In the process of sewage coagulation treatment, quartz sand is often used as a heavy medium to accelerate the settling rate of flocs, but it will adversely affect the removal efficiency of pollutants. The factors that affect the coagulation effect and can be controlled manually include the quartz sand dosage, coagulant dosage, sewage pH, stirring time, settling time, etc, their reasonable setting is critical to. This paper was to study the optimal conditions of quartz sand enhanced coagulation(QSEC), first, single-factor tests were conducted to preliminarily explore the optimal range of influencing factors, and then response surface methodology（RSM）tests were performed to accurately determine the optimums of significant factors. The results showed that the addition of quartz sand can’t improve the water quality of coagulation treatment, but it can significantly accelerate the coagulation settlement process, the quartz sand dosage, the coagulant dosage and sewage pH all impacted significantly on its coagulation effect, and existed inflection points. A model that could guide QSEC was obtained by RSM tests. The model optimization and experimental validation showed that the optimal QSEC conditions for treating domestic sewage were as follows: the polyaluminum chloride(PAC) dosage, cationic polyacrylamide(CPAM) dosage, the sewage pH, quartz sand dosage, stirring time and settling time were 0.97 g·L-1, 2.25 mg·L-1, 7.22, 2 g·L-1, 5 minutes and 30 minutes, respectively, and the turbidity of treated sewage was reduced to 1.15 NTU.

Alkaline and alkaline-thermal activation were used in an attempt to synthesize zeolites using the sedimented illite fraction of raw Devonian clays from the Kuprava clay pit in Latvia. The Si/Al molar ratio of these clays is 2.79. Thermal and hydrothermal treatments were conducted using 6M and 10M NaOH solutions, along with different curing environments. The treated samples were analyzed using XRD, FTIR, and SEM, and were compared to the raw and calcined illite fraction samples. The main phase that forms after alkaline treatment is hydrosodalite (Na8[AlSiO₄]₆(OH)₂∙2H₂O). Using a higher concentration of NaOH leads to a significant increase in hydrosodalite formation. Increasing the curing temperature from 120°C to 600°C slightly reduces hydrosodalite formation due to the crystallization of the nepheline (Na₃K(Al₄Si₄O₁₆)) phase. This phase forms relatively intensively when the chemically treated samples are cured in a nitrogen environment at 600°C, thereby reducing the formation of hydrosodalite. The characteristic layered-fused structure of clay minerals remains in all chemically treated samples when cured at 600°C in air, but it does not remain when cured at the same temperature in nitrogen. The intensive formation of hydrosodalite is mainly achieved through hydrothermal treatment, along with a primary treatment using 10M NaOH. Considering the calculated size of the crystallites, treatment with 6M NaOH and curing at 120°C can also be seen as beneficial for hydrosodalite formation.

The Chikungunya virus (CHIKV) poses a significant global public health concern, especially in Africa. Since its first isolation in Tanzania in 1953, CHIKV has caused recurrent outbreaks, challenging healthcare systems in low-resource settings. Recent outbreaks in Africa highlight the dynamic nature of CHIKV transmission and the challenges of underreporting and underdiagnosis. Here, we review literature and analyze publicly available cases, outbreaks, and genomic data providing insights into the epidemiology, genetic diversity, and transmission dynamics of CHIKV in Africa. Our analyses reveal the circulation of geographically distinct CHIKV genotypes, with certain regions experiencing a disproportionate burden of disease. Phylogenetic analysis of sporadic outbreaks in West Africa suggests repeated emergence of the virus through enzootic spillover, which is markedly different from inferred transmission dynamics in East Africa, where the virus is often introduced from Asian outbreaks, including the recent reintroduction of the Indian Ocean lineage from the Indian subcontinent to east Africa. Furthermore, there is limited evidence of viral movement between these two regions. Understanding the history and transmission dynamics of outbreaks is crucial for public health planning. Despite advances in surveillance and research, diagnostic and surveillance challenges persist. This review and secondary analysis highlight the importance of ongoing surveillance, research, and collaboration to mitigate the burden of CHIKV in Africa and improve public health outcomes.

This study was designed for the first time to improve phenolic yield and antioxidant activity of ultrasonic-assisted extraction from Acer truncatum leaves (ATL) using response surface methodology, and phenolic composition in ATL extracted under the optimized condition were characterized by UPLC-QTOF-MS/MS. Solvent and extraction time were selected based on preliminary experiments, and a four-factors-three-levels central composite design was conducted to optimize solvent concentration (X₁), material-to-liquid ratio (X₂), ultrasonic temperature (X₃) and power (X₄) for an optimal total phenol yield (Y₁) and DPPH• antioxidant activity (Y₂). The results showed that the optimal combination was ethanol: water (v:v) 66.21%, material-to-liquid ratio 1:15.31 g/mL, ultrasonic temperature 60 °C, power 267.30 W, and time 30 min with three extractions, giving a maximal total phenol yield of 7593.62 mg gallic acid equivalent /100 g d.w. and a maximal DPPH• antioxidant activity of 74241.61 μmol Trolox equivalent/100 g d.w.. Furthermore, 22 phenolics were first identified in ATL extract obtained under the optimized conditions, indicating that gallates, gallotannins, quercetin, myricetin and chlorogenic acid derivatives were the main phenolic composition in ATL. What’s more, a gallotannins pathway existing in ATL from gallic acid to penta-O-galloyl-glucoside was interpreted. All these results provided practical information aiming at full utilization of phenolics in ATL, together with fundamental knowledge for further research.

A highly efficient reduction process of Cr (VI) with biochar was conducted in this paper. The results showed that nearly 100% Cr (VI) was reduced at selected reaction conditions: the dosage of biochar at m (C)/m(Cr) = 3.0, reaction temperature of 90 ℃, reaction time at 60 min and concentration of H2SO4 of 20 g/L, respectively. The reduction kinetics analysis demonstrated that the reduction of Cr (VI) fitted well with the pseudo-first-order model and the apparent activation energy was calculated to 40.24 kJ/mol. Response surface methodology confirmed that all the experimental parameters had positive effect on the reduction of Cr (VI). The influence of each parameter on the reduction process followed the order: dosage of biochar> Concentration of H2SO4 > Reaction Temperature > Reaction Time. This paper provided a versatile strategy for treatment of wastewater containing Cr (VI) and showed a bright tomorrow for wastewater treatment.

Automated controlling the harvesting systems can significantly increase the efficiency of the agricultural practices and prevent food wastes. Modeling and improvement of the combine harvester can increase the overall performance. Machine learning methods provide the opportunity of advanced modeling for accurate prediction of the highest performance of the machine. In this study, the modeling of combine harvesting id performed using radial basis function (RBF) and the hybrid machine learning method of adaptive neuro-fuzzy inference system (ANFIS) to predict various variables of the combine harvester for the optimal performance. Response surface methodology (RSM) is also used to optimize the models. The comparative study shows that the ANFIS method outperforms the RBF method.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

The research improves the strength of plastic using avocado seed starch and PLA. The effect of blending avocado seed starch and PLA was optimized using the RSM approach by using two variables: water absorption and biodegradability. Mixing them using RSM gave the best result: 1.8 g of starch and 3 g of PLA. Degradable plastic has a (tensile strength of 10.1 MPa; elongation at break of 85.8%; young modulus of 190 MPa). Infrared spectroscopy showed that the plastic had a -OH bond at 3273.20 cm-1, 3502.73 cm-1, 3647.39 cm-1, a CH2 bond at 2953.52 cm-1, 2945.30 cm-1, 2902.87 cm-1, a C=C bond at 1631.78 cm-1, and a C-O bond at 1741.72 cm-1. The plastic decomposed in soil. It was organic and hydrophilic. Thermal tests, the plastic can withstand heat well, losing weight at 356.86°C to 413.64°C, forming crystals and plastic melts at 159.10°C—the same as PLA. Melt flow test, sample melts before measurement, therefore not measurable—process conditions that affect. Water absorption of 5.763% and biodegradation rate of 37.988% decomposed for 12 days. In morphology analysis, the starch and PLA fused to form a smooth surface. RSM found value was close to 1. RSM gave the best process parameters.

The multi-objective optimization design of hydraulic climbing mechanism (the core mechanism of gantry crane) was realized by using the method of combining central composite design (CCD), Kriging and multi-objective genetic algorithm (MOGA). Firstly, the hydraulic climbing mechanism model was established and the appropriate design variables were selected. The mass, maximum deformation and maximum equivalent stress of the hydraulic climbing mechanism was taken as the optimization objectives. Through the comparative analysis of the parameters of wedge block, anchor block, anchor plate、baffle, the parameters that have the greatest impact on the optimization objectives are selected as geometric constraints. Then, according to the results of experimental design, Kriging model was used to establish the response surface optimization model of objective function. Finally, the optimal results were obtained by using MOGA method. The experimental results show that the optimization strategy is reliable, and the mass of the optimized model is reduced by 10.28%. While meeting the actual production requirements, the lightweight design of the hydraulic climbing mechanism is realized, which saves the design cost and improves the material utilization rate.

The overall cost of a hydropower plant is mainly due to the expenses for civil works, mechanical equipment (turbine and control units) and electrical components. The goal of a new draft tube design is to obtain a geometry that reduces investment costs, especially the excavation ones, but the primary driver is to increase the overall machine efficiency allowing for reduced payback time. In the present study, an optimization study of the elbow-draft tube assembly of a Kaplan turbine was conducted. A CFD model for the complete turbine has been developed and validated; next, an optimization of the draft tube alone was performed using a Design of Experiments technique; finally, several optimum solutions for the draft tube were obtained using a Response Surface technique aiming at maximizing pressure recovery and minimizing flow losses. A selection of optimized geometries was subsequently post-checked using the validated model of the entire turbine and a detailed flow analysis on the obtained results could make it possible to provide insight into the improved designs. It was observed that efficiency could be improved by 1% (in relative terms), and the mechanical power increased by 1,8% (in relative terms) with respect to the baseline turbine.

Surface water plays a crucial role in climate change, human production, and life, making accurate monitoring and observation of surface water particularly important. However, due to the significant diversity and complexity of water distribution in surface space, accurate mapping of surface water faces considerable challenges. When extracting water bodies from medium-resolution satellite remote sensing images, CNN methods may suffer from limitations in receptive fields and insufficient context modeling capabilities, leading to the loss of water body boundary details and poor fusion of multiscale features. Currently, there is relatively little research on this issue; therefore, it is necessary to explore new combinations of deep learning networks to address these challenges. The purpose of this study is to address the above issues. We propose a new combination of deep learning networks that fully utilize multiscale information to enhance water features. Specifically, we first combine deformable convolutions with the Swin Transformer to increase effective receptive fields while better integrating global semantic information. This combination can capture features of water bodies at different scales, improve the accuracy and integrity of water extraction, and provide reliable technical support for detailed water body extraction. We tested the newly constructed model using Sentinel-2 satellite images. Our model achieved results of over 90%, with an average accuracy of 97.89%, average precision of 94.98%, average recall of 90.05%, and an average F1 score of 92.33%. In addition, our model achieved an accuracy of 98.03% in mountainous areas. Our experiments and results validate the potential of combining the Swin Transformer and deformable convolutions in detailed water body extraction.

The major challenge in the current context of a rising world’s energy demand is to limit the global temperature increase for mitigating climate change. This goal requires a large reduction of CO2 emissions, mainly produced by power generation and industrial processes using fossil fuels. In this study, a novel methodology for K2CO3-doped Li4SiO4 sorbents production for CO2 capture at high temperature was adopted based on the Design of Experiments (DoE). Different synthesis (temperature and K2CO3 content) and adsorption conditions (sorption temperature and CO2 concentration) were systematically tested by Response Surface Methodology (RSM) to obtain predictive models of CO2 uptake and Li4SiO4 conversion. The results of RSM analysis evidenced a maximum adsorption capacity of 196.4 mg/g for a sorbent produced at 600 °C and with 36.9 wt% of K2CO3, tested at 500 °C and 4 vol% of CO2. Whereas at 50 vol% of CO2, the best uptake of 295.6 mg/g was obtained with a sorbent synthesized at 600 °C, containing less K2CO3 (17.1 wt%) and tested at higher temperature (662 °C). The obtained results highlight that K2CO3-doped Li4SiO4 sorbents can be tailored for maximizing CO2 capture at different operating conditions, making them suitable for use in industrial processes.

The present study employed a modifed QuEChERS method to systematically analyze the presence of fifteen Quinolones and seven Tetracyclines antibiotic residues in local animal food. Additionally, a multi-level-four-factor Box-Behnken design (BBD) within the framework of Response surface methodology (RSM) was utilized to evaluate the various factors affecting the detection efficiency of the sample pretreament procedure. The optimization was performed by Design Expert®, the factors including volume of the acetonitrle, the addition of formic acid, the duration of extract and the addition of EDTA were combined to experiment design until reach an optimal solution. Finally, the sample test was conducted by ultra-high performance liquid chromatography-quadrupole-linear ion trap mass spectrometry in both multiple reaction monitoring (MRM) and enhanced product ion (EPI) scan modes on a QTRAP® 5500 instrument. The overall average recoveries from actual samples fortified with 22 antibiotics at three levels ranged from 74.7 to 122.6% based on the use of matrix-fortified calibration with the variation ranging from 2.1 to 18.2% (n=6). The limits of detection and quantification were 0.3 μg kg-1 and 1.0 μg kg-1, respectively.

Organic Coatings have potential applications in the prevention of metal corrosion in an aqueous solution. The protective effect of SEBS coated copper corrosion in NaCl 3% solution was investigated by using electrochemical methods. The main objective of this work is to find the optimal conditions of the protocol immersion to evaluate the effects of SEBS ratio and two-immersion time on the anticorrosive behaviour of copper in 3 wt % NaCl solution in order to determine the best conditions to produce a protective SEBS film on the copper surface. Response Surface Methodology (RSM) is used as an optimization method. The study’s findings show the combination of three environmental factors that minimize corrosion rate. The Box-Behnken Design (BBD) is working perfectly for the statistical significance of the model (ANOVA test). This analysis calculates the contribution value of each parameter in changing the value of the corrosion rate (CR) in not only individual but also synergistic cases. The optimized parameters were found to be a 2.17% of SEBS ratio, 20 min of immersion 1, and 21 min of immersion 2. The electrochemical impedance spectroscopy tests confirmed the results.

In this study, the optimal condition for the extraction of antioxidants from the fruit Buah Mahkota Dewa (Phaleria macrocarpa) was determined by using Response Surface Methodology (RSM). The optimization was applied using central composite design (CCD) to investigate the three independent variables, namely extraction temperature (^oC), extraction time (minutes) and extraction solvent to-feed ratio (%v/v) on the responses of free radical scavenging activity (DPPH), ferric ion reducing power assay (FRAP), total phenolic content (TPC) and total flavonoid content (TFC).The optimal conditions for the antioxidants extraction were found to be extraction temperature (64^oC), extraction time (66 minutes) and solvent to-feed ratio (75 %v/v) with the highest percentage yield of DPPH, FRAP, TPC and TFC were 86.85%, 7.47%, 292.86 mg/g and 3.22 mg/g respectively. Moreover, the data were subjected to response surface methodology (RSM) and the results showed that the polynomial equations for all models were significant, did not show lack of fit, and presented adjusted determination coefficients (R²) above 99%, proving the yield of phenolic, flavonoid and antioxidants activities obtained experimentally were close to the predicted values and the suitability of the model employed in RSM to optimize the extraction conditions. Hence, in this study, the fruit from P.macrocarpa could be considered to have the strong antioxidant ability and can be used in various cosmeceutical or medicinal applications.

In this data deposit, I describe a dataset that is the result of content mining 167,318 published articles for statistical test results. As a result of this content mining, 688,112 results from 50,845 articles were extracted. In order to provide a comprehensive set of data, the statistical results are supplemented with metadata from the article they originate from. The dataset is provided in a comma separated file (CSV) in long-format. For each of the 688,112 results, 20 variables are included, of which seven are article metadata and 13 pertain to the individual statistical results (e.g., reported and recalculated p-value). A five-pronged approach was taken to generate the dataset: (i) collect journal lists, (ii) spider journal pages for articles, (iii) download articles, (iv) add article metadata, and (v) mine articles for statistical results.

There is a growing demand for clean-label products. This study aimed to obtain a food-grade coloring ingredient for meat products based on the formation of Zn-protoporphyrin from porcine livers, thus contributing to the development of nitrite-free products. First, the effects of sodium disulfite, and acetic, ascorbic, and lactic acids on Zn-protoporphyrin formation and total microbial count were studied. The combination of ascorbic and acetic acid resulted in a higher Zn-protoporphyrin content than acetic acid alone and maintained microbial levels (ca. 3 log CFU/mL). Second, a response surface methodology was used to maximize Zn-protoporphyrin while maintaining microbiological food standards. The effects of pH (4.2–5.4), incubation time (3–30 h), and temperature (25–50 ºC) were studied. The selected conditions for Zn-protoporphyrin formation involved anaerobic incubation at pH 4.8 and 45 °C for 24 h. The safety was validated through challenge testing for relevant pathogens (Listeria monocytogenes, Salmonella spp., and Clostridium perfringens). A significant reduction (> 6 log units) was observed for L. monocytogenes and Salmonella, whereas C. perfringens spores remained at inoculated levels. The optimized procedure is proven to be microbiologically safe, and it is proposed to improve the color of nitrite-free meat products.

Friction stir welding (FSW) is a solid state welding process for joining metallic alloys and dissimilar metals. It has emerged as an alternative technology for welding high strength alloys that are difficult to join with conventional techniques. FSW is used to produce products with better mechanical properties. Now a days aluminum alloys have been widely used in several industrial applications such as aerospace, marine, automobile and commercial applications due to their light weight structure, better mechanical properties and high corrosion resistance.In this work, three welding parameters such as spindle speed, welding speed and plunge depth were considered for friction stir welding. FSW was carried out between dissimilar aluminum alloy plates (AA6061 and AA 8011) to produce butt joint.A Box-Behnken design with three factors and three levels was chosen to minimize the number of experimental conditions .The tensile strength and hardness of the welded regions were evaluated. The optimum level settings and the major parameters that influence the joint strength were obtained by Box-Behnken design.

Polyurethanes are materials with a strong structure-property relationship. The goal of this research was to study the effect of a polyol blend composition of polyurethanes on its properties using a mixture design and setting mathematic models for each property. Water absorption, hydrolytic degradation, contact angle, tensile stretch, hardness and modulus were studied. Additionally, Thermal stability was studied by thermogravimetric analysis. Area under the curve was used to evaluate the effect of polyol blend composition on thermal stability and kinetics of water absorption and hydrolytic degradation. Least squares were used to calculate the regression coefficients. Models for the properties were significant, and lack of fit was not (P<0.05). Fit statistics suggest both good fitting and prediction. Water absorption, hydrolytic degradation and contact angle were mediated by the hydrophilic nature of the polyols. Tensile strength, modulus and hardness could be regulated by the molecular weight and hydroxyl index of the polyols. Regression of DTG curves from thermal analysis showed improvement of thermal stability with the increase of PCL and PE. An ANOVA test of the model terms demonstrated that three component effects on bulk properties like water absorption, hydrolytic degradation, hardness, tensile strength and modulus, and the PEG*PCL interaction with the contact angle, which is a surface property. Mixture design application allowed for an understanding of the structure-property relationship through mathematic models.

Brushless Direct Current Motors are significantly improved for using many electrical applications. The design investigation is increased year by year and most of the motor design researchers find out the superior efficiency of the BLDC motor. The traditional motor consumed more electrical power than BLDC motor. The design of BLDC motors that are compact, small, easy to control, save energy and light weight. Due to this fact, the design of BLDC motor should be analyzed to improve the motor characteristics performance. The research focuses on the design of BLDC motor performance using Taguchi Method and Response Surface Methodology (RSM) for Finite Element Method (FEM). Firstly, the Taguchi Method is applied to identify the optimization point of design parameters and consider using the reference model of actual BLDC electric fan motor with a rated power of 26Watts design. Based on the Taguchi Method to create the RSM is used to two-step optimization design performance using in FEM analysis. The performances of motor design proposed approach to provide the effeteness for motor design investigator. In this investigation aims the better structural performances in output power, torque, efficiency and torque ripple. The final design of proposed model achieved an energy efficiency is 10% higher than the reference design of prototype modes, the output power result is 10W higher this reference design. We can reduce the loss of the proposed motor design. Furthermore, the maximum torque can also increase the 0.032Nm of that design. The design simulation results were produced and studied by the FEM analysis of JMAG software. From the evaluation results, the configurations of reference model design are compared with the proposed design by using the three methods of motor design optimization showed the best characteristics for performance of motor investigation design.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Questionnaires for self-report of food-elicited emotions are an established practice in consumer studies. However, most tools are originally developed in English and translated into other languages, which limits their use. The aim of this study was to develop the first Greek emotion lexicon and measurement tool for consumers, using standard methodology and extending it. The lexicon was compiled using linguistic sources and extended using the World Wide Web and a popular social media platform for the collection of authentic language and usage data. Terms were also collected from consumers using questionnaires and a variety of stimuli. Terms collected from consumers only comprise: healthy, distrustful, curious, childish, impressed, tolerant, impatient It was validated by application in various case studies, providing discrimination across and within food categories, and by comparison to the Greek translation of a standard tool in English, the EsSense Profile. The comparison was conducted by measuring emotions elicited by six food categories and demonstrated that it is preferable to use emotion measurement tools developed in the linguistic and cultural context of intended use, as they convey consumers’ emotions naturally and more accurately. This tool can be used as a Check- or Rate- All-That-Apply questionnaire to measure consumer responses to food categories and products. The methodology and validation presented can be applied for the compilation of emotion lexicons in languages less studied than English.

Human serum albumin (HSA) corona formation at polymer microparticles of a spheroidal shape was studied using dynamic light scattering and laser Doppler velocimetry (LDV). Physicochemical characteristics of the albumin comprising, the zeta potential and the isoelectric point were determined as a function of pH for various ionic strengths. Analogous characteristics of the polymer particles were carried out. The adsorption of albumin on the particles was monitored by electrophoretic mobility measurements (LDV). The stability of the HSA functionalized particle suspensions under various pHs and their electrokinetic properties were determined. The deposition kinetics of the particles on mica, silica and gold sensors were determined in situ by optical microscopy, AFM and by the quartz microbalance (QCM) under diffusion and flow conditions. The obtained results were interpreted in terms of the coarse-grained random sequential adsorption model that allowed to estimate the range of applicability of QCM for determining deposition kinetics of virus and bacteria at abiotic surfaces.

In this study, we applied a central composite design to estimate independent variables and establish optimal conditions of filtration rate and feces production that enhance filtration of suspended organic matter by the freshwater mussels Sinanodonta woodiana. The results indicated that statistical design methodology offers an efficient and feasible approach for high filtration and low feces production condition optimization. The proposed model equation takes into account the quantitative effect of variables and also the influence of interactions among variables on mussel filtration rate. Under the optimal experimental conditions (mussel size, 13.0 ± 0.2 cm; water current, 17.5 L/h), the experimental filtration rate of 4.47 ± 1.82 L/mussel/h showed a degree of correspondence with the predicted value of 8.4 L/mussel/h, which verified the practicability of this optimum strategy.

The article presents the stages of modeling and simulation of a new design of a wheelchair with the option of moving up and down stairs. These analyzes were aimed at the synthesis of the de-sign parameters and parameters of the sensor and control systems. The simulation results were verified by experimentally testing the prototype.

Peptides, both natural and synthetic, are well suited for a wide range of purposes and offer versa-tile applications in different fields such as biocatalysts, injectable hydrogels, tumor treatment, and drug delivery. The rising prominence of therapeutic peptides encompasses anticancer, antiviral, antimicrobial, and anti-neurodegenerative properties. The metals Na, K, Mg, Ca, Fe, Mn, Co, Cu, Zn, and Mo are ten of the twenty elements that are considered essential for life. Crucial for under-standing the biological role of metals is the exploration of metal-bound proteins and peptides. Aside from essential metals, there are other, non-essential metals that also interact biologically, exhibiting either therapeutic or toxic effects. Irregularities in metal binding contribute to diseases like Alzheimer’s, neurodegenerative disorders, Wilson's, and Menkes disease. Certain metal com-plexes have potential applications as radiopharmaceuticals. The examination of these complexes was done by preforming UV-Vis, IR, EPR, NMR spectroscopy, and X-ray analysis.

The depletion and environmental problems associated with fossil fuels have encouraged us to look for alternative feedstock that do not compromise food security and the environment. Sorghum is a fast-growing crop that can be harvested twice a year and produces both food and straw that can be utilized in the production of bio-based fuels. In this study, the production of bioethanol and the effects of fermentation parameters on ethanol yield are presented. A sequential pretreatment method was employed, using dilute sulfuric acid (1%) at 125 °C in the first stage and dilute sodium hydroxide (1.25 %) at 90 °C in the second stage. The residues left after the sequential pretreatment stage were hydrolyzed using acid hydrolysis. The sugar concentration of the hydrolysates was determined using the phenol sulfuric acid method, and three hydrolysates having sugar levels of 30.42 g/L, 31.79 g/L, and 32.9875 g/L were selected for fermentation. The ethanol yield was determined after 72 hours of fermentation at 30 °C with varying inoculum sizes (5%, 10%, and 15%) and pH (4.5, 5, and 5.5). With a maximum ethanol yield of 0.617 mL/g (48.742%) produced at a sugar content of 32.9875 g/L, pH of 5, and inoculum size of 15%, statistical analysis showed that all three independent parameters affected ethanol yield. According to these findings, while raising sugar content, inoculum amount, and pH all initially result in higher ethanol yields, doing so further reduces yield. So, in order to increase ethanol yield, fermentation conditions must be carefully managed while producing ethanol from sequential acidic-alkaline pretreated sorghum straw. The strategy followed by using sequential acidic-alkaline pretreatment of sorghum straw provides prospects for efficient and effective production of biofuels from alternative feedstock.

This paper focused on the finite element analysis of structural system in extreme loading condition. Two different stud shape and thicknesses were analyzed under blast. The stud thickness such as 1.19 mm and 1.5 mm were modelled and analyzed using ABAQUS 6.14. FEM is a tool which predicts the engineering physics of the real structure. To validate the finite element modelling performed by authors, a reference work published by earlier researchers on cold-formed steel stud wall is considered and examined in the present study. The novelty of this study was web corrugation and influence of flange width on stud. The models mimic like an air bag in a car to delay the pressure timing inside the stud wall. The mass of explosive used as 1.56 kg at a standard scaled distance. Time versus displacement was captured out at four locations in the stud wall. One of the objectives is to develop mathematical model to validate the deformation of stud under blast loading. Two mathematical models were validated using Artificial Neural Network (ANN). The results captured in ANN model was error histogram, regression plot, best performance fit and training data. The models were capable of resisting the moderate blast load. The response surface methodology (RSM) was employed to evaluate model performance Regression equations are useful for predicting future trends and outcomes, which is crucial for planning and decision-making. The primary goal of this work is to evaluate cold-formed steel stud walls with varying stud sizes under blast loading using finite element analysis and validated by ANN and RSM.

A sustainable low cost activated carbon substitute was produced based on pretreated lignocellulosic biomass, especially spruce sawdust. A harmful liquid waste, desalination brine was used for the treatment of a solid wood industry waste, spruce sawdust. This approach is in the circular economy theory and aims to the decarbonization of the economy. The pretreated sawdust was tested as an adsorbent appropriate for the removal of a commonly used pollutant, methylene blue, from industrial wastewater. The adsorption capacity of the pretreated material was found to increased four times comparing to the untreated one in the case that the Freundlich equation was fitted to the isotherms’ data. The treatment experimental conditions with desalination brine that gave maximum adsorption capacity correspond to 1.97 combined severity factor in logarithmic form value. The same adsorption capacity was found to increase five to six times comparing to the untreated spruce sawdust in the case that the Langmuir isotherm model was applied at the same data. Moreover, kinetic experiment was cried out as regards the methylene blue adsorption process. The desalination brine pretreated sawdust adsorption capacity increased 1.4 times comparing to the untreated one, in the case of the Lagergren kinetic equation fitting. Furthermore, the adsorption capacity of the same material was increased 1.6 times when the second order kinetic model was applied to the same data. Industrial scale applications can be based on the kinetic data findings as they have to do with a very shorter adsorption period comparing to the isotherm data.

The process of preparing anti-glare thin films by spray-coating silica sol-gel to soda-lime glass was exclusively and statistically studied in this paper. The effects of sol-gel deliver pressure, air transport pressure, and spray gun displacement speed on the gloss, haze, arithmetic mean surface roughness, and total transmittance light were analyzed. The experimental results indicate that the factors of sol-gel deliver pressure, air transport pressure, and displacement speed exhibit significant effect on the haze, gloss, and Ra. In contrast, the variation of total transmittance light with these three factors are insignificant. Because the anti-glare property is predominantly determined by low gloss and high haze, therefore, we aim to minimize gloss and maximize haze to achieve high anti-glare. Central composite design and response rurface methodology are employed to analyze the main and interaction effects of the three factors through quadratic polynomial equations, which are confirmed by the analysis of variance and R². The response surface methodology predict the lowest gloss and highest haze are 9.2 GU and 57.0%, corresponding to the sol-gel deliver pressure, air-transport pressure, and displacement speed of 250 kPa, 560 kPa, and 140 mm/s, and 340 kPa, 620 kPa, and 20 mm/s, respectively. Comparing the predicted optimal data with the real experimental results validates the applicability of the mathematical model. This study provides an important basis for the subsequent production of anti-glare glass with different specifications to satisfy the market demand.

Large-scale crowd phenomena are complex to model because the behaviour of pedestrians needs to be described at both strategic, tactical, and operational levels and is impacted by the density of the crowd. Microscopic models manage to mimic the dynamics at low densities, whereas mesoscopic models achieve better performances in dense situations. This paper proposes and evaluates a novel agent-based architecture to enable agents to dynamically change their operational model based on local density. The ability to combine microscopic and mesoscopic models for multi-scale simulation is studied through a use case of pedestrians at the Festival of Lights, Lyon, France. Pedestrian outflow data is extracted from video recordings of exiting crowds at the festival. The hybrid model is calibrated and validated using a genetic algorithm that optimizes the match between simulated and observed outflow data. Additionally, a local sensitivity analysis is then conducted to identify the most sensitive parameters in the model. Finally, the performance of the hybrid model is compared to different models in terms of density map and computation time. The results demonstrate that the hybrid model has the capacity to effectively simulate pedestrians across varied density scenarios while optimizing computational performance compared to other models.

This study is dedicated to understanding and simulating the mechanical properties of concrete, with a specific focus on the mesoscopic scale. Investigating concrete at this level involves examining its composition as a heterogeneous amalgamation comprising mortar, aggregates, and the interfacial transition zone (ITZ). Such an approach provides a detailed examination of the material's behavior and attributes. Numerical models are utilized, leveraging the finite element method (FEM), to examine the behavior of concrete. The study employs MATLAB programming to develop three-dimensional models, subsequently subjected to FEM analysis. Various mesoscopic Representative Volume Elements (RVEs) are formulated, encompassing varied shapes and dimensions. The MATLAB framework generates input files for numerical FEM simulations, replicating compression strength tests. As complexity increases with the inclusion of the ITZ, prismatic RVEs are developed. The proposed mesoscopic model establishes a foundational framework for a numerical simulation methodology tailored to laboratory compression tests. It provides detailed insights into concrete behavior, elucidating deformation, and fracture mechanisms. Although not a complete substitute for experimental methods, these models offer a cost-effective and expeditious alternative, pinpointing vulnerable areas and exploring the implications of additional materials on concrete behavior. Experimental data and virtual tests pave the way for mitigating carbon footprint and improving concrete sustainability.

Reactions of quinones with compounds containing an amino group can produce a wide variety of addition or substitution products that depend on reactivity of both quinone and amino derivative. 6,7-Dichloropyrido[1,2-a]benzimidazole-8,9-diones undergo selective nucleophilic substitution reaction with different benzohydrazides and α-hydroxy-p-quinone imine derivatives stabilized by strong intramolecular hydrogen bond were isolated. Synthesized compounds represent a combination of several structural motifs: benzimidazole core fused with α-hydroxy-p-quinone imine which contains a benzamido fragment. The protonation/deprotonation processes were investigated in a solution using UV-Vis spectroscopy and 1H NMR titration experiment. X-ray crystallography analysis revealed a set of weak non-covalent interactions such as intra- and intermolecular hydrogen bonds and π-π stacking. Additionally, the redox behavior of 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione and its p-imino derivative was investigated in acidic and neutral environment using cyclic voltammetry measurements. Cathode material based on 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione could act as potential effective active electrode in aqueous electrolyte batteries, however further optimization is required.

In this work, two plasmonic structures with two different periodic nanostructures (nanodisk and nanostrip arrays) separated from the gold layer by an ultrathin dielectric Al2O3 layer are proposed, and their optical properties are simulated as 3-dimensional models using COMSOL Multiphysics software tool. The optical responses, such as the amplification of the electric field and the scattering, absorption and extinction cross sections of the two structures, are investigated and compared. The results show that both structures show strong field enhancement in their gap layer, and the structure with the periodic array of metal nanodisks shows stronger field enhancement and larger absorption, extinction, and scattering cross sections in its dipole resonance wavelength, which is defined as a bright plasmonic mode. In addition, some weaker resonant modes are observed for both structures and the reason for their generation is dis-cussed. The analysis of different possible modes in such structures is crucial for their application in various fields.

Efficient utilization of biomass requires conversion into forms that can be optimally applied in energy generation. Briquetting involves compaction of biomass into solid blocks that are more efficient than raw biomass and provides for ease of transport and handling. These are improved when the briquettes possess high shatter index and compressive strength. Due to difference in nature and composition, it is imperative to define optimum conditions for the production of quality and durable briquettes for individual biomass compacted into briquettes. This study studied the effects of process variables on the strength and durability of biomass briquettes produced using Abura sawdust. The lateral compressive strength and drop shatter index were investigated whilst varying the temperature (100-150 °C), pressure (9-15 MPa) and hold time (15-30 min). The compressive strength ranged between 2.06 and 5.15 MPa whilst the shatter index was between 50 and 600. The pressure was significant to the determination of the compressive strength (p &lt; 0.1) and the shatter index (p &lt; 0.05). Mechanical characteristics of the binderless Abura sawdust briquettes can be improved by optimizing the densification variables during the briquetting process when moderate pressures are used for compaction.

Large-scale hydrological modeling in China is challenging given the sparse meteorological stations and large uncertainties associated with atmospheric forcing data.Here we introduce the development and use of the China Meteorological Assimilation Driving Datasets for the SWAT model (CMADS) in the Heihe River Basin(HRB) for improving hydrologic modeling, by leveraging the datasets from the China Meteorological Administration Land Data Assimilation System (CLDAS)(including climate data from nearly 40000 area encryption stations, 2700 national automatic weather stations, FengYun (FY) 2 satellite and radar stations). CMADS uses the Space Time Multiscale Analysis System (STMAS) to fuse data based on ECWMF ambient field and ensure data accuracy. In addition, compared with CLDAS, CMADS includes relative humidity and climate data of varied resolutions to drive hydrological models such as the Soil and Water Assessment Tool (SWAT) model. Here, we compared climate data from CMADS, Climate Forecast System Reanalysis (CFSR) and traditional weather station (TWS) climate forcing data and evaluatedtheir applicability for driving large scale hydrologic modeling with SWAT. In general, CMADS has higher accuracy than CFRS when evaluated against observations at TWS; CMADS also provides spatially continuous climate field to drive distributed hydrologic models, which is an important advantage over TWS climate data, particular in regions with sparse weather stations. Therefore, SWAT model simulations driven with CMADS and TWS achieved similar performances in terms of monthly and daily stream flow simulations, and both of them outperformed CFRS. For example, for the three hydrological stations (Ying Luoxia, Qilian Mountain, and ZhaMasheke) in the HRB at the monthly and daily Nash-Sutcliffe efficiency ranges of 0.75-0.95 and 0.58-0.78, respectively, which are much higher than corresponding efficiency statistics achieved with CFSR (monthly: 0.32-0.49 and daily: 0.26 – 0.45). The CMADS dataset is available free of charge and is expected to a valuable addition to the existing climate reanalysis datasets for deriving distributed hydrologic modeling in China and other countries in East Asia.

Heavy metals pollution in the Straits of Malacca warrants the development of rapid, simple and sensitive assays. Enzyme-based assays are excellent preliminary screening tool with near real-time potential. The heavy-metal assay based on the protease ficin was optimized for mercury detection using Response Surface Methodology. The inhibitive assay is based on ficin action on the substrate casein and residual casein is determined using the Coomassie dye-binding assay. Heavy metals strongly inhibit the hydrolysis. A Central Composite Design (CCD) was utilized to optimize detection. The results show a marked improvement for the concentration causing 50% inhibition (IC50) for mercury, silver and copper. Compared to One-factor-at-a-time (OFAT) optimization, RSM gave an improvement of IC50 from 0.060 (95% CI, 0.0300.080) to 0.017 (95% CI, 0.0160.019), from 0.098 (95% CI, 0.0770.127) to 0.028 (95% CI, 0.0220.037) and from 0.040 (95% CI, 0.035.045) to 0.023 (95% CI, 0.0200.027), for mercury, silver and copper, respectively. A near real-time monitoring of mercury concentration in the Straits of Malacca at one location in Port Klang was carried out over a 4-h interval for a total of 24 h and validated by instrumental analysis with the result revealing an absence of mercury pollution in the sampling site.

The study presents a comparative approach between response surface methodology (RSM) and hybridized, genetic algorithm artificial neural network (GA-ANN) in predicting the water absorption, compressive strength, flexural strength split tensile strength and slump for steel fiber reinforced concrete. The effect of process variables such as aspect ratio, water cement ratio and cement content were investigated using the central composite design of response surface methodology. This same experimental design was used in training the hybrid-training approach of artificial neural network. The predicting ability of both methodologies were compared using the root mean sqaured error (RMSE), mean absolute error (MAE), model predictive error (MPE) and absolute average deviation (AAD). The RSM model was found more accurate in prediction compared to hybrid GA-ANN.

In this study, we investigated the effects of three surface treatment techniques on 316L stainless steel, low-temperature immersion corrosion, shot peening followed by immersion corrosion, and electrochemical corrosion. Surface alterations were analyzed using scanning electron microscopy, Raman spectroscopy, and α-step thin-film thickness profiling. Human osteoblast adhesion was evaluated using Liu’s stain and metallographic optical microscopy. The results revealed weak cell adhesion after low-temperature immersion and shot peening followed by immersion corrosion. By contrast, electrochemical corrosion, particularly with a high current density and low corrosive solution concentration, resulted in a uniformly corroded surface, thus promoting dense cell adhesion. All three techniques resulted in porous oxide layers. Overall, our experimental findings highlighted shot peening (1 kg/cm2 for 20 s) and electrochemical corrosion (0.5 M HCl) as effective processes. Electrochemical corrosion produced uniformly dense corrosion pits, whereas shot peening produced semicircular grooves with small corrosion pits, both favorable for cell adhesion. Electrochemical corrosion also yielded excellent cell adhesion, emphasizing its suitability for biomedical activity. We developed a process for creating a porous surface layer and thereby enhancing the cell adhesion to 316L stainless steel for potential biomedical implant applications.

Dietary polyphenols exist in two forms; extractable polyphenols (EPP) or compounds solubilised by aqueous/organic solvents, and non-extractable polyphenols (NEPP) or compounds remain in the corresponding residues after the extraction. At present, most researchers focus on EEP fractions, while NEPP is neglected. Thus, this study aimed to release NEPP from the remaining powder residue of Barhi date palm kernels (BDPK) with acid hydrolysis. The related extraction conditions were determined and optimised using response surface methodology (RSM) for maximisation of NEPP with highest cytotoxic and antioxidant activities. The face-centred central composite design (FCCCD) was used to establish treatments based on three independent variables, namely; extraction temperature, time, and solvent/sample ratio. Under the optimal conditions, the experimental values for DPPH radical-scavenging capacity of NEPP (IC50=57.52µg/mL), and cytotoxicity of NEPP against A549 and HT29 cells were IC50=17.4 µg/mL and 31.4µg/mL, respectively. The experimental values were in agreement with those predicted by RSM models, confirming the suitability of the model employed and the success of RSM for optimisation of the extraction conditions for NEPP from BDPK. These results indicate that NEPP from industrial date fruit waste could be a promising candidate as natural antioxidants with significant antiproliferation effect against A549 and HT29 cancer cells in-vitro.

Fungi play important roles in the process of material cycling and energy transfers in aquatic ecosystems. Yet little is known about the fungal community in lake sediment. In this study, sediment samples from five habitat types in Baiyangdian Lake (BYD Lake) were collected across three seasons. High-throughput sequencing techniques were used to determine the compositions of fungal communities. Fungi are highly diverse in the sediment of BYD Lake, although some important fungi have not been accurately identified. The fungal diversity was highest in winter and lowest in summer, while the variations of species richness among sampling sites were not significant. The compositions of fungal community differed among seasons and habitats. Physicochemical properties of sediments were measured and the influence of the environmental factors on fungal communities were analyzed. Temperature, P, N, and heavy metals explained 48.98% of the variations of fungal communities across three seasons. Human activities have affected the species and biomass of fungi to some extent. Temperature is the most influential factor and is negative to fungal diversity. Nutrient element in different forms have different effects on shaping the fungal community. The effect of heavy metals is not clear.

To accurately predict the matching relationships between the various components and the engine performance in the whole aero-engine environment, this study introduces a two-dimensional throughflow simulation method for the whole aero-engine. This method is based on individual throughflow solvers for the turbo-machinery and the combustor. It establishes a throughflow simulation model for the whole engine by integrating with the compressor-turbine co-operating equations and boundary conditions. The turbo-machinery throughflow solver employs a circumferentially averaged form of the time-dependent Navier-Stokes equations (N-S) as the governing equation. The combustor solver uses the Reynolds Average Navier-Stokes (RANS) method to solve flow and chemical reaction processes by constructing turbulence, combustion, and radiation models. The accuracy of the component solver is validated using Pratt &amp; Whitney’s three-stage axial compressor (P&amp;W3S1) and General Electric’s high-pressure turbine (GE-EEE HPT), and the predicted results are consistent with the experimental data. Finally, the developed throughflow method is applied to simulate the throttling characteristics of the WZ-X turboshaft engine. The results predicted by the throughflow program are consistent with the GasTurb calculations, including the trends of shaft power delivered, specific fuel consumption (SFC), inlet airflow, and total pressure ratio of the compressor. The developed method to perform throughflow simulation of the whole aero-engine eliminates the dependence on a general component map. It can quickly obtain the meridian flow field parameters and overall engine characteristics, which is expected to guide the design and modification of the engine in the future.

Polarimetry is used to determine the Stokes parameters of a laser beam. Once all four S0,1,2,3 parameters are determined, the state of polarisation is established. Upon reflection of a laser beam with the defined S polarisation state, the directly measured S parameters can be used to determine the optical properties of the surface, which modified the S-state upon reflection. Here, we demonstrate polarimetry for the determination of surface anisotropies related to birefringence and dichroism from different materials, which have a common feature of linear patterns of different alignments and scales. It is shown that polarimetry in the back-reflected light is complementary to ellipsometry and four-polarisation camera imaging.

Objective: The aim of this study was to optimize the fermentation process of Radix Ranunculi ternate via microbial fermentation and analyze the changes in the contents of the main components, the antioxidant and hypoglycemic capacities of the extract before and after fermentation. Methods: The solid-state fermentation process was optimized using single-factor tests and the response surface method, with the yield of the alcohol extract of R. ternate as an evaluation index. Results: The best fermentation process was optimized using solid-state endophytic fungus fermentation technology as follows: strain addition ratio of Chaetomium globosum/Fusarium equiseti =1:1, fermentation for 5 d, sieve size of 40 mesh, liquid/material ratio of 0.8:1 mL·g−1, fermentation temperature of 31 °C, and inoculation amount of 7.5%. Under the optimized conditions, the contents of the water-soluble extract and total polysaccharides decreased by 12.71% and 12.95%, respectively, in the fermentation, The contents of ethanol-soluble-extract, flavonoids, saponins, polyphenols, organic acids, and total amino acids of fermented R. ternate increased by 19.77%, 57.14%, 79.67%, 14.29%, 17.63% and 3.82%, respectively, and the scavenging rate for DPPH, ABTS+, ·OH free radicals and inhibitory rate for α-amylase also increased by 19.02%, 14.17%, 7.53% and 34.54%, respectively, compared with unfermented R. ternate. Conclusions: Solid-state fermentation opens new avenues for the development and application of R. ternate as natural antioxidant and hypoglycemic food.

The dynamic response of the shed-tunnel structure under rockfall impact attracts much attention in recent years. However, the research on the dynamic response of the shed-tunnel structure under rockfall impact mostly focuses on the rockfall single impact, while in practical engineering, the shed-tunnel structure often encounters the rockfall repeated impacts during its service life. Therefore, this research focuses on exploring the dynamic response characteristics of the shed-tunnel structure under the rockfall repeated impacts. First of all, based on the model test of the shed-tunnel under rockfall impact as a reference, the FEM (Finite Element Method)-SPH (Smoothed Particle Hydrodynamics) coupling numerical calculation model is established based on ANSYS/LS-DYNA finite element code. The numerical simulation of the dynamic response of the shed-tunnel structure under rockfall impact is realized, and the rationality of the model is verified. Then, with this model and the full restart technology of LS-DYNA code, the effects of four factors, e.g. rockfall mass, rockfall impact velocity, rockfall impact angle and rockfall shape, on the impact force and impact depth of the buffer layer, the maximum plastic strain and axial force of the rebar, the shed roof vertical displacement and the shed-tunnel plastic strain are studied. These results show that the cumulative deformation and damage of the shed-tunnel structure caused by the rockfall repeated impacts play an important role in the destruction of the shed-tunnel structure, and the special attention should be paid to this issue.

This article aims to serve as a guide for the construction of supply chain simulation models designed with a lean approach, using Promodel software. To achieve this, a supply chain was designed for a fictitious company located in the City of Celaya, Guanajuato and a set of suppliers located in different cities within the same State. It was used as a google tool to define the distances between each of the companies. As a final result, a representative model of a supply chain was obtained, as well as a methodology that allows the construction of lean supply chains regardless of the number of companies that comprise it. The effect of the variability in the delivery times between suppliers was incorporated into the simulation model, as well as an equation that calculates the pollution emissions of the vehicles that integrate the network that moves the products between the companies. With this work it is possible to represent networks of supply chains of real world companies, where the variability and contamination factor is included, to facilitate the decision making regarding the number of vehicles, inventory levels, quantities to be shipped, frequency in the shipments, etc. with the purpose of contaminating as little as possible and at the same time preventing interruptions in the supply chain using the least amount of resources possible.

In these last years, self-healing polymers have emerged as a topic of considerable interest owing to their capability to partially restore material properties and thereby extend the product's lifespan. The main purpose of this study is to investigate the nano-indentation response in terms of hardness, reduced modulus, contact depth and coefficient of friction of a self-healing resin developed for use in aeronautical and aerospace contexts. To achieve this, the bifunctional epoxy precursor underwent tailored functionalization to improve its toughness, facilitating effective compatibilization with a rubber phase dispersed within the host epoxy resin. This approach aimed to highlight the significant impact of the quantity and distribution of rubber domains within the resin on enhancing its mechanical properties. The main results are that pure resin exhibits a higher hardness (about 36.7% more) and reduced modulus (about 7% more), consequently leading to a lower contact depth and coefficient of friction (11.4% less) compared to other formulations that, conversely, are well-suited for preserving damage from mechanical stresses due to their capabilities in absorbing mechanical energy. Furthermore, finite element method (FEM) simulations of the nanoindentation process were conducted. The numerical results were meticulously compared with experimental data, demonstrating a good agreement. This validation of the FEM model underscores its efficacy in predicting the mechanical behavior of nanocomposite materials under nanoindentation. The proposed investigation aims to contribute knowledge and optimization tips about self-healing resins.

For marine vessels, a propeller shaft system, also known as a propulsion shaft system, is an essential changer in engine torque and propeller thrust. The propeller shaft system is subjected to transverse, longitudinal, and torsional excitations during operation. These sources of excitations originate from alternating thrust generated by the propeller, operation of a propeller in a stern flow field which is non-uniform in time and space, misalignment of components such as shafts, bearings, and keyholes in the assembly, excitations in the form of rotational motion, and the whirling motion of the shafts. These dynamic excitations posed a challenging issue for the integrity and reliability of a marine vehicle. Thus, it is crucial to analyze the dynamic response of the propulsion shaft system. The dynamic analysis of the propulsion shaft system is typically conducted using numerical /analytical models. At present, Finite Element Model (FEM) as a numerical model plays a vital role in analyzing the dynamic response of the structure. The computed response and the modal parameters from the FE model are reliable only if accurate boundary conditions, such as stiffness, can be imposed on the model. However, the numerical FE model deviates from the experimental results because of uncertainties in the stiffness values of the bearings and other connectors. This paper uses the Response Surface Optimization (RSO) technique to estimate the unknown stiffness of the bearings used in the propulsion shaft system. The experimental model of the propeller shaft system is constructed from the steady-state response of the system using the step sine excitation. The natural frequencies and the amplitude of vibrations in the FE model are updated using the parametric RSO technique. The updated model shows that the difference in natural frequencies and vibration amplitude is less than 10% between the optimized and experimental models. Propeller Shaft, Vibrations, Optimization, Response Surface

Crop production in Afghanistan suffers from limited phosphorus (P) availability, which severely hinders national agriculture sustainability. This present study hypothesized that deep fertilizer placement could significantly enhance uptake of immobile P and thus tissue P accumulation and crop yield. A two-year pot experiment growing two maize (Zea mays) hybrid cultivars (Xida-789 and Xida-211) was therefore conducted to test these hypotheses under three contrasting fertilizer placement methods (broadcast, side band, and deep band). In doing so, P concentrations in both maize tissues and soils were compared at 45, 60, and 115 days after sowing (DAS) under nine combinations of nitrogen (N) and P fertilizer rates (kg ha-1: N112P45, N112P60, N112P75, N150P45, N150P60, N150P75, N187P45, N187P60, N187P75). Results have shown that deep band placement significantly increased P uptake efficiency, leading to greater P concentration and accumulation in maize tissues compared to other two fertilization methods. This improved P uptake was attributed to several factors associated with deep placement, including reduced P fixation, enhanced root access to P, and moisture availability for P uptake. Additionally, deep band placement combined with higher N application rates (N187 and N150) further enhanced plant P uptake by promoting P availability and utilization mechanisms. Deep band placement also resulted in significantly higher total soil P, Olsen-P, and P use efficiency than broadcast and side band methods, indicating a more efficient P fertilization strategy for maize that can improve growth and yield. This present study also found positive correlations between P concentration in plant organs and soil Olsen-P, highlighting the importance of adequate soil P levels for optimal plant growth. Overall, our results have showed that deep band fertilizer placement emerged as a superior strategy for enhancing P uptake efficiency, utilization, and maize productivity compared to broadcast and side band placement. This approach can potentially optimize P fertilizer utilization, improve maize growth and yield, while minimizing environmental P losses associated with broadcast applications.

As urbanization continues to increase, key conservation areas like World Heritage sites are being altered. This transformation is a cause for concern as it threatens the Outstanding Universal Value of these sites. To address this issue, a research question was formulated: How urban is World Heritage? The research focused on identifying and monitoring urbanization in heritage core zones listed on the World Heritage by tracking changes in built-up areas from 1985 to 2015. The findings revealed that urban developments, including housing, transport infrastructure construction, visitor accommodation facilities, and land conversions, have significantly impacted heritage properties. More than a third (37\%, 426) of the cultural heritage properties reported urban development, with the highest occurrences in Europe, North America, Asia, and the Pacific. Furthermore, these regions also displayed the highest rate of change per year between 1985 and 2015. This indicates the urgent need to identify and monitor the urbanization of World Heritage to preserve their OUV amidst increasing urban development.

Density functional theory (DFT) calculations of hydrogen adsorption on titanium nitride had previously shown that hydrogen may adsorb on both titanium and nitrogen sites with a moderate adsorption energy. Further, the diffusion barrier was also found to be low. These findings may qualify TiN, a versatile multifunctional material with electronic conductivity, as electrode material for the hydrogen evolution reaction (HER). This was the main impetus of this work which aims to experimentally and theoretically investigate the electrocatalytic properties of TiN-layers that were processed on Ti substrate using reactive ion sputtering. The properties are discussed focusing on the role of oxygen defects introduced during the sputtering process on the HER. Based on DFT calculations, it is shown that these oxygen defects alter the electronic environment of the Ti atoms which entails a low hydrogen adsorption energy in the range of -0.1 eV; this leads to HER performances that match those of Pt-NPs in acidic media. When a few nanometr thick layer of Pd-NPs is sputtered on-top of the TiN-layer, the performance is drastically reduced. This is interpreted in terms of oxygen defects being scavenged by the Pd-NPs near the surface which is thought to reduce the hydrogen adsorption sites.

The effect of graphene (GR) on Ni surface relaxation and reconstruction in three different substrate orientations: {111}, {001}, {011}, at two different temperatures: 300K and 400K was studied using Molecular Dynamics simulation. The change of the interplanar distances of the substrate and redistribution of Ni and C atoms in direction perpendicular to the surface were compared with the equilibrium state of GR and bulk Ni, in the absence of the counterpart. The surface reconstruction for GR/Ni system was analyzed base on the calculated radial pair distribution function of Ni and C atoms. The surface roughness was visualized using 2D atomic distribution maps. For the studied substrate orientations and temperatures, it was found that the most densely packed orientation of the Ni base {111} provides minimal changes of the structural parameters of both counterparts at 400 K.

Laser machining by ultra-short (sub-ps) pulses at high intensity offers high precision, high throughput in terms of area or volume per unit time, and flexibility to adapt processing protocols to different materials on the same workpiece. Here we consider the challenge of optimization for high throughput: how to use the maximum available laser power and larger focal spots for larger ablation volumes by implementing a fast scan. This implies the use of high-intensity pulses approaching ∼PW/cm2 at the threshold where tunnelling ionization starts to contribute to overall ionization. A custom laser micromachining setup was developed and built to enable high speed, large area processing and easy system reconfiguration for different tasks. The main components include laser, stages, scanners, control system, and software. Machining of metals such as Cu, Al, or stainless steel, and fused silica surfaces at high-fluence and high-exposure doses at high scan speeds up to 3 m/s were tested for the fluence scaling of ablation volume, which was found to be linear. Modified surfaces are color-classified for their appearance, which is dependent on surface roughness and chemical modification. Such colour-coding can be used as a feedback parameter for industrial process control.

The study of the surface thermodynamic properties of solid materials is primordial for the determination of the dispersive surface energy, polar enthalpy of adsorption and Lewis’s acid base properties of solid particles. Inverse gas chromatography technique (IGC) at infinite dilution is the best surface technique for the determination of the surface physicochemical properties of materials. (1) Background: This paper was devoted to study the surface properties of solid materials such as alumina particles by using IGC technique. (2) Methods: Different methods and molecular models such as spherical, cylindrical, van der Waals, Redlich-Kwong, Kiselev and geometric models, were used to determine the London dispersive surface energy of solid surfaces. Hamieh model was also used and highlighted the thermal effect on the surface area of solvents. (3) Results: The variations of the dispersive surface energy and the free energy of adsorption were determined for alumina particles as a function of the temperature as well as their Lewis’s acid base constants. Alumina surfaces were proved to exhibit a strong Lewis amphoteric character three time more basic than acidic (4) Conclusions: The new methodology based on Hamieh model gave the more accurate results of the physicochemical properties of the particle surfaces.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

Conditions under which compositions of component systems form a well-defined system-of-systems here are formulated at a fundamental level. Statement of what defines a well-defined composition and sufficient conditions guaranteeing such a result offers insight into exemplars that can be found in special cases such as differential equation and discrete event systems. For any given global state of a composition, two requirements can be stated informally as: 1) the system can leave this state, i.e., there is at least one trajectory defined that starts from the state, and 2) the trajectory evolves over time without getting stuck at a point in time. Considered for every global state, these conditions determine whether the resultant is a well-defined system and if so, whether it is non-deterministic or deterministic. We formulate these questions within the framework of iterative specifications for mathematical system models that are shown to be behaviorally equivalent to the Discrete Event System Specification (DEVS) formalism. This formalization supports definitions and proofs of the afore-mentioned conditions. Implications are drawn at the fundamental level of existence where the emergence of a system from an assemblage of components can be characterized. We focus on systems with feedback coupling where existence and uniqueness of solutions is problematic.

A novel approach based on response surface methodology (RSM) was developed to predict and apply the best extraction conditions for the isolation of various-type polyphenolic antioxidants from the dried flower buds of Magnolia x soulangeana Soul.-Bod. var. ‘Lennei’ (Magnoliaceae). As a method of choice, ultrasound-assisted extraction was used and the optimized extraction parameters (temperature, time of extraction, the composition of aqueous-ethanolic extractants and solvent to solid ratio) have been determined using a central composite design factorial analysis, followed by appropriate spectrophotometric methods (with Folin–Ciocalteu and 2,2-diphenyl-1-picrylhydrazyl reagents) to determine the antioxidant and antiradical potential of extracts, respectively. The use of 66.8% (V/V) ethanol, as the extraction solvent during the 55.2 min extraction protocol, and the ratio of extractant volume to herbal substance of 46.8 mL/g gave the highest total yield of bioactive antioxidant phenolics in the extract obtained. For this herbal preparation, qualitative and quantitative analysis was performed using combined chromatographic (LC), spectroscopic (PDA) and tandem mass spectrometric (ESI-QTOF–MS/MS) techniques. A detailed phytochemical profiling, conducted for the first time, documented substantial amounts of polyphenolic antioxidants, especially phenylethanoids and flavonoids in the flower buds of M. soulangeana ‘Lennei’. Their average total content exceeded 30.3 and 36.5 mg/g dry weight, respectively.

In this paper an integrated methodology for the coupling between 1D- and 3D-CFD simulation codes is presented, which has been developed to support the design and calibration of new diesel engines. The aim of the proposed methodology is to couple 1D engine models, which may be available in the early-stage engine development phases, with 3D predictive combustion simulations, in order to obtain reliable estimates of engine performance and emissions for newly designed automotive diesel engines. The coupling procedure features simulations performed in 1D-CFD by means of GT-SUITE and in 3D-CFD by means of Converge, executed within a specifically designed calculation methodology. An assessment of the coupling procedure has been performed by comparing its results with experimental data acquired on an automotive Diesel engine, considering different working points including both part load and full load conditions. Different multiple injection schedules have been evaluated for part-load operation, including pre and post injections. The proposed methodology, featuring detailed 3D chemistry modeling, was proven to be capable to properly assess pollutant formation, specifically to estimate NOx concentrations. Soot formation trend was also well-matched for most of the explored working points. The proposed procedure can therefore be considered as a suitable methodology to support the design and calibration of new Diesel engines, thanks to its ability to provide reliable engine performance and emissions estimations from the early-stage of a new engine development.

Road pavement monitoring represents the baseline to the pavement maintenance process. To quickly fix a damaged road, relevant authorities need a high-efficiency methodology that allows them to obtain data describing the current conditions of a network of roads. In urban areas, large-scale monitoring campaigns may be more expensive and not fast enough to describe how pavement degradation has evolved over time. Furthermore, at low speeds, many technologies are inadequate for monitoring the streets. In such a context, employing black box equipped vehicles to perform a routine inspection could be an excellent starting point. However, the vibration-based methodologies used to detect road anomalies are strongly affected by the speed of these vehicles. In this study, a statistical method was to analyze the effects of speed on road pavement conditions at different severity levels through the data recorded by taxi vehicles. Likewise introduced was a process that overcomes the speed effect when considering road surface conditions. The methodology proposed has succeeded in predicting the right damage severity level based on only two recorded parameters: speed and pavement deterioration index.

Ocean surface waves have been utilized as fundamental information in various fields of oceanic research. In this paper, we suggest a simulation and modelling technique for generating an ocean surface wave using an inverse Fast Fourier Transform (iFFT), and we subsequently verify the wave’s accuracy. The conventional method, linear superposition, requires recursive calculation because of the double summation and the time variable; to circumvent this issue, the new algorithm is presented. The Joint North Sea Wave Project (JONSWAP) spectrum is utilized for the ocean surface wave simulation example, and the parameters are the significant wave height (HS) and the zero-crossing wave period (TZ). A coordinate transform for the wavenumber domain was used to apply the inverse FFT algorithm. To verify the accuracy of the simulation result, the relative error between the input condition and the analysis result was calculated. The result for TZ is below 4% relative error, and the maximum relative error for HS is 7%. To avoid the Nyquist frequency for wave-field analysis and simulation, the minimum grid size was calculated by twice applying the maximum wavenumber.

Many corporations have now revised their value statements to showcase their commitment to sustainable development and green business due to the pressing issues of climate and environmental damage. Despite the importance of value statements that can direct companies to achieve sustainable goals, what kind of values can be perceived as organizational orientations to sustainability remains unknown. This study explores how the general public views the inclusion of sustainable components in value statements from the listed companies in Hong Kong by using Q-sort methodology (n = 30). Analyzing the final sample of 40 value statements extracted from 27 listed companies, we identified three factors related to sustainability, namely, Empowering business process management, Empowering customer-centric excellence, and Empowering sustainable progress. This study provides an additional component to the traditional triple bottom line by suggesting that internal operation of a company is an emerging idea to understand corporate sustainability.

Due to the high computational burden and the high nonlinearity of the responses, crashworthiness optimizations are notoriously hard-to-solve challenges. Among various approaches, methods like the Successive Response Surface Method (SRSM) have stood out for their efficiency in enhancing baseline designs within a few iterations. However, these methods have limitations that restrict their application. Their minimum iterative resampling required is often computationally prohibitive. Furthermore, surrogate models are conventionally constructed using Polynomial Response Surface (PRS), a method that is poorly versatile, prone to overfitting, and incapable of quantifying uncertainty. Furthermore, the lack of continuity between successive response surfaces results in suboptimal predictions. This paper introduces the Multi-Fidelity Successive Response Surface (MF-SRS), a Gaussian process-based method, which leverages a nonlinear multi-fidelity approach for more accurate and efficient predictions compared to SRSM. After initial testing on synthetic problems, this method is applied to a real-world crashworthiness task: optimizing a bumper crossmember and crash box system. Results, benchmarked against SRSM and the Gaussian Process Successive Response Surface (GP-SRS) – a single-fidelity Gaussian process-driven extension of SRSM, show that MF-SRS offers distinct advantages. Specifically, it improves upon the specific energy absorbed optimum value achieved by SRSM by 14.1 %, revealing its potential for future applications.

This paper studies the optimization method of pump hydraulic performance based on the response surface method. A parametric model of impeller and diffuser is established. Three-dimensional optimization is carried out on the basis of the initial model obtained by one-dimensional design method. We select the pump hydraulic efficiency and the head as objective function and constraint function. Response surface models are constructed to analyze the relationship between the objectives and the design variables, and the global optimization of hydraulic performance is realized. According to the internal flow characteristics of pump, this paper proposes the strategy of two steps optimization, which aims at meridional plane and blade shape, respectively, to solve the problem of large numbers of design parameters and computational cost. The optimization results show that the hydraulic efficiency of pump increased by 3.7%, and the head is nearly the same.

As the energy efficiency demands for future buildings become increasingly stringent, preliminary assessments of energy consumption are mandatory. These are possible only through numerical simulations, whose reliability crucially depends on boundary conditions. We therefore investigate their role in numerical estimates for the usage of geothermal energy, performing annual simulations of transient heat transfer for a building employing a geothermal heat pump plant and energy piles. Starting from actual measurements, we solve the heat equations in 2D and 3D using COMSOL Multiphysics and IDA-ICE, and discover a negligible impact of the multiregional ground surface boundary conditions. Moreover, we verify that the thermal mass of the soil medium induces a small vertical temperature gradient on the piles surface. We also find a roughly constant temperature on each horizontal cross-section, with nearly identical values if the average temperature is integrated over the full plane or evaluated at one single point. Calculating the yearly heating need for an entire building we then show that the chosen upper boundary condition affects the energy balance dramatically. Using directly the pipes’ outlet temperature induces a 54% overestimation of the heat flux, while the exact ground surface temperature above the piles reduces the error to 0.03%.

In this paper, we studied the problem of early detection of natural phenomena associated with the formation of severe floods and the possibility of constant monitoring of their occurrence. The test object for the study was severe floods on the Crimean Peninsula, which occurred due to heavy rainfall in the summer of 2021. Based on the selected satellite and other data related to this period, an analysis carried out and key atmospheric objects identified, according to the proposed algorithm for their identification and grouping. Based on the results of the work, a positive conclusion made on the issue of their use to identify the likelihood of natural disasters that could lead to floods. In addition, the authors proposed to develop a portal for collecting and processing a large amount of satellite data related to flood prevention and monitoring the development of such processes, and stressed the need to create it.

This paper investigates an Energy Neutral System using Micro Energy Harvesters for a Health Monitoring Wireless Sensor Node (HM-WSN). We have implemented HM-WSN consisting of a solar cell energy harvester, a Power Management Unit (PMU) and the ucontroller, sensor and transmitter acting as load. A battery extender and a switching logic circuit for sensor node is designed to evaluate the efficiency of the proposed system. The HM-WSN senses body temperature with improvement in lifetime of coincell. The HM-WSN is built using commercially available off the shelf (COTS components and consumes 47.2uW for data being updated every 134s. It can be operated for approximately 1.32 years only on a coincell. Furthermore, the HM-WSN can be operated with solar energy at 200lux, achieving 96.36 years with a combination of a coincell with an additional capacitor of 2.2mF. It attains 4.07 years to 16.87 years lifetime with the load capacitor varying from 1mF to 1.5mF at 350lux lighting condition. With the same ambient condition and a 2mF load capacitor, HM-WSN attains complete energy autonomy.

The prevalence of diagnosed cases of autism has increased rapidly, which raise interest in studying the variables related to the well-being of these families. The purpose of this paper is to review recent literature on other variables related to family well-being such a parenting styles. We conducted a systematic review using PRISMA check list and bias assessment ESTROBE with the aim of analyzing if the concepts of autism, well-being and parenting style are related. We screened 753 references, 16 full text articles and abstracts were read. It was identified that authoritative parenting style, those based on warmth, establishing relationships and emotional bonding, and low expressed emotion were positively related to family well-being. On the other hand, authoritarian, permissive and overprotective styles, as well as critical, punishing and training-based were negatively associated with well-being and quality of family life.

Boiler efficiency is called to some extent of total thermal energy which can be recovered from the fuel. Boiler efficiency losses are due to four major factors: the dry gas flux, the latent heat of steam in the flue gas, the combustion loss or the loss of unburned fuel, radiation and convection losses. In this research, the thermal behavior of boilers in gas refinery facilities is studied and their efficiency and their losses are calculated. The main part of this research is comprised of analyzing the effect of various parameters on efficiency such as excess air, fuel moisture, air humidity, fuel and air temperature, the temperature of combustion gases, and thermal value of the fuel. Based on the obtained results, it is possible to analyze and make recommendations for optimizing boilers in the gas refinery complex using response-surface method (RSM).

The Storm Water Management Model (SWMM) was used to evaluate the impact of urbanization, climate change, and implementation of Low Impact Developments (LIDs) at the Mahabad Dam watershed, Iran. Several scenarios of urbanization, with and without climate change impacts, in different locations were defined, including near outlet, middle, far end, and whole watershed. Climate change was considered to change the intensity of rainfall and increase evaporation. Vegetative swales were implemented as LIDs to evaluate their applicability to reduce pollutant loads. Digital Elevation Model (DEM) of the area was input into ArcGIS, and the watershed was delineated using the ArcSWAT extension to identify topographic features. Water quality properties were defined in the software, and each scenario was run for a twelve-hour simulation. The results indicated that urbanization affects the imperviousness of sub-catchments, and location of urbanization affects the amount and timing of runoff and pollutant yields. Fifty-percent urbanization near the watershed outlet resulted in 23.1% and 27.4% increases in runoff and pollutant loads, respectively. Fifty-percent urbanization in the middle resulted in 28.8% and 35.4% increases in runoff and pollutant loads; and, at the far end, 23.1% and 3.9% increases in runoff and pollutant loads were the result; Fifty-percent urbanizing the whole watershed gave 58.6% and 66.3% increases in runoff and pollutant loads, respectively; Under climate change scenarios (higher intensity, shorter duration rainfall) peaks occurred earlier. Moreover, results showed LIDs decreased pollution loads up to 25%.

The unique structure of G4.0 PAMAM dendrimers allows the drug to be enclosed in internal spaces or immobilized on the surface. In the conducted research, the conditions for the formation of the active G4.0 PAMAM complex with doxorubicin (DOX) were optimized. The physicochemical properties of the system were monitored using DLS, CD, and fluorescence spectroscopy. The QCM-D method was chosen to determine the preferential conditions for the complex formation. The highest binding efficiency of the drug to the cationic dendrimer was observed under basic conditions when the DOX molecule was deprotonated. The decrease in the zeta potential of the complex confirms that DOX immobilizes through electrostatic interaction with the carrier's surface amine groups. The binding constants were determined from the fluorescence quenching of the DOX molecule in the presence of G4.0 PAMAM. The two-fold way of binding doxorubicin in the structure of dendrimers was visible in the ITC isotherm. Fluorescence spectra and release curves identified reversible binding of DOX to the nanocarrier. Among the selected cancer cells, the most promising anticancer activity of G4.0-DOX was observed in A375 malignant melanoma cells. Moreover, the preferred intracellular location of the complexes concerning the free drug was found, which is important from a therapeutic point of view.

The development of plant-based meat analogues has become a significant challenge for the food industry in recent years due to the increasing demand for sustainable and healthier proteins in the context of a global protein transition. Plant-based meat analogues imitate the visual, textural, and chemical properties of traditional meat products and are required to closely resemble meat to appeal to consumers. In addition, consumers demand natural, clean-label, and nutritional and healthy products. To address these challenges, the food industry must develop highly healthy, nutritious, and E-number-free meat analogue products. Understanding the functionality of each ingredient and its role in the food matrix is crucial to being a key player in the innovation of the meat analogues market. This review provides updated information on the primary ingredients utilized for the development of plant-based burger meat alternatives and their functionality. The key components of meat analogue burgers are outlined, including plant proteins, binding agents, fats and oils, flavorings, colorings, preservatives, fortificants, and clean-label considerations.

Detection of early stage corrosion on slender steel members is crucial for preventing buckling failures of steel structures. An active photoacoustic fiber optic sensors (FOS) system has been reported for early stage steel corrosion detection of steel plates and rebars using surface ultrasonic waves. The objective of this paper is to investigate the surface corrosion/rust detection problem on steel rods using numerically simulated surface ultrasonic waves. The finite element method (FEM) is applied in simulating the propagation of ultrasonic waves on steel rod models. Transmission mode of damage detection is adopted, in which one source (transmitter) and one sensor (receiver) are considered. In this research, radial displacements at the receiver were simulated and analyzed by short-time Fourier transform (STFT) for detecting, locating, and quantifying a surface rust located between the transmitter and the receiver. From our time domain and frequency domain analyses, it is found that the presence, location, and dimensions (length, width, and depth) of surface rust can be estimated by ultrasonic waves propagating through the surface rust.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

Particle deposition on the surface of the drying chamber poses the main drawback in the spray drying process, which reduces the product recovery and affects the quality of the product. In view of this, the potential application of chemical surface modification to produce a hydrophobic surface that reduces the powder adhesion (biofouling) on the wall of the drying chamber was investigated in this study. The hydrophobic Polydimethylsiloxane (PDMS) solution was used in the vertical dipping method at room temperature to determine the optimum coating parameters on borosilicate glass and stainless-steel substrates, which were used to mimick the wall surface of the drying chamber, to achieve highly hydrophobic surfaces. A single-factor experiment was used to define the range of the PDMS concentration and treatment duration using the Response Surface Methodology (RSM). The Central Composite Rotatable Design (CCRD) was used to study the effects of the concentration of the PDMS solution (X1, %) and the treatment duration (X2, hr) on the contact angle of the substrate (°), which reflected the hydrophobicity of the surface. A three-dimensional (3D) response surface was constructed to examine the influence of the PDMS concentration and treatment duration on the contact angle readings, which serve as an indicator of the surface's hydrophobic characteristic. Based on the optimisation study, the PDMS coating for the borosilicate glass achieved an optimum contact angle of 99.33° through the combination PDMS concentration: X1 = 1% (w/v) and treatment time X2 = 4.94 hr, while the PDMS coating for the stainless-steel substrate achieved an optimum contact angle of 98.31° with PDMS concentration: X1 = 1% (w/v) and treatment time X2 = 1 hr. Additionally, the infrared spectra identified several new peaks that appeared on the PDMS-treated surfaces, which represented the presence of Si-O-Si, Si-CH3, CH2, and CH3 functional groups for the substrates coated with PDMS. Furthermore, the surface morphology analysis using the Field Emission Scanning Electron Microscopy (FESEM) showed the presence of significant roughness and uniform nanostructure on the surface of PDMS-treated substrates, which indicated the reduction of wettability and the potential effect on unwanted biofouling on the spray drying chamber.

Incidental findings (IFs) depicted in imaging tests during diagnostic evaluation of patients with cleft lip and/or palate (CL/P) can guide clinicians during treatment-planning procedures for effective, comprehensive cleft care. Evidence regarding IFs in different anatomical regions distant from the dentition are scarce. The aim of this study was to compare the prevalence of IFs in various anatomical areas between patients with non-syndromic CL/P and unaffected subjects. Orthopantomographs (OPT), lateral cephalometric (LC) radiographs and cone-beam computed tomography (CBCT) scans of 120 subjects (case group: n = 40, 18 females, age 14.5 ± 5.0 years; control group: n = 80, 36 females, age 14.6 ± 4.9 years) were examined and IFs were assessed by four observers. Significantly higher prevalence of IFs (p &lt; 0.001) was reported in the case group (97.5%) compared with the control group (62.5%). The most prevalent location of IFs in the case group was the maxilla (92.5%), followed by the nasal cavity (75.8%) and the mandible (63.2%), while in the control group, the highest rates of IFs occurred in the maxilla (43.8%), mandible (41.3%) and temporomandibular joint (TMJ) (14.7%). No gender-dependent pattern for IF occurrence was detected overall. Orofacial clefts may affect the mandible. However, the reported IFs were limited compared to those in the maxilla. In conclusion, individuals with CL/P are more likely to present with a range of IFs than their unaffected peers. Understanding the association between CL/P and IFs is critical for successful interdisciplinary treatment, raising awareness of the potential need for future dental care for cleft patients, and managing extra-dental aberrations. A systematic assessment of diagnostic records is required to eliminate the risk of overlooking clinically significant IFs.

Using numerical simulation method, combined with the pre-branch material characteristics of the measurement results, based on the LS-DYNA software to simulate the branch crushing process, the analysis found that not only the existence of the cutter cutting in the branch destruction process, there is also the cutting of the opposing surface of the bending fracture, with the increase in the speed of the knife rollers, the cutter cutting resistance increases, the cutting resistance reaches 2690 N when the cutter at 2500 r/min, the cutter cutting resistance is the smallest in the cutting simulation at the blade angle of 55°, the blade angle is more suitable for the cutting of the branch. In the cutting simulation under different cutting edge angles, the cutting resistance of the tool is the smallest when the edge angle is 55°, which is 1860 N. This edge angle is more suitable for branch crushing and cutting. Using Fluent software to analyse the airflow characteristics of the crushing device, it was found that with the increase of the knife roller speed, the inlet flow and negative pressure of the crushing chamber are increasing, the speed of 2500 r/min, the inlet flow and negative pressure were 1.92 kg/s and 37.16 Pa, which will be conducive to the feeding of branches, but the speed is too high and it will also lead to the enhancement of the vortex of part of the area in the crushing device, which will affect the feeding of branches and the throwing of the crushed material. affect the feeding of branches and the throwing out of crushed materials, and finally determined the speed range of the crushing knife roller is 1800 ~ 2220 r/min. Based on ANSYS/Model module modal analysis of the crushing knife roller, the knife roller of the first six orders of the intrinsic frequency and vibration pattern, crushing knife roller of the lowest order of the modal intrinsic frequency of 137.42 Hz, much larger than the crushing knife roller operating frequency of 37 Hz, the machine will not resonate during operation.

In response to the structural optimization problem of PCB stator coreless disc motors, the orthogonal response surface method was used to optimize the motor structure, determine the basic parameters of the motor preliminarily, and conduct orthogonal experiments on the motor parameters based on the optimization design objectives, The optimization factors were the quantity of magnetic pole of the motor rotor, the ratio of main/auxiliary pole size, the thicknessof the permanent magnet, and the air gap length.The motor torque，the amplitude of magnetic density of the air gap and waveform distortion rateare used as optimization objectives. The motor parameters that make the motor torque reach the maximum, the air gap magnetic density maximum, and the waveform distortion rate minimum. Due to the use of PCB plates instead of motor stator cores in PCB coreless disc motors,The service life of the PCB board during motor operation will be reduced with the temperature rise generated by the stator winding To solve this problem, the response surface analysis of the motor is carried out to reduce the temperature rise of the stator windings during the operation of the motor. PCB board and stator winding are the main factors affecting the temperature rise of the motor.Taking the thickness of the PCB board, the hole diameter on the board, and the uneven width of the stator winding as optimization factors, the motor parameters with the lowest temperature rise of the motor winding are obtained. Simulation analysis is conducted using Ansys/Maxwell software, and the results prove the feasibility of optimization.

In today’s rapidly evolving digital landscape, the significance of password guessing techniques in both offensive and defensive strategies is paramount. Passwords serve as a crucial line of defense for both individuals and corporations, safeguarding their sensitive systems and data. Therefore, assessing the effectiveness of these access credentials is a critical task. However, existing research in this field often encounters limitations, such as a lack of sufficient training data and extended model training times. Current methods often struggle with limited training data and lengthy training times. This paper introduces BBPE-AE, a novel Auto Encoder Network (AE) designed for password guessing. BBPE-AE utilizes Byte-level Byte Pair Encoding (BBPE) to extract frequent tokens from password datasets without length restrictions, employing a dynamic window technique to capture complex patterns. Experimental results on Hotmail and Myspace datasets demonstrate exceptional performance, achieving high similarity rates (BLEU-Unigram: 0.90, BLEU-Bigram: 0.82 for Hotmail; BLEU-Unigram: 0.90, BLEU-Bigram: 0.81 for Myspace). BBPE-AE generates realistic passwords that meet HIBP (Have I Been Pwned) standards, minimizing duplication. These findings highlight the effectiveness of BBPE-AE in enhancing security by generating realistic passwords, ultimately safeguarding sensitive systems and data.

This paper introduces a rigorous and comprehensive approach for the assessment of marine shafting systems through the utilization of an advanced Pi-Theorem based scaling methodology. Integrating journal bearing similarity assessment and shaft-line scaling methodology with advanced dimensional analysis, the study aims to provide a methodology foundation for systematic replication and analysis of marine shafting systems through scaled models. The proposed scaling methodology ensures geometric and mechanical similarity in terms of shaft-line deflection, considering key scaling parameters such as shaft length, diameter, weight, loads, rotational speed, material properties, bearing locations, and offsets. The advanced dimensional analysis computes specific non-dimensional ratios to guarantee a close resemblance between a real-size system and a scaled lab model, enabling meaningful experimentation. The methodology is analytically derived and validated with numerical simulations for a case study, conducting comparative analysis, evaluating discrepancies, and utilizing the integrated framework for experimentation.

The paper provides a methodological framework based on Multiple Criteria Decision Aid methods for determining relative regional vulnerabilities associated with forest fires that occurred during a given period. Different notions of ex-post vulnerability are defined based on the forest area burned and the frequency of forest fires, and their relation to the regions’ area and several socioeconomic characteristics. The methodology is applied to Greece and its administrative regions for the period 2000–2022. Linking the forest fire events with summer and spring temperatures and precipitation and using econometric count data analysis, the paper explores the climatic drivers of forest fire occurrence and provides projections of the expected change in the frequency of fires of specific size classes conditional on the evolution of mean seasonal regional temperature and precipitation according to IPCC scenarios. The results regarding relative regional vulnerabilities and expected forest fires could be useful in designing policies for preserving forests as natural capital and promoting sustainability.

Typhoons bring great damages to transmission line systems located in coastal areas. Strong wind and extreme precipitation are the main sources of damaging effects. Transmission lines suffered from wind-driven rain exhibit more susceptibility to damage due to the coupled effect of wind and rain water. This paper presents an integrated numerical simulation framework based on mesoscale WRF model, multiphase CFD model and FEM model to analyze the motions of a transmission line subjected to coupled wind and rain loads during typhoon events. A full-scale transmission line in Zhoushan island is employed to demonstrate the effectiveness of the proposed framework by simulating typhoon evolution in terms of wind fields and rainfall, solving the coupled wind and rain fields around the conductor and predicting the dynamic responses of the transmission line during Super Typhoon Lekima (2019). The results show that the horizontal displacements of the transmission line under the joint actions of wind and rain increases approximately 17%~18% compared to those of wind loads only. It is important to consider the coupled effects of wind-driven rain on conductors in the design of transmission lines under typhoon conditions.

The origin of a product, consumer familiarity, and purchasing identity are factors that affect perception of cheese consumption. The present study aims at identifying consumers’ conceptualizations and attitudes towards local Greek cheeses of the North-Aegean Sea islands, such as Ladotyri, Graviera, Kasseri, Kaskavali, Melichloro, and Kalathaki, some of which have a Protected Designation of Origin (PDO) status, as opposed to cheeses of non-Greek origin, such as Cheddar, Regatto, and Gouda. Sensory and emotional attributes of local, local PDO, and imported cheeses, and drivers associated with consumers’ choice and acceptance above and beyond their sensory attributes were studied, using three methods: a) Flash Profile to gain insight into the sensory positioning of products and description of samples, b) qualitative analysis of focus groups to pinpoint consumer knowledge, preference, and consumption criteria, and c) a new methodology for natural language processing and sentiment analysis of social media posts to determine consumer conceptualizations. Social media posts have proven to be a valuable source of linguistic and cultural data for cheeses. Local cheeses, including PDO products, were found to be linked to village life and family gatherings, home, tradition, and childhood memories, with saltiness and hardness being their main sensory attributes. Imported cheeses were linked to fast food, pizza, and snacking, with elasticity and gumminess as prominent sensory qualities. The main criterion of purchase was intended usage and versatility, taste and texture, price, and familiarity. The findings provide key sensory attributes, information about consumer purchasing criteria, and relevant vocabulary for the promotion of cheeses as agri-food and gastronomic identity key products.

Axial resolution is one of the most important characteristics of a microscope. In all microscopes, a high axial resolution is desired in order to discriminate information efficiently along the longitudinal direction. However, when studying thick samples that do not contain laterally overlapping information, a low axial resolution is desirable as information from multiple planes can be recorded simultaneously from a single camera shot instead of plane-by-plane mechanical refocusing. In this study, we increased the focal depth of an infrared microscope non-invasively by introducing a binary axicon fabricated on barium fluoride substrate close to the sample. Preliminary results of imaging thick and sparse silk fibers showed an improved focal depth with a slight decrease in lateral resolution and increase in background noise.

In this work, we conducted a numerical study on the cavitation flow around a circular cylinder through the implementation of a porous coating. The primary objective addressed the effectiveness of utilizing a porous surface to control cavitation. We analyzed the cavitation dynamics around the cylinder and the hydrodynamic performance at different permeability levels of the porous surfaces. The flow was governed by the density based homogeneous mixture model and the volume penalization method was used to deal with the porous layer. A high-order accurate numerical method was adopted for the simulation of the cavitating flow through solving the preconditioned multiphase equations. The results revealed that the application of porous layer led to effective suppression of the cavitation vortex shedding. In addition, a reduction of the shedding frequency was obtained which accompanied by thinner and elongated vortices in the wake region of the cylinder. With the proper porous layer, the inception of the cavitation on the cylinder was suppressed and the amplitude of pressure pulsations due to the cavitation shedding mechanism was mitigated.

This study explores how the properties of heater materials impact nucleate pool boiling using a comprehensive simulation model. The model integrates well-known heat transfer mechanisms, allowing us to assess the effects of two distinct heater materials. Findings indicate that materials with higher thermal conductivity, such as copper, notably improve refrigeration efficiency in nucle- ate boiling. The study provides insights into the relationship between bubble growth, microlayer recovery beneath a bubble, temperature fluctuations, and heater properties. Comparisons between copper and silicon oxide underscore variations in bubble frequency, attributed to differences in bubble growth time, microlayer recovery time, and material-dependent behavior. The influence of neighboring bubbling sites, especially pronounced in silicon oxide due to its low thermal conductivity and diffusivity, was observed. Temperature variations in such materials became highly visible due to their significant inertia in recovery. Simulation results align well with empirical correlations, confirming the model’s versatility in capturing the intricate phenomena of nucleate pool boiling.

The study used ERA5 reanalysis SST dataset re-gridded to a common grid of 0.25° X 0.25° spatial resolution (latitude × longitude) for the historic (1940–2014) and projected (2015–2100). The SST simulation under the SSP5-8.5 scenarios was carried out with output from 8 General Circulation Models (GCMs). The bias-corrected dataset was developed using Empirical Quantile Mapping EQM for the historical (1940-2015) and the future (2030-2100) while the CMIP6 model simulation was evaluated against the ERA5 monthly rainfall observed data for monthly and annual sea surface temperatures (SST) over the Gulf of Guinea. ). The CMIP6 models simulation for SST projection from 2030-20100 based on SSPS 8.5 SST is projected to increase by 4.61o (31oC) in 2030 to 35oC in 20100 in the coastal GOG and 2.6oC in the Western GOG (Sahel). The correlation coefficient (r) was used to evaluate the performance of the CMIP6 models and the analysis showed ACCESS 0.1,CAMS CSM 0.2, CAN ESM 0.3, CMCC, 0.3 and MCM, 0.4 indicating that all models performed well in capturing the climatological pattern of the SST. The.CMIP6 bias corrected model simulations showed increased SST warming over the GOG will be higher in the Far period end than the Near-term climate. The study affirmed that the CMIP6 projections can be used for multiple assessments related to climate and hydrological impact studies and for the development of mitigation measures under a warming climate

This work introduces a novel numerical method designed to address three-dimensional unsteady free surface flows incorporating integral viscoelastic constitutive equations, specifically, the K-BKZ-PSM (Kaye–Bernstein, Kearsley, Zapas - Papanastasiou, Scriven, Macosko) model. The new proposed methodology employs a second-order finite difference approach along with the deformation fields method to solve the integral constitutive equation, and the marker-particle method (known as \emph{Marker-and-Cell}) to accurately capture the evolution of the fluid's free surface. The newly developed numerical method has proven its effectiveness in handling complex fluid flow scenarios, including confined flows and extrudate swell simulations of Boger fluids. Furthermore, a new semi-analytical solution for velocity and stress fields is derived, considering fully developed flows of a K-BKZ-PSM fluid in a pipe.

The link between the world of communication and the world of racing is provided by telemetry systems in electric racing cars. These systems send real-time data about the vehicle’s behavior and systems to enable informed decisions during the race. The aim of this research was to integrate telemetry into the battery bank of a racing electric vehicle to find the optimal values of current and voltage that optimize the charging process, thus improving the vehicle’s performance in competition using Response Surface Analysis. Particularly, the telemetry system consisted of an Arduino Mega, a digital wattmeter, and temperature sensors, all installed in the vehicle. Once the telemetry data was obtained, a response surface design was adapted with current, voltage, and temperature as factors, varying from low to high values, with the objective function being to minimize the battery’s charging time. Applying the response surface methodology and the steepest descent algorithm, it was found that all factors significantly affect the charging time, with the minimum charge time being 6961 seconds, obtained with a current of 2.4 amps and voltages of 50.5 volts and 43.6 volts.

We report on ground-based measurements of the atmospheric electric field (Ez= -Potential Gradient (PG)) and current density (Jz) that were conducted at two locations in Israel. One is the Emilio Segre cosmic ray station located on Mt. Hermon (34.45 N, 2020 m AMSL) located in northern Israel near the Syrian-Lebanon border and at the other at the Wise astronomical observatory in the Negev desert highland plateau of southern Israel (31.18 N, 870 m AMSL). We searched for possible effects of strong, short-term solar events on the potential gradient and the vertical current density, as disruption to the Global Electric Circuit are often observed following strong solar events. The first case study (St. Patrick Day, 17 March 2015) was classified as the strongest event of 2015. The second case study (8 Sep 2017) was categorized as the strongest event of 2017 and one of the twenty strongest events on record to date. The results show that the electrical parameters measured at ground level at both stations were not affected during the two massive proton events and the ensuing geomagnetic storms. The magnetospheric shielding in lower latitudes is strong enough to shield against flux of energetic particles from solar events, obscuring any impact that may be noticeable above the local daily variations induced by local meteorological conditions (aerosol concentrations, clouds, high humidity, and wind speed) which were investigated as well.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

Ti-Al based alloys, particularly TiAl and Ti3Al two-phase alloys, have garnered significant attention as potential replacements for various high-temperature structural materials due to their exceptional properties, including low density, oxidation resistance, and high strength at elevated temperatures. Despite these advantages, experimental studies on the microstructure evolution of Ti-Al based alloys under complex conditions remain challenging to observe and characterize. This review article examines the current research on molecular dynamics (MD) simulations of Ti-Al based alloys, focusing on two-phase Ti-Al alloys, Ti-Al amorphous alloys, Ti-Al composite materials, and the welding and multi-layer/film applications of Ti-Al alloys. The review highlights the unique capabilities of MD simulations in predicting the behavior of Ti-Al based alloys and addresses existing scientific challenges. Furthermore, the article discusses future research directions and development prospects in this field.

Researchers have explored primary colour-geometric shape associations since Kandinsky's correspondence theory. However, there is a gap in the literature regarding interior colour applications on surface shapes. To address this gap, an online study was employed to gather data with one hundred participants who were asked to choose their preferred colours for shapes on bedroom walls with follow-up questions on the colour-shape semantic associations, their preference of colours and shapes on bedroom walls independently in addition to their favourite colour, their favourite shape, and colour-shape pairs without interior context. The results revealed that colour-shape preferences in interiors differ from those found in psychology studies, other colour applications on bedroom walls, and other preferences, indicating that colour preference is context-dependent. Interestingly, the most popular colour for surface shapes on bedroom walls is purple, followed by brown and blue. The study contributes to the existing literature by providing colour charts for bedroom applications for professionals in the industry, their clients/users, and future studies.

The implementation of management systems has become a strategic advantage in achieving business goals, especially in industrial organizations, but the implementation of social responsibility requirements is especially ethical. Large multinational companies have long been developing and, in particular, implementing their own codes of conduct, which include their suppliers, to demonstrate their commitment to Corporate Social Responsibility (CSR). The compliance with CSR requirements from stakeholders is thus extended or intertwined with requirements in established management systems (MSs). The objectives of the study were to (1) analyze the different approaches to CSR in internationally recognized cross-industry and industry-specific standards and codes in different industries; (2) select the most appropriate framework for assessing the degree of applicability of CSR in the selected management systems and develop a methodology for its assessment; (3) apply the proposed methodology (referred to as SRIMS) in the selected areas: automotive industry, research organization, and metallurgical industry; (4) through ANOVA, validate its use for assessing the overall level of CSR applicability in an organization's established management systems. The application of the Bonferroni method confirmed the hypotheses that the developed SRIMS model is a sufficiently appropriate tool for assessing the overall level of applicability of CSR requirements to established MSs.

Sulfate, the main dissolved contaminant in acid mine drainage (AMD), is ubiquitous in watersheds affected by coal and metal mining operations worldwide. Engineered passive bioremediation systems (PBS) are low-cost technologies that remediate sulfate contamination by promoting (1) precipitation of sulfate-bearing compounds, such as schwertmannite and gypsum; and (2) microbially-mediated sulfate reduction (BSR) to sulfide with subsequent precipitation of sulfide minerals. In this study, chemical and sulfur isotopic data are used to infer multiple pathways for sulfate sequestration in the Tab-Simco PBS. By simultaneously monitoring sulfate concentrations and δ34SSO4 values at four sampling points across the PBS, we (1) identified that the organic layer within the bioreactor was the primary site of BSR processes contributing to sulfate sequestration; (2) observed seasonal variations of BSR processes; (3) estimated that initially the BSR processes contributed up to 30% to sulfate sequestration in the Tab-Simco bioreactor; and (4) determined that BSR contribution to sulfate sequestration continuously declined over the PBS operational lifetime. Together, our results highlight the utility of combining geochemical and microbial fingerprinting techniques to decipher complementary processes involved in sulfur cycling in a PBS as well as the value of adding the sulfur isotope approach as an essential tool to help understand, predict, prevent and mitigate sulfate contamination in AMD-impacted systems.

The optimal functionality and dependability of mechanical systems are important for the sustained productivity and operational reliability of industrial machinery which has direct impact on it’s longevity and profitability. Therefore, failure of a mechanical system or any of it component would be detrimental to production continuity and availability. Consequently,this study proposes a robust diagnostic framework for analyzing the blade conditions of shot blast industrial machinery. The framework involves analyzing the spectral characteristics of the vibration signals generated by Industrial Shot Blast. Additionally, a peak detection algorithms is introduced to identify and extract the unique features present in the peak magnitudes of each signal spectrum. A feature importance algorithm is then deployed as the feature selection tool, and these selected features are fed into 10 machine learning classifier, with Extreme gradient boosting (XGB) as the core classifier. Results show that the XGB classifier achieved the best accuracy of 98.05%, with a cost-efficient computational cost of 0.83 seconds. Other global assessment metrics were also implemented in the study to further validate the model.

This paper presents a numerical study on the laser shock wave propagation in a 3D woven CFRP material by means of detailed and homogenized FE models. The aim of the study is to numerically characterize the shock wave response of the 3D woven CFRP in terms of back face velocity profiles and the induced damage and to investigate whether the detailed FE models could be replaced by homogenized FE models. The 3D woven geometry was designed using the TexGen software, while the numerical analyses were executed using the LS-Dyna explicit FE software. A high-strain rate behavior was considered for the matrix. The fiber bundles in the detailed models were modeled as a high fiber content unidirectional composite laminate, with its mechanical properties calculated by micromechanical equations. Both for the fiber bundles of the detailed model and the homogenized models a progressive damage material model was applied. The results of the detailed model reveal a considerable effect of material’s architecture on the shock wave propagation and the sensitivity of the back face velocity profile to the spot location. Consequently, the homogenized model is not capable of accurately simulating the shock wave response of the 3D woven composite. Moreover, the detailed predicts with high accuracy matrix cracking in the resin-rich areas and in the bundles as well as fiber failure. On the contrary, the homogenized model predicts matrix cracking at the same areas and no fiber failure.

The amplified Arctic warming is one of several factors influencing atmospheric dynamics. In this work, we consider a series of numerical experiments to identify the direct role of the Arctic sea ice reduction process in forming climatic trends in the northern hemisphere. Aimed at this, we used two more or less independent mechanisms of ice reduction. The first is traditionally associated with increasing the concentration of carbon dioxide in the atmosphere from the historic level of 360 ppm to 450 ppm and 600 ppm. This growth increases air temperature and decreases the ice volume. The second mechanism is associated with a reduction in the reflectivity of ice and snow. We assume that comparing the results of these two experiments allows us to judge the direct role of ice reduction. The most prominent consequences of ice reduction, as a result, were the weakening of temperature gradient at the tropopause level in mid-latitudes, the slower zonal wind at 50-60∘N, intensification of wave activity in Europe, Western America, and Chukotka, and its weakening in the south of Siberia and Kazakhstan. We also consider how climate change may alter regimes such as blocking and stationary Rossby waves. The study used the INM-CM48 climate system model .

The amount of solar energy produced is directly proportional to the surface area of solar panels exposed to sun rays. To increase the productivity of solar panels, a number of techniques are proposed by curving the surface or protruding the panel surface to maximise the surface area, e.g. Protruding panel surfaces with shapes such as pyramidal, cone, spherical cap, sinusoidal wavy curve, etc. These techniques are analysed to determine whether the panel surface area increases. The geometrical design analysis showed that, depending on the chosen surface curving method, the panel can achieve a remarkable increase in surface area.The system advisor model was used to assess a sample of solar cells with standard measurements of 6 by 6 inches that were organised in a zigzag pattern with different angles of inclination (10°, 15°, 20°, 25°, 30°, and 35°). Overall, the maximum power pump and annual AC energy performance increase by 1.4%, 4.2%, 6.8%, 10.8%, 14.9%, and 21.6%, respectively, over a one-year period of productivity. However, by applying the concept of solar panel efficiency degradation due to tilting solar panels at an angle by Mamun et al. (2022), for each 5° increase in tilt angle beyond the ideal 10°, the efficiency decreases by approximately 0.76%. In conclusion, the overall efficiency is greater than that of standard flat solar panels, provided the tilt angle is within a reasonable range.

The development of virtual models has recently been generalized in the field of complex mechatronic product design. Virtual models have various advantages such as: the systemic design approach, most often parametric, the implementation of extreme, expensive, and perhaps risky scenarios for the operation of the designed product, the testing of a large number of variants, etc. The main contribution of the paper consists of the development of an interface family called DeSeRoI (Dedicated Serial Robot Interface). Each member of the interface family integrates Simulink libraries and is created by the programmer in accordance with user requests. It follows that the interfaces composing the DeSeRoI family can have different levels of complexity depending on user needs and constraints. We are implementing a MATLAB-based application with user-provided configuration for serial robots in order to automatically visualize the kinematics data and simulation. Within MATLAB, two scripts are created responsible for generating Simulink models that compute the kinematics problem. One of the scripts (Main) saves information about the configuration of the robot and the other one (Generates_Simulink_Models) computes the kinematics problem. Different types of functions (software module) have been developed. Using these functions, the Simulink models result as modular entities. The automated approach eases user’s interaction and understanding of serial robots’ kinematics by performing the simulation procedure in a shorter amount of time and with higher efficiency, assuring a precise outcome despite the chosen parameters.

This study aimed to develop a state-of-the-art method for assessing chemical risks. The method combined desk research findings and the authors' practical knowledge to identify the major shortcomings in performing risk assessments at the workplace. Data were collected from nine SMEs across three sectors: agriculture, laboratory research, and conservation and restoration laboratories. The results of the discussions with the workers and on-site observations were used to develop the method to assess chemical risks. The method uses numerical factors to account for the level of conformity and the duration of exposure to support an estimation of the probability of an incident. The developed method was designed to enhance risk assessment practices and tackle common issues encountered by enterprises, including SMEs.