Applied Mechanics

Current trends show that wind turbines are growing in size to meet a rising demand for renewable energy generation, and their upscaled rotors have inherently become more flexible to maintain a proportionally lighter design. This is because larger rotors must be less massive relative to their diameter to minimize the levelized cost of energy (LCOE), which means that blades that are notably less stiff are produced as a result. These structural changes to blades are often reflected in their compromised aeroelastic stability and amplified deformation during operation, which has the potential to decrease the blade’s expected lifetime and the performance of the machine overall. Variations in blade flexibility are also known to influence vortex-wake structures downstream of the turbine, causing patterns of velocity deficit to evolve in ways that affect the performance of other turbines in the farm. This research explores how the increased flexibility of modern utility-scale wind turbine blades influences rotor aeroelastic behavior and interactions with farm flow. High-fidelity simulations of Sandia National Laboratories’ (SNL) National Rotor Testbed (NRT) wind turbine are presented. Flexible variations of the NRT baseline blade are simulated in a variety of realistic operational conditions typically expected at the SNL’s SWiFT facility in Lubbock, Texas. Solutions are then compared to investigate how specific changes to the structural properties of the NRT baseline blade’s design and construction can influence its aeroelastic response at the rotor and the evolution of the turbine’s wake. Full article

A new moment-resisting mass timber connection was designed based on the principles of force equilibrium in applied mechanics. The connection configuration utilizing two mechanically fastened threaded steel rods embedded into the end of a glulam beam section was experimentally investigated in this study. A gradually increasing transverse load was applied to the free end of a cantilevered beam, causing a bending moment on the beam-end connection until failure. Four different connection configurations were examined, each replicated twice to verify results. The beam connection parameters investigated were rod anchorage length (200 and 250 mm) and square washer size (38.1 and 50.8 mm). Test results show that increasing the washer size increased the connection bending strength by increments more significantly than those due to increasing the rod anchorage length. However, the connection configurations with the smaller-size washer, which failed mainly due to wood crushing under the washer, had higher ductility ratios than those with the larger-size washer, which failed due to steel rod yielding. In a real-life scenario, a structural element such as a glulam beam is usually loaded to approximately 50% to 70% of its design capacity, considering a reasonable margin of safety. The study estimates a maximum possible bending moment utilization factor for the strongest connection configuration that ranged between 34% and 48% compared to the maximum moment resistance of a supported glulam beam spanning an average length of 4.0 m to 6.0 m (a common span length in framed timber buildings) and has a cross-section size same as the one utilized in this study. This utilization factor is quite large for a timber connection, and thus, confirms a considerable moment-resisting capability of the new configuration developed in this study. Full article

A variety of hollow microneedle (HMN) designs has emerged for minimally invasive therapies and monitoring systems. In this study, a design change limiting the indentation depth of the (3D) printed custom microneedle assembly (circular array of five conical frusta with and without a stopper, aspect ratio = 1.875) fabricated using stereolithography has been experimentally validated and modeled in silico. The micro-indentation profiles generated in confined compression on 1 mm ± 0.073 mm alginate films enabled the generation of a Prony series, where displacement ranged from 100 to 250 µm. These constants were used as intrinsic properties simulating experimental ramp/release profiles. Puncture occurred on two distinct hydrogel formulations at the design depth of 150 µm and indentation rate of 0.1 mm/s characterized by a peak force of 3.5 N (H = 31 kPa) and 8.3 N (H = 36.5 kPa), respectively. Experimental and theoretical alignments for peak force trends were obtained when the printing resolution was simulated. Higher puncture force and uniformity inferred by the stopper was confirmed via microscopy and profilometry. Meanwhile, poroviscoelasticity characterization is required to distinguish mass loss vs. redistribution post-indentation through pycnometry. Results from this paper highlight the feasibility of insertion-depth control within the epidermis thickness for the first time in solid HMN literature. Full article

A new data-driven continuum model based on an artificial neural network is developed in this study for a new three-dimensional lattice-structured material design. The model has the capability to capture and predict the nonlinear elastic behaviour of the specific lattice-structured material in the three-dimensional continuum description after being trained through the appropriate dataset. The essential data as the input ingredients of the data-driven model are provided through a hybrid method including experimental and unit-cell level finite element simulations under comprehensive loading scenarios including uniaxial, biaxial, volumetric, and pure shear loading. Furthermore, the lattice-structured samples are also fabricated using SLA additive manufacturing technology and the experimental measurements are performed and used for validation of the model. This then illustrates that the current model/methodology is a robust and powerful numerical tool to conduct the homogenization in complex simulation cases and could be used to accelerate the analysis and optimization during the design process of new lattice-structured materials. The model could also easily be used for other engineered materials by updating the dataset and re-training the ANN model with new data. Full article

Composite curing through infrared radiation (IR) has become a popular autoclave alternative due to lower energy costs and short curing cycles. As such, understanding and measuring the effect of all parameters involved in the process can aid in selecting the proper constituents as well as curing cycles to produce parts with a high degree of cure and low curing time. In this work, a numerical model that takes inputs such as part geometry, material properties, curing-related properties and applied curing cycle is created. Its outputs include the degree of cure, maximum curing temperature and total curing time. A genetic algorithm and a design of experiments (DOE) sequence cover the range of each input variable and multiple designs are evaluated. Correlations are examined and factor analysis on each output is performed, indicating that the most important inputs are activation energy, specimen precuring, applied curing temperature and curing duration, while all the others can be considered constant. Finally, response surfaces are created in order to effectively map and provide estimations of the design space, resulting in a curing cycle optimizer given certain restrictions over the input parameters. Full article

Face milling is among the processes that can produce a high-precision surface finish. Tool condition monitoring and signal processing algorithms are under extensive research to improve production quality and productivity in machining processes. In the present research, the time–frequency analysis technique was applied to the signal obtained from a sensor integrated into the primary AC power circuitry during the milling of steel bars to evaluate its applicability in detecting the current variations associated with the cutting force. The signal acquired from the sensor was processed in the time–frequency domain using wavelet analysis, and the results were compared with the traditional time and frequency analyses. The results showed that the signal variations produced by the cutting force were well localized in the frequency spectra with both approaches. However, the wavelet processing method yielded a poorly defined cutting force signal shape due to the limited resolution inherent in the sub-bands containing the frequencies of interest. Full article

Due to the shear strain in the plane of the slab, the parts of the slab remote from the steel beam lag behind the part of the slab located in its proximity. This shear lag effect causes a non-uniform stress distribution across the width of the slab. As a result, several standards have introduced the concept of an effective flange width to simplify the analysis of stress distribution across the width of composite beams. Both the computed ultimate moment and serviceability limit states are directly impacted by the effective width. The effect of using a large number of contact points as shear connectors on the effective width of a steel beam flange has not been investigated. A three-dimensional finite element analysis is carried out in this paper. The ABAQUS software (version 6.14) is used for this purpose, where several variables are considered, including the surface area connecting the steel beam and concrete slab, the transverse space, and the number of shear connectors. It was discovered that the number of shear connectors on the steel beam flange has a major impact on the effective width. The many connectors work together to provide a shear surface that improves the effective width by lowering the value of the shear lag. Full article

In Korea, the underground silo structure for low- and intermediate-level radioactive waste disposal facilities has been constructed and operated since 2014. Large-scale earthquakes occurred in 2016 and 2017, respectively, in Gyeongju and Pohang areas near the underground silo structures, and interest in the stability of the underground silo increased significantly. In this paper, one-dimensional free-field analyses have been carried out before the three-dimensional silo dynamic analyses subjected to earthquake loadings. As an additional study, a new form of the finite element equilibrium equation is derived in terms of relative motions, which is essentially the same equation expressed in terms of total motions where the base shear force is applied to the earthquake load. The accuracy of conventional finite element solutions is evaluated by directly comparing them with closed-form solutions by frequency domain analysis such as SHAKE91. Full article

The finite volume method (FVM) was used to model a tungsten inert gas (TIG) arc welding process. A two-dimensional axisymmetric model of arc plasma integrating fluid–solid coupling was developed by solving electromagnetic and thermal equations in both the gas domain and the solid cathode. In addition, two additional coupling equations were considered in the gaseous domain where the arc is generated. This model also included the actual geometry of torch components such as the gas diffuser, the nozzle, and the electrode. The model was assessed using numerous numerical examples related to the prediction of the argon plasma mass fraction, temperature distribution, velocity fields, pressure, and electric potential in the plasma. A new linearization method was developed for the source term in the energy conservation equation, allowing for the prediction of Joule effects without artificial conductibility. This new method enhances the efficiency of the classical approach used in the literature. Full article

An understanding of the dynamic behavior of materials plays a crucial role in machining improvement. According to the literature on this issue, one of the alloys whose dynamic behavior has been investigated less is AA 5052-H34, despite its numerous industrial applications. Using finite element (FE) modeling greatly reduces machining research costs. This research delved into the dynamic behavior modeling of AA 5052-H34 during dry-turning FE simulation. The dynamic behavior of AA 5052-H34 was achieved using the Johnson–Cook (J-C) constitutive equation, which was calculated using the uniaxial tensile and Split-Hopkinson pressure bar (SHPB) tests. To confirm the accuracy of the material model, these SHPB tests were then simulated in Abaqus. The J-C constitutive equation, paired with a J-C damage criterion, was employed in a chip formation and cutting temperature simulation. It was found that the feed rate significantly influences the dynamic behavior of AA 5052-H34. The thickness and morphology of the chip were investigated. The experimental and numerical chip thicknesses showed a direct relationship with the feed rate. The simulation temperature was also analyzed, and, as expected, it showed an upward trend with increasing cutting speed and feed rate. Then, the accuracy of the proposed FE simulation was confirmed by the agreement of the experimental and simulation results. Full article

In this work, we explore a simplified model based on both analytical and computational methods for the study of film-boiling droplet motion on microscale ratchets. We consider a specific ratchet design with the length periods and depth of ratchets much smaller than the size of the droplet. We conclude based on our modeling that for the ratchet configuration considered in this paper, the conduction within the vapor film is the dominant means of heat transfer in comparison with convection and radiation. Furthermore, we demonstrate a more manageable two-dimensional model in which analytical approaches coupled with computational approaches yield reasonably accurate results in comparison to the actual experiments. Full article

Interference fits are very common shaft–hub connections due to their low manufacturing costs and excellent technical properties. The Plastic Conditioning of this machine element is a new and not very well-known method. During the development of this method, it was discovered that Reverse Yielding occurs in certain applications and has a negative impact on the result. This paper examines the effects of Reverse Yielding on the technology of Plastic Conditioning of interference fits in Power Transmission Engineering. Based on the Shear Stress Hypothesis (SH), the Plane Stress State (PSS), and the ideal plastic behavior of materials, established stress–mechanical relationships are used to find the influencing parameters of Reverse Yielding on the technology of Plastic Conditioning and their limits. As a result, a new computational concept is developed that allows the user to maximize Plastic Conditioning while avoiding Reverse Yielding. Analytical calculation suggestions and diagrams for practical application are provided. Furthermore, the deviations in the obtained results, taking into account other material models such as the Von Mises Yield Criterion (VMYC) and material hardening, as well as the Bauschinger effect, are examined in comparison with our own numerical results from the development of Plastic Conditioning, and the resulting need for further research is defined. In addition, the method of Plastic Conditioning of interference fits is introduced and its basic principles are briefly explained. Full article

A smoothed-particle hydrodynamics (SPH) modeling technique was applied in conjunction with the Johnson–Holmquist (JH-2) ceramic material constitutive model to replicate the fracture of soda-lime glass in a milling manufacturing process. Four-point bending tests were conducted to validate the soda-lime glass bulk material properties prior to its implementation in ABAQUS CAE™ Explicit (Version 2017). The JH-2 material constitutive model replicated the fracture load and time to fracture for the four-point bending load cases as per ASTM C158. This study showed how SPH in combination with a validated JH-2 material model in a milling process simulation was able to replicate the output size distribution at 5000 and 6500 revolutions per minute (RPM). For operations at 3000 RPM or lower, it was shown that it is necessary to include additional effects in the model, such as fluid–structure interactions, to improve the correlation with the experimental data. The SPH model was validated through an experimental campaign using high-speed cameras and a particle Camsizer. The experimental results clearly indicate a direct relation between the mill’s RPM and the output particle size distribution. Full article

In recent years, there has been a significant increase in the use of structural health monitoring (SHM) technologies as systems for monitoring the integrity of aircraft’s structures. The use of compact and embeddable sensor networks, like the ones based on fibre optics (FO), is particularly attractive from the perspective of releasing an integrated structural system with intrinsic sensing capacity. Usually, an SHM system architecture is completed by a dedicated algorithm that processes the data gathered from the sensors to elaborate on the level of damage currently suffered by the structure, with the further possibility of providing information to the relevant specialists involved with its supervision. One of the main SHM applications that is attracting major interest is related to the inspection and detection of anomalies in bonded joints, which is extremely relevant in many composite realizations. Aeronautical regulations allow the use of bonded joints on an aircraft’s primary structure but require the implementation of a means to ensure their absolute safety, such as the introduction of further mechanical links aimed at stopping the propagation of a possible flaw or the availability of Non-Destructive Inspection (NDI) systems to prove the absence of relevant damaged areas. Generally, the main typical defects occurring during the manufacturing of bonded joints include adhesive curing, kissing bonds, poor porosity, and poor surface preparation. The current NDI systems more widely used and available to detect defects are still inaccurate due to the lack of standard procedures for the creation of representative defects in a controlled manner, which would allow for the development of reliable methodologies and tools able to ensure the safety of a bonded joint, as required by safety regulations. This paper shows the results relative to the implementation of an SHM system developed by the Italian Aerospace Research Centre (CIRA) aimed at monitoring the bonding lines between spar caps and panels of a typical composite wingbox section and detecting faults in location and length. The work was performed during typical ground static tests by using a fibre optical sensing network embedded within relevant adhesive paste layers during the manufacturing process of the structure. In the reported investigation, the SHM system assumed the function of an NDI system tool. The results show that the developed SHM system has good reliability for the detection of both the position and size of damage areas that were artificially inserted within the test article during the bonding phase, showing its potential as a candidate to be used as a tool to verify the conditions of a bonded joint, as required by aviation authorities’ regulations. Full article

This study presents an investigation of the effects of structural characteristics, such as the layer height, infill density, top/bottom layer line directions and infill pattern, on the structural efficiency of Acrylonitrile Butadiene Styrene (ABS)-based specimens. The Fused Filament Fabrication (FFF) technique was utilized for the specimen fabrication, and the Ultimate Tensile Strength (UTS) and Strength-to-Mass (S/M) ratio were examined. The tests were planned according to the Central Composite Design (CCD), and an empirical model for each response was developed, with respect to the applied factors and their interactions. The analysis revealed that the characteristics with the strongest influence on the UTS and the S/M ratio were the infill and the layer height, respectively. Moreover, it was observed that the honeycomb structure contributed to the highest UTS compared to the other patterns. Finally, an optimization analysis based on the desirability function was performed, highlighting the combination of a 0.3 mm layer, 21.81% and 76.36% infill, 0° direction and the honeycomb pattern as the optimal for maximizing both UTS and S/M ratio under different desirability. Full article

Polymer hybrid composites and hybrid polymer composites are distinct but interconnected composite classes, each with unique compositions and design philosophies. The mechanical properties of these composites are vital in advanced materials due to their impacts on performance, durability, and suitability for various applications. The addition of ionic liquids into these composites is a promising innovation in advanced materials. In this short review, various polymer matrices (e.g., thermosets, thermoplastics, and biopolymers), fillers (e.g., inorganic, carbon, organic, and metal), and ionic liquids (e.g., imidazolium- and phosphonium-based) used to fabricate polymer hybrid composites and hybrid polymer composites with added ionic liquids are identified. Furthermore, the addition of ionic liquids into these composites through different methods (e.g., magnetic stirring, mechanical stirring, solid grinding, etc.) is discussed. The influence of ionic liquid addition on the mechanical properties, specifically the tensile properties of these composites, is also shortly reviewed. The changes in the tensile properties, such as the tensile strength, tensile modulus, and elongation at break, of these composites are explained as well. The information presented in this review enhances the understanding of the methods applied to add ionic liquids into polymer hybrid composites and hybrid polymer composites, along with their tensile properties. In short, some ionic liquids have the capacity to enhance the tensile properties of hybrid polymer composites, and several ionic liquids can reduce the tensile properties of polymer hybrid composites. Full article

The attractiveness of the boundary element method—the reduction in the problem dimension by one—is lost when solving nonlinear solid mechanics problems. The point collocation method applied to strong-form differential equations is appealing because it is easy to implement. The method becomes inaccurate in the presence of traction boundary conditions, which are inevitable in solid mechanics. A judicious combination of the point collocation and the boundary integral formulation of Navier’s equation allows a pure boundary element method to be obtained for the solution of nonlinear elasticity problems. The potential of the approach is investigated in some simple examples considering isotropic and anisotropic material models in the total Lagrangian framework. Full article

This study aims to develop an integrated approach for 3D lumbar vertebral biomodel design and analysis, specifically targeting unilevel disc degeneration and the replacement of lumbar artificial discs. Key objectives include improving existing design methods through 3D techniques, inverse modeling, and an engineering biomodel preparation protocol. Additionally, the study evaluates mechanical properties in the implantation area and between disc components to gauge the effectiveness of artificial discs in restoring functional movement within the studied biological model. The construction of a biological model representing the L3–L4 functional spinal unit was based on measurements from radiographic images and computed tomography data obtained from the study sample. The 3D finite element method in Ansys software (v. 19.2, ANSYS, Inc., Canonsburg, PA, USA) was used to monitor the distribution of equivalent stress values within the core of the two artificial discs and the behavior of vertebral bone components in the model. This approach enabled the creation of personalized digital models tailored to the specific implantation requirements of each patient. Stress analysis identified critical areas within the disc cores, suggesting potential design modifications to optimize artificial disc performance, such as selectively increasing core thickness in specific regions and considering adjustments during implantation. For example, preserving part of the lateral annulus fibrosus from the degenerative disc and maintaining the anterior and posterior longitudinal ligaments may play a crucial role in balancing the forces and moments experienced by the lumbar section. This study provides valuable insights into the development of patient-specific solutions for lumbar disc degeneration cases, with the potential for enhancing artificial disc design and implantation techniques for improved functional outcomes. Full article