This review provides a comprehensive and updated information on chalcones, presenting their sources, methods of identification and properties putting emphasis on applications in agricultural industry. Vast exploitation of synthetic pesticides led to the weed and pest resistance issue, causing economic loss but more importantly health risk due to pesticide overuse. Because one of the aim of the European Green Deal 2030 is the Farm to Fork strategy which targets on reducing by 50% the use of chemical pesticides by 2030, and push towards natural pesticides which are more environmentally friendly and restore natural resources, chalcones and their derivatives seem to fit perfectly. They have herbicidal, fungicidal, bactericidal and antiviral properties. Moreover, chalcones are naturally occurring substances, known for their favorable health effect for years, working on many areas. This review is complementary to the previous ones describing chalcones use in agriculture, updates them but additionally shows methods of detection.

In this study the effects of three different main preparatory tillage operations [ploughing at 0.4 m (P40) and 0.20 m (P20) depth and minimum tillage at 0.20 m depth (MT) each of them carried out at two different soil water contents (WC) [low, 58% (LH) and high, 80% (HH) of field capacity] were investigated. The results obtained in this research show high values of soil strength in term of Penetration resistance (CI) and shear strength (SS) particularly in deeper soil layers at lower water content. Fossil-fuel energy requirements both for P40 LH and P20 LH were 25 and 35% higher with respect to the HH treatments and tractor slip were very high (P40 LH = 32.4%) with respect to the P40 HH treatment (16%). Therefore soil water content had significantly influenced tractor performance during soil ploughing, particularly at 0.40 m depth while MT was not influenced at all. A significant correlation between grain yield and soil penetration resistance was found highlighting how soil strength may be good indicator of its productivity. Obtained results during these field tests allowed considering MT and P20 treatments more suitable for this type of soil in climate change scenarios.

The coffee industry loses millions of dollars annually worldwide due to the Coffee Berry Borer (CBB); these losses imply a decrease in quality and production. Traps are used to monitor their flight and for pest control. The main objective was to determine the flight pattern and trap capture percentages of the CBB population over time using column traps (CTs) in two independent field experiments. CTs were composed of four traps installed at four different heights 0.5, 1.5, 2.5, and 3.5m above ground. Our results demonstrated a significant difference in CBB capture by traps placed at different heights above the ground. The CT capture maintained a pattern throughout this study's lag; the lower the height, the greater the percentage of CBBs captured. In Experiments A and B, the traps placed at 0.5m caught 67% and 85% of the CBBs captured, respectively. Furthermore, the trap set at 1.5m above the ground in the multi-level CT showed a higher capture percentage than the individually placed trap (also at 1.5m). The pattern of the capture and proportion of the CBB in the CTs were maintained throughout the study despite the season, changes in temperature, and relative air humidity. We suggested that CTs could be explored as a useful tool for capturing the CBB, considering its monitoring and management.

Many studies have focused on the impacts of rainfall duration and intensity while overlooking the role of rainfall patterns on intensive tillage erosion in hilly agricultural landscapes. The objective of this study was to determine the combined effects of rainfall patterns and intensive tillage erosion on surface runoff and soil loss on sloping farmland in the purple-soil area of China. Five simulated rainfall patterns (constant, rising, falling, rising-falling, and falling-rising) with the same total precipitation were designed, and the intensive tillage erosion treatment (IT) and no-tillage treatment (NT) were subjected to simulated rainfall using rectangular steel tanks (2 m × 5 m) with a slope of 15°. To analyse the differences in the hydrodynamic characteristics induced by tillage erosion, we calculated the flow velocity (V), Reynolds number (Re), Froude number (Fr), and Darcy-Weisbach resistance coefficient (f). The results indicate that significant differences in surface runoff and soil loss were found among different rainfall patterns and stages (P < 0.05). The falling pattern and falling-rising pattern had faster runoff-initiating times and larger sediment yields than those of the other rainfall patterns. f varied from 0.30 to 9.05 for the IT and 0.48 to 11.57 for the NT and exhibited an approximately inverse trend to V and Fr over the course of the rainfall events. Compared with the NT, the mean sediment yield rates from the IT increased the dynamic range of 8.34%–16.21% among different rainfall patterns. The net contributions of the IT ranged from 2.77% to 46.39% on surface runoff and 10.14%–78.95% on soil loss on sloping farmland. Surface runoff and soil loss were positively correlated with rainfall intensity, V, and Fr but negatively correlated with f irrespective of tillage intensive (P < 0.05). For varying-intensity rainfall patterns, soil and water loss fluctuated during rainfall events, suggesting that the changes in rainfall intensity and tillage intensity would result in drastic variations in soil hydrological characteristics and sediment transport mechanisms. The time sequences of rainfall intensity in each rainfall pattern significantly affected surface runoff, soil erosion, and their contribution rates to total soil and water loss. Moreover, tillage erosion effects on soil and water loss were closely related to rainfall patterns in hilly agricultural landscapes. Our study not only sheds light on the mechanism of tillage erosion and rainfall erosion but also provides useful insights for developing tillage-water erosion prediction models to evaluate soil and water loss on cultivated hillslopes.

We study a two-echelon supply chain made up of a supplier and a manufacturer, both of which can reduce their component/product carbon emissions. With the vertical technology spillovers, we explore the optimal decisions of centralized and decentralized supply chains with price dependent demand and propose coordination strategy for the decentralized supply chain. Considering the cost contraction effectiveness of the technology spillovers, the centralized and decentralized game theoretic models of a two-echelon supply chain are developed to investigate optimal decisions of pricing and carbon emissions reduction. Through a systematic comparison and numerical analysis, we show that the profits of both players and the entire supply chain improve with the effect of technology spillovers increasing. Carbon emissions reduction will be taken by various protective measures so that the supplier and the manufacturer who do not innovate can hardly share the results of innovating via the “free-riding” methods when the technology spillover is relatively small. We also propose a revenue-cost sharing contract through bargaining to enhance the performance of the decentralized supply chain.

This study aimed to evaluate the effects of Blazepod technology when incorporated with various training regimens on the essential elements of physical fitness in volleyball, such as agility, speed, visual response time, and vertical leap. Thirty-six participants (age :17.33±0.48 y, height: 183.78±6.34 cm, weight: 77.14±5.16 kg) were in-volved in this study. In randomized design, three equal groups with two experimental groups and one control group were involved in the study over a period of six weeks: (GE1) used Blazepod technology to workout at a low level; (GE2) used Blazepod technology to workout at a higher intensity; (CG) did not employ Blazepod technology, but it adhered to the same fundamental training curriculum. We conducted agility, speed, reaction time, and vertical jump tests before, midway and after the study to determine optimal training volume, intensity, and frequency. A significant main effect of time (P0.01), and time×group interaction (P>0.001) were found for all tests. Post hoc test showed that the two experimental groups gadget significantly improved in all performance variables (P

Subsoil tillage loosens compacted soil for better plant growth, but promotes water loss, which is a concern in areas commonly irrigated. Therefore, our objective was to determine the physiological responses of high yield spring corn (Zea mays L.) to Subsoil tillage depth when grown in the western plain irrigation area of Inner Mongolia that leads to the best water use efficiency. The experiment during 2014 and 2015 used Zhengdan958 and Xianyu335 with three differing subsoil tillage depths (30, 40, or 50 cm) as trial factor and shallow rotary as a control. Subsoil tillage increased shoot dry matter accumulation, leading to a greater shoot/root ratio. Subsoil tillage helped retain greater leaf area index in each growth stage, increase the leaf area duration, net assimilation rate, and relative growth rate, with greater effects as tillage was deeper, effectively delaying the aging of the blade. Grain yields were increased by 0.7%–8.9% on average in subsoil tillage treatments compared to conventional soil treatment shallow rotary, Water use efficiency were increased by 1.93%–18.49% on average in subsoil tillage treatment compared to shallow rotary, resulting in net income increases by 2.24% to 6.97% compared to shallow rotary. Among the three different subsoil tillage depth treatment, the grain yield, water use efficiency, and net income is the best under the treatment of subsoil tillage depth of 50 cm.

Conservation tillage and deep side-fertilization both hold the potential to reduce nitrogen leaching and improve grain yield and nitrogen use efficiency in fragrant rice cultivation practices. However, the combined impact of different tillage practices with deep side-fertilization on nitrogen leaching remains uncertain. Therefore, this study conducted on-site experiments for four rice growing seasons in both early and late seasons in 2018 and 2019, using the fragrant rice varieties "Meixiangzhan 2"(MX) and "Xiangyaxiangzhan"(XY). The four experimental treatments included:conventional tillage with regular fertilization (T1), conventional tillage with simultaneous deep fertilization (T2), reduced tillage with simultaneous deep fertilization (T3) , and no-tillage with simultaneous deep fertilization (T4). Our results indicate that the T4 treatment exhibited higher nitrogen leaching rates and potential nitrogen losses throughout the entire rice growth cycle, with a 4.51% increase in total nitrogen leaching and a 1.86% increase in potential nitrogen leaching compared to T1. In contrast, the T2 treatment demonstrated the lowest nitrogen leaching rate, resulting in a 6.01% reduction in total nitrogen leaching and a 9.57% decrease in potential nitrogen leaching compared to T1, demonstrating the most optimal performance. For MX, the T1 treatment resulted in lower daily grain outputs compared to the other treatments, with disparities ranging from 5.35% to 9.94%. Similarly, for the XY, the T1 treatment yielded significantly lower daily grain outputs compared to the other treatments, with discrepancies ranging from 6.26% to 10.81% during the late season of 2019. Overall, this study shows that conventional tillage with deep fertilization effectively reduces nitrogen leaching and boosts fragrant rice yields. Minimizing nitrogen leaching enhances nitrogen utilization efficiency. These insights highlight the significance of strategic fertilization and cultivation for environmental conservation and agricultural sustainability.

Studies on N balance due to N inputs and outputs and soil N retention to measure cropping system performance and environmental sustainability are limited due to the complexity of measurements of some parameters. We measured N balance based on N inputs and outputs and soil N retention under dryland agroecosystem affected by cropping system and N fertilization from 2007 to 2011 in the northern Great Plains, USA. Cropping systems were conventional tillage barley (Hordeum vulgaris L.)-fallow (CTB-F), no-tillage barley-fallow (NTB-F), no-tillage barley-pea (Pisum sativum L.) (NTB-P), and no-tillage continuous barley (NTCB). Nitrogen rates to barley were 0, 40, 80, and 120 kg N ha-1. Total N input due to N fertilization, pea N fixation, soil N mineralization, atmospheric N deposition, nonsymbiotic N fixation, and crop seed N and total N output due to grain N removal, denitrification, volatilization, N leaching, gaseous N (NOx) emissions, surface runoff, and plant senescence were 28 to 37% greater with NTB-P and NTCB than CTB-F and NTB-F. Total N input and output also increased with increased N rate. Nitrogen sequestration rate at 0 to 10 cm averaged 22 kg N ha-1 yr-1 for all treatments. Nitrogen deficit ranged from 5 to 16 kg N ha-1 yr-1, with greater deficits for CTB-F and NTB-P and higher N rates. Because of increased grain N removal and reduced N loss to the environment and N fertilizer requirement, NTB-P with 40 kg N ha-1 can enhance agronomic performance and environmental sustainability while reducing N inputs compared to other management practices.

Potato is one of the main crops grown worldwide under different climatic conditions. Potato is conventionally produced under intensive tillage practices under the same or different soil types. Research has shown some contrasting effects of the tillage practices on the soil properties, crop growth, yield, and quality. Under the reducing available freshwater for food production, soil management practices are more targeting conservation and system sustainability. It is therefore critical to revisit literature on the tillage practices and their impact on the soil, crop, and crop yield. This review presents research results of studies conducted exclusively on potatoes comparing different types of tillage practices and is a valuable source of information for potato growers and scientists as it is not only focused on the impact of tillage practices on soil properties but also on potato tuber yield and grade, tuber specific gravity, and the impact of tillage practices on diseases in potatoes.

Atmospheric turbulence characteristics are essential in determining the quality of astronomical images and implementing adaptive optics systems. In this study, the vertical distributions of optical turbulence at the Peak Terskol observatory (43.27472 ° N 42.50083 ° E, 3127 m a.s.l.) using the Era-5 re-analysis and scintillation measurements are investigated. For the closest reanalysis grid node to the observatory, vertical profiles of the structural constant of the air refractive index turbulent fluctuations Cn2 were obtained. The calculated Cn2(z) vertical profiles are compared with the vertical distribution of turbulence intensity obtained from tomographic measurements with Shack-Hartmann sensor. The atmospheric coherence length at the location of Terskol Peak was estimated. Using combination of atmospheric models and scheme paramaterization of turbulence, Cn2(z) profiles at Mt. Kurapdag were obtained. The values of atmospheric coherence length at the Peak Terskol are compared with estimated values of this length at the ten astronomical sites including Ali, Lenghu and Daocheng.

This study investigates the long-term impact of soil tillage systems and crop residue incorporation on agrophysical properties. A long-term field experiment has been conducted since 1999 at the Ex-perimental Station of Vytautas Magnus University Agriculture Academy. According to the latest edition of the International Soil Classification System, the soil in the experimental field was classified as Planosol, with a silty medium loam texture at a depth of 0–20 cm and a silty light loam at a depth of 20–40 cm. This investigation aimed to assess the long-term impact of reduced tillage systems, straw, and green manure combinations on soil physical properties, including soil shear strength, and soil aggregate stability. Studies were carried out on winter wheat crops in 2014, 2017, and 2023. The treatments were arranged using a split-plot design. In a two-factor field experiment, one part of the experimental field had straw removed, while the other part had the entire straw yield chopped and spread at harvest (Factor A). The subplot factor (Factor B) included three different tillage sys-tems: conventional deep ploughing, cover cropping for green manure with no-till, and no-tillage. Soil samples were analysed in the Laboratory of Agrobiology at Vytautas Magnus University Ag-riculture Academy. The findings indicate that long-term application of reduced tillage significantly increases soil shear strength. Shallower tillage depths lead to higher soil shear strength, while the effect of spreading plant residues is relatively lower. Long-term tillage of different intensities, spreading plant residues, and catch crop cultivation for green manure did not significantly affect soil structure. However, soil structural stability was found to be highly dependent on soil tillage. Cover cropping for green manure with no-till and no-tillage positively affected soil aggregate sta-bility in the upper (0–10 cm) and 10–25 cm layers.

Interactions of different factors in differently tilled faba bean agrosystem is still insufficiently studied and evaluated. For these reasons we studied the results of long-term field experiment, which was carried out in the Research Station of Vytautas Magnus University, Agriculture Academy (Lithuania). The aim of this study is comprehensively evaluating the effect of the deep and shallow ploughing, deep cultivation-chiseling, shallow cultivation-disking, and no-tillage systems for faba bean cultivation on the much-interacted factors, relations between them and strength of impact by the integrated evaluation method using complex evaluation index (CEI). Calculations showed that the influence of the no-tillage system was the greatest on the faba bean agrosystem than other system used. Shallow cultivation was more efficient than deep and shallow ploughing and deep cultivation systems. In the deep ploughing system, there were calculated more minimal, i.e. close to 1 as the CEI value, which showed DP ineffectiveness.

At the time of tillage, properties of the soil change, thereby changing the conditions of crop development and ultimately their productivity and quality. The effect of non-inversion tillage or no till on faba bean development is stills not widely investigated. For this reason, investigations of tillage systems from deep and shallow ploughing, chiselling, disking to no tillage were tested in Vytautas Magnus University, Agriculture Academy, Lithuania. The results showed that different tillage methods had less influence on faba bean development than meteorological conditions during the growing seasons. Soil chiselling generally showed better faba bean canopy development rates than other treatments. Faba bean roots developed somewhat better in not tilled plots. Vegetative conditions had a significant influence on faba bean development indicators. The effects of vegetative conditions during all four years of the experimentation were significantly different from each other. This shows that, due to rapid climate change, the conditions of each vegetative season become unique and require precise attention.

A comprehensive investigation was undertaken at Vytautas Magnus University Experimental Station, located at 54°52’50” N latitude and 23°49’41” E longitude on soil (Epieutric Endocalcaric Planosol – PLe-gln-w) since 1999, to understand the impacts of different agrotechnical measures on soil health and crop yield. Two primary factors were assessed. Factor A incorporated practices of straw removal versus straw chopping and spreading, while Factor B evaluated a spectrum of tillage techniques: conventional deep ploughing, shallow ploughing, ploughless tillage, single seedbed discing, and two no-tillage practices, one of which involved cover crops. Findings from this long-term study highlight the significant potential of specific farming systems in enhancing soil organic carbon. It has a positive effect on the release of CO2 emissions from the soil, thus promoting soil resilience and increasing plant productivity. These insights are paramount in devising sustainable agricultural strategies to counter the challenges of climate change on agroecosystems. This research showcases the profound effects of combining residue management and tillage practices, setting a novel standard for sustainable soil management of climatic uncertainties.

An efficient design of conservation tillage trencher (CTT) saves time, natural resources, and conserves soil health by avoiding vigorous soil disturbance of tillage operations. A two-wheel tractor operated CTT has constructed with modified rotary shafts, toolbar frames, depth control bars, bed shapers and chisel ploughs for conservation tillage operation of sugarcane plantation. The performance evaluation of developed CTT was tested for comparing the suitability with small-scale farmer’s practice (SFP) and large farm practice (LFP). Finally, the CTT is applied for preparing sugarcane farmland in different conservation tillage methods of i) bed cum trenching (BT), ii) zero-tillage trenching (ZT) and iii) strip-tillage (ST). The performance of effective field capacities of CTT were 0.14 ha h-1, 0.12 ha h-1 and 0.14 ha h-1 for BT, ZT and ST, respectively. Developed CTT saved time 80% and 26-37% over SFP and LFP, and required 96% and 26-36% less labour than SFP and LFP, respectively. Conservation tillage required 7-10 l ha-1diesel whereas SFP and LFP required 25 l ha-1and 65 l ha-1, which reduced CO2 emission by 60-72% and 85-89% compared to SFP and LFP, respectively. Ultimately, newly developed CTT saved sugarcane land preparation costs by 86% to 90% compared to conventional tillage systems.

Recent state-of-the-art scene text recognition methods have primarily focused on horizontal text in images. However, in several Asian countries, including China, large amounts of text in signs, books, and TV commercials are vertically directed. Because the horizontal and vertical texts exhibit different characteristics, developing an algorithm that can simultaneously recognize both types of text in real environments is necessary. To address this problem, we adopted the direction encoding mask (DEM) and selective attention network (SAN) methods based on supervised learning. DEM contains directional information to compensate in cases that lack text direction; therefore, our network is trained using this information to handle the vertical text. The SAN method is designed to work individually for both types of text. To train the network to recognize both types of text and to evaluate the effectiveness of the designed model, we prepared a new synthetic vertical text dataset and collected an actual vertical text dataset (VTD142) from the Web. Using these datasets, we proved that our proposed model can accurately recognize both vertical and horizontal text and can achieve state-of-the-art results in experiments using benchmark datasets, including the street view test (SVT), IIIT-5k, and ICDAR. Although our model is relatively simple as compared to its predecessors, it maintains the accuracy and is trained in an end-to-end manner.

Tillage has been reported to induce seasonal changes of organic carbon (Сmicro) and nitrogen (Nmicro) in biomass of microorganisms. Soil microorganisms execute such ecosystem functions as: it is an immediate sink of labile biophil elements; it is an agent of a conversion, catalysis and synthesis of humus substances; it transforms soil contaminants into non-hazardous wastes; it participates in soil aggregation and pedogenesis as a whole. However, the seasonal turnover of microorganisms on arable lands in temperate ecosystems has not been investigated on a relevant level. Hence, we aimed to study the dynamics of such soil microbial biomass patterns as: Сmicro, Nmicro, microbial index (MI = (Сmicro/CTOC)·100, %) and CO2-C emission on the background of 9 years of tillage and 22 years of abandoned (Ab) and fallow (F) usage. Our study was conducted on a long-term experimental site on a Mollisol in the northeast China. The maximum Сmicro and Nmicro content was found: at the beginning of the growing season – in 0-10-; in mid-July – in 20-40 cm layers, while the minimum – in August-October. The Сmicro content ranged from 577.79- and 381.79 mg-1 kg-1 under Ab in spring to 229.53- and 272.86 mg-1 kg-1 in autumn under CT (conventional tillage) and F in 0-10- and 10-20 cm layers, respectively. The amplitude of Nmicro content changes was several times lower comparatively to Сmicro. The smallest quartile range (IQR0.25-0.75) of such changes was under: no-till (NT) and Ab in 0-10-, NT and F – in 10-20- and CT - in 20-40 cm layers. The widest Сmicro : Nmicro ratio was found at F and CT – in 0-20- and CT and rotational tillage (Rot) – in 20-40 cm layers. MI dynamics resembled the trends of Сmicro and Nmicro and changed from 0.72  0.168- tо 2.00  0,030 %. The highest part of Сmicro in CTOC was at Ab (1.82  1.85 %) and NT (1.66  1.52 %) – in 0-10-; Ab (1.23  1.27 %) and NT (1.29  1.32 %) – in 10-20- and – Ab (1.19  1.09 %) and F (1.11  1.077 %) – in 20-40 cm layers, correspondingly. The Pearson’s correlation coefficient between Сmicro and CTOC increased from the upper 0-10- to the lower 20-40 cm layer, it was "strong" and "high" between Сmicro and CTOC. Different use of Mollisol affected the amplitude of Сmicro and Nmicro seasonal changes, but it didn’t change their trend. Our results suggest the key role of Ab and NT technologies in Сmicro accumulation in total organic carbon (TOC).

Reduced nutrient mineralization rates under minimum tillage are usually compensated by mineral fertilizer application. These cannot be applied in organic farming systems, however. We hypothesized that organic minimum tillage based on frequent cover cropping and application of dead mulch will improve soil fertility and can compensate for the potential negative effects of minimum tillage. Two long-term field experiments were set up in 2010 and 2011 comparing plough versus minimum tillage including application of transferred mulch. As second factor, the application of compost versus mineral potassium and phosphorus was compared. In 2019, soils were analyzed for soil pH, organic carbon, macro-, micronutrients, microbial biomass, microbial activity and total nematode abundance. In addition, performance of pea in the same soils was determined under greenhouse conditions. Across both experiments, macronutrients (+52%), micronutrients (+11%), microbial biomass (+51%), microbial activity (+86%), and bacterivorous nematodes (+112%) increased in minimum tillage compared with the plough-based system. In the greenhouse, pea biomass was 45% higher in the soil that had been subjected to minimum tillage compared to the plough. In conclusion, soil fertility can be improved in organic minimum tillage systems by intensive cover cropping and application of dead mulch to levels higher than in a plough-based system.

Soil structure is a sensitive and dynamic soil physical property which responds rapidly to different tillage systems, and thus it requires constant monitoring and evaluation. The visual evaluation of soil structure (VESS) and subsoil visual evaluation of soil structure (SubVESS) methods were used to assess the soil structure quality of clayey soils subjected to different tillage systems. The tillage systems were no-tillage (NT), conventional tillage (CT) and virgin land (VG). The study was conducted at Tshivhilwi and Dzingane in Thohoyandou, Vhembe District, Limpopo Province, South Africa. The NT system was practised for 8 and 40+ years at Tshivhilwi and Dzingahe, respectively. The results showed no impact of tillage system on both VESS and SubVESS at Tshivhilwi. The soil structure quality at Tshivhilwi as determined by VESS and SubVESS were found to be poor. However, at Dzingahe, both the VESS and SubVESS responded to the impact of tillage. At Dzingahe VESS showed a fair (Sq = 2.25) soil structural quality in the NT system, poor (Sq = 3.57) in the CT system and moderately poor (Sq = 3.05) in the VG. Similarly, at the same location the SubVESS scores were moderately good in the NT system, moderately poor for CT system and fair in the VG. The differences in the response of the VESS and SubVESS at the two locations were attributed to the differences in the duration at which the NT systems were practised. The VESS and SubVESS results were supported by selected measured soil physicochemical properties such as bulk density and porosity. In conclusion, the findings of this study showed that the VESS and SubVESS were able to effectively differentiate the impact of tillage systems on soil structural quality in clayey soils where NT was practised for a long period (40+ years) while it could not where NT was practised for a few years (8 years).

Atmospheric CO2 concentration, temperature and precipitation escalate and it is critical to investigate the agricultural practices best suited to face such new conditions. An important aspect is soil management, which alters soil organic matter content, nutrients and structure, and thus soil/atmosphere interactions and ultimately production. This in vitro study addresses greenhouse gas (GHG) emissions from two long-term soil management experiments in France. One set of soil columns were managed with either grain legume + cover crops or no grain legumes + bare fallow. The other with either plowed or reduced tillage soils. GHG exchange (CO2, N2O) measurements was conducted under different environmental conditions, before and during growth of barley and eventually with three levels of barley biomass cuts (everything removed, cut halfway, intact). The gas exchange was influenced by time and environmental settings, and to a smaller degree management history, with highly variable emissions of N2O. The environmental treatments induced different patterns of effect depending on the management history of the soils. The gas exchange from soil with grain legume was more responsive to the environmental treatments than the rotation without grain legumes. Depending on the history of tillage, the gas exchange responded likewise differently to the induced environment.

Soil tillage intensity influences the distribution of nutrients, and soil’s physical and me-chanical properties, as well as gas flows. The impact of reduced tillage on these indices in spring barley cultivation is still insufficient and requires more analysis on a global scale. This study was carried out at Vytautas Magnus University, Agriculture Academy (Lithu-ania) in 2022–2023. The aim of the investigation was to determine the effect of the tillage systems on the soil temperature, moisture content, CO2 respiration and concentration in spring barley cultivation limited by the semi-humid subarctic climate. Based on a long-term tillage experiment, five tillage systems were tested: deep and shallow mold-board ploughing, deep cultivation-chiselling, shallow cultivation-chiselling, and no-tillage. Shallow ploughing technology was found to be better at conserving soil moisture and maintaining a higher temperature. Deep cultivation had a lower moisture content and lower soil temperature. Shallow cultivation fields in most cases increased CO2 emissions and CO2 concentration. The results show that in direct sowing fields, most cases had a positive effect on crop density. Direct sowing fields resulted in significantly lower grain yields of spring barley in the years studied.

The capability of in-house transient wave-multibody computational tool of ITU-WAVE are extended to predict the wave power absorption with Wave Energy Converters (WECs) arrays placed in front of a vertical breakwater. The analyses of hydrodynamic exciting and radiation forces are approximated solving boundary integral equation at each time interval. The reflection of incoming waves due to a vertical wall is predicted with method of images. The constructive or destructive performance of WECs arrays with different array configurations is measured with mean interaction factor. The behaviour of the exciting and radiation hydrodynamic forces of each WEC due to a vertical wall effect shows considerable differences than those of WECs arrays without a vertical wall influence. When the wave power absorption with WECs arrays with and without a vertical wall effect are compared, it is shown with numerical experiences that WECs placed in front of a vertical wall have much greater effects on wave power absorption. This can be attribute to the hydrodynamic interaction, standing waves, and nearly trapped waves in the gap between a vertical wall and WECs arrays. The analytical and other numerical results are used to for the validation of the numerical results of the present ITU-WAVE computational tool for exciting and radiation forces, and mean interaction factor of WECs arrays which show satisfactory agreements.

(1) Background: Hemispherotomy is the generally accepted treatment for hemispheric drug resistant epilepsy (DRE). Lateral or vertical approaches are performed according to the surgeon's preference. Multiples technical variations have been proposed since Delalande first described his vertical technique. We propose a sub-insular variation of the vertical parasagittal hemispherotomy (VPH) and describe our case series of patients operated on with this procedure. (2) Methods: a continuous series of patients operated on by the senior author (CR) with the modified sub-insular VPH was retrospectively analyzed. We report the demographic pre-operative characteristics, epilepsy and functional outcome as well as the surgical complications.(3) Results: Twenty-five patients were operated on between August 2008 and August 2023, twenty-three of them have at least a 3-month follow-up. On this last group 86,3% of patients were seizure-free. Only two patients developed post-operative hydrocephalus (8.7%), all patients with autonomous preoperative walk and 86,3% of the total series were able to walk without assistance (86.3%) and perform adapted social activities at last follow-up.(4) Conclusion: The modified vertical parasagittal sub-insular hemispherotomy is a successful surgical technique for hemispheric DRE with seizure freedom rates similar to the biggest series reported in the literature. Compared to other series, patients operated with our modified technique had a lower rate of postoperative hydrocephalus and excellent long-term motor and cognitive outcome.

Rice wheat cropping system prevailed in more than fifty percent areas of rice belt of central and upper Punjab. In this area yield of wheat is curtailed every year due to late harvesting of rice crop. In addition to this, lack of machinery for direct sowing of wheat into combine harvested rice is a major limitation for timely wheat sowing due to presence of heavy straw load dropped by the combine harvester. A field experiment was planned and executed during two consecutive years 2017-18 and 2018-19 at Agronomic Research Station Farooqabad to evaluate the various stubble management techniques for the sowing of wheat in a rice-wheat cropping system. The Experiment consist of four treatments Happy seeder (Zero tillage), conventional sowing without burning of rice stubble, Rotavator two times, and Conventional sowing with the burning of rice stubble. The trail was arranged as a Randomized Complete Block Design with four replications having a net plot size of 8 m x 20 m. The Treatments have significant effects on Plant height, Number of productive tillers, 1000- grain weight, and grain yield. Maximum plant height (94.74 and 94.25 cm), numbers of productive tillers/m2 (324.00 and 322.25), 1000-grain weight (36.35 and 36.20 g), grain yield (3780 and 3613 kg/ha), and benefit-cost ratio (2.54 and 2.43) were recorded from the treatment happy seeder (Zero tillage) during both years respectively. It is concluded that the sowing of wheat with a happy seeder (Zero tillage) is an appropriate technique in the rice-wheat cropping system by protecting the environment and soil health from the burning of rice stubbles.

Fruits and vegetable diagnosis and inspection is a crucial part of quality control and health safety. From harvesting to retailing, stakeholders encounter tons of food losses due to the lack of monitoring of the fruit condition in retail. The problem gets worse because it is being handled by many people, including retailers and customers. We propose a transparent fiberglass-made vertical fruit showcase, which provides 80 percent more visibility, takes lesser shop space, and prevents human contact. It is convenient for the retailer and customer to use. Moreover, the controlled fruit environment is easy to integrate with IoT, which will help to generate consensus data for fruit management decisions in machine learning.

Soil-borne oomycetes include devastating plant pathogens that cause substantial losses in the agricultural sector. To better manage this important group of pathogens, it is critical to understand how they respond to common agricultural practices, such as tillage and crop rotation. Here, a long-term field experiment was established using a split-plot design with tillage as the main plot factor (conventional tillage [CT] vs. no till [NT], 2 levels) and rotation as the subplot factor (monocultures of soybean, corn, or wheat, and corn-soybean-wheat rotation, 4 levels). Post-harvest soil oomycete communities were characterized over three consecutive years (2016-2018) by metabarcoding the Internal Transcribed Spacer 1 (ITS1) region. The community contained 292 Amplicon Sequence Variants (ASVs) and was dominated by Globisporangium spp. (85.1% in abundance, 203 ASV) and Pythium spp. (10.4%, 51 ASV). NT decreased diversity and community compositional structure heterogeneity, while crop rotation only affected the community structure under CT. The interaction effects of tillage and rotation on most oomycetes species accentuated the complexity of managing these pathogens. Soil and crop health represented by soybean seedling vitality was lowest in soils under CT cultivating soybean or corn, while grain yield of the three crops responded differently to tillage and crop rotation regimes.

Farmers’ conventional tillage (CT) and residue removal practices in rice-maize systems in South Asia’s Eastern Gangetic Plain (EGP) are input-intensive, costly and soil degradative. We conducted a rice-maize-mungbean (R-M-MB) system experiment with six tillage and three residue management treatments in Bangladesh representing the EGP. Maize yields were significantly (p≤0.05) higher under permanent (PB) or fresh (FB) beds and strip tillage (ST) than CT but no differences in mungbean yields. Rice yields under PB, FB and CT were similar, but significantly higher than under zero or minimum tillage and ST. Yields of all crops increased significantly (p≤0.05) with residue retention compared to no retention. Total system productivity was highest under PB followed by FB and ST. Compared with CT, gross margins in PB, FB and ST increased by 18, 13 and 11%, and soil organic matter (SOM) and total N contents across tillage treatments increased by 11-16% and 12-24%, respectively. After three years, SOM and total N and available P and S contents increased significantly (p≤0.05) by residue retention. Results demonstrate the potential of PB, FB and ST with residue retention, for improving the productivity, profitability and soil health under R-M-MB systems in Bangladesh and similar soils in the EGP.

No-till and cereal-legume intercropping have been recognized as favorable cropping practices to increase crop yields while maintaining soil quality in arid and semiarid environment, but the bio-logical mechanisms are poorly understood. The present study was to determine the response of soil properties, enzyme activities, and microbial community diversity and composition in mono- and inter-cropping under conventional and no-tillage conditions. We initiated a field experiment in Wuwei, a typical arid area of China, in 2014. Soil was sampled in August 2022 and, yields, soil properties, enzyme activities, and the microbial community diversity and composition were de-termined in the maize and pea strips in inter- and mono-cropping systems. Results revealed that the maize and pea strips in the no-till intercropping significantly increased yields, total and or-ganic carbon stocks, decreased NO3--N, and obtained the highest total and organic P in the soil. The α- and β-diversity of archaea and eukaryotes were significantly affected by planting patterns, while α- and β-diversity of the bacterial community were significantly affected by tillage practices. Both no-tillage and intercropped maize significantly increased the abundance of archaea phylum Thaumarchaeota and bacterial phylum Nitrospirae, benefiting nitrogen fixation of intercropped pea from the atmosphere under the no-tillage cereal/legume intercropping. No-till intercropping was conducive to the accumulation of organic carbon, while decreasing the abundance of Prote-obacteria, Acidobacteria, and Verrucomicrobia. Limited soil enzyme activities (ACP, ALP, DP, NAG, BG, AG, CB) led to decreases in organic carbon turnover and utilization. Intercropping al-tered soil microbial community diversity and composition due to changes in soil properties and enzyme activities. These findings suggest that no-tilled cereal-legume intercropping is a sustaina-ble cropping practice for improving soil properties and enhancing microbial (archaea, bacterial, Eukaryota) diversity, but the long-term persistence is not conducive to rapid turnover of soil nu-trients due to limited enzyme activities.

Intense rainfall events frequently occur in Brazil, often leading to rapid flooding. Despite their recurrence, there is a notable lack of sub-daily studies in the country. This research aims to assess patterns related to the structure and microphysics of clouds driving intense rainfall in Brazil, resulting in high accumulations within 1 hour. Employing a 40 mm/h threshold and validation criteria, 83 events were selected for study, observed by both single and dual-polarization radars. Contoured Frequency by Altitude Diagrams (CFADs) of reflectivity, Vertical Integrated Liquid (VIL), and Vertical Integrated Ice (VII) are employed to scrutinize the vertical cloud characteristics in each region. To address limitations arising from the absence of polarimetric coverage in some events, three case studies focusing on polarimetric variables are included. A fourth case study enhances the overall understanding of these events, emphasizing the underexplored nature of short-term intense rainfall studies in Brazil. Results reveal that the generating system significantly influences the rainfall pattern, especially in the Southern, Southeastern, and Central-Western regions. Regional CFADs unveil primary convective columns with 40-50 dBZ reflectivity, extending to approximately 6 km. The microphysical analysis highlights the rapid structural intensification, challenging the event predictability and the issuance of timely specific warnings.

This study presents a dynamic modeling approach to investigate the impact of saturation dynamics on HIV/AIDS transmission in the presence of vertical transmission and treatment strategies. The proposed model incorporates disease-free and endemic equilibria, with a focus on analyzing the basic reproduction number and conducting stability analysis. Results indicate that the disease-free equilibrium is locally asymptotically stable under certain conditions. The findings suggest that a combination of treatment interventions and awareness campaigns, along with other control measures, may play a crucial role in curbing the spread of the HIV/AIDS virus. This research contributes to understanding the complex dynamics of HIV/AIDS epidemics and highlights the importance of considering saturation effects in epidemic modeling.

Amid the deepening imbalance in the supply and demand of allogeneic organs, xenotransplanta-tion can be a practical alternative because it makes an unlimited supply of organs possible. How-ever, to perform xenotransplantation on patients, the source animals to be used must be free from infectious agents. This requires breeding of animals using assisted reproductive techniques, such as somatic cell nuclear transfer, embryo transfer, and cesarean-section, without colostrum de-rived in designated pathogen-free (DPF) facilities. Most infectious agents can be removed from animals produced by these methods, but several viruses known to pass through the placenta are not easy to remove, even with these methods. Therefore, in this review, we look at the characteris-tics of several viruses known to cross the placenta and determine how they can be detected. This review is intended to help maintain DPF facilities by preventing animals infected with the virus from entering DPF facilities and to help select pigs suitable for xenotransplantation.

Ensuring the security of vertical applications in fifth-generation (5G) mobile communication systems and previous generations is crucial. These systems must prioritize maintaining the confidentiality, integrity, and availability of services and data. Examples of vertical applications include smart cities, smart transportation, public services, Industry 4.0, smart grids, smart health, and smart agriculture. Each vertical application has specific security requirements and faces unique threats within the mobile network environment. Thus, it is essential to implement comprehensive and robust security measures. This approach helps minimize the attack surface and effectively manage risks. This survey thoroughly examines mobile networks and their security challenges in vertical applications, shedding light on associated threats and potential solutions. Our study considers the interplay between security considerations in 5G, legacy networks, and vertical applications. We emphasize the challenges, opportunities, and promising directions for future research in this field and the importance of securing vertical applications in the evolving landscape of mobile technology.

The impact of long-term soil and crop management practices on soil biological and chemical properties in oilseed brassica-based production systems were deliberated for holistic soil health improvement in the present study. Different tillage, crop residue re-cycling and cropping systems were studied for 5-years in 0-15 and 15-30 cm soil profiles. No-till permanent beds with crop residue (PB+R) noticeably improved soil organic carbon (SOC), microbial biomass carbon (MBC), enzymes [dehydrogenase (DHA) and alkaline phosphatase (AlP)], nitrogen fractions (available, nitrate and total), and available phosphorus and potassium content in both the soil layers compared to conventional tillage without crop residues. Though, the plow soil layer (0-15 cm) showed higher concentration of soil carbon, enzymes, N fractions and available P than in the sub soil (15-30 cm). The dynamic soil biological and chemical properties were also varied with the crop stage, and recorded higher MBC at 30 days, SOC and enzymatic activities at 60 days, and N fractions and available P and K at harvest of mustard crop. Green gram-mustard rotation showed higher values of biological and chemical parameters. Thus, the legume-based mustard crop rotation following no-till permanent beds and residue re-cycling found holistic in improving soil health, and nutrient cycling.

Vertical-channel organic dual-gate/base transistors would be highly interesting since vertical organic transistors are the fastest organic transistors demonstrated today. However, incorporating a dual gate/base structure into an ultra-short channel vertical architecture represents a substantial challenge. Here, we successfully realize a new device concept of vertical organic permeable dual-base transistors (OPDBTs), where either of both base electrodes can be used to change the on-currents and tune the threshold voltages. The optimized devices yield a high on-current density of 1.54 A cm^-2 and a large current gain of 9.2×10⁵, corresponding to a high transmission value of 99.998%. The detailed operation mechanisms are investigated by calibrated TCAD simulations with the Poole-Frenkel mobility model, Gaussian density of states and tunneling model. Finally, high-performance logic circuits, e.g. inverter, NAND/AND computation functions are demonstrated with one single OPDBT operating at supply voltages of < 2.0 V. We believe that OPDBTs offer a compact and technologically simple hardware platform with excellent application potential for vertical-channel organic transistors in complex logic circuits.

Rotary tillage is a main management tillage practices and widely applied in the North China Plain. However, the long term rotary tillage (depth of 20 cm) results in soil compaction and plow pan formation, which reduces water use efficiency and nutrient uptake, and then impedes the yield increase. In this study, a 3-year field experiment was conducted to investigate the influence of different depths of tillage on soil bulk density, field capacity, water use, photosynthetic rate, nutrients and maize yields in the North China Plain. Three depths of tillage (D20, depth of 20 cm; D25, depth of 25 cm; D30, depth of 30 cm) were assessed. D25 and D30 significantly reduced soil bulk density and improved field capacity in 10-20 and 20-30 cm soil layer, compared to D20. Soil water consumption for D25 was significantly higher 10.12% and 6.61% than that for D20 and D30, respectively. Photosynthetic rate for D25 significantly improved than that for D20 and D30. Total nitrogen in 0-20cm soil layer decreased with the depths of tillage. The maize yields for D25 significantly increased by 20.92% and 21.56% compared to that for D20 and D30, respectively. Structural equation models showed that the total effects of tillage, total nitrogen, photosynthesis and soil water consumption on yields were 0.019, -0.628, 0.121, and 0.895 (path coefficients λ), respectively. The results demonstrated that D25 could improve maize yields, water use efficiency, photosynthetic rate by improving soil water consumption. Depth of 25 cm is optimal tillage practice for the maize production in the North China Plain.

This paper presents the experimental and numerical studies of the vertical stress distribution beneath the centerline of circular footings resting on the sand. Vertical stress values due to circular load in medium-dense sand were measured using soil stress transducers. Reduced-scale laboratory model tests were carried out in a square-shaped test box and vertical stresses were measured at the centerline of the circular footing at different depths of the sand. In order to determine the effect of footing width on vertical stress distribution, laboratory experiments were performed on circular footings of different diameters. In addition, a series of finite element analyses was carried out on the test model to validate the findings of the experimental study. In the numerical analysis, the sand was modeled as a non-linear elastoplastic material. The analyses were performed using the finite element method with two-dimensional axisymmetric and three-dimensional conditions. The results obtained from laboratory model tests and numerical analysis were compared with the vertical stress values obtained from the theoretical solution in the literature. Vertical stress distribution in horizontal planes at any depth from the footing base shows the same characteristic form in all methods. However, some differences were observed between experimental, numerical, and theoretical results and discussed.

The global demands for various grains including durum wheat (Triticum durum Desf.) are expected to increase substantially in the coming years due to ever-growing human population’s needs for food, feed and fuel. Thus, providing consistent or increased durum grain to the world market is one of the priorities for policy-makers, researchers, and farmers. What are the major achievements in agronomic advancement for durum wheat cultivation in recent decades? How might the current cropping systems be improved to increase crop yield and quality and improve resource use efficiencies while minimizing input costs and decreasing negative impact on the environment? Canada is one of the major durum wheat producers in the world, as Canada contributes about 50% to global trade of durum grain. Canada’s research achievements in durum wheat might serve as a guide for advancing the cultivation of the crop in other regions/countries on the planet. This review summarizes the major Canadian research findings in the aspects of durum wheat agronomics during the period 2001 to 2017 years. It highlights the main advancements in seeding and tillage, crop rotation and diversification, and use of pulse-induced microbiomes to improve soil health and feedback mechanism. The genetic gain and breeding for resistance against abiotic and biotic stresses are discussed. Finally, we identified main constraints and suggested some near-term research priorities. The research findings highlighted in this review will be of use for other areas on the planet to increase durum wheat productivity, improve soil fertility and health, and enhance long-term sustainability.

The publication presents an innovative tower cultivation device designed to significantly increase vertical farming efficiency. The device divides the cultivation system into separate chambers. One division corresponds to the different growth phases of the plants, while another reflects the daily variation in conditions. Each chamber presents slightly different conditions and cultivation patterns from the others. For the early stages, crops are grown horizontally in trays once they mature, transplanted into mobile cultivation towers. The closed circulation of ventilation and irrigation reduces water consumption by up to 95%. A unique separate day-night division optimises light, temperature and humidity conditions, mimicking natural growth patterns. This approach not only saves water and energy but also optimises cultivation in a three-dimensional space. The presented solution focuses on the often overlooked aspects of cultivating in vertical farms and makes this method of growing much more cost-effective and feasible to implement on a large scale.

This paper proposes a novel concept within Quantum Natural Language Processing (QNLP) to encode the interpersonal metafunction of Systemic Functional Linguistics (SFL), particularly tenor, into quantum circuits by treating Japanese honorifics seriously. Because of English language bias in the literature, the incorporation of nuanced aspects of interpersonal communication evident in languages, such as the aforesaid Japanese, remains under-developed and overlooked. Utilizing lambeq, monoidal categories, and string diagrams, this study extends lambeq’s quantum computing framework to capture not only grammar but also social context—specifically the roles and relationships that define interpersonal interactions in quantum circuits. This approach represents a significant step toward that end simply by defining the honorific type h in lambeq. This innovative strategy exposes the capability of quantum circuits to model the complex structures of language, moving beyond grammar and even semantics—the horizontal, textual dimension of language—to embrace the vertical, hierarchical dimension of human communication and social interaction. Through this lens, the paper underscores the potential of QNLP to transcend traditional linguistic analysis, advocating for a broader and more nuanced understanding of language that includes not only what is said but also the social persona of the interlocutors. An algorithm for parsing Japanese grammar into pregroup diagrams containing the h type is introduced along with a codebase for other researchers to use and to which to contribute. Lastly, a toy experiment is performed to demonstrate that the circuits generated from these pregroup diagrams are suitable for Quantum Machine Learning (QML) applications.

The most important issue in integrated next generation wireless systems (NGWS) by fourth generation networks which consists of various wireless architectures extending from cellular networks to satellite networks is to allow everyone around the world to connect seamlessly to applications anywhere at any time through the best network. Heterogeneous networks have created many challenges such as mobility management, handoff, resource management. For always best connectivity the selection of parameters plays an important role in the decision of vertical handoff, some of parameters are depend upon MT and some are depend upon the network conditions . In this paper we designed Intelligent Vertical Handoff based on Fuzzy Logic Decision model ( IVH-FL), IVH-FL model which has five parameters for vertical handoff decision : Received Signal Strength (RSS), Available bandwidth (B), Users Preference (UP), Mobile Speed (SM) and Power Consumption (PC), with the help of Fuzzy Logic tool box and concept of fuzzy linguistic variables. The results confirmed improvement performance , and reduced the number of unnecessary handover .

As the demand for liquefied petroleum gas (LPG) continues to increase worldwide, more LPG facilities are being constructed. However, the design and manufacture of pressure vessels used to store dangerous liquids or pressurised fluids, such as LPG, has been a major cause of hazards, including explosions and leakage. In this study, we aim to address this issue by designing and analysing a vertical pressure vessel with a capacity of 10 m3 of pressurised LPG in accordance with the American Society of Mechanical Engineers (ASME) code. Safety is the primary concern in designing pressure vessels due to the potential risks posed by accidents. Therefore, the main objective of this project is to design a pressure vessel that is safe from failure. The vessel is cylindrical with two elliptical heads, two nozzles, a manway and four leg supports, and we used Autodesk Inventor Professional 2023 for geometric modelling and Inventor Nastran for FEA analysis. To investigate the displacements, deflections and Von-Mises stresses in the pressure vessel, we used the finite element method, and Autodesk Inventor Nastran was employed for the analysis. Our results showed that changes to the structure of the pressure vessel were needed to reduce stress in the structure. Specifically, the displacement showed an inverse relationship with the tank section shell thickness. Moreover, we observed that the factor of safety increased linearly with shell thickness. We carefully considered permissible pressures and determined the required wall thickness to ensure acceptable maximum stresses. Our results indicate that the design is safe from failure, and the highest stresses are experienced by the manway followed by the shell, while the heads, nozzles and legs support experienced the lowest stresses. We also performed a theoretical calculation for the entire model and checked the results to ensure they were within the acceptable limits. In summary, our study highlights the importance of designing pressure vessels in accordance with ASME codes to ensure safety and prevent hazards caused by improper design and manufacturing. By using the finite element method, we identified potential stress points in the pressure vessel and were able to make modifications to improve its safety.

The application of numerical simulation methods for studying vertical-axis wind turbines offers significant advantages over conventional horizontal-axis wind turbines regarding wind energy utilisation, start-up wind speed, and environmental impact. This paper aims to investigate and establish the aerodynamic design performance of asymmetrical (NACA 4412) airfoils used in the application of vertical-axis wind turbines. The computational fluid dynamics (CFD) simulation uses Ansys software based on the Reynolds Averaged Navier-Stokes (RANS) equations. The aerodynamic parameters (pressure and velocity) are evaluated and compared within a range of angles of attack (AoA) 5-12 degrees at a fixed Reynolds number, as is a usual condition for wind turbine application. The lift coefficient (Cl), drag coefficient (Cd), and Cl/Cd ratio are obtained within the range AoA for the asymmetrical airfoils, and the performances have been predicted using the potential flow panel and CFD methods. This study suggests that while Xfoil may not be as precise as computational fluid dynamics (CFD), its predicted lift and drag coefficients generally align with experimental results. These help us to understand the best air-foil selection in a wind turbine application and predict its optimum AoA at which it performs at its best.

It is known that people perceive animacy in objects. However, many studies on animacy and emotional expressions are limited in that the investigated motions were created by experimenters themselves. This makes the objective validity unclear. Moreover, it remains unclear what types of movements can express emotions with animacy due to the limited number of investigations examining both animacy and emotional expressions. Therefore, we investigated the motion elements for both animacy perception and emotional expressions using simple objects that lack features of specific living things, such as eyes, ears, tails, and voices in this study. First, we investigated the motion elements for animacy perception and emotional expressions using a robot simulator that enabled participants to create undulatory motions by tuning parameters for speed, height, and randomness. In total, 64 participants created motions in Normal (neutral), Joy, Sad, Relaxed, and Angry conditions. The results showed that the medians of speed and height in Normal, related only to animacy, were 0.5569[Hz] and 3.050cm at the edges/4.575cm at the center. The differences in Joy were 0.4028[Hz] and 3.348cm/5.022cm, in Sad were −0.1652[Hz] and −0.9982cm/−1.497cm, in Relaxed were −0.1979[Hz] and −0.4902cm/−0.7353cm, and in Angry were 0.5212[Hz] and 4.688cm/7.032cm. Second, we investigated whether the motion elements revealed in the first experiment were sufficient to express emotions with animacy, using a robot simulator that reflected the results of the motion element investigation. In total, 44 online participants observed the simulator. The results showed that participants could understand emotional arousal levels at the same time as animacy, but they did not fully understand emotional valence. Our findings provide design guidelines for robots that exhibit emotional expressions and closely interact with humans.

Main purposes and research question: Wheat is the second largest grain crop by tonnage in the world and the largest in Denmark. Given the observed, adverse impacts on wheat yields of climate change and the importance of wheat in the human diet, the purpose of this study was to use life cycle assessment to compare conventional wheat farming with indoor vertical farming using hydroponics. Methods: Life Cycle Assessment was used to assess the base case systems up to the “farm gate” for 1 tonne of wheat grain. The processes contributing most of the impacts were identified, and scenarios were assessed to determine how much the impacts could be reduced. Results: The conventional system outperformed the base case vertical system in every impact category, due to the electricity consumption in the lighting system. The scenarios included increasing the efficiency of the LED lighting and using 100% wind energy, but the conventional system still outperformed the vertical system by significant margins in all impact categories. This was due to the low photosynthetic conversion efficiency and the high energy density of wheat. Conclusions: Until significant improvements are made to lighting efficiency, the photosynthesis conversion efficiency of wheat, new wheat variants designed for vertical gardens and the sustainability of electricity supply, conventional wheat production will be environmentally preferable and vertical gardens would be advised to focus on food products with low energy densities.

Vertical farming (VF) is a potential solution for the production of high-quality, accessible, and climate-friendly nutrition for growing urban populations. However, to realize VF’s potential as a sustainable food source, innovative technologies are required to ensure that VF can be industrialized on a massive scale and extended beyond leafy greens and fruits into the production of food staples or row crops. A major obstacle to the economic and environmental sustainability of VF is the lighting energy consumed. While technological advances have improved the energy efficiency of VF lighting systems, there has been insufficient research into biostimulation as an approach to reduce energy needs. We conducted a controlled trial to investigate the application of a phycocyanin-rich Spirulina extract (PRSE) as a biostimulant in hydroponically grown, vertically farmed lettuce (Lactuca sativa and Salanova®). PRSE application reduced the time from seeding to harvest by 6 days, increased yield by 12.5%, and improved quality including color, taste, texture, antioxidant flavonoid levels and shelf life. Metagenomic analysis of the microbial community of the nutrient solution indicated that PRSE increased the overall bacterial diversity including raising the abundance of Actinobacteria and Firmicutes and reducing the abundance of potentially pathogenic bacteria. This preliminary study demonstrates that microalgae-derived biostimulants may play an important role in improving the economic and environmental sustainability of VF.

Mercury is a neurotoxin, with certain organic forms of the element being particularly harmful to humans. The Minamata Convention was adopted to reduce the intentional use and emission of mercury. Because mercury is an element, it cannot be decomposed. Mercury-containing products and mercury used for various processes will eventually enter the waste stream, and landfill sites will become a mercury sink. While landfill sites can be a source of mercury pollution, the behavior of mercury in solid waste within a landfill site is still not fully understood. The purpose of this study was to determine the depth profile of mercury, the levels of methyl mercury (MeHg), and the factors controlling methylation in an old landfill site that received waste for over 30 years. Three sampling cores were selected, and boring sampling was conducted to a maximum depth of 18 m, which reached the bottom layer of the landfill. Total mercury (THg) and MeHg were measured in the samples to determine the characteristics of mercury at different depths. Bacterial species were identified by 16S rRNA amplification and sequencing, because the methylation process is promoted by a series of genes. It was found that the THg concentration was 19–975 ng/g, with a geometric mean of 298 ng/g, which was slightly less than the 400 ng/g concentration recorded 30 years previously. In some samples, MeHg accounted for up to 15–20% of THg, which is far greater than the general level in soils and sediments, although the source of MeHg was unclear. The genetic data indicated that hgcA was present mostly in the upper and lower layers of the three cores, merA was almost as much as hgcA, while the level of merB was hundreds of times less than those of the other two genes. A significant correlation was found between THg and MeHg as well as between MeHg and MeHg/THg. In addition a negative correlation was found between THg and merA. The coexistence of the three genes indicated that both methylation and demethylation processes could occur, but the lack of merB was a barrier for demethylation.

With the changing climate, there is an increasing emphasis on drought-resistant varieties including the ability to maintain quality production. As there is also interest in ancient wheat varieties, the aim of this study was to evaluate the ancient Khorasan (Kamut ®) with the modern Kabot spring wheat variety using remote sensing data. Images from unmanned aerial vehicles during four growing seasons were processed. Based on vegetation indices, the growth of these varieties and their response to meteorological conditions were evaluated, as well as the ability to resist drought and higher temperatures with respect to specific soil conditions under conventional (CT), minimum (MTC) and minimization (MTD) tillage. It was found that the Khorasan had the lowest values of the vegetation indices on the CT variant in the dry years 2022 and 2023. On the contrary, in the previous wet years 2020 and 2021, both varieties showed similar results. Regarding to water stress, the CT variant was also the least suitable for ancient Khorasan (average CWSI = 0.38). On the contrary, this variant seems to be suitable for the modern Kabot variety (CWSI = 0.29), while no significant difference between tillage variants was found for this variety. In general, water stress was easily detectable by the observed parameters in the growth phase of stem elongation (R2 up to 0.88).

This study is part of an extended investigation into the quantitative detection of therapeutic molecules with antineoplastic properties, specifically focusing on bleomycin. The objective is to minimize adverse effects while maximizing therapeutic effectiveness. We are presenting the results for bleomycin detection, in terms of cyclic voltammetry and electrochemical impedance spectroscopy. We are continuing an approach we have recently started, of an electrochemical biosensor based on graphene, which is evidenced to be a revolutionary nanomaterial. The vertical graphene biosensor exhibited improved sensitivity, faster response, faster occurrence of the chemical reactions, and higher electrode surface conductivity, than the classical gold IDE sensor. The construction of the electrochemical sensor involved growing vertically aligned graphene nanosheets on the conductive surface of interdigitated electrodes. The results for bleomycin detection emphasized that a simpler surface modification method proved to be more efficient.

The holy town of Joshimath, gateway to the India-China border and religious places like Badrinath, Hemkunt Sahab, Valley of flowers in the Uttarakhand state of India experienced cracks in many of the residential and commercial buildings in the month of November-December 2022 which created panic and relocation of people. The reason(s) for the subsidence is still not known but using the InSAR technology and data from Sentinel-1, SAR data for the region was processed using HyP3 and MintPy for January-December 2022 to understand when the phenomenon started and how much uplift/subsidence the area has underwent in the last one year, as no such study is available till today. The entire town can be classified into two zones with respect to the annual subsidence values. Severe subsidence has been observed in the North and East regions whereas most of the southern region experienced moderate to low subsidence. Since the town is built on the debris of an old landslide, the subsidence may be attributed to the change in the course of the underground water channels due to heavy and continuous construction happening in the region and also due to drop in the water table. The results shows that the subsidence in the region was ongoing since June (from January till May, almost negligible vertical movement was recorded) which accelerated after September (when an uplift was recorded which lasted till October), while the subsidence peaked in the month of December with recorded subsidence of as much as 10 cm in some areas located around the Joshimath town, where most of the residential and commercial buildings are located.

Water availability is a major constraint for spring wheat production on the western Loess Plateau of China. The impact of tillage practices on water potential, water potential gradient, water transfer resistance, yield, and water use efficiency (WUEg) of spring wheat was monitored on the western Loess Plateau in 2016 and 2017. Six tillage practices were assessed, including conventional tillage with no straw (T), no-till with straw cover (NTS), no-till with no straw (NT), conventional tillage with straw incorporated (TS), conventional tillage with plastic mulch (TP), and no-till with plastic mulch (NTP). No-till with straw cover, TP, and NTP significantly improved soil water potential and root water potential at the seedling stage and leaf water potential at the seedling, tillering, jointing, and flowering stages, compared to T. These treatments also significantly reduced the soil-leaf water potential gradient at the 0-10 cm soil layer at the seedling stage and at the 30-50 cm soil layer at flowering, compared to T. Thus, NTS, TP, and NTP reduced soil-leaf water transfer resistance and enhanced transpiration. Compared to T, the NTS, TP, and NTP treatments significantly increased biomass yield (BY) by 18, 36, and 40%, respectively, and grain yield (GY) by 28, 22, and 24%, respectively, with corresponding increases in WUEg of 24, 26, and 24%, respectively. These results demonstrate that NTS, TP, and NTP improved GY and WUEg of spring wheat by decreasing the soil-leaf water potential gradient and soil-leaf water transfer resistance and enhancing transpiration, and are suitable tillage practices for sustainable intensification of wheat production in semi-arid areas.

Vertical III-V semiconductor nanowires have shown promising absorption of light for solar cell and photodetector applications. The absorption properties can be tuned through the choice of III-V materials and geometry of the nanowires. Here, we review recent progress in the design of the absorption properties of both individual nanowires and nanowire arrays. Future directions for the research field are proposed.

Ho Chi Minh City (HCMC), the most crowded city and economic hub of Viet Nam, has been experiencing land subsidence over the past decades. This effort aims to contribute the spatial distribution of subsidence in HCMC in its horizontal and vertical components using synthetic aperture radar interferometry (InSAR) time series. To this purpose, an advanced Persistent Scatterers and Distributed Scatterers (PSDS) InSAR technique was applied to two European Space Agency (ESA) Sentinel-1 datasets consisting of 96 ascending and 202 descending images, acquired from 2014 to 2020 over the HCMC area. A time series of 33 COSMO-SkyMed ascending images was also used for comparison. The combination of ascending and descending satellite passes is used to decompose the light of sight velocities into horizontal east-west and vertical components. Taking into account the presence of east-west horizontal motion, our findings indicate that the accuracy of the decomposed vertical velocity can be improved by up to 3 mm/year for Sentinel-1 data. The obtained results revealed that subsidence is most pronounced in the areas along the Sai Gon River, in the northwest-southeast axis, and in the southwest of the city, with a maximum value of 80 mm/yr, which is in accordance with the findings of the literature. The amplitude of east-west horizontal velocities is relatively small and large-scale eastward movement can be observed in the west of the city at a rate of 3-5 mm/yr. This confirmed that the displacement in Ho Chi Minh City area is mainly vertical downward. Together, these results reinforced the remarkable suitability of ESA's SAR Sentinel-1 for subsidence applications, even for non-European countries such as Vietnam and Southeast Asia.

Lichens are traditionally divided into short “crustose”, intermediate “foliose” and tall “fruticose” types, a practice that hides a growth continuum. Substrate, temperature and water are thought to affect vertical growth, but such factors are difficult to measure, because, for example, the water actually available to lichens does not match rainfall patterns or even ground water levels. To reliably assess the effect of those factors, I recorded temperature, moisture, and substrate in and under individual terricolous lichen colonies in 60 fixed quadrats on April, August, October, and December of 2015 (Cerro de la Muerte, Costa Rica, 9°33′N; 83°45′W). The measurements were taken inside the colonies themselves (rather than on the general environment), covering an annual cycle of the relatively simple páramo habitat, where animals and vegetation have less impact than in lower ecosystems. The hypotheses were that lichens would grow taller on softer, warmer, and moister ground; on the Caribbean versant; and on the rainy season. Results matched the hypotheses, with one exception: lichens on soft ground were not taller than those on rock. Caribbean colonies were, on the average, 7 cm taller than those on the drier Pacific versant. Physiologically available water seems to be the main determinant of lichen vertical growth: more water means taller lichens and greater protection from climatic change for both the lichens and their microcommunities.

The main focus of this paper is to propose a comprehensive framework for the cognitive meas-urement and modelling of the built environment. This will involve exploring and measuring neural mechanisms. The aim is to create a foundation for further studies in this field that are consistent and rigorous. Additionally, this framework will facilitate collaboration with cognitive neuroscientists by establishing a shared conceptual basis. The goal of this research is to develop a human-centric approach for urban design that is scientific and measurable, producing a set of urban design guidelines that incorporate cognitive measurement and modelling. By doing so, the broader intention is to design urban spaces that prioritize human needs and well-being, mak-ing them more liveable.

The narrow parking space will result in difficulties in path planning and spot turning caused by sudden changes and discontinuities in path curvature. To address the problem, this paper investigates the performance of three path planning algorithms and proposes a path optimization algorithm. First, the narrow parking space is defined based on single-step parking of the arc-line combination parking algorithm. Second, to compare the arc-line combination algorithm, Hybrid A* algorithm, and particle swarm optimization parking algorithm under different narrow parking spaces, a multi-objective evaluation function is proposed, including three evaluation indicators, namely, the path length, the number of positive and negative conversions of vehicle speed, and the smoothness of the path. Their performance is compared by simulation conducted in MATLAB, the results show that the Hybrid A* algorithm is the better than others for narrow parking spaces. Third, to smooth the planning path, a path optimization algorithm based on the cubic B-spline curve and gradient descent is proposed. Finally, the simulation is conducted between the proposed algorithm and Hybrid A* algorithm, the result shows that the proposal can effectively eliminate the curvature mutation point and constrain the path curvature to meet the requirements of a smooth path.

Vertical graphene nanowalls (VGNWs) have emerged as a highly promising material in recent years due to their exceptional properties, such as a high specific surface area, excellent electrical conductivity, scalability, and compatibility with transition metal compounds. These attributes make VGNWs a compelling candidate for various applications, including energy storage, catalysis, and sensing, fostering great interest in their use in next future commercial graphene-based sensors like optoelectronic and plasmonic devices, energy storage electrodes, and catalytic systems. Among the diverse graphene synthesis methods, plasma-enhanced chemical vapor deposition (PECVD) has proven to be a robust technique for producing large-scale graphene films and creating VGNWs on diverse substrates. However, despite substantial progress in optimizing growth conditions to achieve micrometer-sized graphene nanowalls, the outcomes are often obtained through empirical approaches, and a comprehensive understanding of the underlying physicochemical mechanisms governing nanostructure formation remains elusive. In particular, a deeper exploration of atomic-level phenomena, such as nucleation, carbon precursor adsorption, and surface diffusion of adatoms, is imperative to exert precise control over the growth process. Concerning the synthesis of VGNWs, hydrogen plays a dual role in the graphene growth process, acting as both a co-catalyst and an etchant for the nanowalls. Nevertheless, a thorough comprehension of the intricate growth process is still required. To address these knowledge gaps, this review paper aims to investigate the nucleation and growth of VGNWs using PECVD, with a specific focus on exploring the temperature effect on the graphene growth ratio and nucleation density across a wide range of temperatures. By providing valuable insights into the PECVD process, our objective is to enable the optimization of growth conditions for tailoring VGNWs' properties, thereby facilitating their application in energy storage, catalysis, and sensing fields.

Human pegivirus (HPgV) is best known for persistent, presumably non-pathogenic, infection and a propensity to co-infect with human immunodeficiency virus or hepatitis C virus. However, unique at-tributes, such as the increased risk of malignancy or immune modulation, have been recently recognized for HPgV. We have identified a unique case of a woman with high levels HPgV infection in two preg-nancies, which occurred 4 years apart, without evidence of human immunodeficiency virus or hepatitis C virus infection. The second pregnancy was complicated by congenital heart disease. A high level of HPgV infection was detected in maternal blood from different trimesters by RT-PCR and identified as HPgV type 1 genotype 2 in both pregnancies. In the second pregnancy, the decidua and intervillous tissue of the placenta were positive for HPgV by PCR but not the chorion or cord blood (from both pregnancies), suggesting no vertical transmission despite high levels of viremia. The HPgV genome sequence was remarkably conserved over the 4 years. Using VirScan, sera antibodies for HPgV were detected in the first trimester of both pregnancies. We observed the same anti-HPgV antibodies against the non-structural NS5 protein in both pregnancies, suggesting a similar non-E2 protein humoral immune response over time. To the best of our knowledge, this is the first report of persistent HPgV infection involving placental tissues with no evidence of vertical transmission. Our results reveal a more elaborate viral-host interaction than previously reported, expand our knowledge about tropism, and opens avenues for exploring the replication sites of this virus.

Default aerosol extinction coefficient profiles are commonly used instead of measured profiles in radiative transfer modelling, increasing the uncertainties in the simulations. The present study aims to determine the magnitude of these uncertainties and contribute towards the understanding of the complex interactions between aerosols and solar radiation. Default, artificial and measured profiles of the aerosol extinction coefficient are used to simulate the profiles of different radiometric quantities in the atmosphere for different surface, atmospheric, and aerosol properties and for four spectral bands: ultraviolet-B, ultraviolet-A, visible, and near infrared. Case studies are performed over different areas in Europe and North Africa. Analysis of the results shows that under cloudless-skies, changing the altitude of an artificial aerosol layer has minor impact on the levels of shortwave radiation at the top and the bottom of the atmosphere, even for high aerosol loads. Differences up to 30% were however detected for individual spectral bands. Using measured instead of default profiles for the simulations leads to more significant differences in the atmosphere, which become very large during dust episodes (10 – 60% for actinic flux at altitudes between 1 and 2 km, and up to 15 K/day for heating rates depending on site and solar elevation).

The basic equation for estimating the aerodynamic power captured by an Anderson Vertical Axis Wind Turbine (AVAWT) is a solution of the Navier-Stokes(N-S) equations for a baroclinic, inviscid flow. In a nutshell, the pressure difference across the AVAWT is derived from Bernoulli’s equation; an upshot of the integration of the N-S momentum equation for a baroclinic inviscid flow, Euler’s momentum equation. The resulting expression for the pressure difference across the AVAWT rotor is plotted as a function of freestream speed. Experimentally determined airstream speeds at the AVAWT inlet and outlet, coupled with corresponding freestream speeds are used in estimating the aerodynamic power captured. The aerodynamic power is subsequently used in calculating the aerodynamic power coefficient of the AVAWT. The actual power coefficient is calculated from the power generated by the AVAWT at various free stream speeds and plotted as a function of the latter. Experimental results show that, at all free stream speeds and tip speed ratios, the aerodynamic power coefficient is higher than the actual power coefficient of the AVAWT. Consequently, the power generated by the AVAWT prototype is lower than the aerodynamic power captured, given the same inflow wind condition.

The aim of work is to derive an explicit expression for a function of vertical mixing induced by wind-waves. To this end, in the Navier-Stokes equations, a current is decomposed into four constituents: the mean flow, the wave-orbital motion, the wave-induced turbulent and the background turbulent currents. This decomposition allows separating the wave-induced Reynolds stress, Rw, from the background one, Rb. To make a statistical closure for Rw, the Prandtl approach for the background turbulent fluctuations is used that results in an implicit expression for the wave-induced vertical mixing function, Bv. Expression for Bv is specified based on the author’s results for the eddy viscosity found earlier in the frame of the three-layer concept for a wavy air–sea interface, used for modelling wind-drift currents [1]. Finally, the explicit parameterization for Bv(a, u*, z) is found as a linear function in both the wave amplitude at depth z, a(z), and the friction velocity in the air, u*. The linear dependence of function Bv(a) on the wave amplitude provides the enhanced vertical mixing induced by wind–waves in comparison with function Bv(a) having the cubic dependence found in [2], as far as the wind-wave amplitude a(z) decays exponentially with depth.

A typical river-connected lake, Jinshan Lake, was selected as the study area. By the combination of field experiment, laboratory experiment and mathematical model, we plotted the relationship between the concentration of DCu-SCu and FDI, and constructed the mathematical model of the migration and transformation of HMCu in Jinshan Lake. We choose a typical diurnal tide to simulate and revealed the vertical migration characteristics of HMCu in Jinshan Lake during a diurnal tide. The results show that: (1) The release rate of DCu was proportional to FDI and background content, respectively. (2) Due to the nearby industrial enterprises and terrain characteristics, SA loads the most HMCu, the average concentration is 70.07mg/kg. According to the characteristics and geographical location of LC, the concentration of copper in the two states fluctuates greatly (DCu: 43.20~74.77 mg/kg, SCu: 53.63~74.67mg/kg). The fluctuation trend of SCu in ZA is significantly different from that in other areas, which mainly due to the complex hydraulic distribution and the sorption-desorption process of HMs in sediment particles. The hydraulic disturbance of JG is the least and relatively stable, which is the farthest from the inlet of the lake and is the least affected by the Yangtze river. (3) The FDI in a diurnal tide reaches the suspension condition of fine sediment particles in each region. FDI and sediment concentration on the vertical exchange of two - state Cu is significant.

The excessive vibration caused by crowds walking across footbridges has attracted great public concerns in the past few decades. This paper presents, from considering the dynamic characteristics of the bipedal crowd model, a new stability limit criterion based on the bipedal excitation model. The stability limit can be used to estimate the upper boundary of crowd size. In addition, the dynamic stable performances of a structure, under a certain walking crowd size, can be predicted by the stability criterion. This proposed mechanism provides an alternative comprehension how crowd excite the excessive sway motion with a large-span structure.

Vertical-axis wind turbines (VAWTs) are receiving more and more attention as they involve simple design, cope better with turbulence and are insensitive to wind direction which has a huge impact on the cost since the yaw mechanism is not needed. However, VAWTs still suffer from low conversion efficiency. As a results tremendous efforts are exerted to improve its efficiency which mainly focus on two methods regardless of whether the study is a CFD simulation or a field test or lab test experiment. An active approach which involves the modification of the rotor itself such as the blade design, angle, trailing and leading edges, inner blades, chord thickness, contra-rotating rotor, etc. While the second approach involves passive techniques where the flow is directed to optimally face the downwind rotor by mounting a guiding vane such as a diffuser or other shapes at the upwind position of the rotor. Among all techniques undertaken, the CRWT rotor technique seems to be the most effective with an output even comparable to that of Horizontal Axis Wind Turbines (HAWT), while the Savonius rotor received more attention compared to other designs of VAWTs. Apart from technological issues, it was also suggested that geographical issues such as proper site siting of the wind turbine rotor at a particular location where a uniform flow could be guaranteed is of paramount importance to ensure an effective conversion capacity of wind turbines.

A novel drive current model covering the effects of source/drain voltage (VDS) and gate voltage (VGS) and incorporating drift and diffusion current on the surface channel at the nano-node level, especially beyond 28nm node is presented. The effect of the diffusion current added is more satisfactory to describe the behavior of the drive current in nano-node MOSFETs, fabricated with the atomic-layer-deposition (ALD) technology. This breakthrough in model establishment can expose the long and short channel devices together. Introducing the variables of VDS and VGS, the mixed current model more effectively and meaningfully demonstrates the drive current of MOSFETs under the operation of horizontal, vertical, or mixed electrical field. In comparison between the simulation and experimental consequences, the electrical performance is impressive. The error between both is less than 1%, better than the empirical adjustment to issue a set of drive current models.

Optimizing the NACA0015 airfoil which is widely applied in small-scale vertical axis wind turbine to make it has a better aerodynamic performance. In the optimization process, using CST parameterization method to perturb the airfoil geometry, the thickness and camber of the airfoil are selected as the constraint, and the value of the maximum tangential force coefficient is chosen as the objective function, the genetic algorithm based on non-dominated sorting (NSGA-II)is selected as an optimization method, calculates the aerodynamic performance of the airfoil by applying the approach of combining XFOIL program and Viterna-Corrigan post-stall mode ,and establishes the optimizing process by the optimization software modefrontier for NACA0015 airfoil’s muti-point optimization, validate the airfoil’s performance with CFD finally. The result illustrates that, by comparing with the NACA0015 airfoil, the optimized airfoil’s lift to drag ratio is improved over a wide range of attack angles, the stall performance is more gentle. The maximum lift coefficient, the maximum lift-drag ratio and the maximum tangential force coefficient are increased by 7.5%,9 and 8.87%, respectively. The optimized airfoil has a wide variable condition performance, more suitable for the operating conditions of a vertical axis wind turbine. Finally, predict the rotor efficiency with optimized airfoil and NACA0015 airfoil for different tip speed ratios and different solidities with multiple streamtube model, the result shows the rotor with optimized airfoil has a higher efficiency.

The objective of this work was to investigate the effect of different soil tillage practices in sunflower cultivation in a rotation system with intercropping Triticosecale x Pisum sativum. For this purpose a two year experimental field of 5% slope was established in central Greece. There were four treatments with three replications each. The treatments were: (a) no tillage - planting parallel to the contour (NTC-PAC), (b) conventional tillage - planting parallel to the contour (CTC-PAC), (c) no tillage - planting perpendicular to the contour (NTC-PEC), (d) conventional tillage - planting perpendicular to the contour (CTC-PEC). During the experiment plant height, leaf area index, specific leaf area, plants’ total nitrogen and plants’ proteins were measured. According to the results plant height ranged from 64.9 (CTC-PAC) to 85.2 cm (NTC-PEC) the 1st year and between 66.5 – 86.5 cm in CTC-PAC and NTC-PEC treatments in the 2nd year. Furthermore, LAI and SLA, plant’s total nitrogen and protein content and N-uptake were affected positively by the no tillage practice. To conclude, sunflower is a promising crop in a rotation system with intercropping Triticosecale x Pisum sativum, cultivating under rainfed sloping conditions.

For deep-penetrating geochemistry, there is a frontier issue as to how to explore ore-bearing information deep in covered areas, while it is, too, important to investigate the geochemical migration of ore-forming elements for the development of exploration geochemistry. In this study, a 380-day migration column experiment was conducted with surface soil and pure Cu powder collected from the Yujiashan study area in Wuhan City, Hubei Province taken as the object of research to simulate the migration process of ore-forming elements under natural conditions. The results showed obvious vertical migration of the ore-forming elements and conversion of mobile metal forms in the process; further, according to 6 groups of simulation experiments that took 45 days to conduct on migration column samples and the surface oil and Cu powder collected from the Pulang mining area in Yunnan Province, the vertical migration of the ore-forming element was still visible, and the exogenous substance (pure Cu powder) could enhance the anomaly without changing the basic migration mechanism. This indicates that Cu might migrate in a stable manner in soil cover in the Pulang mining area, and its migration was mostly driven by the transformation of Fe-Mn oxide bound state and organic bound state; finally, a multifractal analysis was conducted, revealing that the ore-forming elements presented a nonlinear and complex structure during their upward migration, which caused anomalies in the covered area, and multiple parameters exerted a certain indicative effect on different source intensities and properties of soil. In this study, laboratory simulations were performed to summarize the active-state evolution pattern and migration mechanism of ore-forming elements with a view to providing technical support and theoretical guidance for geochemical prospecting in the covered region.

Weaving technology can convert two-dimensional structures such as ribbons into three-dimensional structures by specific connections. However, most of the 3D structures fabricated by conventional weaving methods using straight ribbons have some topological defects. In order to obtain smoother continuous 3D surface structures, Baek et al. proposed a novel weaving method using naturally curved (in-plane) ribbons to fabricated three-dimensional curved structures and using this method to weave new spherical weave structures that are closer to perfect spheres. We believe that this new spherical weave structure with smooth geometric properties must correspond to new mechanical properties. To this end, we investigated the buckling characteristics of different types of spherical weave structures by the combination of test and finite element method. The results of calculations and experiments show that the failure mode of the spherical weave structure under vertical loading can be divided into two stages: a flat contact region forms between the spherical weave structure and the rigid plate and inward dimple of ribbons. The spherical weave structures using naturally curved (in-plane) ribbon weaving have better buckling stability than those woven with straight ribbons. The vertical buckling load of spherical weave structures using naturally curved ribbon increases with the width and thickness of the ribbon. In addition, this paper combines test, theoretical and finite element analysis to propose the buckling load equation and buckling correction factor equation for the new spherical weave structure under vertical compression load.

Drilling vibrations has been identified as a key performance limiter that prevents successful energy transfer from the surface to the bit. The resultant irregular bit rotation speed causes drilling challenges like poor hole quality and reduction in rate of penetration to name a few. Amongst other vibration suppression techniques, active control of vibrations is widely used and recommended. Active control system utilizes a closed loop feedback control to continuously adapt to downhole vibrations detected at the surface. The system requires regular tuning and upgrades which is done experimentally before field deployment. The paper presents a PID based experimental tuning of horizontal and vertical strings for irregular RPM. In doing so, the paper highlights the need of having horizontal experimental setups for state-of-the-art PID tuning for downhole RPM. The settling time of irregular RPM for horizontal setup is found to be lower than the vertical configuration due to multiple contact points and increased friction coefficient.

It is important to understand the statistical-physical structure of the rain in the vertical so that observations aloft can be translated meaningfully into what will occur at the surface. In order to achieve this understanding, it is necessary to gather high temporal and spatial resolution observations of rain in the vertical. This can only be accomplished using radars. It can be achieved by translating radar Doppler spectra into drop size distributions which can then be integrated to calculate variables such as the rain fall rate. A long-standing difficulty in using such measurements, however, is the problem of vertical air motion which can shift the Doppler spectra, and, therefore, significantly alter the deduced drop size distributions and integrated variables. In this work, we illustrate the improvement in measured rain structures using a new approach for removing the effect of mean vertical air motion. It is demonstrated that the new approach proposed here not only produces what appear to be better estimates of the rainfall rates, but, also as a consequence, provides estimates of the temporal and spatial regionally coherent updraft and downdrafts occurring in the precipitation. Furthermore, the technique is readily applicable to other radars especially those operating at non-attenuating frequencies.

Selection of appropriate friction factors is paramount for accurate prediction of key flow characteristics in gas–liquid two-phase flows. In this work, experimental investigation of vertical air and oil (with viscosities up to 200 mPa s) flow in a 0.060-m ID pipe is reported. Superficial air and oil velocity ranges utilized are from 22.37 to 59.06 m/s and 0.05 to 0.16 m/s respectively. The influence of estimation of interfacial friction factor on accurate determination of film thickness, void fraction and pressure gradient was investigated using a two-fluid model. The results indicated that the two-fluid model is capable of accurately predicting flow characteristics. Further, it reveals that the best performing correlations are the Belt et al. and Ambrosini et al. correlations.

To investigate the optimum layouts of small vertical axis wind turbines, a two-dimensional analysis of dynamic fluid body interaction is performed via computational fluid dynamics for a rotor pair in various configurations. The rotational speed of each turbine rotor (diameter: D = 50 mm) varies based on the equation of motion. First, the dependence of rotor performance on the gap distance (gap) between two rotors is investigated. For parallel layouts, counter-down (CD) layouts with blades moving downwind in the gap region yield a higher mean power than counter-up (CU) layouts with blades moving upwind in the gap region. CD layouts with gap/D = 0.5–1.0 yield a maximum average power that is 23% higher than that of an isolated single rotor. Assuming isotropic bidirectional wind speed, co-rotating (CO) layouts with the same rotational direction are superior to the combination of CD and CU layouts regardless of the gap distance. For tandem layouts, the inverse-rotating configuration (IR) shows an earlier wake recovery than the CO configuration. For 16-wind-direction layouts, both the IR and CO configurations indicate similar power distribution at gap/D = 2.0. For the first time, this study demonstrates the phase synchronization of two rotors via numerical simulation.

The global energy crisis has lead researchers explore other sources of energy like wind, resulting in a wide acceptance of wind turbines. Vertical axis wind turbines (VAWT) more suitable for small scale application in urban conditions than their horizontal-axis counterparts. A Helical bladed VAWT would reduce the ripple effect when compared to Straight bladed VAWT. The effect of the blade helix angle on the aerodynamic performance of VAWT using 3D numerical simulations is studied. Turbulence modelled using 4-Equation transition SST k-w model. Three different helix angles of 60, 90 and 120 of a 3 bladed VAWT operating across different tip speed ratios were studied. The 60 helical bladed VAWT was found to perform better than all other helical bladed and straight bladed VAWT. Standard deviation of the moment coefficient generated by a blade plotted against 360 of azimuth rotation revealed that the ripple effect on the shaft produced by cyclic loading of the straight blade is considerably reduced upon introduction of helix angle, with 120 helical blade giving lowest standard deviation. The analysis has been done for the percentage of power generated by each quartile of flow and the contribution of each section of the blade. A comparative study was also conducted between different helical bladed VAWT and straight bladed VAWT. Flow feature analysis also revealed the reasons behind secondary peaks and the performance improvement when tip speed ratio increases. Wake structure analysis and flow contours were also studied for a better understanding of the flow field.

We describe the design and construction of coils to compensate the earth's magnetic field in the vertical cryostat GERSEMI in the FREIA laboratory at Uppsala University.

The world is facing several global issues such as food and energy crisis, climate change and greenhouse gases emissions. To subdue these issues, many entities from academia and industries have innovated alternate techniques of performing regular activities which cause such problems. One of these innovations is the introduction of vertical and zero acreage farming in the field of sustainability. These carry the potential to solve one of the most important affairs of food security in most countries of the world. But, this technology has been in its nascent stage for many years. This paper uses a comprehensive framework proving the feasibility of initiating vertical farming on university campuses to feed the staff and students, which could also set an example to the rest of the world into using this technique on a wider scale. The study chose Huazhong University of science and technology (HUST) in Wuhan city, China for accessing the return on investment and food sufficiency if vertical farming is implemented. Using Central Limit Theorem, a statistical model was developed, and various scenarios were analyzed. The results indicated that if a separate vertical farm is constructed, the breakeven can be achieved in a range of 10-20 depending on parameters such as type of operation, number of floors and amount of vegetation. The study has shown that the use of vertical farming cannot only bring in revenue for the campus but also aid in mitigating climate change.

The digital elevation model (DEM) is one of the key geospatial datasets used in many fields of engineering and science for countless applications. In this contribution, we assess the vertical accuracy of the Advanced Land Observing Satellite (ALOS) World 3D-30m (AW3D30) DEM using the runway method (RWYM). The RWYM utilizes the longitudinal profiles of runways which are reliable and ubiquitous reference data. A reference dataset used in this project consists of 36 runways located at various points throughout the world. The same dataset was previously used to test the accuracy of WorldDEM^TM. Our study indicates that AW3D30 has a remarkably high RMSE of 1.78 m (one σ). However, while analyzing the results, it has become apparent that it also contains a widespread elevation anomaly. We conclude that this anomaly is the result of uncompensated sensor noise and the data processing algorithm (downsampling of the higher resolution data). We believe that this issue should be communicated to the user community. Also, we would like to note that the traditional accuracy assessment of a DEM, e.g., statistical assessment of the elevation differences = model – reference, does not allow for identification of these type of anomalies in a DEM.

This paper studies ionospheric vertical total electron content (VTEC) variations before the 2014 Mw8.2 Chile earthquake. VTEC derived from 14 GPS (Global Positioning System) stations and GIM (Global Ionospheric Map) were used to analyze ionospheric variations before the earthquake using the sliding interquartile range method, and results showed that significant positive VTEC anomalies occurred on 28 March. To explore possible causes of these anomalies, effects of solar and geomagnetic activities were examined, and VTEC variations during 17 March to 31 March in 2009-2013 were cross-compared. Also, VTEC for a full year before the earthquake was investigated. Results indicated that these anomalies were weakly associated with high solar activities and geomagnetic storms and that these anomalies were not normal seasonal and diurnal variations. An analysis of the spatial distribution of the observed anomalies was also presented, and it demonstrated that anomalies specifically appeared around the epicenter on 28 March. It suggests that observed anomalies may be associated with the subsequent Chile earthquake. Equatorial anomaly variations were analyzed to discuss the possible physical mechanism, and results showed that the equatorial anomaly unusually increased on 28 March, which indicates that anomalous electric fields generated in the earthquake preparation area and the meridional wind are possible causes of the observed ionospheric anomalies.

The goal of this study was to develop a rapid diagnostic kit for rheumatic disease and systemic lupus erythematosus (SLE) screening. A novel rapid vertical flow assay (VFA) was engineered and used to assay anti-nuclear (ANA) and anti-dsDNA (αDNA) autoantibodies from systemic lupus erythematosus (SLE) patients and healthy controls (HC). Observer scores and absolute signal intensities from the VFA were validated by ELISA. The rapid ten minute point of care VFA test engineered demonstrated a limit of detection of 0.5 IU/ml for ANA and αDNA autoantibodies in human plasma with inter-operator CV of 19% for ANA and 12% for αDNA. Storage stability was verified over a three-month period. When testing anti-dsDNA and ANA levels in 22 SLE and 18 HC serum samples, the duplex VFA revealed 95% sensitivity, 72% specificity and 84% accuracy in discriminating disease groups, comparable to the gold standard, ELISA. The rapid αDNA/ANA duplex VFA can potentially be used in primary care clinics for evaluating patients or at-risk subjects for rheumatic diseases and for planning follow-up testing. Given its low cost, ease and rapid turnaround, it can also be used to assess SLE prevalence estimates.

The altimeter-derived ocean currents have been sparsely evaluated against in situ measurements in the Arctic, particularly for extended time periods. This study uses the extensive mooring array situated in the Fram Strait, representing one of the longest ocean current records, to investigate the relationship between in situ and satellite-derived currents in the region. The primary objective of this research is to analyze the vertical structure of the West Spitsbergen Current (WSC), its spatio-temporal coherence, and its association with surface geostrophic currents during the period of 1997-2012. To assess the vertical structure of the WSC, we utilized the Empirical Orthogonal Functions (EOF) and cross-correlation analysis between neighboring moorings. Remarkably, both velocity components exhibited robust vertical coherence, particularly within the waters of the North Atlantic Inflow, at depths exceeding 800 m. These findings underscore the potential for surface measurements to effectively complement data gaps and facilitate the reconstruction of deeper currents with a monthly temporal resolution. Notably, the surface measurements explain approximately 67% of the variance in the top 800 m of the water column.This comprehensive investigation advances our understanding of the West Spitsbergen Current and its vertical characteristics in the Arctic. Moreover, our findings highlight the valuable synergy between in situ and satellite-derived data, providing critical insights for future ocean current studies in this ecologically sensitive region.

This research explores the application of Support Vector Machine (SVM) and Digital Surface Models (DSM) derived from Unmanned Aerial Vehicle (UAV) data for a vertical-horizontal classification of mangrove ecosystems in Tongke-tongke and Samataring Village. The study focuses on integrating high-resolution DSM subtracted from Digital Terrain Models (DTM) to classify mangrove vegetation into sixteen distinct vertical-horizontal classes based on vegetation type and elevation. The analysis revealed that older mangroves, particularly those within the 25-35 meters elevation range, dominate the landscape, accounting for 43.40% of the total classified area. This dominance suggests a mature and ecologically stable mangrove ecosystem, which is crucial for biodiversity conservation and carbon storage. The study demonstrates the effectiveness of SVM and UAV technologies in providing detailed and accurate ecological assessments of mangrove forests. The classification results contribute valuable insights into the structural diversity and health of mangrove ecosystems, facilitating targeted conservation and management strategies. Additionally, the research highlights the utility of advanced remote sensing and machine learning techniques in enhancing the precision of environmental monitoring and the assessment of carbon sequestration capabilities within mangrove ecosystems. The findings underscore the potential of UAV-based remote sensing for ecological studies, offering a replicable method for similar assessments in other regions, thereby supporting global environmental management and climate action initiatives.

Recently, a high internal surface of the titanium alloy pipe is required due to the increment of various applications of the pipe such as aerospace. However, the traditional machining process is unable to effectively polish the internal surface of the slender pipe. Thus, a vertical magnetorheological polishing (VMRP) apparatus is carried out in this work to implement high polishing performance on the internal surface of the titanium alloy pipe. The polishing process is realized by the combination of the rotating motion of the pipe and the reciprocating linear motion of the polishing head. Moreover, a series of comparative experiments are conducted to investigate the polishing mechanism of magnetorheological (MR) fluid and enhance the polishing performance. It is shown from the experimental results that proposed VMRP approach exhibits the better polishing performance than the conventional horizontal MR polishing method under same testing conditions. This is because the proposed VMRP method well eliminates the traces of polishing particles owing to the combination of polishing particles with different sizes. In addition, it is identified from the experimental test that the polishing time of the VMRP required to achieve the same polishing effect as the conventional method is shortened under the combination of different rotation speeds. It is identified from the above benefits of the VMRP that the final surface roughness after polishing is below 0.05 μm.

The cost effective design of tidal turbines requires a good estimation of the loading cycles and their extrema that are related to the unsteady fluctuations of the current velocity. Apart from the ambient turbulence, the main source of velocity fluctuations is the presence of surface waves. In the present study, we analyse the effect of waves propagating against the current on the performance and the loads of a twin vertical axis tidal turbine by an experimental approach at a 1/20 scale. Overall, the results show little or no effect of the waves on the average power and loads compared to the condition with current only, but a significant impact on their standard deviation that rises linearly with the waves amplitude. The drag, lift and pitching moment show extended ranges up to 7.5 times higher and extreme values exceedance by 60 to 100 % with irregular waves compared to the condition without waves. Those load and power fluctuation increase are fully due to the presence of waves as the coherence function between the rotor torque or the loads and the velocity spectra exceed 0.5 on the whole wave frequency bandwidth. The results also reveal a rotational sampling of the waves by the rotors that had also been observed on horizontal axis turbines. From a structural design point of view, the authors recommand to conduct tests in irregular wave conditions as the loads range and extreme values are 1.5 to 2 times higher than those encountered with regular waves of the same significant height and period.

Abstract：Ballast pick-up velocity is a crucial parameter in the design of a slurry system in excavating devices, it influences transportation stability, safety, and economy of the system. In this study, a vertical pipe hydraulic experiment with different ballast sizes under water condition was conducted to investigate the ballast pick-up velocity in the shield slurry system. Thereafter, the coupling method of computational fluid dynamics and the discrete element method (CFD-DEM) was employed to establish a numerical model of the ballast pick-up velocity in the shield slurry system, and its applicability was verified by comparing the experiment results. Additionally, the ballast pick-up process under actual working conditions was studied, and the influence of ballast size and concentration on pick-up velocity was investigated. Overall, the primary findings of the study are as follows: 1) The numerical method can be applied to predict both the single ballast and ballast group pick-up velocity. 2) The pick-up process of the ballast group can be divided into four stages. 3) The conveying velocity of the ballast should be higher than the pick-up velocity of the single ballast to facilitate smooth discharge. 4) For a certain increase in ballast concentration, the pick-up velocity tends to be stable.

Minirhizotron tubes were installed to monitor root growth dynamics of mature Shiraz grapevines in a rootstock trial established in the hot climate Riverina region of New South Wales, Australia. The vertical root distribution and seasonal root growth dynamics of Shiraz on own-roots and Shiraz grafted on the rootstocks Ramsey, 140 Ruggeri and Schwarzmann was studied for five seasons across a seven-year period to a depth of 60 cm. New root production was significantly influenced by genotype, soil depth, season, growth stage and year. Soil moisture and soil tem-perature were monitored at 10, 30 and 60 cm in the last two seasons. Soil moisture at 30 cm and soil temperature at all three depths were significant predictors of root growth. New root numbers were significantly higher in 140 Ruggeri than the other rootstocks. To the depth studied, 140 Ruggeri roots were evenly distributed from the topsoil down, whereas the majority of roots of Schwarzmann and Shiraz were located at intermediate depths in the 10-40 cm ad 20-40 cm zones respectively, while Ramsey roots were found at 20 cm or below. Depending on genotype, root growth occurred across several phenological stages but tended to peak at flowering. In some years we observed root growth in early and late winter at rates exceeding that of autumn, and this was associated with warmer temperatures during this period. Overall, seasonal rooting dynamics were responsive to abiotic factors but dominated by genotype.

The formation and localization of sporadic E(Es) layers predicted by the ions vertical drift velocity and its vertical change in the lower thermosphere during nighttime are shown analytically and by numerical simulations. The consideration of existence of a minimum negative value of the vertical change of the ions vertical drift velocity as a necessary condition of formation of Es layer and determining ions convergence rate into this layer, is extended in case of the presence of vertical wind. Upward vertical wind can shift the convergence regions upward, while downward vertical wind shift them downward, unlike the cases of presence of only meridional and zonal winds. It also changes the ion convergence rate compared to the one with just a horizontal wind. It is shown for the first time that the upward constant wind also causes the convergence of ions with maximum rate in the region where the ion-neutral collision frequency is equal to their cyclotron frequency. While demonstrating the presented theory by numerical simulations, HWM14 data is used for the meridional and zonal wind velocity profiles and the presence of its vertical component is assumed. In this case, in addition to the estimated ion drift velocity and its vertical changes, their initial distribution and ambipolar diffusion also determine the development of ion convergence/divergence processes. For small magnitude of vertical wind velocity, its significant influence on the ions/electrons behavior is demonstrated, which shows the importance of both tidal wind and wind changes caused by the propagation of atmospheric gravity waves on the formation of the Es layer. In this theoretical research it is shown that the realistic profile of the wind velocity, which takes into account the vertical component along with its zonal and meridional ones, is important for prediction of the Es layers formation, as well as regions of ion depletion.

Pelagic stingray (Pteroplatytrygon violacea) is the only species of stingray (Dasyatidae) that utilizes both pelagic and demersal habitats. It is the main bycatch species in pelagic longline fisheries targeting bluefin tuna in the Gulf of Lions. In the Mediterranean Sea, their stock structure, behavioural ecology and movements are unknown. For the first time in the Mediterranean, 17 individuals (39 to 60 cm disc width) were tagged with pop-up satellite archival transmitting tags using a novel method of tag attachment, to investigate horizontal and vertical movements. The tags were attached for between two and 60 days. Between the months of July and October, pelagic stingray occupied a temperature range of 12.5 to 26.6°C, and a depth range extending from the surface to 480 m. Monthly trends in catch-per-unit-effort (CPUE) of pelagic stingray peaked in August and decreased by late autumn. Pelagic stingray may aggregate on the continental shelf during summer, and move southwards in early autumn, and this movement pattern is considered in relation to the reproductive cycle and overwintering. Future work and options for bycatch mitigation are discussed.

We studied peat stratigraphy at the Mukhrino peatland, which is a typical ombrotrophic bog for the middle taiga zone of Western Siberia, to gain insights about its history, hydrology and carbon fluxes. Seven cores were collected from locations chosen to represent the typical present-day vegetation types, for dating of separated dissolved (DOC) and particulate (POC) organic carbon fractions using the Accelerator Mass Spectrometer (AMS) radiocarbon ($^{14}$C) method. The oldest peat was found at the bottoms of an underlying lake (10,053 cal. year BP) and an ancient riverbed (10,989 cal. year BP). For the whole history of the peatland the average peat accumulation rate was estimated to be 0.067±0.018 cm yr-1 (0.013-0.332 cm yr-1) and the carbon accumulation rate was 38.56±12.21 g m-2yr-1 (28.46–57.91 g m-2 yr-1). There were clear age differences between the separated samples of DOC and POC. DOC was older than POC in the uppermost 150 cm of the peat deposit, and younger in the deeper layers. The difference in age increased with depth, reaching 2,000–3,000 years at the bottom of the peat deposit (depth 430--530 cm). Following consideration of a range of factors that could potentially cause the dating discrepancy, we hypothesised that DOC continuously moves down into the mineral sediment beneath the peat, as an additional carbon flux that results in mixing of younger and older carbon. On this basis we estimated the apparent rate of DOC downward movement and the associated rate of carbon loss. The first estimate of the average rate of DOC downward movement in Western Siberia is 0.047±0.019 cm yr-1.

This research investigates the effects of torsional moments on the mechanical behavior of thin-walled open-ended vertical pile foundations subjected to lateral wind loads. The warping and torsion effect generated over the piles due to the resultant lateral load impact outside the shear center is analyzed in-field tests. Complementarily, a two-dimensional finite element model based on the simple bending stress-strain state as well as a three-dimensional finite element model considering torsional effects were implemented and their results analyzed. Finally, a comparative analysis between the in-field lateral loading tests and the finite element model approaches was established and correlations between the errors and the parameters of influence were highlighted. From the results, it has been ascertained that the slender thin-walled open-ended pile foundations are particularly sensitive to small load deviations from their center of gravity, this leads to the fact that the slenderer and the more eccentricity of the load, the more it affects the torsion and warping of the pile. Calculation methodologies usually consider a simple in-plane bending behavior which conducts to errors between 44 and 58% of the experimental results.

In recent years, there has been a growing interest in the preoperative modeling of fluid-structure interaction in the treatment of cerebral aneurysms. In this study, we investigate two cases involving laminar incompressible fluid flow interacting with hyperelastic materials (a vertical flap and aneurysm walls) under the effect of fluid flow. We present a finite element method (FEM) for these prototypical two-dimensional ($2D$) configurations, taking into account the complex flows and deformation of the variant's structure models. We use an Arbitrary Lagrangian-Eulerian (ALE) formulation in a continuum, fully monolithic coupled way, and discretize the fluid and solid domains using the quadratic LBB stable $P_2P_1$ finite element pair to approximate the displacement, velocity, and pressure spaces independently. The resulting discretized form of the nonlinear algebraic system is linearized using a variant of Newton's procedure, and the Jacobian matrices are approximated via the divided difference method. The resulting linear systems are solved using a direct solver MUMPS. We evaluate hydrodynamic forces such as drag and lift coefficients for nonlinear elastic material models, including Saint-Venant Kirchoff, Neo-Hookean, and Mooney-Rivlin (2 parameters) separately. To gain more physical insight into the problem, we verify the computed results by comparing the velocity, viscosity, and pressure fields. Our aim is to qualitatively analyze the changes in the mechanics of the wall behavior of the elasticity of the flap vs. the complexity of deformation, interface, details for prototypical flow situations, corresponding displacement, and deformation. We also provide a physical interpretation of blood flow magnitude and basic hemodynamic phenomena of wall shear stresses (WSS) in aneurysma and the range of deformation. Overall, this study presents a comprehensive approach to modeling fluid-structure interaction in cerebral aneurysms, which could help in the development of more effective treatment strategies.

A study about influence of heat input on welding defects in vertical upward welding position for dissimilar material and thickness using a new variation of TIG welding torch is done with support of advanced inspection methods SEM and EBSD. With vertical upward welding position, control heat input plays an important role to keep the weld stabilization without defects. On the other hand, TIG welding process using a conventional TIG torch (conventional TIG welding process) has low efficiency and it is difficult to control heat input with high accuracy. So, it is considered that using conventional TIG torch is still a challenge for welding thin plates. In this case, a new variation of TIG torch has been developed. This torch used a constricted nozzle to improve plasma arc characteristics. As a result, it can control efficiently the heat input to prevent the excessive or insufficiency for joining thin sheets. For evaluation of welding quality, advanced examination methods SEM and EBSD were applied to directly observe the welding defects. From the results, the formation mechanism of blowhole inside weld zone in case of welding dissimilar material and thickness was discussed. It is pointed out that when sufficient welding current, the change from weld zone to base metal is uniform, no welding defects such as blowhole was seen. However, in case of low welding current, the thinner base metal is insufficient fusion and the change between weld zone and base metal is not uniform. The blowhole was observed at SS400 material side.

Wind turbines are a solution for sustainable energy, significantly reducing carbon emissions and fostering a circular economy for more cost-effective and cleaner power generation, in line with worldwide environmental aspirations. In this context, this research aims to explore a novel Two-Stage Twisted Blade micro-Vertical Axis Wind Turbine ($\mu$-VAWT) alternative inspired by the Savonius Rotor (SR). This investigation utilizes the $\kappa-\omega$ SST turbulence model to explore the power coefficient ($C_P$) and torque coefficient ($C_T$), finding $C_P$ values ranging from 0.02 to 0.04 across the turbine by altering the free stream velocity ($V$). $C_T$ analysis further delves into four specific sections, highlighting areas of particular interest. These results are validated by examining velocity contours, pressure contours, and streamlines in four horizontal sections, demonstrating that the proposed turbine model exhibits minimal torque fluctuation. Moreover, the analysis of vertical wind streamlines illustrates very low interference with various wind turbine proposals, underscoring the turbine's efficiency and potential for integration into diverse wind energy projects.

Almost contact complex Riemannian manifolds, known also as almost contact B-metric manifolds, are in principle equipped with a pair of mutually associated pseudo-Riemannian metrics. Each of these metrics is specialized here as a Yamabe almost soliton with a potential collinear to the Reeb vector field. The resulting manifolds are then investigated in two important cases with geometric significance. The first is when the manifold is of Sasaki-like type, i.e. its complex cone is a holomorphic complex Riemannian manifold (also called a Kähler–Norden manifold). The second case is when the soliton potential is torse-forming, i.e. it satisfies a certain recurrence condition for its covariant derivative with respect to the Levi-Civita connection of the corresponding metric. The studied solitons are characterized. In the three-dimensional case, an explicit example is constructed and the properties obtained in the theoretical part are confirmed.

An interesting physical phenomenon was recently observed when a fresh-water basin is covered by a thin ice film that has properties similar to that of a rubber membrane. Surface waves can be generated under the action of wind on the air-water interface that contains an ice film. The modulation property of hydro-elastic waves (HEWs) in deep water covered by thin ice film blown by the wind with a uniform vertical profile is studied here in terms of the air-flow velocity versus a wavenumber. The modulation instability of HEWs is studied through the analysis of coefficients of the nonlinear Schrödinger (NLS) equation with the help of the Lighthill criterion. The NLS equation is derived using the multiple scale method in the presence of airflow. It is demonstrated that the potentially unstable hydro-elastic waves with negative energy appear for relatively small wind speeds, whereas the Kelvin–Helmholtz instability arises when the wind speed becomes fairly strong. Estimates of parameters of modulated waves for the typical conditions are given.

The Oldroyd–B model for a linear viscoelastic fluid is employed to investigate the buoyant flow in a vertical porous layer with permeable boundaries kept at different uniform temperatures. Seepage flow in the viscoelastic fluid saturated porous layer is modelled through an extended version of Darcy’s law taking into account the Oldroyd–B rheology. The basic stationary flow is parallel to the vertical axis and describes a single–cell vertical pattern where the cell has an infinite vertical height. A linear stability analysis of such a basic flow is carried out to determine the onset conditions for a multicellular pattern. The neutral stability curves and the values of the critical Rayleigh number are evaluated numerically for different retardation time and relaxation time characteristics of the fluid.

Light microscopy is indispensable for analysis of bacterial spatial organization. However, imaging in bacteria is difficult due to their small sizes and the fact that most species are non-spherical, meaning they typically lie horizontally on a microscope coverslip. This is especially problematic when considering that many essential bacterial processes—such as cell division—occur along the short axes of these cells, and so are viewed side-on by standard microscopy. We recently developed a pair of methods to overcome this problem by forcing cells to stand vertically during imaging, named VerCINI (Vertical Cell Imaging by Nanostructured Immobilisation) and µVerCINI (Microfluidic VerCINI). The concept behind both methods is that cells are imaged while confined vertically inside cell traps made from a nanofabricated mould. By doing so, the short axes of the cells are rotated parallel to the microscope imaging plane and are imaged with high resolution. μVerCINI combines the vertical cell confinement with microfluidics so that vertical imaging can be done during fluid exchange, such as during antibiotic perturbations. Here, we provide a practical guide to implementing both VerCINI and µVerCINI, with detailed protocols and experience-based tips so that interested researchers can easily use one or both imaging methods to complement their current approaches.

Drops are the most important and most common energy dissipator in irrigation networks and erodible canals and consequently, their performance must be well understood. This study was designed to evaluate the capability of Artificial Intelligence (AI) methods including ANN, ANFIS, GRNN, SVM, GP, MLR, and LR to predict the relative energy dissipation (∆E/E0) in vertical drops equipped with a horizontal screen. For this study, 108 experiments were carried out to investigate energy dissipation with variable discharge, varying drop height, and porosity of the horizontal screens. Parameters yc/h, yd/yc, and p are considered as input variables and ∆E/E0 is the output variable. The efficiency of models was compared using Taylor's diagram, Box Plot of the applied error distribution, correlation coefficient (CC), mean absolute error (MAE) and root-mean-square error (RMSE). Results indicate that the performance of the ANFIS_gbellmf based model with CC value of 0.9953, RMSE value of 0.0069 and MAE value of 0.0042 was superior to other applied models. Also, the linear regression model with CC=0.9933, RMSE=0.0083, and MAE= 0.0067performs better than the multiple linear regression model in this study. Results of a sensitivity study suggest that yc/h is the most effective parameter for predicting ∆E/E0.

Enhancing the Efficiency of Natural Gas Liquid (NGL) Extraction and Fractionation Trains: An Integrated Approach of Simulation Analysis, Advanced Modifications, and Technological Advancements. Through comprehensive research, innovative solutions such as the heat pump aided distillation (HPAD) system and self-heat recuperation technology (SHRT) have been developed to significantly reduce the energy consumption associated with conventional distillation systems. To identify a practical system for NGL fractionation trains, this study extensively examined and compared various HPAD and SHRT options to retrofit a single column. The objective was to find the most suitable and efficient solution for the fractionation process of natural gas liquids (NGLs). The retrofit options analyzed in this study encompassed a range of techniques, including vapor compression (VC), mechanical vapor re-compression (MVR), thermal vapor re-compression (TVR), bottom flashing (BF), side heat exchanger (SHE), intermediate heating and cooling (IHC), self-heat recuperative (SHR), and modified self-heat recuperative (MSHR) distillation. These methods were carefully examined to determine their suitability and effectiveness in improving the performance of NGL fractionation trains.In this study, a depropanizer column, typically employed in conventional NGL plants, was selected as a case study. The simulation software Aspen HYSYS V7.3 was employed to model and analyze eight retrofit designs based on predefined criteria. The simulation data was carefully evaluated to identify the most efficient design for minimizing energy consumption. Among the retrofit options, the mechanical vapor re-compression (MVR) technique demonstrated the most significant energy cost reduction, with a remarkable 68.11 percent improvement compared to the base case conventional column. These findings highlight the potential of MVR as an effective solution for lowering energy costs in NGL fractionation trains.Following the MVR retrofit option, the study found that vapor compression (VC) achieved a considerable energy cost reduction of 66.65 percent, closely followed by modified self-heat recuperative (MSHR) at 64.02 percent, bottom flashing (BF) at 62.88 percent, self-heat recuperative (SHR) at 55.85 percent, side heat exchanger (SHE) at 54.23 percent, intermediate heating and cooling (IHC) at 39.54 percent, and thermal vapor re-compression (TVR) also at 39.54 percent. These findings highlight the significant potential for energy savings offered by these retrofit options, with VC being the most popular choice, closely followed by MSHR, BF, SHR, SHE, IHC, and TVR.

The wind observations for multiple levels (40–200 m) have been conducted for a long time (2016–2020) on Jeju Island of South Korea. This study aims at understanding the vertical and temporal characteristics of lower atmosphere. Jeju Island is a region located at mid-latitude and is affected by seasonal monsoon wind. The maximum wind speed appears in the lower layer during day time and is delayed in the upper layer during latter time in diurnal cycle. In summer season, the surface layer increases up to 160 m during day time via dominant solar radiation effect, which is higher than those for other seasons. However, the maximum wind speed in winter season appears irregularly among altitudes, and the surface layer is ~100 m, which is lower than that in summer season. It can be attributed to the increase in the mean wind speed in diurnal cycle caused by the strong northwestern wind for winter season. These results imply that the relationship between near-surface and higher altitudes is primarily affected by solar radiation and seasonal monsoon winds. These results are expected to contribute to site selection criteria for wind farms and to the assessment concerning planetary boundary layer modeling.

In this study, grapevine was used as the research material. This plant which epitomizes the opinion that vertical gardens can have a positive influence on human psychology with their beautiful view, e.g., the hanging gardens of Babylon about 2500 years ago. The study in question was conducted in 2016 at Bingol University, Faculty of Agriculture, the Department of Garden Plants research and application area. The offshoot growth was measured in a fertilizer experiment that formed the control, first application (200 g/100 L water, leaf) and second application (100 g/100 L water + 20% leaf + root). Moreover, the plant’s footprint in the vertical area was determined. The average offshoot growth of 1103 P American grapevine rootstock in the first and second applications was measured as 61.5 cm and 39.5 cm respectively, and it was 43.0 cm and 51.0 for C American grapevine rootstock. The average growth of 1103 P and 1616 C American grapevine in the control group was determined as 30.6 cm and 32.1 cm. The average growth of both American grapevine rootstocks used in the experiment was determined to be higher for the first and second applications than the controls.