Search Results (1,367)

Alcohol’s detrimental effects on bone health are well established, yet some literature suggests moderate consumption may offer benefits. With alcohol use on the rise, we investigate the impact of acute and chronic alcohol administration, along with withdrawal, on male Wistar rat femurs. We observed a transient cortical thickness increase with acute alcohol (AA) compared to chronic exposure (CA) but no significant changes in trabecular parameters or mechanical properties. High osteocalcin and osteopontin expression levels were noted in AA, alongside elevated RANKL expression. Conversely, CA showed low TRAP levels. FGF23 expression significantly increased during alcohol withdrawal (AW), while GPX decreased after chronic exposure but rose during withdrawal. Although mechanical strength changes were insignificant, biochemical shifts suggest alcohol exposure promotes bone resorption, reduces antioxidant protection, and potentially hampers active vitamin D and phosphate reabsorption via FGF23 upregulation. Full article

A sophisticated characterisation of a porous material structure has been challenging in material science. Three-dimensional (3D) structure analysis allows the evaluation of a material’s homogeneity, pore size distribution and pore wall properties. Micro-computed tomography (micro-CT) offers a non-destructive test method for material evaluation. This paper characterises a novel ternary binder’s porous structure using micro-CT. Gypsum–cement–pozzolan (GCP) ternary binders are low-carbon footprint binders. Both natural and industrial gypsum were evaluated as a major components of GCP binders. Porous GCP binder was obtained by a foaming admixture, and the bulk density of the material characterised ranged from 387 to 700 kg/m³. Micro-CT results indicate that pores in the range from 0.017 to 3.0 mm can be effectively detected and described for porous GCP binders. The GCP binder structure proved to be dominant by 0.1 to 0.2 mm micropores. For GCP binders produced with natural gypsum, macropores from 2.2 to 2.9 mm are formed, while GCP binders with phosphogypsum possess pores from 0.2 to 0.6 mm. Micro-CT proved to be an effective instrument for characterising the homogeneity and hierarchical pore structure of porous ternary binders. Full article

After polymer flooding, the heterogeneity between different layers intensifies, forming intricate seepage channels and fluid diversions, which results in decreased circulation efficiency and lower recovery rates, leaving a significant amount of residual oil trapped within the reservoir. Understanding the characteristics of residual oil occurrence is crucial for enhancing oil recovery post-polymer flooding. This study focused on sandstone reservoirs with varying permeability in the Saertu block of the Daqing oilfield. Using cryosectioning and laser scanning confocal microscopy, the occurrence characteristics of the residual oil in these sandstone reservoirs post-polymer flooding were investigated. Additionally, micro-CT and scanning electron microscopy were employed to analyze the impact of the pore structure on the distribution characteristics of the residual oil. The results indicate that laser scanning confocal images reveal that post-polymer flooding, the residual oil in high- and low-permeability sandstone reservoirs predominantly exists in a bound state (average > 47%), mostly as particle-adsorbed oil. In contrast, the residual oil in medium-permeability reservoirs is primarily in a free state (average > 49%), mostly as intergranular-adsorbed oil. In high-permeability sandstone reservoirs, heavy oil components are mainly in a particle-adsorbed form; in medium-permeability sandstone reservoirs, residual oil predominantly consists of heavy components, with most light components occurring in a clustered form; in low-permeability sandstone reservoirs, clustered residual oil exists in a balanced coexistence of light and heavy components, while the heavy components primarily exist in a particle-adsorbed form. Post-polymer flooding, the large pore–throat structure in high-permeability sandstone reservoirs results in effective displacement and less free residual oil; medium-permeability sandstone reservoirs, with medium–large pores and throats, have preferential channels and fine particles blocking the throats, leading to some unswept pores and more free residual oil; low-permeability sandstone reservoirs, with small pores and throats, exhibit weak displacement forces and poor mobility, resulting in more bound residual oil. The distribution and content of clay particles and clay minerals, along with the complex microscopic pore structure, are the main factors causing the differences in the residual oil occurrence states in sandstones with varying permeability. Full article

Carbon fiber reinforced polymer (CFRP) composites are renowned for their exceptional mechanical properties, with applications in industries such as automotive, aerospace, medical, civil, and beyond. Despite these merits, a significant challenge in CFRPs lies in their repairability and maintenance. This study, for the first time, delves into the processing and self-healing capability of aromatic thermosetting co-polyester vitrimer-based carbon fiber composites through mechanical testing. Vitrimers are an emerging class of thermosetting polymers, which, owing to their exchangeable covalent bonds, enable the re-formation of bonds across cracks. The specific vitrimer chosen for this study is an aromatic thermosetting co-polyester (ATSP). The mechanical properties of samples were analyzed initially through three-point bending (3PB) testing at room temperature before and after healing (by curing samples for 2 h at 280 °C). Samples were also 3PB tested at 100 °C to analyze their mechanical properties at an elevated temperature for comparison to the samples tested at room temperature. To investigate the fracture properties, optical microscopy images of samples were taken after 3PB tests, which were analyzed to observe crack initiation and crack growth behavior. Through load–displacement curves from double cantilever beam (DCB) mechanical testing, the Mode I crack initiation fracture toughness values of self-healed composites and control composites were calculated to evaluate healing efficiency in ATSP CFRP composites cured at 280 °C for 2 h. Scanning electron microscopy (SEM) showed a similar surface morphology of cracks before and after self-healing. Micro-computed tomography (CT) X-ray imaging confirmed that the healed samples closely resembled the as-fabricated ones, with the exception of some manufacturing voids, caused by outgassing in the initial healing cycle. This research demonstrated the ability for the in situ repair of ATSP CFRPs by restoring the fracture toughness to values comparable to the pristine composite (~289 J/m²). Full article

The purpose of this study was to evaluate potential osteoarthritic alterations within the ankle using a surgically-induced chronic lateral ankle instability (CLAI) model. Twelve rats were assigned randomly to either the control (n = 4) or CLAI group (n = 8). Surgery was performed on the right ankle. Osteoarthritis was assessed through in-vivo micro-CT at 8 weeks and a clinical analysis. Macroscopic analysis, high-resolution ex-vivo micro-CT and histological examination were conducted after euthanasia at 12 weeks. Three subgroups (SG) were analyzed. SG1 comprised the operated ankles of the CLAI group (n = 8). SG2 consisted of the non-operated ankles of the CLAI group (n = 8). SG3 included both sides of the control group (n = 8). In-vivo micro-CT revealed no significant differences among the three subgroups when analyzed together (p = 0.42), and when comparing SG1 with SG2 (p = 0.23) and SG3 (p = 0.43) individually. No noticeable clinical differences were observed. After euthanasia, macroscopic analysis employing OARSI score, did not demonstrate significant differences, except between the medial tibia of SG1 and SG3 (p = 0.03), and in the total score comparison between these two subgroups (p = 0.015). Ex-vivo micro-CT did not reveal any differences between the three subgroups regarding bony irregularities and BV/TV measurements (SG1 vs. SG2 vs. SG3: p = 0.72; SG1 vs. SG2: p = 0.80; SG1 vs. SG3: p = 0.72). Finally, there was no difference between the three subgroups regarding OARSI histologic score (p = 0.27). These findings indicate that the current model failed to induce significant osteoarthritis. However, they lay the groundwork for improving the model’s effectiveness and expanding its use in CLAI research, aiming to enhance understanding of this pathology and reduce unnecessary animal sacrifice. Full article

Short carbon fiber-reinforced polymer composites are widely used in polymer extrusion additive manufacturing (AM), including large-area additive manufacturing (LAAM), due to their enhanced mechanical properties as compared to neat polymers. However, the mechanical properties of these composites depend on microstructural characteristics, including fibers and micro-voids, which are determined during processing. In this work, the correlation between fibers and micro-voids within the microstructure of LAAM polymer composites throughout various processing stages of short carbon fiber-reinforced acrylonitrile butadiene styrene (SCF/ABS) is investigated. The processing stages considered here include the incoming pellets, a single freely extruded strand, a single regularly deposited bead, and a single regularly deposited bead pressed by a mechanical roller. A high-resolution X-ray micro-computed tomography (µCT) system is employed to characterize the microstructural features in terms of the fibers (volume fraction, fiber orientation tensor) and micro-voids (volume fraction, sphericity) in the SCF/ABS samples. The results indicate that micro-voids exist within the microstructure of the SCF/ABS composite in all four stages considered here and that the micro-void volume fraction and micro-void sphericity vary among the test samples. Moreover, the results show a considerable variation in fiber orientation and fiber volume fraction within the microstructure throughout all the stages considered; however, all the samples show the highest alignment in the extrusion/print direction. Furthermore, a correlation is identified between the fiber orientation and the micro-void volume fraction within samples from all four stages considered here. This finding suggests that fibers tend to align more in the extrusion/print direction in regions with less micro-void content. Full article

In the present work, an innovative range of foams based on flax gum-filled epoxy resin was developed, reinforced or not by flax fibers. Foams and composites with different gum and epoxy resin contents were produced and their mechanical and thermal performances were characterized. To enhance the organic flax gum filler’s cross-linking, we exploited the oxidized components’ reactivity with the amine hardener (isophorone diamine). We compared the materials obtained with those derived from the native components. The flax gum and fibers were primarily characterized by chemical analysis, NMR, and FTIR to evaluate the mild oxidation of the native materials. The formation of chemical bonds between the oxidized polymer chains, epoxy resin, and hardener was evidenced by FTIR, and the materials were then studied by SEM and X-ray computed micro-tomography (CT) and submitted to mechanical and thermal tests. The relevance of the oxidation treatment was highlighted through a significant increase in density and mechanical performance (+36% and +81%, respectively, for the 100% flax gum material). The positive effect of the flax fibers on homogeneity evidenced through micro-CT analysis was also clearly addressed. This set of promising results paves the way for the future development of fully flax-based insulation composite materials. Full article

3D printing technology is becoming a widely adopted alternative to traditional polymer manufacturing methods. The most important advantage of 3D printing over traditional manufacturing methods, such as injection molding or extrusion, is the short time from the creation of a new design to the finished product. Nevertheless, 3D-printed parts generally have lower strength and lower durability compared to the same parts manufactured using traditional methods. Resistance to the environmental conditions in which a 3D-printed part operates is important to its durability. One of the most important factors that reduces durability and degrades the mechanical properties of 3D-printed parts is temperature, especially rapid temperature changes. In the case of inhomogeneous internal geometry and heterogeneous material properties, rapid temperature changes can have a significant impact on the degradation of 3D-printed parts. This degradation is more severe in high-humidity environments. Under these complex service conditions, information on the strength and fatigue behavior of 3D-printed polymers is limited. In this study, we evaluated the effects of high humidity and temperature changes on the durability and strength properties of 3D-printed parts. Samples made of commonly available materials such as ABS (Acrylonitrile Butadiene Styrene), ASA (Acrylonitrile-Styrene-Acrylate), HIPS (High-Impact Polystyrene), and PLA (Poly(lactic acid)) were subjected to temperature cycling, from an ambient temperature to −20 °C, and then were heated to 70 °C. After thermal treatment, the samples were subjected to cyclic loading to determine changes in their fatigue life relative to non-thermally treated reference samples. The results of cyclic testing showed a decrease in durability for samples made of ASA and HIPS. The ABS material proved to be resistant to the environmental effects of shocks, while the PLA material exhibited an increase in durability. Changes in the internal structure and porosity of the specimens under temperature changes were also evaluated using microcomputed tomography (microCT). Temperature changes also affected the porosity of the samples, which varied depending on the material used. Full article

Non-small-cell lung cancer (NSCLC) comprises approximately 85% of all lung cancer cases, often diagnosed at advanced stages, which diminishes the effective treatment options and survival rates. This systematic review assesses the utility of emerging biomarkers—circulating tumor DNA (ctDNA), microRNAs (miRNAs), and the blood tumor mutational burden (bTMB)—enhanced by next-generation sequencing (NGS) to improve the diagnostic accuracy, prognostic evaluation, and treatment strategies in NSCLC. Analyzing data from 37 studies involving 10,332 patients from 2020 to 2024, the review highlights how biomarkers like ctDNA and PD-L1 expression critically inform the selection of personalized therapies, particularly beneficial in the advanced stages of NSCLC. These biomarkers are critical for prognostic assessments and in dynamically adapting treatment plans, where high PD-L1 expression and specific genetic mutations (e.g., ALK fusions, EGFR mutations) significantly guide the use of targeted therapies and immunotherapies. The findings recommend integrating these biomarkers into standardized clinical pathways to maximize their potential in enhancing the treatment precision, ultimately fostering significant advancements in oncology and improving patient outcomes and quality of life. This review substantiates the prognostic and predictive value of these biomarkers and emphasizes the need for ongoing innovation in biomarker research. Full article

This study evaluated the bone incorporation process of a screw-shaped internal fixation device made of poly (L-lactide-co-D, L-lactide) (PLDLLA). Thirty-two male Wistar rats received 32 fixation devices (2 mm × 6 mm) randomly assigned to either the right or left tibia and one implant in each animal. After 7, 14, 28, and 42 days, the rats were euthanized and the specimens were subjected to microtomographic computed tomography (microCT) and histomorphometric analyses to evaluate bone interface contact (BIC%) and new bone formation (NBF%) in cortical and cancellous bone areas. The animals euthanized on days 28 and 42 were treated with calcein and alizarin red, and confocal LASER microscopy was performed to determine the mineral apposition rate (MAR). Micro-CT revealed a higher percentage of bone volume (p < 0.006), trabecular separation (p < 0.001), and BIC in the cortical (p < 0.001) and cancellous (p = 0.003) areas at 28 and 42 days than at 7 and 14 days. The cortical NBF at 42 days was greater than that at 7 and 14 days (p = 0.022). No statistically significant differences were observed in cancellous NBF or MAR at 28 and 42 days. Based on these results, it can be seen that the PLDLLA internal fixation device is biocompatible and allows new bone formation around the screw thread. Full article

Amidst the burgeoning interest in rotating magnetic fields (RMF) within biological research, there remains a notable gap in the scientific evidence concerning the long-term safety of RMF. Thus, this study aimed to investigate the safety of protracted exposure to a 0.2 T, 4 Hz RMF over 10 months in mice. Two-month-old female C57BL/6 mice were randomly allocated to either the RMF group (exposed to 0.2 T, 4 Hz real RMF) or the SHAM group (exposed to 0 T, 4 Hz sham RMF). Throughout the experiment, the murine weekly body weights were recorded, and their behavioral traits were assessed via open field tests. In the final month, a comprehensive evaluation of the murine overall health was conducted, encompassing analyses of blood parameters, histomorphological examination of major organs, and skeletal assessments using X-ray and micro-CT imaging. The murine immune system and lipid metabolism were evaluated through immunochip analysis and metabolomics. Notably, no discernible adverse effects with RMF exposure were observed. Murine body weight, locomotor behavior, organ histomorphology, and skeletal health remained unaffected by RMF. Blood analysis revealed subtle changes in hormone and lipid levels between the SHAM and RMF groups, yet these differences did not reach statistical significance. Moreover, RMF led to elevated serum interleukin-28 (IL-28) levels, albeit within the normal range, and modest alterations in serum lipid metabolites. Conclusively, mice exposed to the 0.2 T, 4 Hz RMF for 10 months displayed no significant signs of chronic toxicity, indicating its potential clinical application as a physical therapy. Full article

In the context of global efforts to transition toward renewable energy and reduce greenhouse gas emissions, geothermal energy is increasingly recognized as a viable and sustainable option. This paper presents a comprehensive assessment derived from a subset of a larger sample collection within the Dunántúli Group of the Pannonian Basin, Hungary, focusing on optimizing micro-computed tomography (µ-CT) resolution for analyzing pore structures in sandstone formations. By categorizing samples based on geological properties and selecting representatives from each group, the study integrates helium porosity and gas permeability measurements with µ-CT imaging at various resolutions (5 µm, 2 µm, and 1 µm). The findings reveal that µ-CT resolution significantly affects the discernibility and characterization of pore structures. Finer resolutions (2 µm and 1 µm) effectively uncovered interconnected pore networks in medium- to coarse-grained sandstones, suggesting favorable properties for geothermal applications. In contrast, fine-grained samples showed limitations in geothermal applicability at higher resolutions due to their compact nature and minimal pore connectivity, which could not be confidently imaged at 1 µm. Additionally, this study acknowledges the challenges in delineating the boundaries within the Dunántúli Group formations, which adds a layer of complexity to the characterization process. The research highlights the importance of aligning µ-CT findings with geological backgrounds and laboratory measurements for accurate pore structure interpretation in heterogeneous formations. By contributing vital petrophysical data for the Dunántúli Group and the Pannonian Basin, this study provides key insights for selecting appropriate µ-CT imaging resolutions to advance sustainable geothermal energy strategies in the region. The outcomes of this research form the basis for future studies aimed at developing experimental setups to investigate physical clogging and enhance geothermal exploitation methods, crucial for the sustainable development of geothermal resources in the Pannonian Basin. Full article

Knowledge of the precise anatomy and dimensions of the pulp chambers in different teeth allows the odontologist to perform correct diagnosis, as well as treatment planning and monitoring. Clinical practice has introduced cone-beam computed tomography (CB-CT) as a method to evaluate the morphology and dimensions of the pulp chamber. Nevertheless, micro-computed tomography (micro-CT) is regarded as the gold standard in approaching those topics. Here, we have designed an algorithm that takes as input DICOM images from in vivo CB-CT of permanent molars to determine the accuracy of CB-CT for evaluation of pulp chamber volume. The values were compared with those from in vivo CB-CT (rough and expert-manipulated) and ex vivo micro-CT. The relative errors obtained in the volume calculated by the algorithm vs. the volume measured by micro-CT did not exceed 5.7%; additionally, no significant differences were found between algorithm volumes and manipulated CB-CT volumes, while all volumes were different from those obtained with automatic CB-CT software. These data demonstrate that this CB-CT-based volume algorithm may be a reliable technique for evaluation of the pulp chamber volume in permanent molars and can be useful in the diagnosis of pulp diseases, as well as in the planning and monitoring of their treatments. Full article

Our study aimed to investigate the role of ferroptosis in sevoflurane-induced hearing impairment and explore the mechanism of the microRNA-182-5p (miR-182-5p)/Glutathione Peroxidase 4 (GPX4) pathway in sevoflurane-induced ototoxicity. Immunofluorescence staining was performed using myosin 7a and CtBP2. Cell viability was assessed using the CCK-8 kit. Fe²⁺ concentration was measured using FerroOrange and Mi-to-FerroGreen fluorescent probes. The lipid peroxide level was assessed using BODIPY 581/591 C11 and MitoSOX fluorescent probes. The auditory brainstem response (ABR) test was conducted to evaluate the hearing status. Bioinformatics tools and dual luciferase gene reporter analysis were used to confirm the direct targeting of miR-182-5p on GPX4 mRNA. GPX4 and miR-182-5p expression in cells was assessed by qRT-PCR and Western blot. Ferrostatin-1 (Fer-1) pretreatment significantly improved hearing impairment and damage to ribbon synapses in mice caused by sevoflurane exposure. Immunofluorescence staining revealed that Fer-1 pretreatment reduced intracellular and mitochondrial iron overload, as well as lipid peroxide accumulation. Our findings indicated that miR-182-5p was upregulated in sevoflurane-exposed HEI-OC1 cells, and miR-182-5p regulated GPX4 expression by binding to the 3′UTR of GPX4 mRNA. The inhibition of miR-182-5p attenuated sevoflurane-induced iron overload and lipid peroxide accumulation. Our study elucidated that the miR-182-5p/GPX4 pathway was implicated in sevoflurane-induced ototoxicity by promoting ferroptosis. Full article

This research aims to investigate the influence of model height employed in the deep drawing of orthodontic aligner sheets on force transmission and aligner thickness. Forty aligner sheets (Zendura FLX) were thermoformed over four models of varying heights (15, 20, 25, and 30 mm). Normal contact force generated on the facial surface of the upper right central incisor (Tooth 11) was measured using pressure-sensitive films. Aligner thickness around Tooth 11 was measured at five points. A digital caliper and a micro-computed tomography (µ-CT) were employed for thickness measurements. The normal contact force exhibited an uneven distribution across the facial surface of Tooth 11. Model 15 displayed the highest force (88.9 ± 23.2 N), while Model 30 exhibited the lowest (45.7 ± 15.8 N). The force distribution was more favorable for bodily movement with Model 15. Thickness measurements revealed substantial thinning of the aligner after thermoforming. This thinning was most pronounced at the incisal edge (50% of the original thickness) and least at the gingivo-facial part (85%). Additionally, there was a progressive reduction in aligner thickness with increasing model height, which was most significant on the facial tooth surfaces. We conclude that the thermoplastic aligner sheets undergo substantial thinning during the thermoforming process, which becomes more pronounced as the height of the model increases. As a result, there is a decrease in both overall and localized force transmission, which could lead to increased tipping by the aligner and a diminished ability to achieve bodily movement. Full article