Search Results (778)

The complete anodic oxidation of ammonia is an important part of direct ammonia fuel cells. Fabricating a high-performance electrocatalyst for ammonia oxidation reaction is meaningful for developing a direct ammonia fuel cell. Herein, we designed one platinum-decorated NiCo-layered double hydroxide nanoflower on Ni foam (Pt-NiCo-LDH-Ni foam) and measured the electrocatalytic performance via the cyclic voltammetry (CV) technique. The experimental results demonstrated that the optimized Pt-NiCo-LDH-Ni foam showed great electrocatalytic performance, with a low overpotential with a value of −0.573 V, a high current density of 17.75 mA cm⁻² for the ammonia oxidation reaction, and good stability. Full article

This study presents a vanadate-exchanged Zn-Al layered double hydroxide (LDH) coating on a ZX21 Mg alloy (Mg-2.15 wt%Zn-0.97 wt%Ca) by electrodeposition and immersion anion-exchange post-treatment. With the prepared vanadate-exchanged electrodeposited Zn-Al LDH coating, the corrosion resistance of the ZX21 Mg alloy improves with a decrease in the corrosion current density from 62.4 μA/cm² to 3.32 μA/cm². The fabricated vanadate-exchanged electrodeposited Zn-Al LDH coating contains complex anions in the interlayers, including mainly nitrate (NO₃⁻), carbonate (CO₃²⁻), and different vanadates. The coating not only serves as a physical barrier on the ZX21 Mg alloy but also absorbs chloride ions in the environment through anion exchange and inhibits corrosion with the reduction of the interlayer vanadates. Furthermore, the vanadates can also be released into the damaged area of the coating. Full article

In the context of waters polluted with different high-risk contaminants, the development of efficient materials able to efficiently clean them is necessary. In the first part, the present review focuses on the ability of various types of magnetic layered double hydroxide materials to act as adsorbents for water contaminated mainly with heavy metals and dyes. Also, this paper reviews the ability of different magnetic layered double hydroxide materials to act as potential adsorbents for the treatment of wastewater contaminated with other types of pollutants, such as pharmaceutical products, phenolic compounds, phytohormones, and fungicides. In the second part, the applicability of the catalytic method for water depollution is explored. Thus, the use of simple or composite materials based on Fe₃O₄ is reviewed for the purpose of the catalytic degradation of organic compounds (dyes/phenols/pharmaceuticals). At the end, a review of multifunctional materials able to simultaneously neutralize different types of pollutants from wastewater is provided. Full article

The design of an antimicrobial coating material has become important in the prevention of infections caused by the transmission of pathogens coming from human contact with contaminated surfaces. With that aim, layered single hydroxides (LSHs) and layered double hydroxides (LDHs) containing Zn and Cu intercalated with antimicrobial molecules were synthesized and characterized. Cinnamate and salicylate anions were chosen because of their well-known antimicrobial activity. Several coatings based on polyvinyl alcohol (PVA) and LDHs or LSHs with increasing amounts of filler were prepared and filmed on a polyethylene terephthalate (PET) substrate. The coatings were characterized, and their antimicrobial activity was evaluated against several pathogens that are critical in nosocomial infections, showing a synergistic effect between metal ions and active molecules and the ability to inhibit their growth. Full article

This article presents the results of research on the growth kinetics, microstructure (SEM/EDS/XRD), and corrosion behavior of Zn-5Al coatings obtained using a high-temperature hot dip process on B500B reinforcing steel. The corrosion resistance of the coatings was determined using the neutral salt spray (NSS) test (EN ISO 9227). Based on chemical composition tests in micro-areas (EDS) and phase composition tests (XRD), corrosion products formed on the coating surface after exposure to a corrosive environment containing chlorides were identified. In the outer layer of the coating, areas rich in Zn and Al were found, which were solid solutions of Al in Zn (α), while the diffusion layer was formed by a layer of Fe(Al,Zn)₃ intermetallics. The growth kinetics of the coatings indicate the sequential growth of the diffusion layer, controlled by diffusion in the initial phase of growth, and the formation of a periodic layered structure with a longer immersion time. The NSS test showed an improved corrosion resistance of reinforcing bars with Zn-5Al coatings compared to a conventional hot-dip-galvanized zinc coating. The increase in corrosion resistance was caused by the formation of beneficial corrosion products: layered double hydroxides (LDH) based on Zn²⁺ and Al³⁺ cations and Cl⁻ anions and simonkolleite—Zn₅(OH)₈Cl₂·H₂O. Full article

Indomethacin (INDO) has a mechanism of action based on inhibiting fatty acids cyclooxygenase activity within the inflammation process. The action mechanism could be correlated with possible anticancer activity, but its high toxicity in normal tissues has made therapy difficult. By the coprecipitation method, the drug carried in a layered double hydroxides (LDH) hybrid matrix would reduce its undesired effects by promoting chemotherapeutic redirection. Therefore, different samples containing INDO intercalated in LDH were synthesized at temperatures of 50, 70, and 90 °C and synthesis times of 8, 16, 24, and 48 h, seeking the best structural organization. X-ray diffraction (XRD), vibrational Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), spectrophotometric analysis in UV-VIS, and differential thermogravimetric analysis (TGA/DTA) were used for characterization. Our results indicate that higher temperatures and longer synthesis time through coprecipitation reduce the possibility of INDO intercalation. However, it was possible to establish a time of 16 h and a temperature of 50 °C as the best conditions for intercalation. In vitro results confirmed the cell viability potential and anticancer activity in the LDH-INDO sample (16 h and 50 °C) for gastric cancer (AGP01, ACP02, and ACP03), breast cancer (MDA-MB-231 and MCF-7), melanoma (SK-MEL-19), lung fibroblast (MRC-5), and non-neoplastic gastric tissue (MN01) by MTT assay. Cell proliferation was inhibited, demonstrating higher and lower toxicity against MDA-MB-231 and SK-MEL-19. Thus, a clinical redirection of INDO is suggested as an integral and adjunctive anticancer medication in chemotherapy treatment. Full article

The proposed study is devoted to highlighting the importance of mixed oxides preparation through the layered double hydroxide route for undesirable gas pollutants abatement. Different series of Cu/Al/Ce mixed oxides with similar or different stoichiometrics were prepared and compared for toluene and/or CO oxidation. Catalyst synthesis methods influence material properties and activity for oxidation reactions. The high activity for the oxidation reactions of mixed oxides derived from LDH is explained by the Cu/Ce synergy. The presence of CO in the CO/toluene mixture does not affect the total toluene oxidation, and the toluene does not affect the total oxidation of CO conversion at low temperatures. The most effective catalytic material (Cu₆Al_1.2Ce_0.8) presents a long lifetime stability for total toluene oxidation and resistance to CO poisoning in mixtures. Full article

CO-selective methanation (CO-SMET) is an efficient hydrogen-rich (H₂-rich) gas purification technology for proton exchange membrane fuel cells. It is vital to develop suitable catalysts with good low-temperature activity for CO-SMET reactions. In this study, RuNi/TiZr_x-mixed metal oxide (RuNi/TiZr_x-MMO) catalysts with different molar ratios of Zr/Ti, derived from a Zr-promoted NiTi-layered double hydroxide (NiTi-LDH) precursor were successfully prepared using the co-precipitation and wet impregnation methods. The RuNi/TiZr_0.2-MMO catalyst possesses higher catalytic performance in a lower temperature window of 180–280 °C, which can reduce the CO concentration to be below 10 ppm. The characterization results obtained from XRD, BET, SEM, TEM, XPS, TPR, and TPD suggest that the addition of ZrO₂ increases the surface area of the catalyst, improves the dispersion of metallic nanoparticles, increases the reducibility of Ni species on the RuNi/TiZr_0.2-MMO catalyst’s surface, and enhances the adsorption and activation ability of CO, resulting in remarkable catalytic performance at lower reaction temperatures. Moreover, the RuNi/TiZr_0.2-MMO catalyst demonstrated long-term catalytic stability and carbon resistance. Full article

This study presents a promising method for creating high-performance supercapacitor electrodes. The approach involves crafting a unique composite material—nickel-cobalt-layered double hydroxides (NiCo-LDH) grown on carbon nanoballs (CNBs). This is achieved by first creating a special carbon material rich in oxygen and nitrogen from a polybenzoxazine source. At first, eugenol, ethylene diamine and paraformaldehyde undergo Mannich condensation to form the benzoxazine monomer, which undergoes self-polymerization in the presence of heat to produce polybenzoxazine. This was then carbonized and activated to produce CNBs containing heteroatoms. Then, through a hydrothermal technique, NiCo-LDH nanocages are directly deposited onto the CNBs, eliminating the need for complicated templates. The amount of CNBs used plays a crucial role in performance. By optimizing the CNB content to 50%, a remarkable specific capacitance of 1220 F g⁻¹ was achieved, along with excellent rate capability and impressive cycling stability, retaining 86% of its capacitance after 5000 cycles. Furthermore, this NiCo-LDH/CNB composite, when combined with active carbon in a supercapacitor configuration, delivered outstanding overall performance. The exceptional properties of this composite, combined with its simple and scalable synthesis process, position it as a strong contender for next-generation sustainable energy storage devices. The ease of fabrication also opens doors for its practical application in advancing energy storage technologies. Full article

Water pollution has become a great challenge today. To address this problem regarding wastewater treatment by removing toxic synthetic dyes from wastewater, this research focused on the synthesis of a novel starch-modified NiCrMn-layered double hydroxide composite through the coprecipitation method and applied it as a photocatalyst for the degradation of reactive orange 13 dye. The synthesized photocatalyst was characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), point of zero charges (PZC), dynamic light scattering (DLS), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and Zeta potential techniques. These techniques revealed different characteristics of photocatalysts, like surface and structural properties. According to BET analysis, the final composite had 2.5 × 10² m²/g BET-specific surface area with a 45.56 nm pore radius value, and the overall composite found as mesoporous. Similarly, in DLS analysis, bare NiCrMn-LDH had 404 nm hydrodynamic size, which increased for the final starch composite up to 667 nm. Zeta potential value changed from −14.56 mV to 0.95 mV after the incorporation of starch with NiCrMn-LDH. They confirmed the incorporation of starch with trimetallic NiCrMn-layered double hydroxide (2:1:2). Starch association improved the properties of the photocatalyst like surface area. Different parameters like pH value, initial dye concentration, photocatalyst dose, hydrogen peroxide concentration, effect of sacrificial reagent, and effect of inorganic anions were studied for degradation of RO13. Overall, the photocatalysis process for RO13 followed pseudo-first-order kinetics. Photocatalytic degradation reactions for reactive orange 13 were conducted with an initial dye concentration of 10 mg/L, photocatalyst dosage of 20 mg/50 mL, and pH value at 3 in the presence of sunlight, resulting in an impressive degradation removal rate of 86.68%. This remarkable degradation ability of the photocatalyst for reactive orange 13 proves this composite was highly efficient. Full article

Acid–base M²⁺MgAlO and M²⁺AlO mixed oxides (where M²⁺ = Mg, Cu, Co, Zn, and Ni) were obtained by thermal decomposition of the corresponding layered double hydroxide (LDH) precursors and used as catalysts for cyclohexanol and benzaldehyde condensation under solvent-free conditions. The catalysts were characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy (SEM), and temperature-programmed desorption of CO₂ (TPD-CO₂). Gas chromatography–mass spectroscopy (GC/MS) was used for the identification and quantification of the product mixtures. In the reaction of cyclohexanol and benzaldehyde on M²⁺MgAlO and MgAlO catalysts, a 2,6-dibenzylidene-cyclohexanone was obtained as the main product as a result of consecutive one-pot dehydrogenation of cyclohexanol to cyclohexanone and subsequent Claisen–Schmidt condensation. In the reaction mixture obtained in the presence of NiAlO, CoAlO, and ZnAlO catalysts, a cyclohexyl ester of 6-hydroxyhexanoic acid was detected together with the main product. This is most likely a by-product obtained after the oxidation, ring opening, and subsequent esterification of the cyclohexanol. Full article

Sulfide organics and phenols are ubiquitous in freshwater lakes all over the world. As two taste and odor (T and O) compounds, they are harmful to the environment and human body. The existing detection methods for T and O compounds mainly include sensory analysis and gas-phase mass spectrometry, which are cumbersome and time-consuming. Herein, a method for the simultaneous and rapid detection of two T and O compounds (methyl sulfide and 2,4-di-tert-butylphenol) based on surface-enhanced Raman spectroscopy (SERS) is firstly developed. The SERS substrate was prepared by coating Ag nanoparticles (Ag NPs), layered double hydroxide (LDH), and graphene oxide (GO) on the surface of an Ag-coated Au nanoparticle (Au@Ag NP) substrate. Under optimal conditions, this SERS substrate possessed low detection limits of 1.53 ppm for methyl sulfide and 0.39 ppm for 2,4-di-tert-butylphenol. In addition, it took only 20 min to complete the detection using this method, without complex sample pretreatment. Furthermore, it was successfully applied to simultaneously detect methyl sulfide and 2,4-di-tert-butylphenol in actual water samples and had good application prospects for the rapid detection of T and O compounds in water. Full article

Heavy metals and organic pollutants are prevalent in water bodies, causing great damage to the environment and human beings. Hence, it is urgent to develop a kind of adsorbent with good performance. Anion interlacing layered double hydroxides (LDHs) are a promising adsorbent for the sustainable removal of heavy metal ions and dyes from wastewater. Using aluminum chloride, zinc chloride and ammonium pentaborate tetrahydrate (NH₄B₅O₈ · 4H₂O, BA) as raw materials, the LDHs complex (BA-LDHs) of B₅O₈⁻ intercalation was prepared by one-step hydrothermal method. The BA-LDHs samples were characterized by a X-ray powder diffractometer (XRD), scanning electron microscope (SEM), Fourier transform infrared spectrometer (FT-IR) and the Brunauer–Emmett–Teller (BET) method. The results showed that B₅O₈^- was successfully intercalated. Adsorption experimental results suggested that BA-LDHs possess a maximum adsorption capacity of 18.7, 57.5, 70.2, and 3.12 mg·g⁻¹ for Cd(II), Cu(II), Cr(VI) and Methylene blue (MB) at C_s = 2 g·L⁻¹, respectively. The adsorption experiment conforms to the Langmuir and Freundlich adsorption models, and the kinetic adsorption data are well fitted by the pseudo-second-order adsorption kinetic equation. The as-prepared BA-LDHs have potential application prospects in the removal of heavy metals and dyes in wastewater. More importantly, they also provide a strategy for preparing selective adsorbents. Full article

In this study, copper (Cu)- and manganese (Mn)-based layered double hydroxide (LDH) nanosheets were produced by modest and low-cost hydrothermal technique to display an improved photocatalytic performance toward the degradation of aqueous methylene blue (MB). The morphological and structural properties of the as-prepared photocatalysts were characterized through various techniques comprising XRD, FT-IR, SEM, EDS, and their MB degradation activity was evaluated under visible light irradiation. SEM results explore that the synthesized LDH materials have a sheet-like morphology and are stacked layer by layer. Various analysis parameters, such as the effect of the contact time, concentration and pH of MB solutions were performed to optimize the performance of fabricated LDH materials. The results revealed that the as-synthesized CuAl-LDH and MnAl-LDH exhibited a 74.95 and 70.93% removal of MB under solar light within 180 min. Moreover, synthesized photocatalysts showed an excellent performance of up to four regeneration cycles. We believe that this study provides novel mechanistic insights into the design and preparation of highly competent photocatalysts using low-cost materials, with applications in environmental remediation. Full article

The increasing discharge of antibiotic wastewater leads to increasing water pollution. Most of these antibiotic wastewaters are persistent, strongly carcinogenic, easy to bioaccumulate, and have other similar characteristics, seriously jeopardizing human health and the ecological environment. As a commonly used wastewater treatment technology, non-homogeneous electro-Fenton technology avoids the hazards of H₂O₂ storage and transportation as well as the loss of desorption and reabsorption. It also facilitates electron transfer on the electrodes and the reduction of Fe³⁺ on the catalysts, thereby reducing sludge production. However, the low selectivity and poor activity of electro-synthesized H₂O₂, along with the low concentration of its products, combined with the insufficient activity of electrically activated H₂O₂, results in a low ∙OH yield. To address the above problems, composites of layered bimetallic hydroxides and carbon materials were designed and prepared in this paper to enhance the performance of electro-synthesized H₂O₂ and non-homogeneous electro-Fenton by changing the composite mode of the materials. Three composites, NiFe layered double hydroxides (LDHs)/reduced graphene oxide (rGO), NiMn LDHs/rGO, and NiMnFe LDHs/rGO, were constructed by the electrostatic self-assembly of exfoliated LDHs with few-layer graphene. The LDHs/rGO was loaded on carbon mats to construct the electro-Fenton cathode materials, and the non-homogeneous electro-Fenton oxidative degradation of organic pollutants was realized by the in situ electrocatalytic reduction of O₂ to ∙OH. Meanwhile, the effects of solution pH, applied voltage, and initial concentration on the performance of non-homogeneous electro-Fenton were investigated with ceftazidime as the target pollutant, which proved that the cathode materials have an excellent electro-Fenton degradation effect. Full article