This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

Large-scale hydrological modeling in China is challenging given the sparse meteorological stations and large uncertainties associated with atmospheric forcing data.Here we introduce the development and use of the China Meteorological Assimilation Driving Datasets for the SWAT model (CMADS) in the Heihe River Basin(HRB) for improving hydrologic modeling, by leveraging the datasets from the China Meteorological Administration Land Data Assimilation System (CLDAS)(including climate data from nearly 40000 area encryption stations, 2700 national automatic weather stations, FengYun (FY) 2 satellite and radar stations). CMADS uses the Space Time Multiscale Analysis System (STMAS) to fuse data based on ECWMF ambient field and ensure data accuracy. In addition, compared with CLDAS, CMADS includes relative humidity and climate data of varied resolutions to drive hydrological models such as the Soil and Water Assessment Tool (SWAT) model. Here, we compared climate data from CMADS, Climate Forecast System Reanalysis (CFSR) and traditional weather station (TWS) climate forcing data and evaluatedtheir applicability for driving large scale hydrologic modeling with SWAT. In general, CMADS has higher accuracy than CFRS when evaluated against observations at TWS; CMADS also provides spatially continuous climate field to drive distributed hydrologic models, which is an important advantage over TWS climate data, particular in regions with sparse weather stations. Therefore, SWAT model simulations driven with CMADS and TWS achieved similar performances in terms of monthly and daily stream flow simulations, and both of them outperformed CFRS. For example, for the three hydrological stations (Ying Luoxia, Qilian Mountain, and ZhaMasheke) in the HRB at the monthly and daily Nash-Sutcliffe efficiency ranges of 0.75-0.95 and 0.58-0.78, respectively, which are much higher than corresponding efficiency statistics achieved with CFSR (monthly: 0.32-0.49 and daily: 0.26 – 0.45). The CMADS dataset is available free of charge and is expected to a valuable addition to the existing climate reanalysis datasets for deriving distributed hydrologic modeling in China and other countries in East Asia.

Large-scale crowd phenomena are complex to model because the behaviour of pedestrians needs to be described at both strategic, tactical, and operational levels and is impacted by the density of the crowd. Microscopic models manage to mimic the dynamics at low densities, whereas mesoscopic models achieve better performances in dense situations. This paper proposes and evaluates a novel agent-based architecture to enable agents to dynamically change their operational model based on local density. The ability to combine microscopic and mesoscopic models for multi-scale simulation is studied through a use case of pedestrians at the Festival of Lights, Lyon, France. Pedestrian outflow data is extracted from video recordings of exiting crowds at the festival. The hybrid model is calibrated and validated using a genetic algorithm that optimizes the match between simulated and observed outflow data. Additionally, a local sensitivity analysis is then conducted to identify the most sensitive parameters in the model. Finally, the performance of the hybrid model is compared to different models in terms of density map and computation time. The results demonstrate that the hybrid model has the capacity to effectively simulate pedestrians across varied density scenarios while optimizing computational performance compared to other models.

Effective household and individual disaster preparedness can minimize physical harm and property damage during catastrophic events. To assess the risk and vulnerability of affected areas, it is crucial for relief agencies to understand the level of public preparedness. Traditionally, government agencies have employed nationwide random telephone surveys to gauge the public’s attitudes and actions towards disaster preparedness. However, these surveys may lack generalizability in certain affected locations due to low response rates or areas not covered by the survey. To address this issue and enhance the comprehensiveness of disaster preparedness assessments, we develop a framework that seamlessly integrates machine learning and simulation. Our approach leverages machine learning algorithms to establish relationships between public attitudes towards disaster preparedness and demographic characteristics. Using Monte Carlo simulation, we generate datasets that incorporate demographic information of the affected location based on government-provided demographic distribution data. The generated dataset is then input into the machine learning model to predict the disaster preparedness attitudes of the affected population. We demonstrate the effectiveness of our framework by applying it to Miami-Dade County, where it accurately predicts the level of disaster preparedness. With this innovative approach, relief agencies can have a clearer and more comprehensive understanding of public disaster preparedness.

Conditions under which compositions of component systems form a well-defined system-of-systems here are formulated at a fundamental level. Statement of what defines a well-defined composition and sufficient conditions guaranteeing such a result offers insight into exemplars that can be found in special cases such as differential equation and discrete event systems. For any given global state of a composition, two requirements can be stated informally as: 1) the system can leave this state, i.e., there is at least one trajectory defined that starts from the state, and 2) the trajectory evolves over time without getting stuck at a point in time. Considered for every global state, these conditions determine whether the resultant is a well-defined system and if so, whether it is non-deterministic or deterministic. We formulate these questions within the framework of iterative specifications for mathematical system models that are shown to be behaviorally equivalent to the Discrete Event System Specification (DEVS) formalism. This formalization supports definitions and proofs of the afore-mentioned conditions. Implications are drawn at the fundamental level of existence where the emergence of a system from an assemblage of components can be characterized. We focus on systems with feedback coupling where existence and uniqueness of solutions is problematic.

In econometrics and finance, volatility modelling has long been a specialised field for addressing a variety of issues pertaining to the risk and uncertainties of an asset. This study presents a robust framework, through a step-by-step design, that is relevant for effective Monte Carlo simulation (MCS) with empirical verifications to estimate volatility using the Generalized Autoregressive Score (GAS) model. The framework describes an organised approach to the MCS experiment that includes "background (optional), defining the aim, research questions, method of implementation, and summarised conclusion". The method of implementation is a workflow that consists of writing the code, setting the seed, setting the true parameter a priori, data generation process, and performance assessment through meta-statistics. Among the findings, it is experimentally demonstrated in the study that the GAS model with a lower unconditional shape parameter value can generate a dataset that adequately reflects the behaviour of financial time series data, relevant for volatility estimation. This dynamic framework is intended to help interested users on MCS experiments utilising the GAS model for reliable volatility calculations in finance and other areas.

This study rolls out a robust framework relevant for simulation studies through the Generalised Autoregressive Conditional Heteroscedasticity (GARCH) model using the rugarch package. The package is thoroughly investigated, and novel findings are identified for improved and effective simulations. The focus of the study is to provide necessary simulation steps for volatility estimation that involve "background (optional), defining the aim, research questions, method of implementation, and summarised conclusion". The method of implementation is a workflow that includes writing the code, setting the seed, setting the true parameters a priori, data generation process and performance assessment through meta-statistics. This novel, easy-to-understand steps are demonstrated on financial returns using illustrative Monte Carlo simulation with empirical verification. Among the findings, the study shows that regardless of the arrangement of the seed values, the efficiency and consistency of an estimator generally remain the same as the sample size increases. The study also derived a new and flexible true-parameter-recovery measure which can be used by researchers to determine the level of recovery of the true parameter by the MCS estimator. It is anticipated that the outcomes of this study will be broadly applicable in finance, with intuitive appeal in other areas, for volatility estimation.

Lateral vehicle control is a high importance in automated vehicles as it directly influences the vehicle’s performance and safety during operation. The Linear Quadratic Regulator (LQR) controller stands out due to its high-performance characteristics and is used in the open source for self driving functions. However, a notable limitation of the current approach is the manual calibration of LQR controllers based on the experience and intuition of the designers, leading to empirical uncertainties. To address this issue and enhance the lateral control performance, this paper concentrates on refining the LQR by employing three optimization algorithms: Artificial Bee Colony Optimization (ABC), Genetic Algorithm (GA), and Particle Swarm Optimization (PSO). These algorithms aim to overcome the reliance on empirical methods and enable a data-driven approach to LQR calibration. By comparing the outcomes of these optimization algorithms to the manual LQR controller within an offline multibody simulation as testing platform, the study highlights the superiority of the best-performing optimization approach. Following this, the optimal algorithm is implemented on a real-time system for the full vehicle level, revealing the Model-in-the-Loop and the Hardware-in-the-Loop gap up to 78,89% with lateral velocity when we use Relative Error Criterion (REC) method to validate and 2.35m with lateral displacement when considering by maximum absolute value method.

For the emerging autonomous swarm technology, from the perspective of systems science and systems engineering, there must be some novel elements and methods to aggregate multiple systems into a group, which distinguish with the general components with specific functions, and we expect to provide the presentation of their existence in the swarm development processes. The inspiration of our methodology origins from the integration of swarm ontology, multi-paradigm modeling, multi-agent system, cyber-physical system, etc. Therefore, we choose the model-driven technology as a framework to acquire an approach of model representation across the multiple levels of abstraction and composition. The autonomous strategic mechanism is defined and formed in parallel with ConOps analysis and systems design, so as to effectively solve the cognitive problem of emergence caused by the nonlinear causation among individual and whole behaviors. This approach highlights to use the MBSE processes and their artifacts to embed the meso mechanism to integrate the operational and the functional, and which means to connect the macro and micro aspects in formalism and so to become a whole with its expected goals, and then to verify and validate within a L-V-C simulation environment.

The increasingly used approach of combining different simulation software in testing of automated driving systems (ADS) increases the need for potential and convenient software designs. Recently developed co-simulation platforms (CSP) provide the possibility to cover the high demand on testing kilometers for ADS by combining vehicle simulation software (VSS) with traffic flow simulation software (TFSS) environments. The emphasis on the demand of testing kilometers is not enough to choose a suitable CSP. The complexity level of the used vehicle, object, sensors and environment models is essential for valid and representative simulation results. Choosing a suitable CSP raises the question of how the test procedures should be defined and constructed and what the relevant test scenarios are. Parameters of the ADS, the environments, objects, sensors in VSS as well as traffic parameters in TFSS can be used to define and generate test scenarios. In order to generate a large number of scenarios in a systematic and automated way, suitable and appropriate software designs are required. In this paper we present a software design for CSP based on the Model-View-Controller (MVC) design pattern and implementation of a complex CSP for virtual testing of ADS. Based on this design, an implementation of a CSP is presented using the VSS from IPG Automotive called CarMaker and the TFSS from PTV Group called Vissim. The results have shown that the presented CSP design and the implementation of the co-simulation can be used to generate relevant scenarios for testing of ADS.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

Collision avoidance is an important feature in advanced driver-assistance systems, aiming at providing correct, timely and reliable warnings before an imminent collision (objects, vehicles, pedestrians, etc.). A co-simulation framework is proposed in this paper to address the design and evaluation of collision avoidances in a cyber-physical system. The co-simulation framework is supported on the interaction between SCANeR and Matlab/Simulink. From the best of authors’ knowledge, two main contributions are reported in this paper. Firstly, the modelling and simulation of virtual on-chip LIDAR sensors in a cyber-physical system (CPS) considering traffic scenarios is presented. The CPS is designed and implemented in SCANeR. Secondly, an obstacle recognition library with three specific Artificial Intelligence-based methods is also designed based on sensory information database provided by SCANeR. Three methods for collision avoidance detection are considered, i.e.; a multi-layer perceptron neural network, a self-organization map and a support vector machine. Finally, a comparison among these methods for detecting obstacles before different weather conditions is done with very promising results in terms of accuracy. The best results are achieved using the multi-layer perceptron in sunny and fog conditions, the support vector machine in rainy and self-organized map in snowy conditions.

As Artificial Intelligence (AI) technology, particularly Machine Learning algorithms, becomes increasingly ubiquitous, our abilities to understand and interpret AI and machine learning algorithms are becoming increasingly desirable. Visualization has been used as a common tool to view and understand complex machine learning processes. In this paper, we will focus on developing a general framework for the visualization of machine learning models as a scalar valued multi-dimensional function to help users understand how the models behave over different viewing spaces. We first give a formal definition of the visualization problem. Interpolation-based morphing and subspace sampling techniques are applied to generate various renderings through projections and cross-sections of the model space as 3D surfaces or heatmap images. This method will be applied to two real-world datasets and applications: the diagnosis of Alzheimer's Disease (AD) using a human brain networks dataset and a real-world benchmark dataset for predicting home credit default risks. The visualizations show that different machine learning algorithms can behave quite differently under different conditions.

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

This paper explores the relationships between marketing strategies, social media platforms, the adoption and diffusion of products and services, and organizational resilience to gain an understanding of the ability of organizations to cope with disruptive events (e.g., COVID-19). This can be achieved through effective marketing strategies and the efficient use of social media platforms. In fact, resilience thinking can help organizations maintain their operations by increasing the adoption and diffusion of their products and services through the use of effective marketing strategies. To achieve this article’s objectives, a literature review is conducted to help develop a conceptual framework that highlights a clear relationship between the previously discussed concepts. In addition, the novel nature of the relationship between marketing strategies and organizational resilience is dissected and its significance for organizations is demonstrated. In fact, the findings of this study suggest that effective marketing strategies that consider the "what," "who," and "how" dichotomies and the efficient use of social media to promote the adoption and diffusion of products and services can significantly enhance the resilience of organizations. These relationships can serve as a starting point for further studies examining and empirically analyzing marketing strategies and their positive effect on strengthening organizational resilience.

In this paper we report a new development on the numerical model for aluminum-steam combustion. This model is based on diffusion flame of continuum regime and the thermal equilibrium between the particle and the flow field, which can be used to calculate the aluminum particle combustion model for two phase calculation conditions. The model prediction is in good agreement with the experimental data. A new type of vortex combustor was proposed for the combustion of aluminum and steam, and the mathematical model of the two phase reacting flow with in this combustor was established. The turbulence effects are modeled using the Reynolds Stress Model (RSM) with Linear Pressure-Strain approach, and the Eddy-Dissipation model is used to simulate the gas phase combustion. Aluminum particles are injected into the vortex combustor and form a swirling flow around the chamber and their trajectories are traced using the Discrete Phase Model (DPM). The simulation results show that the vortex combustor can achieve high efficient combustion of aluminum and steam. The influencing factors, such as the eccentric distance of the inlet of aluminum particles, particle size and steam inlet diameter, etc., are studied. The work described in this paper represents an attempt to the design of a vortex combustor in order to increase aluminum combustion efficiency.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

Shear dynamics simulation under extreme pressure was used to optimise the composition of ester-based lubricant base oil and extreme pressure additives. As a result, the ester-based lubricant in the weak-gel drilling fluid achieves reduction and increases the efficiency in drilling construction, and the field operation efficiency improves. The results of base oil lubrication simulation show that three base oils, namely, methyl oleate, ethyl oleate and butyl oleate, can be stably adsorbed on the surface layer of the shear surface. Methyl oleate has the lowest system temperature after shear stabilisation and has a high load-bearing capacity. The shear stress of methyl oleate decreases by changing the initial shear temperature and speed. It increases by 6.36 MPa when the speed increases from 10 m/s to 30 m/s. At this time, the shear stress of butyl oleate increases by 10.11 MPa. The results of the four-ball friction experiments show that the radius of the abrasion spot of methyl oleate is 179.83 μm, which is smaller than that of the other two base oils. Moreover, the friction coefficient of methyl oleate is 0.0018, which is approximately 1/3 of that of butyl oleate. Methyl oleate has better lubrication efficiency. The shear simulation results are consistent with the experimental results. The simulation can be used for the molecular design of lubricant materials. The oleic acid amide–containing amine group and the glyceride oleic–containing hydroxyl group were selected as the extreme pressure functional components for shear simulation. Results show that the shear stress of oleic acid amide is much lower than that of oleic acid glyceride when the initial shear temperature and speed change. The extreme pressure lubrication component–containing amine group is better than the extreme pressure lubrication material–containing hydroxyl group. The effects of different oleamide contents in the two-component mixtures on the lubricating properties were investigated through shear simulation, with methyl oleate as the base oil and oleamide as the extreme pressure functional component. The simulation results show that the lubricant has the optimal shear stress when 10% oleamide is added to the lubricant. The base properties of the lubricant were tested using a mixture of 90% methyl oleate and 10% oleamide, formulated as a lubricant. Results show that the friction coefficient can be reduced to 0.03 when 0.5% of the lubricant is added to the base mud. Moreover, the lubricant film formed shows high strength. Then, 1% lubricant was added to the weak-gel drilling fluid to evaluate the effect of the lubricant on the gel structure of the drilling fluid. Results show that adding lubricant does not affect the rheological properties of the drilling fluid. The gel structure of the system also remains stable even after 7 days of continuous ageing. The results of the field experiments in Hua3-01 well show that adding 1% ester-based lubricant to the field drilling fluid reduces the drilling friction by 33%. Thus, the efficiency of directional side drilling can be effectively improved, complicated accidents, such as poor starting and stopping of drilling and stuck jamming, can be avoided, and the goals of reducing quantity and increasing efficiency can be completed.

Although, promotion of urbanization culture in recent decades has made inevitable development of cities in the world, however, the development can be guided in a direction that leave, to the extent possible, minimum socioeconomic and environmental impacts. For this, it is required to first forecast auto-spreading orientation of cities and suburbs in rural areas over time and then avoid shapeless growth of cities. This paper is an attempt to develop a dynamic hybrid model based on logistic regression (LR), Markov chain (MC), and cellular automata (CA) for prediction of future urban sprawl in fast-growing cities. The model was developed using 12 widely-used urban development criteria, whose significant coefficient was determined by logistic regression, and validated by relative operating characteristic (ROC) analysis. The validated model was run in Guilan, a tourist province in northern Iran with a very high rate of urban development. For this, changes in the area of urban land use were detected over the period of 1989 to 2013 and then, future sprawl of the province was forecasted by the years 2025 and 2037. The analysis results revealed that the area of urban land use was increased by more than 1.7 % from 36012.5 ha in 1989 to 59754.8 ha in 2013, and the area of Caspian Hyrcanian forestland was reduced by 31628 ha. The results also predicted an alarming increase in the rate of urban development in the province by the years 2025 and 2037, during which urban land use is predicted to develop 0.9 % and 1.38 %, respectively. The development pattern is expected to be uneven and scattered, without following any particular direction. The development will occur close to the existing or newly-formed urban basements as well as around major roads and commercial areas. This development, if not controlled, will lead to the loss of 13863 ha of Hyrcanian forests and if the trend continues, 21013 ha of Hyrcanian forests and 20208 ha of Barren/open lands are expected to be destroyed by the year 2037. In general, the proposed model is an efficient tool for the support of urban planning decisions and facilitates the process of sustainable development of cities by providing decision-makers with an overview on future development of cities where the growth rate is very fast.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

Two coupled climate models which participated the CMIP6 project (Coupled Model Intercomparison Project Phase 6), the Earth System Model of Chinese Academy of Sciences version 2 (CAS-ESM2-0) and the Nanjing University of Information Science and Technology Earth System Model version 3 (NESM3), were assessed in terms of the impact of four new sea ice parameterization schemes. These four new schemes are related to air-sea heat flux, radiation penetration and absorption, melt ponds, ice-ocean flux, respectively. To evaluate the effectiveness of these schemes, key sea ice variables with and without these new schemes, such as sea ice concentration (SIC) and sea ice thickness (SIT), were compared against observation and reanalysis product from 1980 to 2014. The simulations followed the design of historical experiments within the CMIP6 framework. The results revealed that both models demonstrated improvements in simulating Arctic SIC and SIT when the new parameterization schemes were implemented. The model bias of SIC in some marginal sea ice zones of Arctic was reduced, especially during March. The SIT was increased and the transpolar gradient of SIT was reproduced. The changes of spatial pattern of SIC and SIT after adding new schemes bear similarities between the two coupled models. This suggests that the new schemes have potential for broad application in climate models, especially for those with underestimated SIT.

Tinnitus is a common phantom auditory percept, believed to be related to plastic changes in the brain due to hearing loss. However, tinnitus can also occur in absence of any clinical hearing loss. Then, since there is no hearing loss, the mechanisms that drive plastic changes remain largely enigmatic. Previous studies showed subtle differences in sound-evoked brain activity associated with tinnitus in subjects with tinnitus and otherwise, normal hearing, but the results are not consistent across studies. Here, we aim to investigate those differences using monaural rather than binaural stimuli. Sound-evoked responses were measured using functional magnetic resonance imaging (MRI) in participants with and without tinnitus. All participants had clinically normal audiograms. The stimuli were pure tones with frequencies between 353 and 8000 Hz, presented monaurally. A Principal Component Analysis (PCA) of the response in the auditory cortex revealed no difference in tonotopic organization, which confirmed earlier studies. A GLM analysis showed hyperactivity in the lateral areas of the bilateral auditory cortex. Consistent with the tonotopic map, this hyperactivity mainly occurred in response to low stimulus frequencies. This may be related to hyperacusis, which was associated with tinnitus found in the parahippocampus. This may reflect an interference between tinnitus and spatial orientation.

Closed timelike curves (CTCs), non-intuitive theoretical solutions of general relativity field equations can be modelled in quantum mechanics in a way, known as Deutsch-CTCs, to circumvent one of their most paradoxical implications, namely, the so-called grandfather paradox. An outstanding theoretical result of this model is the demonstration that in the presence of a Deutsch-CTC a classical computer would be computationally equivalent to a quantum computer. In the present study, the possible implications of such a striking result for the foundations of quantum mechanics and the connections between classicality and quantumness are explored. To this purpose, a model for fundamental particles that interact in physical space exchanging carriers of momentum and energy is considered. Every particle is then supplemented with an information space in which a probabilistic classical Turing machine is stored. It is analysed whether, through the action of Darwinian evolution, both a classical algorithm coding the rules of quantum mechanics and an anticipation module might plausibly be developed on the information space from initial random behaviour. The simulation of a CTC on the information space of the particle by means of the anticipation module would imply that fundamental particles, which do not possess direct intrinsic quantum features from first principles in this information-theoretic Darwinian approach, could however generate quantum emergent behaviour in real time as a consequence of Darwinian evolution acting on information-theoretic physical systems.

In this work, two plasmonic structures with two different periodic nanostructures (nanodisk and nanostrip arrays) separated from the gold layer by an ultrathin dielectric Al2O3 layer are proposed, and their optical properties are simulated as 3-dimensional models using COMSOL Multiphysics software tool. The optical responses, such as the amplification of the electric field and the scattering, absorption and extinction cross sections of the two structures, are investigated and compared. The results show that both structures show strong field enhancement in their gap layer, and the structure with the periodic array of metal nanodisks shows stronger field enhancement and larger absorption, extinction, and scattering cross sections in its dipole resonance wavelength, which is defined as a bright plasmonic mode. In addition, some weaker resonant modes are observed for both structures and the reason for their generation is dis-cussed. The analysis of different possible modes in such structures is crucial for their application in various fields.

This paper proposed a three-layer distributed simulation network architecture: 1. Distributed virtual simulation network, 2. Perception and control sub-network, and 3. Collaborative communication service network. This simulation architecture runs on a distributed platform. The platform can provide a unique virtual scenario and several simulation services to verify the individual robot system's basic perception, control, and planning algorithms and the distributed collaborative algorithms of heterogeneous multi-robot systems. Furthermore, we designed a simulation experiment scenario for classical heterogeneous robot systems such as unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs). At last, We gave a rough estimation model of the bandwidth.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

This research introduces a pioneering solution to the challenges posed by gastrointestinal tract (GI) cancer in radiation therapy, focusing on the imperative task of precise organ segmentation for minimizing radiation-induced damage. GI imaging has historically used manual demarcation, which is laborious and uncomfortable for patients. We address this by introducing the ResECA-U-Net deep learning model, a novel combination of the UNet and ResNet34 architectures. Furthermore, we further augment its functionality by incorporating the Efficient Channel Attention (ECA-Net) methodology. By utilizing data from the UW-Madison Carbone Cancer Centre, we carefully investigate several image processing techniques designed to capture critical local characteristics. With its foundation in computer vision concepts, the ResECA-U-Net model is excellent at extracting fine details from GI images. Sophisticated metrics such as intersection over union (IoU) and the dice coefficient are used to evaluate performance. Our study's outcomes demonstrate the effectiveness of the suggested method, yielding an impressive 96.27% Dice coefficient and 91.48% IoU. These results highlight the significant contribution that our strategy has made to the advancement of cancer therapy. Beyond its scientific merits, this work has the potential to significantly enhance cancer patients' quality of life and provide better long-term outcomes. Our work is a significant step towards automating and optimizing the segmentation process, which can potentially change how GI cancer is treated completely.

In this paper, the boiling flow inside a nanochannel with 700000 argon particle has been simulated by molecular dynamics (MD) simulation. This approach has been employed to analysis the superheated flow and its heat transfer pattern as well. For all simulations an external thrust force varying from 1 PN to 12 PN is exerted on inlet nanoparticles along the channel to have the forced annular boiling flow. Computations reveal that saturation condition and superheat degree have significant impacts on the liquid-vapor interface. Furthermore, because of the major influence of surface tension throughout a nanochannel, the x-velocity of liquid film and vapor core has not considerable fluctuations and stay smooth. All provided results show the behaviors completely similar to the available outcomes in the literature.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

The Vu Gia - Thu Bon River Basin (VG-TB) is confronting numerous challenges related to water security (WS), particularly in the face of the impacts of climate change. These challenges manifest in salinity intrusion, altered rainfall patterns, and reduced water supply in downstream areas. To assess the current state of water security in the basin, the study employed statistical analysis methods, Process Analysis Method (PAM), SMART, and Analytic Hierarchy Process (AHP) to develop a comprehensive Assessment Framework for Water Security (AFWS) in the VG-TB. The AFWS encompasses five key dimensions, 17 indicators, and 28 variables, aligning with the UN-Water definition of water security and addressing the Sustainable Development Goal 6 (SDG6) criteria for global water sustainability. It also adheres to the Asian Development Bank's (ADB) approach to water security assessment as outlined in the Asian Water Development Outlook (AWDO) reports. This allows for the computation of a comprehensive Water Security Index (WSI) for specific regions, serving as a foundation for decision-making and policy formulation aimed at enhancing water security in the context of climate change and facilitating sustainable basin development in the future.

Agricultural greenhouse is largely answered in the agricultural sphere, despite the shortcomings it has, including overheating during the day and night cooling which sometimes results in the thermal inversion mainly due to its low inertia. The glasshouse dressed chapel is relatively more efficient than the conventional tunnel greenhouse. Its proliferation on the ground is more or less timid because of its relatively high cost[14-22]. Agricultural greenhouse aims to create a favorable microclimate to the requirements of growth and development of culture, from the surrounding weather conditions, produce according to the cropping calendars fruits, vegetables and flower species out of season and widely available along the year. It is defined by its structural and functional architecture, the quality thermal, mechanical and optical of its wall, with its sealing level and the technical and technological accompanying[12-13]. The greenhouse is a very confined environment, where multiple components are exchanged between key stakeholders and them factors are light, temperature and relative humidity[8]. This state of thermal evolution is the level sealing of the cover of its physical characteristics to be transparent to solar, absorbent and reflective of infrared radiation emitted by the enclosure where the solar radiation trapping effect otherwise called "greenhouse effect" and its technical and technological means of air that accompany. The socio-economic analysis of populations in the world leaves appear especially the last two decades of rapid and profound transformations These changes are accompanied by changes in eating habits, mainly characterized by rising consumption spread along the year[14]. To effectively meet this demand, greenhouse-systems have evolved, particularly towards greater control of production conditions (climate, irrigation, ventilation techniques, CO2 supply, etc ...). Technological progress has allowed the development of greenhouses so that they become increasingly sophisticated and of an industrial nature (heating, air conditioning, control, computer, regulation, etc ...). New climate driving techniques have emerged, including the use of control devices from the classic to the use of artificial intelligence[10-11] such as neural networks and / or fuzzy logic, etc... As a result, the greenhouse growers prefer these new technologies while optimizing the investment in the field to effectively meet the supply and demand of these fresh products cheaply and widely available throughout the year.

The fish supply chain (FSC) industry faces a significant challenge in terms of maintaining fish quality and authenticity throughout the chain. The main goal of modern FSC systems is tracking and tracing the fish product at each stage, from harvester to end customer, as well as assessing its quality and authenticity. Integrating FSC with new technologies, such as Blockchain (BC), Big Data, Artificial intelligence (AI), and Internet of Things (IoT), enhances fish product traceability, authenticity, visibility, and security. We propose a BC-based FSC framework that follows a layered architecture consisting of a SC layer, an IoT layer, and a BC layer. We integrate a new AI-based hand-held device, a Quality, Adulteration & Traceability (QAT) device, that can identify fish species and assess fish quality. We leverage the key features of BC and smart contracts, deployed over the Ethereum platform for the proposed framework integrated with QAT technology. Extensive validation of smart contracts is conducted to prove its practical feasibility.

This research presents a comprehensive framework for efficiently generating forest fire datasets from Google Earth Engine data sources. The primary contribution of this work lies in providing a methodology to swiftly extract forest fire factors without the need for permissions or access to private datasets, rendering the dataset openly accessible and shared without barriers. Furthermore, given that the remote sensing data used is a global dataset, it can be applied in any region without restrictions. In this study, Peninsular Malaysia is chosen as a case study to demonstrate the framework's effectiveness. The generated dataset includes essential variables including the climate and environment, landcover, topography, and anthropogenic factors facilitating the analysis of fire occurrences. The methodology empowers data scientists, enabling them to leverage their analytical skills on the extracted dataset without requiring specialized remote sensing knowledge. Additionally, this study also showcases the adoption of large language models, specifically GPT-4 with the Noteable plugin, as a tool for conducting preliminary analyses on the generated dataset. Sample analyses reveal that several key features, including the KBDI, LST, PDSI, climate water deficit, and precipitation, significantly impact forest fire occurrences in Peninsular Malaysia. Despite the successful application of the GPT-4 with Noteable plugin, certain limitations and challenges are identified, highlighting the necessity for further validation of the tool's applicability and limitations. This study encourages future research to (1) adopt the proposed framework in other regions, (2) explore more detailed analyses encompassing all variables, and (3) leverage machine learning for advanced forecasting.

Direct and indirect effects after mine operations cease must ideally be subject to perpetual monitoring routines in order to detect possible risks or avoid adverse effects on the surrounding ecosystems at an early stage. In this contribution, mining subsidence lakes created inside the nature reserve Kirchheller Heide and Hilsfeld Forest are subjected to analysis for a long-term monitoring scheme. For this purpose, we employ high-resolution unmanned aerial system (UAS)-based multispectral and thermal mapping tools to provide a fast, non-invasive and multitemporal environmental monitoring method. Specifically, we propose to monitor vegetation evolution through multispectral analysis, biotypes identification using machine learning algorithms, and water surface extent detection, together with their thermal behavior. The aim of this contribution is to present the proposed workflow and first results to establish a baseline for future analyses and subsequent surveys for longterm multi-temporal monitoring

Rainfall runoff modeling has been a subject of interest for decades due to a need to understand a catchment system for management, for example regarding extreme event occurrences such as flooding. Tropical catchments are particularly prone to the hazards of extreme precipitation and the internal drivers of change in the system, such as deforestation and land use change. A model framework of dynamic TOPMODEL, DECIPHeR v1 - considering the flexibility, modularity and portability - and Generalized Likelihood Uncertainty Estimation (GLUE) method are both used in this study. They reveal model performance for the streamflow simulation in a tropical catchment, i.e. the Kelantan River in Malaysia, that is prone to flooding and experiences high rates of land use change. 32 years' continuous simulation at a daily time scale simulation along with uncertainty analysis resulted in a Nash Sutcliffe Efficiency (NSE) score of 0.42 from the highest ranked parameter set, while 25.35% of the measurement falls within the uncertainty boundary based on a behavioral threshold NSE 0.3. The performance and behavior of the model in the continuous simulation suggests a limited ability of the model to represent the system, particularly along the low flow regime. In contrast, the simulation of eight peak flow events achieves moderate to good fit, with the four peak flow events simulation returning an NSE > 0.5. Nonetheless, the parameter scatterplot from both the continuous simulation and analyses of peak flow events indicate unidentifiability of all model parameters. This may be attributable to the catchment modelling scale. The results demand further investigation regarding the heterogeneity of parameters and calibration at multiple scales.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

Change Detection (CD) of aerial images refers to identifying and analyzing changes between two or more aerial images of the same location taken at different times. The CD is a highly challenging task due to the need to distinguish relevant changes, such as urban expansion, deforestation, or post-disaster damage assessment, from irrelevant ones, such as light conditions, shadows, and seasonal variations. Many CD papers have recently been published, where most of the papers that proposed a new model contained a comparison between their proposed and state-of-the-art (SOTA) models. While many recent studies propose new deep learning (DL) models for improving CD performance, their comparative analyses are often restricted, lacking comprehensive insights into the proposed models' real-world generalizability, robustness, and performance trade-offs across diverse change characteristics. This paper presents a novel generic framework to systematically benchmark and assess DL-based CD models through three parallel pipelines: 1) cross-testing models on diverse benchmark datasets to evaluate generalization, 2) robustness analysis against different image corruptions, and 3) multi-faceted contour-level analytics evaluating detection sensitivity to change size/complexity. The framework is applied to comparatively evaluate five state-of-the-art DL-based CD models - Changeformer, BIT, Tiny, SNUNet, and CSA-CDGAN. Extensive experiments unveil each model's strengths, limitations and biases, highlighting their relative proficiencies in generalizing across data distributions, resilience to noise corruption, and discriminative capabilities for changes of varying characteristics. The proposed benchmarking framework demonstrates significant potential for guiding the selection of suitable CD models tailored to specific application requirements by comprehensively evaluating their generalizability, robustness, and detection capabilities across diverse real-world scenarios. This systematic evaluation approach can drive future research into developing more robust and versatile CD solutions aligned with practical needs.

Nowadays, unmanned vehicles are widely used in various fields. However, the safety of unmanned vehicles is directly determined by the autopilot systems, and sensor faults are a very critical factor that affects the normal operation of the autopilot systems. To efficiently and comprehensively test unmanned systems for sensor faults, this paper proposes a chip-level testing platform for unmanned vehicle autopilot systems based on FPGA hardware-in-the-loop simulation. Unlike existing testing platforms, the introduction of FPGA technology allows us to achieve nanosecond real-time simulation frequency, thus realizing chip-level simulation of sensors and black-box automated testing. Firstly, we propose a set of general platform and modeling methods, and the paper presents a detailed application of the four most common necessary sensors in autopilot systems as examples. Secondly, we propose for the first time a chip-level fault testing method for unmanned systems, and build a test platform with a quadrotor vehicle, the PX4 software platform, and the Pixhawk4 hardware platform as examples. Finally, the experimental results verify that the testing platform proposed in this paper can adapt to various autopilot systems and has high simulation test reliability.

Energy consumption modelling is of critical importance for improving energy efficiency in the drive towards sustainable manufacturing. Modern manufacturing processes and machine tools are very complex as they involve interplay of several advanced technologies. Therefore, energy modelling of modern machine tools is a complex multi-disciplinary task. This paper proposes a systematic and practical framework to choose the appropriate modelling approach for a given industrial problem. The framework was validated by applying it to diverse industrial scenarios.

Carbon Capture and Storage (CCS) stands as a pivotal technological stride toward a sustainable future, with the practice of injecting supercritical CO2 into subsurface formations having already been an established practice for enhanced oil recovery operations. The overarching objective of CCS is to protract the operational viability and sustainability of platforms and oilfields, thereby facilitating a seamless transition towards sustainable practices. This study introduces a comprehensive framework for optimizing well placements in CCS operations, employing a derivative-free method known as Bayesian optimization. The development plan is tailored for scenarios featuring aquifers devoid of flow boundaries, incorporating production wells tasked with controlling pressure buildup and injection wells dedicated to CO2 sequestration. Notably, the wells operate under group control, signifying predefined injection and production targets and constraints that must be adhered to throughout the project’s lifespan. As a result, the objective function remains invariant under specific permutations of the well locations. Our investigation delves into the efficacy of Bayesian optimization under the introduced permutation invariance. The results reveal that it demonstrates critical efficiency in handling the optimization task extremely fast. In essence, this study advocates for the efficacy of Bayesian optimization in the context of optimizing well placements for CCS operations, emphasizing its potential as a preferred methodology for enhancing sustainability in the energy sector.

: Suicide is a serious public health problem, with a global mortality rate of 1.4% of all deaths worldwide, and the leading cause of unnatural death in Spain. The use of clinical simulation has proven to be a beneficial tool in the training of nursing students. Such experiences allow them to develop cognitive and affective skills that are fundamental for the detection of warning signs and use of interventions in cases of people who want to take their own lives. Working in a mental health environment can be difficult for nursing students; therefore, the purpose of this study was to explore the perceptions of nursing students on the approach, management and intervention of suicidal crisis through clinical mental health simulation. Methods: qualitative descriptive phenomenological study through focus groups and reflective narratives in a sample of 45 students. A thematic analysis was performed using ATLAS-ti. Results: After the analysis, three themes were obtained: (a) management and handling of emotions (b) identification of suicide motives (c) intervention in suicidal crisis. Discussion: Clinical simulation in mental health allows students to exercise clinical judgment reasoning, detect warning signs for a better treatment approach, and provide tools for effective intervention and management of patient care. The results of this study indicate that nursing students face challenges in approaching mental health clinical simulation due to lack of prior exposure.

We present detailed models at the hydrodynamics and decoherence phenomena observed in ideal quantum gases. The model is expressed in terms of a quantum field theory, where the action involves both hydrodynamic and decoherence terms. The density-current relation is derived, and the current Green function is introduced. The effective action for two fields is presented, and the physical field is defined in terms of the bare action. Identities such as CTP symmetry, transposition, and the Ward identity are discussed. The Green function and its inverse for different components are also explored. These notes provide a comprehensive understanding of the theoretical framework for studying the hydrodynamics and decoherence of ideal quantum gases.

IntroductionParamedicine is a domain of practice and health profession that specialises in the provision of health and social care across a range of settings including, but not limited to, emergency and primary care. Paramedics work in a variety of clinical settings such as paramedics services, hospitals, and clinics, in the community as well as non-clinical roles, such as education, leadership, policy work, public health and research. A previous competency framework for paramedics in Canada had become increasingly poorly aligned with contemporary practice. We sought to develop a competency framework that represents contemporary paramedic practice in Canada. MethodsThis project was guided by a conceptual framework informed by systems thinking and used a six-step model for developing competency frameworks. We engaged paramedics from across Canada in working groups to explore various contexts of paramedic practice. We gathered data using multiple methods and coded this data into activity statements. We grouped these statements and developed or expanded corresponding professional activities through five drafts of the framework from 2022 to 2024. A technical committee reviewed and edited the draft framework throughout the process, culminating in a public review period from January to March 2024, and a subsequent final version of the National Competency Framework for Paramedics (NCFP). ResultsThe National Competency Framework for Paramedics reflects contemporary paramedic practice in Canada. It describes the professional activities of paramedics organised under five domains - Person-Centred Care; Collaborative Care; Safe Care; Self-Care; and Professional Care. Paramedics perform these activities across multiple contexts of practice by enacting a variety of roles depending on the event. Discussion and conclusion By exploring the variety of practice contexts and the expectations of paramedics across Canada, the NCFP provides a holistic, contemporary description of paramedic practice in Canada, providing a foundation for professional practice in a variety of settings. The five domains provide a comprehensive representation of paramedic practice helping to ensure care is ultimately and sufficiently aligned with the needs of the community and settings in which paramedics can practice. The NCFP can be used to inform education programs to better prepare paramedics for complex, interprofessional health and social care practice now and as practice continues to evolve.

Artificial intelligence (AI) systems are poised to become deeply integrated into society. If developed responsibly, AI has potential to benefit humanity immensely. However, it also poses a range of risks, including risks of catastrophic accidents. It is crucial that we develop oversight mechanisms that prevent harm. This article outlines a framework for evaluating and auditing AI to provide assurance of responsible development and deployment, focusing on catastrophic risks. We argue that responsible AI development requires comprehensive auditing that is proportional to AI systems’ capabilities and available affordances. This framework offers recommendations toward that goal and may be useful in the design of AI auditing and governance regimes.

The Internet of Things (IoT) has become one of the most attractive domains nowadays. It works by creating a special network between physical devices such as vehicles, home equipment, and other items. In recent days, the common technologies of communication such as Wi-Fi and 2G/3G/4G cellular are insufficient for the IoT networks because they are designed to serve appliances with immense processing capabilities such as laptops and PCs. Moreover, most of these technologies are centralized and use an existing infrastructure. Currently, the new communication technologies such as Z-Wave, 6LowPAN, and Thread are dedicated to the IoT and have been developed to meet its requirements. These technologies can handle many factors such as range, data requirements, security, power demands, and battery life. Nevertheless, the security issues in IoT systems have major concerns and matters because vulnerabilities in such systems may result in fatal catastrophes. In this paper, an enhanced IoT security framework for authentication and authorization is proposed and implemented to protect the IoT protocols from different types of attacks such as man-in-the-middle attack, reply attack, and brute force attack. The proposed framework combines an enhanced token authentication that has identity verification capabilities and a new sender verification mechanism on the IoT device side based on time stamp, which in turn can mitigate the need for local identity verification methods in IoT devices. The proposed IoT security framework is tested using security analysis with different types of attacks compared with previous related frameworks. The analysis shows the high capability of the proposed framework to protect IoT networks against many types of attacks compared with current available security frameworks. Finally, the proposed framework is developed using Windows application to simulate the framework phases, check its validity through the real network, and calculate the payload time is adds.

Effective water resources management requires assessments of water availability within a framework of complex institutions and infrastructure employed to manage extremely variable stream flow shared by numerous often competing water users and diverse types of use. The Water Rights Analysis Package (WRAP) modeling system is fundamental to water allocation and planning in the state of Texas in the United States. Integration of environmental flow standards into both the modeling system and comprehensive statewide water management is a high priority for continuing research and development. The public domain WRAP software and documentation are generalized for application any place in the world. Lessons learned in developing and implementing the modeling system in Texas are relevant worldwide. The modeling system combines: (1) detailed simulation of water right systems, interstate compacts, international treaties, federal/state/local agreements, and operations of storage and conveyance facilities; (2) simulation of river system hydrology; and (3) statistical frequency and reliability analyses. The continually evolving modeling system has been implemented in Texas by a water management community that includes the state legislature, planning and regulatory agencies, river authorities, water districts, cities, industries, engineering consulting firms, and university researchers. The shared modeling system contributes significantly to integration of water allocation, planning, system operations, and research.

The mHealth is a term that is used for mobile health supported by smart devices such as mobile phones, tablets, and wearable smart devices, etc. The smart devices strengthen the efficiency and effectiveness of interaction with patients, physicians, and specialists. Patients nowadays would like to be intimately involved in their diagnosis as well as to make more informed decisions concerning their care. It has begun to measure the success of the quality of treatment. This was a reason that patients trust mHealth to provide them with consistency in their communications with the physicians. Most wireless strategies do not measure up to this standard so that patient engagement ultimately ended up decreasing. The blockchain can boost mHealth through storing and sharing electronic data securely and transparently. It can enhance the accessibility of patient information in real-time. The Internet of Things (IoT) provides a unique identification number to every connected device such as mobile devices, medical devices, and wearable devices. This framework uses the blockchain and IoT technologies together to provide quick help to the patients, monitor remotely, reduce the cost and unnecessarily hospitalization physically and find the real diagnosis. In order to increase patient involvement, mHealth framework with blockchain and IoT technologies has built with the key objective of providing patients with full information on their treatment and diagnosis.

Flooding is one major environmental problem facing urban cities causing varying degree of damages to properties and disruptions to socio-economic activities. Nigeria is the most populated African country and Kano metropolis is the second largest urban center in Nigeria and the most populated in Northern Nigeria. The aim of the paper is to conduct flood risk assessment of Kano metropolis. The city is divided into two hydrological basins; Challawa and Jakara Basins. Flood frequency analysis for 2 to 100-year return periods were carried out for both the basins using Log-Pearson Type III distribution and flood inundation and hazard mappings were carried out. Social vulnerability to flood of both basins were carried out using MOVE framework. Assessment of flood risk were carried out using map algebra spatial analyst tool in ArcGIS 10.7. The result shows that an area of 50.91 and 40.56 km2 were vulnerable to a 100-year flood. The flood risk map for the two basins show that 10.50 km2 and 14.23 km2 of land in Challawa and Jakara basins respectively are affected by the risk of a 100-year flood out of which 11.48 km2 are built-up area. As the city is densely populated, with a population density of well over 20,000 persons per square kilometer in the highly built-up locations, this means that much more than 230,000 persons will be affected by the flood risk in the two basins

The objective of this paper is to investigate the debonding behavior of the interface between continuously and discontinuously fiber reinforced thermoplastics using the climbing drum peel test. The study emphasizes the importance of considering different climatic boundary conditions due to the properties of thermoplastics. Specimens with varying moisture contents are prepared and tested. It is observed that an increase in moisture content initially results in a higher fracture surface energy being required to separate the two materials, but a further increase results in a decrease of the required energy. The study presents an explanatory model of increasing plasticization of the polymer due to increased polymer chain mobility, which results in more deformation energy being required to propagate the crack. The experiment is also modeled numerically for the first time with cohesive surfaces, which successfully reproduces the force-displacement curve in the experiment.

Sources are classified into two depending upon the factor of reviving. These sources, which cannot be revived into their original shape once they are consumed, are considered as nonrenewable energy resources, i.e., (coal, fuel) Moreover, those energy resources which are revivable to the original condition even after being consumed are known as renewable energy resources, i.e., (wind, solar, hydel) Renewable energy is a cost-effective way to generate clean and green electrical energy Now a day’s majority of the countries are paying heed to energy generation from RES Pakistan is mostly relying on conventional energy resources which are mostly nonrenewable in nature coal, fuel is one of the major resources, and with the advent of time their prices are increasing on the other hand RES have great potential in the country with the deployment of RES greater reliability and an effective power system can be obtained In this thesis, a similar concept is being used and a hybrid power system is proposed which is composed of intermixing of renewable and nonrenewable sources The Source side is composed of solar, wind, fuel cells which will be used in an optimal manner to serve load The goal is to provide an economical, reliable, uninterruptable power supply. This is achieved by optimal controller (PI, PD, PID, FOPID) Optimization techniques are applied to the controllers to achieve the desired results. Advanced algorithms (Particle swarm optimization, Flower Pollination Algorithm) will be used to extract the desired output from the controller Detailed comparison in the form of tables and results will be provided, which will highlight the efficiency of the proposed system.

The aim of this work is to introduce a mathematical model representing the evolution of the temperature in a vegetation cover and the ground underneath it. Vegetation, and its interaction with soil, plays a very important role in the protection of soil surface from the action of sun and precipitations. A reduction in the vegetated mass increase the risk of desertification, soil erosion or surface runoffs which which can give rise to soil loss and sediment retention. These processes can favour climate change and global warming, which are major concerns nowadays. The mathematical model presented takes into account the main processes involved in vegetation cover and the interaction with the soil, among which, we can mention the Leaf Area Index, which is a dimensionless quantity defined as the one-sided green leaf area per unit ground surface area, or albedo and co-albedo which are clearly influenced by the vegetation. It is also considered a nonlinear heat capacity in the soil which incorporates the latent heat of fusion, when the phase change takes place. The numerical technique used to solve the mathematical model is based on a finite volume scheme with Weighted Essentially Non Oscillatory technique for spatial reconstruction and the third order Runge-Kutta Total Variation Diminishing numerical scheme is used for time integration. Some numerical examples are solved to obtain the distribution of temperature both in the vegetation cover and the soil.

Biometric based access control system acts as a weapon against the challenges for reliable authentication mechanism. Although there are many advantages of biometric system, still it is vulnerable to attacks, which decline its security. This leads to propose a new approach to address these open issues and challenges for biometric data security. Smart card have been already used in past with various degree of success to store biometric credentials. Match-on-card biometric framework locks the biometric data inside the microcontroller of the smart card, which leads to minimal risks if card is lost or stolen. It is fast and accurate, balancing security and convenience by never exchanging user data outside the system of smart card and performs fingerprint enrollment as well as matching within a tamperproof environment of smart card.

NS-3 is one of the most used Network Simulators because it includes different modules, applications and protocols to simulate a wide range of network. Since new proposals usually involve a large number of simulations, a procedure to automatize the simulation process and extract statistics is very useful. "Statistical Framework" (SF) is an important module of NS-3 because it fulfills this need. SF allows us to collect simulation data and obtain statistical reports for NS-3. In this report, we present a detailed description of statistical framework module and two useful examples of its configuration.

The growth in the Internet of Things (IoT) devices in the healthcare sector enables the new era of the Internet of Medical Things (IoMT). However, IoT devices are susceptible to diverse cybersecurity attacks and threats that lead to negative consequences. Cyberattacks can harm not just the IoMT devices being used but also human life. Currently, several security solutions are proposed to enhance the security of the IoMT, which uses machine learning (ML) and blockchain. ML can be used to develop detection and classification methods to identify cyberattacks targeting IoMT devices in the healthcare sector. In addition, blockchain technology enables a decentralized approach to the healthcare system and eliminates some disadvantages of a centralized system, such as a single point of failure. This paper proposes a resilient security framework integrating a Tri-layered Neural Network (TNN) and blockchain technology in the healthcare domain. The TNN detects anomalies in data measured by medical sensors to find fraudulent data. Therefore, cyberattacks are detected and discarded from the IoMT system before data is processed at the fog layer. In addition, a blockchain network is used in the fog layer to ensure that the data is not altered, boosting the integrity and privacy of the medical data. The experimental results show that the TNN and blockchain models produce the expected result. Furthermore, the accuracy of the TNN model reached 99.99% on the F1-score accuracy metric.

The rapid integration of Information and Communication Technology (ICT) is transforming the traditional electrical grid into a {\em Smart Grid}. Smart grids enable two-way communication and improved monitoring and control between utilities and customers. However, due to its heterogeneous nature, public exposure, and weak security at low-powered devices, the Smart Grid has vulnerabilities to various malicious threats, adversaries, and cyber attacks, which may affect cost and service availability. Additionally, when the systems' confidentiality, integrity, or availability are compromised, the resulting fallout can threaten national security and have cascading effects on human lives. Given the extreme consequences of an attack, smart-grid technology must be thoroughly tested for correct operation and security {\em before} it is deployed. As a result, vulnerability testing of smart grids, not only for correctness but for security purposes, has been the subject of numerous studies by academics, government agencies, and private companies. This paper reviews the vulnerabilities associated with the smart grid and spotlights simulation as the vulnerability testing methodology conducted in recent pertinent research works. It also presents various security aspects of the smart grid, including grid applications, system and network infrastructure and components, cyber threats and attacks, simulation, and different mitigation techniques. Finally, we analyze the gaps in the current research works, focusing on simulation. We briefly present a real-time simulation testbed that mimics customer behaviour and integrates hardware in the loop to apply attack methods, analyze vulnerabilities and risk mitigation associated with the smart grid system, and propose future work to improve the current framework.

Spectrometers have a wide range of applications ranging from optical to non-optical spectroscopy. The need for compact, portable, and user-friendly spectrometers has been the pivot of attention from small laboratories to the industrial scale. Here, the Czerny Turner configuration-based optical spectrometer simulation design is carried out using ZEMAX OpticStudio. A compact and low-cost optical spectrometer in the visible range has been developed by using diffraction grating as a dispersive element and USB-type WebCAM CCD (Charge-coupled device) as a detector instead of an expensive commercial diffraction grating and detector. Using National Instruments LabVIEW, data acquisition, processing, and displaying techniques are made possible. We have employed different virtual images in LabVIEW programs to collect the pixel-to-pixel information and wavelength-intensity information from the image captured using the WebCAM CCD. Finally, we have shown that the OpticStudio-based spectrometer and experimental measurements of the developed spectrometer are in good agreement.

Air corridors are an integral part of the advanced air mobility infrastructure. They are the virtual highways in the sky for transportation of people and cargo in the controlled airspace at an altitude of around 1000 ft. to 2000 ft. above the ground level. This paper presents fundamental insights into the design of air corridors with high operational efficiency as well as zero collisions. It begins with the definitions of air cube, skylane or track, intersection, vertiport, gate, and air corridor. Then, a multi-layered air corridor model is proposed. Traffic at intersections is analyzed in detail with examples of vehicles turning in different directions. The concept of capacity of an air corridor is introduced along with the nature of distribution of locations of vehicles in the air corridor and collision probability inside the corridor are discussed. Finally, the results of simulations of traffic flows are presented.

Differential equation models to understand interaction between plant and nutrient solution are presented. The root cells selectively emit H+ ions with active transport consuming ATPs to establish electrical gradient along the cell membrane. It establishes electrical field with Nernst potential to make positively charged ions outside the cell membrane flow into the root cell. Anion influx is also modulated by H+ ion concentration because plant root cell absorbs negatively charged particles with symport. If an anion collides with H+ cell to make net charge as neutral, at symport channel, it can flow through. In this paper, mathematical models for cation and anion absorption are introduced. Cation absorption model was induced from Ohm's law combined with Goldman's equation. Anion absorption model is similar to chemical reaction rate model. Both models have physiological terms influenced by gene expression pattern, species or phenotypes. Cation model also includes terms for ion's kinetic and electrical properties, growth of plant and interaction between the root and the surroundings. Simulation for 20 different sets of coefficients showed that the physiology-related coefficient has important role on nutrition absorption tendencies of plants.

We introduce a mission design for an interstellar expedition to nearby earth-like exoplanets, which our analysis determined to be Tau Ceti and Gliese 667C, at the time of analysis in 2013. We review the research problems in propulsion and AGI that must be addressed to launch an AI guided interstellar probe within 100 years. We propose a new semi-autonomous agent approach for intelligent control of the spacecraft. We introduce the concept of a semi-autonomous agent as having built-in safety guarantees that constrain operation. An autonomous agent case study is presented formulating the objective, constraints, AGI implementation of the agent based on Solomono's Alpha architecture, and adding speci city. We discuss the training required to reach human-level and trans-sapient levels of intelligence which corresponds to an entire crew of AI experts specialized in elds such as astrophysics, astromechanics, astrobiology, quantum physics, computer science, molecular biology, and so forth. We project the feasibility of the human-level AI technology based on empirical ndings in neuroscience, and nd that it should be feasible by 2030. We analyze Solomono's in nity point hypothesis in light of Koomey's law about energy eciency of computing and nd that the trends in 2013 indicated an early singularity by 2035, which implies that we might encounter physical bottlenecks which will decelerate computing technology improvements signi cantly. We recommend thus year 2040 for launching the probe by which date other required technologies will have been developed. We discuss the scenario of a virtual crew made of brain simulations, which is a bio-information based AI approach. We detail the subsystems of command and control, communication, scienti c instrumentation, power, propulsion, navigation, and shielding. We propose a variation of ICAN-II/AIMStar propulsion which uses a positron source instead of anti-protons to initiate micro-fusion reactions. We combine the positron initiated fusion pulse propulsion scheme with a miniaturized version of the Daedelus fusion thruster obtaining high performance. We derive two mission pro les one for fusion pulse propulsion, and the yet hypothetical Q-Thruster. Fusion thruster requires 132.2 years for Tau Ceti, and 233.2 years for Gliese 667C, while Q-Thruster takes only 42.3 years for Tau Ceti, and 62.5 years for Gliese 667C. We also discuss extended roles for intelligent interstellar probes such as self-reproduction via nanotechnology, refueling, construction, robotic bodies, and transmission of brain simulations.

Sustainability is pivotal in the urban transformation strategy in order to reach more resource-efficient, resilient and smarter cities. The goal of being a sustainable city should drive the decisions for city interventions. Nonetheless, impacts need to be quantified, lacking of standard and/or common methodologies that could be replicable across multiple cities. There exist many initiatives aiming at defining indicators and assessment procedures, but without convergence in the definition of terms and application methodologies, making complex its real implementation. Within mySMARTLife project (GA#731297), a KPI-driven evaluation framework is defined with the aim of covering the multiple pillars of a city (i.e. energy, mobility, citizens, economy) in a holistic way. This methodology also defines the concepts and terms to guide urban planners and/or experts at time of implementing the framework in a specific city. The evaluation framework has been deployed in the three cities of Nantes, Hamburg and Helsinki and some lessons learnt have been extracted, such as the necessity of providing a definition of measurement boundary to avoid interpretations. Thanks to a co-creation strategy, the main difficulties and issues from the cities have been taken into consideration for increasing the replicability.

This paper shows that by applying the Nyquist-Shannon sampling theorem, the spatial and temporal resolution of a simulation can be no more than half the resolution of the simulating reality. This has significant implications for not only the values of the observables in the simulation but also its physical laws. This progressive halving of nested simulations coupled with the minimum resolution compatible with the production of a simulation also sets a limit to the nestedness of a lineage of simulations (it is by no means infinite). The limit of nestedness is then used to calculate the probability that we are living in a simulation assuming a single base reality. This will be shown to be significantly lower than popular expectation. A Kardashev-like scale, with three variants, is also developed to gauge the technological advancement of a civilization in relation to the extent to which it can extract information from space and time.

This study examines the performance of the Indian Monsoon Data Assimilation and Analy-sis (IMDAA) in predicting five extremely severe cyclonic storms (ESCS) over the Bay of Bengal. The Advanced Research version of the WRF (ARW) model is utilized for this analysis over the last two decades. The initial and lateral boundary conditions are derived from the IMDAA datasets with a horizontal resolution of 0.12° × 0.12°. Five ESCSs from the past two decades are considered: Sidr 2007, Phailin 2013, Hudhud 2014, Fani 2019, and Amphan 2020. The model is integrated up to 96 hours using double nested domains of 12 km and 4 km. Model performance is evaluated using the 4 km results, compared with available observational datasets, including the best-fit data from the India Meteorological Department (IMD), The Tropical Rainfall Measuring Mission (TRMM) satellite, and Doppler Weather Radar (DWR). The results indicate that IMDAA provides accurate forecasts for ESCSs Fani, Hudhud, and Sidr in terms of track, intensity, and mean sea level pressure, aligning well with IMD observational datasets. However, Sidr's track deviates more from the observations. The calculated mean absolute maximum sustained wind speed errors range from 8.4 m/s to 10.6 m/s from day-1 to day-4, while mean track errors range from 114 km to 496 km during the same period. Statistical analysis, including bias, mean error, and standard deviation, underscores the significance of ESCS prediction. The discussion also covers rainfall prediction, maximum reflectivity, and the associated structure of the storms.

Sensor fusion algorithms and models have been widely used in recent times. Although research evidence has informed the use of sensor fusion models in diverse applications, there is room for improvement, especially in home-based health monitoring applications which require less supervision and technical knowledge of users. The present work compares data mining-based fusion software packages such as RapidMiner Studio, Anaconda, Weka, and Orange, and proposes a data fusion framework suitable for in-home applications. 574 privacy-friendly (binary) images and 1,722 datasets gleaned from thermal and Radar sensing solutions respectively, were fused using the software packages on instances of homogeneous and heterogeneous data aggregation. Experimental results indicated that the proposed fusion framework achieved an average Classification Accuracy of 84.7% and 95.7% on homogeneous and heterogeneous datasets respectively, with the help of data mining and machine learning models such as Naïve Bayes, Decision Tree, Neural Network, Random Forest, Stochastic Gradient Descent, Support Vector Machine, K-Nearest Neighbours and CN2 induction. Further evaluation of the sensor data fusion framework based on cross validation of features indicated average values of 94.4% for Classification Accuracy, 95.7% Precision and 96.4% for Recall.

Current bridge inspection practices rely on paper-based data acquisition, digitization, and multiple conversions in between incompatible formats to facilitate data exchange. This practice is time-consuming, error-prone, cumbersome, and leads to information loss. One aim for future inspection procedures is to have a fully digitized workflow that achieves loss-free data exchange, which lowers costs and offers higher efficiency. On the one hand, existing studies proposed methods to automatize data acquisition and visualization for inspections. These studies lack an open standard to make the gathered data available for other processes. On the other hand, several studies discuss data structures for exchanging damage information through out different stakeholders. However, those studies do not cover the process of automatic data acquisition and transfer. This study focused on a framework that incorporates automatic damage data acquisition, transfer, and a damage information model for data exchange. This enables inspectors to use damage data for subsequent analyses and simulations. The proposed framework shows the potentials for a comprehensive damage information model and related (semi-)automatic data acquisition and processing.

Background: Recent disasters have demonstrated gaps in employers’ preparedness to protect employees and promote their well-being in the face of emergencies and disasters affecting the workplace and their communities. Total Worker Health (TWH), a comprehensive perspective developed by the National Institute for Occupational Safety and Health, is a helpful framework for addressing employer preparedness. It includes attention to health and safety at work, and the promotion of the health and well-being of the employee in the context of social determinants of health, such as work-life balance. Methods: TWH concepts, including the domains of TWH and the TWH Hierarchy of Controls, were investigated for their relevance to protecting employees and promoting their well-being during and after crises such as weather disasters, pandemics, and acts of terrorism. Building upon TWH concepts, an employer preparedness framework and model is proposed. Findings: The Model emphasizes upstream prevention, workplace-community linkages, social and economic impacts, and employer leadership through a cyclical planning process. Conclusions/Application to Practice: The Model can assist employers in advancing their preparedness for all hazards through self-assessment and planning agendas based upon the proposed domains.

This report presents a framework for analysing the risk of alien taxa under South Africa's National Environmental Management: Biodiversity Act of 2004, and the Alien and Invasive Species Regulations of 2014. While the report was initially designed to meet a specific South Africa need, the risk analysis processes developed can, we believe, be transferred to any specified geographic region. In outlining a series of questions related to a taxon’s likelihood of invasion and the consequences thereof, i.e. the potential impacts, the report provides a structure for collating data relevant to the process of listing taxa as well as a process for developing recommendations that is both mathematically sound, transparent, and that explicitly takes uncertainty into account. The framework is based on collating information according to international standards in biological invasions (specifically the IUCN Environmental Impact Classification of Alien Taxa Scheme, the CBD's scheme for classifying invasion pathways, and the Unified Framework for Biological Invasions proposed by Blackburn et al. 2011). The risk analysis framework is currently being implemented in South Africa in an effort to underpin national regulatory lists of invasive species.

Background: With the rapid improvement of the healthcare technologies, security and privacy of the most sensitive data, health data is at risk. Protecting patient privacy has many components, even though the data are in electronic format. Although patient privacy is thoroughly discussed in the literature, there is no study presenting all components of patient privacy protection. Methods: In this study, a complete evaluation framework is presented, as an evaluation tool, an inventory is developed, reliability and validity of the inventory is examined. Study is conducted in three phases: Conceptual framework development, inventory development and an evaluation case study. In the evaluation, fuzzy conjoint analysis is employed to handle the subjectivity and am-biguity. As the result of the evaluation, the institution is given a patient privacy protection ma-turity grade, between 1 and 5, where 1 is the worst and 5 is the best grade. Results: In the case study, XXX’s biggest hospital, employing 800 nurses, is evaluated. Half of the nurses, 400, have partici-pated in the study. Literature tells healthcare institutions do not invest enough to protect patient privacy, and the study results support this finding. Institution’s maturity grade resulted as level 2, which is bad. Conclusion: The study measures he privacy maturity with many evaluation com-ponents. Result of the evaluation explains to the patients and the public if their data is safe or not. With this maturity grade, patients have an idea about which institution to choose, public can conclude the institutions’ reliability in terms of patient privacy.

This paper integrates carrier manifolds from control theory and hybrid systems modeling to develop a novel mathematical framework for Artificial General Intelligence (AGI). Carrier manifolds represent the state space of complex AGI systems, while hybrid systems model discrete and continuous dynamics together. The proposed architecture embeds carrier manifold into GPTProX, a hybrid AI solver combining conversational AI, logic programming, and optimization.

We propose a forward-only multi-layer encoding-decoding framework based on the principle of Maximal Coding Rate Reduction (MCR$^2$), an information-theoretic metric that measures a statistical distance between two sets of feature vectors up to the second moment. The encoder directly transforms data vectors themselves via gradient ascent to maximize the MCR$^2$ distance between different classes in the feature space, resulting in class-wise mutually orthogonal subspace representations. The decoder follows a process symmetric to the encoder, and transforms the subspace feature vectors via gradient descent to minimize the MCR$^2$ distance between the reconstructed data and the original data. We show that the encoder transforms data to linear discriminative representations without breaking the higher-order manifolds, and the decoder reconstructs the data with high fidelity.

This is an article or technical note which is intended to provides an insight journey of Machine Learning Systems (MLS) testing, its evolution, current paradigm and future work. Machine Learning Models, used in critical applications such as healthcare industry[1], Automobile [2], [3] and Air Traffic control, Share Trading etc., and failure of ML Model can lead to severe consequences in terms of loss of life or property. To remediate this, developers, scientists, and ML community around the world, must build a highly reliable test architecture for critical ML application. At the very foundation layer, any test model must satisfy the core testing attributes such as test properties and its components. This attribute comes from the software engineering [5], [6], but the same cannot be applied in as-is form to the ML testing and we will tell you “why”.

In recent years, advances in science, technology, and the way in which we view our world have led to anincreasingly broad use of the term “intelligence”. As we learn more about biological systems, we find more and more examples of complex and precise adaptive behavior in animals and plants. Similarly, as we build more complex computational systems, we recognize the emergence of highly sophisticated structures capable of solving increasingly complex problems. These behaviors show characteristics in common with the sort of complex behaviors and learning capabilities we find in humans, and therefore it is common to see them referred to as “intelligent”. These analogies are problematic as the term "intelligence" is inextricably associated with human-like capabilities. While these issues have been discussed by leading researchers of AI and renowned psychologists and biologists highlighting the commonalities and differences between AI and biological intelligence, there have been few rigorous attempts to create an interdisciplinary approach to the modern problem of intelligence. This article proposes a comparative framework to discuss what we call “purposeful behavior”, a characteristic shared by systems capable of gathering and processing information from their surroundings and modifying their actions in order to fulfill a series of implicit or explicit goals. Our aim is twofold: on the one hand, the term purposeful behavior allows us to describe the behavior of these systems without using the term "intelligence", avoiding the comparison with human capabilities. On the other hand, we hope that our framework encourages interdisciplinary discussion to help advance our understanding of the relationships among different systems and their capabilities.

Cloud infrastructure provides computing services where computing resources can be adjusted on-demand. However, the adoption of cloud infrastructures brings concerns like reliance on the service provider network, reliability, compliance for service level agreements (SLAs), etc. Software-defined networking (SDN) is a networking concept that suggests the segregation of a network’s data plane from the control plane. This concept improves networking behavior. In this paper, we present an SDN-enabled resource-aware topology framework. The proposed framework employs SLA compliance, Path Computation Element (PCE) and shares fair loading to achieve better topology features. We also present an evaluation, showcasing the potential of our framework.

The explosive emergence of wireless technologies and standards, covering licensed and unlicensed spectrum bands has triggered the appearance of a huge amount of wireless technologies, with many of them coexisting in the same band. Unfortunately, the wireless spectrum is a scarce resource, and the available frequency bands will not scale with the foreseen demand for new capacity. Certain parts of the spectrum, in particular the license-free ISM bands, are overcrowded, while other parts, mostly licensed bands, may be significantly underutilized. As such, there is a need to introduce more advanced techniques to access and share the wireless medium, either to improve the coordination within a given band, or to explore the possibilities of intelligently using unused spectrum in underutilized (licensed) bands. Therefore, in this paper, we present a SDR based framework that can be employed to devise disruptive techniques to optimize the sub-optimal use of radio spectrum that exists today. Additionally, we describe two use cases for the proposed framework.

In this work, the deoxygenation of organic liquid products (OLP) obtained by thermal catalytic cracking of palm oil at 450 °C, 1.0 atmosphere, with 10% (wt.) Na₂CO₃ as catalyst, in multistage countercurrent absorber columns using supercritical carbon dioxide (SC-CO₂) as solvent, with Aspen-HYSYS process simulator was systematically investigated. In a previous study, the thermodynamic data basis and EOS modeling necessary to simulate the deoxygenation of OLP has been presented [Molecules 2021, 26, 4382. https://doi.org/10.3390/molecules26144382]. This work address a new flowsheet, consisting of 0₃ absorber columns, 10 expansions valves, 10 flash drums, 08 heat exchanges, 01 pressure pump, and 0₂ make-up of CO₂, aiming to improve the deacidification of OLP. The simulation was performed at 333 K, 140 bar, and (S/F) = 17; 350 K, 140 bar, and (S/F) = 38; 333 K, 140 bar, and (S/F) = 25. The simulation shows that 81.49% of OLP could be recovered and the concentrations of hydrocarbons in the extracts of absorber-01 and absorber-02 were 96.95 and 92.78% (wt.) in solvent-free basis, while the bottom stream of absorber-03 was enriched in oxygenates compounds with concentrations up to 32.66% (wt.) in solvent-free basis, showing that organic liquid products (OLP) was deacidified and SC-CO₂ was able to deacidify OLP and to obtain fractions with lower olefins content. The best deacidifying conditions was obtained at 333 K, 140 bar, and (S/F) = 17.

3D-printed models with high anatomic fidelity are an increasingly viable tool in simulation-based medical education. One advantage of 3D models is they provide enhanced tactile and spatial understanding of complex anatomy to develop technical skills used in minimally invasive procedures. We propose that 3D anatomical models can improve the development of Interventional Radiology vascular access skills – first described in the 1950s as the Seldinger Technique – for pre-clerkship medical students. Early adoption of 3D-printed technology in pre-clinical medical education can lead to improved student engagement and satisfaction when learning procedural techniques. This study involved creating a 3D model of the upper extremity vasculature from an anonymized CT angiogram, using it as a medical education tool for 31 pre-clinical medical students practicing the Seldinger Technique on a prefabricated venipuncture arm, and assessing student satisfaction with this form of learning. Overall, attendees responded positively to the incorporation of the 3D model in medical education to improve their anatomic understanding and application to the Seldinger Technique. These results indicate that the use of 3D models in simulation-based medical education can provide benefits to acquiring technical skills and the potential to decrease training costs without harming a patient.

In this study, Acısu Basin, which is upper side of one of the most important basins (Gediz) in Türkiye, was modelled using three types of hydrological models and three different calibration algorithms. Lumped (GR4J), semi-distributed (SWAT+), and fully distributed (mHM) hydrological models were built and integrated with Parameter Estimation Tool (PEST) which is a model independent calibration tool including various algorithms. Levenberg Marquardt (L-M), Shuffled Complex Evolution (SCE), and Covariance Matrix Adoption Evolution Strategy (CMA-ES) were selected as calibration algorithms. Calibration period was 1991-2000, and validation results were obtained for 2002-2005. The effect of model structure and calibration algorithm selection on discharge simulation was evaluated via comparison of 9 different model-algorithm combinations. Results have shown that mHM and CMA-ES combination showed the best discharge simulation performance according to NSE values (calibration: 0.67, validation: 0.60). Although statistically the model results were classified as acceptable, the pattern comparison of discharge value shows that all of the models miss the peak values in significant amounts. This problem may be related to the interventions made in 2000-2001 years interval and possible to overcome by changing the calibration and validation periods, increasing the number of iterations or using the naturalized gauge data.

This paper is focused on understanding multiscale modelling to obtain a bridge among different time and length scales of simulation techniques. These techniques are vital as it holds the potential to understand and predict the capabilities of polymer nanocomposites (PNCs). However, an appropriate approach in controlling the interfacial interaction between nanoparticle and polymer in nanocomposites structure is still needed to develop. In this review, an initial brief introduction to various trending simulation techniques has been discussed at all three levels of scale (nm, μm, mm). Later, descriptive study on fundamental issues such as thermodynamics, kinetics, mechanical properties, and morphology has been studied deeply. The multiscale modeling bridges the gaps of simulation between the different scales of models from molecular to mesoscale levels working over the broad range of length and timescale. Through the sequential, adaptive, and concurrent approaches, we can develop a system that may comprehend multiscale mode modeling adaptive resolution approach has recently added approach the molecule of the subject can shift their position freely in the domain and through this approach and studied the Brownian motion. Co-The co-current coach is also termed as handshaking path and it is linked aiming at different scale models. Covering the rigid techniques smoothly and linking them at different scales helps in normalizing the statistical behaviour.

In Differentiated Services (DiffServ) architecture, Priority Service System (PSS) plays a vital responsibility to provide Quality-of-Service (QoS) for the applications based on networks. Priority queuing systems has always been a subject of interest for analytical modelling and evaluating the performance. However, previous works have mainly focused on performing priority queuing under range dependent traffics, namely Short Range Dependent (SRD) or Long Range Dependent (LRD). Recent studies revealed that realistic traffic demonstrates a heterogeneous nature for the modern networks that provide multiple services. In this paper, the results of analytical and simulation models of dynamic priority service systems is reviewed to study the heterogeneous traffic impact on designing and performance of the systems based on networks. In this paper, the results of analytical and simulation models of dynamic priority service systems is reviewed to investigate the impact of heterogeneous traffic on the design and performance of network-based systems. Here, the time of presence of requests in limited and unlimited buffer system is restricted. If the restriction is violated, the requests will be lost. The results of experiments conducted on both models are compared and it is identified that they differ in the allowable limit (2-9) %.

Is it possible to develop a meaningful measure for the complexity of a simulation model? Algorithmic information theory provides concepts that have been applied in other areas of research for the practical measurement of object complexity. This article offers an overview of complexity from a variety of perspectives and provides a body of knowledge with respect to the complexity of simulation models. Key terms of model detail, resolution, and scope are defined. An important concept from algorithmic information theory, Kolmogorov complexity, and an application of this concept, normalized compression distance, are used to indicate the possibility of measuring changes in model detail. Additional research in this area can advance the modeling and simulation body of knowledge toward the practical application of measuring simulation model complexity. Examples show that KC and NCD measurements of simulation models can detect changes in scope and detail.

Summary: Studying biological systems generally relies on computational modeling and simulation, e.g., for model-driven discovery and hypothesis testing. Progress in standardization efforts led to the development of interrelated file formats to exchange and reuse models in systems biology, such as SBML, the Simulation Experiment Description Markup Language (SED-ML), or the Open Modeling EXchange format (OMEX). Conducting simulation experiments based on these formats requires efficient and reusable implementations to make them accessible to the broader scientific community and to ensure the reproducibility of the results. The Systems Biology Simulation Core Library (SBSCL) provides interpreters and solvers for these standards as a versatile open-source API in Java™. The library simulates even complex bio-models and supports deterministic Ordinary Differential Equations (ODEs); Stochastic Differential Equations (SDEs); constraint-based analyses; recent SBML and SED-ML versions; exchange of results, and visualization of in silico experiments; open modeling exchange formats (COMBINE archives); hierarchically structured models; and compatibility with standard testing systems, including the Systems Biology Test Suite and published models from the BioModels and BiGG databases. Availability and implementation: SBSCL is freely available at https://draeger-lab.github.io/SBSCL/.

This article is devoted to Feller's diffusion equation which arises naturally in probabilities and physics (e.g. wave turbulence theory). If discretized naively, this equation may represent serious numerical difficulties since the diffusion coefficient is practically unbounded and most of its solutions are weakly divergent at the origin. In order to overcome these difficulties we reformulate this equation using some ideas from the Lagrangian fluid mechanics. This allows us to obtain a numerical scheme with a rather generous stability condition. Finally, the algorithm admits an elegant implementation and the corresponding Matlab code is provided with this article under an open source license.

Financing frameworks for Public Private Partnerships (PPPs) are lacking in developing countries. This study develops and recommends a financing framework for water and sanitation PPP infrastructure projects in Zimbabwe. The framework model integrates the Public Private Partnership models, sources of finance for water and sanitation PPPs, and the drivers of water and sanitation PPP finance. Both the public and private sources of finance are instrumental for financing water and sanitation PPP projects. Tobit econometric models are applied on data collected from both international and domestic data banks. The time frame for the analysis is a 25-year period running from 1996 ending 2021. Capital market variables, bank market development and economic affluence drive the financing of water and sanitation Public Private Partnership infrastructure projects in Zimbabwe. The study recommends the application of the developed framework in the water and sanitation Public Private Partnership infrastructure financing policy, for developing countries.

A common problem in education has always been to get students to achieve an adequate level of motivation and engagement. Many evidences show that gamification has the potential to make learning more engaging, motivating and effective. However, it is essential to design gamified experiences thoughtfully, ensuring that they align with educational objectives and promote meaningful learning outcomes, and so the lack of established design methodologies can lead to unintended consequences.

IoTs and WSNs utilize their connectivity to enable solutions supporting a spectrum of industries in different and volatile environments. To effectively enhance the security and quality of service of networks, empirical research should take into account a variety of factors and be structured in a replicable manner. This will not only ensure scalability but also enable verification of conclusions, leading to more constructive outcomes. Cooja offers limited performance analysis capabilities of simulations, which are often extracted and calculated manually. In this paper, we introduce a framework and a toolkit that enable researchers to conduct structured and conclusive experiments considering different factors and metrics, experiment design to results analysis. Besides, this tool summarizes multiple network metrics and allows multiple scenarios. As proof of concept, this paper studies the flooding attacks on IoT and illustrates their impact on the network, leveraging the proposed framework and tools.

Human activity recognition (HAR) using wearable sensors is gaining popularity in the healthcare domain, enabling continuous monitoring and timely interventions. The conventional HAR systems are centralised and need data sharing with a server for processing and model training. However, this data sharing leads to various challenges, such as privacy concerns, increased communication and storage costs, inefficient computational algorithms, data scarcity due to unwillingness to share, and difficulty achieving high accuracy and personalised models simultaneously. To overcome these challenges, this paper introduces a privacy and energy-aware federated learning (FL) framework for model training without data sharing. The proposed scheme incorporates spiking neural networks (SNNs), which are particularly suited for resource-constrained devices due to their event-driven information processing. The key idea is to synergise the strengths of SNNs and long short-term memory (LSTM) to create a hybrid model for robust HAR. The proposed hybrid spiking LSTM (S-LSTM) model uses the LSTM as an input layer to capture temporal dependencies efficiently, followed by spiking layers that replace the typical activation using leaky integrate-and-fire neurons. We employ the combination of surrogate gradient learning and backpropagation through time (BPTT) to update the weights of SNN layers in a supervised manner. The performance of the proposed model is evaluated using two publicly available datasets for both indoor and outdoor scenarios. The results show that the proposed S-LSTM performs much better than spike convolutional neural networks (S-CNN) and simple CNN, achieving the accuracy of 97% and 87% for indoor and outdoor datasets, respectively. Personalisation, also known as fine-tuning the global model using local data, is crucial in HAR. It allows the model to adapt to individual behaviour and preferences, making predictions more accurate. The results also show that personalisation improves the performance of participants up to 9% on average. Additionally, analysis with 50% random client participation reduces communication costs by 50% with minimal impact on accuracy.

Feedback trading theory is one of the most primitive theories about financial market. But for a long time，researches and modelings on this topic are rarely seen. The model in this paper shows the effects of sentiment shocks on asset prices in a market characterized by feedback trading in the long run. We find that，generally，feedback trading will lead to cognitive bias effect and trading inducement effect. Cognitive bias effect increases with the feedback trading parameter ( FTP) . In our model，the abnormal volatility of asset prices is captured by cognitive bias effect，sentiment shock effect and trading inducement effect．

During the last few years, several approaches have been proposed to improve early warning systems for reducing rock-fall risk. In this regard, this paper introduces a Deep learning-and (IoT) based Framework for Rock-fall Early Warning, devoted to reducing the rock-fall risk with high accuracy. In this framework, the prediction accuracy was augmented by eliminating the uncertainties and confusion plaguing the prediction model. In order to achieve augmented prediction accuracy, this framework fused the prediction model-based deep learning with a detection model-based Internet of Things. In order to determine the framework’s performance, this study adopted parameters, namely overall prediction performance measures, based on a confusion matrix and the ability to reduce the risk. The result indicates an increase in prediction model accuracy from 86% to 98.8%. In addition, a framework reduced the risk probability from (1.51 ×10-3) to (8.57 ×10-9). Our results indicate the framework’s high prediction accuracy; it also provides a robust decision-making process for delivering early warning and lowering the rock-fall risk probability.

The Internet of Vehicles (IoV) is an emerging field that has attracted significant attention due to its potential to transform transportation and mobility. IoV enables the development of new services and applications that can improve transportation systems' efficiency, safety, and sustainability. However, ensuring secure and trustworthy communication among the different components of an IoV system is a critical challenge that needs to be addressed. This paper proposes a blockchain-enabled communication framework for secure and trustworthy IoV applications. The proposed framework leverages the security and decentralization features of blockchain technology to provide secure communication channels for different components of the IoV system, including vehicles, infrastructure, and service providers. The proposed framework provides an identity management system to authenticate and authorize users and devices, thereby preventing unauthorized access and data breaches. To evaluate the effectiveness of the proposed framework, we conducted experiments using a real-world IoV scenario, and the results demonstrate that the proposed framework can provide secure and trustworthy communication for IoV applications. The proposed blockchain-enabled communication framework offers a promising approach to address the security and trust challenges in IoV communication systems.

This paper presents a comprehensive and adaptive framework for orchid conservation programs illustrated with data from published and unpublished case studies. There is a specific focus on West Australian terrestrial orchids, but many of the approaches have universal relevance. Aspects of the framework include (1) setting appropriate objectives, (2) establishing effective collaborations between scientists, volunteers and regulators to fill knowledge and funding gaps, (3) use of survey and demographics data to determine extinction risks and management requirements for species, (4) effective habitat management to overcome threats such as grazing, (5) finding potential new habitats by modelling climate and site data, (6) investigating the effectiveness of pollinators and (7) using seed baiting to detect mycorrhizal fungi. The relative cost and effectiveness of different methods used to propagate orchids for translocation are compared. Methods known to be successful, in order of complexity, include placement of seed in situ, vegetative propagation, symbiotic germination in non-sterile organic matter, symbiotic germination in sterile culture, asymbiotic sterile germination and clonal division in tissue culture. These form a continuum of complexity, cost, time required, faculties needed, as well as the capacity to maintain genetic diversity and produce seedlings preadapted to survive in situ. They all start with seed collection and lead to seed storage, living collections used as tuber banks and seed orchards, as well as translocation for conservation. They could also lead to commercial availability and sustainable ecotourism, both of which are needed to reduce pressure on wild plants. Overall, there has been a strong preference to use relatively complex, expensive and time-consuming methods for orchid conservation, despite evidence that simpler approaches have also been successful. These simpler methods, which include in situ seed placement and non-sterile germination on inorganic substrates, should be trialled in combination with more complex orchid propagation methods as part of an adaptive management framework. It is essential that orchid conservation projects harness the unique biological features of orchids, such as abundant seed production and mycorrhizal fungi which are far more widespread than their hosts. This is necessary to increase the efficiency and coverage of recovery actions for the largest and most threatened plant family.

A Smart Home is characterized by the presence of a huge number of small, low power devices, along with more classical devices. According to the Internet of Things (IoT) paradigm, all of them are expected to be always connected to the Internet in order to provide enhanced services. In this scenario, an attacker can undermine both the network security and the user’s security/privacy. Traditional security measures are not sufficient, because they are too difficult to setup and are either too weak to effectively protect the user or too limiting for the new services effectiveness. The paper suggests to dynamically adapt the security level of the smart home network according to the user perceived risk level what we have called network sentiment analysis. The security level is not fixed, established by a central system (usually by the Internet Service Provider) but can be changed with the users cooperation. The security of the smart home network is improved by a distributed firewalling and Intrusion Detection Systems both to the smart home side as to the Internet Service Provider side. These two parts must cooperate and integrate their actions for reacting dynamically to new and ongoing threats. Moreover, the level of network sentiment detected can be propagate to nearby home networks (e.g. the smart home networks of the apartments inside a building) to increase/decrease their level of security, thus creating a true in-line Intrusion Prevention System (IPS). The paper also presents a test bed for Smart Home to detect and counteract to different attacks against the IoT devices,,Wi-Fi and Ethernet connections .

A deterministic quantum mechanics theory is presented in a series of papers starting with the present one. The proposed theory is shown to be consistent with the current mainstream statistical quantum theory as well as with classical physics. It produces solutions, which demonstrate that causality, physical reality, and determinism are restored and can explain in simple form concerns that are raised by results from the current mainstream statistical quantum theory. The meaning of particle- wave duality and complementarity, the possibility of a particle, like the electron, to cross through the nucleus as it does when the angular momentum of the electron is zero at the ground state of the hydrogen atom, the possibility of a point-size particle to have an “intrinsic spin”, the possibility of “quantum jumps” as the electron transitions instantaneously from one stable orbital to another without passing through the space in between the orbitals and does that at irregular time intervals, and the natural collapse of the wave function as part of the solution are some of the results that emerge from the proposed deterministic quantum mechanics theory. The phenomenon of entanglement is shown to be consistent with the proposed deterministic quantum mechanics theory. The Bohr-Schrödinger energy levels leading to the experimentally confirmed spectral lines, as well as the fine structure constant emerge directly from the solution of the equations governing theproposed deterministic quantum mechanics presented in Part II of these series of papers.

In this paper, we develop a tractable mathematical model and emulation framework for communicating information through water using acoustic signals. Water is considered as one of the most complex mediums to model owing to its vastness and variety in characteristics depending on the scenario, what kind of water-body (lakes, rivers, tanks, sea etc.) and geographical location of the water-body is considered. Our proposed mathematical model involves the concept of damped harmonic oscillators to represent the medium (water) and Milne’s oscillator technique to map the interaction between the acoustic signal and water. Wave equations formulated for acoustic pressure and acoustic wave velocity are used to characterize the travelling acoustic signal. Signal strength, phase shift and time-delay generated from the mathematical model are fed to a Simulink-based emulator framework to generate channel samples and channel impulse responses. The emulator uses wide sense stationary uncorrelated scattering (WSSUS) assumption and finite sum-of-sinusoids (SOS) with uniformly distributed phase to generate the channel samples. Using the emulator platform it is possible to generate amplitude variation profile, Doppler shift and spread experienced by any travelling signal through different underwater communication scenarios. Such an emulator platform can be used to simulate different communication scenarios, underwater network topologies, data to train different learning models and predict performance of different modulation, multiplexing, error correction and multi-access techniques for underwater acoustic communications (UWAC) systems.

With a worldwide growing concern for greenhouse gas (GHG) emissions and their impact on human health and the environment, transportation has become a central theme in mitigation, responsible for 14% of human GHG emissions. To build endurance to climate change, transportation services must adapt to the current scenario and act quickly to avert future changes. Deeply rooted changes in socio-technical systems will be necessary to achieve significant CO2 reduction and secure the well-being of future generations. This study's objective is to comprehensively review the current state of carbon mitigation in the transportation sector. This is done through a systematic literature review engrained in the socio-technical transition theory and the structural theory of contingency. Twenty-six review papers covering 2,983 original articles are selected for full-text examination concerning carbon emissions in transportation. Enablers, barriers, benefits, disadvantages and metrics in carbon emissions reduction are identified, and a comprehensive framework is built. Results provide a view of the current sustainability scenario in transportation and allow a better understanding of the factors influencing carbon emission initiatives in transportation and its outcomes.

Electrical microgrids are deemed to be the future of modern power systems. Microgrids are sophisticated, decentralized, and self-sufficient small-scale power systems consisting of various resources ranging from wind turbines, solar photovoltaics, electric vehicles, smart energy storage, and complex communication infrastructure. However, renewable energy sources such as solar photovoltaics and wind-based generators are highly intermittent, and if not appropriately planned, they can compromise the stability of the grid. Formal methods can define and analyze the functionality and behavior of any system and show if the system design is correct before the actual system is implemented. Although formal methods have been around for many years, it is surprising that little to none are utilized in the design of safety-critical electrical power systems. Currently, in modeling microgrids, few to no attempts of formalization are being used to improve the design reliability and reduce system operating costs and time. This work demonstrates how complex systems such as microgrids can be modeled elegantly using a formal specification method. In this work, the Z state-based formal specification language (Z-Method) is used to model and verify microgrid designs. In this work, 3-interconnected microgrid systems with a high penetration level of solar and wind-based renewable energy sources with plugin hybrid electric vehicles (PHEV) as battery energy storage systems (BESS) are modeled using the Z-method. To the best of authors, the knowledge presented formal method is one of the first reported attempts in modeling microgrid communities using Software Engineering formalism.