: In this paper we present an optimization of the planar manufacturing scheme for stretch-free, shape induced metal interconnects to simplify the fabrication with the aim of maximizing the flexibility in the structure regarding to stress and strain. The Formation of trenches between silicon islands are actively used in the lithographic process to create arc shape structures by spin coating resist into the trenches. The resulting resist form is used as a template for the metal lines, which are structured on top. Because this arc shape is beneficial for the flexibility of these bridges. The trench depth as a key parameter for the stress distribution is investigated by applying numerical simulations. The simulated results show that the increase in penetration depth of the metal bridge into the trench increases the tensile load which is converted into a shear Force Q(x), that usually leads to increased strains the structure can generate. For the fabrication the filling of the trenches with resist is optimized by varying the spin speed. Compared to the theoretical resistance, the current-voltage measurements of the metal bridges show a similar behavior and almost every structural variation is capable of functioning as a flexible electrical interconnect in a complete island-bridge array.

We prove an analog of the removable singularity theorem for bounded harmonic functions on stratified sets. The harmonic functions are understood in the sense of the soft Laplacian. The result can become one of the main technical components for extending the well-known Poincaré–Perron’s method of proving the solvability of the Dirichlet problem for the soft Laplacian.

In this study, the degradation characteristics of radio-frequency (RF) low-noise amplifier (LNA) based on silicon-germanium (SiGe) heterojunction bipolar transistors (HBTs) due to total ionizing dose (TID) are investigated. The small-signal equivalent model of a SiGe HBT is utilized to analyze circuit-level performance including the input and the output matching and noise figure (NF). As a target circuit, an LNA with a cascode common-emitter stage with emitter degeneration is studied and the equation of each performance parameter is derived. The RF LNA fabricated using commercial 350 nm SiGe technology was exposed to X-ray irradiation with the total dose up to 3 Mrad (SiO2). The experimental results exhibit that modeled device parameters estimate the degraded circuit performance. In addition, the relative impact of each parameter on the circuit metrics is revealed, which is expected from the derived design equations. The key device parameters for modeling TID-induced circuit degradations include the base resistance, the transconductance, and the base-to-emitter capacitance.

This paper presents an 8x8 channel optoelectronic readout array (ORA) realized in a 180-nm CMOS process for the applications of short-range light detection and ranging (LiDAR) sensors. We propose several circuit techniques in this work including an amplitude-to-voltage (A2V) converter that reduces the notorious walk-errors by intensity compensation, and a time-to-voltage (T2V) converter that acquires the linear slope of the output signals by exploiting a charging circuit, thus extending the input dynamic range significantly from 5 uApp to 1.1 mApp, i.e. 46.8 dB. These results correspond to the maximum detection range of 8.2 meters via the action of the A2V converter and the minimum detection range of 56 centimeters with the aid of the proposed T2V converter. Optical measurements utilizing an 850-nm laser diode confirm that the proposed 8 x 8 ORA with 64 on-chip avalanche photodiodes (APDs) can successfully recover the narrow 5-ns light pulses even at the shortest distance of 56 centimeters. Hence, this work provides a potential CMOS solution for low-cost, low-power short-range LiDAR sensors.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

This study extends the CGAN-based MODIS cloud vertical-profile (64×64-scene, about 70km width×15km height) retrieval technique developed by Leinonen et al. (2019) [1] to construct seamless 3D cloud fields for the MODIS granules [2]. Firstly, the accuracy and spatial continuity of the Leinonen et al. [1] retrievals are statistically evaluated. Then, according to the characteristics of the retrieval error, a spatially overlapping-scene ensemble generation method and a bi-directional Ensemble Binning Probability Fusion (CGAN-BEBPF) technique are developed, which improves the CGAN retrieval accuracy and support to construct seamless 3D clouds. The CGAN-BEBPF technique involves three steps: cloud masking, intensity scaling, and optimal value selection. It ensures adequate coverage of the low reflectivity areas while preserving the high reflectivity cloud cores. The technique is applied to retrieve the 3D cloud fields of Typhoon Chaba and a multi-cell convective system. The cloud structures of the CGAN-BEBPF results are highly consistent with the ground-based radar observations. It can retrieve weak clouds at the top levels of convective storms and hurricanes that were missed by ground-based radars and fill the gaps of the ground-based radar lower-level PPI scan. Overall, CGAN-BEBPF can be automated to retrieve the rich informative 3D structures of typhoons and severe convective systems over the oceans along the MODIS swath, which certainly presents great value for improving maritime and near-shore typhoons and convection prediction and other cloud-sensitive applications.

Emerging semiconductor devices often lack accurate analytical models. The same is usually true of any devices working under extreme conditions like cryogenic temperatures. The usual workaround involves the use of approximation models, usually based on lookup tables or neural networks individually fitted to measurement data. In the case of experimental devices or ones working under extreme conditions, the number of units available for measurement is limited. As a result, the number of approximation-model instances is too small to enable a statistical simulation of even middle-sized circuits, which is a necessary step in integrated-circuit design since it provides the realistic picture of the circuit’s behavior in the presence of manufacturing process variations. Approximation models using structure parameters as inputs do exist in the literature, but are only useful if the end user knows the statistical distributions of those parameters, which is not usually the case. We propose a technique based on generative machine learning, namely the variational autoencoder, that uses only a small sample of devices to capture the essential features of their I–V curves under process variations and subsequently generates an arbitrary number of similarly disturbed curves. The model trained on as few as 20 instances per device type is shown to precisely reproduce the distributions of period and power consumption of a ring oscillator.

Rubella infection is typically mild or asymptomatic except when infection occurs during pregnancy. Infection in early pregnancy can cause miscarriage, stillbirth, or congenital rubella syndrome. Only individuals that are still susceptible to rubella infection during child-bearing age are vulnerable to this burden. Rubella containing vaccine (RCV) is safe and effective, providing life-long immunity. However, average age-at-infection increases with increasing vaccination coverage, which could potentially lead to increased disease burden as well, if the absolute risk of infection during child-bearing age increases. Dynamics of rubella transmission were explored using EMOD, a software tool for building stochastic, agent-based infection models. Simulations of pre-vaccine, endemic transmission of rubella virus introduced RCV at varying levels of coverage to determine the expected future trajectories of disease burden. Introducing RCV reduces both rubella virus transmission and disease burden for a period of around 15 years. Increased disease burden is only possible more than a decade post-introduction, and only for contexts with low current burden and high transmission intensity. Low or declining rubella virus transmission intensity is concurrently associated with both greater disease burden and greater vaccine effectiveness. The risk of increasing burden through vaccination only exists for locations with persistently high infectivity, high connectivity, and high fertility. A trade-off between the risk of a small, future burden increase and a large, immediate burden decrease strongly favors RCV introduction.

This paper introduces a systematic approach to the design of Direct Current-to-Digital Converter (DCDC) specifically engineered to overcome the limitations of traditional current measurement methodologies in System-on-Chip (SoC) designs. The proposed DCDC addresses critical challenges such as high power consumption, large area requirements, and the need for intermediate analog signals. By incorporating a current mirror in a cascode topology and managing the current across multiple binary-sized branches with the Successive Approximation Register (SAR) logic, the design achieves precise current measurement. A simple comparator, coupled with an isolation circuit, ensures accurate and reliable sensing. Fabricated using the TSMC 180 nm process, the DCDC achieves 8-bit precision without the need for nonlinearity calibration, showcasing remarkable energy efficiency with an energy per conversion of 1.52 pJ, power consumption of 117 µW, and a compact area of 0.016 mm². This innovative approach not only reduces power consumption and area, but also provides a scalable and efficient solution for next-generation semiconductor technologies. The ability to conduct online measurements during both standard operations and in-field conditions significantly enhances the performance and reliability of SoCs, making this DCDC a promising advancement in the field.

Based on the minimum conduction band edge caused by the minimum channel potential resulting from the quasi-3D scaling theory and the 3D density of state (DOS) accompanied by the Fermi-Dirac distribution function on the source and drain sides, a unified semiconductor-device-physics-based ballistic model is developed for the threshold voltage of modern multiple-gate (MG) transistors, including FinFET, W-gate MOSFET, and Nanosheet (NS) MOSFET. It is shown that the thin silicon, thin gate oxide, and high work function will alleviate the ballistic effects and resist the threshold voltage degradation. Besides, as the device dimension is further reduced to give rise to the 2D/1D DOS, the lowest conduction band edge is hence increased to resist the threshold voltage degradation. The nanosheet MOSFET exhibits the largest threshold voltage among the three transistors due to the smallest minimum conduction band edge caused by the quasi-3D minimum channel potential. Compared to P-type MOSFET (P-FET), the N-FET shows more threshold voltage because the electron has a more effective mass than the hole

Plasmonic sensors have great potential for widespread usage, but the prohibitive cost of noble metals restrains the wider adoption of this technology. The aim of our study is to develop a cost-effective Al-based alternative to plasmonic detectors commonly based on noble metals. We considered a structure that consists of a Si p-n junction with an overlying grating-relief aluminum layer. The investigation of the infrared plasmonic resonance dependency on the structure geometric parameters and optimization of the fabrication process allowed us to determine optimal parameters for photodetection enhancement. The resonance photoresponse of optimized aluminum-based plasmon-polariton photodetector was significantly improved and became comparable to noble metal-based analogs. Our results can be used for the creation of cost-effective high-sensitivity plasmonic sensors.

In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

The interest in the Spark Plasma Sintering (SPS) technique has continuously increased over the last few years. This article shows the possibility of the development of a SPS device used for material processing and synthesis both in both scientific and industrial applications. This work presents an example of processing Arc-Meleted (half-Heusler, cobalt triantimonide) and SHS-synthesized semiconductors (bismuth telluride) materials with SPS device. The system functionalities expansion is presented, showing the possible way of increasing the information amount obtained about SPS processes and using the SPS apparatus for conducting synthesis of materials and increasing reproducibility and accuracy of process parameters control.

The effective macroscopic model describing interactions of a viscous compressible heat-conducting fluid and a two-level fine bristly thermoelastic structure is derived from microstructure by means of the Allaire–Briane multi-scale convergence method. This new model naturally generalizes the isothermal formulation earlier constructed by the authors in 2020, see in Siberian Electronic Mathematical Reports, vol. 17 (https://doi.org/10.33048/semi.2020.17.100). In applications, the established model can be used, for example, in description, with account of heat transfer phenomemon, of airflow near surface of plant’s leaf, in simulation of epithelium surfaces of blood vessels, and in design of biotechnological devices operating in liquids.

A new circuit model of the self-powered device for heart rate measurement is presented in this paper. This device consists of piezoelectric energy harvester (PEH), power management circuit (PMC) with energy storage, microcontroller, Photoplethysmography (PPG) sensor, and Wi-Fi module. The PEH is placed under the insole to harvest the pressure energy from human foot-step to generate ac power. In our model, a PEH is represented by sine voltage source, where its parameters were taken from experiments with 20 volunteers. The PMC is simplified by a switch with gain δ placed in series with the main circuit. The model of the main circuit is RC elements in parallel, where C is the capacitance of the storage device, and R is the equivalent parallel resistance of the microcontroller, PPG sensor, and Wi-Fi modules, respectively. The value of R depends on the power and current absorbed by those modules during sleep, deep sleep, sense, and transmit modes which collected from the datasheet. Finally, the proposed circuit model of the self-powered device was built and simulated in SPICE. The simulation results were compared with the laboratory experiment using commercial devices. Based on the results, the proposed model had small gaps compared to the real self-powered devices in terms of average current, voltage, power and efficiency.

Empirically based modeling is an essential aspect of design for a wave energy converter. These models are used in structural, mechanical and control design processes, as well as for performance prediction. The design of experiments and methods used to produce models from collected data have a strong impact on the quality of the model. This study considers the system identification and model validation process based on data collected from a wave tank test of a model-scale wave energy converter. Experimental design and data processing techniques based on general system identification procedures are discussed and compared with the practices often followed for wave tank testing. The general system identification processes are shown to have a number of advantages. The experimental data is then used to produce multiple models for the dynamics of the device. These models are validated and their performance is compared against one and other. While most models of wave energy converters use a formulation with wave elevation as an input, this study shows that a model using a hull pressure sensor to incorporate the wave excitation phenomenon has better accuracy.

Titanium alloys belong to the metal biomaterials that are one of the most widely used in medicine. In recent years, in order to reduce the use of vanadium, Ti6Al4V alloy is increasingly replaced by Ti6Al7Nb alloy. In addition, to ensure the best possible biocompatibility, its surface is subjected to appropriate modifications, for example, anodic oxidation. Despite the extensive use of anodic oxidation of titanium implants in orthopedics, there are few works focused on a detailed analysis of the chemical composition of the surface layers. In addition, the effect of treatments before anodic oxidation on the properties of the produced layer has not been analyzed. Thus, the purpose of this study was to analyze in detail the chemical composition of the passive layer of Ti6Al7Nb alloy obtained by anodic oxidation preceded by sandblasting. Moreover, the physicochemical properties of the analyzed surface affecting biocompatibility were determined. For this purpose, surface observation, wettability and roughness tests, microhardness tests, electrochemical tests and phase composition analysis were carried out. In addition, the preclinical suitability, of the surface modified in this way, was evaluated by cytotoxicity tests.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

The biological synthesis of nanoparticles has been emerging as an environmentally benign and eco-friendly method owing to its cost-effectiveness and high efficiency. Recently, the biological synthesis of semiconductor and metal-doped semiconductor nanoparticles with enhanced photocatalytic degradation efficiency and anticancer and antibacterial properties have gained tremendous attention. In pursuit of this purpose, for the first time, we biosynthesized zinc oxide (ZnO) and silver/ZnO nanocomposites (NCs) as semiconductor and metal-doped semiconductor nanoparticles, respectively, using the cell-free filtrate (CFF) of Lysinibacillus sphaericus bacterium. The biosynthesized ZnO and Ag/ZnO were characterized by various techniques such as ultraviolet-visible spectroscopy, X-ray diffraction, Fourier-transform Infrared spectroscopy, Field-emission scanning electron microscopy, transmission electron microscopy, and photoluminescence spectroscopy. The photocatalytic degradation potential of these semiconductor/metal-semiconductor nanoparticles was evaluated against the degradation of azo dye methylene blue (MB) under simulated solar irradiation. Ag/ZnO showed 90.7 ± 0.91% photocatalytic degradation of MB, compared to 50.7 ± 0.53% by ZnO in 120 min. The cytotoxicity of ZnO and Ag/ZnO on human cervical HeLa cancer cells was determined using an MTT assay. Both nanomaterials exhibited cytotoxicity in a concentration-dependent and time-dependent manner on HeLa cells. The antibacterial activity was also determined against Gram-negative (Escherichia coli) and Gram-positive (Staphylococcus aureus). Compared to ZnO, Ag/ZnO NPs showed higher antibacterial activity. Hence, the biosynthesis of semiconductor nanoparticles could be a promising strategy for developing hybrid metal/semiconductor nanomaterials for different biomedical and environmental applications.

Organosilicate glass (OSG) films are a vital component in modern electronic devices, with their electrical properties playing a crucial role in device performance. This comprehensive review systematically examines the influence of chemical composition, vacuum ultraviolet (VUV) irradiation, and plasma treatment on the electrical properties of OSG films. Through an extensive survey of literature and experimental findings, we elucidate the intricate interplay between these factors and the resultant alterations in electrical conductivity, dielectric constant, and breakdown strength of OSG films. Key focus areas include the impact of diverse organic moieties incorporated into the silica matrix, the effects of VUV irradiation on film properties, and the modifications induced by various plasma treatment techniques. Furthermore, we discuss the underlying mechanisms governing these phenomena, shedding light on the intricate molecular interactions and structural rearrangements occurring within OSG films under different environmental conditions. This review not only consolidates existing knowledge but also identifies gaps in understanding and suggests avenues for future research, thereby advancing our comprehension of OSG film behavior and paving the way for enhanced performance in next-generation electronic and photonic devices.

The fractional advection-dispersion equation FADE plays an important role, especially in explaining the process of solute-transport in natural porous media with different degrees of heterogeneity. However, studies of the flow and transport of contaminants in the underground environment are based on the knowledge of many functional parameters of the subsoil. The delay factor caused by nonlinear absorption is one of these parameters inheriting significant ambiguities in its estimation in heterogeneous media. In the study, a fractional advection-dispersion FADE model was developed by the implicit Euler method, based on a Grunwald and Caputo-Liousville approximation to explicitly evaluate and simulate the transport mechanism of contaminants in media with unsaturated porous materials subjected to a nonlinear sorption model. Better solute mass retention was observed for fractional advection-dispersion FADE model. Moreover, the absorption parameter of the retardation coefficient has a better impact on the motion of the solute in a saturated porous medium. In other words, it has a significant effect on the dispersion of pollutants in aquifers. This study highlights the need to characterize the aquifer to predict solute transport in porous media.

The utilization of optical antennas for active control of far-field radiation at the subwavelength scale is crucial in various scientific and technological applications. We propose a thermally tunable disk design of indium tin oxide (ITO) and aluminum gallium nitride (Al0.18Ga0.82As), enabling a switch between absorption and scattering. Furthermore, the control of far-field radiation pattern can be easily realized by combining ITO and Al0.18Ga0.82As to enhance or suppress emission. Our results demonstrate that hybrid structure can be dynamically tuned with temperature variations. In the proposed design, a frequency is achieved at the epsilon-near-zero wavelength of 1240 nm. The thermal tunability of hybrid structure introduces new multifunctional possibilities for light manipulation, thereby enhancing the potential applications of new devices in the near-infrared range.

This study aims to investigate the psychological cognitive mechanisms of rural residents amidst the renewal of suburban historical and cultural villages by examining the interplay between nostalgia, collective memory, subjective well-being and place identity in rural tourism destinations. Using Naobao Village as a case study—a suburban historical and cultural village in Hohhot, Inner Mongolia, this research employs a comprehensive approach integrating experimental methods and questionnaire surveys. The findings demonstrate that analyzing the interaction among the four emotions can elucidate the psychological cognitive mechanism of residents. Moreover, it uncovers that tourism effects significantly influence residents' perception of their living environment with positive effects on collective memory, subjective well-being and place identity. In the theoretical model for generating psychological cognition among residents in suburban historical and cultural villages, subjective well-being and collective memory play crucial mediating roles. This study provides a theoretical foundation and practical guidance for spatial reconstruction and cultural evolution of tourist landscapes in suburban rural tourist destinations.

This review is focused on the current status of quantitative MR (qMR) of skeletal muscle. The first section covers the techniques of qMR in muscle with the focus on each quantitative parameter, the corresponding imaging sequence, discussion of the relation of the measured parameter to underlying physiology/ pathophysiology, the image processing and analysis approaches, and studies on normal subjects. We cover the more established parametric mapping from T1 weighted imaging for morphometrics including image segmentation, proton density fat fraction, T2 mapping, diffusion tensor imaging to emerging qMR features such as magnetization transfer including ultralow TE imaging for macromolecular fraction, and strain mapping. The second section is a summary of current clinical applications of qMR of muscle; the intent is to demonstrate the utility qMR in different disease states of the muscle rather than a complete comprehensive survey.

This paper is devoted to the study of multi-dimensional integral transform with Fox H-function in the kernel in weighted spaces integrable functions in the domain R+n with positive coordinates. Mapping properties such as the boundedness, the range, the representations of the considered transformation are established.

In this paper we suggest a first ever construction of fractional integral and differential operators based on signed measures including a vector-valued case. The study focuses on constructing the fractional power of the Riemann-Stieltjes integral with a signed measure, using semigroup theory. The main result is a theorem that provides the exact form of a semigroup for the Riemann-Stieltjes integral with a measure having a countable number of extrema. The article provides examples of semigroups based on integral operators with signed measures and discusses the fractional powers of differential operators with partial derivatives.

Conditions under which compositions of component systems form a well-defined system-of-systems here are formulated at a fundamental level. Statement of what defines a well-defined composition and sufficient conditions guaranteeing such a result offers insight into exemplars that can be found in special cases such as differential equation and discrete event systems. For any given global state of a composition, two requirements can be stated informally as: 1) the system can leave this state, i.e., there is at least one trajectory defined that starts from the state, and 2) the trajectory evolves over time without getting stuck at a point in time. Considered for every global state, these conditions determine whether the resultant is a well-defined system and if so, whether it is non-deterministic or deterministic. We formulate these questions within the framework of iterative specifications for mathematical system models that are shown to be behaviorally equivalent to the Discrete Event System Specification (DEVS) formalism. This formalization supports definitions and proofs of the afore-mentioned conditions. Implications are drawn at the fundamental level of existence where the emergence of a system from an assemblage of components can be characterized. We focus on systems with feedback coupling where existence and uniqueness of solutions is problematic.

Sustainable water resource management in Bangladesh's Gumti River Basin faces challenges from climate change, urbanization, and population growth. This study aimed to calibrate and validate the HEC-HMS model for the Gumti River to enhance flood prediction and water resource planning. The model was set up using precipitation, temperature, and discharge data from 2019-2021, with SRTM elevation data for catchment delineation. Manual calibration was performed for 2019-2020, followed by validation for 2021, using parameters such as Muskingum routing and SCS Curve Number. Model performance was evaluated using R², Nash-Sutcliffe efficiency (NSE), RSR, and PBIAS metrics. Results showed satisfactory to good performance, with R² values of 0.64 and 0.68 for calibration and validation, respectively. NSE values were within the satisfactory range, while PBIAS indicated very good performance with slight underestimation. The study concludes that the calibrated HEC-HMS model provides a reliable tool for simulating the Gumti River's hydrology, though there's room for improvement. Integration with flood frequency analysis, water quality monitoring, and climate change projections is recommended for comprehensive water resource management, alongside the implementation of Sustainable Water Resource Management principles and community engagement strategies.

In this paper we describe a method which combines sentiment analysis with machine learning techniques and/or multivariate statistical analysis. By applying this methodology it is possible to classify a collection of texts into two or more groups or clusters. On the basis of a number of previously defined clusters, the novelty of the outlined approach is the use of the sentiment analysis results as input to the machine learning model or multivariate statistical analysis. Once the classifier has been obtained, we can assign a given text into one of the pre-established clusters. The groups or clusters can represent different time periods, classes of texts transcribed from different conversations, etc. The method is illustrated through an example taken from one of the two studies in which we have applied this methodology. In one of the studies, the method was used to classify press news of a volcanic eruption, while in the other study it was used to classify the conversations recorded between a chatbot with different kinds of speakers (humans or chatbots). This last study was the seminal work in which we introduced this methodology.

The main purpose of our research is the evaluation of the efficacity of solvent polarity on phenolic composition, as well as the antibacterial, and antioxidant activities of extract of Moroccan Mentha aquatica L., leaves. To attempt these objectives, the HPLC-DAD was used to identify the biomolecules. The total amount of phenolic and flavonoid content was determined using the Folin-Ciocalteu and aluminum trichloride processes as well as the DPPH, RP, and TAC tests were used to evaluate the antioxidant capabilities. In addition, by employing both in vitro and in silico analysis through the microdilution method, the minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) of the extracts were assessed against multidrug-resistant bacteria. Furthermore, the High-Performance Liquid Chromatography (HPLC) analysis indicated that all extracts of M. aquatica were abundant in noteworthy phytochemical compounds, especially gallic acid, vanillic acid, chlorobenzoic acid, quercetin, and kaempferol. Furthermore, the results indicated that the total phenolic content was higher in hydroethanolic extract (62.19 ± 1.19 mg GAE/g DW) in contrast to the acetonic and aqueous extracts (22.22 ± 0.64, and 22.44± 0.57 mg GAE/g DW) respectively. Similarly, the aqueous ethanol extract contained the greatest flavonoid concentration, with values of 29.15± 0.09 mg QE/g DW when compared with the other extracts. The seam extract poses excellent antioxidant power with an IC50 of 0.06 ± 0.00 mg/mL for the DPPH test, and lower RP with EC50 of 80± 0.00 µg/ml when compared with acetonic and aqueous extract (370± 0.00 and 460± 0.01 µg/mL) respectively. Moreover, the hydroethanolic extract has a high level of TAC 75.09± 2.00 mg EAA/g DW, followed by aqueous extract carrying a value of 28.53 ± 1.36 mg EAA/g DW. The antibacterial capacity is ranged between 0.78 ± 0.05 mg/mL and 12.60 ± 0.00 mg/L. The results of the in-silico study demonstrated that quercetin, vanillic acid, and naringenin components contribute to the antioxidant capability. While gallic acid, kaempferol, and quercetin components are attributed to the antibacterial capacity.

The article provides an overview of nanocomposites and microelectronic elements used in space electronics and radiation control systems of nuclear reactors. Only those nanocomposites and microelectronic elements are taken into account that improve their characteristics in radiation fields or remain indifferent when exposed to ionizing radiation. Considering the chemical composition of the materials of these nanocomposites and microelectronic elements, it is analyzed from which radioactive materials (RM) obtained by recycling radioactive waste (RW) such composites and microelectronic parts can be made. Thus, an alternative way of radioactive waste disposal is proposed, when these wastes are used in the form of microelectronic elements designed to operate under conditions of cosmic radiation.

This paper presents laboratory devices on which experimental measurements were carried out to prove the validity of the assumption about the reduction of vibrations transmitted to the conveyor belt structure generated by the impact forces of falling material grains in the places of transfer or on the hoppers of conveyor belts. In order to limit damage to the conveyor belts caused by the impact of the sharp edges of material grains, conveyor belts are supported by impact rollers or impact rubber rods in the places of transfers and on the hoppers of belt conveyors. The flattened ends of the impact rollers are inserted into the grooves of steel brackets installed on the supports of the fixed conveyor idlers of a conventional design. In this paper, a special modification of the fixed conveyor idler is presented, which consists of inserting plastic brackets into the structurally modified roller axle holders of the fixed conveyor idler. Measurements were carried out on the first laboratory device, which showed that the specially modified fixed conveyor idler resulted in a higher damping of up to 15% of the impact forces of the falling weight on the rubberized hoop of the impact roller shell compared to the conventional fixed conveyor idler design. Measurements carried out on the second laboratory device show that the effective vibration velocity values detected at the points where the impact roller axis fits into the fixed roller table holder, i.e. points B and D, are higher than when using plastic brackets, up to 6% for a 108 mm diameter roller, compared to steel impact roller brackets.

The band gap research in graphene is still a very important topic for materials application. Here, we report a band gap opening and p-type semiconducting property of the graphene by using an electrochemical doping on graphene surface. The manganese-oxide nanopar-ticles adsorbed on the graphene were used as the dopants in an electrolyte, which induce the band gap opening and the change of electronic structure. In addition, the fabricated graphene FET shows the p-type semiconductor behaviors. The temperature dependent conductivity of the p-type doped graphene at applied potential of 1.5 V during electro-chemical doping shows the formation of band gap of 0.23 eV, which is obtained from the fitting of conductivity equation. The semiconducting properties of manganese-oxide doped graphene is attributed to the formation of manganese-oxide nanoparticle on the surface of graphene.

Semiconductor technology is the backbone of modern innovations, propelling technological advancements in industries such as electronics, renewable energy, telecommunications, and health-related fields. This review expatiates the fundamental properties and working principles of semiconductor materials that determine device performances, while also tracing the historical trajectory of these technologies from the inception of the transistor to pioneering developments, such as tunnel gate transistors and 2D materials like graphene. Specific challenges such as material constraints, manufacturing complexities, and environmental impacts are highlighted. In response to such challenges, measures for the improvement of sustainability, energy saving, and waste minimization in production are discussed. The research also responds to the extended effects of globalization, including the disruptions like COVID-19 pandemic, on supply chain and emphasizes on the importance of developing resilient production frameworks for future growth. Additionally, this work highlights emerging technologies, including quantum computing, artificial intelligence integration, and nanotechnology, which are poised to redefine data processing and storage. The research vindicates the necessity of innovation and sustainability as the key motivators for enhancing the capabilities of semiconductors and global technology.

Continuous-flow microwave heating stands out for its ability to rapidly and uniformly heat substances, making it widely applicable in chemical production. However, in practical applications, the permittivity of the heated liquid changes dramatically as the reaction progresses, affecting the efficiency and uniformity of continuous-flow heating. Herein, this work presents a novel microwave heating device based on coaxial structure for high-performance heating. Our approach commenced with the development of a multi-physical field model, incorporating a spiral polytetrafluoroethylene (PTFE) as a water channel and the coaxial waveguide as a container was established. The analysis shows that the uniform distribution of the sectional electric field of electromagnetic waves in the TEM mode within the coaxial structure can enhance heating uniformity. Then, a continuous-flow microwave heating system for different liquid loads was established, and experimental measurements were conducted. The heating efficiency for all loads exceeded 90%, which basely matched the simulation results, validating the accuracy of the model. Finally, the heating efficiency and uniformity under different permittivity loads were analyzed, as well as the impact of channel radius on heating efficiency. The device demonstrated high heating efficiency and stable heating uniformity across different loads. This continuous-flow microwave device is suitable for chemical research and production, contributing to the promotion of microwave energy applications in the chemical industry.

Umbria is an Italian region with a highly fragmented water supply, with many small water distribution systems fed by local sources. The chlorination in these small water systems faces many difficulties related to the high demand variation, low economic relevance, and access to infrastructures. As a result, there are many noncompliances with the quality of the supplied water, which causes a decrease in the performance indicators and tariff. This research investigates the possibility of using a low-cost chlorination system to consider different environmental conditions (e.g., temperature variations of water and environment, pH, ...) and discontinuous consumption. A device for this specific use is developed and tested by laboratory tests and is ready for use in the field.

Glucose is a simple sugar molecule. The sugar molecule is chemically symbolised as C6H12O6. This means that the glucose molecule contains 6 carbon atoms (C), 12 hydrogen atoms (H) and 6 oxygen atoms (O). In human blood, the molecule glucose circulates as blood sugar. Normally after eating or drinking, our body breaks down the sugars in food and uses them to obtain energy for our cells. To do this, our pancreas produces insulin. Insulin "pulls" sugar from the blood and puts it into the cells for use. If someone has diabetes, their pancreas can't produce enough insulin. As a result, the level of glucose in the blood rises. This can lead one to many potential complications, including blindness, disease, nerve damage, amputation, stroke, heart attack and damage to blood vessels etc. In this study, a non-invasive method for monitoring blood glucose has been developed and is therefore easily usable. The device developed can measure the glucose level continuously and eliminates the disadvantages of the invasive system. Near-IR sensors (optical sensors) were used to estimate the concentration of glucose in the blood; these sensors have a wavelength of 940 nm. The sensor is placed on the tip of the finger and the output of the optical sensor is then connected to the microcontroller at the analogue input. Another sensor used, but only to provide more medical information was the heartbeat sensor. After processing and regression analysis, the glucose level is predicted, and data is sent via the Bluetooth network to a developed APP. The results of the implemented device were compared with available invasive methods. The study consists of a hardware platform inserted into an armband and then a small black parallelepiped-shaped box in which the optical sensors are inserted. The hardware consists of a microcontroller, a Near-IR optical sensor, a heartbeat sensor and a Bluetooth module.

Due to its large hole mobility, Organic Rubrene (C42H28) has attracted research questions on its applications in electronic devices. In this work, extensive first-principles calculations were made to predict some temperature and doping dependent properties of Organic Semi- conductor Rubrene. We use Density Functional Theory (DFT) to investigate the electronic structure, elastic and transport properties of the Orthorhombic phase of the Rubrene compound. The calcu- lated band structure shows the Orthorhombic phase has a direct bandgap of 1.26 eV. From the Vickers hardness (1.080 GPa), our calculations show that Orthorhombic Rubrene is not a super hard material and can find useful application as a flexible semicon- ductor. The calculated transport Inverse Effective Mass and Elec- tronic Fitness Function show that the Orthorhombic Rubrene Crystal Structure is a p-type thermoelectric material at high temperatures.

This paper presents an on-device semi-supervised human activity detection system that can learn and predict human activity patterns in real time. The proposed semi-supervised learning (SSL) framework uses sparsely labelled user activity events acquired from Inertial Measurement Unit (IMU) sensors installed as wearable device. The objective is to learn classification of multiple classes of human activities in real-time. The proposed cluster-based learning model in this approach is trained with data from the same target user, thus preserving data privacy while providing personalized activity detection services. Two different cluster labelling strategies, namely, population-based, and distance-based, are employed to achieve the desired classification performance. A comparative study of these strategies has been presented in terms of classifiability and classification accuracies. The proposed system is shown to be computationally efficient, which is relevant in the context of limited computing resources on typical wearable devices. The trade-off between classification accuracy and computation complexity is analyzed for different algorithmic hyper-parameters and other system parameters. Extensive experimentation and simulation study have been conducted on a multi-user human activity data from the public do-main in order to validate the proposed learning paradigm.

This article presents a new input device for spastic patients and others with similar symptoms. The sensor consists of a disc used to determine positions and can replace standard joysticks in medical devices such as electric-powered wheelchairs. Using a standard joystick while operating a powered wheelchair can result in dangerous situations when spastic movements occur and extremities cramp making them uncontrollable. To avoid this, a disc was developed that can be controlled with any body part. By shifting weight (x- and y-axis) the disc can tilt in any direction creating a proportional output signal and can also be pushed down in the center (z-axis) to open a menu on a screen for example. When spasms occur it is impossible for users to get stuck on the input device because the disc is flat and can be mounted within a control panel. Body parts coming into contact with the disc would merely slide across the disc without triggering unintentional actions. The sensor presented here is also adaptive and can be adjusted to fit a user’s strength and range of motion. This proposal aims to develop an input device that enables spastic patients to operate sensitive systems safely.

The purpose of this article is to present an IoT architecture implemented in an intelligent environment, focusing on the optimization of initial conditions and device management. A general control system was developed using an open-source platform, integrating aWi-Fi network and YAML coding to enable communication and control of the IoT architecture devices. The implementation includes actuators, sensors, and control devices that, through a graphical interface, allow the visualization of the historical record of activities and real-time measurements of connected devices. The design includes specific mechanisms and the analysis of materials through tensile tests on specimens, following the ASTM E8 standard, and deformation test simulations, in which PLA demonstrated better performance compared to materials like ABS and resin. The significance of the implemented IoT system lies in an energy saving of 58% compared to conventional structures. Additionally, the study of response times for network connections showed that using an Ethernet cable resulted in a response time of 1.21 seconds, representing a reduction of 1.65 seconds compared to the second lowest value obtained.

The effect of wave forces on the structural safety of fixed oscillating water-column (OWC) devices is critical. In this study, a three-dimensional numerical model of an oscillating water column (OWC) device is constructed using the computational fluid dynamics software OpenFOAM. Subsequently, the hydrodynamic performance of the numerical model is comprehensively validated. Finally, the hydrodynamic performance data are analyzed in detail to obtain meaningful conclusions. The results indicate that the horizontal wave force on the OWC device is approximately 6.6 to 7.9 times greater than the vertical wave force, whereas the lateral wave force is relatively small. Both the horizontal and vertical wave forces decrease as the relative water depth increases under a constant wave period and height. The horizontal wave force increases linearly with the wave height, whereas the vertical wave force increases with the square of the wave height. In addition, the highest dynamic water pressure is observed at the interface between the water surface and device, both within and outside the front wall of the gas chamber. The dynamic water pressure at different locations on the front chamber increases and subsequently decreases as the wave frequency increases.

The paper investigates into the intricacies of semiconductor manufacturing, a highly complex process entailing a wide array of subprocesses and diverse equipment. Semiconductors are miniaturized integrated circuits comprising numerous components. The semiconductor manufacturing process begins with the thin disc-shaped silicon wafers. On each wafer, up to thousands of identical chips can be prepared depending upon the diameter of the wafer to build up the circuits layer by layer in a wafer fab. The size of the semiconductors requires a high number of units to be produced, thus necessitating a large amount of data to control for improving the semiconductor manufacturing process. Therefore, the collection and analysis of the equipment data, process data, and machine history data throughout the manufacturing process are required to diagnose faults, monitor the process, and manage the manufacturing process effectively. This research is focused on improving the semiconductor manufacturing process through a rigorous analysis of collected manufacturing process data, employing statistical process control (SPC), data mining techniques, and data-driven decision models. The project's primary objective is to increase the manufacturing process stability and productivity by utilizing the latest data-driven technologies in the scientific community. A structured review was undertaken, exploring contemporary data-driven methodologies in semiconductor manufacturing process improvement, specifically pertaining to process capability, product yield rate, and process stability. This review accentuates a comprehensive evaluation of data-driven methodologies applicable to conventional semiconductor manufacturing facilities, aiming to drive substantial process improvements. It features a detailed demonstration facilitating the selection of optimal semiconductor manufacturing processes to enhance overall operational performance. This study of process improvement in the semiconductor manufacturing steps through the application of data-driven methodologies will be effective in delivering advanced, real-time, and proactive control decisions throughout the manufacturing facilities. This endeavor is expected to promptly provide critical insights for enterprise manufacturing decision-makers to reduce manufacturing cycle time, improve the product yield rate, and increase the overall efficiency of the manufacturing process.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

As well known, the torque produced by a rotating motor generates an opposite and equal reaction torque in the machine casing that must be transmitted to the base. In many applications, especially when the reaction moment has high values, it is necessary to apply some constructive solutions, which in certain cases are difficult to implement. In this context, the need to reduce the reaction moment from drive motors is a challenging topic, which has not been completely exhausted. In this paper, the authors present an original concept of a device which uses the centrifugal force generated by some equidistantly placed weights on a chain drive, for reducing the reaction torque of the motor used for driving a rotating tool. The proposed system is capable to produce a supplementary torque which can be added to driving moment. Due to this fact, by using this system, the power of the driving motor can be decreased, with the consequence of reducing the reaction moment, that must be absorbed by the base.

The present overview of spin-dependent phenomena in nonmagnetic semiconductor microparticles (MPs) and nanoparticles (NPs) with interacting nuclear and electron spins is aimed at covering a gap between the basic properties of spin behavior in solid-state systems and a tremendous growth of the experimental results on biomedical applications of those particles. The first part of the review represents modern achievements of spin-dependent phenomena in the bulk semiconductors from the theory of optical spin orientation under indirect optical injection of carriers and spins in the bulk crystalline silicon (c-Si) – via numerous insightful findings in the realm of characterization and control through the spin polarization – to the design and verification of nuclear spin hyperpolarization in semiconductor MPs and NPs for magnetic resonance imaging (MRI) diagnostics. The second part of the review is focused on the electron spin-dependent phenomena in Si-based nanostructures, including the photosensitized generation of singlet oxygen in porous Si and design of Si NPs with unpaired electron spins as prospective contrast agents in MRI. The experimental results are analyzed by considering both the quantum mechanical approach and several phenomenological models for the spin behavior in semiconductor/molecular systems. Advancements and perspectives of the biomedical applications of spin-dependent properties of Si NPs for diagnostics and therapy of cancer are discussed.

The main contribution of this paper is to develop a graphical tool to evaluate the suitability of a candidate parametric model to fit a data set. The practical motivation is to check the adequacy of the so called SAINT model proposed in Jarner and Kryger (2011). This model has been implemented in practice by an important European pension fund concerned with setting annuity reserves for all current or former employees of Denmark. So, one particular relevant question is whether this mortality model is actually fitting old-age. Our graphical test can be described as follows. First we transform the data by means of the parametric model which is being evaluated. Should the model be correct, the transformed data will be in accordance with an Exponential distribution with rate 1. Then we construct a family of local linear hazard estimates based on the data on the transformed scale. Finally we use the statistical tool SiZer to assess the goodness-of-fit of the Exponential distribution to the data on the transformed scale. If the model is correct the SiZer map should not reveal any significant feature in the family of kernel estimates. Our method allow us to establish a diagnostic regarding the validity of the SAINT model when describing mortality patterns in four different countries.

The research that we are referring to examines the morphological, structural, and optical characteristics of kesterite (Cu1-xAgx)2ZnSnS4 (CAZTS) thin films, which are produced using a process known as thermal evaporation (TE). The study's main goal was to determine how different Ag contents affect the characteristics of CAZTS systems. X-ray diffraction (XRD) and Raman Spectroscopy: were used to confirm the crystal structure of the CAZTS thin films. Using a mathematical model of spectroscopic ellipsometry, the refractive index (n) represented the part of the complex refractive index, the extinction coefficient (k) portrayed the imaginary one, and also the energy band gap of the fabricated films were all calculated. The energy band gap of the thin films was also calculated. This is a crucial parameter for solar cell applications, as it determines the wavelength of light that the material can absorb. The energy band gap was found to decrease from 1.74 eV to 1.55 eV with increasing Ag content. The ITO/n-CdS/p-CAZTS/Mo heterojunction was well constructed, and the primary photovoltaic characteristics of the n-CdS/p-CAZTS junctions were examined for use in solar cells. Different Ag contents of the CAZTS layers were used to determine the dark and illumination (current-voltage) characteristics of the heterojunctions. The study's findings collectively point to CAZTS thin layers as potential absorber materials for solar cell applications.

As motor capacity and rated voltage increase, the demand for motor insulation also increases. Additionally, the electric field distribution at the end of a large-scale hydro generator is extremely non-uniform, and corona discharge readily occurs. This destroys the main insulation, which significantly affects the service life of electrical machinery. Thus, the regulation of the electric field concentration at the end of a large-scale hydro generator needs to be addressed. There are many problems in resistance–capacitance chain model research. Particularly, these models cannot accurately reflect the insulation, corona structure, and electric field distribution in electrical machinery. Additionally, the corner electric field and loss distributions cannot be obtained, leading to a higher calculation error. The electric field distribution at the motor end and the loss distribution were analyzed using the finite-element method. First, by applying the basic principles of electric circuits and electromagnetic field theory, we calculated the electric field distribution at the stator bar end. Second, a 3D model of the stator bar was built using Creo Parametric, yielding a model that is more closely related to the prototype wirebar model. Then, the potential, electric field, and loss distributions around the stator bar were simulated by using COMSOL simulation software. The effects of the circular arc corner, nonlinearity coefficient, anti-corona coating length, and resistivity of the stator bar on the electric field distribution at the motor end were explored.

Structural and functional materials are subjected to harsh oxidizing environments that lead to a rapid decline in their surface chemical stability. At high-temperatures, the diffusion of atoms is erratic; thus, the reactive elements (REs) get a chance to migrate to the surface and look for oxygen-reactive sites. Their migration from the lattice sites creates vacancies in the matrix and thus weakens the bond, making the material prone to environmental degrading factors. Subsequently, the inward diffusion of oxygen, sulfur, nitrogen, or carbon may occupy these vacancies, resulting in undesired precipitation at the grain boundary, which is usually brittle. The solubility and dissociation of attacking species and corrosion products play the most critical role in corrosion in high-temperature water. To evade such situations, Ti, Al, and Cr are added in Ni/Fe-based alloys, forming a dense oxide layer on the surface that impedes further surface migration of ions. The stability of the alloys is then determined by the capability of these oxide layers to heal or reform during spalling/cracking. This review attempts to understand the migration of REs at the interfaces to prepare structural materials in any unexpected set of oxidizing service conditions. This review will also try to establish the interaction mechanism of REs novel/conventionally added in the alloys with the oxidizing elements in the environments to design better degradation-resistant high-temperature alloys.

As cardiovascular diseases continue to be a leading cause of mortality, recent-ly, wearable devices for monitoring cardiac activity have gained much interest among medical community. This paper introduces an innovative ECG monitoring system based on a single – lead ECG machine enhanced with machine learning methods. The system only processes and analyses the ECG data, but also predict potential heart disease at an early stage. The wearable device was built on the ADS1298 and a microcontroller STM32L151xD. A server module based on REST API architecture style was designed to fa-cilitate interaction with web-based segment of the system. The module is responsible for receiving data in real time from microcontroller and their deliver to web – based segment. Algorithms for analyzing ECG signals have been developed, including band filter artifact removal, K-means clustering for signal segmentation, and PQRST analysis. Machine leaning methods as Isolation Forest have been employed for ECG anomaly detection. Moreover, a comparative analysis with various machine learning methods, including lo-gistic regression, random forest, SVM, XGBoost, decision forest and, CNNs was conducted to predict cardiovascular diseases. Convoluted Neural Networks (CNN) showed an accu-racy of 0.926, proving high effectiveness in ECG data process.

Addressing the significant challenge in high-speed cotton dibbling operations in Xinjiang—specifically, the duck bill’s ("Duck bill" is a type of duck-billed bunch planting mechanism or component). shortened opening duration leading to seed throwing and floating—a new crawler-type delayed hole-forming mechanism has been designed. This mechanism extends the duck bill horizontally, thereby prolonging its opening time, enabling cotton sowing speeds of up to 6 km/h. Following agronomic principles for cotton planting, the overall layout of the crawler-type hole-forming mechanism, the structural parameters of the key components and the trajectory of the hole-forming are determined. We use the Discrete Element Method (DEM) and multi-body dynamics coupling method to simulate and analyze the motion process of the device. The fixed the tilt angle of the duck bill α(A), the depth of the duck bill hole-forming into the soil h(B), and the angle of rotation of the moving duck bill β(C) were taken as the experimental factors, with the longitudinal length of cotton seed hole (Y1) and the hole-forming depth of cotton seed hole (Y2) as the response values. The parameter range of each factor and the preliminary influence on the response value were determined through pre-experiments and single-factor simulation test. Based on RecurDyn-EDEM coupling, a quadratic regression orthogonal rotation combination simulation test was carried out. The results show that the order of the primary and secondary factors affecting the Y1 of the time-lapse hole-forming device was: A > C > B. The order of primary and secondary factors affecting the Y2 of the delayed hole forming device was: B > C > A. When the A was 2.4 °, the B was 42.4 mm, and the C was 30.5 °, the performance of the hole-forming was the best, and the Y1 was 26.4 mm, and the Y2 was 25.0 mm. The bench verification test results show that under the optimized combination of operating parameters, the average Y1 was 29.1 mm, and the average Y2 was 23.2 mm. Compared with the results of the previous coupled simulation model, the average relative errors of the two are 7.23 % and 4.36 %, respectively, indicating the accuracy and effectiveness of the established DEM simulation model and virtual test analysis. The hole-forming area and the opening time of the duck bill after the stable operation of the machine were recorded and measured. The calculated hole dislocation rate Hc was 4.33 %, which did not exceed the national standard requirement of 6 %. The qualified rate of hole distance Hx was 94.33 %, which was much higher than the national standard requirement of 80 %. The average opening time of the duck bill at a speed of 6 km/h is 0.45 s, which is much longer than the time required for cotton seeds to fall from the duck bill 0.11 s. It meets the requirements of high-speed cotton planting in China and facilitating advancements in future high-speed planter technology.

During the development of horizontal wells in bottom water reservoirs, the strong heterogeneity of reservoir permeability leads to premature bottom water breakthrough at locations with high permeability in the horizontal wellbore, and the water content rises rapidly, which seriously affects production. In order to cope with this problem, a new technology has emerged in recent years that utilizes gravel filling to block the flow in the annulus between the horizontal well and the borehole, and utilizes the Inflow Control Device (ICD) completion tool to carry out segmental water control in horizontal wells. Unlike conventional horizontal well ICD completions that use packers for segmentation, gravel pack combined with ICD completions breaks the original seg-mentation routine and increases the complexity of production dynamic simulation. In this paper, the flow in different spatial dimensions such as reservoir, gravel packed layer, ICD completion section and horizontal wellbore is modeled separately, and the annular pressure at different locations is used as the solution variable for the coupled solution, which realizes the prediction of oil production, water production and water content of gravel pack combined with ICD completions of horizontal wells. The model was used to calculate the effects of different crude oil viscosities, different reservoir permeabilities, different permeabilities of gravel packed layers, and different development stages on the water control effects of gravel pack combined ICD completions and conventional ICD completions at field conditions. This study provides a basis for using gravel pack combined ICD completions in horizontal wells in bottom water reservoirs.

In review, the operating principles of the most common bio sensing devices, detection methods and the identification sensitivity of analyzed molecules were shown. The central focus was done on hybridization analysis of nucleic acids (NA), which are considered to be one of the most important analytes in terms of diagnostic point of view. Constructions enabling to transfer the fact of formation of nucleotide probe/target complex in to detectable signal by optical, electrochemical or micromechanical (piezoelectric) sensors were presented in this review.

Techniques have been developed to determine whether a horse is in resting or running mode by measuring at least one of the following: the horse's body temperature, heart rate, oxygen saturation, and exercise level. However, the existing technology has not reached a level where a trainer can accurately assess a horse's running conditions, such as speed, acceleration, stride, limb rotation, ground impact, and frontal balance, during the training of racehorses. In addition, data is needed to quickly detect abnormalities during training and provide a basis for changing the intensity of training or deciding to give a rest to the horse. Devices that detect abnormalities in equine gait with high sensitivity will contribute to animal welfare and increase the athletic longevity of horses. This paper reports the development results of a new IoT device that acquires, processes, and analyzes information such as heart rate, position, speed, acceleration, pitch, stride, and ground contact during a training of racehorses. The purpose of this development is to provide an information on a novel processing system, device, method, and program that can analyze training condition of racehorses from multiple angles.

This paper employs the Finite Element Method (FEM) to simulate and analyze the effects of corrosion defect parameters on the stress and failure pressure of pipelines. It investigates how the boundary conditions of the pipeline model influence stress and examines the sensitivity of failure pressure to corrosion defect parameters. A nonlinear regression equation has been developed from a dataset obtained through simulation experiments to predict the failure pressure of corroded pipelines. To validate the effects of corrosion defect parameters on failure pressure, a hydrostatic test platform for an API 5L X65 pipeline with corrosion defects was established to measure stress levels and failure pressures across varying corrosion defects. The study reveals that failure pressure is negatively correlated with corrosion length and depth, while positively correlated with corrosion width. Among these parameters, corrosion depth exerts a more significant influence on the pipeline's failure pressure than corrosion length and width. Within the range of corrosion defect parameters examined, the maximum deviation of the prediction equation's results from the simulation results is 8.71%, with an average deviation of 5.81%. The standard deviation of the fitted residuals is 0.01837. Additionally, the maximum deviation between the predicted results and experimental measurements is 8.39%, with an average deviation of 7.77%. The strong agreement between the predicted results from the equation and the actual measured data underscores the effectiveness of the nonlinear regression equation.

This study fabricated piezoelectric fibers of polyvinylidene fluoride (PVDF) with graphene using near-field electrospinning (NFES) technology. A uniform experimental design table U*7 (7^4 ) was applied, considering weight percentage (1-13 wt%), distance between needle and disk collector (2.1-3.9 mm), and applied voltage (14.5-17.5 kV). We optimized the parameters using electrical property measurements and the Kriging response surface method. Adding 13 wt% graphene significantly improved electrical conductivity, increasing from 17.7 μS/cm for pure PVDF to 187.5 μS/cm. The fiber diameter decreased from 21.4 μm in PVDF/1% graphene to 9.1 μm in PVDF/13% graphene. Adding 5 wt% graphene increased the β-phase content by 6.9%, reaching 65.4% compared to pure PVDF fibers. Material characteristics were investigated using scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction analysis (XRD), contact angle measurements, and tensile testing. Optimal parameters included 3.47 wt% graphene, yielding 15.82 mV voltage at 5 Hz and 5 N force (2.04 times pure PVDF). Force testing showed a sensitivity (S) of 7.67493 log(mV/N). Fibers were attached to electrodes for piezoelectric sensor applications. Results affirmed enhanced electrical conductivity, piezoelectric performance, and mechanical strength. The optimized piezoelectric sensor could be applied to measure physiological signals, such as attaching it to the throat under different conditions to measure the output voltage. The force-to-voltage conversion facilitated subsequent analysis.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

The present work is a theoretical and experimental study of temperature effect on wavelength and threshold current. Since Semiconductor lasers are the type of lasers which uses semiconductor material as a gain medium to achieve stimulated emission of radiation. In this module, the type of semiconductor lasers use is VCSEL and laser diode. Temperature change cause Semiconductor lasers to shift its threshold current, this variation also causes a shift in output wavelength. The experimental results highly agreement with the theoretical calculations.

Electroless etching of semiconductors was elevated to an advanced micromachining process by the addition of a structured metal catalyst. Patterning of the catalyst by lithographic techniques facilitates the patterning of crystalline and polycrystalline wafer substrates. Galvanic deposition of metals on semiconductors has a natural tendency to produce nanoparticles rather than flat uniform films. This characteristic makes possible the etching of not only wafers but also particles with arbitrary shape. While it has been widely recognized that spontaneous deposition of metal nanoparticles can be used in connection with etching to porosify wafers, it is also possible to produced nanostructured powders. MACE can be controlled to produce (1) etch track pores with shapes and sizes closely related to the shape and size of the metal nanoparticle, (2) hierarchically porosified substrates exhibiting combinations of large etch track pores and mesopores, and (3) nanowires with either solid or mesoporous cores. This review discussed the mechanisms of porosification, processing advances and the properties of the etch product with special emphasis on the etching of silicon powders.

Investigations into the properties of generalized effective temperature are conducted across arbitrary dimensions. Maxwell-Boltzmann distribution is displayed for one, two, and three dimensions, with effective temperatures expressed for each dimension. The energy density of blackbody radiation is examined as a function of dimensionality. Effective temperatures for non-uniform temperature distributions in one, two, three, and higher dimensions are presented, with generalizations extended to arbitrary dimensions. Furthermore, the application of generalized effective temperature is explored not only for linearly non-uniform temperature distributions but also for scenarios involving the volume fraction of two distinct temperature distributions. Finally, the effective temperature is determined for a cryogenic system supplied with both liquid nitrogen and liquid helium.

The quest for youthful, healthy skin and full, vibrant hair has long been a driving force in the dermocosmetics field. However, traditional approaches often struggle to address the underlying causes of aging, damage, and hair loss. Regenerative cosmetics, powered by skin tissue engineering, offer a transformative alternative. This review explores the emerging field of using engineered skin tissues for cosmetic purposes, focusing specifically on their potential for anti-aging, repair, and hair restoration applications. We discuss how these technologies aim to rejuvenate aging skin by promoting collagen production, reducing wrinkles, and improving overall skin function. Additionally, the use of engineered skin for wound healing and scar reduction is examined, highlighting their potential to improve the appearance and functionality of damaged skin. Finally, we advance the exciting prospects of utilizing skin tissue engineering techniques to regenerate hair follicles, potentially offering solutions for hair loss and promoting denser hair growth.

Systematic reviews represent a powerful instrument to summarize the existing evidence in medical literature. However, articles for a systematic review are hard to identify, and mostly require a structured search of the literature through a number of databases, using keyword-based search strategies, followed by the painstaking manual selection of pieces of evidence that are pertinent to the query. A.I. algorithms may offer solutions to reduce the workload on investigators. We applied BERTopic, a newer and much-recognized transformer-based topic-modeling algorithm, to two datasets of 6137 and 5309 articles of newly published systematic reviews in the area of peri-implantitis and bone regeneration in implant dentistry. In the two datasets, BERTopic identified 14 and 22 clusters, respectively, and it automatically created labels describing the nature of the topics for each individual cluster based on semantic interpretation of their titles. Most themes regarded the query theme, but in both conditions, BERTopic also uncovered articles related to off-themes, which composed around 30% of the dataset—with sensitivity up to 0.79 and specificities of at least 0.99. Our results suggest that adding a topic-modeling step to the screening process could potentially save working hours for researchers involved in systematic reviews of the literature.

Objectives. To compare the audiological benefits of a non-implantable wearing option of a bone conduction (BC) implant mounted on an arch (SoundArc) to traditional BC hearing aids (HA) mounted on eyeglasses (BCHA) in patients with moderate to severe conductive or mixed hearing loss. Methods: A preliminary cross-sectional observational prospective cohort study was conducted at a Tertiary Audiological Department, University Hospital. Fourteen adults with conductive or mixed hearing loss (PTA at 0.5-1-2-4 KHz = 67 ± 15 dB HL) had been wearing conventional BCHA on eyeglasses for at least 3 years, and refused the surgical implantation of a BC hearing implant (BCHI). Unaided and aided pure-tone AC and BC thresholds and speech test in quiet and in noise were recorded at baseline and in two different settings: with a BCHI mounted on SoundArc®, and with their own BCHA with two couplers, mounted on eyeglasses. International Inventory for Hearing Aids [IOI – HA], the Hearing Handicap Inventory [HHIA/E], Speech, Spatial, Qualities of Hearing Scale [SSQ], a 10-scores visuo-analogic scale [VAS], and Fatigue impact scale [FIS] score were asked in both conditions. Results: a statistical significative functional gain was observed for both settings. (p=.0001) Better speech perception performances in quiet and in noise were observed with SoundArc compared to their conventional BCHA on eyeglasses (word repetition score in noise improvement of +19.3 at SNR +10 dB, p=.002; + 12.1 at SNR 0 dB, p=.006; and +11.4 at SNR -10 dB, p=.002) No significant differences were found in IOI–HA, FIS, and HHIA/E scores, while significative better SSQ scores in all domains were reported for SoundArc. (p=.0038) Conclusions: Although patients were accustomed to their BCHA on eyeglasses, the non-implanted wearable option of the BCHI proved to be a viable alternative in adult patients with conductive or mixed hearing loss unable to receive or refusing BCHI surgery.

The increasing regulatory pressure to monitor and reduce GHG emissions and air pollutants requires cost-effective methods for their surveillance. The most common technique used for scientific investigations on gas concentration monitoring in barns are accurate but expensive and with a complex maintenance. This research study analysed the potential use of a low-cost portable measurement devices for the measurement of ammonia (NH3) and carbon dioxide (CO2) concentrations in an open dairy barn. A comparison between gas concentrations acquired at different heights from the floor by using portable devices and those acquired by a photoacoustic infrared multigas spectroscope (i.e., reference measurement) in the same sampling locations was carried out to determine the precision of the low-cost portable devices. The performance of low-cost portable devices was statistically analysed by the application of the one-way analysis of variance, correlation analysis and regression analysis. The results showed a significant difference between gas concentration values at various heights from the floor for both NH3 and CO2. The correlations between concentrations acquired by the low-cost portable device and the INNOVA were statistically significant (r=0.83; P<0.001) for gas concentrations monitored at 0.4 m from the floor. Compared with the reference measurement device, the low-cost devices were effective in the monitoring of NH3 concentrations at 0.40 m from the floor though it underestimated them in the barn at increasing of the height from the floor, whereas the device was not adequate for CO2 concentrations. In detail, the relative measurement error of the low-cost devices compared to INNOVA was reduced close to the floor during NH3 concentration measurements. Within these limitations, this device could be useful for monitoring NH3 concentration in the barn and to assess variation in NH3 concentrations mainly related to the animal occupied zone. Further efforts are needed in this field of research to identify low-cost device that could simplify emission estimation from open dairy barns.

Scedosporium species are human pathogenic fungi, responsible for chronic, localised, and life-threatening disseminated infections in both immunocompetent and immunocompromised individuals. Diagnosis of Scedosporium infections currently relies on non-specific CT, lengthy and insensitive culture from invasive biopsy, and time-consuming histopathology of tissue samples. At present, there are no rapid antigen tests that detect Scedosporium-specific biomarkers. Here we report the development of a rapid (30 min) and sensitive (pmol/L sensitivity) lateral-flow device (LFD) test, incorporating a Scedosporium-specific IgG1 monoclonal antibody (mAb), HG12, which binds to extracellular polysaccharide (EPS) antigens of between ~15 kDa and 250 kDa secreted during hyphal growth of the pathogens. The test is compatible with human serum, and allows the detection of the Scedosporium species most-frequently reported as agents of human disease (Scedosporium apiospermum, Scedosporium aurantiacum, and Scedosporium boydii), with limits of detection (LOD) of the EPS biomarkers in human serum of ~0.81 ng/mL (S. apiospermum), ~0.94 ng/mL (S. aurantiacum), and ~1.95 ng/mL (S. boydii). The Scedosporium-specific LFD (ScedLFD) test therefore provides a potential novel opportunity for the detection of infections caused by different Scedosporium species.

It’s very well known that the world's attention is currently focused on the energy transition. The energy security, in addition to the drive to reduce greenhouse gas emissions in order to limit global warming, and the generalization of the access to energy, have contributed to adoption of the Moroccan Energy Strategy with a strong focus on Renewable Energies (RE). Morocco is notoriously poor in conventional fossil primary energy resources with an energy dependence on the order of 90%. The energy crisis and that resulted from Covid-19 pandemic and the geopolitical conflicts, combined compounded with steady increase in demand have heavily affected the security and the stability of the country's energy situation. The transition to RE, by strongly engaging in the implementation of several solar, wind and hydro energy projects benefiting from the country's excellent solar and wind energy potential, has made the country the leader in RE in Africa. By 2030, the share of RE in the installed capacity is expected to reach 52%. In this work, an overview of the current situation of RE (particularly solar energy) in Morocco is provided, including, the potentials, obstacles and challenges, and future perspectives. Thanks to its high solar potential location, it’s predictable that Morocco effort will be focused on this field: the Erasmus Plus Innomed Project is a virtuous example of international cooperation, aiming at create a Solar Energy Network, in synergy with EU Partners.

This study systematically addresses the challenge of accurately modeling memristors, focusing on four distinct types doped with tungsten, tin, chromium, and carbon, fabricated by Known Inc. A comprehensive characterization was performed by subjecting the devices to sinusoidal excitations with varying frequencies and amplitudes, followed by data averaging and high-frequency filtering. The resulting measurements were fitted using three prominent memristor models: VTEAM, MMS, and Yakopcic, with additional bespoke modifications assessed. These models, typically formulated as coupled algebraic-differential equations integrating electrical quantities (voltage and current) with internal state variables governing device dynamics, were optimized using two robust approaches: (1) interior-point optimization with gradient-based search, and (2) Nelder-Mead gradient-free optimization, both with box constraints applied. A thorough comparison and discussion of the optimized model parameters ensued, accompanied by an examination of sensitivity to diverse frequency and amplitude ranges. The findings inform conclusions and provide a foundation for future refinements, underscoring the importance of multi-model evaluation and advanced optimization strategies in precise memristor modeling. The presented methodology offers a valuable framework for elucidating optimal modeling paradigms tailored to specific memristor architectures and operating regimes, ultimately enhancing their integration in emerging neuromorphic and computational applications.

Wafer-scale blue micro-light-emitting diode (micro-LED) arrays are fabricated with a pixel size of 12 μm, a pixel pitch of 15 μm, and a pixel density of 1692 pixels per inch, achieved by optimizing the properties of e-beam-deposited and sputter-deposited indium tin oxide (ITO). Although the sputter-deposited ITO (S-ITO) films exhibit a densely packed morphology and lower resistivity compared to those of the e-beam-deposited ITO (E-ITO) films, the forward voltage (VF) values of a micro-LED with the S-ITO films are higher than those with the E-ITO films. The VF values for a single pixel and for four pixels with E-ITO films are 2.82 V and 2.83 V, respectively, while the corresponding values for S-ITO films are 3.50 V and 3.52 V. This was attributed to ion bombardment damage and nitrogen vacancies in the p-GaN layer. Surprisingly, the VF variations of a single pixel and of four pixels with the optimized E-ITO spreading layer from five different regions are only 0.09 V and 0.10 V, respectively. This extremely uniform VF variation is suitable for realizing micro-LED displays to be used in AR and VR applications, circumventing the bottleneck in the development of long-lifespan and high-brightness organic LED devices for industrial mass production.

Background: In most cases, intra-labyrinthine schwannoma (ILS) occurs in patients with unilateral hearing deterioration or neurofibromatosis type II (NF II). The pattern of localization of these tumors is various but affects mostly the cochlea. Extirpation of the ILS, if hidden by the cochlea modiolus, is difficult under the aspect of complete removal. Therefore, a tissue removal device (TRD) was designed and tested in temporal bones. The principle of handling the new device is a pushing and pipe cleaner handling inside the cochlea. This present study aimed to describe the first in vivo experience with the newly developed TRD for removing cochlear intra-labyrinthine schwannoma. Methods: In three patients, the TRD was used for the tumor removal of ILS. In two patients with a cochlear schwannoma in combination with a cochlea implantation and one patient suffering from NF II, a cochlear schwannoma was removed with the TRD. The access was performed with a posterior tympanotomy, an enlarged round window approach, and an additional second-turn access. The device was inserted and extracted gradually from the second turn access until the rings were visible in the second turn access. By pushing and pipe cleaner handling, the tumors were removed. An MRI control was performed on the day postoperatively with a T1 GAD sequence. Results: Tumor removal with the TRD was performed in a 15-minute procedure. MRI control confirmed a complete removal on the postoperative day in both cases. Conclusion: In vivo handling of the device confirmed a straightforward handling for tumor removal. MRI scanning showed a complete removal of the tumor by the TRD.

The Semiconductor and Liquid Assisted Photothermal Effect (SLAPE)” concept was employed for the first time in this study to generate electricity from sunlight. In SLAPE process, a semiconducting material is immersed completely in a stable organic solvent to capture the complete sunlight reaching the earth surface and to turn it into the heat-energy that can be eventually converted into electricity by using Organic Rankine Cycle (ORC) with the help of a heat engine and electric generator. In this investigation, the SLAPE solar panels were fabricated with two top and bottom chambers separated by thin thermally conducting metal sheet (Cu or Al). Multi-crystalline silicon photovoltaic cells (SPVCs) in conjunction with -butyrolactone were employed to capture the sunlight, and a low-boiling point dichloromethane (DCM) solvent was employed as a working fluid to capture the in situ generated heat energy from sunlight. Upon exposure to the natural sunlight, the 21 numbers of SPVCs together with about 2 litres -butyrolactone containing one square meter area SLAPE solar panel has generated about 17 V when integrated with a laboratory model reciprocally moved steam engine and a custom-made electric generator, whereas, a commercial SPVC solar panel with 21 number SPVCs generate a maximum voltage of 11 V. The theoretical background governing the SLAPE solar panels, the necessity for their invention and the proof of concept of SLAPE solar panels have been thoroughly presented and discussed and established in this article.

Compton cameras detect scattered gamma rays and estimate the distribution of gamma-ray sources. Nonetheless, crafting a camera tailored to a specific application presents formidable challenges, often necessitating the implementation of diverse image reconstruction techniques. Delving into the factors influencing these cameras can pave the way for design optimization and performance enhancement. This study introduces an inventive detector design for Compton imaging systems, building upon the achievements of prior designs. The proposed system contains eight scatterer detectors and a semiconductor absorber detector, spaced at 1 mm and 30 mm intervals, respectively. The source-to-first-scatterer-detector distance is 5 mm, with scatterer and absorber detector plates measuring 70× 70× 2.125 mm³ and 70× 70× 10 mm³, respectively. Geant4 simulation toolkit models the Compton imaging system, and an analytical method reconstructs Compton camera images. Unlike more straightforward techniques, the analytical method directly reconstructs Compton camera images by solving the equation relating to the reflected image data. This approach is implemented in the C++ programming language. The study's findings reveal that the analytical method discerns optimal conditions and parameters that significantly influence efficiency, yielding a full width at half maximum (FWHM) of 3.7 mm with an angular uncertainty of approximately 2.7 degrees at an energy level of 0.662 MeV. Compared to another experimental design employing the analytical image reconstruction approach, the FWHM value decreased by 0.7 mm. This study presents an innovative detector design and an analytical reconstruction method for Compton imaging systems, showcasing improved efficiency and accuracy.

Among the various types of gas sensors, the chemoresistive gas sensors based on metal oxides are considered the most attractive ones due to their simple operation, low costs and miniaturization. Thin films of V2O5 undoped and doped with TiO2 were studied as nitrogen dioxide, methane and hydrogen sensors. The experimental kinetics of the electrical conductivity changes due to introduction and removal of gas on metal oxide gas sensors were successfully explained in terms of the Langmuir adsorption theory.

Although mammography has been the gold standard for early detection of breast cancer, if a woman has dense breast tissue, a false negative diagnosis may occur. Breast ultrasound, whether hand-held or automated, is a useful adjunct to mammography but adds extra time and cost. The primary aim was to demonstrate that our second-generation Aceso system, which combines full-field digital mammography (FFDM) and automated breast ultrasound (ABUS) in a single platform, is able to produce improved quality images that provide clinically meaningful results. Aceso was first tested using two industry standards: a CDMAM phantom to assess the FFDM images; and the CIRS 054GS phantom to evaluate the ABUS images. In addition, 25 women participated in a clinical trial: 14 were healthy volunteers while 11 were patients referred by the breast clinic at Groote Schuur Hospital. The CDMAM phantom results showed the FFDM results were better than EUREF’s standard of “acceptable” and were approaching “achievable”. The ABUS results showed lateral and axial spatial resolution of 0.5 mm and adequate depth penetration of 80 mm. Our second-generation Aceso system, with its improved quality of clinical FFDM and ABUS images, has demonstrated its potential for early detection of breast cancer in a busy clinic.

Abstract: High power semiconductor laser is a kind of photoelectric device with high efficiency and high stability, the performance of its drive system directly affects its output characteristics and service life. In order to solve the problems of stability and robustness of the output power of semiconductor laser, a semiconductor laser driving power supply with high efficiency, low ripple and strong anti-interference ability was developed. The power supply adopts full-bridge LCC resonant power topology. Firstly, a mathematical model is established to analyze the relationship between LCC resonator parameters and output current gain. Secondly, a LCC resonator parameter design method is proposed to reduce the current stress of components, and the variable frequency phase shift (PFM-PWM) composite control strategy and linear active disturbance rejection control (LADRC) algorithm are proposed, which not only ensures the zero voltage (ZVS) conduction of MOS tube, but also reduces the on-off loss of MOS tube. Improved power efficiency and suppressed output current ripple; At the same time, the instability of the output current is ensured due to the input voltage, load and parasitic parameter change of the circuit. Finally, the simulation and experimental results show that the power supply can be continuously adjustable in the output current range of 0-40A, the current ripple is less than 0.8%, and the working efficiency is up to 92%. It has the characteristics of high stability, small ripple, high efficiency, low cost and good robustness.

The prevalence of antiviral drugs (AVTs) has seen a substantial increase in response to the COVID-19 pandemic, leading to heightened concentrations of these pharmaceuticals in wastewater systems. The hydrophilic nature of AVTs has been identified as a significant factor contributing to the low degradation efficiency observed in wastewater treatment plants. This characteristic often necessitates the implementation of additional treatment steps to achieve complete degradation of AVTs. Semiconductor-based photocatalysis has garnered considerable attention due to its promising potential in achieving efficient degradation rates and subsequent mineralization of pollutants, leveraging the inexhaustible energy of sunlight. However, in recent years, there have been few comprehensive reports that have thoroughly summarized and analyzed the application of photocatalysis for the removal of AVTs. This review commences by summarizing the types and occurrence of AVTs. Furthermore, it places a significant emphasis on delivering a comprehensive summary and analysis of the characteristics pertaining to the photocatalytic elimination of AVTs. Ultimately, the review sheds light on the identified research gaps and key concerns, offering invaluable insights to steer future investigations in this field.

Cardiac amyloidosis is caused by amyloid fibrils that deposit in the myocardial interstitium, causing restrictive cardiomyopathy and eventually death. The electromechanical, inflammatory, and autonomic changes due to amyloid deposition result in arrhythmias. Atrial fibrillation is by far the most common arrhythmia. Rate control strategy is generally poorly tolerated due to restrictive filling physiology and heart rate dependance, favoring adoption of rhythm control strategy. Anticoagulation for stroke prophylaxis is warranted irrespective of CHA2DS2Vasc score in patients with favorable bleeding profile; data on left appendage closure devices is still insufficient. Ventricular arrhythmias are also not uncommon and the role of implantable cardioverter-defibrillator in cardiac amyloidosis is controversial. There is no evidence of improvement in outcomes when used for primary prevention in these patients. Bradyarrhythmia is most commonly associated with sudden cardiac death in cardiac amyloidosis. Pacemaker implantation can help provide symptomatic relief but does not confer mortality benefit.

The manuscript deals with a new two-parameter unit stochastic distribution, obtained by transforming the Gumbel distribution, using generalized logistic mapping, into a unit interval. The distribution thus obtained is called the Gumbel–Logistic Unit (abbr. GLU) distribution, and its key stochastic properties have been investigated in detail. Among others, it is shown that the GLU distribution, unlike the Gumbel one which is always positively asymmetric, can take both asymmetric forms. Also, the procedure for estimating parameters based on quantiles, along with the asymptotic properties of the obtained estimators and the study of their numerical simulation, is presented. Finally, the application of the GLU distribution in modeling some real–world data related to telecommunications is considered.

Objective: This study aimed to demonstrate the availability of portable devices for nasal FeNO measurement, which could replace exhaled NO measurement based on the continuous aspiration of multiple flow measurement systems. Methods: A descriptive cross-sectional study. The healthy subjects without rhinosinusis disorders (control group) and those with diagnosed allergic rhinitis (AR group) were enrolled in the study. They underwent nasal and bronchial FeNO measurements by both fixed flow NObreath® connected to nasal mask and multiple flows HypAir FeNO®. Results: A total of 153 people were recruited including 63 healthy subjects and 90 subjects with AR. There were no statistically significant differences in anthropometric characteristics between the two groups (P > 0.05). There were a significant increase in FeNO values in the AR group compared to the control group; concentrations of nasal and bronchial FeNO mearsured by NObreath® were 76.0 ± 50.7 ppb (vs 36.0 ± 28.1 ppb, P < 0.01) and 32.3 ± 15.4 ppb (vs 9.2 ± 5.6 ppb, P < 0.001), and those mearsured by NObreath® Hypair FeNO® were 1796.9 ± 523.3 ppb (vs 400.2 ± 123.1 ppb, P < 0.001) and 37.3 ± 23.0 ppb (vs 17.4 ± 18.3 ppb, P < 0.01). A weak correlation between the values measured by NObreath® and Hypair FeNO® devices was observed (r = 0.023 and r = 0.089, respectively; p < 0.05). Conclusions: The handheld NObreath® device is effective in measuring FeNO concentrations in both normal subjects and AR patients. The advantages in price and size, creating a compact, low-cost device that is convenient for use and research.

In this paper, single and repetitive frequency UIS characteristics of 1200 V asymmetric (AT)and double trench silicon carbide (DT-SiC) metal–oxide-semiconductor field-effect transistors (MOSFETs) under different working conditions are investigated by experiment and simulation. For asymmetric trench SiC MOSFETs, the failure mode is all thermal runaway under working conditions. However, the failure mode of double trench SiC MOSFETs mostly is gate oxide rupture, which indicates an instable avalanche robustness under UIS stress. The variations of measured parameters are recorded to evaluate typical electrical features of device failure. Furthermore, TCAD simulation is used to reveal the electro-thermal stress inside the device during avalanche. Additionally, failed devices are decapsulated to verify the location of failure point from the perspective of the semiconductor die. Finally, a new type of stepped-oxide vertical power DT MOSFET with P-type shielding and current spread layers is proposed for improvement of gate dielectric reliability.

This paper presents a novel framework for Collaborative Learning Networks (CLNs) in classrooms, aiming to optimize resource utilization and enhance educational services. The study addresses the inefficiencies of traditional education models, particularly the underutilization of computational resources and limited access to specialized software. The proposed framework employs a mix of task-based and random allocation strategies to distribute computational tasks within the CLN, considering each device’s capabilities and task requirements. The findings show significant improvement in resource utilization, facilitated by device-to-device collaboration and task sharing, thus enriching students’ learning experiences. This work contributes to optimizing resource utilization in education, advancing the field of CLNs.

Dopaminergic replacement therapy remains the mainstay of symptomatic treatment for Parkinson’s disease (PD), but many unmet needs and gaps remain. Device based treatments or device-aided non-oral therapies are typically used in the advanced stages of PD, ranging from stereotactic deep brain stimulation to levodopa or apomorphine infusion therapies but there are concerns due to a number of procedural, hardware, or long-term treatment-related side effects of these treatments, and limited nonmotor benefit in PD. Therefore, there is an urgent unmet need for low risk adjuvants or standalone therapies which can address the range of burdensome motor and nonmotor symptoms that occur in PD. Recent studies suggest that non-invasive neurostimulation of the vestibular system may be able to address these gaps with stimulation of the vestibular brainstem sensory network which extensively innervates brain regions regulating both motor and a range of nonmotor functions. Therapeutic non-invasive vestibular stimulation is a relatively modern concept that may potentially improve a broad range of motor and nonmotor symptoms of PD, even at early stages of the disease. Here we review previous studies supporting the therapeutic potential of vestibular stimulation for the treatment of PD and discuss ongoing clinical trials and potential areas for future investigations.

Vertical III-V semiconductor nanowires have shown promising absorption of light for solar cell and photodetector applications. The absorption properties can be tuned through the choice of III-V materials and geometry of the nanowires. Here, we review recent progress in the design of the absorption properties of both individual nanowires and nanowire arrays. Future directions for the research field are proposed.

With metal oxide semiconductors being a promising candidate for accurate indoor air quality assessments, multiple drawbacks of the gas sensors prevent their widespread use. Examples include poor selectivity, instability over time, and sensor poisoning. Complex calibration methods and advanced operation modes can solve some of those drawbacks. However, this leads to long calibration times, which are unsuitable for mass production. In recent years, multiple attempts to solve calibration transfer have been made with the help of direct standardization, orthogonal signal correction, and many more methods. Besides those, a new promising approach is transfer learning from deep learning. This article will compare different calibration transfer methods, including direct standardization, piecewise direct standardization, transfer learning for deep learning models, and global model building. The machine learning methods to calibrate the initial models for calibration transfer are feature extraction, selection, and regression (established methods) and a custom convolutional neural network TCOCNN. It is shown that transfer learning can outperform the other calibration transfer methods regarding the root mean squared error, especially if the initial model is built with multiple sensors. It was possible to reduce the number of calibration samples by up to 99.3 % (from 10 days to approximately 2 hours) and still achieve an RMSE for acetone of around 18 ppb (15 ppb with extended individual calibration) if six different sensors were used for building the initial model. Furthermore, it was shown that the other calibration transfer methods (direct standardization and piecewise direct standardization) also work reasonably well for both machine learning approaches, primarily when multiple sensors are used for the initial model.

The problems of modeling the human bladder and its stress-strain state under external static influence were considered. A method for identification of the anisotropic biomechanical characteristics of bladder tissue was proposed. A FEM model was created, which accepts into regard that the bladder is surrounded by fiber and affected by surrounding organs, and partially protected by pelvic bones. The model considered the presence of constant hydrostatic pressure on the walls of the bladder when it is full. It has been shown that isotropic mechanical characteristics of biological tissue can be used for studying the deformed state of a filled bladder if the filled bladder 300 ml is considered as initial non-deformed stage. This was shown by modeling and verification the effect of the external static force on the bladder. Numerical experiments were conducted based on the constructed model. To validate the results obtained, a series of natural experiments on the effect of external pressure on the bladder under ultrasound control was conducted. In the future, it is planned to use the constructed model to study rupture deformations of the bladder under the influence of static and dynamic loads.

This work is the first part of a series of papers on a comprehensive analysis of the processes of prebiotic self-organization and protophotosynthesis on the surface of semiconductor minerals and in systems of natural dispersed semiconductors. Comprehensive analysis within the framework of the "semiconductor world" concept allows integrating a variety of models on a single physical basis - from ZnS world and FeS world (based on inorganic semiconductors) to the PAH world and aromatic world (including organic semiconductors). Thus, we do not put forward a new alternative hypothesis of chemical evolution - a new "chemical world", but only integrate the evolutionary and geochemical criteria of different "chemical worlds" into a single "physical world", which gives one the opportunity to reconstruct and predict the directions of chemical evolution according to the uniform principles of physical chemistry. In the first part of this series we consider photoinduced self-organization and "photo-controlled" evolution of the early protobiological systems performing solar energy conversion on the surface of dispersed semiconductor minerals capable of (photo)catalyzing and photosensitizing prebiological processes. The latter include a transition from the elementary cycles of photocatalytic reactions on the surface of semiconductors to protophotometabolic cycles and protophotosynthesis, from photophysical processes on the surface of mineral semiconductors to photoinduced membrane potentials, from photocontrolled sorption on the surface of such minerals to the formation of photosensitive protomembranes and selection of photosynthetic structures. The evolutionary approach to the analysis of protobiological mechanisms and protobioenergetics within the framework of the "semiconductor world" concept provides a new approach to the study of the last common point of divergence of protobiological systems, where the emergence principles of different energy supply schemes (like the energy source-specific photoautotrophy and substrate-specific chemoautotrophy) merge at the physicochemical level. The proposed integrating scheme is consistent with most biological, geological, and physicochemical concepts, which ensures its complete cross-checking and internal consistency.

Power converter technologies have become increasingly vital in various applications due to their efficient management of electrical energy. With the growing prominence of renewable energy sources like solar and wind, the high penetration of power electronic converters has been justified. However, ensuring power quality has emerged as a significant challenge for grid-connected power converters. The divergence from the ideal sinusoidal waveform in terms of magnitude and frequency impacts both grid-side currents and voltages. Several studies have proposed solutions to address power quality issues at the load side. The advancement of power converters has been fueled by the development of high-performance microprocessors and the emergence of high-speed switching devices, such as SiC-MOSFETs. This paper focuses on the design of voltage source converters, particularly those based on SiC-MOSFET semiconductor devices. The article presents the design of H-Bridge cells, discusses two-level voltage source converters based on cascade H-Bridge cells in parallel configuration with experimental fault analysis, addresses the seven-level voltage source converters topology, and explores the design and experimental results of the matrix converter. The findings underscore the importance of considering the entire converter design for improved performance at high switching frequencies. The article concludes by summarizing the main outcomes and implications of this research.

Hetero-nanomaterials constructed by plasmonic metals and functional semiconductors show enormous potential in photocatalytic applications, such as water splitting, hydrogen production, CO₂ reduction, pollutants treatment. Their photocatalytic performances can be better regulated through adjusting structure, ingredient, and components arrangement. Therefore, the reasonable design and synthesis of metal/semiconductor hetero-nanostructures is of vital significance. In this article, we briefly review the recent progress in efficiently establishing metal/semiconductor nanomaterials for improved photocatalysis. The defined photocatalysts mainly include traditional binary hybrids, ternary multi-metals/semiconductor and metal/multi-semiconductors heterojunctions. The underlying physical mechanism for the improved photocatalytic activity of the established photocatalysts are highlighted. At the end of this article, a brief summary and possible future perspectives for further development in this field are demonstrated.

Various factors and constraints should be considered when developing a manufacturing production schedule, and such a schedule is often based on rules. This paper develops a composite dispatching rule based on heuristic rules that comprehensively consider various factors in a semiconductor production line. The composite rule is obtained by exploring various states of a semiconductor production line (machine status, queue size, etc.), where such indicators as makespan and equipment efficiency are used to judge performance. A model of the response surface, as a function of key variables, is then developed to find the optimized parameters of a composite rule for various production states. Further, dynamic scheduling of semiconductor manufacturing is studied based on support vector regression (SVR). This approach dynamically obtains a composite dispatching rule (i.e. parameters of the composite dispatching rule) that can be used to optimize production performance according to real-time production line state. Following optimization, the proposed dynamic scheduling approach is tested in a real semiconductor production line to validate the effectiveness of the proposed composite rule set.

Mitral regurgitation (MR) is a broadly diffuse valvular heart disease (VHD) with a significant impact on healthcare system and patient’s prognosis. Transcatheter mitral valve interventions (TMVI) are now well-established techniques included in the therapeutic armamentarium for managing patients with mitral regurgitation, either primary or functional MR. Even if guidelines give indications regarding the correct management of this VHD, the wide heterogeneity of patient’s clinical background, valvular and heart’s anatomy make each patient a unique case, in which the appropriate device’s selection requires a multimodality imaging evaluation and a multidisciplinary discussion. Proper pre-procedural evaluation plays a pivotal role to judge the feasibility of TMVI, as well as a cooperative works between imagers and interventionalist is crucial for procedural success. This manuscript aims to provide an exhaustive overview of the main parameters that need to be evaluated for appropriate device selection, pre-procedural planning, intraprocedural guidance and post-operative assessment in the setting of TMVI. In addition, it tries to give some insights about next perspective of structural cardiovascular imaging.

This study analyses regional development in one of the poorest provinces in China, Guizhou Province, between 2000 and 2012 using a multiscale and multi-mechanism framework. In general, regional inequality has been declining since 2000. In addition, economic development in Guizhou Province presented spatial agglomeration and club convergence, which shows how the development pattern of one core area, two-wing areas and a contiguous area at the edge of the province have been developed between 2006 and 2012. Multilevel regression analysis revealed that industrialization and investment level were the primary driving forces of regional economic disparity in Guizhou Province. The influences of marketization and decentralization on regional economic disparity were relatively weak. Investment level reinforced regional economic disparity and the development of core-periphery structure in the province. However, investment level actually weakened the regional economic disparity in Guizhou Province when the variable of time was considered. In addition, both the topography and urban–rural differentiation were the two main reasons for forming a core-periphery structure in Guizhou Province.

A constant effort is made in the physical metallurgy of transformation induced plasticity (TRIP) steels. These are multiphase steels, whose mechanical behavior depends on the different phases present, the intrinsic strength of each phase, the work hardening of each constituent and the austenite to martensite transformation, among others. Hard and soft phases can be distinguished in these steels and both stress and strain are distributed between them. The objective of this work was to simulate the stress-strain behavior for two TRIP steels. Bouquerel’s model was modified to account for the initial martensite, a moderate hard austenite and adjustable strain hardening parameters. The austenite fraction that transforms into martensite was computed through an Olson and Cohen model. The Mecking-Kocks model was used to evaluate the increment in the dislocation density and the Rodriguez-Gutierrez model, to compute the hardening of martensite. Ferrite is considered a soft phase, martensite and bainite, hard phases and austenite, a phase with a moderate hardness. The routine was implemented in MATLAB, and results were compared with those obtained experimentally in a tension test of two TRIP steels of the same composition but different heat treatments, obtaining in both cases a good agreement for the stress-strain-curves.

Layered halide perovskites have emerged as a promising contender in solid-state lighting thanks to their tunable bandgap, high luminescence quantum yield, and high color purity. However, the fabrication of perovskite light-emitting devices in laboratories usually experiences low de-vice-to-device reproducibility since perovskite crystallization is highly sensitive to ambient condi-tions, such as humidity and temperature. Although device processing inside gloveboxes is primarily used to reduce the influence of oxygen and moisture, several extraneous variables, including gas-eous pollution traces and thermal fluctuations in the inert atmosphere or contaminations from re-sidual solvents confined in the enclosed environment, can destabilize the crystallization process and alter the properties of the emissive layers. Here, we examine different experimental set-ups for spin-coating deposition of layered perovskites in inert atmospheres and their influences on the formation of polycrystalline thin films. Our results demonstrate that fluctuations in the glovebox properties (concentrations of residual O2 and H2O or solvent traces), even in very short timescales, can negatively impact the consistency of the perovskite film formation, while thermal variation plays a relatively minor role in this phenomenon. Furthermore, careful storage of chemical species inside the workstation is critical for reproducing high-quality perovskite layers. Consequently, when applying our most controlled environment for perovskite deposition, the photoluminescence life-time of perovskite thin films shows a standard deviation of only 3%, whereas the reference set-up yields a 15% standard deviation. Regarding complete perovskite light-emitting diodes, the uncer-tainties in statistical luminance and EQE data are significantly reduced from 230% and 140% to 38% and 42%, respectively.

We develop an action principle for producing a single fluid, two-constituent system with dissipation in general relativity. The two constituents in the model are particles and entropy. The particle flux creation rate is taken to be zero, while the entropy creation rate is non-zero. Building on previous work, it is demonstrated that a new term (the proper time derivative of the matter space ``metric'') is required in the Lagrangian in order to produce terms typically associated with bulk and shear viscosity. Equations of motion, entropy creation rate, and energy-momentum-stress tensor are derived. Using an Onsager approach of identifying thermodynamic ``forces'' and ``fluxes'' a model is produced which delivers the same entropy creation rate as the standard, relativistic Navier-Stokes equations. This result is then contrasted with a model generated in the spirit of the action principle, which takes as its starting point a specific Lagrangian and then produces the equations of motion, entropy creation rate, and energy-momentum-stress tensor. Unlike the equations derived from Onsager reasoning, where the analogs of the bulk and shear viscosity coefficients are prescribed ``externally'', we find that the form of the coefficients in the second example are a direct result of the specified Lagrangian. Furthermore, the coefficients are shown to satisfy evolution equations along the fluid worldline; also a product of the specific Lagrangian.

This work presents a novel approach for the study of the movement of droplets on inclined surfaces under the influence of gravity and chemical heterogeneities. The developed numerical methodology uses data-driven modeling to extend the applicability limits of an analytically derived reduced-order model for the contact line velocity. More specifically, while the reduced-order model is able to capture the effects of the chemical heterogeneities to a satisfactory degree, it does not account for gravity. To alleviate this shortcoming, datasets generated from direct numerical simulations are used to train a data-driven model for the contact line velocity, which is based on the Fourier neural operator and corrects the reduced-order model predictions to match the reference solutions. This hybrid surrogate model, which comprises of both analytical and data-driven components, is then integrated in time to simulate the droplet movement, offering a speedup of five orders of magnitude compared to direct numerical simulations. The performance of this hybrid model is quantified and assessed in different wetting scenarios, by considering various inclination angles and values for the Bond number, demonstrating the accuracy of the predictions as long as the adopted parameters lie within the ranges considered in the training dataset.

Currently Single Board Computers (SBCs) are sufficiently powerful to run Real-Time Operating Systems (RTOSs) and applications with real-time attributes and requirements. SBCs serve as a foundation in Industrial Internet of Things (IIoT). The NXP Semiconductors produces a series of SBCs based on ARM-processors for a variety of industrial applications. The continuous increase in real-time data generated by IoT devices adds further research issues about the efficiency of such systems and applications. The purpose of this research was to investigate the timing performance of an NXP TWR-K70F120M device with μClinux OS on running concurrently tasks with real-time features and constraints. A custom-built multithreaded application with specific compute-intensive sorting and matrix operations was developed and applied to obtain measurements in specific timing metrics, including task’s execution time, threads waiting time, and response time, under different threads variations. The performance of this device was additionally benchmarked and validated against favorite platforms, a Raspberry Pi4 and BeagleBone AI SBCs. The experimental results showed that this device stands well both in terms of timing and efficiency metrics. Execution times were quite lower than the others, by approximately 56% in the case of two threads, and by 29% in the case of thirty-two threads configurations.

Soil and Water Assessment Tool (SWAT) was used to simulate five glacierized river basins that are global in coverage and vary in climate. The river basins included the Narayani (Nepal), Vakhsh (Central Asia), Rhone (Switzerland), Mendoza (Central Andes, Argentina), and Central Dry Andes (Chile) with a total area of 85,000 km2. A modified SWAT snow algorithm was applied in order to consider spatial variation of associated snow melt /accumulation by elevation band across each subbasin. In the previous studies, melt rates varied as a function of elevation resulting from an air temperature gradient while the snow parameters were constant throughout the entire basin. A major improvement of the new snow algorithm is separating the glaciers from seasonal snow based on their characteristics. Two SWAT snow algorithms were evaluated in simulation of monthly runoff from glaciered watershed: 1) the snow parameters are lumped (i.e. constant throughout the entire basin) and 2) the snow parameters are spatially variable based on elevation band-subbasin (i.e. modified snow algorithm). Applying the distributed SWAT snow algorithm improved the model performance in simulation of monthly runoff with snow-glacial regime, so that mean RSR decreased to 0.49 from 0.55 and NSE increased to 0.75 from 0.69. Improvement of model performance was negligible in simulation of monthly runoff from the basins with monsoon runoff regime.

The development of computational acoustics allows simulation of sound generation and propagation in complex environment. In particular, meshfree methods are widely used to solve acoustics problems through arbitrarily distributed field points and approximation smoothness flexibility. As a Lagrangian meshfree method, smoothed particle hydrodynamics (SPH) method reduce the difficulty in solving problems with deformable boundaries, complex topologies, or multiphase medium. The traditional SPH method has been applied in acoustic simulation. This study presents the corrective smoothed particle method (CSPM), which is a combination of SPH kernel estimate and Taylor series expansion. The CSPM is introduced as a Lagrangian approach to improve accuracy in solving acoustic wave equations in the time domain. Moreover, a boundary treatment technique based on the hybrid meshfree and finite difference time domain (FDTD) method is proposed to represent different acoustic boundaries with particles. To model sound propagation in pipes with different boundaries, soft, rigid, and absorbing boundary conditions are built with this technique. Numerical results show that the CSPM algorithm is consistent and demonstrates convergence with exact solutions. Main computational parameters are discussed, and different boundary conditions are validated to be effective for benchmark problems in computational acoustics.

Memory and emotion are highly vulnerable to psychiatric disorders like post-traumatic stress disorder (PTSD), which has been linked to serotonin (5-HT) metabolism disruptions. In fact, over 90% of the 5-HT precursor tryptophan (Trp) is metabolized via the Trp-kynurenine (KYN) meta-bolic pathway, producing a variety of bioactive molecules. The aadat (kat2) gene encodes mito-chondrial kynurenine aminotransferase (KAT) isotype 2, responsible for kynurenic acid (KYNA) production. Little is known about its role in behavior. In CRISPR/Cas9-induced aadat knockout (kat2−/−) mice, we examined the effects on emotion, memory, motor function, Trp and its metabolite levels, enzyme activities in the plasma and the urine of 8-week-old males compared to wild-type mice. Transgenic mice showed more depressive-like behaviors in the forced swim test, but not in the tail suspension, anxiety, or memory tests. They also had fewer center field and corner entries, shorter walking distances, and fewer jumping counts in the open field test. Plasma metabolite levels are generally consistent with those of urine: KYN, antioxidant KYNs, 5-hydroxyindolacetic acid, and indole-3-acetic acid levels are lower; enzyme activities in KATs, kynureninase, and monoamine oxidase/aldehyde dehydrogenase are lower, but kynurenine 3-monooxygenase is higher; and ox-idative stress and excitotoxicity indices are higher. Transgenic mice show depression-like behavior in a learned helplessness model, emotional indifference, and motor deficits, coupled with a decrease in KYNA, a shift of Trp metabolism toward the KYN-3-HK pathway, and a partial decrease in the gut microbial Trp-indole pathway metabolite. This is the first evidence that deleting the aadat gene causes depression-like behaviors that are unique to despair experience, which appears to be linked to excitatory neurotoxic and oxidative stresses. This may lead to the development of a double-hit preclinical model in experience-based depression, better understanding of these complex condi-tions, and more effective therapeutic strategies by elucidating the relationship between Trp me-tabolism and PTSD pathogenesis.

A comprehensive modeling framework for the thermoforming of polymer matrix woven laminate composite was developed. Two numerical indicators, the slip path length and traction magnitude, have been identified to be positively correlated to matrix smearing and wrinkling defects. The material model has been calibrated with picture-frame experimental results, and the prediction accuracy for intra-ply shear and thickness distribution were examined with measurements on the physically formed parts. Finally, a parametric study was conducted to determine the relationship between various process parameters and the quality of the formed part. For the trapezoidal part, orienting the laminate at 45-degrees to the mold axis reduces the likelihood of matrix smear and wrinkling defects. Although this laminate orientation yielded a greater spatial variation of part thickness, the thickness deviation is lower than that for the 0-degree orientation case. Higher forming rates were found to result in more defects due to increased slip path lengths and traction magnitudes. Optimal forming speeds should balance rapid shaping within the operating temperature window while avoiding tear. It was discovered that shallower molds benefit from faster ramp rates, while deeper molds require slower rates to manage extensive shearing, stretching, and bending. Faster forming rates lead to smaller thickness increases at high intra-ply shear regions, indicating a shift from intra-ply shear to out-of-plane bending due to the visco-plastic effect of the molten laminate, and can negatively impact part quality. Lastly, it was shown that a well-conceived strategy using darts could improve the part quality by reducing the magnitude of the defect indicators.