BBC Russian

Research

12 pages, 7734 KiB

Open AccessArticle

Investigation of Failure Mechanisms in Oil-Lubricated Rolling Bearings under Small Oscillating Movements: Experimental Results, Analysis and Comparison with Theoretical Models

by Fabian Halmos, Sandro Wartzack and Marcel Bartz

Lubricants 2024, 12(8), 271; https://doi.org/10.3390/lubricants12080271 - 29 Jul 2024

Viewed by 248

Abstract

Bearing life calculation is a well-researched and standardized topic for rotating operation conditions. However, there is still no validated and standardized calculation for oscillating operation, only different calculation approaches. Due to the increasing number of oscillating rolling bearings, for example, in wind turbines, [...] Read more.

Bearing life calculation is a well-researched and standardized topic for rotating operation conditions. However, there is still no validated and standardized calculation for oscillating operation, only different calculation approaches. Due to the increasing number of oscillating rolling bearings, for example, in wind turbines, industrial robots, or 3D printers, it is becoming more and more important to validate one of these approaches or to formulate a new one. In order to achieve this goal, the damage mechanisms for oscillating operating conditions must first be analyzed in more detail by means of experimental investigations. The open question is whether fatigue is the relevant damage mechanism or whether wear damage, such as fretting corrosion or false brinelling, dominates. The present work therefore shows under which oscillation angle and frequency fatigue occur in oil-lubricated cylindrical roller bearings. Full article

(This article belongs to the Special Issue Tribology in Germany: Latest Research and Development)

► Show Figures

Figure 1

37 pages, 32174 KiB

Open AccessArticle

Improved Operating Behavior of Self-Lubricating Rolling-Sliding Contacts under High Load with Oil-Impregnated Porous Sinter Material

by Nicolai Sprogies, Thomas Lohner and Karsten Stahl

Lubricants 2024, 12(7), 259; https://doi.org/10.3390/lubricants12070259 - 21 Jul 2024

Viewed by 447

Abstract

Resource and energy efficiency are of high importance in gearbox applications. To reduce friction and wear, an external lubricant supply like dip or injection lubrication is used to lubricate tribosystems in machine elements. This leads to the need for large lubricant volumes and [...] Read more.

Resource and energy efficiency are of high importance in gearbox applications. To reduce friction and wear, an external lubricant supply like dip or injection lubrication is used to lubricate tribosystems in machine elements. This leads to the need for large lubricant volumes and elaborate sealing requirements. One potential method of minimizing the amount of lubricant and simplifying sealing in gearboxes is the self-lubrication of tribosystems using oil-impregnation of porous materials. Although well established in low-loaded journal bearings, self-lubrication of rolling-sliding contacts in gears is poorly understood. This study presents the self-lubrication method using oil-impregnated porous sinter material variants. For this, the tribosystem of gear contacts is transferred to model contacts, which are analyzed for friction and temperature behavior using a twin-disk tribometer. High-resolution surface images are used to record the surface changes. The test results show a significant increase in self-lubrication functionality of tribosystems by oil-impregnated porous sinter material and a tribo-performance comparable to injection-lubricated tribosystems of a sinter material with additionally solid lubricant added to the sinter material powder before sintering. Furthermore, the analyses highlight a significant influence of the surface finish, and in particular the surface porosity, on the overall tribosystem behavior through significantly improved friction and wear behavior transferable to gear applications. Full article

(This article belongs to the Special Issue Tribology in Germany: Latest Research and Development)

► Show Figures

Figure 1

15 pages, 4186 KiB

Open AccessArticle

Numerical Simulations and Experimental Validation of Squeeze Film Dampers for Aircraft Jet Engines

by Markus Golek, Jakob Gleichner, Ioannis Chatzisavvas, Lukas Kohlmann, Marcus Schmidt, Peter Reinke and Adrian Rienäcker

Lubricants 2024, 12(7), 253; https://doi.org/10.3390/lubricants12070253 - 13 Jul 2024

Viewed by 417

Abstract

Squeeze film dampers are used to reduce vibration in aircraft jet engines supported by rolling element bearings. The underlying physics of the squeeze film dampers has been studied extensively over the past 50 years. However, the research on the SFDs is still ongoing [...] Read more.

Squeeze film dampers are used to reduce vibration in aircraft jet engines supported by rolling element bearings. The underlying physics of the squeeze film dampers has been studied extensively over the past 50 years. However, the research on the SFDs is still ongoing due to the complexity of modeling of several effects such as fluid inertia and the modeling of the piston rings, which are often used to seal SFDs. In this work, a special experimental setup has been designed to validate the numerical models of SFDs. This experimental setup can be used with various SFD geometries (including piston ring seals) and simulate almost all conditions that may occur in an aircraft jet engine. This work also focuses on the inertia forces of the fluid. The hydrodynamic pressure distribution of a detailed 3D-CFD model is compared with the solution of the Reynolds equation including inertia effects. Finally, the simulation results are compared with experimental data and good agreement is observed. Full article

(This article belongs to the Special Issue Tribology in Germany: Latest Research and Development)

► Show Figures

Figure 1

17 pages, 5142 KiB

Open AccessArticle

Modelling of Static and Dynamic Elastomer Friction in Dry Conditions

by Fabian Kaiser, Daniele Savio and Ravindrakumar Bactavatchalou

Lubricants 2024, 12(7), 250; https://doi.org/10.3390/lubricants12070250 - 9 Jul 2024

Viewed by 683

Abstract

Understanding the tribological behavior of elastomers in dry conditions is essential for sealing applications, as dry contact may occur even in lubricated conditions due to local dewetting. In recent decades, Persson and co-authors have developed a comprehensive theory for rubber contact mechanics and [...] Read more.

Understanding the tribological behavior of elastomers in dry conditions is essential for sealing applications, as dry contact may occur even in lubricated conditions due to local dewetting. In recent decades, Persson and co-authors have developed a comprehensive theory for rubber contact mechanics and dry friction. In this work, their model is implemented and extended, particularly by including static friction based on the bond population model by Juvekar and coworkers. Validation experiments are performed using a tribometer over a wide range of materials, temperatures and speeds. It is shown that the friction model presented in this work can predict the static and dynamic dry friction of various commercial rubber materials with different base polymers (FKM, EPDM and NBR) with an average accuracy of 10%. The model is then used to study the relevance of different elastomer friction contributions under various operating conditions and for different roughness of the counter surface. The present model will help in the development of novel optimized sealing solutions and provide a foundation for future modeling of lubricated elastomer friction. Full article

(This article belongs to the Special Issue Tribology in Germany: Latest Research and Development)

► Show Figures

Figure 1

17 pages, 7505 KiB

Open AccessArticle

Effect of Hydrogen Pressure on the Fretting Behavior of Rubber Materials

by Géraldine Theiler, Natalia Cano Murillo and Andreas Hausberger

Lubricants 2024, 12(7), 233; https://doi.org/10.3390/lubricants12070233 - 23 Jun 2024

Viewed by 870

Abstract

Safety and reliability are the major challenges to face for the development and acceptance of hydrogen technology. It is therefore crucial to deeply study material compatibility, in particular for tribological components that are directly in contact with hydrogen. Some of the most critical [...] Read more.

Safety and reliability are the major challenges to face for the development and acceptance of hydrogen technology. It is therefore crucial to deeply study material compatibility, in particular for tribological components that are directly in contact with hydrogen. Some of the most critical parts are sealing materials that need increased safety requirements. In this study, the fretting behavior of several elastomer materials were evaluated against 316L stainless steel in an air and hydrogen environment up to 10 MPa. Several grades of cross-linked hydrogenated acrylonitrile butadiene (HNBR), acrylonitrile butadiene (NBR) and ethylene propylene diene monomer rubbers (EPDM) were investigated. Furthermore, aging experiments were conducted for 7 days under static conditions in 100 MPa of hydrogen followed by rapid gas decompression. Fretting tests revealed that the wear of these compounds is significantly affected by the hydrogen environment compared to air, especially with NBR grades. After the aging experiment, the friction response of the HNBR grades is characterized by increased adhesion due to elastic deformation, leading to partial slip. Full article

(This article belongs to the Special Issue Tribology in Germany: Latest Research and Development)

► Show Figures

Figure 1

15 pages, 13938 KiB

Open AccessArticle

Effect of Harmful Bearing Currents on the Service Life of Rolling Bearings: From Experimental Investigations to a Predictive Model

by Volker Schneider, Marius Krewer, Gerhard Poll and Max Marian

Lubricants 2024, 12(7), 230; https://doi.org/10.3390/lubricants12070230 - 21 Jun 2024

Viewed by 850

Abstract

This study investigates the effects of harmful bearing currents on the service life of rolling bearings and introduces a model to predict service life as a function of surface roughness. Harmful bearing currents, resulting from electrical discharges, can cause significant surface damage, reducing [...] Read more.

This study investigates the effects of harmful bearing currents on the service life of rolling bearings and introduces a model to predict service life as a function of surface roughness. Harmful bearing currents, resulting from electrical discharges, can cause significant surface damage, reducing the operational lifespan of bearings. This study involves comprehensive experiments to quantify the extent of electrical stress caused by these currents. For this purpose, four series of tests with different electrical stress levels were carried out and the results of their service lives were compared with each other. Additionally, a novel model to correlate the service life of rolling bearings with varying degrees of surface roughness caused by electrical discharges was developed. The basis is the internationally recognized method of DIN ISO 281, which was extended in the context of this study. The findings show that the surface roughness continues to increase as the electrical load increases. In theory, this in turn leads to a deterioration in lubrication conditions and a reduction in service life. Full article

(This article belongs to the Special Issue Tribology in Germany: Latest Research and Development)

► Show Figures

Figure 1

18 pages, 13638 KiB

Open AccessArticle

Ice-versus-Steel Friction: An Advanced Numerical Approach for Competitive Winter Sports Applications

by Birthe Grzemba and Roman Pohrt

Lubricants 2024, 12(6), 203; https://doi.org/10.3390/lubricants12060203 - 4 Jun 2024

Viewed by 592

Abstract

Understanding and predicting the friction between a steel runner and an ice surface is paramount for many winter sports disciplines such as luge, bobsleigh, skeleton, and speed skating. A widely used numerical model for the analysis of the tribological system steel-on-ice is the [...] Read more.

Understanding and predicting the friction between a steel runner and an ice surface is paramount for many winter sports disciplines such as luge, bobsleigh, skeleton, and speed skating. A widely used numerical model for the analysis of the tribological system steel-on-ice is the Friction Algorithm using Skate Thermohydrodynamics (F.A.S.T.), which was originally introduced in 2007 and later extended. It aims to predict the resulting coefficient of friction (COF) from the two contributions of ice plowing and viscous drag. We explore the limitations of the existing F.A.S.T. model and extend the model to improve its applicability to winter sports disciplines. This includes generalizing the geometry of the runner as well as the curvature of the ice surface. The free rotational mechanical mounting of the runner to the moving sports equipment is introduced and implemented. We apply the new model to real-world geometries and kinematics of speed skating blades and bobsleigh runners to determine the resulting COF for a range of parameters, including geometry, temperature, load, and speed. The findings are compared to rule-of-thumb testimonies from athletes, previous numerical approaches, and published experimental results where applicable. While the general trends are reproduced, some discrepancy is found, which we ascribe to the specific assumptions around the formation of the liquid water layer derived from melted ice. Full article

(This article belongs to the Special Issue Tribology in Germany: Latest Research and Development)

► Show Figures

Figure 1

15 pages, 9523 KiB

Open AccessArticle

Tribological Behavior of Hydrocarbons in Rolling Contact

by Daniel Merk, Thomas Koenig, Janine Fritz and Joerg W. H. Franke

Lubricants 2024, 12(6), 201; https://doi.org/10.3390/lubricants12060201 - 3 Jun 2024

Viewed by 491

Abstract

In the analysis of tribological contacts, the focus is often on a singular question or result. However, this entails the potential risk that the overall picture and the relationships could be oversimplified or even that wrong conclusions could be drawn. In this article, [...] Read more.

In the analysis of tribological contacts, the focus is often on a singular question or result. However, this entails the potential risk that the overall picture and the relationships could be oversimplified or even that wrong conclusions could be drawn. In this article, a comprehensive consideration of test results including component and lubricant analyses is demonstrated by using the example of rolling contact. For this purpose, thrust cylindrical roller bearings of type 81212 with unadditized base oils were tested in the mixed-friction area. Our study shows that by using an adapted and innovative surface analysis, a deeper dive into the tribo-film is feasible even without highly sophisticated analytical equipment. The characterization of the layers was performed by the three less time-consuming spatially resolved analysis methods of µXRF, ATR FTIR microscopy and Raman spectroscopy adapted by Schaeffler. This represents a bridge between industry and research. The investigations show that especially undocumented and uncontrolled contamination of the test equipment could lead to surprising findings, which would result in the wrong conclusions. Simple substances, like hydrocarbons, are demanding test specimens. Full article

(This article belongs to the Special Issue Tribology in Germany: Latest Research and Development)

► Show Figures

Figure 1

20 pages, 5635 KiB

Open AccessArticle

Practical Evaluation of Ionic Liquids for Application as Lubricants in Cleanrooms and under Vacuum Conditions

by Andreas Keller, Knud-Ole Karlson, Markus Grebe, Fabian Schüler, Christian Goehringer and Alexander Epp

Lubricants 2024, 12(6), 194; https://doi.org/10.3390/lubricants12060194 - 28 May 2024

Viewed by 493

Abstract

As part of a publicly funded cooperation project, novel high-performance lubricants (oils, greases, assembly pastes) based on ionic liquids and with the addition of specific micro- or nanoparticles are to be developed, which are adapted in their formulation for use in applications where [...] Read more.

As part of a publicly funded cooperation project, novel high-performance lubricants (oils, greases, assembly pastes) based on ionic liquids and with the addition of specific micro- or nanoparticles are to be developed, which are adapted in their formulation for use in applications where their negligible vapor pressure plays an important role. These lubricants are urgently needed for applications in cleanrooms and high vacuum (e.g., pharmaceuticals, aerospace, chip manufacturing), especially when the frequently used perfluoropolyethers (PFPE) are no longer available due to a potential restriction of per- and polyfluoroalkyl substances (PFAS) due to European chemical legislation. Until now, there has been a lack of suitable laboratory testing technology to develop such innovative lubricants for extreme niche applications economically. There is a large gap in the tribological test chain between model testing, for example in the so-called spiral orbit tribometer (SOT) or ball-on-disk test in a high-frequency, linear-oscillation test machine (SRV-Tribometer from German “Schwing-Reib-Verschleiß-Tribometer”), and overall component testing at major space agencies (ESA—European Space Agency, NASA—National Aeronautics and Space Administration) or their service providers like the European Space Tribology Laboratory (ESTL) in Manchester. A further aim of the project was therefore to develop an application-orientated and economical testing methodology and testing technology for the scientifically precise evaluation and verifiability of the effect of ionic liquids on tribological systems in cleanrooms and under high vacuum conditions. The newly developed test rig is the focus of this publication. It forms the basis for all further investigations. Full article

(This article belongs to the Special Issue Tribology in Germany: Latest Research and Development)

► Show Figures

Graphical abstract

12 pages, 2876 KiB

Open AccessArticle

Improved Tribological Performance of a Polybutylene Terephthalate Hybrid Composite by Adding a Siloxane-Based Internal Lubricant

by Shengqin Zhao, Rolf Merz, Stefan Emrich, Johannes L’huillier and Leyu Lin

Lubricants 2024, 12(6), 189; https://doi.org/10.3390/lubricants12060189 - 28 May 2024

Viewed by 553

Abstract

To mitigate the environmental hazards aroused by fossil-based lubricants, the development of eco-friendly internal lubricants is imperative. Siloxane-based internal lubricants, widely applied as plasticizers in polymeric compounds, are a promising option. However, their impacts on the tribological properties of polymeric tribocomponents are still [...] Read more.

To mitigate the environmental hazards aroused by fossil-based lubricants, the development of eco-friendly internal lubricants is imperative. Siloxane-based internal lubricants, widely applied as plasticizers in polymeric compounds, are a promising option. However, their impacts on the tribological properties of polymeric tribocomponents are still unclarified. Therefore, in the current study, a siloxane-based internal lubricant with the product name ‘EverGlide MB 1550 (EG)’ was dispersed into a polybutylene terephthalate (PBT)-based tribological composite to investigate whether the tribological properties of the composite can be optimized. A block-on-ring (BOR) test configuration was used for this purpose. It was found that the addition of EG to the composite significantly improved the tribological behavior; the improvement was particularly significant under lower load conditions (pv-product ≤ 2 MPa∙m/s). Compared to the reference PBT composite, the addition of EG reduced the friction coefficient (COF) by about 30% and the specific wear rate by about 14%. An accompanying surface analytical investigation using photoelectron spectroscopy to elucidate the effective mechanisms at the molecular level showed the availability of tribologically effective and free EG after its addition to the composite in the relevant tribocontact. Full article

(This article belongs to the Special Issue Tribology in Germany: Latest Research and Development)

► Show Figures

Figure 1

17 pages, 3126 KiB

Open AccessArticle

Transition between Friction Modes in Adhesive Contacts of a Hard Indenter and a Soft Elastomer: An Experiment

by Iakov A. Lyashenko, Thao H. Pham and Valentin L. Popov

Lubricants 2024, 12(4), 110; https://doi.org/10.3390/lubricants12040110 - 28 Mar 2024

Viewed by 2763

Abstract

The tangential adhesive contact (friction) between a rigid steel indenter and a soft elastomer at shallow indentation depths, where the contact exists mainly due to adhesion, is investigated experimentally. The dependencies of friction force, contact area, average tangential stresses, and the coordinates of [...] Read more.

The tangential adhesive contact (friction) between a rigid steel indenter and a soft elastomer at shallow indentation depths, where the contact exists mainly due to adhesion, is investigated experimentally. The dependencies of friction force, contact area, average tangential stresses, and the coordinates of the front and back edges of the contact boundary on the indenter displacement are studied. It is found that first a stick–slip mode of friction is established, which is then replaced by another, more complex mode where the phase of a global slip of the elastomer on the indenter surface is absent. In both regimes, the evolutions of friction force and contact area are analyzed in detail. Full article

(This article belongs to the Special Issue Tribology in Germany: Latest Research and Development)

► Show Figures

Figure 1

15 pages, 13289 KiB

Open AccessArticle

Calculation and Validation of Planet Gear Sliding Bearings for a Three-Stage Wind Turbine Gearbox

by Huanhuan Ding, Ümit Mermertas, Thomas Hagemann and Hubert Schwarze

Lubricants 2024, 12(3), 95; https://doi.org/10.3390/lubricants12030095 - 15 Mar 2024

Viewed by 1511

Abstract

In recent years, the trend towards larger wind turbines and higher power densities has led to increasing demands on planet gear bearings. The use of sliding bearings instead of rolling bearings in planetary bearings makes it possible to increase the power density with [...] Read more.

In recent years, the trend towards larger wind turbines and higher power densities has led to increasing demands on planet gear bearings. The use of sliding bearings instead of rolling bearings in planetary bearings makes it possible to increase the power density with lower component costs and higher reliability. Therefore, the use of planet gear sliding bearings in wind turbine gearboxes has become more common. However, the flexible structure and complex load conditions from the helical tooth meshes lead to highly complex elastic structure deformation that modifies the lubricant film thickness and pressure distribution and, thus, has to be considered in the calculation of the bearing’s load-carrying capacity. This paper introduces a highly time-efficient calculation procedure that is validated with pressure measurement data from a three-stage planetary gearbox for a multi-megawatt wind energy plant. The investigations focus on three main objectives: (i) analyses of experimental and predicted results for different load cases, (ii) validation of the results of planet gear sliding bearing code, and (iii) discussion on mandatory modeling depths for the different planet stages. Results indicate the necessity of further research in this field of applications, particularly for the third-stage bearings. Full article

(This article belongs to the Special Issue Tribology in Germany: Latest Research and Development)

► Show Figures

Figure 1

Journal Menu

Journal Browser

Tribology in Germany: Latest Research and Development

Share This Special Issue

Special Issue Editor

Special Issue Information

Keywords

Published Papers (12 papers)

Research

Further Information

Guidelines

MDPI Initiatives

Follow MDPI