Search Results (65)

Numerical simulations were conducted to analyze the unsteady aerodynamic characteristics of a tiltrotor aircraft with different conversion strategies. Firstly, the CFD method was established by taking the interaction between the rotor and wing into account, as well as the body-fitted grid of the tiltrotor. Then, the trimming approach of the rotor and wing was developed to ensure longitudinal balance of the aircraft, and the method for determining the conversion corridor of the tiltrotor aircraft was proposed by considering the limitations imposed by wing stall and the required power of the rotor. Finally, the aerodynamic characteristics of the rotor and wing during the continuous conversion process were investigated, considering various tilting angular velocities and horizontal accelerations of the tiltrotor. The numerical results indicated that a smaller acceleration can enhance the efficiency of the tiltrotor. However, this would increase the complexity of trimming the fuselage attitude angle. It was also found that excessive acceleration could exceed the required power limit of the tiltrotor, rendering the conversion strategy infeasible. Full article

In recent years, there has been a significant amount of research on tiltrotor multicopter unmanned aerial vehicles (TM-UAVs) in aerial robotics. Despite the varying frame types of TM-UAVs, they all still aim to decouple the propeller from the body, which means that the propeller’s attitude control is independent of the body’s attitude control. On the one hand, this solves the issue of multicopter unmanned aerial vehicles (M-UAVs) being limited by small roll and pitch angles, thereby improving flight performance. On the other hand, it addresses the drawbacks of M-UAVs as typical underactuated systems. However, the fact still remains that it cannot significantly change thrust direction, thus providing the necessary wrench direction for aerial manipulation. This paper presents a pitch-axis tiltrotor quadcopter unmanned aerial vehicle (UAV) design named Tilt-X, which can maximize horizontal pulling force and yaw moment when used as an aerial manipulator. This design contributes to tasks such as pushing, pulling, and twisting. The reliability of the design has been demonstrated through dynamic modeling and experimental validation. Full article

Incremental nonlinear dynamic inversion (INDI) is a widely used approach to controlling UAVs with highly nonlinear dynamics. One key element of INDI-based controllers is the control allocation realizing pseudo controls using available actuators. However, the tracking of commanded pseudo controls is not the only objective considered during control allocation. Since the approach only works locally due to linearization and the solution is often ambiguous, additional aspects like control efforts or penalizing the deviation of certain states must be considered. Conducting the control allocation by solving a quadratic program this results in a considerable number of weighting parameters, which must be tuned during control design. Currently, this is conducted manually and is therefore time consuming. An automated approach for tuning these parameters is therefore highly beneficial. Thus, this paper presents and evaluates a model-based approach automatically tuning the control allocation parameters of a tiltrotor VTOL using an optimization algorithm. This optimization algorithm searches for optimal parameters minimizing a cost functional that reflects the design target. This cost functional is calculated based on a test mission for the VTOL which is conducted within a simulation environment. The test mission represents the common operating range of the VTOL. The simulation environment consists of an aircraft model as well as a model of the INDI-based controller which is dependent on the control allocation parameters. On this basis, model-based optimization is conducted and the optimal parameters are identified. Finally, successful real-world tests on a 4-degrees-of-freedom testbench using the identified parameters are presented. Since the control allocation parameters can significantly influence the aircraft’s stability, the 4-DOF testbench for the aircraft is required for rapid validation of the parameters at a minimum amount of risk. Full article

A data-driven aerodynamic modeling method is proposed to address the problem that traditional modeling methods based on physical mechanisms cannot fully represent the special aerodynamic characteristics of tiltrotor evtol aircraft. By analyzing the uniquely complex aerodynamic characteristics of electric vertical take-off and landing (evtol) aircraft, an MLP neural network model has been constructed that reflects the coupling characteristics between influencing factors. Using the XV15 wind tunnel test data, a dataset was constructed, and the neural network model was trained and validated. Simulation results show that the selected data-driven method can accurately predict the aerodynamic characteristics of the longitudinal transition phase of the tiltrotor evtol. Full article

The stabilisation capabilities of unmanned aerial vehicles (UAVs) with bicopter underactuated swashplateless rotors are highly sensitive to motor-induced vibration. Due to the requirement of the active control of underactuated swashplateless rotors, conventional designs are limited in reducing vibration through control optimisation. A solution with customized passive spring-damping structures on a unique underactuated swashplateless rotor of a tiltrotor bicopter platform is presented. The implementation of this structure effectively reduces the self-coherent vibration in flights. As a result, a higher level of control authority has been achieved without setting excessive low-pass filtering for vibration. Experimentally obtained inertial measurement unit (IMU) data, rotor speed, rotor tilt angle, and the cyclic stator response are presented for comparison with Simulink model predictions. Full article

In the vertical take-off and landing (VTOL) state of tiltrotor aircraft, the inlet entrance encounters the incoming airflow at a 90° attack angle, resulting in highly complex internal flow characteristics that are extremely susceptible to gusts. Meanwhile, the flow quality at the inlet exit directly affects the performance of the aircraft’s engine. This work made use of an unsteady numerical simulation method based on sliding meshes to investigate the internal flow characteristics of the inlet during the hover state of a typical tiltrotor aircraft and the effects of head-on gusts on the inlet’s aerodynamic characteristics. The results show that during the hover state, the tiltrotor aircraft inlet features three pairs of transverse vortices and one streamwise vortex at the aerodynamic interface plane (AIP). The transverse vortices generated due to the rotational motion of the air have the largest scale and exert the strongest influence on the inlet’s performance, which is characterized by pronounced unsteady features. Additionally, strong unsteady characteristics are present within the inlet. Head-on gusts mainly affect the mechanical energy and non-uniformity of the air sucked into the inlet by influencing the direction of the rotor’s induced slipstream, thereby impacting the performance of the inlet. The larger head-on gusts have beneficial effects on the performance of the inlet. When the gust velocity reaches 12 m/s, there is a 1.01% increase in the total pressure recovery (σ) of the inlet, a 25.72% decrease in the circumferential distortion index (DC60), and a reduction of 62.84% in the area where the swirl angle |α| exceeds 15°. Conversely, when the gust velocity of head-on gusts reaches 12 m/s in the opposite direction, the inlet’s total pressure recovery decreases by 1.13%, the circumferential distortion index increases by 14.57%, and the area where the swirl angle exceeds 15° increases by 69.59%, adversely affecting the performance of the inlet. Additionally, the presence of gusts alters the unsteady characteristics within the inlet. Full article

The evolution of aircraft wing development has seen significant progress since the early days of aviation, with static testing emerging as a crucial aspect for ensuring safety and reliability. This study focused specifically on the engineering phase of static testing for the Clean Sky 2 T-WING project, which is dedicated to testing the innovative composite wing of the Next-Generation Civil Tiltrotor Technology Demonstrator. During the design phase, critical load cases were identified through shear force/bending moment (SFBM) and failure mode analyses. To qualify the wing, an engineering team designed a dedicated test rig equipped with hydraulic jacks to mirror the SFBM diagrams. Adhering to specifications and geometric constraints due to several factors, the jacks aimed to minimize the errors (within 5%) in replicating the diagrams. An effective algorithm, spanning five phases, was employed to pinpoint the optimal configuration. This involved analyzing significant components, conducting least square linear optimizations, selecting solutions that met the directional constraints, analyzing the Pareto front solutions, and evaluating the external jack forces. The outcome was a test rig setup with a viable set of hydraulic jack forces, achieving precise SFBM replication on the wing with minimal jacks and overall applied forces. Full article

In recent years, there has been rapid development in electric aircraft, particularly electric vertical takeoff and landing (eVTOL) aircraft, as part of efforts to promote green aviation. During the conceptual design stage, it is crucial to select appropriate values for key parameters and conduct sensitivity analysis on these parameters. This study focuses on an electric tilt-rotor aircraft and proposes a performance analysis method for electric aircraft while developing a general design tool specifically for this type of aircraft. Subsequently, the impact of wing incidence angle, sweep angle, span, propeller solidity, battery-specific energy, and battery mass on range, maximum takeoff weight, and hover power are analyzed. The results show that the battery mass, wingspan, and wingtip chord length have great effects on the maximum takeoff weight; among these, battery mass had the greatest influence. In terms of range, the battery energy density has a great positive effect on range, while the increase in wing angle of incidence, wingtip chord length and battery mass have some negative effects on range. Full article

The research described in this paper focuses on the development of an innovative unmanned aerial vehicle (UAV) tailored for a specific mission: detecting the acoustic signature emitted by chainsaws, identifying deforestation, and reporting its location for legality assessment. Various calculations were conducted to determine the optimal solution, resulting in the choice of a fixed-wing UAV. A comparative analysis between tri-rotor and quadcopter systems was performed, leading to the selection of the tri-rotor configuration. The primary objective of this study is to design an innovative hybrid UAV concept with key features including a fixed-wing design and integrated VTOL (vertical takeoff and landing) capability in the experimental model. The aircraft has been constructed using advanced materials such as fiber-reinforced polymer composites, manufactured using both conventional and advanced techniques like continuous fiber additive manufacturing and the use of a polymer matrix. Additionally, the aerodynamic configuration is optimized to achieve a cruise speed of approximately 50 km/h and a flight autonomy exceeding 3 h. The UAV has been equipped with payloads for mounting sensors to collect meteorological data, and crucially, the VTOL system has been optimized to vectorize thrust for improved performance during the transition from hover to cruise flight. This paper details the entire manufacturing and assembly process of the drone, covering both the structural framework and associated electrical installations. A dedicated sound detection system is incorporated into the drone to identify chainsaw noise, with the aim of preventing deforestation. Full article

The tilt-wing aircraft has attracted widespread attention due to its excellent performance. However, its aerodynamic characteristics during the tilt transition section are characterized by unsteadiness, nonlinearity, and strong coupling, making it difficult to control. Using computational fluid dynamics (CFD) methods and moving overset grids to control the tilt-wing motion, the momentum source method is employed to replace actual propellers. The influence of the propeller on the aerodynamic characteristics of the tiltrotor at different tilt angles is investigated under incoming flow velocities of 8 m/s and 45 m/s in steady conditions. Additionally, the differences between steady and unsteady calculations of the tilt transition section are investigated at incoming flow velocities of 8 m/s, 15 m/s, 30 m/s, and 45 m/s in unsteady conditions. The research results indicate the following information: 1. the slipstream from the propellers significantly enhances the lift, drag, and stall angle of attack of the tilt-wing aircraft but reduces the lift-to-drag ratio; 2. there are noticeable differences in the forces acting on the tilt-wing aircraft between steady calculations with fixed tilt angles and unsteady calculations with continuous tilting. Full article

This study addresses the crucial role of post-buckling behavior analysis in the structural design of composite aeronautical structures. Traditional engineering practices tend to result in oversized composite components, increasing structural weight. EASA AMC 20-29’s Building Block Approach suggests phased testing, but its time and cost challenges necessitate a shift to high-fidelity post-buckling analyses, exemplified by MSC NASTRAN SOL 400. This approach, showcased in the analysis of the Next Generation Civil Tilt Rotor Technology Demonstrator’s wing (NGTCTR-TD), effectively de-risks static tests, contributing to a more efficient certification process. The study demonstrates how advanced simulations provide detailed insights into local buckling phenomena, allowing precise stress distribution analysis. These analyses eliminate the risk of structural failure, paving the way for safer, more efficient, and cost-effective airframe structures. Future developments aim to validate numerical analyses with experimental data, further emphasizing the reliability and benefits of high-fidelity simulations. Full article

Recent developments in electrical Vertical Take-off and Landing (eVTOL) vehicles show the need for a better understanding of transient aero-mechanical propeller loads for non-axial inflow conditions. The variety of vehicle configurations conceptualized with different propellers in terms of blade geometry, number of blades, and their general integration concept results in aerodynamic loads on the propellers which are different from those on conventional fixed-wing aircraft propellers or helicopter rotors. Such varying aerodynamic loads have to be considered in the vehicle design as a whole and also in the detailed design of their respective electric propulsion systems. Therefore, an experimental approach is conducted on two different propeller blade geometries and a varying number of blades with the objective to explore the characteristics at non-axial inflow conditions. Experimental data are compared with calculated results of a low-fidelity Blade Element Momentum Theory (BEMT) approach. Average thrust and side force coefficients are shown to increase with inflow angle, and this trend is captured by the implemented numerical method. Measured thrust and in-plane forces are shown to oscillate at the blade passing frequency and its harmonics, with higher amplitudes at higher angles of inflow or lower number of blades. Full article

Tilt-rotor unmanned aerial vehicles combine the advantages of multirotor and fixed-wing aircraft, offering features like rapid takeoff and landing, extended endurance, and wide flight conditions. This article provides a summary of the design, modeling, and control of a composite tilt-rotor. During modeling process, aerodynamic modeling was performed on the tilting and non-tilting parts based on the subcomponent modeling method, and CFD simulation analysis was conducted on the entire unmanned aerial vehicle to obtain its accurate aerodynamic characteristics. In the process of modeling the motor propeller, the reduction of motor thrust and torque due to forward flow and tilt angle velocity is thoroughly examined, which is usually ignored in most tilt UAV propeller models. In the controller design, this paper proposes a fusion ADRC control strategy suitable for vertical takeoff and landing of this type of tiltrotor. The control system framework is built using Simulink, and the control algorithm’s efficiency has been verified through simulation testing. Through the proposed control scheme, it is possible for the composite tiltrotor unmanned aerial vehicle to smoothly transition between multirotor and fixed-wing flight modes. Full article

This paper presents a methodology that involves the development of high-fidelity modeling and simulation procedures aimed at supporting virtual certification for crashworthiness requirements specific to tiltrotor aircraft, addressing the critical need for accurate safety requirement fulfillment predictions and weight containment of wing. The unique crashworthiness requirement for tiltrotor wings necessitates a design that can ensure a controlled failure during survivable crash events. This is to alleviate the inertial load acting on the fuselage, thereby protecting occupants from injuries and fire while ensuring the integrity of escape paths. The objective of this methodology is to simulate the crash effects on the entire wing using explicit, non-linear, and time-dependent FE analysis. This approach verifies the spanwise placement of the frangible sections, the mode of failure, the loads acting on the fuselage links, and the acceleration transmitted to the structure. This study focuses on a standalone analysis. Full article

The T-WING project, a CS2-CPW (Clean Sky 2 call for core partner waves) research initiative within FRC IADP (Fast Rotor-Craft Innovative Aircraft Demonstrator Platform), focuses on developing, qualifying and testing the new wing of the Next-Generation Civil Tilt-Rotor (NGCTR). This paper introduces a case study about a methodology for refining the stick-beam model for the NGCTR wing, aligning it with the GFEM (Global Finite Element Model) wing’s dynamic characteristics in terms of modal frequencies and mode shapes. The initial stick-beam model was generated through the static condensation of the GFEM wing. The tuning process was formulated as an optimization problem, adjusting beam properties to minimize the sum of weighted quadratic errors in modal frequencies and Modal Assurance Criterion (MAC) values. Throughout the optimization, the MAC analysis ensured that the target modes were tracked, and, at each iteration, a new set of variable estimates were determined based on the gradient vector and Hessian matrix of the objective function. This methodology effectively fine-tunes the stick-beam model for various mass cases, such as maximum take-off weight (MTOW) and maximum zero-fuel weight (MZFW). Full article