence, wave attenuation properties may evolve as a function of the microstructural evolution, giving it the designation of metamaterials. The numerical outcomes provide new opportunities to design bioinspired soft composite metamaterials characterized by high deformability and enhanced elastic wave attenuation capabilities given by the insertion of voids and lead cores.

Diagnostics and decomposition of atmospheric disturbances in a planar flow are considered and applied to numerical modeling results with the direct possibility to use in atmosphere monitoring especially in such strong events which follow magnetic storms. The study examines a situation in which the stationary equilibrium temperature of a gas may depend on a vertical coordinate, that seriously complicates the problem solution. The relations connecting perturbations for acoustic and entropy modes are analytically established and led to the solvable diagnostic equations. These perturbation structures, found as the equation solutions specify acoustic and entropy modes in an arbitrary stratified gas under the condition of stability. These time-independent diagnostic relations link gas perturbation variables of the acoustic and the entropy modes. Hence, they provide the ability to decompose the total vector of perturbations into acoustic and non-acoustic (entropy) parts uniquely at any instant within the all accessible heights range. As a prospective model, we consider the diagnostics at the height interval [120;180] km, where the equilibrium temperature of a gas depends linearly on the vertical coordinate. For such a heights range it is possible to proceed with analytical expressions for pressure and entropy perturbations of gas variables. Individual profiles of acoustic and entropy parts for some data, obtained by numerical experiment, are illustrated by the plots for the pure numerical data against ones obtained by the model. The total energy of a flow is determined for both approaches and its height profiles are compared.

Regular regimes of oil and oil products pipelines are studied. The problem is to develop an algorithm of effective pipeline system control that ensures the fulfillment of specified boundary conditions at the system boundaries. The product is pumped in batches, the flow is characterized by a change in temperature and pressure flow parameters over time. The developed solution method uses the principle of decomposition in the sense that each computational iteration is im-plemented in 3 stages, in three nested loops. The inner cycle is connected with the material bal-ance relations, at the next cycle the flow equations are introduced and the fulfillment of the 2nd Kirchhoff's law is monitored. If the flow process is significantly affected by temperature, then an external cycle is also implemented, correcting the solution so that the energy conservation equa-tion is satisfied. In the calculation procedure, some computational difficulties may arise, which consist in choosing an appropriate optimization method. On a specific example, the possibility of using various library programs to solve the problem was checked. The developed method is suita-ble for the analysis of systems of arbitrary topology. Since the method is not time-consuming, it can be recommended for online control of oil and oil products supply systems. The paper opens a new direction in the theory of hydraulic circuits. It uses both traditional methods of continuum mechanics and stochastic models.

The particulars of stimulus-response experiments done on dynamic biosystems clearly limit what one can learn and validate about their structural interconnectivity (topology), even when collected kinetic output data are perfect (noise-free). As always, available access ports and other data limitations rule. For linear systems, exponential modes, visible and hidden, play an important role in understanding data limitations, embodied in what we call dynamical signatures in the data. We show here how to circumscribe and analyze modal response data in compartmentalizing model structures – so that modal analysis can be used constructively in systems biology model building – for nonlinear (NL) as well as linear biosystems. We do this by developing and exploiting the modal basis for dynamical signatures in hypothetical (perfect) input-output data associated with a structural model – one that includes inputs and outputs explicitly – and for NL as well as linear biosystems. The methodology establishes model dimensionality (size, complexity) from particular data sets; helps select among multiple candidate models (model distinguishability); helps in designing new experiments to extract “hidden” structure; and helps to simplify (reduce) models to their essentials. For NL biosystems, results are not as comprehensive, similarly informative about their dominant dynamical properties, and unified with linear models on invariant 2-dimensional manifolds in phase space. Some automation of these highly technical aspects of biomodeling is also introduced.

We report the strong coupling between plasmonic surface lattice resonances (SLRs) and photonic Fabry-Pérot (F-P) resonances in a microcavity embedded with two-dimensional periodic array of metal-insulator-metal nanopillars. For such a plasmonic-photonic system, we show that the SLR can be strongly coupled to the F-P resonances of both the odd- and even orders, and that the splitting energy reaches as high as 138 meV in the visible regime. We expect that this work will provide a new scheme for strong coupling between plasmonic and photonic modes.

We discuss in detail a well known method for obtaining the frequencies of the normal modes of coupled harmonic oscillators that is based on the simultaneous diagonalization of two symmetric matrices. We apply it to some simple illustrative examples recently chosen for the presentation of an alternative approach based on a set of constants of the motion. We show that the traditional method is simpler, even in the case of equal frequencies. We also discuss a problem that commonly appears in elementary courses on quantum mechanics that also requires the diagonalization of two symmetric matrices.

Induction heating (IH) technology is widely recognized and utilized in residential applications due to its high efficiency and safe operating characteristics. Resonant inverter circuits are widely used in IH systems because of their high efficiency and ability to perform soft-switching. Among the various resonant inverters used in IH systems, the single-switch quasi-resonant (SSQR) inverter topology is typically preferred for low-cost and low-output-power applications. Despite its cost advantage, the SSQR topology has a relatively narrow soft-switching range, which can be unstable depending on the electrical parameters of the load and the resonant converter circuit. Accurately determining the capacitance value of the resonant capacitor and the inductance value of the induction coil, which are the key circuit elements of the SSQR induction cooker, is crucial for designing a reliable, efficient, and durable cooking system. In other words, there exists a critical relationship between the resonant converter circuit parameters, load characteristics, and safe operating conditions. Additionally, when considering closed-loop control methods used for power control and safety, selecting appropriate resonant circuit elements becomes vital in ensuring both reliable and efficient operation. This paper focuses on a novel and simplified design method for the SSQR inverter utilized in household appliances. The proposed method and its advantages in terms of the safe operating area of the switch are theoretically investigated and verified through simulations and prototype circuits.

Single nanowires (NWs) are of great importance for optoelectronic applications, especially solar cells serving as powering nanoscale devices. However, weak off-resonant absorption can limit its light-harvesting capability. Here, we propose a single NW coated with the graded-index dual shells (DSNW). We demonstrate that with appropriate thickness and refractive index of the inner shell, the DSNW exhibits significantly enhanced light trapping compared with the bare NW (BNW), and the NW only coated with the outer shell (OSNW) and the inner shell (ISNW), which can be attributed to the optimal off-resonant absorption mode profiles due to the improved coupling between the reemitted light of the transition modes of the leak mode resonances of the Si core and the nanofocusing light from the dual shells with the graded refractive index. We found that the light absorption can be engineered via tuning the thickness and the refractive index of the inner shell, the photocurrent density is significantly enhanced by 134% (56%, 12%) in comparison with that of the BNW (OSNW, ISNW). This work advances our understanding of how to improve off-resonant absorption by applying graded dual-shell design and provides a new choice for designing high-efficiency single NW photovoltaic devices.

Microbolometer is the most common uncooled infrared technique that allows to achieve 50mK-temperature resolution on the scene. However, this approach has to struggle with both the self-heating inherent to the resistive readout principle and the 1/f noise. We present an alternative approach that consists in using micro / nanoresonators vibrating according to a torsional mode, and whose resonant frequency changes with the incident IR-radiation. Dense arrays of such electromechanical structures were fabricated with a 12µm-pitch at low temperature allowing their integration on CMOS circuits according to a post-processing method. H-shape pixels with 9 µm-long nano-rods and a cross-section of 250 × 30 nm² were fabricated to provide large thermal responses, whose experimental measurements reached up to 1024 Hz/nW. These electromechanical resonators featured a noise equivalent power of 140pW for a response time of less than 1 ms. To our knowledge, these performance are unrivaled with such small dimensions. We also showed that a temperature sensitivity of 20 mK within 100ms-integration time is conceivable at a 12µm-pitch by co-integrating the resonators with their readout electronics and suggesting a new readout scheme. This sensitivity could be reached at short-term by depositing on top of the nano-rods a vanadium oxide layer having a phase-transition that could possibly enhance the thermal response by one order of magnitude.

The Bardeen black hole stands as the first model of a regular black hole. Driven by the interpretations of Bardeen spacetime as a quantum-corrected Schwarzschild-like solution, we study quasinormal modes of a massive scalar field within this context. We have found that the damping rate of the massive scalar field decreases as the mass grows, leading to appearance of the arbitrarily long lived modes. or quasiresonances. The massive term in the Bardeen case is distinctive also in two other respects. First, the overtones deviate from their massless limit at a much smaller rate than the fundamental mode, when the mass is turned on. This behavior overlaps with the outburst of overtones due to the quantum deformation near the event horizon. Finally, integration in the time-domain shows that the oscillatory tails decay as $\sim t^{-(\frac{8}{6}+\ell)}$ at intermediate times and as $\sim t^{-1}$ at asymptotically late times, which is different from the Reissner-Nordstr\"om and Schwarzschild limits.

Hippocampus plays a crucial role in spatial and episodic memory. The acquisition of new memories is impossible without participation of the hippocampus. There are two main functional states or “modes” of the hippocampal activity, theta and non-theta state. They have different behavioral correlates and clearly different spectral content of the LFPs and neuronal spiking. Hippocampal theta state is present under active exploratory behavior, locomotion, cognitive situations requiring attention and REM sleep. Slow-wave sleep and quiet wakefulness (immobility, eating, grooming) represent the non-theta hippocampal state. The nodal point for the regulation of hippocampal activity is the MS. The activation or suppression of different types of MS cells appears to be responsible for controlling hippocampal theta and non-theta states. Functional coupling between MS neurons and hippocampal interneurons varies in a state-dependent manner.

Every (multimedia) service needs to be accessible. Accessibility for multimedia content is typically provided by means of access services, of which subtitling is likely the most widespread one. Up to date, many recommendations and solutions for subtitling classical 2D audiovisual services are available. Likewise, recent efforts have been devoted to devising adequate subtitling solutions for VR360 video content. This paper, for the first time, goes a step beyond, by exploring two key requirements to fulfill remaining challenges towards efficiently subtitling 3D Virtual Reality (VR) content: presentation modes, and guiding methods. By leveraging insights from earlier work on VR360 content, the paper proposes novel presentation modes and guiding methods to not only deal with the freedom to explore the omnidirectional scenes, but also with additional specificities of 3D VR compared to VR360 content: depth, 6 Degrees of Freedom (6DoF), and viewing perspectives. The obtained results prove that always-visible and a novel proposed comic-style presentation mode are far more appropriate than state-of-the-art fixed-positioned subtitles, mainly in terms of immersion, ease and comfort of reading, and identification of speakers, when applied to professional pieces of content with limited displacement of speakers and with limited 6DoF (i.e. users are not expected to largely navigate around the virtual environment). Likewise, even in such limited movement scenarios, the results show that the use of indicators (arrows), as guiding methods, is well received. Overall, the paper provides relevant insights and paves the way toward efficiently subtitling 3D VR content.

In this paper, a voice coil motor (VCM) actuated fast tool servo (FTS) system is developed for diamond turning. To guide motions of the VCM actuator, a crossed double parallelogram flexure mechanism is selected featuring totally symmetric structure with high lateral stiffness. To facilitate the determination of the multi-physical parameters, analytical models of both electromagnetic and mechanical systems are developed. The designed FTS with balanced stroke and natural frequency is then verified through the finite element analysis. Finally, the prototype of the VCM actuated FTS is fabricated and experimentally demonstrated to have a stroke of ±59.02 μm and a first natural frequency of 253 Hz. By constructing a closed-loop control using PID controller with the internal-model based resonant controller, the error for tracking a harmonic trajectory with ±10 μm amplitude and 120 Hz frequency is obtained to be ±0.2 μm, demonstrating the capability of the FTS for high accuracy trajectory tracking.

We report on a 2D-gap surface plasmon metasurface based composed of a bottom metal layer, middle insulator layer, and top metal nanostructure of gold nanoblocks (nanoantennas). The proposed structure enables us to generate simultaneous multi plasmonic resonances and offers the possibility to tune them, within the near-infrared domain. The simplicity of the metasurface makes it promising for compact optical platforms based on reflection mode operation with potential application in multi-channel biosensors, second-harmonic generation, and multi-wavelength surface-enhanced spectroscopy among other interesting fields

This article addresses a challenge modeling novices face in model conceptualization: the recognition of behavior modes. Despite behavior modes being at the heart of system dynamics modeling, there is no unifying taxonomy for them, making them harder to learn for beginners. The article proposes criteria a taxonomy should satisfy, critically reviews previous taxonomies in the literature, and then introduces a new consistent taxonomy based on slope and curvature with mode names that refer only to visual cues and free of references to prior mathematical or domain-specific knowledge. Evidence from an exploratory experiment suggests that novices actually have difficulties classifying curves when using previous taxonomies. Links from these elementary modes to analogous terms in other taxonomies in diverse disciplines allow this taxonomy to be related to other ones. The article concludes by mentioning relevant limitations and future steps.

Stabilization of planar premixed flame front on a lattice (porous) burner is considered. It is rigorously mathematically proved that there exist two different stabilization regimes: one with flame front located nearby the surface of the burner, and another with flame front located inside the lattice. These two regimes result in qualitatively different gas temperature profiles along the flow, that is monotonic and non-monotonic, respectively. Boundary between the two regimes is described in terms of dependence of the lattice solid material temperature on flow Peclet number. Likewise temperature profiles, such dependencies may be both monotonic and non-monotonic. Transition between the two types of dependencies is controlled by Arrhenius number. Conclusions of the study are supported by numerical analysis. They also compare favourably with available experimental data. Novelty of the present approach is fundamentally rigorous analytical analysis of the problem.

The phonon modes in YBa₂Cu₃O_7-δ and YBa_2-xLa_xCu₃O_7-δ systems have been systematically studied by Raman spectroscopy. The new phonon modes of 104 cm^-1, 94 cm^-1, and 89 cm^-1 were found in all these samples. A crude estimate about the wavenumber of the collective vibration of the stable CuO2 plane was given in this paper. The standard deviations of the new phonons in YBa₂Cu₃O_7-δ and YBa_2-xLa_xCu₃O_7-δ systems were discussed. The results of the calculation indicated that the 104 cm^-1 mode probably stands the c-direction collective vibration of the stable CuO2 plane, the 94 cm^-1 mode stands the a-direction vibration, and the 89 cm^-1 mode stands b-direction vibration. The relevance between these phonons and the superconductivity was discussed. It is found that, as the T_c decreased, the 104 cm^-1 mode and the 94 cm^-1 mode softened, and the 89 cm^-1 mode hardened slightly.

This study investigates the impact of narrow-band terahertz pulses on the ferroelectric order parameter in Ba0.8Sr0.2TiO3 films on various substrates. The 375 nm thick BST film on an MgO (001) substrate exhibits enhanced THz-induced second harmonic generation when excited by THz pulses with a central frequency of 1.6 THz, due to the resonant excitation of the soft phonon mode. Conversely, the BST film on a Si (001) substrate shows no enhancement, due to its polycrystalline state. The 800 nm thick BST film on an MgO (111) substrate demonstrates maximum of second harmonic generation signal when excited by THz pulses at 1.8 THz, that is also very close to it`s soft mode frequency (1.9 THz). Notably, the frequency spectrum of the BST/MgO (111) film reveals peaks at both the fundamental and doubled frequencies, highlighting the quadratic dependence of SHG intensity on the THz pulse's electric field strength.

Six mode shapes, including bending and torsion, were documented for five different basketball rims and backboards at the United States Military Academy, West Point, New York, USA. The frequency and damping ratio of each mode shape were also determined. The empirical process began with the time-domain excitation and response of each rim-backboard system. The impulse of excitation came from an impact hammer separately applied to sequentially, to each node. The sinusoidal response was gathered from an accelerometer at a fixed location, node 1. Each time-domain excitation-response was then converted to a frequency domain Bode plot for each node by a B&K 2034 Signal Analyzer, giving transfer functions of output/input versus frequency. Structural Measurements System (SMS) Software was used to fit mode shapes to the Bode plots. Each of the six mode shapes were fitted to the Bode plots of each node at a specific modal frequency. Each of the six mode shapes were a function of the locations of the nodes, and the Bode plot gathered at each node. The first and second modes were critical for showing that the Energy Rebound Testing Device statistically correlated with the energy transferred to the rim and backboard. A known perturbation mass was selectively attached to the rim, to help isolate the dynamic masses and spring rates for the rim and backboard, to ascertain the kinetic energy transferred to the rim had a 95.67% inverse correlation with rim stiffness.

In this study, we seek to analyze and numerically evaluate a plasmonic sensor. To form the sensor structure, we use several amplifiers, such as two rings attached to each other and a cavity, as well as two metal insulating metal waveguides (MIM). At the beginning of this simulation, we must examine the resonant wavelengths and the refractive index of the resonators using the finite difference time domain method. By changing the refractive index and changing the dimensions of the cavity and the rims, we seek to investigate the sensor performance and the conduction characteristics of the plasmonics and to obtain the effect of these parameters. To evaluate the sensor performance, we calculate the three factors of sensitivity coefficient S, quality factor Q and figure of merit (FOM), here we reach the sensitivity of 987.6 nm / RIU. Such a plasmonic sensor with a simple framework and high optical resolution can be very useful for sensor systems on optical circuits.

A new utilization of entropy in the context of buckling is presented. The novel concept connecting strain energy and entropy for a pin-ended strut is derived. This concept rationalizes the ranking of buckling modes based on strain energy under the assumption of given entropy. By assigning identical entropy to all buckling modes, they can be ranked according to their deformation energy. Conversely, with identical strain energy assigned to all modes, ranking according to entropy is possible. Decreasing entropy was found to represent the scaling factors of buckling modes that coincide with the measurement of initial out-of-straightness imperfections in IPE160 beams. Applied to steel plane frames, scaled buckling modes can be used to model initial imperfections. It is demonstrated that the entropy (scale factor) for given energy roughly decreases with the inverse square of the mode index. For practical engineering, the study presents the possibility of using scaled buckling modes of steel plane frames to model initial geometric imperfections. Entropy proves to be a valuable complement to strain energy in structural mechanics.

Recently massless test scalar field perturbations of the holonomy corrected black holes [Z. Moreira et. al. Phys. Rev. D 107 (2023) 10, 104016] were studied in order to estimate quantum corrections to the quasinormal spectrum of a black hole. Here we study both the fundamental mode and overtones of scalar, electromagnetic and Dirac fields with the help of the Leaver method and higher order WKB formula with Pad\'e approximants. We observe that the overtones depend on the geometry near the event horizon, while the fundamental mode is localized near the peak of the potential barrier, what agrees with previous studies. We showed that unlike a massless field, the massive one possesses arbitrarily long lived modes. We also obtain the analytical eikonal formula for quasinormal modes and its extension beyond eikonal approximation as a series in powers of $1/\ell$, where $\ell$ is the multipole number.

In this paper, we introduce the application of Type-I fuzzy inference systems (FIS) as an alternative to improve the prioritization in the FMECA analysis applied in cyber-power grids. Classical FMECA assesses the risk level through the Risk Priority Number (RPN). The multiplication between three integer numbers computes this, called risk factors, representing the severity, occurrence, and detectability of each failure mode and are defined by a team of experts. The RPN does not consider any relative importance between the risk factors and may not necessarily represent the real risk perception of the FMECA team members, usually expressed by natural language; this is the main FMECA shortcoming criticized in the literature. Our approach considers fuzzy variables defined by FMECA experts to represent the uncertainty associated with the human language and a rule base consisting of 125 fuzzy rules to represent the risk perception of the experts. To test our approach, we select a cyber-power grid previously analyzed by the authors using the classical FMECA. The results reveal our proposed fuzzy approach as promissory to represent the uncertainty associated with expert knowledge and to perform an accurate prioritization of failure modes in the context of electrical power systems.

Dynamic phase modulation is vital for tunable focusing, beaming, polarization conversion and holography. However, it remains challenging to achieve full 360∘ dynamic phase modulation while maintaining high reflectance or transmittance based on metamaterials or metasurfaces in the terahertz regime. Here we propose a doubly resonant graphene-metal hybrid metasurface to address this challenge. Simulation results show that by varying the graphene Fermi energy, the proposed metasurface with two shifting resonances is capable to provide dynamic phase modulation covering a range of 361∘ while maintaining relatively high reflectance above 20% at 1.05 THz. Based on the phase profile design, dynamically tunable beam steering and focusing are numerically demonstrated. We expect this work will advance the engineering of graphene metasurfaces for the dynamic manipulation of terahertz waves.

Conducting quantitative research involving adolescents demands a thoughtful approach to the question of supervision, given that each option comes with its distinct set of implications. This study reviews these implications and empirically tests whether differences in data quality can be found among three modes of standardized survey research with medium sized groups of adolescents (12-17 years). Data basis is a quasi-experimental survey study testing different forms of digital, hybrid or in-person supervision, that took place in 2021 in secondary schools in Germany (N=923). Aim of this study is testing how aspects of data quality – item-nonresponse, interview duration, drop-out-rate and response patterns – differ between these forms of supervision. Results could help researchers surveying young people to decide (1) whether they allow confidants or other adults to be present during interviews, (2) if they can rely on teachers alone when surveying classrooms and (3) if it is cost-efficient to send out external supervisors for classroom sessions. While dropout-rates do not differ, item non-response, interview duration, and response patterns differ significantly, students supervised at home by external interviewers answered more questions, took more time to answer and are less likely to give potentially meaningless answers in grid questions. The implications drawn from the findings question the common approach to solely rely on teachers for survey administration without the support of external supervisors or adequate training. Recruiting respondents via schools and surveying them online in their homes during school hours shows to be a robust method with regard to the analyzed indicators.

A closed form solution for the common and differential modal currents induced on a pair of infinitely long parallel conductors by a voltage source was derived. For lossy conductors the current consists of a continuous spectrum of radiation modes and (for the common mode) a modified low loss Sommerfeld-Goubau mode and (for the differential mode) a quasi-TEM mode. This model is used to investigate the influence of a parallel conductor on microwave power line communication systems. For typical parameters, it is shown that the performance of these systems can be enhanced.

In this paper, bikeshare data in Chicago on weather-friendly days in 2019 and 2020 were analyzed to investigate the variation in bikeshare travel before and during the pandemic. Our results show that bikeshare trips during the pandemic were much longer than prior to the pandemic. The increased rate of bikeshare usage was unbalanced spatially and varied significantly for different user types. Specifically, bikeshare was used significantly more by casual users than by subscribers, and the increase occurred much more in the outskirts of the city. The increase in bikeshare travel was associated with a reduction in travel by ride-hailing and public transit, especially in the urban periphery. The correlation of bikeshare use with the bus system was much less significant than with the rail system. Bike lanes/facilities had a mixed effect on bikeshare travel. Weekend bike trips increased in areas where there was no bike lane. Weekday trips, on the contrary, increased in the vicinity of bike greenways.

Oil spills may have devastating effects on marine ecosystems, public health, the economy, and coastal communities. Therefore, scientific literature contains various up-to-date, advanced oil spill predictive models, capable to simulate the trajectory and evolution of an oil slick generated by the accidental release from ships, hydrocarbons production, or other activities. To predict in near real time oil spill transport and fate with increased reliability these models are usually coupled operationally to synoptic meteorological, hydrodynamic, and wave models. The present study reviews the available different met-ocean forcings that have been used in oil spill modeling, simulating hypothetical or real oil spill scenarios, worldwide. Nine state-of-the-art oil spill models are critically examined in terms of the met-ocean data used as forcing inputs in the simulation of twenty-four case studies. Results illustrate that most oil spill models are coupled to different resolution, forecasting meteorological and hydrodynamic models, posing, however, limited consideration in the forecasted wave field (expressed as the significant wave height, the wave period and the Stokes drift) that may affect oil transport, especially at the coastal areas. Moreover, the majority of oil spill models lacks any linkage to the background biogeochemical conditions, hence, limited consideration is given in processes like oil biodegradation, photo-oxidation and sedimentation. Future advancements in oil spill modeling should be directed towards the full operational coupling with high-resolution atmospheric, hydrodynamic, wave, and biogeochemical models, improving our understanding in the relative impact of each physical and oil weathering process.

Wireless Sensor Network (WSN) and the sensing devices are considered part of the core components of the Internet of Things (IoT). Hence, the modeling of IoT-WSNs is fundamental to having a better understanding, management, and deployment of this kind of technology. A fundamental issue in WSN is energy consumption due to the inherent limitations of this resource in the sensor devices. On the other hand, several issues arise in heterogeneous scenarios due to the coexistence of different sensor devices. Therefore, the modeling process becomes challenging and must consider the different transmission and operation cycles and modes that the transmission protocol implements to assure successful functioning in terms of transmission, synchronization, and energy savings. A duty-cycled MAC WSN protocol (PSA-MAC) has been modeled based on a pair of two-dimensional Discrete-Time Markov Chain (2D-DTMC), whose solution in terms of stationary probability distribution is used by expressions that have been derived to evaluate the energy consumption of sensor devices that could be used for WSN-based IoT applications. Analytical results of average energy consumption are obtained, where the synchronization, data, and sleep periods of a full transmission cycle are considered in a heterogeneous scenario with different node classes and priority assignments. Also, the normal and awake operation cycles are considered to assure synchronization and energy savings. Moreover, the transmission schemes of SPT (transmission of single packets) and APT (transmission of packets in aggregation) are also considered in the model. These results are validated through discrete event-based simulations, and the obtained results are accurate.

The manuscript presents a unified methodology for the engineering design of resonant inverters used for power sources to power various technologies based on induction heating. The methodology is compiled using the generalized consideration of electromagnetic processes in a series RLC circuit and the quasi-boundary method for the analysis of resonant inverters with and without reverse diodes operating in soft and hard commutation modes. On this basis, the transmission functions of the inverters are derived, and the matching between the parameters of the inverter and the load through complicated output circuits is also considered. The basic ratios for determining the circuit elements and their current and voltage loading are presented. The methodologies are verified using several computational examples, simulations and measurements from induction heating devices. The simplified design approach presented is useful for its application in power electronics training and also in the design of various devices using the principle of induction heating. Another important result is the achievement of formalization and algorithmization of the design process, which is a consequence of the application of a unified approach both in the analysis and in the design of a whole class of power electronic devices.

Oscillations in global modes of variability (MoV) form global teleconnections that affect regional climate variability and modify the potential for severe and damaging weather conditions. Understanding the link between certain MoVs and regional climate can improve the ability to more accurately predict environmental conditions that impact human life and health. In this study, we explore the connection between different MoVs, including the Arctic Oscillation (AO), Eurasian teleconnection, Indian Ocean Dipole (IOD), North Atlantic Oscillation (NAO), and El Niño Southern Oscillation (Nino34), with winter and summer climate in the High Mountain Asia (HMA) region, including geopotential height at 250 hPa (z250), 2-m air temperature (T2M), total precipitation (PRECTOT), and fractional snow cover area (fSCA). Relationships are explored for the same monthly period between the MoVs and the climate variables, but also using a lagged correlation analysis to investigate whether any relationship exists at different time lags. We find that T2M has a negative correlation with the Eurasian teleconnection in the Inner Tibetan Plateau and Central China in both winter and summer and a positive correlation in Western China in summer. PRECTOT has a positive correlation with all MoV in most regions in winter, especially with the IOD, and a negative correlation in summer, especially with the Eurasian teleconnection. Snow cover in winter is positively correlated with most indices throughout many regions in HMA, likely due to wintertime precipitation also being positively correlated with most indices. Generally, the AO and NAO show similar correlation patterns with all climate variables, especially in the winter, possibly due to their oscillations being so similar. Furthermore, the AO and NAO are shown to be less significant in explaining the variation in HMA climate compared to other MoVs such as the Eurasian teleconnection. Overall, our results pinpoint different time-windows and specific regions within HMA that exhibit high correlation between climate and MoVs, which might offer additional predictability of the MoVs as well as of climate and weather patterns in HMA and throughout the globe.

Effective control of domain walls or magnetic textures in antiferromagnets promises to enable robust, fast, and non-volatile memories. The lack of net magnetic moment in antiferromagnets implies the need for creative ways to achieve such a manipulation. Here, we investigate changes in magnetic force microscopy (MFM) imaging and in magnon-related mode in Raman spectroscopy of virgin NiO films under a microwave pump. After the MFM and Raman studies, a combined action of broadband microwave (0.01-20 GHz, power scanned from −20 to 5 dBm) and magnetic field (up to 3 kOe) were applied to virgin epitaxial (111) NiO and (100) NiO films grown on (0001) Al2O3 and (100) MgO substrates, following which the MFM and Raman studies were repeated. We observed a suppression of the magnon-related Raman mode subsequent to the microwave exposure. Based on MFM imaging, this effect appears to be caused by the suppression of large antiferromagnetic domain walls due to the possible excitation of antiferromagnetic spin oscillations localized within the antiferromagnetic domain walls.

Arid- and semi-arid Central Asia is particularly sensitive to climate change. The changes in extreme precipitation in Central Asia stemming from climate warming are the subject of intense debate within the scientific community. This study employed a Morlet wavelet analysis to examine the annual occurrence number of extreme precipitation in Central Asia from May to September during the period of 1951–2005. Their modulating planetary-scale climate modes were identified by using a linear regression analysis. Two major scales of the temporal variability were derived: 2–3.9 yr and 4–6 yr. The dominant variability was 2–3.9-yr scale and was associated with the negative phase of the Polar/Eurasia (POL) pattern. The 4–6-yr scale provided a secondary contribution and was closely linked to the negative phase of the North Atlantic Oscillation (NAO). These planetary climate modes acted as precursors of extreme precipitation over Central Asia. The negative phase of POL directly contributed to a negative height anomaly over Central Asia, which was intimately related to extreme precipitation. In contrast, the negative NAO phase possibly manifested as a Rossby wave source, which was subsequently exported to Central Asia through a negative–positive–negative Rossby wave train.

This article discuss the effects of heat treatment and lubrication modes on the machinability of an A356 alloy (Al-Si-Mg); the alloy is studied as-received, with solution heat-treated alloy (SHT) as well as with an alloy that is solution heat-treated and then aged at 155, 180 and 220 °C. In the course of machinability evaluation, several criteria including cutting force, surface roughness, tool wears and burr analysis (chip) were studied. The results and analysis in this work indicated that the selected machinability criteria are important and necessary to effectively evaluate the machinability of A356 alloys. The machinability of both materials and tools were estimated in terms of cutting force, chip thickness ratio and burr formation, flank wear and roughness. The effects of different cutting parameters (cutting speed and feed rate) and lubrication modes (dry, mist and wet) on the machinability of the A356 cast alloy were also examined. The influence of heat treatments on the burr formation and surface quality was clearly revealed by the experimental results. Experimental work revealed that cutting forces were influenced significantly by aging and cutting speed. However, the different aging at 155, 180, and 220 °C and the cutting speed significantly affected the machinability of the A356 cast alloy. The results obtained show that a better drilling performance in terms of surface quality occurs at a high feed rate, with dry drilling and artificial aging at T6.

Reliability assessment in traditional power distribution systems has played a key role in power system planning, design, and operation. Recently, new information and communication technologies have been introduced in power systems automation and asset management, making the distribution network even more complex. In order to achieve efficient energy management, the distribution grid has to adopt a new configuration and operational conditions that are changing the paradigm of the actual electrical system. Therefore, the emergence of the cyber-physical systems concept to face future energetic needs requires alternative approaches for evaluating the reliability of modern distribution systems, especially in the smart grids environment. In this paper, a reliability approach that makes use of failure modes of power and cyber network main components is proposed to evaluate risk analysis in smart electrical distribution systems. We introduce the application of Failure Modes and Effects Analysis (FMEA) method in future smart grid systems in order to establish the impact of different failure modes on their performance. A smart grid test system is defined and failure modes and their effects for both power and the cyber components are presented. Preventive maintenance tasks are proposed and systematized to minimize the impact of high-risk failures and increase reliability.

In the mean- field approximation, the well-known effect of the critical quantum collapse in a 3D gas of particles pulled to the center by potential U(r) = -U_0/(2r^2) is suppressed by repulsive interparticle interactions, which create the otherwise non-existing s-wave ground state. Here, we address excited bound states carrying the angular momentum, with the orbital and magnetic quantum numbers, l and m. They exist above a threshold value of the potential's strength, U_0 > l(l+1). The sectoral, tesseral, and zonal modes, which correspond to m = l, 0 < m < l, and m = 0, respectively, are found in an approximate analytical form for relatively small values of U_0 - l(l + 1). Explicit results are produced for the p- and d-wave states, with l = 1 and 2, respectively. In the general form, the bound states are obtained numerically, confirming the accuracy of the analytical approximation.

In this paper, we consider the behavior of the local energy flow velocity of the fundamental air – core mode at the core – cladding boundary in two types of hollow – core fibers: hollow – core fibers with a negative curvature of the core boundary and single – capillary fibers with similar geometrical parameters. It is demonstrated that the behavior of both axial and radial components of the local energy velocity of the fundamental air – core mode is completely different for these two types of hollow – core fibers. The negative curvature of the core boundary leads to an alternating behavior of the radial projection of the local energy velocity and a decrease by two orders of magnitude compared to the values of this projection for a single capillary. In our opinion, this behavior of the local energy velocity of the fundamental air – core mode is caused by a periodic set of Poynting vector vortices that appear in the cladding capillary walls.

We show that perturbations of a scalar field in the background of the black hole obtained with the Starobinsky-Bel-Robinson Gravity is unstable unless the dimensionless coupling $\beta$ describing the compactification of M-theory is small enough. In the sector of stability quasinormal spectrum show peculiar behavior both in the frequency and time domains: the ringing consists of two stages where two different modes dominate. The WKB method does not reproduce part of the spectrum including the fundamental mode, which is responsible for the first stage of the ringing. Consequently, the correspondence between the eikonal quasinormal modes and null geodesics allows to reproduce only part of the eikonal spectrum. The frequencies are obtained with the help of three methods (Frobenius, WKB and time-domain integration) with excellent agreement among them.

Chemical safety is related to public health, safety and environmental concerns, and the dangerous chemicals safety problem is becoming the one that people commonly pay attention to. Strengthening chemical safety supervision not only involves safe production, but also is an important link to maintain social safety. Most related studies focus on chemical safety under normal regulation, this paper addresses the perspective of ‘special rectification’ and ‘normal regulation’, and establishes an evolutionary game model between chemical enterprises and government supervision departments under different supervision modes. Based on the evolutionary game theory, this paper studies the evolution process of the two game players' strategy choices, and compares and analyzes the evolution, stability and equilibrium between the chemical safety and the behavior strategies of government regulatory departments. The model is effectively analyzed based on numerical simulation, and the results show that: Under the ‘special rectification’ mode, the strategic choice of chemical enterprises engaging in safety without investment depends on the difference between the benefits and costs of safety without investment; In the ‘normal regulation’ mode, the choice of its safety non-investment strategy depends on the difference between the cost of engaging in safety investment and the cost of safety non-investment; Increasing the government's punishment will encourage chemical enterprises to take safety investment behavior under the two supervision modes. Increasing the punishment has a significant impact on the safety investment behavior of chemical enterprises under the ‘normal regulation’ mode, but it has no significant impact on the behavior of chemical enterprises under the ‘special rectification’ mode. At the same time, increasing the punishment will inhibit the strict supervision behavior of the government. The research conclusion provides important decision support for government departments to effectively supervise the safety production of chemical enterprises.

In this study, the motion characteristics of soft alginate microrobots were investigated with wireless magnetic fields in complex fluidic environments. Our aim is to explore the various motion modes that arise as a result of shear forces in viscoelastic fluids. Polyacrylamide (PAA), a water-soluble polymer, was characterized to produce a dynamic environment with a non-Newtonian fluid. The robots were fabricated by an extrusion-based microcentrifugal droplet method. We successfully demonstrated the feasibility of both wiggling and tumbling motions using snowman-shaped microbots. It is found that wiggling motion is primarily influenced by the interaction between the viscoelastic fluid environment and the non-uniform magnetization of the microbots. Additionally, it is discovered that modifying the viscoelasticity properties of the fluid can affect the motion behavior of the microbots. Furthermore, we observed that swarms of microbots exhibit non-uniform behavior within complex environments. Our velocity analysis has provided valuable insights into the relationship between applied magnetic fields and motion characteristics, enabling a more realistic understanding of surface locomotion in the context of targeted drug delivery.

The logarithmic correction to Bekenshtein$-$Hawking entropy in the framework of 4D Einstein - Gauss - Bonnet gravity coupled with nonlinear electrodynamics is obtained. We explore the black hole solution with the spherically symmetric metric. The logarithmic term in the entropy has a structure similar to the entropy correction in the semi-classical Einstein equations which mimics the quantum correction to the area low. The energy emission rate of black holes and energy conditions are studied. The quasinormal modes of a test scalar field are investigated. The gravitational lensing of light around BHs was studied. We calculated the deflection angle for some model parameters.

The antimicrobial quantitative structure–activity relationship of plant flavonoids against Gram-positive bacteria was established in our previous works, and the cell membrane was confirmed as a major site of action. To investigate whether plant flavonoids have similar antibacterial effects and mechanisms against both Gram-negative and Gram-positive bacteria, here, the minimum inhibitory concentrations (MICs) of 37 plant flavonoids against Escherichia coli were determined using the microdilution broth method, and then the correlation between their lipophilic parameter ACD/LogP or LogD_7.40 value and their MIC was analyzed. Simultaneously, the correlation between the ACD/LogP or LogD_7.40 value and the MIC of 46 plant flavonoids reported in literature against E. coli was also analyzed. Both sets of results showed that there is a significant correlation between the LogP value and the MIC of plant flavonoids against Gram-negative bacteria. However, it is difficult to effectively predict the MIC of plant flavonoids against Gram-negative bacteria from their lipophilic parameters. By comparing two regression curves derived from plant flavonoids against Gram-negative and Gram-positive bacteria, it was further discovered that the antibacterial activities of most plant flavonoids against Gram-negative bacteria are stronger than those against Gram-positive bacteria when their LogP values are less than about 3.0, but the opposite is true when their LogP values are more than about 3.6. Moreover, this comparison also suggests that unlike mainly acting on the cell membrane of Gram-positive bacteria, plant flavonoids have multiple mechanisms against Gram-negative species, while the cell membrane is also an important action site among them. Combined with the correlation analyses between the enzyme inhibitory activity and the LogP value of the reported flavonoids, it was further suggested that DNA gyrase is another important target of plant flavonoids against Gram-negative bacteria.

Existing reinforced concrete buildings with seismically-deficient column details affect the overall behavior depending on the failure type of column. The purpose of this study is to develop and validate a machine learning-based prediction model for the column failure modes (shear, flexure-shear and flexure failure modes). For this purpose, artificial neural network (ANN), K-nearest neighbor (KNN), decision tree (DT), and random forest (RF) models were used considering previously-collected experimental data. Using four machine learning methodologies, we developed a classification learning model that can predict the column failure modes in terms of the input variables using concrete compressive strength, steel yield strength, axial load ratio, height-to-dept aspect ratio, longitudinal reinforcement ratio, and transverse reinforcement ratio. The performance of each machine learning model was compared and verified by calculating accuracy, precision, recall, F1-Score, and ROC. Based on the performance measurements of the classification model, the RF model represents the highest average value of the classification model performance measurements among the considered learning methods, and it can conservatively predict the shear failure mode. Thus, the RF model can rapidly predict the column failure modes with the simple column details. Additionally, it was demonstrated that the predicted failure modes from the selected model were exactly same as the failure mode determined from a code-defined equation (traditional method)

In this paper, a dual-band WiFi antenna and its Multiple Input Multiple Output (MIMO) system application is designed, fabricated, and measured based on the Chinese characters “Men” and “Wei”. The antenna uses a 40×40×1.6 mm3 Fr4 substrate to analyze the combinatorial structure of Chinese characters using the theory of characteristic modes (TCM), to optimize the antenna dimensions by analyzing the mode current distribution, and to broaden the antenna bandwidth by etching rectangular slots on the ground. The measured and simulated results show that the four-element MIMO antenna covers 5.68-8.01 GHz, the isolation between the antennas is higher than 20 dB in the working band, the Envelope Correlation Coefficient (ECC) and the channel capacity losses (CCLs)of the simulation is lower than 0.001 and 0.18 bits/s/HZ, respectively. The efficiency of the antenna is higher than 90%, and it can be used for WiFi communication band (5.8 GHz and 6 GHz).

Variable-DOF (or kinematotropic) mechanisms are a class of reconfigurable mechanisms. The number of variable-DOF multi-loop planar mechanisms proposed so far is very limited. This paper proposes a novel 8-link variable-DOF planar mechanism with five motion modes. Firstly, a description of the 8-link variable-DOF planar mechanism is presented. Reconfiguration analysis of the 8-link mechanism is then carried out using an elimination and algebraic geometry hybrid approach. The analysis shows that the 8-link mechanism has one 2-DOF motion mode and four 1-DOF motion modes and can switch among three motion modes at four transition configurations and between two motion modes at the remaining four transition configurations. Geometric characteristics of the mechanism in different motion modes are also revealed. Unlike the variable-DOF planar mechanisms found in literature, the proposed 8-link mechanism has two inactive joints in one of its 1-DOF motion modes, and both 4R kinematic sub-chains of the mechanism must appear as parallelograms in a pair or anti-parallelograms in a pair in the same motion mode. As a by-product, a method for factoring trigonometric functions in two angles is proposed.

The wind industry is looking for ways to accurately predict the reliability and availability of newly installed wind turbines. Failure modes, effects and criticality analysis (FMECA) is a technique utilized for determining the critical subsystems of wind turbines. There are several studies which applied FMECA for wind turbines in the literature, but no studies so far have considered different weather conditions or climatic regions. Furthermore, various design types of wind turbines have been analyzed applying FMECA but no study so far has applied FMECA to compare the reliability of geared and direct-drive wind turbines. We propose to fill these gaps by using Koppen-Geiger climatic regions and two different turbine models of direct-drive and geared-drive concepts. A case study is applied on German wind farms utilizing the WMEP database which contains wind turbine failure data from 1989 to 2008. This proposed methodology increases the accuracy of reliability and availability predictions and compares different wind turbine design types and eliminates underestimation of impacts of different weather conditions.

Oxidative stress is defined as an imbalance between the production of free radicals and reactive oxygen species (ROS) and the ability of the body to neutralize them by antioxidant defense systems. Cells produce ROS as a control of physiological processes, but increasing ROS becomes pathological leading to non-specific and irreversible damage to biological molecules, such as DNA, lipid, and protein. Endogenous ROS are mainly produced by mitochondria during both physiological and pathological conditions, and enzymes, such as nicotinamide adenine dinucleotide phosphate oxidase (NOX), xanthine oxidase (XO), lipoxygenase (LOX), myeloperoxidase (MPO) and monoamine oxidase (MAO). To neutralize ROS, the body employs enzymatic and non-enzymatic defense systems. The dietary intake of bioactive phenols, such as quercetin (Que), is a non-enzymatic system that can quench ROS and protect from pro-oxidative damage. In this review, we evaluate the ability of Que to target endogenous oxidant enzymes involved in ROS production and explore the mechanisms of action underlying its antioxidant properties. Que not only acts as a free radical scavenger by donating electrons through the negative charges in its phenolic and ketone groups, but it can effectively inhibit the activity of several endogenous oxidative enzymes, binding them with high affinity and specificity. Among all targets, Que showed the best results in molecular docking simulations with XO, followed by MAO-A, 5-LOX, NOX, and MPO. Taken together, these findings highlight the potential of Que as a natural antioxidant therapy for oxidative stress-related diseases.

We investigate on the plasmons of monolayer MoS₂ in the presence of spin-orbit interactions (SOIs) under the random phase approximation. The theoretical study shows that two new and novel plasmonic modes can be achieved via inter spin sub-band transitions around the Fermi level duo to the SOIs. The plasmon modes are optic-like, which are very different from the plasmon modes reported recently in monolayer MoS₂, and the other two-dimensional systems. The frequency of such plasmons increases with the increasing of the electron density or the spin polarizability, and decreases with the increasing of the wave vectors q. Our results exhibit some interesting features which can be utilized to the plasmonic and terahertz devices based on monolayer MoS₂.

Fault line detection timely and accurately when single-phase-to-earth fault occurs in resonant grounding system is still a focus of research. This paper presents a new approach for fault detection based on data fusion and it has non-artificial setting. Firstly, the fault criterion for interphase difference energy ratio and time-frequency correlation coefficient of each line is proposed. Subsequently, the paper establish a coordinate system with the interphase difference energy ratio as X axis and the time-frequency correlation coefficient as Y axis, and it uses the Euclidean distance algorithm to get the characteristic distance of each line by fusing two-dimensional information. Finally, comparing the sound distance and the fault distance of each line to discriminate the fault line. Electromagnetic Transients Program (EMTP) simulation results and adaptability analysis have confirmed the effectiveness and reliability of the proposed scheme.

In this paper, a novel voltage control strategy of stand-alone operation brushless doubly fed induction generator for variable speed constant frequency wind energy conversion systems was presented and discussed particularly. Based on the model of the generator power system, the proposed direct flux control strategy employs a nonlinear reduced-order generalized integrator based resonant sliding-mode control scheme to directly calculate and regulated the output value of converter which control winding stator required so as to eliminate the instantaneous errors of power winding stator flux, and no involving any synchronous rotating coordinate transformations. The stability, robustness and convergence capability of the proposed control strategy were described and analyzed. Owing to no extra current control loops involved, therefore simplifying the system configuration design and enhancing the transient performance. Constant converter switching frequency was achieved by using space vector pulse width modulation, which reduce the harmonic of generator terminal voltage. In addition, experimental results prove the feasibility and validity of the proposed scheme, and excellent steady and dynamic state performance is achieved.

This paper attempts at applying adaptive network-based fuzzy inference system (ANFIS) for analysis of the resonant frequency of a microstrip rectangular patch antenna with two equal size slots which are placed on the patch vertically. The resonant frequency is calculated as the position of slots is shifted to the right and left sides on the patch. As a result , the antenna resonates at more than one frequency . Commonly, machine algorithms based on artificial neural networks are employed to recognize the whole resonant frequencies. However ,they fail to estimate the resonant frequencies correctly as in some cases variations are not very sensible and the resonant frequencies overlap each other . It can be concluded that artificial neural networks could be replaced in such designs by the adaptive network-based fuzzy Inference system due to its high approximation capability and much faster convergence rate.

Background: Recent researches have investigated the biological importance of RNA N1-methyladenosine (m1A) modifications in oncogenesis and progression of head and neck squamous cell carcinoma (HNSCC). However, whether m1A modifications also have latent effect in tumor microenvironment (TME) generation and immune regulation in HNSCC is unknown. Methods: We evaluated the m1A modification patterns and related to these modification patterns with TME cell infiltration features in 1041 HNSCC samples by bioinformatics approach. Results: The m1A score is an independent prognostic indicator. HNSCC patients with low m1A score group with poor overall survival (OS) was mainly characterized by stroma activation, lack of sufficient immune infiltration, and exhibited an immune- desert TME phenotype. Low m1A scores were also correlated with increased tumor mutation burden (TMB), and HNSCC patients with high TMB and low m1A scores had the worst OS. In addition, anti-CTLA-4 combined with anti-PD1 treatment was more effective in the high m1A score subgroup than in the low m1A score subgroup. Conclusions: This study revealed that m1A modifications play a non-negligible role in developing the TME versatility and complexity of HNSCC. Assessing m1A modification patterns in HNSCC helps improve our comprehension of its TME infiltration profile and guides more effective immunotherapeutic approaches.

In forests, the microbial populations living in the soil can directly affect the carbon decomposed by the surface plants, and promote carbon storage and stability. In this study, 3 plots of 25.82 m×25.82 m were set up in 5 stand types, respectively. Soil samples were collected from 0~20 cm, 20~40 cm and 40~60 cm layers. Soil microbial composition, organic carbon component, pH, water content, bulk density, nitrogen, phosphorus, potassium and other physicochemical indexes and correlations were determined, and the correlations between soil carbon components and soil microbial functional modules in different mixed modes were analyzed. The results showed that: (1) The SOC of the same soil layer varied significantly, which also showed significant differences on the composition of soil bacteria and fungal microbial communities. Moreover, the bacterial community was more sensitive to the vegetation change environment, and the fungal community structure was more resistant to the influence of soil environment changes. (2) Fun_mod 1,6 and Bac_mod 7 were the microbial functional modules that played a decisive role in the process of soil carbon pool change, and the diversity and composition of bacterial community had more positive effects on soil organic carbon than that of fungal community. (3) Linear fitting and RDA results showed that POC in soil had the strongest correlation with SOC content, indicating that soil microorganisms affected the storage and stability of soil carbon mainly by regulating the conversion of surface plants (carbon sources) into POC. The soil environment of different mixed modes has different effects on soil carbon accumulation. Soil microorganisms affect soil carbon storage and stability mainly by regulating the conversion of surface plants (carbon sources) into POC forms.

The results of electron-beam processing of Mn-Zn ferrite samples using pulsed and continuous electron beams in the forevacuum pressure range (10 Pa) are presented. We find that continuous electron-beam processing leads to surface structuring of the ferrite, changes in elemental composition on the surface, and electrical property modification. The degree of ferrite parameter changes exhibits a threshold behavior. For surface processing temperatures below 900 °C, changes are barely noticeable, while for temperatures over 1100 °C the surface resistance decreases by more than an order of magnitude. Electron-beam processing with millisecond pulse duration and pulse energy density exceeding 15 J/cm² results in the formation of low zinc content melt islands, while the remaining surface area (outside the islands) elemental content and ferrite properties remain largely unchanged. The thickness of the modified layer depends on the processing mode and can be controlled over the range 0.1–0.5 mm. Because of its low resistance, the modified layer can be utilized to enhance the RF-absorbing properties of the ferrite.

The influence of linear and nonlinear modes of ADC driver on the operational amplifier (Op-Amp), which has different values of maximum output voltage slew rate, on the effective number of bits of ADC is considered. It is shown that the effective number of bits of ADC when op-amps on bipolar transistors with input signal amplitudes exceeding 50-100 mV is determined by the nonlinear modes of its input differential stage.

Previous research on the relative benefits of Augmentative and Alternative Communication Systems (AACs) has indicated controversial results regarding the effectiveness, the ease of use, and the preference for the different systems. The study aims to observe the comparative effectiveness of two different Augmentative and Alternative Communication (AAC) tools, the Picture Exchange Communication System (PECS) and a speech-generating device (SGD), as communication aids for children with autism. Three children with severe autism and minimally verbally or with no functional language participated. The results showed an increase of communicative behavior with both AAC intervention strategies and a speed acquisition time slightly shorter for the SGD training. Two of the three participants showed a preference for the use of the SGD. Reduction in problem behaviors and improvement in vocal production was observed for one of the participants. Results suggest that PECS and SGD are similarly appropriate for the development of initial request skills and that they can encourage vocal production in students with specific prerequisites.

Considering the aging society and budget constraints, a strategy for reforming public transportation welfare policies is essential for sustainability. Among the various transportation welfare policies, fare discount policies are provided to specific age groups, and most countries offer benefits to several public transportation. South Korea provides a fare-free policy limited to subways, and the need for policy modification is emerging due to sustainability problems caused by an aging society. Hence, the scope of the policy should be expanded to all travel modes, but the discount rate should be reduced, or the target group should be reduced in consideration of the budget. This study proposes a travel mode to focus on by city through the preference of the elderly. The latent class model is employed to classfy stated preference data collected from the survey. The estimation results show a significant preference heterogeneity depending on the level of subway supply by region, and a policy focused on subways would be more reasonable in cities with sufficient subway infrastructure. Hence, regarding sustainability, it may be more appropriate to focus on specific means than to provide the same discount policy for all public transport.

The vibration propagates in a media such as a shaft in the form of elastic waves. The propagation characteristics of the waves are affected by the geometry of the media, the material properties as well as the cracks. The study to elastic waves propagating in a shaft with transverse cracks can help to detect them. The transverse crack possesses different crack modes due to different external loads. The influence of the crack mode, the location and the depth to the propagation characteristics is investigated in this paper. Firstly, the local flexibility coefficients with three different modes are deduced. And then, the transfer matrix of the elastic wave can be obtained. Finally, the influence of the crack mode, the location and the depth of the transverse crack as well as the rotating speed to the propagation characteristics is then studied, both in a numerical and an experimental way. It’s found that mode III is the most suitable mode in this paper, the location of the crack will make the stopbands fluctuating, the depth mainly affects the bandwidth of the stopbands, and the increase of the rotating speed will shift up the stopbands without changing their bandwidths.

In two previous papers, we calculated the dielectrophoresis (DEP) force and corresponding trajectories of high- and low-conductance 200-µm 2D spheres in a square 1x1mm chamber with plane-versus-pointed, plane-versus-plane and pointed-versus-pointed electrode configurations by applying the law of maximum entropy production (LMEP) to the system. Here, we complete these considerations for configurations with four-pointed electrodes centered on the chamber edges. The four electrodes were operated in either object-shift mode (two adjacent electrodes opposite the other two adjacent electrodes), DEP mode (one electrode versus the other three electrodes), or field-cage mode (two electrodes on opposite edges versus the two electrodes on the other two opposite edges). As in previous work, we have assumed DC properties for the object and the external media for simplicity. Nevertheless, every possible polarization ratio of the two media can be modeled this way. The trajectories of the spherical centers and the corresponding DEP forces were calculated from the gradients of the system’s total energy dissipation, described by numerically-derived conductance fields. In each of the three drive modes, very high attractive and repulsive forces were found in front of pointed electrodes for the high and low-conductance spheres, respectively. The conductance fields predict bifurcation points, watersheds, and trajectories with multiple endpoints. The high and low-conductance spheres usually follow similar trajectories, albeit with reversed orientations. In DEP drive mode, the four-point electrode chamber provides a similar area for DEP measurements as the classical plane-versus-pointed electrode chamber.

The three-dimensional structure of Gulf of Mexico’s warm-core rings, detaching from the Loop Current, is investigated using satellite altimetry and a large set of ARGO float profiles. Reconstruction of the Loop Current rings (LCRs) vertical structure from sea surface height observations is made possible by the use of the gravest empirical modes method (GEM). The GEMs are transfer functions that associate a value of temperature and salinity for each variable pair {dynamic height;pressure}, and are computed by estimating an empirical relationship between dynamic height and the vertical thermohaline structure of the ocean. Between 1993 and 2021, 40 LCRs were detected in the altimetry and their three-dimensional thermohaline structure was reconstructed, as well as a number of dynamically relevant variables (geostrophic and cyclogeostrophic velocity, relative vorticity, potential vorticity, available potential energy and kinetic energy density etc.). The structure of a typical LCR was computed by fitting an analytical stream function to the LCRs dynamic height signature and reconstructing its vertical structure with the GEM. The total heat and salt contents and energy of each LCR were computed and their cumulative effect on the Gulf of Mexico’s heat, salt and energy balance is discussed. We show that LCRs have a dramatic impact on these balances and estimate that residual surface heat fluxes of -13 Wm−2 are necessary to compensate their heat input, while the fresh water outflow of the Mississippi river approximately compensates for their salt excess input. An average energy dissipation of O[10−10−10−9] Wkg−1 would be necessary to balance their energy input.

A series of Cu(II)-thiocyanato complexes derived from sterically hindered N-donors diamines were synthesized and characterized: catena-[Cu(Me₃en)(μ-NCS)(NCS)] (1), catena-[Cu(NEt₂Meen)(μ-NCS)(NCS)] (2), catena-[Cu(N,N,2,2-Me₄pn)(μ-NCS)(NCS)] (3), the dimeric: [Cu₂(N,N′-isp₂en)₂(μ-NCS)₂(NCS)₂] (4) and the monomeric complex [Cu(N,N′-t-Bu₂en)(NCS)₂] (5), where Me₃en = N,N,N′-Trimethylethylenediamine, NEt₂Meen = N,N-diethyl-N′-methylethylenediamine, N,N,2,2-Me₄pn = N,N,2,2-tetramethylpropylenediamine, N,N′-isp₂en = N,N′-diisopropylethylenediamine and N,N′-t-Bu₂en = N,N′-di(tert-butyl)ethylenediamine. The complexes were characterized by elemental microanalyse, IR and UV-Vis spectroscopy and single crystal X-ray crystallography. Density Functional Theory was used to evaluate the role of steric effects in compounds 4 and 5 and how this may affect the adaption of a specific geometry, NCS-bonding mode and the dimensionality of the resulting complex.

With the realization of the Grand Canal's full water supply and the strong pursuit of green and low-carbon transportation in contemporary society, the value of the Grand Canal's water transport has been further affirmed, and its coordinated development with other transportation modes has become inevitable and important. This paper analyzes and combs through the characteristics, development status and existing problems of Grand Canal water transport and other transport modes in depth, and takes Jiangsu as an example. A collaboration model of Grand Canal water transport and other transport modes was built and their collaboration degree has been calculated. It is believed that the coordinated development of Grand Canal water transport and other transport modes can be greatly promoted via four aspects: optimizing the construction and governance of Grand Canal water transport, building an integrated management platform of transport modes, improving the integrated transport network structure, and promoting the deep integration of integrated shipping and tourism.

The comparative phylogeography of marine species with contrasting dispersal potential across the southern Caribbean Sea was evaluated by the presence of two putative barriers: the Magdale-na River plume (MRP) and the combination of the absence of a rocky bottom and permanent upwelling in the La Guajira Peninsula (ARB+PUG). Three species of rocky shallow bottoms were selected with different dispersal potentials: Acanthemblemaria rivasi (PLD < 22 days), Cittarium pica (PLD < 6 days), and Nerita tessellata (PLD > 60 days). We generated a set of SNPs for the three species using the ddRad-seq technique. Samples of each species were collected in five locations from Capurganá to La Guajira. For the first time, evidence of a phylogeographic break caused by MRP is provided, mainly for A. rivasi (AMOVA: ФCT = 0.420). The ARB+PUG barrier causes an-other break for A. rivasi (ФCT = 0.406) and C. pica (ФCT = 0.224). Three populations (K = 3) were identified for A. rivasi and C. pica, while N. tessellata presented one population (K = 1). The Mantel correlogram indicated that A. rivasi and C. pica fit the hierarchical population model, and only the A. rivasi and C. pica comparisons showed phylogeographic congruence. Our results demon-strate how the biological traits of these three species and the biogeographic barriers have influ-enced their phylogeographic structure.

In this research, Assume a neutrosophic SuperHyperGraph. Then a ``Failed SuperHyperStable $\mathcal{I}(NSHG)$ for a SuperHyperGraph $NSHG:(V,E)$ is the maximum cardinality of a SuperHyperSet $S$ of SuperHyperVertices such that there's a SuperHyperVertex to have a SuperHyperEdge in common; a ``neutrosophic Failed SuperHyperStable'' $\mathcal{I}_n(NSHG)$ for a neutrosophic SuperHyperGraph $NSHG:(V,E)$ is the maximum neutrosophic cardinality of a neutrosophic SuperHyperSet $S$ of neutrosophic SuperHyperVertices such that there's a neutrosophic SuperHyperVertex to have a neutrosophic SuperHyperEdge in common. Assume a SuperHyperGraph. Then an ``$\delta-$Failed SuperHyperStable'' is a \underline{maximal} Failed SuperHyperStable of SuperHyperVertices with \underline{maximum} cardinality such that either of the following expressions hold for the (neutrosophic) cardinalities of SuperHyperNeighbors of $s\in S:$ $~|S\cap N(s)| > |S\cap (V\setminus N(s))|+\delta,~|S\cap N(s)| < |S\cap (V\setminus N(s))|+\delta.$ The first Expression, holds if $S$ is an ``$\delta-$SuperHyperOffensive''. And the second Expression, holds if $S$ is an ``$\delta-$SuperHyperDefensive''; a``neutrosophic $\delta-$Failed SuperHyperStable'' is a \underline{maximal} neutrosophic Failed SuperHyperStable of SuperHyperVertices with \underline{maximum} neutrosophic cardinality such that either of the following expressions hold for the neutrosophic cardinalities of SuperHyperNeighbors of $s\in S:$ $~|S\cap N(s)|_{neutrosophic} > |S\cap (V\setminus N(s))|_{neutrosophic}+\delta,~ |S\cap N(s)|_{neutrosophic} < |S\cap (V\setminus N(s))|_{neutrosophic}+\delta.$ The first Expression, holds if $S$ is a ``neutrosophic $\delta-$SuperHyperOffensive''. And the second Expression, holds if $S$ is a ``neutrosophic $\delta-$SuperHyperDefensive''. A basic familiarity with Extreme Failed SuperHyperClique theory, Neutrosophic Failed SuperHyperClique theory, and (Neutrosophic) SuperHyperGraphs theory are proposed.

Noninvasive and portable diagnoses via angle-resolved coherent spectral data are presented. ACTIRS (Angle- resolved coherent tomographic IR spectroscopy) through angle-coherent return spectra from photonic quantum ring laser of whispering gallery modes, which is not photocurrent-converted after the cortical, vascular or muscular diffuse paths, can be a new method for brain/heart studies. Also it will be eligible for frequent do-it-yourself diagnoses of breast cancer before hospital visits. The unique angle-coherent multi-spectra will eventually lead to study ionic or protein contents of cranial, arterial or lactiferous ducts that have been obtained only from uncomfortable biopsy, NMR, CT or mammography. The spectral data can be spatially or temporally improved and correlated for extracting more meaningful diagnostic conclusions

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

To secure logic circuits against the illegal copying the insertion of the so-called key bit inputs using XOR/XNOR gates has been proposed in . The inserted gates modify (lock) the behavior of the original circuit and only the correct choice of the secret key bits guarantees the equivalent behaviour of the locked circuit to the original circuit. To break this kind of security, i.e. to find the secret key bits, there was a SAT solver based attack proposed in . The aim of this work is to experimentally verify this attack on several locked circuits with various number of primary inputs and outputs and with various number of gates. Except for the random placement of the key gates we evaluate also the positioning with chaining elimination. The obtained and presented results show that we were able to unlock 10 of 11 circuits within few minutes on a common PC.