Solar powering the increasing fleet of electrical vehicles (EV) demands more surface area than may be available for photovoltaic (PV) powered buildings. Parking lot solar canopies can provide the needed area to charge EVs, but are substantially costlier than roof- or ground-mounted PV systems. To provide a lower-cost PV parking lot canopy to supply EV charging beneath them, this study provides a full mechanical and economic analysis on three novel PV canopy systems: (1) exclusively wood, single parking spot spanning system, (2) wood and aluminum double parking spot spanning system, and (3) wood and aluminum cantilevered system for curbside parking. All systems can be scalable to any amount of EV parking spots. The complete designs and bill of materials (BOM) of the canopies are provided along with basic instructions and are released with an open source license that will enable anyone to fabricate them. The results found single-span systems have cost savings of 82%-85%, double-span systems save 43%-50%, and cantilevered systems save 31%-40%. In the first operation year, the PV canopies can provide 157% of energy needed to charge the least efficient EV currently on the market if it is driven the average driving distance in London ON, Canada.

In the present work report, the MgAl₂O₄and the Ag/MgAl₂O₄ samples were successfully synthesized by the modified hydrothermal and the isovolumetric impregnation methods, respectively. The structural properties of the prepared samples were systematically characterized by XRD, SEM, TEM, DRS, XPS and et al techniques. The photocatalytic degradation of methylene blue by the Ag/MgAl₂O₄ and MgAl₂O₄ samples was comparatively studied under UV lamp irradiation. The results revealed that the prepared Ag/MgAl₂O₄ (pH=6) samples were the most active among the samples in photocatalytic of methylene blue. Under UV lamp irradiation, the Ag/MgAl₂O₄ (pH=6) photodegradation of methylene blue reached to 89.6% within 120 min. And the Ag/MgAl₂O₄ (pH=6) complex photocatalysts displayed a high photochemical stability under repeated irradiation. Repeated irradiate the Ag/MgAl₂O₄ (pH=6) compound, which indicated it had a high photochemical stability.

Abstract: Development of the fast neutron radiography with higher penetration capability in Non-Destructive Testing (NDT) techniques is rapidly. The detection efficiency and the imaging spatial resolution are the main problem of the radiography detector for many fast neutron imaging systems. In this paper, a detector composed of pixelated EJ200 scintillator array，an 16 × 16 silicon-photomultipliers (SiPM) array, and a capacitive multiplexing network readout electronics is designed. Using Monte-Carlo simulations，the main parameters of the detector was optimization. Then the detector prototype was fabricated and tested at a 14 MeV D-T neutron source. The preliminary test results showed that the prototype has spatial resolution of 1.26 mm. Using pixelated scintillator structure，the conflict between spatial resolution and detect efficiency could improved. Moreover, SiPMs offer a flexibility for the expansion of application field of the imaging system due to their excellent photon detection performance, relatively low price and joint possibility for large area.

In the process of sewage coagulation treatment, quartz sand is often used as a heavy medium to accelerate the settling rate of flocs, but it will adversely affect the removal efficiency of pollutants. The factors that affect the coagulation effect and can be controlled manually include the quartz sand dosage, coagulant dosage, sewage pH, stirring time, settling time, etc, their reasonable setting is critical to. This paper was to study the optimal conditions of quartz sand enhanced coagulation(QSEC), first, single-factor tests were conducted to preliminarily explore the optimal range of influencing factors, and then response surface methodology（RSM）tests were performed to accurately determine the optimums of significant factors. The results showed that the addition of quartz sand can’t improve the water quality of coagulation treatment, but it can significantly accelerate the coagulation settlement process, the quartz sand dosage, the coagulant dosage and sewage pH all impacted significantly on its coagulation effect, and existed inflection points. A model that could guide QSEC was obtained by RSM tests. The model optimization and experimental validation showed that the optimal QSEC conditions for treating domestic sewage were as follows: the polyaluminum chloride(PAC) dosage, cationic polyacrylamide(CPAM) dosage, the sewage pH, quartz sand dosage, stirring time and settling time were 0.97 g·L-1, 2.25 mg·L-1, 7.22, 2 g·L-1, 5 minutes and 30 minutes, respectively, and the turbidity of treated sewage was reduced to 1.15 NTU.

Although solar photovoltaic (PV) system costs have declined, capital cost remains a barrier to widespread adoption. Do-it-yourself (DIY) system designs can decrease costs by about 50% by reducing labor costs, but if not attached to a building structure demand ground penetration for conventional footings. This is not technically and economically feasible at all sites. To overcome these challenges, this study details systems designed to eliminate drilling holes and pouring concrete. Two different designs for both fixed tilt and variable tilt PV racking are investigated to assess their structural integrity, constructability, and economic cost when fabricated with a ballast-supported foundation. The ballast-supported foundations are analyzed for eight such systems by proposing two separate ballast designs: one for single line of post systems, and one for double line of post systems built on a 4-kW basis. The results of the analysis found that both designs are slightly more expensive than typical in-ground concrete systems by 25%, but the overall DIY systems costs remain economically advantageous. Sensitivity analyses are conducted to show how modifications to the dimensions including clearances and distances between gabions influence the weight of the system and thus change the economic value of the design, so users can trade dimensional freedom for cost-savings, and vice versa. Overall, all the wood-based PV racking system designs provide users with cost-effective and easy DIY alternatives to conventional metal racking, and the novel ballast systems presented provide more versatility for PV systems installations.

Photovoltaic (PV) technologies are developing rapidly as a result of their ability to reduce energy consumption from conventional sources as well as the growth of global energy expenditures. Nevertheless, several impact categories during the PV panel life cycle occur and some principal sectors are affected. These impact categories are assessed by applying life cycle analysis (LCA) techniques through various software programs, databases and methods. Such analyses of energy technologies are crucial, as they can reveal the occurrence of hazardous emissions at distinct life cycle stages. In the present paper, a PV panel impact assessment through life cycle analysis is carried out. More precisely, a combination of PV technologies—monocrystalline, multicrystalline, copper indium gallium selenide (CIGS), amorphous, and ribbon—is studied. The impact categories of ozone depletion, human toxicity, particulate matter, ionising radiation, photochemical ozone formation, acidification, eutrophication, and ecotoxicity, as well as the sectors of human health, ecosystem quality, and environment, are assessed using the openLCA software, the ecoinvent database, the eco-indicator 99, IMPACT 2002+, ReCiPe, and TRACI methods.

This study focuses on the design, installation, and performance evaluation of a photovoltaic farm situated in Tulcea County, Romania, connected to a 20 kV distribution network. The farm, with a peak capacity of approximately 2800 kWp, benefits from Romania’s favorable climate conditions and supportive renewable energy policies. The analysis encompasses both the photovoltaic panel array and the electrical energy evacuation system. The substation at the park is equipped with technology that adheres to European standards and incorporates advanced features typical of modern electricity distribution networks. The assessment includes an evaluation of the park’s operational efficiency, with detailed calculations of the performance ratio and various power losses attributed to factors like temperature fluctuations, fouling, inverter efficiency, grid-related challenges, and availability issues. The farm contributes around 3620 MWh of electricity to the grid annually, demonstrating the effectiveness of photovoltaic installations in promoting sustainable energy solutions within regional energy networks.

Reasonable allocation of production plans and saving the overall electricity cost are crucial for large manufacturing conglomerates, which is an effective way for conglomerates to realize open-source and cost-saving. This paper develops an optimization model of off-site industrial production scheduling for enterprises in response to the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's electric power and the difficulty of promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and different electricity prices in different places to optimize the scheduling of industrial production in different places. The model is embedded with two sub-models of the electricity price prediction model and distributed photovoltaic kWh cost model to complete the model parameters, in which the electricity price prediction model utilizes the LSTM neural network. The integrated model is then solved by the particle swarm algorithm. To verify the effectiveness of the model in solving the problem of off-site production scheduling on the demand side of electricity, the research team researched two off-site pharmaceutical factories belonging to the same large pharmaceutical company. Finally, the research data were substituted into the model for solving, and it was concluded that the optimization model could significantly reduce the cost of electricity consumption of the enterprise by about 7.9 %.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

Conventional fertilization practices can lead to many ecological problems, such as nutrient imbalance, soil acidity, and reduced soil fertility in natural rubber plantations. To address these challenges, a field investigation was strategically carried out to substitute inorganic fertilizer with organic fertilizers consisted of six treatments, i.e., no fertilization (CK), inorganic fertilizer (NPK), 25 % replacement of inorganic through organic (25%M), 50 % replacement of inorganic through organic (50%M), 75 % replacement of inorganic through organic (75%M), and 100% organic fertilizer (100%M). The soil physicochemical properties (SOC, TN, AN, C:N, pH, NH4+-N, and NO3--N) and carbon and nitrogen converting enzymes (BG, NAG, and LAP) were all determined. The partial substitution of inorganic fertilizers with organic fertilizers (i.e., 75%M at surface soil layer) showed higher SOC (14.52 g.kg-1), TN (1.06 g.kg-1), AN (20.07 mg.kg-1), C:N (14.63), NH4+-N (10.63 mgkg-1), and NO3--N(11.06 mg.kg-1) than NPK and CK. Such increase in physicochemical properties in partial replacement of inorganic with organic fertilizers plots resulted from higher carbon and nitrogen enzymes activities (BG (143.17 nmol.g-1.h-1), NAG (153.96 nmol.g-1.h-1), and LAP (153.48 nmol.g-1.h-1)) compared to NPK and CK, and further the person correlation and RDA analysis confirmed a significant positive correlation between SOC, AN, and soil enzymes. This study presents a new strategy for assessing the impact of partially replacing inorganic fertilizers with organic fertilizers in rubber plantations, mainly by modifying the soil nutrient composition in tropical regions.

Halide perovskite materials gain enormous attention for their semiconducting properties, higher power conversion efficiency and potential applications in a wide range field of studies along with their two key limitations: stability and toxicity. In spite of great progress made on the halide perovskites and many promising research developments, overcoming these limitations is not realized yet. Therefore, coordination engineering of new framework for obtaining alternative new halide perovskite materials and fundamental understanding of the coordination chemistry and electronic interactions forming the structure of these newly engineered halide perovskite materials might be one way in order to overcome the issues related to both stability and toxicity. In this review, the current development of halide perovskite families, both lead halide perovskites and lead free halide perovskites followed by coordination engineering of the new frameworks to engineer new halide perovskite materials will be reviewed comprehensively. Moreover, all the concerns of the fundamental ideas of coordination chemistry and electronic interactions that are keys in forming the halide perovskite structures are discussed in detail and form the main aim of this review. Interestingly, we also discuss recent potential energy applications beyond photovoltaic and this review has completed with an essential and open question: ‘what could happen in the future of halide perovskites?’ in order to excite commercial enterprises and research institutions again as well as to get motivating new predictions on the future continuity of this field.

Integrated photovoltaic-fuel cell (IPVFC) systems have the potential to contribute to sustainable energy production for grid and off-grid applications. While there are studies focusing on fundamental science and designs for IPVFC systems, there are scarcely studies that have focused on the manufacturability of IPVFC systems, which is certainly the pathway for commercialisation of the systems. This study explores manufacturing strategies that can be considered for exploiting a family of eleven IPVFC systems. A survey and systems thinking were used to investigate the potential modularisation and supply chain management to achieve optimal lean and agile manufacturing strategy. Results show that the Photovoltaic-Thermal-Separate Converter/Inverter-Battery System received 25% of the responses. The optimal manufacturing strategy depends on the overall business strategy of the firm. Although 17% preference for System 1 is significant compared to four members of the family of IPVFC systems (Systems 2, 6, 8 and 9) that received only 2% of the responses, it indicates that there is a likelihood that the demand for System 1 will be among the top 42% of the total demand. Overall, this study provides new insights on how the family of IPVFC systems can contribute to realising greater access to clean energy, by extension contributing to the net-zero efforts using solar energy and solar hydrogen.

Background: Extra virgin olive oil is a fundamental component of the Mediterranean diet. It contains several molecules that sustain human well-being by modulating cellular metabolism and exerting antioxidant, anti-inflammatory, anti-ageing effects to protect normal tissues and can exert anti-angiogenic, and pro-apoptotic effects on cancer cells. Metabolites found in different parts of the olive tree, including leaves, also possess properties that might help in cancer prevention and promote wellness in aging. Olive mill wastewater (OMWW), a liquid residue produced during olive oil extraction, represents an environmental issue. However, it is enriched in phytochemicals with potential beneficial properties. Dietary supplements based on OMWW can be produced for nutritional supplementation with advantages to the ecology. Purpose: This work aims to measure hematochemical, anthropometric and metabolomic parameters in volunteers assuming an OMWW dietary supplement, OliphenoliaⓇ (OMWW-OL). Methods: The supplementation of OMWW-OL 25 mL twice daily for 30 days was tested on a pilot cohort of volunteers with characteristics close to metabolic syndrome. Hematochemical, anthropometric, and metabolomic parameters were analyzed before the intervention, at 30 days and 30 days after stopping consumption. Results: 29 volunteers were enrolled and 23 completed the study. The participants’ parameters at baseline were measured, and then twice daily at 30 days of treatment and 30 days after assumption discontinuation. Although treatment was with an olive derivative, weight and body mass index instead of increasing slightly decreased, particularly in women. Also, hydration increased, especially in women, while blood pressure, glycemia and insulin decreased. Cholesterol, low-density and high-density lipoproteins and triglycerides were stable while vitamin D levels, alongside calcium, sensibly increased. Albumin also increased and parameters related to sarcopenia displayed promising, although not statistically significant, trends toward positive effects. All the values were in support of an equilibrium with no damaging effects. By mass spectrometry analysis, we also found favorable changes in the vitamin D/histamine and homocysteine/methionine ratios, an increase in a new metabolite of unknown formula, and vitamin D/unknown metabolite ratio. Conclusions: Supplementation of OMWW-OL has no detrimental effects and, although with limited potency of a pilot study, might imply the beneficial modulation of several biological parameters, being potentially valuable for people at risk of metabolic syndrome. Some of these parameters could also be relevant as anti-ageing and in cancer prevention.

Agrivoltaic agrotunnels are currently designed for high density grow walls that are not amenable to bush berries or root crops. Commercial grow bins provide deeper substrates for produce with more root systems but have high costs per unit growing area. To overcome the economic limitations of grow bins, this study applies the distributed manufacturing open-source design paradigm to develop four designs for low-cost open source structures. The designs target root vegetables and bush fruit specifically to be adopted by remote communities with limited or no outdoor growing environment to offset the market price for imported fresh produce. The indoor growing designs provide the necessary structure for supporting grow light and grow bins and enabled the transplanted berry plants to flower and produced fruits. They provide a comparable amount (110L) or more of grow volume from 106 to 192 L. The water reservoir volume for the commercial system (62 L) and grow area (0.5 m³) is surpassed by all new designs that range from 64 to 192 L and 0.51 to 0.76 m³, respectively. These superior properties are possible with material costs for all four designs that save more than 90% of the economic cost of the commercial systems.

Macrophages as a source and target of GDF-15

The atomic structures of Zn and Na borophosphate glasses were studied by X-ray and neutron diffraction. Peaks assigned to the B−O, P−O, and O−O distances confirm that only BO4 units co-exist with the PO4 tetrahedra. The Zn−O and Na−O coordination numbers are found to be a little larger than four. The narrowest peaks of the Zn−O first-neighbor distances exist for the glasses along a line connecting the Zn(PO3)2 and BPO4 compositions (50 mol% P2O5) which is explained by networks of ZnO4, BO4, and PO4 tetrahedra with twofold coordinated oxygens. Calculated amounts of the available oxygen support this interpretation. Broadened peaks occur for glasses with lower P2O5 contents, consistent with the presence of threefold coordinated oxygens. The two distinct P−O peak components of the Zn and Na borophosphate glasses differ in their relative abundances which is interpreted by Na+ cations that coordinate oxygens in some P−O−B bridges, something not seen for the Zn2+ ions.

Abstract In order to solve the problem that it is difficult to obtain the accurate trigger signal moment when using the time difference of UAV flight acoustic signals collected by acoustic sensors arranged in advance to locate the position of UAVs when they cannot be tracked by radar and are difficult to be observed by the human eye, an acoustic source localisation method with improved empirical modal decomposition (REMD) under an adaptive frequency window is proposed. Firstly, the collected UAV flight signals are smoothed and filtered, then the robust empirical modal decomposition (REMD) is used for IMF modal decomposition and spectral analysis of the collected signals, and a panning frequency window with variable bandwidth is introduced for corresponding frequency locking and extracting the IMFs; the GWO optimisation is used and the sliding metrics are set to determine the position of the panning frequency window automatically; finally, the extracted Finally, the extracted IMF components are reconstructed according to the criterion, and the trigger signal moments in the reconstructed IMF components are resolved and recorded, and the algorithm is used to calculate the difference between the reception moments of different sensors; for the traditional sound source localisation algorithms with a small detection range, which are prone to fall into the no-solution or false-solution, i.e., unable to achieve the localisation, a weighted least-squares-based Chan-Taylor algorithm is proposed for the localisation computation, and a weighted least-squares algorithm is proposed for the localisation computation, through the Inputting the sensor delay parameter and solving the linear equation system to get the target position information; finally, this paper verifies the robustness and performance of the design method with simulated and actual signals. The results show that the maximum positioning error is no more than 5% in an area with a side length of 15m in the measurement area. With the improved accuracy of time delay estimation, the positioning simulation results meet the positioning requirements even though the positioning error is further expanded when the measurement area is further expanded.

Strong-aroma Baijiu is a traditional Chinese spirit distilled from grains that undergo solid-state fermentation. At the end of each fermentation cycle, a significant quantity of Huangshui accumulates at the bottom of the fermentation pit, constituting one of the primary by-products in the brewing process of strong-flavor liquor. In this report, the chemical component analysis of Huangshui obtained from a strong-flavor liquor factory revealed a diverse array of organic acids, alcohols, esters, starch, reducing sugars, amino acids, and other compounds present in Huangshui. Additionally, two specialized solid-state fermentation models were developed to investigate the formation process of Huangshui. Our findings demonstrate a positive correlation between the yield of Huangshui and the initial moisture content of fermented grains. It is concluded that Huangshui is the percolate produced during the solid-state brewing process of strong-flavor liquor, with its water content originating from the initial moisture of fermented grains.

Photovoltaic (PV) systems, which are renewable energy sources, are increasingly being utilized in distributed generation. To maintain a stable energy balance, energy storage systems such as batteries (BAT) play a vital role. Electric vehicles (EVs) offer a promising solution with rechargeable battery systems for operation. The BATs must maintain their state of charge within design boundaries, despite intermittent PV and load power fluctuations, and advanced power control and management techniques are essential for their effective operation. The article evaluates an intelligent controller that uses a Sliding Mode Control adaptive deep learning algorithm Convolutional Neural Networks (SMC-CNN) and a unique Strategy for managing supervisory power. (SPMS) for photovoltaic systems with battery energy storage for better regulation of DC bus voltage. SMC-CNN offers exceptional resilience and seamless functionality, minimizing fluctuations in DC bus voltage in the control strategy design requirements. The primary goals are maintaining a consistent power supply and ensuring continuous service by preventing system components from exceeding capacity. This study aims to enhance the control of DC bus voltage in the PV and battery system, with the primary significance focusing on the following aspects. The advanced SPMS has been created, incorporating control system constraints to enhance SOC balancing speed and reduce fluctuations in DC bus voltage. Power flow management involves optimizing energy flow between the PV system, battery system, and load while minimizing battery capacity requirements. The proposed SMC-CNN and SPMS are demonstrated through real-time simulation using Matlab/Simulink, as demonstrated in comprehensive case studies.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

With the global increase of photovoltaic (PV) modules deployment in recent years, the need to explore and realize their reported failure mechanisms has become crucial. Despite PV modules being considered reliable devices, failures and extreme degradations often occur. Some degradations and failures can be minor and cause no critical harm if within the expected range. Others, may start mildly and then deteriorate faster to become catastrophic, especially in harsh environments. This paper conducts a state-of-the-art literature review to scan PV failures, types, and their root cause based on PV’s constructed components (from protective glass to junction-box). It outlines the hazardous consequences beyond PV module failures, describing what harm they can bring to the PV system. As we delve into the literature, it becomes clear that every component is vulnerable to certain types of failures; some can deteriorate within themselves, and others infect further PV components resulting in emerging more severe failures. In the end, the review briefly summarises PV failure detection techniques, emphasising electrical characterization techniques, and disclosing the need to engage more electrical parameters. Most importantly, this review can prepare the stage for the PV research community to identify the most prevalent degradation processes. This, in turn, encourages researchers to investigate them throughout modelling and experimental studies to forecast them at the early onset in order to protect the PV systems from hazardous malfunctions.

In this paper, we consider a fourth-order suspension bridge equation with nonlinear damping term |u_t|^m-2u_t and source term |u|^p-2u. We give necessary and sufficient condition for global existence and energy decay results without considering the relation between m and p. Moreover, when p>m, we give sufficient condition for finite time blow-up of solutions. The lower bound of the blow-up time T_max is also established. It worth to mention that our obtained results extend the recent results of Wang (J. Math. Anal. Appl., 2014) to the nonlinear damping case.

Distributed/semi-distributed models are considered to be sensitive to the spatial resolution of the data input. In this paper, we take a small catchment in high urbanized Yangtze River Delta, Qinhuai catchment as study area, to analyze the impact of spatial resolution of precipitation and the potential evapotranspiration (PET) on the long-term runoff and flood runoff process. The data source includes the TRMM precipitation data, FEWS download PET data, and the interpolated metrological station data. GIS/RS technique was used to collect and pre-process the geographical, precipitation and PET series, which were then served as the input of CREST (Coupled Routing and Excess Storage) model to simulate the runoff process. The results clearly showed that, the CREST model is applicable to the Qinhuai catchment; the spatial resolution of precipitation had strong influence on the modelled runoff results and the metrological precipitation data cannot be substituted by the TRMM data in small catchment; the CREST model was not sensitive to the spatial resolution of the PET data, while the estimation fourmula of the PET data was correlated with the model quality. This paper focused on the small urbanized catchment, suggesting the influential explanatory variables for the model performance, and providing reliable reference for the study in similar area.

A pivotal strategy in decarbonizing the transport sector is by transitioning from internal combustion engine vehicles (ICEVs) to electric vehicles (EVs), especially if they are charged with renewable energy. To provide an incentive to the common populace to switch to EVs, cities should set up - or enable or even encourage the private sector to do so - electric vehicle charging stations (EVCS) at multiple and suitably accessible locations. This paper aims to present a digitaltwin-enabled methodology study for selecting the most suitable possible locations to establish EVCS with consideration of the low voltage (LV) network operation in terms of power losses, active and reactive power in EV charging demand and the effect of the EVCS on the transformers, based on examples in Newcastle upon Tyne (England, UK). It also evaluates the most suitable type of charger that could be installed at these locations by studying the estimated traffic, cost and impact of the EVCS on the power grid, both at peak and off hours. This paper demonstrates how digitaltwin technologies, such as the web-based tool AutoDesign by Northern Powergrid and EA Technology and open source Pandapower can be used for identifying the most viable and cost-effective locations to connect EVCSs to a Distribution Network Operators (DNO)’s LV network. The results of the analysis indicate that with the installation of the most suitable type of EVCS in a particular location, the local power grid would not be significantly affected at any hour of the day.

Additives for anaerobic digestion (AD) can play a significant role in optimising the process by increasing biogas production, stabilising the system and improving digestate quality. The role of additives largely boils down to: (i) enhancing direct interspecies electron transfer (DIET) between microbial communities, resulting in improved syntrophic interactions and methane production rates (e.g. biochar, magnetite and carbon nanotubes), (ii) adsorption of toxic substances that may inhibit microbial activity (e.g. activated carbon, zeolites), (iii) improving microbial activity and increasing process stability (e.g. cobalt, nickel, iron, selenium), (iv) maintaining optimal pH levels for microbial activity (e.g. magnesium oxide), (v) reducing inhibition (the aforementioned adsorbents and conductive substances), (vi) accelerating the decomposition of complex organic materials into simpler compounds that are more easily digested by microorganisms, thereby increasing the rate of hydrolysis (enzymes, including cellulases, proteases and lipases). Through the aforementioned action, additives can significantly affect AD performance. The function of these materials varies, from enhancing microbial activity to maintaining optimal conditions and protecting the system from inhibitors. The choice of additives should be carefully tailored to the specific needs and conditions of the digester to maximise benefits and ensure sustainability. In light of these considerations, this paper characterizes the most commonly used additives and their combinations based on a comprehensive review of recent scientific publications, including a report on the results of conducted studies. The publication features chapters that describe: carbon-based conductive materials, metal oxide nanomaterials, trace metal and biological additives, including enzymes and microorganisms. It concludes with a chapter summarising reports on various additives and discussing their indications for functional systems with determined properties. A notable advantage of this work is the updated literature data, clear summaries, and a substantive description of the performance of the additives discussed.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

Primary Ciliary Dyskinesia (PCD) is a rare genetic disorder characterized by alterations in motile cilia func-tion. The diagnosis of PCD is challenging due to the lack of standardized methods in clinical practice. High-speed video microscopy analysis (HSVA) directly evaluates ciliary beat frequency (CBF) in PCD. Recently, open-source ciliary analysis software applications have shown promise in measuring CBF accurately. How-ever, there is limited knowledge about the performance of different software applications, creating a gap in understanding their comparative effectiveness in measuring CBF in PCD. We compared two open-source software applications, CiliarMove and Cilialyzer, against the manual count method. We used videos rec-orded at high-speed of nasal ciliary brush samples from PCD patients and healthy controls. All three meth-ods showed lower median CBF values in PCD patients than healthy controls. CiliarMove and Cilialyzer identified lower CBF in PCD patients, similar to the manual count. Cilialyzer, CiliarMove and manual count demonstrated statistical significance (p-value < 0.0001) in the difference of median CBF values be-tween PCD and healthy controls. These findings support the utility of open-source software-based analysis tools. Further studies are needed to validate these findings with other genetic variants and identify the op-timal software for accurate CBF measurement in PCD.

A photovoltaic-thermal (PVT) collector is a solar-based micro-cogeneration system which generates simultaneously heat and power for buildings. The novelty of this paper is to conduct energy and exergy analysis on PVT collector performance under two different European climate conditions. The performance of the PVT collector is compared to a PV panel. Finally, the PVT design is optimized in terms of thermal and electrical exergy efficiencies. The optimized PVT designs are compared to the PV panel performance as well. The main focus is to find out if the PVT is still competitive with the PV panel electrical output, after maximizing its thermal exergy efficiency. The PVT collector is modelled into Matlab/Simulink to evaluate its performance under varying weather conditions. The PV panel is modelled with the CARNOT toolbox library. The optimization is conducted using Matlab gamultiobj-function based on Non-Dominated Sorting Genetic Algorithm-II (NSGA-II). The results indicated 7.7% higher annual energy production in Strasbourg. However, the exergy analysis revealed a better quality of thermal energy in Tampere with 72.9% higher thermal exergy production. The electrical output of the PVT is higher than from the PV during the summer months. The thermal exergy- driven PVT design is still competitive compared to the PV panel electrical output.

The paper presents the author’ original modification of the residual method in order to construct an efficient tool for assessing the condition of photovoltaic cells, in particular – panels made of amorphous cells which are characterized by significant random operation parameter changes. The solution constructed has been verified through experiments, which show the usefulness of the proposed methodology as it allows to minimize the risk of obtaining false diagnostic information in the process of assessing the condition of photovoltaic panels.

Despite the recent availability of immune checkpoint inhibitors, not all patients affected by Non-Small Cell Lung Cancer (NSCLC) benefit from immunotherapy. The reason for this variability relies to a variety of factors which may allow the identification of novel biomarkers. Presently, a variety of biomarkers are under investigation, including the PD1/PDL1 axis, the tumor mutational burden, and the Microbiota. This latter is made by all bacteria and other microorganisms hosted in our body. The gut microbiota is the most represented and has been involved in different physiological and pathological events, including cancer. In this light, it appears that all conditions modifying gut microbiota can influence cancer, its treatment, and its treatment-related toxicities. The aim of this review is to analyze all conditions influencing the gut microbiota and, therefore, affecting response to immunotherapy, iRAEs and their management in NSCLC patients. The investigation of the landscape of these biological events can allow novel insights for optimal management of NSCLC immunotherapy.

Hypophthalmichthys nobilis are widely distributed in the Yangtze River basin and its related lakes. They are an important economic fish species and are a famous cultured species known as the "Four Famous Domestic Fishes" in China. Currently, with the fishing ban in the Yangtze River basin, fishing for H. nobilis in natural water bodies of the Yangtze River basin has been completely prohibited. In order to identify the sources of H. nobilis appearing in the market, further control and accountability, it is necessary to trace the sources of H. nobilis in the Yangtze River basin and its related water bodies. Therefore, this study identified and traced different sources of H. nobilis through muscle element fingerprint analysis (EFA). The results show that H. nobilis from different stations have characteristic element compositions. The characteristic element of H. nobilis from Wuhan (WH) is Pb, which is significantly higher than that in other stations; the characteristic element from Anqing (AQ) is Hg, which is significantly higher than that in other stations; and the characteristic element from Taihu (TH) is Al, which is significantly higher than that in other water areas. Multivariate analysis selected different spatial distribution patterns of 4 discriminant elements ratios (Pb/Ca, Cr/Ca, Na/Ca, Al/Ca) in the muscle of H. nobilis in the Yangtze River basin and its related lakes. The study suggests that the screened discriminative elements can be used to visually distinguish different sources of H. nobilis, and to quickly trace and verify the origin of newly emerging samples. Therefore, the use of selected discriminant element fingerprint features to trace the origin of new samples has been proven to be feasible. By further discriminating and verifying the muscle element fingerprints of new samples, the discrimination rate is high. Therefore, Multivariate analysis for muscle element fingerprint can be used for origin traceability of samples of unknown origin in market supervision.

The complexity of software is increasing day by day due to the increase in the size of the projects being developed. For better planning and management of large software projects, estimation of software quality is important. During the development processes, complexity metrics are used for the indication of the attributes/characteristics of the quality software. There are many studies about the effect of the complexity of the software on the cost and quality. In this study, we discussed the effects of software complexity on the quality attributes of the software for open source and closed source software. Though, the quality metrics for open and closed source software are not distinct from each other. In this paper, we comparatively analyzed the impact of complexity metrics on open source and private software. We also presented various models for the management of the project complexity such as William’s Model, Stacey’s Agreement and Certainty matrix, Kahane’s Approach and UCP Model. Quality metrics here refer to the standards for the measurement of the quality of software which contains certain attributes or characteristics of the software that are related to the quality of the software. Certain quality attributes addressed in this study are Usability, Reliability, Security, Portability, Maintainability, Efficiency, Cost, Standards and Availability, etc. Both Open source and Closed source software are evaluated on the basis of these quality attributes. This study also recommended future approaches to manage the quality of project Open source and Closed source software and specify which one of them is mostly used in the industry.

The growing interest in the use of energy storage systems to improve the performance of tramways has prompted the development of control techniques and optimal storage devices, displacement, and sizing to obtain the maximum profit and reduce the total installation cost. Recently, the rapid diffusion of renewable energy generation from photovoltaic panels has also created a large interest in coupling renewable energy and storage units. This study analyzed the integration of a photovoltaic power plant, supercapacitor energy storage system, and railway power system. Random optimization was used to verify the feasibility of this integration in a real tramway electric system operating in the city of Naples, and the benefits and total cost of this integration were evaluated.

The research that we are referring to examines the morphological, structural, and optical characteristics of kesterite (Cu1-xAgx)2ZnSnS4 (CAZTS) thin films, which are produced using a process known as thermal evaporation (TE). The study's main goal was to determine how different Ag contents affect the characteristics of CAZTS systems. X-ray diffraction (XRD) and Raman Spectroscopy: were used to confirm the crystal structure of the CAZTS thin films. Using a mathematical model of spectroscopic ellipsometry, the refractive index (n) represented the part of the complex refractive index, the extinction coefficient (k) portrayed the imaginary one, and also the energy band gap of the fabricated films were all calculated. The energy band gap of the thin films was also calculated. This is a crucial parameter for solar cell applications, as it determines the wavelength of light that the material can absorb. The energy band gap was found to decrease from 1.74 eV to 1.55 eV with increasing Ag content. The ITO/n-CdS/p-CAZTS/Mo heterojunction was well constructed, and the primary photovoltaic characteristics of the n-CdS/p-CAZTS junctions were examined for use in solar cells. Different Ag contents of the CAZTS layers were used to determine the dark and illumination (current-voltage) characteristics of the heterojunctions. The study's findings collectively point to CAZTS thin layers as potential absorber materials for solar cell applications.

All solar thermal systems, due to their thermal nature, can be hybridised or operated with both fossil fuel and solar energy. By enhancing availability and dispatch ability, hybridization has the potential to boost the value of concentrating solar thermal technology. Hybrid photovoltaic thermal systems (PV/T) offer a solution to improve on the limited capacity growth seen with standard solar panels. The analysis focuses on the creation of alternative structural and design so-lutions that may be used to boost lacking efficiency that was previously hampered by limited spectrum absorption of sun light. As a result, the spectrum is separated into two spectrum ranges, one that directly matches the bandgap of PV materials and the other that is absorbed for thermal absorption outputs. Most two channel systems are used to capture or reflect sunlight, with the layer specifically located right above the PV cell. Another layer of nanofluid is employed to evacuate heat from the PV cell, acting as the second channel, to specifically eliminate overheating difficulties. To address concerns that have arisen as a result of years of observation, the most recent study involves nano-particle-based fluids employed in PV/T, which uses a cooling medium to provide an alternate heat transfer option. Aside from nanofluids, there are phase change materials, channel alterations that result in a higher flow rate and hence improve overall performance.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

The aim of this research work is to study the influence of temperature, solar irradiation and wind dust on the production of solar energy. In addition, it aims to study the assessment of water quality, in particular groundwater used for cooling and cleaning photovoltaic panels (quality analysis). it's an important source, stable and sustainable can be used entirely for cooling and cleaning PV modules from the sales dust, in order to improve their performance. To date, all research studies carried out in this context of cooling and cleaning using water have not taken account of the nature of this water. We have taken a sample of water from a well in a rural area in the Darra Tafilalet region of Morocco. This region has an arid and semi-arid climate, with very high temperatures and dust-laden winds, particularly in summer. These meteorological characteristics influence the efficiency of cells, particularly photovoltaic (PV) panels, reducing their performance. Next, the water sample was analysed in the laboratory. The results obtained show that the groundwater in this area is very sensitive to cooling and cleaning photovoltaic panels. Moreover, these results indicate that the temperature, solar irradiation and wind-blown dust have a significant influence on energy production.

Microgrids offer flexibility in power generation in a way of using multiple renewable energy sources. In the past few years, microgrids become a very active research area in terms of design and control strategies. Most of the microgrids use DC/DC converters to connect renewable energy sources to the load. In this paper, the simulation model of a DC microgrid with three different energy sources (Lithium-ion battery (LIB), photovoltaic (PV) array, and fuel cell) and external variant power load is built with MATLAB/Simulink and the simulative results show that the stability of DC microgrid can be guaranteed by the proposed maximum power point controller MPPT. The three energy sources are connected to the load through DC/DC converters, one for each. This type of topology ensures protection for each energy source as well as optimum stability at the load.

This work focuses on identifying the most effective machine learning techniques and supervised learning models to precisely estimate power output from Photovoltaic (PV) plants. The performance of various regression models is analyzed by harnessing experimental data, including Random Forest, Support Vector Regression (SVR), Multi-layer Perceptron (MLP), Linear Regressor (LR), Gradient Boosting, and k-Nearest Neighbors (KNN). The methodology applied starts with meticulous data preprocessing steps aimed at ensuring dataset integrity. Following the preprocessing phase, which entails eliminating missing values and outliers using Isolation Feature selection based on a correlation threshold, is performed to identify relevant parameters for accurate prediction in PV systems. Subsequently, Isolation Forest is employed for outlier detection, followed by model training and evaluation using key performance metrics such as Root Mean Squared Error (RMSE), Normalized Root Mean Squared Error (NRMSE), Mean Absolute Error (MAE), and R-squared (R2). Among the array of models evaluated, Random Forest emerges as the top performer, highlighting promising results with an RMSE of 19.413, NRMSE of 0.048% and an R2 score of 0.968. Furthermore, the best-performing model is integrated into a MATLAB application for real-time predictions, thereby enhancing usability and accessibility for a wide range of applications in renewable energy.

This work focuses on short-term forecasting of PV output power. The multilayer perception (MLP), convolutional neural networks (CNN), and k-nearest neighbour (kNN) neural networks have been used singly or in a hybrid (with other algorithms) to forecast solar PV power or global solar irradiance with good success. Their performances in forecasting PV power have been compared with other algorithms but not with themselves. The study aims to compare performance of a number of neural network algorithms in solar PV energy yield forecasting under different weather conditions. The performance of MLPNN, CNN and kNN are being compared using solar PV (hourly) energy yield data for Grahamstown, Eastern Cape, South Africa. The choice of location is part of the study parameters to provide insight into renewable energy power integration in specific areas in south Africa that may be prone to extreme weather conditions. The kNN algorithm was found to have RMSE value of 4.95% and MAE value of 2.74% at its worst performance, and RMSE value of 1.49% and MAE value of 0.85% at its best performance. It outperformed the others by a good margin and kNN could serve as a fast, easy, and accurate tool to forecast solar PV output power.

The evolution of photovoltaic cells is intrinsically linked to advancements in the materials from which they are fabricated. This review paper provides an in-depth analysis of the latest developments in silicon-based, organic, and perovskite solar cells, which are at the forefront of photovoltaic research. We scrutinize the unique characteristics, advantages, and limitations of each material class, emphasizing their contributions to efficiency, stability, and commercial viability. Silicon-based cells are explored for their enduring relevance and recent innovations in crystalline structures. Organic photovoltaic cells are examined for their flexibility and potential for low-cost production, while perovskites are highlighted for their remarkable efficiency gains and ease of fabrication. The paper also addresses the challenges of material stability, scalability, and environmental impact, offering a balanced perspective on the current state and future potential of these material technologies.

In the last two decades, the continuous ever growing demand for energy has determined a significant development in the production of photovoltaic (PV) modules. Anyway, a critical and very important issue in the module design process is the adoption of suitable encapsulant materials and technologies for cell embedding. Therefore, adopted encapsulants have a significant impact on modules efficiency, stability and reliability, and to ensure the unchanged performance of PV modules in time, the encapsulant materials must be selected properly. The selection of encapsulant materials must maintain a good balance between the encapsulant performance in time and costs, related to materials production and technologies for cells embedding. However, the encapsulants must ensure excellent isolation of active photovoltaic elements by the environment, preserving accurately the PV cells against humidity, oxygen and accidental causes that may compromise the PV modules function. This review provides an overview of different encapsulant materials, their main advantages and disadvantages in adoption for PV production, and also in relation to used encapsulant technologies for cell embedding, additives and the interaction of these materials with other PV components.

This work presents a control scheme to control the grid-connected single-phase photovoltaic (PV) system. The considered system has four 250W solar panels, a non-inverting buck-boost DC-DC converter, and DC-AC inverter with LCL filter. The control system aims to track and operate at the maximum power point (MPP) of PV panels, regulate the voltage of DC link, and supply the grid with a unity power factor. To well achieve these goals, the proposed control system consists of three parts, that are MPP tracking controller module with a fuzzy-based modified incremental conductance (INC) algorithm, a DC-link voltage regulator with a hybrid fuzzy proportional-integral (PI) controller, and a Current Controller module using the linear quadratic regulator (LQR) for grid-connected power. Based on fuzzy control and LQR, this work introduces a full control solution for grid-connected single-phase PV systems. The key novelty of this research is to analyze and prove that the newly proposed method is more successful in numerous aspects by comparing and evaluating the previous and present control methods. The designed control system settles quickly, which is critical for output stability. In addition, as compared to backstepping approach used in our past study, the LQR technique is more resistant to sudden changes and disturbances. Furthermore, backstepping method produces the larger overshoot, which has a detrimental impact on efficiency. Simulation findings under various weather conditions were compared to theoretical ones to indicate that the system can deal with variations in weather parameters.

The aim of this work is to introduce new ways to model the I-V characteristic of a PV cell or PV module using straight lines and Bézier curves. This is a complete novel approach, Bézier curves being previously used mainly for computer graphics. The I-V characteristic is divided in three sections, modeled with lines and a quadratic Bézier curve in the first case and with three cubic Bézier curves in the second case. The result proves to be accurate and relies on the fundamental points usually present in the PV cell datasheets: Voc (the open circuit voltage), Isc (the short circuit current), Vmp (the maximum power corresponding voltage) and Imp (the maximum power corresponding current) and the parasitic resistances Rsh0 (shunt resistance at Isc) and Rs0 (series resistance at Voc). The proposed algorithm completely defines all the implied control points and the error is analyzed. The temperature and irradiance influence is also analyzed. The model is also compared using the least squares fitting method. The final validation shows how to use Bézier cubic curves to accurately represent the I-V curves of an extensive range of PV cells and arrays.

The escalation of mining activities in the karst regions of Guizhou Province has heightened the occurrence of water-inrush incidents in deep coal mines. This study focused on water-inrush phenomena within the Xinhua mining area of Jinsha County, Guizhou Province, aiming to investigate the sources of these incidents. The findings indicated that the overlying limestone of the Changxing Formation in the coal seam served as a vulnerable aquifer under certain conditions, leading to water inrushes. The analysis of the spatiotemporal distribution patterns of water-inrush incidents at the working face indicated that previous mining operations damaged the shallow Changxing Formation limestone, resulting in the accumulation of goaf water and the formation of numerous mining-induced fractures. These fractures served as rapid conduits for water inrushes from both atmospheric precipitation and underground sources at the deep working face. The examination of surface water and mine water quality demonstrated that both exhibited similar characteristics, predominantly featuring bicarbonate, sulfate, and sodium compositions. Investigation into the relationship between mine water inflow and atmospheric precipitation established that atmospheric precipitation influenced the mine water supply cycle, with a replenishment period of ~10 months during the operational phase of the Jinyuan Coal Mine and about one month post-closure. The fractures induced by mining activities within the Changxing Formation limestone facilitated water flow, with atmospheric precipitation serving as the primary water source for the mine. This study offered a valuable scientific foundation for addressing water-related damage resulting from atmospheric precipitation in mines susceptible to water inrushes under analogous hydrogeological conditions.

The Digital electronics collaborative enhanced learning (DECEL) project has recently developed an international collaborative education course. Its main objective is to enhance the digital electronics skills of international students by working on a complex, multidisciplinary applied problem using a mixed digital architecture. We have developed a logic level synthesis and dedicated software layers on the Red Pitaya FPGA platform. The diversity of digital concepts to be implemented, from hardware description language (HDL) to high-level languages such as Python or Matlab, forced the students to work together and rapidly improve their skills. Their motivation was fueled by the curiosity of controlling an ultrasound probe to obtain ultrasound signatures. This particular physics, little known to the students, was an additional source of curiosity. The goal of forming an image in a liquid medium was an additional motivating factor for them. The students reported that they learned a lot from the experiment. Thus, the technical parts and pedagogical results are documented in this work for reproducibility.

Nowadays Air-Source Heat Pumps (ASHP) in combination with a Photovoltaic (PV) installation are a very promising option for a necessary and urgent energy transformation in European Union (EU). It is extremely important to develop solutions that will help maximize the use of energy generated from renewable energy sources (RES). Such issues include the problem of insufficient use of generated electricity in PV on-grid microinstallations in residential buildings. This paper's aim is to analyze the results of one-year-round operation of a PV array grid-connected hybrid installation with ASHP for domestic hot water (DHW) preparation in a residential building in Cracow, Poland in the context of increasing self-consumption (SC) of PV energy. Models of systems are built and simulated in Transient System Simulation Tool 18 (TRNSYS) software. Simulations were carried out for different scenarios involving different building electricity consumption profiles, PV system capacity and specified runtime management of ASHP. The novelty of this study lies in the evaluation of the impact of a certain range of conditions on the energy performance of the system, in particular on SC. The results showed that the use of ASHP, with specified runtime management, results in an increase in monthly SC values from 7 to 18%, and annual SC values up to 13%. Also determining the appropriate size of the used PV system depending on whether it is present ASHP in the installation is crucial to increase the value of the SC parameter. Overall, this study provides valuable insights into the potential benefits of PV panels and ASHP operating together, in particular on SC values.

Photovoltaic (PV) generation is potentially uncertain. Probabilistic PV generation forecasting methods have been proposed with prediction intervals (PIs). However, several studies have dealt with geographically distributed PVs in a certain area. In this study, a two-step probabilistic forecast scheme is proposed for geographically distributed PV generation forecasting. Each step of the proposed scheme adopts ensemble forecasting based on three different machine-learning methods. In this case study, the proposed scheme was compared with conventional non-multistep forecasting. The proposed scheme improved the reliability of the PIs and deterministic PV forecasting results through 30 days of continuous operation with real data in Japan.

As an active device, air source heat pumps (ASHP) are widely used for heating and cooling in buildings. However, in cold regions, their efficiency decreases, and frost formation becomes a significant issue during winter. This paper proposes a new scheme that couples air source heat pumps with passive heating. By using software simulations and mathematical models, the new scheme is compared to traditional ASHP systems to analyze its heating performance in rural homes during winter in China’s cold regions. According to the simulation and calculation analysis, on the coldest day of winter, the coupling scheme can provide approximately 99.41kWh of heat to the interior, surpassing the 86.67kWh required to maintain an indoor temperature of 20℃. The system’s power consumption is 36.96 kWh, which is 66.88% lower than that of traditional heat pump heating. The study shows that a coupled system of air source heat pumps and passive heating has better heating performance in cold regions. By incorporating phase change materials and heat storage media to address the shortage of solar energy at night, the system can meet the heating needs throughout the entire day.

Flexible polymer-based dye-sensitized solar cells (DSSCs) offer promising potential for lightweight, cost-effective and versatile photovoltaic applications. However, the critical challenge in their widespread applications is the weak thermal stability of the majority of polymeric substrates, which can only withstand a maximum temperature processing of 150°C. In this study, we propose a facile and low-cost strategy to develop at low temperature DSSC flexible photoanode based on a polymeric matrix. Highly porous nanocomposites fibrous mats composed of polyethylene terephthalate (PET) and titanium dioxide (TiO2) nanobars were prepared through electrospinning process using different configurations (uniaxial electrospinning, coaxial electrospinning, and electrospray-assisted electrospinning). These techniques enabled precise control of the microstructure and the positioning of TiO2 within the composite nanofibers. Therefore, the as-produced photoanodes were loaded with N719 dye and tested in DSSC prototype using iodide-triiodide electrolyte and platinum (Pt) coated counter electrode. The results show that incorporating TiO2 on the fiber surface through the electrospray-assisted electrospinning enhanced the performance of the nanofiber composite, leading to improved dye loading capacity, electron transfer efficiency and photovoltaic performance.

The Software-Defined Networking concept plays an important role in network management. The central controller, which is the main element of SDN, allows to provide traffic engineering and security solutions in single and multiple-layer networks based on optical transmission. In this work, we compare selected open-source implementations of SDN controllers. Throughput and latency measurements were analyzed using the CBench program. The simulation of a link failure and a controller failure were conducted using the API provided by the Mininet network simulator. For detecting security vulnerabilities, a dedicated program, called sdnpwn, was used. The work provides an overview of the selected controllers, indicating their strengths and weaknesses. Moreover, some implemention suggestions and recommendations are presented.

Solid waste management is a global issue that affects every individual living in the world directly or indirectly. Failing to manage the waste properly will cause harm on public health, our natural environment, and even our happiness and prosperity. When asked about the reason behind the failure of third time plastic ban in Bhutan, one of the Bhutanese said it’s because of the lack of cooperation from public to support the move of government. Clean Bhutan, a non-governmental organization (NGO) that aims Zero Waste Bhutan by 2030, has collected around 5,900 metric tons of waste from December 2014 to February 2018. This project will create some awareness regarding the management of waste at individual level when people come in contact with the family of the researcher. It also talks abot how waste management and biodiversity conservation can go side by side.

In this paper, a fuzzy logic-based energy management system and multi-port quasi-z-source converter are proposed that utilizes hybrid renewable energy sources. The system ensures that each energy source module can be used individually by employing fuzzy logic to define power modes. This approach also helps prevent switching losses resulting from extra switching of the source modules. Also, the proposed energy management does not have a mathematical model, so applicability is simple and it is suitable for different multiple input topologies. The Mamdani fuzzy inference system can be designed to capture the nonlinear behavior of the system because of the linguistic rules. Moreover, by adopting the quasi-z-source network to the end of the multi-port converter, the switching losses of the multi-port modules have been significantly reduced. The simulation results are obtained using MATLAB Simulink, and the experimental results are obtained by connecting the circuit to MATLAB Simulink via an Arduino Due.

This paper offers a theoretical and experimental examination of the concurrent production of electricity and heat using photovoltaic thermal (PV/T) technology. The efficiency performance of the PV/T system is meticulously analyzed using MATLAB/Simulink software environments. Notably, the proposed PV/T system shows reliable performance, and its validity is confirmed through experimental validation on a test stand with a single PV/T panel positioned at a 45-degree angle to the horizontal and a 0-degree azimuth angle.

The prohibitive costs of small-scale solar photovoltaic (PV) racks decreases PV adoption velocity. To overcome these costs challenges, an open hardware design method is used to develop two novel variable tilt racking designs. These are the first stilt mounted racking designs that allow manual change of tilt angle from zero to 90 degrees by varying the length of cables. The racks are designed using the calculated dead, wind and snow loads for Canada as conservative design for most of the rest of the world. Structural capacities of the wooden members are then ascertained and resisting bending moment, shear force, tensile force, and compressive force for them is calculated. A structural and truss analysis is performed to ensure that racking design with-stands the applicable forces. Moreover, implications of changing the tilt angle on the wooden members/cables used to build the system are also determined. The systems offer significant economic savings ranging from 1/3rd to 2/3rd the capital expenses of the commercially available alternatives. In addition, the racking designs are easy-to-build and require minimal manufacturing operations, which increases their accessibility. The stilt-mounted designs can be employed for agrivoltaic settings while allowing farm workers shaded ergonomic access to perform planting, weeding, and harvesting.

The rapid urbanization in China has significantly contributed to the vast expansion of urban built-up areas. Precisely extracting and monitoring these areas is crucial for understanding and optimizing the developmental process and spatial attributes of smart, compact cities. However, most existing studies tend to focus narrowly on a single city or global scale with a single dimension, often ignoring mesoscale analysis across multiple urban agglomerations. In contrast, our study employs GIS and image processing techniques to integrate multi-source data for the identification of built-up areas. We specifically compare and analyze two representative urban agglomerations in China: the Yangtze River Delta (YRD) in the east and the Chengdu-Chongqing (CC) region in the west. We use different methods to extract built-up areas from socio-economic factors, natural surfaces, and traffic network dimensions. Additionally, we utilize a high-precision built-up area dataset of China as a reference for verification and comparison. Our findings reveal several significant insights: (1) The multi-source data fusion approach effectively enhances the extraction of built-up areas within urban agglomerations, achieving higher accuracy than previously employed methods. (2) Our research methodology performs particularly well in the CC urban agglomeration. The average precision rate in CC is 96.03%, while the average precision rate in YRD is lower at 80.33%. This study provides an objective and accurate assessment of distribution characteristics and internal spatial structure of built-up areas within urban agglomerations. This method offers a new perspective for identifying and monitoring built-up areas in Chinese urban agglomerations.

Finding sustainable renewable energy sources for energy conversion and management is still an obscure topic. This paper presents a model-based simulation for an energy conversion system using piezoelectric energy harvester (PEH) technology. A dynamic mathematical model of a PEH device consists of a piezoelectric transducer, a controlled PWM rectifier, and a closed-loop buck boost converter is developed. A piezoelectric transducer converts mechanical vibrations from a wind force into an oscillating train of electrical charges. The sinewave peak-to-peak level relationship describes the changeable values of these charges, which depend on the severity of the wind vibration. The controlled PWM rectifier, in conjunction with a closed-loop buck-boost converter, converts this train of sinewave cycles into DC voltages. The control blocks of the closed-loop buck-boost converter use the perturbation and observation (P&amp;O) algorithm based on maximum power point tracking (MPPT), which adapts the operational voltage of the piezoelectric source to deliver the maximum power to load and improves the PEHS output voltage stability. A simulation program is employed to perform mathematical analysis on various wind vibration scenarios, piezoelectric sources without PWM converters, and piezoelectric vibration sources connected to a closed-loop P&amp;O converter. The crucial results of this paper demonstrate that the proposed dynamic PEHS model effectively feeds low-power electronic loads by directly adjusting the output voltage level to the set voltage, even under different vibration severity levels. As a result, the proposed PEHS dynamic model serves as a guideline for researchers in the development of self-powered sensors, which contributes to understanding sustainable energy alternatives.

In the early 2000s, matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF MS) emerged as a performant and relevant tool for identifying micro-organisms. Since then, it has become practically essential for identifying bacteria in microbiological diagnostic laboratories. In the last decade, it was successfully applied for arthropod identification allowing to distinguish vectors from non-vectors of infectious diseases. However, identification failures are not rare, hampering it widely use. Failure is generally attributed either to the absence of respective counter species MS spectra in the database, or to the insufficient quality of query MS spectra (i.e. lower intensity and diversity of MS peaks detected). To avoid matching errors due to non-compliant spectra, the development of a strategy for detecting and excluding outlier MS profiles became compulsory. To this end, we created MSProfileR, an R package leading to a bioinformatics tool through a simple installation, integrating the control quality system of MS spectra and an analysis pipeline including peak detection and MS spectra comparisons. MSProfileR can also add metadata concerning the sample that the spectra are derived from. MSProfileR has been developed in the R environment and offers a user-friendly web interface using the R Shiny framework. It is available on Microsoft Windows as a web browser application by simply navigation using the link of the package on the Github. MSProfileR is therefore accessible to non-computer specialists and is freely available to the scientific community. We evaluated MSProfileR using two datasets including exclusively MS spectra from arthropods. In addition to coherent sample classification, outlier MS spectra were detected in each dataset confirming the value of MSProfileR.

Amorphous Indomethacin has enhanced bioavailability over its’ crystalline forms, yet amorphous forms can still possess a wide variety of structures. Here, Empirical Potential Structure Refinement (EPSR) has been used to provide accurate molecular models on the structure of five different amorphous Indomethacin samples, that are consistent with their high energy x-ray diffraction patterns. It is found that the majority of molecules in amorphous Indomethacin are non-bonded or bonded to one neighboring molecule via a single hydrogen bond, in contrast the doubly bonded dimers found in the crystalline state. The EPSR models further indicate a substantial variation in hydrogen bonding between different amorphous forms, leading to a diversity of chain structures not found in any known crystal structures. The majority of hydrogen bonds are associated with the carboxylic acid group, although a significant number of amide hydrogen bonding interactions are also found in the models. Evidence of some dipole-dipole interactions are also observed in the more structurally ordered models. The results are consistent a distribution of Z-isomer intra-molecular type conformations in the more disordered structures, that dis-tort when stronger inter-molecular hydrogen bonding occurs. The findings are supported by 1H and 2H NMR studies of the hydrogen bond dynamics in amorphous Indomethacin.

To enable net zero sustainable thermal building energy this study develops an open-source thermal house model to couple solar photovoltaic (PV) and heat pumps (HP) for grid-connected residential housing. The calculation of both space heating and cooling thermal loads and the selection of HP is accomplished with a validated Python model for air-source heat pumps. The capacity of PV required to supply the HPs is calculated using an System Advisor Model integrated Python model. Self-sufficiency and self-consumption of PV and the energy imported/exported to the grid for a case study are provided, which shows that simulations based on the monthly load profile have a significant reduction of 43% for energy sent to/from the grid compared to the detailed hourly simulation and an increase from 30% to 60% for self-consumption and self-sufficiency. These results show the importance of more granular modeling and also indicate mismatches of PV generation and HP load based on hourly simulation datasets. The back-calculation PV sizing algorithm combined with HP and thermal loads presented in this study exhibited robust performance. The results indicate this approach can be used to accelerate the solar electrification of heating and cooling to offset the use of fossil fuels in northern climates.

It is shown that the gravitational mass-energy defect could be the main cause of Big Bang energy and triggering inflation in the newborn Universe.

Abstract: In order to accelerate deployment of distributed recycling by providing low-cost feed stocks of granulated post-consumer waste plastic, this study analyzes an open source waste plastic granulator system. It is designed, built and tested for its ability to convert post-consumer waste, 3-D printed products and waste into polymer feedstock for recyclebots of fused particle/granule printers. The technical specifications of the device are quantified in terms of power consumption (380 to 404W for PET and PLA, respectively) and particle size distribution. The open source device can be fabricated for less than USD$2000 in materials. The experimentally-measured power use is only a minor contribution to the overall embodied energy of distributed recycling of waste plastic. The resultant plastic particle size distributions were found to be appropriate for use in both recyclebots and direct material extrusion 3-D printers. Simple retrofits are shown to reduce sound levels during operation by 4dB-5dB for the vacuum. These results indicate that the open source waste plastic granulator is an appropriate technology for community, library, makespace, fab lab or small business-based distributed recycling.

The objective of the proposal is to find the optimal geometric shape of a photovoltaic panel that maximizes the collection of solar radiation. The optimal shape will be determined based on direct radiation, as it is the most relevant radiation for the photovoltaic process. To achieve this goal, we will use computer simulations to evaluate the performance of different geometric shapes under different conditions of solar radiation. Specifically, we will simulate the behavior of a photovoltaic panel with different shapes and orientations, and we will compare their energy yield over a given period of time. The simulations will be based on a mathematical model that takes into account the incidence angle of solar radiation on the panel, as well as other factors such as the reflection and absorption of radiation, and the temperature of the panel. The simulations will be carried out for different locations, with different solar radiation conditions, and for different periods of time, in order to obtain a comprehensive assessment of the performance of the different shapes. The results of the simulations will be analyzed to identify the optimal shape of the photovoltaic panel. This shape will be compared with the performance of flat panels, both static and with tracking systems, in order to evaluate the potential improvement in energy yield.

Of all the renewable energy sources, solar photovoltaic (PV) power is estimated to be a popular source due to several advantages such as its free availability, absence of rotating parts, integration to building such as rooftops, and less maintenance cost. The nonlinear current-voltage (I–V) characteristics and power generated from a PV array primarily depend on solar insolation/irradiation and panel temperature. The extracted PV output power is influenced by the accuracy with which the nonlinear power–voltage (P–V) characteristic curve is traced by the maximum power point tracking (MPPT) controller. In this paper, a bio-inspired roach infestation optimization (RIO) algorithm is proposed to extract the maximum power from the PV system (PVS). To validate the usefulness of the RIO MPPT algorithm, MATLAB/Simulink simulations are performed under varying environmental conditions, for example, step changes in solar irradiance, and partial shading of the PV array. Furthermore, the search performance of the RIO algorithm is examined on different unconstrained benchmark functions, and it is that realized that the RIO algorithm has improved convergence characteristics in terms of finding the optimal solution than Particle swarm optimization (PSO). The results demonstrated that the RIO-based MPPT performs remarkably in tracking with high accuracy as the PSO-based MPPT.

Solar energy is a renewable resource of energy that is broadly utilized and has the least emissions among the renewable energies. In this study, machine learning methods of artificial neural networks (ANNs), least squares support vector machines (LSSVM), and neuro-fuzzy are used for advancing prediction models for thermal performance of a photovoltaic-thermal solar collector (PV/T). In the proposed models, the inlet temperature, flow rate, heat, solar radiation, and the sun heat have been considered as the inputs variables. Data set has been extracted through experimental measurements from a novel solar collector system. Different analyses are performed to examine the credibility of the introduced approaches and evaluate their performance. The proposed LSSVM model outperformed ANFIS and ANNs models. LSSVM model is reported suitable when the laboratory measurements are costly and time-consuming, or achieving such values requires sophisticated interpretations.

Nanoparticles -- regularly patterned or randomly dispersed -- are a key ingredient for emerging technologies in photonics. Of particular interest are scattering and field enhancement effects of metal nanoparticles for energy harvesting and converting systems. An often neglected aspect in the modeling of nanoparticles are light interaction effects beyond classical electrodynamics stemming from electron dynamics in confined and accelerated systems. We give a detailed account on free electron phenomena in metal nanoparticles and discuss analytic expressions, stemming from microscopic and semi-classical theories. These can improve standard computational schemes to produce more reliable results on the optical properties of metal nanoparticles. We combine these solutions into a single framework and study their joint impact on isolated Au, Ag, and Al nanoparticles as well as dimer structures.

This article makes a general analysis of the supply chain of photovoltaic systems in Colombia, taking as a starting point a conceptual base and the current situation of the country in this sector. This article especially will contemplate the non-interconnected areas (ZNI) to the electricity grid in the national, due to its complexity in the logistics issues. Likewise, the work performs a graphical representation of the stages and processes of the supply chain using a powerful-modeled tool such as the Petri Nets (PNs). Finally, it identifies some of the flaws in the operation and the joint of all the links of the logistic part and from there it is based the importance of the strategy of orientation to the supply chain (SCO) as a possible alternative to improve and to enhance the logistic processes of this type of systems.

Neutron beams are an essential tool to investigate material structure and perform non-destructive analysis, as they give unique access to element composition, thus ideally complementing density analysis allowed by standard X-rays investigation. Laser-driven neutron sources, though compact and cost-effective, currently have lower average flux than conventional neutron sources, due to the limited repetition rate of the lasers used so far. However, advancements in laser technology allow nowadays to address this challenge. Here we report results obtained at the Advanced Laser Light Source (ALLS) characterizing stable production of broadband (0.1-2 MeV) neutrons produced at a high repetition rate (0.5 Hz). The interaction of laser pulses of 22 fs duration and 3.2 J on-target energy with 2-µm-thick tantalum targets produced protons in the Target Normal Sheath Acceleration (TNSA) regime up to 7.3 MeV. These protons were subsequently converted into neutrons by (p,n) reactions in Lithium fluoride (LiF). Activation measurements and bubble detectors were used to characterize neutron emissions, with a neutron fluence of up to ~ 1.4 × 10⁵ neutrons/shot/sr, and energies mainly between a few hundred of keV and 2 MeV. The total neutron yield was ~ 5 × 10⁵ neutrons/shot. This paves the way for numerous applications, e.g. in homeland security, material science or cultural heritage.

Because data authenticity and validity are becoming more and more of a concern in the digital age file security and integrity must be guaranteed. This paper investigates the application of HMAC-SHA256 which combines the Secure Hash Algorithm 256 (SHA256) with a private key for transmission-side source file authentication and verification. The study creates a prototype application to evaluate the efficacy of HMAC-SHA256 in securing file transfers by examining previous investigations on SHA and HMAC. The findings demonstrate that SHA256 produces unique file signatures which successfully guards against unwanted changes. Through the use of cryptographic hashes and secret keys to create distinct digital signatures that guarantee file authenticity HMAC improves security. The study shows that HMAC-SHA256 protects data integrity and detects tampering effectively. It does however stress how crucial it is to comprehend cryptographic concepts and apply these strategies with caution in order to prevent vulnerabilities. Overall the study finds that when properly implemented and updated HMAC-SHA256 greatly enhances file security in the digital age.

The study involves the creation of a solar-powered car that can travel up to 70 km with a maximum speed of 35.7 km/h, the vehicle mass is 300 kg. It stores some energy, which is then converted into electric energy that can be consumed by other electrical appliances, making it an electrical energy generator. The two back wheels are equipped with 3,000 W electric motors to enable movement. When the vehicle moves, power dissipates due to resistances that must be overcome to move it. Auxiliary components and the battery powering the system also require energy, resulting in not all power being transmitted to the electric vehicle's wheels. This article aims to create a prototype of the electric vehicle model. A model of the photovoltaic system, considering the geographic coordinates and solar parameters of the location, as well as the BLDC motor and vehicle dynamics, is required to examine the component behavior based on the observable parameters. These pa-rameters consist of the resistive torque, angular speed, and resistance values that need to be overcome to evaluate the electric vehicle's performance. Once the lost power has been determined, the remaining power will be allocated to power other electrical devices. The variations in the parameters considered are crucial for the performance of an electric vehicle equipped with a photovoltaic and mechanical power supply system, as one of the sources of our prototype is mechanical and provides 400 W of power.

Solar photovoltaic (PV) technology is a cornerstone of the global effort to transition towards cleaner and more sustainable energy systems. This paper explores the pivotal role of PV technology in re-ducing greenhouse gas emissions and combatting the pressing issue of climate change. At the heart of its efficacy lies the efficiency of PV materials, which dictates the extent to which sunlight is transformed into electricity. Over the last decade, substantial advancements in PV efficiency have propelled the widespread adoption of solar PV technology on a global scale. The efficiency of PV materials is a critical factor, determining how effectively sunlight is transformed into electricity. Enhanced efficiency, achieved through a decade of progress, has driven the global expansion of solar PV. Multi-junction photovoltaic materials have now exceeded 40% efficiency in lab tests. China leads the world in solar PV installations, boasting over 253 GW of installed capacity by the end of 2021. Other prominent countries in this sector are the United States, Japan, Germany, and India. Supportive policies like feed-in tariffs, net metering, tax incentives, and cost reductions in PV modules have made solar PV increasingly competitive against fossil fuel-based power generation. Solar PV technology holds immense potential for creating a cleaner, reliable, scalable, and cost-effective electricity system. To expedite its deployment and foster a more sustainable energy future, continued investment in research and development, along with supportive policies and market mechanisms, is essential. This paper underscores the pivotal role of solar PV technology in the global energy transition and advocates for a concerted effort to unlock its full potential in achieving a more sustainable and resilient energy future.

This study is focused on an optimal sizing method based on genetic algorithms (GA) in order to design a high-performance photovoltaic system that would be installed in the Alioune Diop University of Bambey, Senegal. The multi-objective optimization allowed us to find a better trade- off between the Total Life Cycle cost (TLCC) and the Loss of Power Supply Probability (LPSP). The goal is to minimize the TLCC while maintaining a good satisfactory of the system with a desired LPSP, under certain constraints. The expressions of the TLCC and the LPSP are established according to the total photovoltaic energy and the battery capacity. The toolbox of Matlab software is used to implement the optimization problem with twelve blocks of the site and its different corresponding loads. The obtained results have led to a several combinations of the photovoltaic and battery capacities of which the best one is selected based on the lowest LPSP, that guaranteed a better load coverage during the night. The results of this proposed method are compared with intuitive method that has been firstly applied. For the block with the lowest load demand, the proposed optimization model leads to a reduction a reduction of 70% and 48% in the storage capacity and the TLCC respectively for a LPSP of 0.007 %.

The energy yield of the Vehicle-integrated photovoltaic (VIPV) differs from that of the standard photovoltaics (PV). It is mainly by the difference of the solar irradiance onto the car-roof and car-bodies as well as its curved-shape. Both meaningful and practical modeling and measurement of the solar irradiance for VIPV are needed to be newly established, not the extension of the current technologies. The solar irradiance was modeled by a random distribution of the shading objects and car-orientation with the correction of the curved surface of the PV modules. The measurement of the solar irradiance onto the car-roof and car-body was done using five pyranometers in five local axes on the car for one year. The measured dynamic solar irradiance onto the car-body and car-roof was used for validation of the solar irradiance model in the car.

The advantage of FPGAs lies in the ability to implement a fully hardware solution for interfacing with various input/output (I/O) devices. Each block can work in parallel with all the others, simplifying the satisfaction of timing constraints. However, this hardware utilization consumes FPGA resources that could otherwise be allocated to the primary project. An alternative involves employing a small "soft-core" processor implementing I/O in software. With the goal to design and evaluate a new tiny soft-core processor optimized for FPGA resources in I/O , a novel processor named Baby8 is developed. It is an 8-bit CISC soft-core processor optimized for reduced FPGA resources including program size for 8-bit applications. The number of instructions is not large but any instruction can access arbitrary memory locations. The performance and resource utilization of the newly designed processor are evaluated and compared with a variety of other soft-core processors. The results demonstrate its competitive performance, achieving an average maximum clock frequency of approximately 57 MHz and a power consumption of around 2mW. Furthermore, it conserves nearly half of the FPGA resources in implementation.

This study aimed to identify the most beneficial attitudes adopted by enterprise participants during their engagement in open-source software (OSS) activities. For this purpose, we selected repositories from GitHub, featuring the top 10 with the highest stars and forks, classified the participants according to their sentiment states, and compared their productivity. The results indicated that participants with positive sentiments were more productive than those with negative sentiments. Consequently, it can be inferred that encouraging organizations to express positive sentiments towards their developers publicly may stimulate OSS community activities and enhance productivity, thereby potentially leading to increased open innovation and sustainability.

he paper offers an innovative cooking utensil design for remote, isolated, and even peri-urban communities at a low price, with high reliability and simple construction. It can alleviate energy poverty and improve food security. This utensil uses only local solar energy directly and allows comfortable indoor cooking. This paper provides the design principles of a solar cooker/frying pan or generic heater, based on a PV panel or a plurality of them, which are directly connected to a plurality of Positive Thermal Coefficient (PTC) resistors to match the power. PTCs are nowadays produced in massive quantities and are widely available at low cost. The proposed device does not require an electronic controller or a battery for its operation. The aim is for family use, although the design can be easily scaled to a larger size or power, maintaining its simplicity. Electric heating inside or attached to the cooking pot, plus the temperature self-limiting effect of PTCs, allows for thermally insulating the cooking pot from its outside using ordinary materials. Insulation en-hances energy efficiency during cooking and keeps cooked food warm for a long time. Clean development would receive a significant impulse with its application. A simple mathematical model describes its functioning and states guidelines for adequate design. The results indicate a successful proof of concept and high efficiency both for water and oil as representatives of cooking.

Higher concentrations of greenhouse gases resulting from anthropogenic actions associated with energy generation are one of the causes of climate change. In view of this, several efforts have been undertaken in the search for more sustainable alternatives, and photovoltaic (PV) technology has stood out among the different possibilities. However, PV generation is highly sensitive to future climate variability, which is a source of uncertainty that can complicate energy planning and compromise the viability of systems. This theme has received attention from the academic community, but some challenges to map and identify relevant literature have been encountered. Therefore, this study was conducted to analyze and identify relevant aspects of international scientific production on the impacts of climate change on the potential of photovoltaic production, CC-PVP, through bibliometric techniques. For this, 3900 articles from the Web of Science and Scopus databases, published between 1960 and 2021, were retrieved and analyzed through a bibliometric approach, using the SciMAT tool. Among the results obtained, it is worth pointing out that the CC-PVP research field (i) has moderate maturity, (ii) is concentrated in the areas of energy, fuels and technology, as well as environmental sciences and meteorology, (iii) has the most studied themes currently related to energy and the forecasting of photovoltaic energy production and electric energy consumption in the world, especially when considering climate change, and (iv) is more researched by Chinese, North Americans and Australians.

Efficient energy extraction in photovoltaic (PV) systems relies on the effective implementation of Maximum Power Point Tracking (MPPT) methods. Conventional MPPT techniques often suffer from slow convergence speeds and suboptimal tracking performance, particularly under dynamic variation of environmental conditions. Smart optimization algorithms (SOA) using metaheuristic optimization algorithms can avoid this limitation inherent in the conventional MPPT methods. The problem of slow convergence of the SOA is avoided in this paper using a novel strategy called Swarm Size Reduction (SSR) utilized with Particle Swarm Optimization (PSO) algorithm, specifically designed to achieve short convergence time (CT) while maintaining exceptional tracking accuracy. The novelty of the proposed MPPT method introduced in this paper is the dynamic reduction of the swarm size of the PSO for improved performance of the MPPT of the PV systems. This adaptive reduction approach allows the algorithm to efficiently explore the solution space of PV systems and rapidly exploit to identify the global maximum power point (GMPP) even under fast fluctuation of uneven solar irradiance and temperature. This pioneering ultra-fast MPPT method represents a significant advancement in PV system efficiency and promotes the wider adoption of solar energy as a reliable and sustainable power source. The novel adaptive PSO algorithm also opens new possibilities for further innovations in optimization-driven applications, extending its potential impact on a diverse range of real-world challenges. The results obtained from this proposed strategy are compared with several optimization algorithms to validate its superiority.

As renewable energy generation prediction system has been introduced into the energy trading market, making a model to accurately predict the quantity of solar photovoltaic (PV) energy generation has become a significant problem. Moreover, to encourage an accurate prediction of the quantity of energy generation, an incentive system has been implemented for those who predict the quantity of solar PV energy under the error rate of 8%. Therefore, it has become more important to investigate and analyze current prediction technology numerically and develop more advanced prediction system. In this study, we tried to develop a better model to improve the accuracy of solar PV energy generation quantity by comparing three models made with gradient boosting machine (GBM), Model 1, Model 2, Model 3 respectively. Model 1 was built with the whole training data set without any additional preprocessing. After conducting some additional preprocessing procedure to predict solar energy generation more accurately, we made Model 2 with the whole training data set and Model 3 with only upper 10% of energy generation capacity. To compare the accuracy of three models, normalized mean absolute error (nMAE) was used as an evaluation index. The nMAE of Model 1 was 9.64% while the Model 2 showed 8.41%. Also, Model 3, which was constructed with the training set of upper 10% energy generation capacity, outperformed with the nMAE of 8.08%. For further study, to check the effectiveness of models constructed with GBM, a time series model, autoregressive integrated moving average (ARIMA), was also built and the nMAE was compared.

In recent years, intensive work has been carried out to achieve maximum energy production in photovoltaic power plants. Today, this challenge has to be solved for arrays of solar panels that move with the object on which they are installed (vehicles, trucks, ships, etc.). The present work tries to find the best solution for both constant voltage systems and for cases of maximum intensity. Once found, these solutions will be applied in real time for the dynamic recharging of battery packs, trying to achieve energetically autonomous vehicles.To solve these situations, a new computational method of voltage and amperage calculation has been developed in this paper, based on Dijkstra’s minimum path finding algorithm on graph theory, adapted to electrical circuits. For this purpose, panel performance analysis sensors, developed at the University of Malaga, have been combined with different electronic solutions (wifi relay devices using esp8266 or similar chips) achieving an accurate and sufficiently fast solution at very low cost. With this, series or parallel configurations can be carried out depending on the type of energy generation sought. The theoretical solutions using Minkowski paths, achieved in the past, have been simulated and subsequently constructed in this article, indicating the diagrams necessary for their realisation.

As Solar Photovoltaics in buildings reaches maturity, grid integration and economic yield are topics of greater interest. The traditional design of photovoltaic installations has considered the optimal orientation of photovoltaic modules to be that which yields the maximum annual energy production. The influence of the consumption patterns and the hourly-variable electricity prices implies that this traditional optimal design might not be the most profitable. Using a full-year dataset for a residential installation, alternative installations using canopies and modules attached to the façades are simulated. Simulating the energy balances for different annual consumptions, it is found that the canopy and façade installations offer better self-consumption of the PV produced energy, reflected in a 9% higher self-consumption degree using modules on façades and a 5% using canopies. The economic evaluation under the new electricity tariffs in Spain shows a better profit for PV self-consumption, reducing by more than 2 years the time of return on investment. The analysis of different alternatives for an industrial PV has allowed us to identify several benefits for these orientations, such as an increase in annual energy production of up to 59% over the optimal-producing orientation, that are confirmed after several months of operation.

One of the important research directions in the field of photovoltaics is integration with construction. The integration of solar cell systems with a building can reduce installation costs and help optimize the used space. One of the interesting types of cells is dye-sensitized solar cells. In addition to their interesting properties, they also have aesthetic value. In the classic arrangement, they are constructed using glass with a transparent conductive layer (TCL). This article describes replacing a classic glass counter electrode with an electrode based on a ceramic tile and nickel foil. This solution makes it possible to expand their construction applications. The advantage of this solution is full integration with construction while simultaneously generating electricity. A dye-sensitized solar cell was built layer-by-layer on ceramic tile and nickel foil. An atomization method was used to deposit fluorine-doped tin oxide, and then a screen printing method was used to deposit a platinum layer. The electrical parameters of the manufactured DSSCs with and without a counter electrode tile were characterized by measuring their current-voltage characteristics under standard AM 1.5 radiation. A dye-sensitized solar cell integrated with ceramic tiles and nickel foil was produced and displayed an efficiency of over 4%.

Light management in single nanowires (NWs) is of great importance for photovoltaic applications. However, square NWs (SNWs) can limit their light-trapping ability due to high geometrical symmetry. In this work, we present a detailed study of light management in single silicon NWs with a rectangular cross-section (RNWs). We demonstrate that the RNWs exhibit significantly enhanced light-harvesting compared with the SNWs, which can be attributed to the symmetry-broken structure that can orthogonalize the direction of light illumination and the leaky mode resonances (LMRs). That is, the rectangular cross-section can simultaneously increase the light path length by increasing the vertical side and reshape the LMR modes by decreasing the horizontal side. We found that the light absorption can be engineered via tuning the horizontal and vertical sides, the photocurrent is significantly enhanced by 276.5% or 82.9% in comparison with that of the SNWs with the same side length as the horizontal side of 100 nm or the vertical side of 1000 nm, respectively. This work advances our understanding of how to improve light-harvesting based on the symmetry breaking from the SNWs to RNWs and provides an effective way for designing high-efficiency single NW photovoltaic devices.

This paper describes the proposal and development of a proof of concept (PoC) for a data logger system designed for operation and fault detection in bench testing of combustion engines. The main objective was to develop a data logger system that collects data on vibration, sound, temperature, and CO2 levels to identify ignition and combustion faults, thereby contributing to reducing greenhouse gas emissions (GHG). The paper presents (i) the proposal and development and (ii) the open-source code: proof of concept for a data logger system focused on detecting faults and monitoring the operational condition of benchtop combustion engines. The results indicate the feasibility of the PoC for data acquisition and dataset creation for Research and Development purposes.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

The research work explores the impact of temperature on Silicon photovoltaic (PV) panels considering Nigeria as case study. It is found that high solar radiation in Nigeria increases surface temperature of PV panel above 25oC of optimal operating temperature of PV panels. Redundant energy gain from incident solar energy is dissipated at the rear of PV panels as heat, which reduces the efficiency of PV panel. Cooling mechanism is needed to cool the PV panels to increase the efficiency. In this study we demonstrated a unique design of a bifunctional photovoltaic-thermal (PVT) system by employing heat exchanger at the rear of PV panel and water is used as a working fluid that is circulated through the heat exchanger to remove the excess heat. It is observed from the simulation results that Maiduguri peak annual electrical power output gives 1907kWh/kWp which is the highest, because of high solar radiation average of 727W/m2 in a year. And for Makurdi the peak annual electrical power output of 1542kWh/kWp while for Port Harcourt the peak power output of 1355kWh/kWp respectively. Interestingly, Polycrystalline Si-PV surface temperature decrease from 49.25oC to 38.38oC. Electrical power increased from 1526.83W to 1566.82W in a day and efficiency increase from 13.99% to 15.01%.

Industry 4.0 is in continuous technological growth that benefits all sectors of industry and society in general. This article reviews the concept of Digital Twin (DT) and the interest of its application in photovoltaic installations. A comparison is made on how other authors use the DT approach in photovoltaic installations to improve the efficiency of the renewable energy generated and consumed, the energy prediction and the reduction of the operation and maintenance costs of the photovoltaic installation. It is reviewed how, by providing real-time data and analysis, DTs enable more informed decisions in the solar energy sector. The objectives of the review are to study the digital twin technology and to analyze its application and implementation in photovoltaic systems.

Sustainable agriculture has become increasingly important in Tunisia due to the drought that has been affecting the country's climate in recent years. This has become a major threat to the economy, making it necessary to explore alternative methods of agriculture that are more sustainable. Moreover, smart hydroponic cultivation based on renewable energies has become increasingly widespread, promoting the quality and efficiency of agricultural production despite weather parameters variations and global warming. This work aims to create a sustainable agriculture system in Tunisia through the design and implementation of a smart photovoltaic (PV) hydroponic greenhouse. The greenhouse will utilize advanced technology to optimize plant growth and reduce water usage, while also incorporating solar panels to generate renewable energy. The end goal is to create a self-sufficient and eco-friendly agricultural system that can provide fresh produce to local communities year-round. In this work, we are interested to the automation of the hydroponic greenhouse (HG)’s thermal conditioning system based on an asynchronous motor pump and powered by a PV generator. In the first stage, we analyzed the mathematical modeling of a stand-alone PV-HG system that consists of a PV generator, a three-phase inverter, an asynchronous motor pump, and a hydroponic system. After that, we developed a Field Oriented Control based on proportional integral (PI) regulators to adjust the rotation speed of the asynchronous motor pump, which aimed to provide the cooling and heating needs of the plant. The simulation results demonstrated the effectiveness of the proposed system . Additionally, we designed and implemented a smart system based on the internet of things (IoT) to enable remote control of internal and external parameters of the HG. This intelligent solution utilizes sensors, microcontrollers, and other devices and ensures the monitoring and the maintaining of the ideal growing conditions for our plants, guaranteeing that they receive the proper amount of temperature, humidity, and lighting. This type of system can be an invaluable tool for maximizing yields and achieving optimal results. With the right approach and attention to detail, we can create a sustainable and efficient growing environment that will help our plants flourish year-round.

As renewable energy generation prediction systems have been introduced into the energy trading market, accurate prediction of solar photovoltaic (PV) energy generation has become a crucial challenge for ensuring stable trade of variable energy. Therefore, it is essential to quantitatively investigate and analyze current prediction technology and develop more advanced prediction systems. In this study, three models for predicting PV energy generation were investigated. Multiple regression, random forest, and gradient boosting machine (GBM) models were con-structed for 15 utility-scale power plants throughout South Korea. Model performance was evaluated in terms of root mean square error (RMSE) and mean absolute error (MAE). The multiple regression-based model had an RMSE of 12.00% and MAE of 9.06%. The random forest model had an RMSE of 11.69% and MAE of 8.61%. The GBM model had an RMSE of 11.34% and MAE of 8.18%, indicating its superior accuracy among the three models in predicting PV energy generation. These findings provide valuable insights that may contribute to the development of advanced PV energy generation models and their application in grid operations.

The rapid development of the photovoltaic (PV) industry will result in an increase in the amount of electrical and electronic waste from used PV panels. Only in Poland, the total capacity installed in photovoltaic sources in Poland in May 2020 exceeded 1,950 MW, and the installation weight was approximately 120,000. tone. The problem arises in the recycling or management of this waste. This work presents methods used to recycle waste into photovoltaic modules. The authors investigated the possibility of mechanical and chemical processing of crystalline silicon. A method of thermal treatment of the panel was also proposed. As a result of the research, it was found that the stage of separating materials (crystalline cream, EVO foil, aluminum frame) plays an important role in the recycling process, which is not easy. Chemical treatment allows the silicon to become plastic and the temperature melts the back layer of the panel.

The Source Region of the Yellow River (SRYR), renowned as the "Water Tower of the Yellow River", serves as an important water conservation domain in the upper reaches of the Yellow River, significantly influencing water resources within the basin. Based on the Weather Research and Forecasting (WRF) Model Hydrological modeling system (WRF-Hydro) model, the key variables of the atmosphere-land-hydrology coupling processes over the SRYR during the 2013 rainy season are analyzed. The investigation involves a comparative analysis between the coupled WRF-Hydro and the standalone WRF simulations, focusing on the hydrological response to the atmosphere. The results reveal that the WRF-Hydro model's proficiency in depicting streamflow variations over the SRYR, yielding a Nash Efficiency Coefficient (NSE) of 0.44 and of  0.61 during the calibration and validation periods, respectively. Compared to the standalone WRF simulations, the coupled WRF-Hydro model demonstrates enhanced performance in soil heat fluxes simulations, reducing the mean Root Mean Square Error (RMSE) of surface soil temperature by 0.96 K and soil moisture by 0.01 m\textsuperscript{\textsuperscript{3}}/m\textsuperscript{\textsuperscript{3}}. Furthermore, the coupled model adeptly captures the streamflow variation characteristics with the NSE of 0.33. This underscores the significant potential of the coupled WRF-Hydro model for delineating coupled atmosphere-land-hydrology processes in regions characterized by cold climates and intricate topography.

Let $(A,\Delta)$ be a {\it weak multiplier Hopf algebra} as introduced in [VD-W3] (see also [VD-W2]). It is a pair of a non-degenerate algebra $A$, with or without identity, and a coproduct $\Delta$ on $A$, satisfying certain properties. If the algebra has an identity and the coproduct is unital, then we have a Hopf algebra. If the algebra has no identity, but if the coproduct is non-degenerate (which is the equivalent of being unital if the algebra has an identity), then the pair would be a multiplier Hopf algebra. If the algebra has an identity, but the coproduct is not unital, we have a weak Hopf algebra. In the general case, we neither assume $A$ to have an identity nor do we assume $\Delta$ to be non-degenerate and so we work with a {\it genuine} weak multiplier Hopf algebra. It is called {\it regular} if its antipode is a bijective map from $A$ to itself. \snl In this paper, we {\it continue the study of weak multiplier Hopf algebras}. We recall the notions of the source and target maps $\varepsilon_s$ and $\varepsilon_t$, as well as of the source and target algebras. Then we investigate these objects further. Among other things, we show that the canonical idempotent $E$ (which is eventually $\Delta(1)$) belongs to the multiplier algebra $M(B\ot C)$ where $B=\varepsilon_s(A)$ and $C=\varepsilon_t(A)$ and that it is a {\it separability idempotent} (as studied in [VD4.v2]). If the weak multiplier Hopf algebra is regular, then also $E$ is a {\it regular} separability idempotent. \snl We also consider {\it special cases and examples} in this paper. In particular, we see how for any weak multiplier Hopf algebra $(A,\Delta)$, it is possible to make $C\ot B$ (with $B$ and $C$ as above) into a new weak multiplier Hopf algebra. In a sense, it forgets the 'Hopf algebra part' of the original weak multiplier Hopf algebra and only remembers the source and target algebras. It is in turn generalized to the case of any pair of non-degenerate algebras $B$ and $C$ with a separability idempotent $E\in M(B\ot C)$. We get another example using this theory associated to any discrete quantum group (a multiplier Hopf algebra of discrete type with a normalized cointegral). Finally we also consider the well-known 'quantization' of the groupoid that comes from an action of a group on a set. All these constructions provide interesting new examples of weak multiplier Hopf algebras (that are not weak Hopf algebras).

Human number understanding is thought to rely on the analogue number system (ANS), working according to Weber’s law. We propose an alternative account, suggesting that symbolic mathematical knowledge is based on a discrete semantic system (DSS), a representation that stores values in a semantic network, similar to the mental lexicon or to a conceptual network. Here, focusing on the phenomena of numerical distance and size effects in comparison tasks, first we discuss how a DSS model could explain these numerical effects. Second, we demonstrate that DSS model can give quantitatively as appropriate a description of the effects as the ANS model. Finally, we show that symbolic numerical size effect is mainly influenced by the frequency of the symbols, and not by the ratios of their values. This last result suggests that numerical distance and size effects cannot be caused by the ANS, while the DSS model might be the alternative approach that can explain the frequency-based size effect.

As an important part of coastal wetlands, tidal flats provide unique ecosystem services and functions. China's tidal flats are significantly threatened by industrialization, urbanization, aquaculture expansion and coastline reconstruction, and there is an urgent need for sustainable strategies to balance the protection and utilization of tidal flats. Remote sensing technology can realize large-scale spatiotemporal research of tidal flats, comprehensively improve the ecological environment of coastal zones, and help achieve the overall planning goals of major projects for the protection and restoration of important ecosystems in China. In this study, based on GEE (Google Earth Engine) platform, Sentinel-2 (MSI), Landsat 8 (OLI) and Landsat 9 (OLI-2) remote sensing images were used to construct multi-source intensive time series remote sensing image collection, combined with MSIC-OA algorithm. The tidal flat data of China in 2018 and 2023 are extracted and analyzed. The results show as follows: 1) The overall classification accuracy of the tidal flat in 2023 is 95.19%, and the Kappa coefficient is 0.89; In 2018, they were 92.77% and 0.83 respectively. 2) The total tidal flat area in 2018 and 2023 is 8300.34km2 and 8151.54km2, respectively, a decrease of 148.80km2; 3) In 2023, estuarine and bay tidal flats will account for 54.88% of the total area, and most of the tidal flats will be distributed near river inlets and bays; 4) In 2023, the total length of the coastline adjacent to the tidal flat is 10196.17km, of which the artificial shoreline accounts for 67.06%, and the development degree of the tidal flat is 2.04, indicating that most of the tidal flat has been developed and utilized. The research results provide valuable reference for the scientific planning and rational utilization of tidal flat resources in China.

Power grid fault diagnosis technology has been widely used at home and abroad. With the access of distributed power sources and diversified loads, the distribution network has changed from a passive network to an active network, and the current has changed from "one-way" to "two-way". The structure of distribution network, equipment environment and operating conditions are becoming more and more complex, and the fault diagnosis and localization of active distribution network is becoming more and more difficult. With the rapid development of artificial intelligence, power grid fault diagnosis based on intelligence is unprecedented. This paper introduces the research status of distributed photovoltaic grid-connected fault diagnosis technology, and expounds the history of fault diagnosis technology, which mainly includes expert system, artificial neural network, Bayesian network, fuzzy set theory, rough set theory, Petri net analytical model and multi-source information fusion, etc. The applicability and characteristics of these diagnoses are described, and the existing defects and the overall direction of improvement are briefly described Finally, the key technical problems and future directions in the field of power system fault diagnosis are pointed out by combining theory with practice, so as to promote the further development of this field.

This article presents the development of an innovative Maximum Power Point Tracking (MPPT) strategy, utilizing a Particle Swarm Optimization (PSO) algorithm to improve the effectiveness of PV systems and expedite convergence. The new MPPT method incorporated a unique Swarm Self-Reinforcement Mechanism (SSRM) within the PSO algorithm, targeting quick convergence and excellent tracking accuracy. This approach enables the PSO to eliminate the fitness function that has the lowest value and subsequently reinforce it in the next iteration, revolving around the global maximum power point (GMPP). By applying this novel PSO-based method, the MPPT performance of PV systems was significantly improved, facilitating the algorithm to proficiently navigate through the solution space and quickly locate the GMPP, even in rapidly changing environmental conditions. The outcomes derived from this novel approach were contrasted with other algorithmic optimization methods, validating its superior convergence speed and tracking accuracy. Different swarm sizes were examined using SSRM, and the optimal swarm size for the system employing MPPT was identified to achieve the lowest convergence time (CT). The results showcased the impressive performance capabilities of this novel strategy, resulting in a time con-traction of up to 28% compared to the conventional PSO technique, where the optimal swarm size was found to be 5. This achievement marks a significant milestone in the evolution of PSO-based MPPT techniques, and paves the way for future advancements in this exciting field.

The aim of the study was to find the effect of polyethylene (PE) coatings on the short-circuit current of silicon photovoltaic cells covered with glass, in order to improve the short-circuit current of the cells. Various combinations of PE films (thicknesses ranging from 9 to 23 µm, number of layers ranging from 2 to 6) with glasses (greenhouse, float, optiwhite and acrylic glass) were investigated. The best current gain of 4.05% was achieved for the coating combining a 1.5 mm-thick acrylic glass with 2 × 12 µm-thick PE films. This effect can be related to the formation of an array of micro-wrinkles and micrometer-sized air bubbles with a diameter of 50 to 600 µm in the films, which serve as micro-lenses and enhance light trapping.

We investigate the performance of a novel flat photovoltaic-thermal (PV-T) module under high-vacuum through a 1D numerical model based on steady-state energy balance, with the aims of optimizing the simultaneous production of thermal and electrical energy. In the proposed design, the photovoltaic (PV) cell is positioned directly above the selective solar absorber (SSA), in a multilayer or fully integrated PV-SSA structure, which allows full exploitation of spectral solar radiation. In fact, in this configuration the losses related to non-absorption of low-energy photons and thermalization, typical of a classical single-junction PV cell, are reduced. The present study is conducted as the emittance and energy bandgap of the PV layer varied, thus admitting a wide variety of materials into the analysis. The dependence of the temperature coefficient, β(%/K), on the energy bandgap of the PV cell is also included. In the last part of the work, we discuss the performance of the proposed evacuated PV-T equipped with a SSA layer and thin film solar cells, namely those made of CdTe, CdS and GaAs. Overall, the paper highlights the great advantage of using high vacuum insulation, which suppresses conductive losses, and the versatility of the proposed system, which could be adapted to the user's needs simply by choosing the appropriate material for the photovoltaic layer.

The power-generation capacity of grid-connected photovoltaic (PV) power systems is increasing. As output power forecasting is required by electricity market participants and utility operators for the stable operation of power systems, several methods have been proposed using physical and statistical approaches for various time ranges. A short-term (30 min ahead) forecasting method has been previously proposed by our laboratory for geographically distributed PV systems using motion estimation. This study focuses on an important parameter for estimating the proposed motion and optimizing the parameter. This parameter is important because it is associated with the smoothness of the vector field, which is the result of motion estimation and influences the forecasting accuracy. In the periods with drastic power output changes, the evaluation was conducted on 101 PV systems located within a circle of 15-km radius in the Kanto region of Japan. The results indicate that the absolute mean error of the proposed method with the optimized parameter is 10.3%, whereas that of the persistent prediction method is 23.7%. Therefore, the proposed method is effective in forecasting for periods when PV output changes drastically in a short time.

This paper presents a concise exploration of several analytical methods for extracting the parameters of the single-diode model (SDM) of a photovoltaic (PV) module under standard test conditions (STC). The paper investigates six methods and presents the detailed mathematical analysis leading to the development of each method. To evaluate the performance of these methods, MATLAB-based software has been developed and deployed to synthesize the results of each method when used to extract the SDM parameters of various PV test modules of different PV technologies. Similar software has also been developed to extract the same parameters using well-established numerical and iterative techniques. A comparison is subsequently made between the synthesized results and those obtained using numerical and iterative methods. The comparison indicates that in spite of the fact that analytical methods may involve fair amount of approximations, their accuracy can be comparable to that of their numerical and iterative counterparts, with the added advantage of significant reduction in computational complexity, and without the initialization and convergence difficulties, which are normally associated with numerical methods.